Professional Documents
Culture Documents
8 - Abaqus Cae Users Manual PDF
8 - Abaqus Cae Users Manual PDF
0-1
The information in this document is subject to change without notice and should not be construed as a
commitment by Hibbitt, Karlsson & Sorensen, Inc.
Hibbitt, Karlsson & Sorensen, Inc. assumes no responsibility for any errors that may appear in this
document.
The software described in this document is furnished under license and may be used or copied only in
accordance with the terms of such license.
No part of this document may be reproduced in any form or distributed in any way without prior
written agreement with Hibbitt, Karlsson & Sorensen, Inc.
Printed in U.S.A.
All Rights Reserved.
This electronic book is being displayed using DynaText software produced by Inso Corporation.
DynaText is a registered trademark of Inso Corporation.
ABAQUS is a registered trademark of Hibbitt, Karlsson & Sorensen, Inc. The following are
trademarks of Hibbitt, Karlsson & Sorensen, Inc.: ABAQUS/ADAMS; ABAQUS/Aqua;
ABAQUS/CAE; ABAQUS/CAT; ABAQUS/C-MOLD; ABAQUS/Design; ABAQUS/Explicit;
ABAQUS/Post; ABAQUS/Safe; ABAQUS/Standard; ABAQUS/USA; ABAQUS/Viewer; and the
Hibbitt, Karlsson & Sorensen, Inc. logo.
This release of ABAQUS may contain a capability licensed under U.S. Patent 5,920,491. Hibbitt,
Karlsson & Sorensen, Inc. may also have other patents or pending patent applications, trademarks,
copyrights, or other intellectual property rights covering subject matter in this document. The
furnishing of this document does not give you any license to the patents, trademarks, copyrights, or
other intellectual property rights except as expressly provided in any written license agreement from
Hibbitt, Karlsson & Sorensen, Inc.
0-2
Hitachi is a registered trademark of Hitachi, Ltd.
IBM RS/6000 is a trademark of IBM.
Intel is a registered trademark of the Intel Corporation.
NEC is a trademark of the NEC Corporation.
PostScript is a registered trademark of Adobe Systems, Inc.
Silicon Graphics is a registered trademark of Silicon Graphics, Inc.
SUN is a registered trademark of Sun Microsystems, Inc.
TEX is a trademark of the American Mathematical Society.
UNIX and Motif are registered trademarks and X Window System is a trademark of The Open Group
in the U.S. and other countries.
Windows NT is a registered trademark of the Microsoft Corporation.
ABAQUS/CAE incorporates portions of the ACIS software by SPATIAL TECHNOLOGY INC. ACIS
is a registered trademark of SPATIAL TECHNOLOGY INC.
This release of ABAQUS on Windows NT includes the diff program obtained from the Free Software
Foundation. You may freely distribute the diff program and/or modify it under the terms of the GNU
Library General Public License as published by the Free Software Foundation, Inc., 59 Temple Place,
Suite 330, Boston, MA 02111-1307 USA.
This release of ABAQUS/CAE includes lp_solve, a simplex-based code for linear and integer
programming problems by Michel Berkelaar of Eindhoven University of Technology, Eindhoven, the
Netherlands.
Python, copyright 1991-1995 by Stichting Mathematisch Centrum, Amsterdam, The Netherlands. All
Rights Reserved. Permission to use, copy, modify, and distribute the Python software and its
documentation for any purpose and without fee is hereby granted, provided that the above copyright
notice appear in all copies and that both that copyright notice and this permission notice appear in
supporting documentation, and that the names of Stichting Mathematisch Centrum or CWI or
Corporation for National Research Initiatives or CNRI not be used in advertising or publicity
pertaining to distribution of the software without specific, written prior permission.
All other brand or product names are trademarks or registered trademarks of their respective
companies or organizations.
