Professional Documents
Culture Documents
Attachment TE PDF
Attachment TE PDF
WAKE FREQUENCY CALCULATION
Document No. Pekerjaan Engineering, Procurement & Rev. : 2
LREF-00-VDR/CSP4-CAL-60- Construction (EPC) Proyek Pembangunan Sheet No.
0001-A4 Terminal LPG Refrigerated 1 of 44
WAKE FREQUENCY CALCULATION
Document No. Pekerjaan Engineering, Procurement & Rev. : 2
LREF-00-VDR/CSP4-CAL-60- Construction (EPC) Proyek Pembangunan Sheet No.
0001-A4 Terminal LPG Refrigerated 2 of 44
REVISION SHEET
1 1 4
- There is comment on WFC Rev.0.
refer to response below.
Response :
WAKE FREQUENCY CALCULATION
Document No. Pekerjaan Engineering, Procurement & Rev. : 2
LREF-00-VDR/CSP4-CAL-60- Construction (EPC) Proyek Pembangunan Sheet No.
0001-A4 Terminal LPG Refrigerated 3 of 44
TABLE OF CONTENTS
WAKE FREQUENCY CALCULATION
Document No. Pekerjaan Engineering, Procurement & Rev. : 2
LREF-00-VDR/CSP4-CAL-60- Construction (EPC) Proyek Pembangunan Sheet No.
0001-A4 Terminal LPG Refrigerated 4 of 44
TT-2032A ........................................................................................................ 29
TT-2032B ........................................................................................................ 30
TT-2053 .......................................................................................................... 31
TT-2054 .......................................................................................................... 32
TT-2058 .......................................................................................................... 33
TT-2071 .......................................................................................................... 34
TT-2080A ........................................................................................................ 35
TT-2080B ........................................................................................................ 36
TT-2081A ........................................................................................................ 37
TT-2081B ........................................................................................................ 38
TT-2081C ........................................................................................................ 39
TT-2082A ........................................................................................................ 40
TT-2082B ........................................................................................................ 41
TT-6007 .......................................................................................................... 42
TT-6041 .......................................................................................................... 43
TT-7041 .......................................................................................................... 44
Thermowell Calculation Report
This report is only valid with respect to thermowells produced and supplied by Emerson Automation Solutions in accordance with our exacting quality standards.
Customer Data
Company Name: PT Control Systems Arena Para Nusa Project Name: Pekerjaan EPC
Requestor Name: Insan Gaufuan Customer Drawing:
Analyst: Nesmar Noble Thermowell Model Code: 114CM0265PAC2SC060AQ5Q8R21XW
Reviewer: Customer Purchase Order:
Emerson Sales Order: Emerson Sales Order Line: Preliminary Report
Other Information / Notes: Max tip thickness = 7.9mm; Complete Project Name: Pekerjaan EPC Proyek Pembangunan Terminal LPG Refrigerated Tj Sekong
Process Data
Tag Name: TT-1021 Dynamic Fluid Viscosity (μ): 0.0068 [cP]
Process Fluid Velocity (V): 8.91 [m/s] Pressure (P): 0.11 [Kg/cm2-g] (1.14 [Kg/cm2-a])
Thermowell Dimensions
Mounting Configuration: RF-Flanged-Partial Penetration Weld
Process Connection: 2" Class 150
Stem Material: ASTM A 479 GR 316/316L
Stem Style: Tapered Shank
Root Diameter (A): 26.5 [mm]
Tip Diameter (B): 18 [mm]
Bore Diameter (d): 6.6 [mm]
Fillet Radius at Root (b): 4 [mm]
Fillet Radius at Base of Step (bs): Not Applicable
Unsupported Length (L): 265 [mm]
Reduced Diameter Length (Ls): Not Applicable
Minimum Tip Thickness (t): 6.4 [mm] (Not representative of tip allowance)
Protruding Length (PL): 54.32 [mm] (27% of Pipe ID) Representation of Thermowell Dimensions
Von Mises Stress Limit: 2.07e+08 [Pa] Steady State Stress at V (Smax): 1.37e+05 [Pa]
Material Density (ρm): 8030 [kg/m3] Cyclic Stress at VIR (So, max): Not Applicable
Dynamic Stress at V (So, max): Not Applicable (Reduced Diameter)
Frequency
Scruton Number (Nsc): 14.98 Max Allowable Stem Pressure (Pc): 5.49e+07 [Pa]
Frequency Limit: 0.8 Max Allowable Tip Pressure (Pt): 9.98e+08 [Pa]
In-situ Natural Freq (fnc): 304.2 [Hz]
Strouhal Frequency (fs): 93.2 [Hz]
Frequency Ratio (fs/fnc): 0.31
Thermowell Calculation Tool, Software Version: TCTP2_R_2.6.00 Form Rev P 10 May 2017
Thermowell Calculation Report
This report is only valid with respect to thermowells produced and supplied by Emerson Automation Solutions in accordance with our exacting quality standards.
Customer Data
Company Name: PT Control Systems Arena Para Nusa Project Name: Pekerjaan EPC
Requestor Name: Insan Gaufuan Customer Drawing:
Analyst: Nesmar Noble Thermowell Model Code: 114CM0265PAC2SC060AQ5Q8R21XW
Reviewer: Customer Purchase Order:
Emerson Sales Order: Emerson Sales Order Line: Preliminary Report
Other Information / Notes: Max tip thickness = 7.9mm; Complete Project Name: Pekerjaan EPC Proyek Pembangunan Terminal LPG Refrigerated Tj Sekong
Process Data
Tag Name: TT-1024 Dynamic Fluid Viscosity (μ): 0.0068 [cP]
Process Fluid Velocity (V): 7.7 [m/s] Pressure (P): 0.36 [Kg/cm2-g] (1.39 [Kg/cm2-a])
Thermowell Dimensions
Mounting Configuration: RF-Flanged-Partial Penetration Weld
Process Connection: 2" Class 150
Stem Material: ASTM A 479 GR 316/316L
Stem Style: Tapered Shank
Root Diameter (A): 26.5 [mm]
Tip Diameter (B): 18 [mm]
Bore Diameter (d): 6.6 [mm]
Fillet Radius at Root (b): 4 [mm]
Fillet Radius at Base of Step (bs): Not Applicable
Unsupported Length (L): 265 [mm]
Reduced Diameter Length (Ls): Not Applicable
Minimum Tip Thickness (t): 6.4 [mm] (Not representative of tip allowance)
Protruding Length (PL): 54.32 [mm] (27% of Pipe ID) Representation of Thermowell Dimensions
Von Mises Stress Limit: 2.07e+08 [Pa] Steady State Stress at V (Smax): 1.58e+05 [Pa]
Material Density (ρm): 8030 [kg/m3] Cyclic Stress at VIR (So, max): Not Applicable
Dynamic Stress at V (So, max): Not Applicable (Reduced Diameter)
Frequency
Scruton Number (Nsc): 14.98 Max Allowable Stem Pressure (Pc): 5.49e+07 [Pa]
Frequency Limit: 0.8 Max Allowable Tip Pressure (Pt): 9.98e+08 [Pa]
In-situ Natural Freq (fnc): 304.2 [Hz]
Strouhal Frequency (fs): 80.8 [Hz]
Frequency Ratio (fs/fnc): 0.27
Thermowell Calculation Tool, Software Version: TCTP2_R_2.6.00 Form Rev P 10 May 2017
Thermowell Calculation Report
This report is only valid with respect to thermowells produced and supplied by Emerson Automation Solutions in accordance with our exacting quality standards.
Customer Data
Company Name: PT Control Systems Arena Para Nusa Project Name: Pekerjaan EPC
Requestor Name: Insan Gaufuan Customer Drawing:
Analyst: Nesmar Noble Thermowell Model Code: 114CM0265PAC2SC060AQ5Q8R21XW
Reviewer: Customer Purchase Order:
Emerson Sales Order: Emerson Sales Order Line: Preliminary Report
Other Information / Notes: Max tip thickness = 7.9mm; Complete Project Name: Pekerjaan EPC Proyek Pembangunan Terminal LPG Refrigerated Tj Sekong
Process Data
Tag Name: TT-1031 Dynamic Fluid Viscosity (μ): 0.0068 [cP]
Process Fluid Velocity (V): 10.04 [m/s] Pressure (P): 0.11 [Kg/cm2-g] (1.14 [Kg/cm2-a])
Thermowell Dimensions
Mounting Configuration: RF-Flanged-Partial Penetration Weld
Process Connection: 2" Class 150
Stem Material: ASTM A 479 GR 316/316L
Stem Style: Tapered Shank
Root Diameter (A): 26.5 [mm]
Tip Diameter (B): 18 [mm]
Bore Diameter (d): 6.6 [mm]
Fillet Radius at Root (b): 4 [mm]
Fillet Radius at Base of Step (bs): Not Applicable
Unsupported Length (L): 265 [mm]
Reduced Diameter Length (Ls): Not Applicable
Minimum Tip Thickness (t): 6.4 [mm] (Not representative of tip allowance)
Protruding Length (PL): 54.32 [mm] (27% of Pipe ID) Representation of Thermowell Dimensions
Von Mises Stress Limit: 2.02e+08 [Pa] Steady State Stress at V (Smax): 1.45e+05 [Pa]
Material Density (ρm): 8030 [kg/m3] Cyclic Stress at VIR (So, max): Not Applicable
Dynamic Stress at V (So, max): Not Applicable (Reduced Diameter)
Frequency
Scruton Number (Nsc): 12.75 Max Allowable Stem Pressure (Pc): 5.35e+07 [Pa]
Frequency Limit: 0.8 Max Allowable Tip Pressure (Pt): 9.72e+08 [Pa]
In-situ Natural Freq (fnc): 302.2 [Hz]
Strouhal Frequency (fs): 104.9 [Hz]
Frequency Ratio (fs/fnc): 0.35
Thermowell Calculation Tool, Software Version: TCTP2_R_2.6.00 Form Rev P 10 May 2017
Thermowell Calculation Report
This report is only valid with respect to thermowells produced and supplied by Emerson Automation Solutions in accordance with our exacting quality standards.
Customer Data
Company Name: PT Control Systems Arena Para Nusa Project Name: Pekerjaan EPC
Requestor Name: Insan Gaufuan Customer Drawing:
Analyst: Nesmar Noble Thermowell Model Code: 114CM0265PAC2SC060AQ5Q8R21XW
Reviewer: Customer Purchase Order:
Emerson Sales Order: Emerson Sales Order Line: Preliminary Report
Other Information / Notes: Max tip thickness = 7.9mm; Complete Project Name: Pekerjaan EPC Proyek Pembangunan Terminal LPG Refrigerated Tj Sekong
Process Data
Tag Name: TT-1034 Dynamic Fluid Viscosity (μ): 0.0068 [cP]
Process Fluid Velocity (V): 8.33 [m/s] Pressure (P): 0.38 [Kg/cm2-g] (1.41 [Kg/cm2-a])
Thermowell Dimensions
Mounting Configuration: RF-Flanged-Partial Penetration Weld
Process Connection: 2" Class 150
Stem Material: ASTM A 479 GR 316/316L
Stem Style: Tapered Shank
Root Diameter (A): 26.5 [mm]
Tip Diameter (B): 18 [mm]
Bore Diameter (d): 6.6 [mm]
Fillet Radius at Root (b): 4 [mm]
Fillet Radius at Base of Step (bs): Not Applicable
Unsupported Length (L): 265 [mm]
Reduced Diameter Length (Ls): Not Applicable
Minimum Tip Thickness (t): 6.4 [mm] (Not representative of tip allowance)
Protruding Length (PL): 54.32 [mm] (27% of Pipe ID) Representation of Thermowell Dimensions
Von Mises Stress Limit: 2.02e+08 [Pa] Steady State Stress at V (Smax): 1.65e+05 [Pa]
Material Density (ρm): 8030 [kg/m3] Cyclic Stress at VIR (So, max): Not Applicable
Dynamic Stress at V (So, max): Not Applicable (Reduced Diameter)
Frequency
Scruton Number (Nsc): 12.75 Max Allowable Stem Pressure (Pc): 5.35e+07 [Pa]
Frequency Limit: 0.8 Max Allowable Tip Pressure (Pt): 9.72e+08 [Pa]
In-situ Natural Freq (fnc): 302.2 [Hz]
Strouhal Frequency (fs): 87.0 [Hz]
Frequency Ratio (fs/fnc): 0.29
Thermowell Calculation Tool, Software Version: TCTP2_R_2.6.00 Form Rev P 10 May 2017
Thermowell Calculation Report
This report is only valid with respect to thermowells produced and supplied by Emerson Automation Solutions in accordance with our exacting quality standards.