0-3
General conversion factors (to five significant digits)
Quantity U.S. unit SI equivalent
Length 1 in 0.025400 m
1 ft 0.30480 m
1 mile 1609.3 m
2
Area 1 in 0.64516 ´ 10-3 m2
1 ft2 0.092903 m 2
1 acre 4046.9 m2
Volume 1 in3 0.016387 ´ 10-3 m3
1 ft 3 0.028317 m 3
1 US gallon 3.7854 ´ 10-3 m3
Conversion factors for stress analysis
Quantity U.S. unit SI equivalent
Density 1 slug/ft3 = 1 lbf s2/ft4 515.38 kg/m3
1 lbf s2/in4 10.687 ´ 106 kg/m3
Energy 1 ft lbf 1.3558 J (N m)
Force 1 lbf 4.4482 N (kg m/s2)
2
Mass 1 slug = 1 lbf s /ft 14.594 kg (N s2/m)
1 lbf s2/in 175.13 kg
Power 1 ft lbf/s 1.3558 W (N m/s)
Pressure, Stress 2
1 psi (lbf/in ) 6894.8 Pa (N/m2)
Conversion factors for heat transfer analysis
Quantity U.S. unit SI equivalent
Conductivity 1 Btu/ft hr °F 1.7307 W/m °C
1 Btu/in hr °F 20.769 W/m °C
Density 1 lbm/in3 27680. kg/m3
Energy 1 Btu 1055.1 J
Heat flux density 1 Btu/in 2 hr 454.26 W/m2
Power 1 Btu/hr 0.29307 W
Specific heat 1 Btu/lbm °F 4186.8 J/kg °C
Temperature 1 °F 5/9 °C
Temp °F 9/5 ´ Temp °C + 32°
9/5 ´ Temp °K - 459.67°
Important constants
Constant U.S. unit SI unit
Absolute zero -459.67 °F -273.15 °C
Acceleration of gravity 32.174 ft/s 2 9.8066 m/s2
Atmospheric pressure 14.694 psi 0.10132 ´ 106 Pa
Stefan-Boltzmann 0.1714 ´ 10-8 Btu/hr ft2
5.669 ´ 10-8 W/m2 °K4
constant °R4
where °R = °F + 459.67 where °K = °C + 273.15
Approximate properties of mild steel at room temperature
Quantity U.S. unit SI unit
Conductivity 28.9 Btu/ft hr °F 50 W/m °C
2.4 Btu/in hr °F
Density 15.13 slug/ft3 (lbf s2/ft4) 7800 kg/m3
0.730 ´ 10-3 lbf s2/in4
0-4
0.282 lbm/in 3
Elastic modulus 30 ´ 106 psi 207 ´ 109 Pa
Specific heat 0.11 Btu/lbm °F 460 J/kg °C
Yield stress 30 ´ 103 psi 207 ´ 106 Pa
0-5
UNITED STATES
Hibbitt, Karlsson & Sorensen, Inc. Hibbitt, Karlsson & Sorensen (Michigan),
Inc.
1080 Main Street 14500 Sheldon Road, Suite 160
Pawtucket, RI 02860-4847 Plymouth, MI 48170-2408
Tel: 401 727 4200 Tel: 734 451 0217
Fax: 401 727 4208 Fax: 734 451 0458
E-mail: info@abaqus.com, E-mail: hksmi@abaqus.com
support@abaqus.com
http://www.abaqus.com
Hibbitt, Karlsson & Sorensen (West), ABAQUS Solutions Northeast, LLC
Inc.
39221 Paseo Padre Parkway, Suite F Summit Office Park, West Building
Fremont, CA 94538-1611 300 Centerville Road, Suite 209W
Tel: 510 794 5891 Warwick, RI 02886-0201
Fax: 510 794 1194 Tel: 401 739 3637
E-mail: hkswest@abaqus.com Fax: 401 739 3302
E-mail: support@abaqus-sn.com
AC Engineering, Inc.
1440 Innovation Place
West Lafayette, IN 47906-1000
Tel: 765 497 1373
Fax: 765 497 4444
E-mail: info@aceng.com
ARGENTINA AUSTRALIA
KB Engineering S. R. L. Compumod Pty. Ltd.