Customer Data
Company Name: PT Control Systems Arena Para Nusa Project Name: Pekerjaan EPC
Requestor Name: Insan Gaufuan Customer Drawing:
Analyst: Nesmar Noble Thermowell Model Code: 114CM0265PAC2SC060AQ5Q8R21XW
Reviewer: Customer Purchase Order:
Emerson Sales Order: Emerson Sales Order Line: Preliminary Report
Other Information / Notes: Max tip thickness = 7.9mm; Complete Project Name: Pekerjaan EPC Proyek Pembangunan Terminal LPG Refrigerated Tj Sekong
Process Data
Tag Name: TT-1036 Dynamic Fluid Viscosity (μ): 0.0068 [cP]
Process Fluid Velocity (V): 9 [m/s] Pressure (P): 0.11 [Kg/cm2-g] (1.14 [Kg/cm2-a])
Thermowell Dimensions
Mounting Configuration: RF-Flanged-Partial Penetration Weld
Process Connection: 2" Class 150
Stem Material: ASTM A 479 GR 316/316L
Stem Style: Tapered Shank
Root Diameter (A): 26.5 [mm]
Tip Diameter (B): 18 [mm]
Bore Diameter (d): 6.6 [mm]
Fillet Radius at Root (b): 4 [mm]
Fillet Radius at Base of Step (bs): Not Applicable
Unsupported Length (L): 265 [mm]
Reduced Diameter Length (Ls): Not Applicable
Minimum Tip Thickness (t): 6.4 [mm] (Not representative of tip allowance)
Protruding Length (PL): 54.32 [mm] (27% of Pipe ID) Representation of Thermowell Dimensions
Von Mises Stress Limit: 2.07e+08 [Pa] Steady State Stress at V (Smax): 1.37e+05 [Pa]
Material Density (ρm): 8030 [kg/m3] Cyclic Stress at VIR (So, max): Not Applicable
Dynamic Stress at V (So, max): Not Applicable (Reduced Diameter)
Frequency
Scruton Number (Nsc): 14.98 Max Allowable Stem Pressure (Pc): 5.49e+07 [Pa]
Frequency Limit: 0.8 Max Allowable Tip Pressure (Pt): 9.98e+08 [Pa]
In-situ Natural Freq (fnc): 304.2 [Hz]
Strouhal Frequency (fs): 94.2 [Hz]
Frequency Ratio (fs/fnc): 0.31
Thermowell Calculation Tool, Software Version: TCTP2_R_2.6.00 Form Rev P 10 May 2017
Thermowell Calculation Report
This report is only valid with respect to thermowells produced and supplied by Emerson Automation Solutions in accordance with our exacting quality standards.
Customer Data
Company Name: PT Control Systems Arena Para Nusa Project Name: Pekerjaan EPC
Requestor Name: Insan Gaufuan Customer Drawing:
Analyst: Nesmar Noble Thermowell Model Code: 114CM0265PAC2SC060AQ5Q8R21XW
Reviewer: Customer Purchase Order:
Emerson Sales Order: Emerson Sales Order Line: Preliminary Report
Other Information / Notes: Max tip thickness = 7.9mm; Complete Project Name: Pekerjaan EPC Proyek Pembangunan Terminal LPG Refrigerated Tj Sekong
Process Data
Tag Name: TT-1039 Dynamic Fluid Viscosity (μ): 0.0068 [cP]
Process Fluid Velocity (V): 7.88 [m/s] Pressure (P): 0.36 [Kg/cm2-g] (1.39 [Kg/cm2-a])
Thermowell Dimensions
Mounting Configuration: RF-Flanged-Partial Penetration Weld
Process Connection: 2" Class 150
Stem Material: ASTM A 479 GR 316/316L
Stem Style: Tapered Shank
Root Diameter (A): 26.5 [mm]
Tip Diameter (B): 18 [mm]
Bore Diameter (d): 6.6 [mm]
Fillet Radius at Root (b): 4 [mm]
Fillet Radius at Base of Step (bs): Not Applicable
Unsupported Length (L): 265 [mm]
Reduced Diameter Length (Ls): Not Applicable
Minimum Tip Thickness (t): 6.4 [mm] (Not representative of tip allowance)
Protruding Length (PL): 54.32 [mm] (27% of Pipe ID) Representation of Thermowell Dimensions
Von Mises Stress Limit: 2.07e+08 [Pa] Steady State Stress at V (Smax): 1.59e+05 [Pa]
Material Density (ρm): 8030 [kg/m3] Cyclic Stress at VIR (So, max): Not Applicable
Dynamic Stress at V (So, max): Not Applicable (Reduced Diameter)
Frequency
Scruton Number (Nsc): 14.98 Max Allowable Stem Pressure (Pc): 5.49e+07 [Pa]
Frequency Limit: 0.8 Max Allowable Tip Pressure (Pt): 9.98e+08 [Pa]
In-situ Natural Freq (fnc): 304.2 [Hz]
Strouhal Frequency (fs): 82.6 [Hz]
Frequency Ratio (fs/fnc): 0.27
Thermowell Calculation Tool, Software Version: TCTP2_R_2.6.00 Form Rev P 10 May 2017
Thermowell Calculation Report
This report is only valid with respect to thermowells produced and supplied by Emerson Automation Solutions in accordance with our exacting quality standards.
Customer Data
Company Name: PT Control Systems Arena Para Nusa Project Name: Pekerjaan EPC
Requestor Name: Insan Gaufuan Customer Drawing:
Analyst: Nesmar Noble Thermowell Model Code: 114CM0265PAC2SC060AQ5Q8R21XW
Reviewer: Customer Purchase Order:
Emerson Sales Order: Emerson Sales Order Line: Preliminary Report
Other Information / Notes: Max tip thickness = 7.9mm; Complete Project Name: Pekerjaan EPC Proyek Pembangunan Terminal LPG Refrigerated Tj Sekong
Process Data
Tag Name: TT-1061 Dynamic Fluid Viscosity (μ): 0.0068 [cP]
Process Fluid Velocity (V): 9 [m/s] Pressure (P): 0.11 [Kg/cm2-g] (1.14 [Kg/cm2-a])
Thermowell Dimensions
Mounting Configuration: RF-Flanged-Partial Penetration Weld
Process Connection: 2" Class 150
Stem Material: ASTM A 479 GR 316/316L
Stem Style: Tapered Shank
Root Diameter (A): 26.5 [mm]
Tip Diameter (B): 18 [mm]
Bore Diameter (d): 6.6 [mm]
Fillet Radius at Root (b): 4 [mm]
Fillet Radius at Base of Step (bs): Not Applicable
Unsupported Length (L): 265 [mm]
Reduced Diameter Length (Ls): Not Applicable
Minimum Tip Thickness (t): 6.4 [mm] (Not representative of tip allowance)
Protruding Length (PL): 54.32 [mm] (27% of Pipe ID) Representation of Thermowell Dimensions
Von Mises Stress Limit: 2.07e+08 [Pa] Steady State Stress at V (Smax): 1.37e+05 [Pa]
Material Density (ρm): 8030 [kg/m3] Cyclic Stress at VIR (So, max): Not Applicable
Dynamic Stress at V (So, max): Not Applicable (Reduced Diameter)
Frequency
Scruton Number (Nsc): 14.98 Max Allowable Stem Pressure (Pc): 5.49e+07 [Pa]
Frequency Limit: 0.8 Max Allowable Tip Pressure (Pt): 9.98e+08 [Pa]
In-situ Natural Freq (fnc): 304.2 [Hz]
Strouhal Frequency (fs): 94.2 [Hz]
Frequency Ratio (fs/fnc): 0.31
Thermowell Calculation Tool, Software Version: TCTP2_R_2.6.00 Form Rev P 10 May 2017
Thermowell Calculation Report
This report is only valid with respect to thermowells produced and supplied by Emerson Automation Solutions in accordance with our exacting quality standards.
Customer Data
Company Name: PT Control Systems Arena Para Nusa Project Name: Pekerjaan EPC
Requestor Name: Insan Gaufuan Customer Drawing:
Analyst: Nesmar Noble Thermowell Model Code: 114CM0265PAC2SC060AQ5Q8R21XW
Reviewer: Customer Purchase Order:
Emerson Sales Order: Emerson Sales Order Line: Preliminary Report
Other Information / Notes: Max tip thickness = 7.9mm; Complete Project Name: Pekerjaan EPC Proyek Pembangunan Terminal LPG Refrigerated Tj Sekong
Process Data
Tag Name: TT-1064 Dynamic Fluid Viscosity (μ): 0.0068 [cP]
Process Fluid Velocity (V): 7.88 [m/s] Pressure (P): 0.36 [Kg/cm2-g] (1.39 [Kg/cm2-a])
Thermowell Dimensions
Mounting Configuration: RF-Flanged-Partial Penetration Weld
Process Connection: 2" Class 150
Stem Material: ASTM A 479 GR 316/316L
Stem Style: Tapered Shank
Root Diameter (A): 26.5 [mm]
Tip Diameter (B): 18 [mm]
Bore Diameter (d): 6.6 [mm]
Fillet Radius at Root (b): 4 [mm]
Fillet Radius at Base of Step (bs): Not Applicable
Unsupported Length (L): 265 [mm]
Reduced Diameter Length (Ls): Not Applicable
Minimum Tip Thickness (t): 6.4 [mm] (Not representative of tip allowance)
Protruding Length (PL): 54.32 [mm] (27% of Pipe ID) Representation of Thermowell Dimensions
Von Mises Stress Limit: 2.07e+08 [Pa] Steady State Stress at V (Smax): 1.59e+05 [Pa]
Material Density (ρm): 8030 [kg/m3] Cyclic Stress at VIR (So, max): Not Applicable
Dynamic Stress at V (So, max): Not Applicable (Reduced Diameter)
Frequency
Scruton Number (Nsc): 14.98 Max Allowable Stem Pressure (Pc): 5.49e+07 [Pa]
Frequency Limit: 0.8 Max Allowable Tip Pressure (Pt): 9.98e+08 [Pa]
In-situ Natural Freq (fnc): 304.2 [Hz]
Strouhal Frequency (fs): 82.6 [Hz]
Frequency Ratio (fs/fnc): 0.27
Thermowell Calculation Tool, Software Version: TCTP2_R_2.6.00 Form Rev P 10 May 2017
Thermowell Calculation Report
This report is only valid with respect to thermowells produced and supplied by Emerson Automation Solutions in accordance with our exacting quality standards.
Customer Data
Company Name: PT Control Systems Arena Para Nusa Project Name: Pekerjaan EPC
Requestor Name: Insan Gaufuan Customer Drawing:
Analyst: Nesmar Noble Thermowell Model Code: 114CM0265PAC2SC060AQ5Q8R21XW
Reviewer: Customer Purchase Order:
Emerson Sales Order: Emerson Sales Order Line: Preliminary Report
Other Information / Notes: Max tip thickness = 7.9mm; Complete Project Name: Pekerjaan EPC Proyek Pembangunan Terminal LPG Refrigerated Tj Sekong
Process Data
Tag Name: TT-1071 Dynamic Fluid Viscosity (μ): 0.0068 [cP]
Process Fluid Velocity (V): 10.02 [m/s] Pressure (P): 0.11 [Kg/cm2-g] (1.14 [Kg/cm2-a])
Thermowell Dimensions
Mounting Configuration: RF-Flanged-Partial Penetration Weld
Process Connection: 2" Class 150
Stem Material: ASTM A 479 GR 316/316L
Stem Style: Tapered Shank
Root Diameter (A): 26.5 [mm]
Tip Diameter (B): 18 [mm]
Bore Diameter (d): 6.6 [mm]
Fillet Radius at Root (b): 4 [mm]
Fillet Radius at Base of Step (bs): Not Applicable
Unsupported Length (L): 265 [mm]
Reduced Diameter Length (Ls): Not Applicable
Minimum Tip Thickness (t): 6.4 [mm] (Not representative of tip allowance)
Protruding Length (PL): 54.32 [mm] (27% of Pipe ID) Representation of Thermowell Dimensions
Von Mises Stress Limit: 2.02e+08 [Pa] Steady State Stress at V (Smax): 1.45e+05 [Pa]
Material Density (ρm): 8030 [kg/m3] Cyclic Stress at VIR (So, max): Not Applicable
Dynamic Stress at V (So, max): Not Applicable (Reduced Diameter)
Frequency
Scruton Number (Nsc): 12.75 Max Allowable Stem Pressure (Pc): 5.35e+07 [Pa]
Frequency Limit: 0.8 Max Allowable Tip Pressure (Pt): 9.72e+08 [Pa]
In-situ Natural Freq (fnc): 302.2 [Hz]
Strouhal Frequency (fs): 104.7 [Hz]
Frequency Ratio (fs/fnc): 0.35
Thermowell Calculation Tool, Software Version: TCTP2_R_2.6.00 Form Rev P 10 May 2017
Thermowell Calculation Report
This report is only valid with respect to thermowells produced and supplied by Emerson Automation Solutions in accordance with our exacting quality standards.