Florida 274, Of. 37 Level 13, 309 Pitt Street
(1005) Buenos Aires, Argentina Sydney 2000
Tel: +54 11 4393 8444 P.O. Box A807
Fax: +54 11 4326 2424 Sydney South 1235
E-mail: sanchezsarmiento@arnet.com.ar Tel: 02 9283 2577
Fax: 02 9283 2585
E-mail: support@compumod.com.au
http://www.compumod.com.au
AUSTRIA BENELUX
VOEST-ALPINE STAHL LINZ GmbH ABAQUS Benelux BV
Department WFE Huizermaatweg 576
Postfach 3 1276 LN Huizen
A-4031 Linz The Netherlands
Tel: 0732 6585 9919 Tel: +31 35 52 58 424
Fax: 0732 6980 4338 Fax: +31 35 52 44 257
E-mail: edwin.till@voest.co.at E-mail: support@abaqus.nl
CHINA CZECH REPUBLIC AND SLOVAK
REPUBLIC
Advanced Finite Element Services ASATTE
Department of Engineering Mechanics Technická 4, 166 07 Praha 6
Tsinghua University Czech Republic
Beijing 100084, P. R. China Tel: 420 2 24352654
Tel: 010 62783986 Fax: 420 2 33322482
0-6
Fax: 010 62771163 E-mail: asatte@biomed.fsid.cvut.cz
E-mail: zhuangz@mail.tsinghua.edu.cn
FRANCE GERMANY
ABAQUS Software, s.a.r.l. ABACOM Software GmbH
7, rue de la Patte d'Oie Theaterstraße 30-32
78000 Versailles D-52062 Aachen
Tel: 01 39 24 15 40 Tel: 0241 474010
Fax: 01 39 24 15 45 Fax: 0241 4090963
E-mail: support@abaqus.fr E-mail: abacom@abacom.de
ITALY JAPAN
Hibbitt, Karlsson & Sorensen Italia, Hibbitt, Karlsson & Sorensen, Inc.
s.r.l.
Viale Certosa, 1 3rd Floor, Akasaka Nihon Building
20149 Milano 5-24, Akasaka 9-chome
Tel: 02 39211211 Minato-ku
Fax: 02 39211210 Tokyo, 107-0052
E-mail: infohks@abaqus.it Tel: 03 5474 5817
Fax: 03 5474 5818
E-mail: hksj@hksj.co.jp
KOREA MALAYSIA
Hibbitt, Karlsson & Sorensen Korea, Inc. Compumod Sdn Bhd
Suite 306, Sambo Building #33.03 Menara Lion
13-2 Yoido-Dong, Youngdeungpo-ku 165 Jalan Ampang
Seoul, 150-010 50450 Kuala Lumpur
Tel: 02 785 6707/8 Tel: 3 466 2122
Fax: 02 785 6709 Fax: 3 466 2123
E-mail: hotline@abaqus.co.kr E-mail: hotline@compumod.com.my
NEW ZEALAND POLAND
Matrix Applied Computing Ltd. BudSoft Sp. z o.o.
P.O. Box 56-316, Auckland 61-807 Pozna
Courier: Unit 2-5, 72 Dominion Road, Sw. Marcin 58/64
Mt Eden,
Auckland Tel: 61 852 31 19
Tel: +64 9 623 1223 Fax: 61 852 31 19
Fax: +64 9 623 1134 E-mail: budsoft@man.poznan.pl
E-mail: hks-support@matrix.co.nz
SINGAPORE SOUTH AFRICA
Compumod (Singapore) Pte Ltd Finite Element Analysis Services (Pty) Ltd.
#17-05 Asia Chambers Suite 20-303C, The Waverley
20 McCallum Street Wyecroft Road
Singapore 069046 Mowbray 7700
Tel: 223 2996 Tel: 021 448 7608
Fax: 226 0336 Fax: 021 448 7679
E-mail: E-mail: abaqus@feas.co.za
compumod@mbox2.singnet.com.sg
SPAIN SWEDEN
Principia Ingenieros Consultores, S.A. FEM-Tech AB
Velázquez, 94 Pilgatan 8
28006 Madrid SE-721 30 Västerås
0-7
Tel: 91 209 1482 Tel: 021 12 64 10
Fax: 91 575 1026 Fax: 021 18 12 44
E-mail: abaqus@principia.es E-mail: femtech@femtech.se
TAIWAN UNITED KINGDOM
APIC Hibbitt, Karlsson & Sorensen (UK) Ltd.