Customer Data
Company Name: PT Control Systems Arena Para Nusa Project Name: Pekerjaan EPC
Requestor Name: Insan Gaufuan Customer Drawing:
Analyst: Nesmar Noble Thermowell Model Code: 114CM0265PAC2SC060AQ5Q8R21XW
Reviewer: Customer Purchase Order:
Emerson Sales Order: Emerson Sales Order Line: Preliminary Report
Other Information / Notes: Max tip thickness = 7.9mm; Complete Project Name: Pekerjaan EPC Proyek Pembangunan Terminal LPG Refrigerated Tj Sekong
Process Data
Tag Name: TT-1074 Dynamic Fluid Viscosity (μ): 0.0068 [cP]
Process Fluid Velocity (V): 8.44 [m/s] Pressure (P): 0.37 [Kg/cm2-g] (1.40 [Kg/cm2-a])
Thermowell Dimensions
Mounting Configuration: RF-Flanged-Partial Penetration Weld
Process Connection: 2" Class 150
Stem Material: ASTM A 479 GR 316/316L
Stem Style: Tapered Shank
Root Diameter (A): 26.5 [mm]
Tip Diameter (B): 18 [mm]
Bore Diameter (d): 6.6 [mm]
Fillet Radius at Root (b): 4 [mm]
Fillet Radius at Base of Step (bs): Not Applicable
Unsupported Length (L): 265 [mm]
Reduced Diameter Length (Ls): Not Applicable
Minimum Tip Thickness (t): 6.4 [mm] (Not representative of tip allowance)
Protruding Length (PL): 54.32 [mm] (27% of Pipe ID) Representation of Thermowell Dimensions
Von Mises Stress Limit: 2.02e+08 [Pa] Steady State Stress at V (Smax): 1.65e+05 [Pa]
Material Density (ρm): 8030 [kg/m3] Cyclic Stress at VIR (So, max): Not Applicable
Dynamic Stress at V (So, max): Not Applicable (Reduced Diameter)
Frequency
Scruton Number (Nsc): 12.75 Max Allowable Stem Pressure (Pc): 5.35e+07 [Pa]
Frequency Limit: 0.8 Max Allowable Tip Pressure (Pt): 9.72e+08 [Pa]
In-situ Natural Freq (fnc): 302.2 [Hz]
Strouhal Frequency (fs): 88.2 [Hz]
Frequency Ratio (fs/fnc): 0.29
Thermowell Calculation Tool, Software Version: TCTP2_R_2.6.00 Form Rev P 10 May 2017
Thermowell Calculation Report
This report is only valid with respect to thermowells produced and supplied by Emerson Automation Solutions in accordance with our exacting quality standards.
Customer Data
Company Name: PT Control Systems Arena Para Nusa Project Name: Pekerjaan EPC
Requestor Name: Insan Gaufuan Customer Drawing:
Analyst: Nesmar Noble Thermowell Model Code: 114CM0265PAC2SC060AQ5Q8R21XW
Reviewer: Customer Purchase Order:
Emerson Sales Order: Emerson Sales Order Line: Preliminary Report
Other Information / Notes: Max tip thickness = 7.9mm; Complete Project Name: Pekerjaan EPC Proyek Pembangunan Terminal LPG Refrigerated Tj Sekong
Process Data
Tag Name: TT-1086 Dynamic Fluid Viscosity (μ): 0.0068 [cP]
Process Fluid Velocity (V): 10.02 [m/s] Pressure (P): 0.11 [Kg/cm2-g] (1.14 [Kg/cm2-a])
Thermowell Dimensions
Mounting Configuration: RF-Flanged-Partial Penetration Weld
Process Connection: 2" Class 150
Stem Material: ASTM A 479 GR 316/316L
Stem Style: Tapered Shank
Root Diameter (A): 26.5 [mm]
Tip Diameter (B): 18 [mm]
Bore Diameter (d): 6.6 [mm]
Fillet Radius at Root (b): 4 [mm]
Fillet Radius at Base of Step (bs): Not Applicable
Unsupported Length (L): 265 [mm]
Reduced Diameter Length (Ls): Not Applicable
Minimum Tip Thickness (t): 6.4 [mm] (Not representative of tip allowance)
Protruding Length (PL): 54.32 [mm] (27% of Pipe ID) Representation of Thermowell Dimensions
Von Mises Stress Limit: 2.02e+08 [Pa] Steady State Stress at V (Smax): 1.45e+05 [Pa]
Material Density (ρm): 8030 [kg/m3] Cyclic Stress at VIR (So, max): Not Applicable
Dynamic Stress at V (So, max): Not Applicable (Reduced Diameter)
Frequency
Scruton Number (Nsc): 12.75 Max Allowable Stem Pressure (Pc): 5.35e+07 [Pa]
Frequency Limit: 0.8 Max Allowable Tip Pressure (Pt): 9.72e+08 [Pa]
In-situ Natural Freq (fnc): 302.2 [Hz]
Strouhal Frequency (fs): 104.7 [Hz]
Frequency Ratio (fs/fnc): 0.35
Thermowell Calculation Tool, Software Version: TCTP2_R_2.6.00 Form Rev P 10 May 2017
Thermowell Calculation Report
This report is only valid with respect to thermowells produced and supplied by Emerson Automation Solutions in accordance with our exacting quality standards.
Customer Data
Company Name: PT Control Systems Arena Para Nusa Project Name: Pekerjaan EPC
Requestor Name: Insan Gaufuan Customer Drawing:
Analyst: Nesmar Noble Thermowell Model Code: 114CM0265PAC2SC060AQ5Q8R21XW
Reviewer: Customer Purchase Order:
Emerson Sales Order: Emerson Sales Order Line: Preliminary Report
Other Information / Notes: Max tip thickness = 7.9mm; Complete Project Name: Pekerjaan EPC Proyek Pembangunan Terminal LPG Refrigerated Tj Sekong
Process Data
Tag Name: TT-1089 Dynamic Fluid Viscosity (μ): 0.0068 [cP]
Process Fluid Velocity (V): 8.44 [m/s] Pressure (P): 0.37 [Kg/cm2-g] (1.40 [Kg/cm2-a])
Thermowell Dimensions
Mounting Configuration: RF-Flanged-Partial Penetration Weld
Process Connection: 2" Class 150
Stem Material: ASTM A 479 GR 316/316L
Stem Style: Tapered Shank
Root Diameter (A): 26.5 [mm]
Tip Diameter (B): 18 [mm]
Bore Diameter (d): 6.6 [mm]
Fillet Radius at Root (b): 4 [mm]
Fillet Radius at Base of Step (bs): Not Applicable
Unsupported Length (L): 265 [mm]
Reduced Diameter Length (Ls): Not Applicable
Minimum Tip Thickness (t): 6.4 [mm] (Not representative of tip allowance)
Protruding Length (PL): 54.32 [mm] (27% of Pipe ID) Representation of Thermowell Dimensions
Von Mises Stress Limit: 2.02e+08 [Pa] Steady State Stress at V (Smax): 1.65e+05 [Pa]
Material Density (ρm): 8030 [kg/m3] Cyclic Stress at VIR (So, max): Not Applicable
Dynamic Stress at V (So, max): Not Applicable (Reduced Diameter)
Frequency
Scruton Number (Nsc): 12.75 Max Allowable Stem Pressure (Pc): 5.35e+07 [Pa]
Frequency Limit: 0.8 Max Allowable Tip Pressure (Pt): 9.72e+08 [Pa]
In-situ Natural Freq (fnc): 302.2 [Hz]
Strouhal Frequency (fs): 88.2 [Hz]
Frequency Ratio (fs/fnc): 0.29
Thermowell Calculation Tool, Software Version: TCTP2_R_2.6.00 Form Rev P 10 May 2017
Thermowell Calculation Report
This report is only valid with respect to thermowells produced and supplied by Emerson Automation Solutions in accordance with our exacting quality standards.
Customer Data
Company Name: PT Control Systems Arena Para Nusa Project Name: Pekerjaan EPC
Requestor Name: Insan Gaufuan Customer Drawing:
Analyst: Nesmar Noble Thermowell Model Code: 114CM0300PAC2SC060AQ5Q8R21XW
Reviewer: Customer Purchase Order:
Emerson Sales Order: Emerson Sales Order Line: Preliminary Report
Other Information / Notes: Max tip thickness = 7.9mm; Complete Project Name: Pekerjaan EPC Proyek Pembangunan Terminal LPG Refrigerated Tj Sekong
Process Data
Tag Name: TT-2003 Dynamic Fluid Viscosity (μ): 0.0068 [cP]
Process Fluid Velocity (V): 4.9 [m/s] Pressure (P): 0.44 [Kg/cm2-g] (1.47 [Kg/cm2-a])
Thermowell Dimensions
Mounting Configuration: RF-Flanged-Partial Penetration Weld
Process Connection: 2" Class 150
Stem Material: ASTM A 479 GR 316/316L
Stem Style: Tapered Shank
Root Diameter (A): 26.5 [mm]
Tip Diameter (B): 18 [mm]
Bore Diameter (d): 6.6 [mm]
Fillet Radius at Root (b): 4 [mm]
Fillet Radius at Base of Step (bs): Not Applicable
Unsupported Length (L): 300 [mm]
Reduced Diameter Length (Ls): Not Applicable
Minimum Tip Thickness (t): 6.4 [mm] (Not representative of tip allowance)
Protruding Length (PL): 88.23 [mm] (35% of Pipe ID) Representation of Thermowell Dimensions
Von Mises Stress Limit: 2.07e+08 [Pa] Steady State Stress at V (Smax): 1.63e+05 [Pa]
Material Density (ρm): 8030 [kg/m3] Cyclic Stress at VIR (So, max): Not Applicable
Dynamic Stress at V (So, max): Not Applicable (Reduced Diameter)
Frequency
Scruton Number (Nsc): 14.98 Max Allowable Stem Pressure (Pc): 5.49e+07 [Pa]
Frequency Limit: 0.8 Max Allowable Tip Pressure (Pt): 9.98e+08 [Pa]
In-situ Natural Freq (fnc): 238.7 [Hz]
Strouhal Frequency (fs): 52.0 [Hz]
Frequency Ratio (fs/fnc): 0.22
Thermowell Calculation Tool, Software Version: TCTP2_R_2.6.00 Form Rev P 10 May 2017
Thermowell Calculation Report
This report is only valid with respect to thermowells produced and supplied by Emerson Automation Solutions in accordance with our exacting quality standards.
Customer Data
Company Name: PT Control Systems Arena Para Nusa Project Name: Pekerjaan EPC
Requestor Name: Insan Gaufuan Customer Drawing:
Analyst: Nesmar Noble Thermowell Model Code: 114CM0435PAC2SC060AQ5Q8R21XW
Reviewer: Customer Purchase Order:
Emerson Sales Order: Emerson Sales Order Line: Preliminary Report
Other Information / Notes: Max tip thickness = 7.9mm; Complete Project Name: Pekerjaan EPC Proyek Pembangunan Terminal LPG Refrigerated Tj Sekong
Process Data
Tag Name: TT-2004 Dynamic Fluid Viscosity (μ): 0.0068 [cP]
Process Fluid Velocity (V): 9.65 [m/s] Pressure (P): 0.09 [Kg/cm2-g] (1.12 [Kg/cm2-a])
Thermowell Dimensions
Mounting Configuration: RF-Flanged-Partial Penetration Weld
Process Connection: 2" Class 150
Stem Material: ASTM A 479 GR 316/316L
Stem Style: Tapered Shank
Root Diameter (A): 26.5 [mm]
Tip Diameter (B): 18 [mm]
Bore Diameter (d): 6.6 [mm]
Fillet Radius at Root (b): 4 [mm]
Fillet Radius at Base of Step (bs): Not Applicable
Unsupported Length (L): 410 [mm]
Reduced Diameter Length (Ls): Not Applicable
Minimum Tip Thickness (t): 6.4 [mm] (Not representative of tip allowance)
Protruding Length (PL): 197.97 [mm] (45% of Pipe ID) Representation of Thermowell Dimensions
Von Mises Stress Limit: 2.07e+08 [Pa] Steady State Stress at V (Smax): 2.18e+05 [Pa]
Material Density (ρm): 8030 [kg/m3] Cyclic Stress at VIR (So, max): Not Applicable
Dynamic Stress at V (So, max): Not Applicable (Reduced Diameter)
Frequency
Scruton Number (Nsc): 14.98 Max Allowable Stem Pressure (Pc): 5.49e+07 [Pa]
Frequency Limit: 0.8 Max Allowable Tip Pressure (Pt): 9.98e+08 [Pa]
In-situ Natural Freq (fnc): 129.3 [Hz]
Strouhal Frequency (fs): 100.8 [Hz]
Frequency Ratio (fs/fnc): 0.78
Thermowell Calculation Tool, Software Version: TCTP2_R_2.6.00 Form Rev P 10 May 2017
Thermowell Calculation Report
This report is only valid with respect to thermowells produced and supplied by Emerson Automation Solutions in accordance with our exacting quality standards.