7th Fl., 131 Sung Chiang Road The Genesis Centre
Taipei, 10428 Science Park South, Birchwood
Tel: 02 25083066 Warrington, Cheshire WA3 7BH
Fax: 02 25077185 Tel: 01925 810166
E-mail: cae@apic.com.tw Fax: 01925 810178
E-mail: hotline@hks.co.uk
0-8
This section lists various resources that are available for help with using ABAQUS, including
technical and systems support, training seminars, and documentation.
Support
HKS offers both technical (engineering) support and systems support for ABAQUS. Technical and
systems support are provided through the nearest local support office. You can contact our offices by
telephone, fax, electronic mail, or regular mail. Information on how to contact each office is listed in
the front of each ABAQUS manual. Support information is also available by visiting the ABAQUS
Home Page on the World Wide Web (details are given below). When contacting your local support
office, please specify whether you would like technical support (you have encountered problems
performing an ABAQUS analysis) or systems support (ABAQUS will not install correctly, licensing
does not work correctly, or other hardware-related issues have arisen).
We welcome any suggestions for improvements to the support program or documentation. We will
ensure that any enhancement requests you make are considered for future releases. If you wish to file a
complaint about the service or products provided by HKS, refer to the ABAQUS Home Page.
Technical support
HKS technical support engineers can assist in clarifying ABAQUS features and checking errors by
giving both general information on using ABAQUS and information on its application to specific
analyses. If you have concerns about an analysis, we suggest that you contact us at an early stage, since
it is usually easier to solve problems at the beginning of a project rather than trying to correct an
analysis at the end.
Please have the following information ready before calling the technical support hotline, and include it
in any written contacts:
- The version numbers for ABAQUS/Standard and ABAQUS/Explicit are given at the top of the
data (.dat) file.
- The version numbers for ABAQUS/CAE and ABAQUS/Viewer can be found by selecting
Help->On version from the main menu bar.
- The version number for ABAQUS/CAT is given at the top of the input ( .inp) file as well as
the data file.
- The version numbers for ABAQUS/ADAMS and ABAQUS/C-MOLD are output to the
screen.
- The version number for ABAQUS/Safe is given under the ABAQUS logo in the main
window.
0-9
· The symptoms of any problems, including the exact error messages, if any.
When calling for support about a specific problem, any available ABAQUS output files may be helpful
in answering questions that the support engineer may ask you.
The support engineer will try to diagnose your problem from the model description and a description
of the difficulties you are having. Frequently, the support engineer will need model sketches, which
can be faxed to HKS or sent in the mail. Plots of the final results or the results near the point that the
analysis terminated may also be needed to understand what may have caused the problem.
If the support engineer cannot diagnose your problem from this information, you may be asked to send
the input data. The data can be sent by means of e-mail, tape, or disk. Please check the ABAQUS
Home Page at www.abaqus.com for the media formats that are currently accepted.
All support calls are logged into a database, which enables us to monitor the progress of a particular
problem and to check that we are resolving support issues efficiently. If you would like to know the log
number of your particular call for future reference, please ask the support engineer. If you are calling to
discuss an existing support problem and you know the log number, please mention it so that we can
consult the database to see what the latest action has been and, thus, avoid duplication of effort. In
addition, please give the receptionist the support engineer's name (or include it at the top of any e-mail
correspondence).
Systems support
HKS systems support engineers can help you resolve issues related to the installation and running of
ABAQUS, including licensing difficulties, that are not covered by technical support.
You should install ABAQUS by carefully following the instructions in the ABAQUS Site Guide. If
you encounter problems with the installation or licensing, first review the instructions in the ABAQUS
Site Guide to ensure that they have been followed correctly. If this does not resolve the problems, look
on the ABAQUS Home Page under Technical Support for information about known installation
problems. If this does not address your situation, please contact your local support office. Send
whatever information is available to define the problem: error messages from an aborted analysis or a
detailed explanation of the problems encountered. Whenever possible, please send the output from the
abaqus info=env and abaqus info=sys commands.
0-10
· Benchmark timing documents
· Newsletters
Addresses for other offices and representatives are listed in the front of each manual.
Training
All HKS offices offer regularly scheduled public training classes.