Customer Data
Company Name: PT Control Systems Arena Para Nusa Project Name: Pekerjaan EPC
Requestor Name: Insan Gaufuan Customer Drawing:
Analyst: Nesmar Noble Thermowell Model Code:
Reviewer: Customer Purchase Order:
Emerson Sales Order: Emerson Sales Order Line: Preliminary Report
Other Information / Notes: Max tip thickness = 7.9mm; Complete Project Name: Pekerjaan EPC Proyek Pembangunan Terminal LPG Refrigerated Tj Sekong
Process Data
Tag Name: TT-2008 Dynamic Fluid Viscosity (μ): 0.0867 [cP]
Process Fluid Velocity (V): 0.31 [m/s] Pressure (P): 16 [Kg/cm2-g] (17.03 [Kg/cm2-a])
Thermowell Dimensions
Mounting Configuration: RF-Flanged-Partial Penetration Weld
Process Connection: 2" Class 300
Stem Material: ASTM A 479 GR 316/316L
Stem Style: Tapered Shank
Root Diameter (A): 26.5 [mm]
Tip Diameter (B): 18 [mm]
Bore Diameter (d): 6.6 [mm]
Fillet Radius at Root (b): 4 [mm]
Fillet Radius at Base of Step (bs): Not Applicable
Unsupported Length (L): 230 [mm]
Reduced Diameter Length (Ls): Not Applicable
Minimum Tip Thickness (t): 6.4 [mm] (Not representative of tip allowance)
Protruding Length (PL): 14.89 [mm] (10% of Pipe ID) Representation of Thermowell Dimensions
Von Mises Stress Limit: 1.97e+08 [Pa] Steady State Stress at V (Smax): 1.78e+06 [Pa]
Material Density (ρm): 8030 [kg/m3] Cyclic Stress at VIR (So, max): Not Applicable
Dynamic Stress at V (So, max): Not Applicable (Reduced Diameter)
Frequency
Scruton Number (Nsc): 0.07 Max Allowable Stem Pressure (Pc): 5.22e+07 [Pa]
Frequency Limit: 0.4 Max Allowable Tip Pressure (Pt): 9.50e+08 [Pa]
In-situ Natural Freq (fnc): 384.2 [Hz]
Strouhal Frequency (fs): 3.3 [Hz]
Frequency Ratio (fs/fnc): 0.01
Thermowell Calculation Tool, Software Version: TCTP2_R_2.6.00 Form Rev P 10 May 2017
Thermowell Calculation Report
This report is only valid with respect to thermowells produced and supplied by Emerson Automation Solutions in accordance with our exacting quality standards.
Customer Data
Company Name: PT Control Systems Arena Para Nusa Project Name: Pekerjaan EPC
Requestor Name: Insan Gaufuan Customer Drawing:
Analyst: Nesmar Noble Thermowell Model Code:
Reviewer: Customer Purchase Order:
Emerson Sales Order: Emerson Sales Order Line: Preliminary Report
Other Information / Notes: Max tip thickness = 7.9mm; Complete Project Name: Pekerjaan EPC Proyek Pembangunan Terminal LPG Refrigerated Tj Sekong
Process Data
Tag Name: TT-2021 Case 1 Dynamic Fluid Viscosity (μ): 0.1218 [cP]
Process Fluid Velocity (V): 3.79 [m/s] Pressure (P): 19.46 [Kg/cm2-g] (20.49 [Kg/cm2-a])
Thermowell Dimensions
Mounting Configuration: RF-Flanged-Partial Penetration Weld
Process Connection: 2" Class 300
Stem Material: ASTM A 479 GR 316/316L
Stem Style: Tapered Shank
Root Diameter (A): 26.5 [mm]
Tip Diameter (B): 18 [mm]
Bore Diameter (d): 6.6 [mm]
Fillet Radius at Root (b): 4 [mm]
Fillet Radius at Base of Step (bs): Not Applicable
Unsupported Length (L): 260 [mm]
Reduced Diameter Length (Ls): Not Applicable
Minimum Tip Thickness (t): 6.4 [mm] (Not representative of tip allowance)
Protruding Length (PL): 43.32 [mm] (21% of Pipe ID) Representation of Thermowell Dimensions
Von Mises Stress Limit: 2.07e+08 [Pa] Steady State Stress at V (Smax): 2.76e+06 [Pa]
Material Density (ρm): 8030 [kg/m3] Cyclic Stress at VIR (So, max): Not Applicable
Dynamic Stress at V (So, max): Not Applicable (Reduced Diameter)
Frequency
Scruton Number (Nsc): 0.06 Max Allowable Stem Pressure (Pc): 5.49e+07 [Pa]
Frequency Limit: 0.4 Max Allowable Tip Pressure (Pt): 9.98e+08 [Pa]
In-situ Natural Freq (fnc): 304.9 [Hz]
Strouhal Frequency (fs): 42.4 [Hz]
Frequency Ratio (fs/fnc): 0.14
Thermowell Calculation Tool, Software Version: TCTP2_R_2.6.00 Form Rev P 10 May 2017
Thermowell Calculation Report
This report is only valid with respect to thermowells produced and supplied by Emerson Automation Solutions in accordance with our exacting quality standards.
Customer Data
Company Name: PT Control Systems Arena Para Nusa Project Name: Pekerjaan EPC
Requestor Name: Insan Gaufuan Customer Drawing:
Analyst: Nesmar Noble Thermowell Model Code:
Reviewer: Customer Purchase Order:
Emerson Sales Order: Emerson Sales Order Line: Preliminary Report
Other Information / Notes: Max tip thickness = 7.9mm; Complete Project Name: Pekerjaan EPC Proyek Pembangunan Terminal LPG Refrigerated Tj Sekong
Process Data
Tag Name: TT-2021 Case 2 Dynamic Fluid Viscosity (μ): 0.1218 [cP]
Process Fluid Velocity (V): 3.79 [m/s] Pressure (P): 19.46 [Kg/cm2-g] (20.49 [Kg/cm2-a])
Thermowell Dimensions
Mounting Configuration: RF-Flanged-Partial Penetration Weld
Process Connection: 2" Class 300
Stem Material: ASTM A 479 GR 316/316L
Stem Style: Tapered Shank
Root Diameter (A): 26.5 [mm]
Tip Diameter (B): 18 [mm]
Bore Diameter (d): 6.6 [mm]
Fillet Radius at Root (b): 4 [mm]
Fillet Radius at Base of Step (bs): Not Applicable
Unsupported Length (L): 260 [mm]
Reduced Diameter Length (Ls): Not Applicable
Minimum Tip Thickness (t): 6.4 [mm] (Not representative of tip allowance)
Protruding Length (PL): 43.32 [mm] (21% of Pipe ID) Representation of Thermowell Dimensions
Von Mises Stress Limit: 2.02e+08 [Pa] Steady State Stress at V (Smax): 2.76e+06 [Pa]
Material Density (ρm): 8030 [kg/m3] Cyclic Stress at VIR (So, max): Not Applicable
Dynamic Stress at V (So, max): Not Applicable (Reduced Diameter)
Frequency
Scruton Number (Nsc): 0.06 Max Allowable Stem Pressure (Pc): 5.35e+07 [Pa]
Frequency Limit: 0.4 Max Allowable Tip Pressure (Pt): 9.72e+08 [Pa]
In-situ Natural Freq (fnc): 302.3 [Hz]
Strouhal Frequency (fs): 42.4 [Hz]
Frequency Ratio (fs/fnc): 0.14
Thermowell Calculation Tool, Software Version: TCTP2_R_2.6.00 Form Rev P 10 May 2017
Thermowell Calculation Report
This report is only valid with respect to thermowells produced and supplied by Emerson Automation Solutions in accordance with our exacting quality standards.
Customer Data
Company Name: PT Control Systems Arena Para Nusa Project Name: Pekerjaan EPC
Requestor Name: Insan Gaufuan Customer Drawing:
Analyst: Nesmar Noble Thermowell Model Code:
Reviewer: Customer Purchase Order:
Emerson Sales Order: Emerson Sales Order Line: Preliminary Report
Other Information / Notes: Max tip thickness = 7.9mm; Complete Project Name: Pekerjaan EPC Proyek Pembangunan Terminal LPG Refrigerated Tj Sekong
Process Data
Tag Name: TT-2023 Case 1 Dynamic Fluid Viscosity (μ): 0.1978 [cP]
Process Fluid Velocity (V): 2.84 [m/s] Pressure (P): 18.8 [Kg/cm2-g] (19.83 [Kg/cm2-a])
Thermowell Dimensions
Mounting Configuration: RF-Flanged-Partial Penetration Weld
Process Connection: 2" Class 300
Stem Material: ASTM A 479 GR 316/316L
Stem Style: Tapered Shank
Root Diameter (A): 26.5 [mm]
Tip Diameter (B): 18 [mm]
Bore Diameter (d): 6.6 [mm]
Fillet Radius at Root (b): 4 [mm]
Fillet Radius at Base of Step (bs): Not Applicable
Unsupported Length (L): 260 [mm]
Reduced Diameter Length (Ls): Not Applicable
Minimum Tip Thickness (t): 6.4 [mm] (Not representative of tip allowance)
Protruding Length (PL): 51.98 [mm] (51% of Pipe ID) Representation of Thermowell Dimensions
Von Mises Stress Limit: 2.07e+08 [Pa] Steady State Stress at V (Smax): 2.49e+06 [Pa]
Material Density (ρm): 8030 [kg/m3] Cyclic Stress at VIR (So, max): Not Applicable
Dynamic Stress at V (So, max): Not Applicable (Reduced Diameter)
Frequency
Scruton Number (Nsc): 0.06 Max Allowable Stem Pressure (Pc): 5.49e+07 [Pa]
Frequency Limit: 0.4 Max Allowable Tip Pressure (Pt): 9.98e+08 [Pa]
In-situ Natural Freq (fnc): 304.9 [Hz]
Strouhal Frequency (fs): 30.1 [Hz]
Frequency Ratio (fs/fnc): 0.10
Thermowell Calculation Tool, Software Version: TCTP2_R_2.6.00 Form Rev P 10 May 2017
Thermowell Calculation Report
This report is only valid with respect to thermowells produced and supplied by Emerson Automation Solutions in accordance with our exacting quality standards.
Customer Data
Company Name: PT Control Systems Arena Para Nusa Project Name: Pekerjaan EPC
Requestor Name: Insan Gaufuan Customer Drawing:
Analyst: Nesmar Noble Thermowell Model Code:
Reviewer: Customer Purchase Order:
Emerson Sales Order: Emerson Sales Order Line: Preliminary Report
Other Information / Notes: Max tip thickness = 7.9mm; Complete Project Name: Pekerjaan EPC Proyek Pembangunan Terminal LPG Refrigerated Tj Sekong
Process Data
Tag Name: TT-2023 Case 2 Dynamic Fluid Viscosity (μ): 0.1978 [cP]
Process Fluid Velocity (V): 2.84 [m/s] Pressure (P): 18.8 [Kg/cm2-g] (19.83 [Kg/cm2-a])
Thermowell Dimensions
Mounting Configuration: RF-Flanged-Partial Penetration Weld
Process Connection: 2" Class 300
Stem Material: ASTM A 479 GR 316/316L
Stem Style: Tapered Shank
Root Diameter (A): 26.5 [mm]
Tip Diameter (B): 18 [mm]
Bore Diameter (d): 6.6 [mm]
Fillet Radius at Root (b): 4 [mm]
Fillet Radius at Base of Step (bs): Not Applicable
Unsupported Length (L): 260 [mm]
Reduced Diameter Length (Ls): Not Applicable
Minimum Tip Thickness (t): 6.4 [mm] (Not representative of tip allowance)
Protruding Length (PL): 51.98 [mm] (51% of Pipe ID) Representation of Thermowell Dimensions
Von Mises Stress Limit: 2.02e+08 [Pa] Steady State Stress at V (Smax): 2.49e+06 [Pa]
Material Density (ρm): 8030 [kg/m3] Cyclic Stress at VIR (So, max): Not Applicable
Dynamic Stress at V (So, max): Not Applicable (Reduced Diameter)
Frequency
Scruton Number (Nsc): 0.06 Max Allowable Stem Pressure (Pc): 5.35e+07 [Pa]
Frequency Limit: 0.4 Max Allowable Tip Pressure (Pt): 9.72e+08 [Pa]
In-situ Natural Freq (fnc): 302.3 [Hz]
Strouhal Frequency (fs): 30.1 [Hz]
Frequency Ratio (fs/fnc): 0.10
Thermowell Calculation Tool, Software Version: TCTP2_R_2.6.00 Form Rev P 10 May 2017
Thermowell Calculation Report
This report is only valid with respect to thermowells produced and supplied by Emerson Automation Solutions in accordance with our exacting quality standards.
Customer Data
Company Name: PT Control Systems Arena Para Nusa Project Name: Pekerjaan EPC
Requestor Name: Insan Gaufuan Customer Drawing:
Analyst: Nesmar Noble Thermowell Model Code: 114CM0400PAC2SC060AQ5Q8R21XW
Reviewer: Customer Purchase Order:
Emerson Sales Order: Emerson Sales Order Line: Preliminary Report
Other Information / Notes: Max tip thickness = 7.9mm; Complete Project Name: Pekerjaan EPC Proyek Pembangunan Terminal LPG Refrigerated Tj Sekong
Process Data
Tag Name: TT-2030A Dynamic Fluid Viscosity (μ): 0.1959 [cP]
Process Fluid Velocity (V): 0.94 [m/s] Pressure (P): 0.09 [Kg/cm2-g] (1.12 [Kg/cm2-a])
Thermowell Dimensions
Mounting Configuration: RF-Flanged-Partial Penetration Weld
Process Connection: 2" Class 150
Stem Material: ASTM A 479 GR 316/316L
Stem Style: Tapered Shank
Root Diameter (A): 26.5 [mm]
Tip Diameter (B): 18 [mm]
Bore Diameter (d): 6.6 [mm]
Fillet Radius at Root (b): 4 [mm]
Fillet Radius at Base of Step (bs): Not Applicable
Unsupported Length (L): 400 [mm]
Reduced Diameter Length (Ls): Not Applicable
Minimum Tip Thickness (t): 6.4 [mm] (Not representative of tip allowance)
Protruding Length (PL): 188.47 [mm] (49% of Pipe ID) Representation of Thermowell Dimensions
Von Mises Stress Limit: 2.07e+08 [Pa] Steady State Stress at V (Smax): 3.43e+05 [Pa]
Material Density (ρm): 8030 [kg/m3] Cyclic Stress at VIR (So, max): Not Applicable
Dynamic Stress at V (So, max): Not Applicable (Reduced Diameter)
Frequency
Scruton Number (Nsc): 0.06 Max Allowable Stem Pressure (Pc): 5.49e+07 [Pa]
Frequency Limit: 0.4 Max Allowable Tip Pressure (Pt): 9.98e+08 [Pa]
In-situ Natural Freq (fnc): 131.2 [Hz]
Strouhal Frequency (fs): 9.8 [Hz]
Frequency Ratio (fs/fnc): 0.08
Thermowell Calculation Tool, Software Version: TCTP2_R_2.6.00 Form Rev P 10 May 2017
Thermowell Calculation Report
This report is only valid with respect to thermowells produced and supplied by Emerson Automation Solutions in accordance with our exacting quality standards.
Customer Data
Company Name: PT Control Systems Arena Para Nusa Project Name: Pekerjaan EPC
Requestor Name: Insan Gaufuan Customer Drawing:
Analyst: Nesmar Noble Thermowell Model Code: 114CM0400PAC2SC060AQ5Q8R21XW
Reviewer: Customer Purchase Order:
Emerson Sales Order: Emerson Sales Order Line: Preliminary Report
Other Information / Notes: Max tip thickness = 7.9mm; Complete Project Name: Pekerjaan EPC Proyek Pembangunan Terminal LPG Refrigerated Tj Sekong
Process Data
Tag Name: TT-2030B Dynamic Fluid Viscosity (μ): 0.1959 [cP]
Process Fluid Velocity (V): 0.94 [m/s] Pressure (P): 0.09 [Kg/cm2-g] (1.12 [Kg/cm2-a])
Thermowell Dimensions
Mounting Configuration: RF-Flanged-Partial Penetration Weld
Process Connection: 2" Class 150
Stem Material: ASTM A 479 GR 316/316L
Stem Style: Tapered Shank
Root Diameter (A): 26.5 [mm]
Tip Diameter (B): 18 [mm]
Bore Diameter (d): 6.6 [mm]
Fillet Radius at Root (b): 4 [mm]
Fillet Radius at Base of Step (bs): Not Applicable
Unsupported Length (L): 400 [mm]
Reduced Diameter Length (Ls): Not Applicable
Minimum Tip Thickness (t): 6.4 [mm] (Not representative of tip allowance)
Protruding Length (PL): 188.47 [mm] (49% of Pipe ID) Representation of Thermowell Dimensions
Von Mises Stress Limit: 2.07e+08 [Pa] Steady State Stress at V (Smax): 3.43e+05 [Pa]
Material Density (ρm): 8030 [kg/m3] Cyclic Stress at VIR (So, max): Not Applicable
Dynamic Stress at V (So, max): Not Applicable (Reduced Diameter)
Frequency
Scruton Number (Nsc): 0.06 Max Allowable Stem Pressure (Pc): 5.49e+07 [Pa]
Frequency Limit: 0.4 Max Allowable Tip Pressure (Pt): 9.98e+08 [Pa]
In-situ Natural Freq (fnc): 131.2 [Hz]
Strouhal Frequency (fs): 9.8 [Hz]
Frequency Ratio (fs/fnc): 0.08
Thermowell Calculation Tool, Software Version: TCTP2_R_2.6.00 Form Rev P 10 May 2017
Thermowell Calculation Report
This report is only valid with respect to thermowells produced and supplied by Emerson Automation Solutions in accordance with our exacting quality standards.
Customer Data
Company Name: PT Control Systems Arena Para Nusa Project Name: Pekerjaan EPC
Requestor Name: Insan Gaufuan Customer Drawing:
Analyst: Nesmar Noble Thermowell Model Code: 114CM0400PAC2SC060AQ5Q8R21XW
Reviewer: Customer Purchase Order:
Emerson Sales Order: Emerson Sales Order Line: Preliminary Report
Other Information / Notes: Max tip thickness = 7.9mm; Complete Project Name: Pekerjaan EPC Proyek Pembangunan Terminal LPG Refrigerated Tj Sekong
Process Data
Tag Name: TT-2031A Dynamic Fluid Viscosity (μ): 0.1976 [cP]
Process Fluid Velocity (V): 1.87 [m/s] Pressure (P): 0.09 [Kg/cm2-g] (1.12 [Kg/cm2-a])
Thermowell Dimensions
Mounting Configuration: RF-Flanged-Partial Penetration Weld
Process Connection: 2" Class 150
Stem Material: ASTM A 479 GR 316/316L
Stem Style: Tapered Shank
Root Diameter (A): 26.5 [mm]
Tip Diameter (B): 18 [mm]
Bore Diameter (d): 6.6 [mm]
Fillet Radius at Root (b): 4 [mm]
Fillet Radius at Base of Step (bs): Not Applicable
Unsupported Length (L): 400 [mm]
Reduced Diameter Length (Ls): Not Applicable
Minimum Tip Thickness (t): 6.4 [mm] (Not representative of tip allowance)
Protruding Length (PL): 188.47 [mm] (49% of Pipe ID) Representation of Thermowell Dimensions
Von Mises Stress Limit: 2.07e+08 [Pa] Steady State Stress at V (Smax): 1.01e+06 [Pa]
Material Density (ρm): 8030 [kg/m3] Cyclic Stress at VIR (So, max): Not Applicable
Dynamic Stress at V (So, max): Not Applicable (Reduced Diameter)
Frequency
Scruton Number (Nsc): 0.06 Max Allowable Stem Pressure (Pc): 5.49e+07 [Pa]
Frequency Limit: 0.4 Max Allowable Tip Pressure (Pt): 9.98e+08 [Pa]
In-situ Natural Freq (fnc): 131.2 [Hz]
Strouhal Frequency (fs): 19.6 [Hz]
Frequency Ratio (fs/fnc): 0.15
Thermowell Calculation Tool, Software Version: TCTP2_R_2.6.00 Form Rev P 10 May 2017
Thermowell Calculation Report
This report is only valid with respect to thermowells produced and supplied by Emerson Automation Solutions in accordance with our exacting quality standards.
Customer Data
Company Name: PT Control Systems Arena Para Nusa Project Name: Pekerjaan EPC
Requestor Name: Insan Gaufuan Customer Drawing:
Analyst: Nesmar Noble Thermowell Model Code: 114CM0400PAC2SC060AQ5Q8R21XW
Reviewer: Customer Purchase Order:
Emerson Sales Order: Emerson Sales Order Line: Preliminary Report
Other Information / Notes: Max tip thickness = 7.9mm; Complete Project Name: Pekerjaan EPC Proyek Pembangunan Terminal LPG Refrigerated Tj Sekong
Process Data
Tag Name: TT-2031B Dynamic Fluid Viscosity (μ): 0.1976 [cP]
Process Fluid Velocity (V): 1.87 [m/s] Pressure (P): 0.09 [Kg/cm2-g] (1.12 [Kg/cm2-a])
Thermowell Dimensions
Mounting Configuration: RF-Flanged-Partial Penetration Weld
Process Connection: 2" Class 150
Stem Material: ASTM A 479 GR 316/316L
Stem Style: Tapered Shank
Root Diameter (A): 26.5 [mm]
Tip Diameter (B): 18 [mm]
Bore Diameter (d): 6.6 [mm]
Fillet Radius at Root (b): 4 [mm]
Fillet Radius at Base of Step (bs): Not Applicable
Unsupported Length (L): 400 [mm]
Reduced Diameter Length (Ls): Not Applicable
Minimum Tip Thickness (t): 6.4 [mm] (Not representative of tip allowance)
Protruding Length (PL): 188.47 [mm] (49% of Pipe ID) Representation of Thermowell Dimensions
Von Mises Stress Limit: 2.07e+08 [Pa] Steady State Stress at V (Smax): 1.01e+06 [Pa]
Material Density (ρm): 8030 [kg/m3] Cyclic Stress at VIR (So, max): Not Applicable
Dynamic Stress at V (So, max): Not Applicable (Reduced Diameter)
Frequency
Scruton Number (Nsc): 0.06 Max Allowable Stem Pressure (Pc): 5.49e+07 [Pa]
Frequency Limit: 0.4 Max Allowable Tip Pressure (Pt): 9.98e+08 [Pa]
In-situ Natural Freq (fnc): 131.2 [Hz]
Strouhal Frequency (fs): 19.6 [Hz]
Frequency Ratio (fs/fnc): 0.15
Thermowell Calculation Tool, Software Version: TCTP2_R_2.6.00 Form Rev P 10 May 2017
Thermowell Calculation Report
This report is only valid with respect to thermowells produced and supplied by Emerson Automation Solutions in accordance with our exacting quality standards.
Customer Data
Company Name: PT Control Systems Arena Para Nusa Project Name: Pekerjaan EPC
Requestor Name: Insan Gaufuan Customer Drawing:
Analyst: Nesmar Noble Thermowell Model Code: 114CM0400PAC2SC060AQ5Q8R21XW
Reviewer: Customer Purchase Order:
Emerson Sales Order: Emerson Sales Order Line: Preliminary Report
Other Information / Notes: Max tip thickness = 7.9mm; Complete Project Name: Pekerjaan EPC Proyek Pembangunan Terminal LPG Refrigerated Tj Sekong
Process Data
Tag Name: TT-2031C Dynamic Fluid Viscosity (μ): 0.1976 [cP]
Process Fluid Velocity (V): 1.87 [m/s] Pressure (P): 0.09 [Kg/cm2-g] (1.12 [Kg/cm2-a])
Thermowell Dimensions
Mounting Configuration: RF-Flanged-Partial Penetration Weld
Process Connection: 2" Class 150
Stem Material: ASTM A 479 GR 316/316L
Stem Style: Tapered Shank
Root Diameter (A): 26.5 [mm]
Tip Diameter (B): 18 [mm]
Bore Diameter (d): 6.6 [mm]
Fillet Radius at Root (b): 4 [mm]
Fillet Radius at Base of Step (bs): Not Applicable
Unsupported Length (L): 400 [mm]
Reduced Diameter Length (Ls): Not Applicable
Minimum Tip Thickness (t): 6.4 [mm] (Not representative of tip allowance)
Protruding Length (PL): 188.47 [mm] (49% of Pipe ID) Representation of Thermowell Dimensions
Von Mises Stress Limit: 2.07e+08 [Pa] Steady State Stress at V (Smax): 1.01e+06 [Pa]
Material Density (ρm): 8030 [kg/m3] Cyclic Stress at VIR (So, max): Not Applicable
Dynamic Stress at V (So, max): Not Applicable (Reduced Diameter)
Frequency
Scruton Number (Nsc): 0.06 Max Allowable Stem Pressure (Pc): 5.49e+07 [Pa]
Frequency Limit: 0.4 Max Allowable Tip Pressure (Pt): 9.98e+08 [Pa]
In-situ Natural Freq (fnc): 131.2 [Hz]
Strouhal Frequency (fs): 19.6 [Hz]
Frequency Ratio (fs/fnc): 0.15
Thermowell Calculation Tool, Software Version: TCTP2_R_2.6.00 Form Rev P 10 May 2017
Thermowell Calculation Report
This report is only valid with respect to thermowells produced and supplied by Emerson Automation Solutions in accordance with our exacting quality standards.
Customer Data
Company Name: PT Control Systems Arena Para Nusa Project Name: Pekerjaan EPC
Requestor Name: Insan Gaufuan Customer Drawing:
Analyst: Nesmar Noble Thermowell Model Code: 114CM0370PAC2SC060AQ5Q8R21XW
Reviewer: Customer Purchase Order:
Emerson Sales Order: Emerson Sales Order Line: Preliminary Report
Other Information / Notes: Max tip thickness = 7.9mm; Complete Project Name: Pekerjaan EPC Proyek Pembangunan Terminal LPG Refrigerated Tj Sekong
Process Data
Tag Name: TT-2032A Dynamic Fluid Viscosity (μ): 0.1976 [cP]
Process Fluid Velocity (V): 2.48 [m/s] Pressure (P): 0.09 [Kg/cm2-g] (1.12 [Kg/cm2-a])
Thermowell Dimensions
Mounting Configuration: RF-Flanged-Partial Penetration Weld
Process Connection: 2" Class 150
Stem Material: ASTM A 479 GR 316/316L
Stem Style: Tapered Shank
Root Diameter (A): 26.5 [mm]
Tip Diameter (B): 18 [mm]
Bore Diameter (d): 6.6 [mm]
Fillet Radius at Root (b): 4 [mm]
Fillet Radius at Base of Step (bs): Not Applicable
Unsupported Length (L): 370 [mm]
Reduced Diameter Length (Ls): Not Applicable
Minimum Tip Thickness (t): 6.4 [mm] (Not representative of tip allowance)
Protruding Length (PL): 158.47 [mm] (47% of Pipe ID) Representation of Thermowell Dimensions
Von Mises Stress Limit: 2.07e+08 [Pa] Steady State Stress at V (Smax): 1.36e+06 [Pa]
Material Density (ρm): 8030 [kg/m3] Cyclic Stress at VIR (So, max): Not Applicable
Dynamic Stress at V (So, max): Not Applicable (Reduced Diameter)
Frequency
Scruton Number (Nsc): 0.06 Max Allowable Stem Pressure (Pc): 5.49e+07 [Pa]
Frequency Limit: 0.4 Max Allowable Tip Pressure (Pt): 9.98e+08 [Pa]
In-situ Natural Freq (fnc): 152.8 [Hz]
Strouhal Frequency (fs): 26.2 [Hz]
Frequency Ratio (fs/fnc): 0.17
Thermowell Calculation Tool, Software Version: TCTP2_R_2.6.00 Form Rev P 10 May 2017
Thermowell Calculation Report
This report is only valid with respect to thermowells produced and supplied by Emerson Automation Solutions in accordance with our exacting quality standards.