The Introduction to ABAQUS/Standard and ABAQUS/Explicit seminar covers basic usage and
nonlinear applications, such as large deformation, plasticity, contact, and dynamics. Workshops
provide as much practical experience with ABAQUS as possible.
The Introduction to ABAQUS/CAE seminar discusses modeling, managing simulations, and viewing
results with ABAQUS/CAE. "Hands-on" workshops are complemented by lectures.
Advanced seminars cover topics of interest to customers with experience using ABAQUS, such as
engine analysis, metal forming, fracture mechanics, and heat transfer.
We also provide training seminars at customer sites. On-site training seminars can be one or more days
in duration, depending on customer requirements. The training topics can include a combination of
material from our introductory and advanced seminars. Workshops allow customers to exercise
ABAQUS on their own computers.
0-11
For a schedule of seminars see the ABAQUS Home Page, or call HKS or your local HKS
representative.
Documentation
The following documentation and publications are available from HKS, unless otherwise specified, in
printed form and through our online documentation server. For more information on accessing the
online books, refer to the discussion of execution procedures in the user's manuals.
In addition to the documentation listed below, HKS publishes two newsletters on a regular schedule:
ABAQUS/News and ABAQUS/Answers. ABAQUS/News includes topical information about program
releases, training seminars, etc. ABAQUS/Answers includes technical articles on particular topics
related to ABAQUS usage. These newsletters are distributed at no cost to users who wish to subscribe.
Please contact your local ABAQUS support office if you wish to be added to the mailing list for these
publications. They are also archived in the Reference Shelf on the ABAQUS Home Page.
Training Manuals
Getting Started with ABAQUS/Explicit: This document is a self-paced tutorial designed to help
new users become familiar with using ABAQUS/Explicit. It begins with the basics of modeling in
ABAQUS, so no prior knowledge of ABAQUS is required. A number of fully worked examples
provide practical guidelines for performing explicit dynamic analyses, such as drop tests and metal
forming simulations, with ABAQUS/Explicit.
Lecture Notes: These notes are available on many topics to which ABAQUS is applied. They are
used in the technical seminars that HKS presents to help users improve their understanding and
usage of ABAQUS (see the "Training" section above for more information about these seminars).
While not intended as stand-alone tutorial material, they are sufficiently comprehensive that they
can usually be used in that mode. The list of available lecture notes is included in the
Documentation Price List.
User's Manuals
ABAQUS/Explicit User's Manual: This volume contains a complete description of the elements,
material models, procedures, input specifications, etc. It is the basic reference document for
ABAQUS/Explicit.
0-12
ABAQUS/CAE User's Manual: This reference document for ABAQUS/CAE includes three
comprehensive tutorials as well as detailed descriptions of how to use ABAQUS/CAE for model
generation, analysis, and results evaluation.
ABAQUS/Viewer User's Manual: This basic reference document for ABAQUS/Viewer includes
an introductory tutorial as well as a complete description of how to use ABAQUS/Viewer to
display your model and results.
ABAQUS/ADAMS User's Manual: This document describes how to install and how to use
ABAQUS/ADAMS, an interface program that creates ABAQUS models of ADAMS components
and converts the ABAQUS results into an ADAMS modal neutral file that can be used by the
ADAMS/Flex program. It is the basic reference document for the ABAQUS/ADAMS program.
ABAQUS/CAT User's Manual: This document describes how to install and how to use
ABAQUS/CAT, an interface program that creates an ABAQUS input file from a CATIA model
and postprocesses the analysis results in CATIA. It is the basic reference document for the
ABAQUS/CAT program.
ABAQUS/C-MOLD User's Manual: This document describes how to install and how to use
ABAQUS/C-MOLD, an interface program that translates finite element mesh, material property,
and initial stress data from a C-MOLD analysis to an ABAQUS input file.
ABAQUS/Safe User's Manual: This document describes how to install and how to use
ABAQUS/Safe, an interface program that calculates fatigue lives and fatigue strength reserve
factors from finite element models. It is the basic reference document for the ABAQUS/Safe
program. The theoretical background to fatigue analysis is contained in the Modern Metal Fatigue
Analysis manual (available only in print).
Using ABAQUS Online Documentation: This online manual contains instructions on using the
ABAQUS online documentation server to read the manuals that are available online.