Customer Data
Company Name: PT Control Systems Arena Para Nusa Project Name: Pekerjaan EPC
Requestor Name: Insan Gaufuan Customer Drawing:
Analyst: Nesmar Noble Thermowell Model Code: 114CM0370PAC2SC060AQ5Q8R21XW
Reviewer: Customer Purchase Order:
Emerson Sales Order: Emerson Sales Order Line: Preliminary Report
Other Information / Notes: Max tip thickness = 7.9mm; Complete Project Name: Pekerjaan EPC Proyek Pembangunan Terminal LPG Refrigerated Tj Sekong
Process Data
Tag Name: TT-2032B Dynamic Fluid Viscosity (μ): 0.1976 [cP]
Process Fluid Velocity (V): 2.48 [m/s] Pressure (P): 0.09 [Kg/cm2-g] (1.12 [Kg/cm2-a])
Thermowell Dimensions
Mounting Configuration: RF-Flanged-Partial Penetration Weld
Process Connection: 2" Class 150
Stem Material: ASTM A 479 GR 316/316L
Stem Style: Tapered Shank
Root Diameter (A): 26.5 [mm]
Tip Diameter (B): 18 [mm]
Bore Diameter (d): 6.6 [mm]
Fillet Radius at Root (b): 4 [mm]
Fillet Radius at Base of Step (bs): Not Applicable
Unsupported Length (L): 370 [mm]
Reduced Diameter Length (Ls): Not Applicable
Minimum Tip Thickness (t): 6.4 [mm] (Not representative of tip allowance)
Protruding Length (PL): 158.47 [mm] (47% of Pipe ID) Representation of Thermowell Dimensions
Von Mises Stress Limit: 2.07e+08 [Pa] Steady State Stress at V (Smax): 1.36e+06 [Pa]
Material Density (ρm): 8030 [kg/m3] Cyclic Stress at VIR (So, max): Not Applicable
Dynamic Stress at V (So, max): Not Applicable (Reduced Diameter)
Frequency
Scruton Number (Nsc): 0.06 Max Allowable Stem Pressure (Pc): 5.49e+07 [Pa]
Frequency Limit: 0.4 Max Allowable Tip Pressure (Pt): 9.98e+08 [Pa]
In-situ Natural Freq (fnc): 152.8 [Hz]
Strouhal Frequency (fs): 26.2 [Hz]
Frequency Ratio (fs/fnc): 0.17
Thermowell Calculation Tool, Software Version: TCTP2_R_2.6.00 Form Rev P 10 May 2017
Thermowell Calculation Report
This report is only valid with respect to thermowells produced and supplied by Emerson Automation Solutions in accordance with our exacting quality standards.
Customer Data
Company Name: PT Control Systems Arena Para Nusa Project Name: Pekerjaan EPC
Requestor Name: Insan Gaufuan Customer Drawing:
Analyst: Nesmar Noble Thermowell Model Code: 114CM0300PAC2SC060AQ5Q8R21XW
Reviewer: Customer Purchase Order:
Emerson Sales Order: Emerson Sales Order Line: Preliminary Report
Other Information / Notes: Max tip thickness = 7.9mm; Complete Project Name: Pekerjaan EPC Proyek Pembangunan Terminal LPG Refrigerated Tj Sekong
Process Data
Tag Name: TT-2053 Dynamic Fluid Viscosity (μ): 0.0068 [cP]
Process Fluid Velocity (V): 4.27 [m/s] Pressure (P): 0.44 [Kg/cm2-g] (1.47 [Kg/cm2-a])
Thermowell Dimensions
Mounting Configuration: RF-Flanged-Partial Penetration Weld
Process Connection: 2" Class 150
Stem Material: ASTM A 479 GR 316/316L
Stem Style: Tapered Shank
Root Diameter (A): 26.5 [mm]
Tip Diameter (B): 18 [mm]
Bore Diameter (d): 6.6 [mm]
Fillet Radius at Root (b): 4 [mm]
Fillet Radius at Base of Step (bs): Not Applicable
Unsupported Length (L): 300 [mm]
Reduced Diameter Length (Ls): Not Applicable
Minimum Tip Thickness (t): 6.4 [mm] (Not representative of tip allowance)
Protruding Length (PL): 88.23 [mm] (35% of Pipe ID) Representation of Thermowell Dimensions
Von Mises Stress Limit: 2.02e+08 [Pa] Steady State Stress at V (Smax): 1.62e+05 [Pa]
Material Density (ρm): 8030 [kg/m3] Cyclic Stress at VIR (So, max): Not Applicable
Dynamic Stress at V (So, max): Not Applicable (Reduced Diameter)
Frequency
Scruton Number (Nsc): 12.75 Max Allowable Stem Pressure (Pc): 5.35e+07 [Pa]
Frequency Limit: 0.8 Max Allowable Tip Pressure (Pt): 9.72e+08 [Pa]
In-situ Natural Freq (fnc): 237.1 [Hz]
Strouhal Frequency (fs): 45.3 [Hz]
Frequency Ratio (fs/fnc): 0.19
Thermowell Calculation Tool, Software Version: TCTP2_R_2.6.00 Form Rev P 10 May 2017
Thermowell Calculation Report
This report is only valid with respect to thermowells produced and supplied by Emerson Automation Solutions in accordance with our exacting quality standards.
Customer Data
Company Name: PT Control Systems Arena Para Nusa Project Name: Pekerjaan EPC
Requestor Name: Insan Gaufuan Customer Drawing:
Analyst: Nesmar Noble Thermowell Model Code: 114CM0400PAC2SC060AQ5Q8R21XW
Reviewer: Customer Purchase Order:
Emerson Sales Order: Emerson Sales Order Line: Preliminary Report
Other Information / Notes: Max tip thickness = 7.9mm; Complete Project Name: Pekerjaan EPC Proyek Pembangunan Terminal LPG Refrigerated Tj Sekong
Process Data
Tag Name: TT-2054 Dynamic Fluid Viscosity (μ): 0.0068 [cP]
Process Fluid Velocity (V): 10.57 [m/s] Pressure (P): 0.09 [Kg/cm2-g] (1.12 [Kg/cm2-a])
Thermowell Dimensions
Mounting Configuration: RF-Flanged-Partial Penetration Weld
Process Connection: 2" Class 150
Stem Material: ASTM A 479 GR 316/316L
Stem Style: Tapered Shank
Root Diameter (A): 26.5 [mm]
Tip Diameter (B): 18 [mm]
Bore Diameter (d): 6.6 [mm]
Fillet Radius at Root (b): 4 [mm]
Fillet Radius at Base of Step (bs): Not Applicable
Unsupported Length (L): 390 [mm]
Reduced Diameter Length (Ls): Not Applicable
Minimum Tip Thickness (t): 6.4 [mm] (Not representative of tip allowance)
Protruding Length (PL): 178.47 [mm] (46% of Pipe ID) Representation of Thermowell Dimensions
Von Mises Stress Limit: 2.02e+08 [Pa] Steady State Stress at V (Smax): 2.40e+05 [Pa]
Material Density (ρm): 8030 [kg/m3] Cyclic Stress at VIR (So, max): Not Applicable
Dynamic Stress at V (So, max): Not Applicable (Reduced Diameter)
Frequency
Scruton Number (Nsc): 12.75 Max Allowable Stem Pressure (Pc): 5.35e+07 [Pa]
Frequency Limit: 0.8 Max Allowable Tip Pressure (Pt): 9.72e+08 [Pa]
In-situ Natural Freq (fnc): 141.7 [Hz]
Strouhal Frequency (fs): 110.4 [Hz]
Frequency Ratio (fs/fnc): 0.78
Thermowell Calculation Tool, Software Version: TCTP2_R_2.6.00 Form Rev P 10 May 2017
Thermowell Calculation Report
This report is only valid with respect to thermowells produced and supplied by Emerson Automation Solutions in accordance with our exacting quality standards.
Customer Data
Company Name: PT Control Systems Arena Para Nusa Project Name: Pekerjaan EPC
Requestor Name: Insan Gaufuan Customer Drawing:
Analyst: Nesmar Noble Thermowell Model Code: 114CM0230PAC2SC060AQ5Q8R21XW
Reviewer: Customer Purchase Order:
Emerson Sales Order: Emerson Sales Order Line: Preliminary Report
Other Information / Notes: Max tip thickness = 7.9mm; Complete Project Name: Pekerjaan EPC Proyek Pembangunan Terminal LPG Refrigerated Tj Sekong
Process Data
Tag Name: TT-2058 Dynamic Fluid Viscosity (μ): 0.1513 [cP]
Process Fluid Velocity (V): 0.27 [m/s] Pressure (P): 5.5 [Kg/cm2-g] (6.53 [Kg/cm2-a])
Thermowell Dimensions
Mounting Configuration: RF-Flanged-Partial Penetration Weld
Process Connection: 2" Class 150
Stem Material: ASTM A 479 GR 316/316L
Stem Style: Tapered Shank
Root Diameter (A): 26.5 [mm]
Tip Diameter (B): 18 [mm]
Bore Diameter (d): 6.6 [mm]
Fillet Radius at Root (b): 4 [mm]
Fillet Radius at Base of Step (bs): Not Applicable
Unsupported Length (L): 230 [mm]
Reduced Diameter Length (Ls): Not Applicable
Minimum Tip Thickness (t): 6.4 [mm] (Not representative of tip allowance)
Protruding Length (PL): 14.89 [mm] (10% of Pipe ID) Representation of Thermowell Dimensions
Von Mises Stress Limit: 1.97e+08 [Pa] Steady State Stress at V (Smax): 6.84e+05 [Pa]
Material Density (ρm): 8030 [kg/m3] Cyclic Stress at VIR (So, max): Not Applicable
Dynamic Stress at V (So, max): Not Applicable (Reduced Diameter)
Frequency
Scruton Number (Nsc): 0.06 Max Allowable Stem Pressure (Pc): 5.22e+07 [Pa]
Frequency Limit: 0.4 Max Allowable Tip Pressure (Pt): 9.50e+08 [Pa]
In-situ Natural Freq (fnc): 382.3 [Hz]
Strouhal Frequency (fs): 2.9 [Hz]
Frequency Ratio (fs/fnc): 0.01
Thermowell Calculation Tool, Software Version: TCTP2_R_2.6.00 Form Rev P 10 May 2017
Thermowell Calculation Report
This report is only valid with respect to thermowells produced and supplied by Emerson Automation Solutions in accordance with our exacting quality standards.
Customer Data
Company Name: PT Control Systems Arena Para Nusa Project Name: Pekerjaan EPC
Requestor Name: Insan Gaufuan Customer Drawing:
Analyst: Nesmar Noble Thermowell Model Code:
Reviewer: Customer Purchase Order:
Emerson Sales Order: Emerson Sales Order Line: Preliminary Report
Other Information / Notes: Max tip thickness = 7.9mm; Complete Project Name: Pekerjaan EPC Proyek Pembangunan Terminal LPG Refrigerated Tj Sekong
Process Data
Tag Name: TT-2071 Dynamic Fluid Viscosity (μ): 0.1218 [cP]
Process Fluid Velocity (V): 2.6 [m/s] Pressure (P): 18.51 [Kg/cm2-g] (19.54 [Kg/cm2-a])
Thermowell Dimensions
Mounting Configuration: RF-Flanged-Partial Penetration Weld
Process Connection: 2" Class 300
Stem Material: ASTM A 479 GR 316/316L
Stem Style: Tapered Shank
Root Diameter (A): 26.5 [mm]
Tip Diameter (B): 18 [mm]
Bore Diameter (d): 6.6 [mm]
Fillet Radius at Root (b): 4 [mm]
Fillet Radius at Base of Step (bs): Not Applicable
Unsupported Length (L): 265 [mm]
Reduced Diameter Length (Ls): Not Applicable
Minimum Tip Thickness (t): 6.4 [mm] (Not representative of tip allowance)
Protruding Length (PL): 56.98 [mm] (56% of Pipe ID) Representation of Thermowell Dimensions
Von Mises Stress Limit: 2.02e+08 [Pa] Steady State Stress at V (Smax): 2.44e+06 [Pa]
Material Density (ρm): 8030 [kg/m3] Cyclic Stress at VIR (So, max): Not Applicable
Dynamic Stress at V (So, max): Not Applicable (Reduced Diameter)
Frequency
Scruton Number (Nsc): 0.06 Max Allowable Stem Pressure (Pc): 5.35e+07 [Pa]
Frequency Limit: 0.4 Max Allowable Tip Pressure (Pt): 9.72e+08 [Pa]
In-situ Natural Freq (fnc): 291.0 [Hz]
Strouhal Frequency (fs): 28.3 [Hz]
Frequency Ratio (fs/fnc): 0.10
Thermowell Calculation Tool, Software Version: TCTP2_R_2.6.00 Form Rev P 10 May 2017
Thermowell Calculation Report
This report is only valid with respect to thermowells produced and supplied by Emerson Automation Solutions in accordance with our exacting quality standards.
Customer Data
Company Name: PT Control Systems Arena Para Nusa Project Name: Pekerjaan EPC
Requestor Name: Insan Gaufuan Customer Drawing:
Analyst: Nesmar Noble Thermowell Model Code: 114CM0400PAC2SC060AQ5Q8R21XW
Reviewer: Customer Purchase Order:
Emerson Sales Order: Emerson Sales Order Line: Preliminary Report
Other Information / Notes: Max tip thickness = 7.9mm; Complete Project Name: Pekerjaan EPC Proyek Pembangunan Terminal LPG Refrigerated Tj Sekong
Process Data
Tag Name: TT-2080A Dynamic Fluid Viscosity (μ): 0.2101 [cP]
Process Fluid Velocity (V): 0.9 [m/s] Pressure (P): 0.09 [Kg/cm2-g] (1.12 [Kg/cm2-a])
Thermowell Dimensions
Mounting Configuration: RF-Flanged-Partial Penetration Weld
Process Connection: 2" Class 150
Stem Material: ASTM A 479 GR 316/316L
Stem Style: Tapered Shank
Root Diameter (A): 26.5 [mm]
Tip Diameter (B): 18 [mm]
Bore Diameter (d): 6.6 [mm]
Fillet Radius at Root (b): 4 [mm]
Fillet Radius at Base of Step (bs): Not Applicable
Unsupported Length (L): 400 [mm]
Reduced Diameter Length (Ls): Not Applicable
Minimum Tip Thickness (t): 6.4 [mm] (Not representative of tip allowance)
Protruding Length (PL): 188.47 [mm] (49% of Pipe ID) Representation of Thermowell Dimensions
Von Mises Stress Limit: 2.03e+08 [Pa] Steady State Stress at V (Smax): 3.31e+05 [Pa]
Material Density (ρm): 8030 [kg/m3] Cyclic Stress at VIR (So, max): Not Applicable
Dynamic Stress at V (So, max): Not Applicable (Reduced Diameter)
Frequency
Scruton Number (Nsc): 0.06 Max Allowable Stem Pressure (Pc): 5.38e+07 [Pa]
Frequency Limit: 0.4 Max Allowable Tip Pressure (Pt): 9.78e+08 [Pa]
In-situ Natural Freq (fnc): 130.1 [Hz]
Strouhal Frequency (fs): 9.4 [Hz]
Frequency Ratio (fs/fnc): 0.07
Thermowell Calculation Tool, Software Version: TCTP2_R_2.6.00 Form Rev P 10 May 2017
Thermowell Calculation Report
This report is only valid with respect to thermowells produced and supplied by Emerson Automation Solutions in accordance with our exacting quality standards.
Customer Data
Company Name: PT Control Systems Arena Para Nusa Project Name: Pekerjaan EPC
Requestor Name: Insan Gaufuan Customer Drawing:
Analyst: Nesmar Noble Thermowell Model Code: 114CM0400PAC2SC060AQ5Q8R21XW
Reviewer: Customer Purchase Order:
Emerson Sales Order: Emerson Sales Order Line: Preliminary Report
Other Information / Notes: Max tip thickness = 7.9mm; Complete Project Name: Pekerjaan EPC Proyek Pembangunan Terminal LPG Refrigerated Tj Sekong
Process Data
Tag Name: TT-2080B Dynamic Fluid Viscosity (μ): 0.2101 [cP]
Process Fluid Velocity (V): 0.9 [m/s] Pressure (P): 0.09 [Kg/cm2-g] (1.12 [Kg/cm2-a])
Thermowell Dimensions
Mounting Configuration: RF-Flanged-Partial Penetration Weld
Process Connection: 2" Class 150
Stem Material: ASTM A 479 GR 316/316L
Stem Style: Tapered Shank
Root Diameter (A): 26.5 [mm]
Tip Diameter (B): 18 [mm]
Bore Diameter (d): 6.6 [mm]
Fillet Radius at Root (b): 4 [mm]
Fillet Radius at Base of Step (bs): Not Applicable
Unsupported Length (L): 400 [mm]
Reduced Diameter Length (Ls): Not Applicable
Minimum Tip Thickness (t): 6.4 [mm] (Not representative of tip allowance)
Protruding Length (PL): 188.47 [mm] (49% of Pipe ID) Representation of Thermowell Dimensions
Von Mises Stress Limit: 2.03e+08 [Pa] Steady State Stress at V (Smax): 3.31e+05 [Pa]
Material Density (ρm): 8030 [kg/m3] Cyclic Stress at VIR (So, max): Not Applicable
Dynamic Stress at V (So, max): Not Applicable (Reduced Diameter)
Frequency
Scruton Number (Nsc): 0.06 Max Allowable Stem Pressure (Pc): 5.38e+07 [Pa]
Frequency Limit: 0.4 Max Allowable Tip Pressure (Pt): 9.78e+08 [Pa]
In-situ Natural Freq (fnc): 130.1 [Hz]
Strouhal Frequency (fs): 9.4 [Hz]
Frequency Ratio (fs/fnc): 0.07
Thermowell Calculation Tool, Software Version: TCTP2_R_2.6.00 Form Rev P 10 May 2017
Thermowell Calculation Report
This report is only valid with respect to thermowells produced and supplied by Emerson Automation Solutions in accordance with our exacting quality standards.
Customer Data
Company Name: PT Control Systems Arena Para Nusa Project Name: Pekerjaan EPC
Requestor Name: Insan Gaufuan Customer Drawing:
Analyst: Nesmar Noble Thermowell Model Code: 114CM0400PAC2SC060AQ5Q8R21XW
Reviewer: Customer Purchase Order:
Emerson Sales Order: Emerson Sales Order Line: Preliminary Report
Other Information / Notes: Max tip thickness = 7.9mm; Complete Project Name: Pekerjaan EPC Proyek Pembangunan Terminal LPG Refrigerated Tj Sekong
Process Data
Tag Name: TT-2081A Dynamic Fluid Viscosity (μ): 0.2121 [cP]
Process Fluid Velocity (V): 1.81 [m/s] Pressure (P): 0.09 [Kg/cm2-g] (1.12 [Kg/cm2-a])
Thermowell Dimensions
Mounting Configuration: RF-Flanged-Partial Penetration Weld
Process Connection: 2" Class 150
Stem Material: ASTM A 479 GR 316/316L
Stem Style: Tapered Shank
Root Diameter (A): 26.5 [mm]
Tip Diameter (B): 18 [mm]
Bore Diameter (d): 6.6 [mm]
Fillet Radius at Root (b): 4 [mm]
Fillet Radius at Base of Step (bs): Not Applicable
Unsupported Length (L): 400 [mm]
Reduced Diameter Length (Ls): Not Applicable
Minimum Tip Thickness (t): 6.4 [mm] (Not representative of tip allowance)
Protruding Length (PL): 188.47 [mm] (49% of Pipe ID) Representation of Thermowell Dimensions
Von Mises Stress Limit: 2.03e+08 [Pa] Steady State Stress at V (Smax): 9.82e+05 [Pa]
Material Density (ρm): 8030 [kg/m3] Cyclic Stress at VIR (So, max): Not Applicable
Dynamic Stress at V (So, max): Not Applicable (Reduced Diameter)
Frequency
Scruton Number (Nsc): 0.06 Max Allowable Stem Pressure (Pc): 5.38e+07 [Pa]
Frequency Limit: 0.4 Max Allowable Tip Pressure (Pt): 9.78e+08 [Pa]
In-situ Natural Freq (fnc): 130.1 [Hz]
Strouhal Frequency (fs): 18.9 [Hz]
Frequency Ratio (fs/fnc): 0.15
Thermowell Calculation Tool, Software Version: TCTP2_R_2.6.00 Form Rev P 10 May 2017
Thermowell Calculation Report
This report is only valid with respect to thermowells produced and supplied by Emerson Automation Solutions in accordance with our exacting quality standards.
Customer Data
Company Name: PT Control Systems Arena Para Nusa Project Name: Pekerjaan EPC
Requestor Name: Insan Gaufuan Customer Drawing:
Analyst: Nesmar Noble Thermowell Model Code: 114CM0400PAC2SC060AQ5Q8R21XW
Reviewer: Customer Purchase Order:
Emerson Sales Order: Emerson Sales Order Line: Preliminary Report
Other Information / Notes: Max tip thickness = 7.9mm; Complete Project Name: Pekerjaan EPC Proyek Pembangunan Terminal LPG Refrigerated Tj Sekong
Process Data
Tag Name: TT-2081B Dynamic Fluid Viscosity (μ): 0.2121 [cP]
Process Fluid Velocity (V): 1.81 [m/s] Pressure (P): 0.09 [Kg/cm2-g] (1.12 [Kg/cm2-a])
Thermowell Dimensions
Mounting Configuration: RF-Flanged-Partial Penetration Weld
Process Connection: 2" Class 150
Stem Material: ASTM A 479 GR 316/316L
Stem Style: Tapered Shank
Root Diameter (A): 26.5 [mm]
Tip Diameter (B): 18 [mm]
Bore Diameter (d): 6.6 [mm]
Fillet Radius at Root (b): 4 [mm]
Fillet Radius at Base of Step (bs): Not Applicable
Unsupported Length (L): 400 [mm]
Reduced Diameter Length (Ls): Not Applicable
Minimum Tip Thickness (t): 6.4 [mm] (Not representative of tip allowance)
Protruding Length (PL): 188.47 [mm] (49% of Pipe ID) Representation of Thermowell Dimensions
Von Mises Stress Limit: 2.03e+08 [Pa] Steady State Stress at V (Smax): 9.82e+05 [Pa]
Material Density (ρm): 8030 [kg/m3] Cyclic Stress at VIR (So, max): Not Applicable
Dynamic Stress at V (So, max): Not Applicable (Reduced Diameter)
Frequency
Scruton Number (Nsc): 0.06 Max Allowable Stem Pressure (Pc): 5.38e+07 [Pa]
Frequency Limit: 0.4 Max Allowable Tip Pressure (Pt): 9.78e+08 [Pa]
In-situ Natural Freq (fnc): 130.1 [Hz]
Strouhal Frequency (fs): 18.9 [Hz]
Frequency Ratio (fs/fnc): 0.15
Thermowell Calculation Tool, Software Version: TCTP2_R_2.6.00 Form Rev P 10 May 2017
Thermowell Calculation Report
This report is only valid with respect to thermowells produced and supplied by Emerson Automation Solutions in accordance with our exacting quality standards.
Customer Data
Company Name: PT Control Systems Arena Para Nusa Project Name: Pekerjaan EPC
Requestor Name: Insan Gaufuan Customer Drawing:
Analyst: Nesmar Noble Thermowell Model Code: 114CM0400PAC2SC060AQ5Q8R21XW
Reviewer: Customer Purchase Order:
Emerson Sales Order: Emerson Sales Order Line: Preliminary Report
Other Information / Notes: Max tip thickness = 7.9mm; Complete Project Name: Pekerjaan EPC Proyek Pembangunan Terminal LPG Refrigerated Tj Sekong
Process Data
Tag Name: TT-2081C Dynamic Fluid Viscosity (μ): 0.2121 [cP]
Process Fluid Velocity (V): 1.81 [m/s] Pressure (P): 0.09 [Kg/cm2-g] (1.12 [Kg/cm2-a])
Thermowell Dimensions
Mounting Configuration: RF-Flanged-Partial Penetration Weld
Process Connection: 2" Class 150
Stem Material: ASTM A 479 GR 316/316L
Stem Style: Tapered Shank
Root Diameter (A): 26.5 [mm]
Tip Diameter (B): 18 [mm]
Bore Diameter (d): 6.6 [mm]
Fillet Radius at Root (b): 4 [mm]
Fillet Radius at Base of Step (bs): Not Applicable
Unsupported Length (L): 400 [mm]
Reduced Diameter Length (Ls): Not Applicable
Minimum Tip Thickness (t): 6.4 [mm] (Not representative of tip allowance)
Protruding Length (PL): 188.47 [mm] (49% of Pipe ID) Representation of Thermowell Dimensions
Von Mises Stress Limit: 2.03e+08 [Pa] Steady State Stress at V (Smax): 9.82e+05 [Pa]
Material Density (ρm): 8030 [kg/m3] Cyclic Stress at VIR (So, max): Not Applicable
Dynamic Stress at V (So, max): Not Applicable (Reduced Diameter)
Frequency
Scruton Number (Nsc): 0.06 Max Allowable Stem Pressure (Pc): 5.38e+07 [Pa]
Frequency Limit: 0.4 Max Allowable Tip Pressure (Pt): 9.78e+08 [Pa]
In-situ Natural Freq (fnc): 130.1 [Hz]
Strouhal Frequency (fs): 18.9 [Hz]
Frequency Ratio (fs/fnc): 0.15
Thermowell Calculation Tool, Software Version: TCTP2_R_2.6.00 Form Rev P 10 May 2017
Thermowell Calculation Report
This report is only valid with respect to thermowells produced and supplied by Emerson Automation Solutions in accordance with our exacting quality standards.