ABAQUS Release Notes: This document contains brief descriptions of the new features available
in the latest release of the ABAQUS product line.
ABAQUS Site Guide: This document describes how to install ABAQUS and how to configure
the installation for particular circumstances. Some of this information, of most relevance to users,
is also provided in the user's manuals.
Examples Manuals
ABAQUS Example Problems Manual: This volume contains more than 75 detailed examples
designed to illustrate the approaches and decisions needed to perform meaningful linear and
nonlinear analysis. Typical cases are large motion of an elastic-plastic pipe hitting a rigid wall;
inelastic buckling collapse of a thin-walled elbow; explosive loading of an elastic, viscoplastic thin
ring; consolidation under a footing; buckling of a composite shell with a hole; and deep drawing of
a metal sheet. It is generally useful to look for relevant examples in this manual and to review
them when embarking on a new class of problem.
0-13
ABAQUS Benchmarks Manual: This volume (available online and, if requested, in print)
contains over 200 benchmark problems and standard analyses used to evaluate the performance of
ABAQUS; the tests are multiple element tests of simple geometries or simplified versions of real
problems. The NAFEMS benchmark problems are included in this manual.
ABAQUS Verification Manual: This online-only volume contains more than 5000 basic test
cases, providing verification of each individual program feature (procedures, output options,
MPCs, etc.) against exact calculations and other published results. It may be useful to run these
problems when learning to use a new capability. In addition, the supplied input data files provide
good starting points to check the behavior of elements, materials, etc.
Reference Manuals
ABAQUS Keywords Manual: This volume contains a complete description of all the input
options that are available in ABAQUS/Standard and ABAQUS/Explicit.
ABAQUS Theory Manual: This volume (available online and, if requested, in print) contains
detailed, precise discussions of all theoretical aspects of ABAQUS. It is written to be understood
by users with an engineering background.
ABAQUS Scripting Manual: This online manual provides a description of the ABAQUS
Command Language and a command reference that lists the syntax of each command. The manual
describes how commands can be used to create and analyze ABAQUS/CAE models, to view the
results of the analysis, and to automate repetitive tasks. It also contains information on using the
ABAQUS Command Language or C++ as an application programming interface (API).
ABAQUS Input Files: This online manual contains all the input files that are included with the
ABAQUS release and referred to in the ABAQUS Example Problems Manual, the ABAQUS
Benchmarks Manual, and the ABAQUS Verification Manual. They are listed in the order in which
they appear in the manuals, under the title of the problem that refers to them. The input file
references in the manuals hyperlink directly to this book.
0-14
Getting started with ABAQUS/CAE
Tutorials
This section contains three tutorials that lead you through the modeling process. In the first
tutorial you create a simple model, analyze it, and then view the results. The second tutorial is
more complex and illustrates how parts, sketches, datum geometry, and partitions work
together and how you assemble part instances. The third tutorial demonstrates how you can
use the Visualization module to display your results in a variety of formats and how you can
customize the display.
0-15
Using this manual
· Part III, "Working with ABAQUS/CAE model databases, models, and files"
· Part IV, "Creating and analyzing a model using the ABAQUS/CAE modules"
Appendix A, "Keyword support," provides tables that you can use to determine which ABAQUS/CAE
module embodies the functionality of a particular ABAQUS keyword, as well as whether a particular
keyword is supported. Appendix B, "Visualization module limitations," lists the ABAQUS elements
and output variables that are not supported by the Visualization module. If you are familiar with
ABAQUS/Post, Appendix C, "Transitioning to the Visualization module from ABAQUS/Post,"
explains the relationships between the Visualization module functions and the corresponding
ABAQUS/Post commands. This appendix also lists the functionality in ABAQUS/Post that is not yet
available in the Visualization module.
1-16
Using this manual
· Text you enter from the keyboard or that ABAQUS/CAE outputs: crankshaft_steel,
1.35E10
· Text indicating that the user has a choice: odb_file, Options->plot mode
The following terms describe actions you perform using the mouse:
Click
Press and quickly release the mouse button. Unless otherwise specified, the instruction ``click''
means that you should click mouse button 1.
Drag
Press and hold down mouse button 1 while moving the mouse.
Point
Move the mouse until the cursor is over the desired item.
Select
1-17
Using this manual
[Shift]+Click
Press and hold the [Shift] key, click mouse button 1, and then release the [Shift] key.
[Ctrl]+Click
Press and hold the [Ctrl] key, click mouse button 1, and then release the [Ctrl] key.
ABAQUS/CAE is designed for use with a 3-button mouse. Accordingly, this manual refers to mouse
buttons 1, 2, and 3 as shown in Figure 1-1. However, you can use ABAQUS/CAE with a 2-button
mouse as follows:
· The two mouse buttons are equivalent to mouse buttons 1 and 3 on a 3-button mouse.
1-18
A tutorial: Creating and analyzing a simple model
You will then analyze the beam and plot the resulting stresses and displacements. The entire tutorial
takes approximately 90 minutes to complete.
If you are following the tutorial but are unsure how to proceed at any point, click the highlighted and
underlined text in the help window to view more extensive documentation of the task you are
attempting. Clicking highlighted text (a hyperlink) takes you to a different section of the
ABAQUS/CAE User's Manual; clicking the Go Back button in the toolbar across the top of this
window returns you to your original point in "Getting started with ABAQUS/CAE. For example, click
``Overview of the main window,'' Section 5.2 to see detailed information on the components of the
main window and click the Go Back button to return here.
The following topics are covered:
2-19
A tutorial: Creating and analyzing a simple model
· ``Applying a boundary condition and a load to the model, '' Section 2.9
For the cantilever beam tutorial, you will enter the following ABAQUS/CAE modules and perform the
following tasks:
Part
Sketch a two-dimensional profile and create a part representing the cantilever beam.
2-20
A tutorial: Creating and analyzing a simple model
Property
Define the material properties and other section properties of the beam.
Assembly
Assemble the model and create sets.
Step
Configure the analysis procedure and output requests.
Load/BC/IC
Apply loads and boundary conditions to the beam.
Mesh
Mesh the beam.
Job
Create a job and submit it for analysis.
Visualization
View the results of the analysis.
Although the Module list under the toolbar lists the modules in a logical sequence, you can move back
and forth between modules at will. However, certain obvious restrictions apply; for example, you
cannot assign section properties to geometry that has not yet been created.
A completed model contains everything that ABAQUS/CAE needs to generate an input file and start
the analysis. ABAQUS/CAE uses a model database to store your models. When you start
ABAQUS/CAE, the Start Session dialog box allows you to create a new, empty model database in
memory. After you start ABAQUS/CAE, you can save your model database to a disk by selecting
File->Save from the main menu bar; to retrieve it from a disk, select File->Open.
For a complete listing of which module generates a particular keyword, see ``ABAQUS keyword
browser table,'' Section A.1.
· Part III, "Working with ABAQUS/CAE model databases, models, and files."
2-21
A tutorial: Creating and analyzing a simple model
Tip: To open a separate window containing any of the figures in the online documentation, click
the figure itself.
2. From the Start Session dialog box that appears, select Start Tutorial.
The ABAQUS/CAE main window and the online documentation window, turned to the chapter
"Getting Started with ABAQUS/CAE," appear.
3. In the Find text field at the bottom of the help window, type any word that appears in the text of
the help window and press [Enter].
All occurrences of the word you typed are highlighted. You can enter any phrase to search for, and
the help system will locate precisely that phrase; for example, searching for the word "element"
yields different results than searching for the word "elements." Use the [*] character as a wildcard;
for example, searching for "element*" will find occurrences of the words "element," "elements,"
"elemental," and "elementary."
2-22
A tutorial: Creating and analyzing a simple model
7. From the main menu bar of the book window, select File->Close View .
The book window disappears.
8. In the upper-left corner of the context-sensitive help window, double-click the close button.
The help window disappears.
· Context-sensitive help is available for every item in the ABAQUS/CAE main window and in all its
dialog boxes.
· You can search individual help windows or the entire online manual for information.
· The online book windows provide a hyperlinked table of contents for easy navigation throughout
the book.
Figure 2-3 Messages and instructions are displayed in the prompt area.