Customer Data
Company Name: PT Control Systems Arena Para Nusa Project Name: Pekerjaan EPC
Requestor Name: Insan Gaufuan Customer Drawing:
Analyst: Nesmar Noble Thermowell Model Code: 114CM0370PAC2SC060AQ5Q8R21XW
Reviewer: Customer Purchase Order:
Emerson Sales Order: Emerson Sales Order Line: Preliminary Report
Other Information / Notes: Max tip thickness = 7.9mm; Complete Project Name: Pekerjaan EPC Proyek Pembangunan Terminal LPG Refrigerated Tj Sekong
Process Data
Tag Name: TT-2082A Dynamic Fluid Viscosity (μ): 0.2121 [cP]
Process Fluid Velocity (V): 2.4 [m/s] Pressure (P): 0.09 [Kg/cm2-g] (1.12 [Kg/cm2-a])
Thermowell Dimensions
Mounting Configuration: RF-Flanged-Partial Penetration Weld
Process Connection: 2" Class 150
Stem Material: ASTM A 479 GR 316/316L
Stem Style: Tapered Shank
Root Diameter (A): 26.5 [mm]
Tip Diameter (B): 18 [mm]
Bore Diameter (d): 6.6 [mm]
Fillet Radius at Root (b): 4 [mm]
Fillet Radius at Base of Step (bs): Not Applicable
Unsupported Length (L): 370 [mm]
Reduced Diameter Length (Ls): Not Applicable
Minimum Tip Thickness (t): 6.4 [mm] (Not representative of tip allowance)
Protruding Length (PL): 158.47 [mm] (47% of Pipe ID) Representation of Thermowell Dimensions
Von Mises Stress Limit: 2.03e+08 [Pa] Steady State Stress at V (Smax): 1.32e+06 [Pa]
Material Density (ρm): 8030 [kg/m3] Cyclic Stress at VIR (So, max): Not Applicable
Dynamic Stress at V (So, max): Not Applicable (Reduced Diameter)
Frequency
Scruton Number (Nsc): 0.06 Max Allowable Stem Pressure (Pc): 5.38e+07 [Pa]
Frequency Limit: 0.4 Max Allowable Tip Pressure (Pt): 9.78e+08 [Pa]
In-situ Natural Freq (fnc): 151.6 [Hz]
Strouhal Frequency (fs): 25.3 [Hz]
Frequency Ratio (fs/fnc): 0.17
Thermowell Calculation Tool, Software Version: TCTP2_R_2.6.00 Form Rev P 10 May 2017
Thermowell Calculation Report
This report is only valid with respect to thermowells produced and supplied by Emerson Automation Solutions in accordance with our exacting quality standards.
Customer Data
Company Name: PT Control Systems Arena Para Nusa Project Name: Pekerjaan EPC
Requestor Name: Insan Gaufuan Customer Drawing:
Analyst: Nesmar Noble Thermowell Model Code: 114CM0370PAC2SC060AQ5Q8R21XW
Reviewer: Customer Purchase Order:
Emerson Sales Order: Emerson Sales Order Line: Preliminary Report
Other Information / Notes: Max tip thickness = 7.9mm; Complete Project Name: Pekerjaan EPC Proyek Pembangunan Terminal LPG Refrigerated Tj Sekong
Process Data
Tag Name: TT-2082B Dynamic Fluid Viscosity (μ): 0.2121 [cP]
Process Fluid Velocity (V): 2.4 [m/s] Pressure (P): 0.09 [Kg/cm2-g] (1.12 [Kg/cm2-a])
Thermowell Dimensions
Mounting Configuration: RF-Flanged-Partial Penetration Weld
Process Connection: 2" Class 150
Stem Material: ASTM A 479 GR 316/316L
Stem Style: Tapered Shank
Root Diameter (A): 26.5 [mm]
Tip Diameter (B): 18 [mm]
Bore Diameter (d): 6.6 [mm]
Fillet Radius at Root (b): 4 [mm]
Fillet Radius at Base of Step (bs): Not Applicable
Unsupported Length (L): 370 [mm]
Reduced Diameter Length (Ls): Not Applicable
Minimum Tip Thickness (t): 6.4 [mm] (Not representative of tip allowance)
Protruding Length (PL): 158.47 [mm] (47% of Pipe ID) Representation of Thermowell Dimensions
Von Mises Stress Limit: 2.03e+08 [Pa] Steady State Stress at V (Smax): 1.32e+06 [Pa]
Material Density (ρm): 8030 [kg/m3] Cyclic Stress at VIR (So, max): Not Applicable
Dynamic Stress at V (So, max): Not Applicable (Reduced Diameter)
Frequency
Scruton Number (Nsc): 0.06 Max Allowable Stem Pressure (Pc): 5.38e+07 [Pa]
Frequency Limit: 0.4 Max Allowable Tip Pressure (Pt): 9.78e+08 [Pa]
In-situ Natural Freq (fnc): 151.6 [Hz]
Strouhal Frequency (fs): 25.3 [Hz]
Frequency Ratio (fs/fnc): 0.17
Thermowell Calculation Tool, Software Version: TCTP2_R_2.6.00 Form Rev P 10 May 2017
Thermowell Calculation Report
This report is only valid with respect to thermowells produced and supplied by Emerson Automation Solutions in accordance with our exacting quality standards.
Customer Data
Company Name: PT Control Systems Arena Para Nusa Project Name: Pekerjaan EPC
Requestor Name: Insan Gaufuan Customer Drawing:
Analyst: Nesmar Noble Thermowell Model Code:
Reviewer: Customer Purchase Order:
Emerson Sales Order: Emerson Sales Order Line: Preliminary Report
Other Information / Notes: Max tip thickness = 7.9mm; Complete Project Name: Pekerjaan EPC Proyek Pembangunan Terminal LPG Refrigerated Tj Sekong
Process Data
Tag Name: TT-6007 Dynamic Fluid Viscosity (μ): 0.86 [cP]
Process Fluid Velocity (V): 3.24 [m/s] Pressure (P): 6.8 [Kg/cm2-g] (7.83 [Kg/cm2-a])
Thermowell Dimensions
Mounting Configuration: FF-Flanged-Partial Penetration Weld
Process Connection: 2" Class 150
Stem Material: ASTM B 164 GR 400
Stem Style: Tapered Shank
Root Diameter (A): 26.5 [mm]
Tip Diameter (B): 18 [mm]
Bore Diameter (d): 6.6 [mm]
Fillet Radius at Root (b): 4 [mm]
Fillet Radius at Base of Step (bs): Not Applicable
Unsupported Length (L): 400 [mm]
Reduced Diameter Length (Ls): Not Applicable
Minimum Tip Thickness (t): 6.4 [mm] (Not representative of tip allowance)
Protruding Length (PL): 182.47 [mm] (47% of Pipe ID) Representation of Thermowell Dimensions
Von Mises Stress Limit: 1.65e+08 [Pa] Steady State Stress at V (Smax): 5.43e+06 [Pa]
Material Density (ρm): 8860 [kg/m3] Cyclic Stress at VIR (So, max): Not Applicable
Dynamic Stress at V (So, max): Not Applicable (Reduced Diameter)
Frequency
Scruton Number (Nsc): 0.04 Max Allowable Stem Pressure (Pc): 4.38e+07 [Pa]
Frequency Limit: 0.4 Max Allowable Tip Pressure (Pt): 7.95e+08 [Pa]
In-situ Natural Freq (fnc): 115.9 [Hz]
Strouhal Frequency (fs): 33.8 [Hz]
Frequency Ratio (fs/fnc): 0.29
Thermowell Calculation Tool, Software Version: TCTP2_R_2.6.00 Form Rev P 10 May 2017
Thermowell Calculation Report
This report is only valid with respect to thermowells produced and supplied by Emerson Automation Solutions in accordance with our exacting quality standards.
Customer Data
Company Name: PT Control Systems Arena Para Nusa Project Name: Pekerjaan EPC
Requestor Name: Insan Gaufuan Customer Drawing:
Analyst: Nesmar Noble Thermowell Model Code: 114CM0300PAK2SC060AQ5Q8R21XW
Reviewer: Customer Purchase Order:
Emerson Sales Order: Emerson Sales Order Line: Preliminary Report
Other Information / Notes: Max tip thickness = 7.9mm; Complete Project Name: Pekerjaan EPC Proyek Pembangunan Terminal LPG Refrigerated Tj Sekong
Process Data
Tag Name: TT-6041 Dynamic Fluid Viscosity (μ): 0.1557 [cP]
Process Fluid Velocity (V): 2.25 [m/s] Pressure (P): 12 [Kg/cm2-g] (13.03 [Kg/cm2-a])
Thermowell Dimensions
Mounting Configuration: RF-Flanged-Partial Penetration Weld
Process Connection: 2" Class 300
Stem Material: ASTM A 479 GR 316/316L
Stem Style: Tapered Shank
Root Diameter (A): 26.5 [mm]
Tip Diameter (B): 18 [mm]
Bore Diameter (d): 6.6 [mm]
Fillet Radius at Root (b): 4 [mm]
Fillet Radius at Base of Step (bs): Not Applicable
Unsupported Length (L): 300 [mm]
Reduced Diameter Length (Ls): Not Applicable
Minimum Tip Thickness (t): 6.4 [mm] (Not representative of tip allowance)
Protruding Length (PL): 82.23 [mm] (32% of Pipe ID) Representation of Thermowell Dimensions
Von Mises Stress Limit: 2.02e+08 [Pa] Steady State Stress at V (Smax): 1.80e+06 [Pa]
Material Density (ρm): 8030 [kg/m3] Cyclic Stress at VIR (So, max): Not Applicable
Dynamic Stress at V (So, max): Not Applicable (Reduced Diameter)
Frequency
Scruton Number (Nsc): 0.06 Max Allowable Stem Pressure (Pc): 5.35e+07 [Pa]
Frequency Limit: 0.4 Max Allowable Tip Pressure (Pt): 9.72e+08 [Pa]
In-situ Natural Freq (fnc): 229.0 [Hz]
Strouhal Frequency (fs): 23.8 [Hz]
Frequency Ratio (fs/fnc): 0.10
Thermowell Calculation Tool, Software Version: TCTP2_R_2.6.00 Form Rev P 10 May 2017
Thermowell Calculation Report
This report is only valid with respect to thermowells produced and supplied by Emerson Automation Solutions in accordance with our exacting quality standards.
Customer Data
Company Name: PT Control Systems Arena Para Nusa Project Name: Pekerjaan EPC
Requestor Name: Insan Gaufuan Customer Drawing:
Analyst: Nesmar Noble Thermowell Model Code: 114CM0335PAK2SC060AQ5Q8R21XW
Reviewer: Customer Purchase Order:
Emerson Sales Order: Emerson Sales Order Line: Preliminary Report
Other Information / Notes: Max tip thickness = 7.9mm; Complete Project Name: Pekerjaan EPC Proyek Pembangunan Terminal LPG Refrigerated Tj Sekong
Process Data
Tag Name: TT-7041 Dynamic Fluid Viscosity (μ): 0.1563 [cP]
Process Fluid Velocity (V): 1.59 [m/s] Pressure (P): 12 [Kg/cm2-g] (13.03 [Kg/cm2-a])
Thermowell Dimensions
Mounting Configuration: RF-Flanged-Partial Penetration Weld
Process Connection: 2" Class 300
Stem Material: ASTM A 479 GR 316/316L
Stem Style: Tapered Shank
Root Diameter (A): 26.5 [mm]
Tip Diameter (B): 18 [mm]
Bore Diameter (d): 6.6 [mm]
Fillet Radius at Root (b): 4 [mm]
Fillet Radius at Base of Step (bs): Not Applicable
Unsupported Length (L): 335 [mm]
Reduced Diameter Length (Ls): Not Applicable
Minimum Tip Thickness (t): 6.4 [mm] (Not representative of tip allowance)
Protruding Length (PL): 116.69 [mm] (38% of Pipe ID) Representation of Thermowell Dimensions
Von Mises Stress Limit: 2.02e+08 [Pa] Steady State Stress at V (Smax): 1.70e+06 [Pa]
Material Density (ρm): 8030 [kg/m3] Cyclic Stress at VIR (So, max): Not Applicable
Dynamic Stress at V (So, max): Not Applicable (Reduced Diameter)
Frequency
Scruton Number (Nsc): 0.06 Max Allowable Stem Pressure (Pc): 5.35e+07 [Pa]
Frequency Limit: 0.4 Max Allowable Tip Pressure (Pt): 9.72e+08 [Pa]
In-situ Natural Freq (fnc): 184.5 [Hz]
Strouhal Frequency (fs): 16.7 [Hz]
Frequency Ratio (fs/fnc): 0.09
Thermowell Calculation Tool, Software Version: TCTP2_R_2.6.00 Form Rev P 10 May 2017