Click the cancel button to cancel the current task. Click the backup button to cancel the current step in
the task and return to the previous step.
To create the cantilever beam:
2-23
A tutorial: Creating and analyzing a simple model
2. From the Start Session dialog box that appears, select Start Tutorial.
3. In the Module list located under the toolbar, click Part to enter the Part module.
The cursor changes to an hourglass while the Part module loads. When the Part module has
finished loading, it displays the Part module toolbox in the left side of the ABAQUS/CAE main
window. The toolbox contains a set of icons that allow expert users to bypass the menus in the
main menu bar. Each module displays its own set of tools in the module toolbox. As you select
items from the main menu bar, the corresponding tool is highlighted in the module toolbox so that
you can learn its location.
4. From the main menu bar, select Part->Create to create a new part.
The Create Part dialog box appears. ABAQUS/CAE also displays text in the prompt area near the
bottom of the window to guide you through the procedure.
You use the Create Part dialog box to name the part; to choose its modeling space, type, and base
feature; and to set the approximate size. You can edit and rename a part after you create it, but you
cannot change its modeling space, type, or base feature.
5. Name the part Beam. Accept the default settings of a three-dimensional, deformable body and a
solid, extruded base feature. In the Approximate size text field, type 300.
The following aspects of the Sketcher help you sketch the desired geometry:
· The Sketcher grid helps you position the cursor and align objects in the viewport.
· Dashed lines indicate the X- and Y-axes of the sketch and intersect at the origin of the sketch.
· A triad in the lower-left corner of the viewport indicates the relationship between the sketch
plane and the orientation of the part.
· When you select a sketching tool, ABAQUS/CAE displays the X- and Y-coordinates of the
cursor in the upper-left corner of the viewport.
7. To sketch the profile of the cantilever beam, you need to draw a rectangle. To select the rectangle
drawing tool, do the following:
2-24
A tutorial: Creating and analyzing a simple model
a. Note the small black triangles at the base of some of the toolbox icons. These triangles
indicate the presence of hidden icons that can be revealed. Click the Line tool in the
upper-right corner of the Sketcher toolbox, but do not release mouse button 1. Additional
icons appear, as shown below.
b. Without releasing mouse button 1, drag the cursor along the set of icons that appear until
you reach the rectangle tool. Then release the mouse button to select that tool.
The rectangle drawing tool appears in the Sketcher toolbox with a pink background indicating that
you selected it. ABAQUS/CAE displays prompts in the prompt area to guide you through the
procedure.
a. Notice that as you move the cursor around the viewport, ABAQUS/CAE displays the
cursor's X- and Y-coordinates in the upper-left corner.
c. Move the cursor to the opposite corner (100, -10) so that the rectangle is twenty grid
squares long and two grid squares high as shown in Figure 2-4.
e. Click mouse button 2 anywhere in the viewport to finish using the rectangle tool.
Note: If you are a Windows NT user with a 2-button mouse, press both mouse buttons simultaneously whenever
you are asked to press mouse button 2.
2-25
A tutorial: Creating and analyzing a simple model
9. If you make a mistake while using the Sketcher, you can delete lines in your sketch, as explained
in the following procedure:
e. Click mouse button 2 in the viewport to finish using the Delete tool.
10. From the prompt area (near the bottom of the main window), click Done to exit the Sketcher.
Note: If you don't see the Done button in the prompt area, continue to click mouse button 2 in the viewport until it appears.
11. Because you are creating an extruded part, ABAQUS/CAE displays a text field in the prompt area
asking you to define the distance through which the sketch should be extruded. In the text field,
erase the default value of 30.0 and type a value of 25.0. You can either press [Enter] or click
mouse button 2 in the viewport to accept this value.
ABAQUS/CAE displays an isometric view of the new part, as shown in Figure 2-5.
To help you orient the cantilever beam during the modeling process, ABAQUS/CAE displays a
triad in the lower-left corner indicating the orientation of the X-, Y-, and Z-axes.
12. Before you continue the tutorial, save your model in a model database file.
2-26
A tutorial: Creating and analyzing a simple model
a. From the main menu bar, select File->Save. The Save Model Database As dialog box
appears.
b. Type a name for the new model database in the Selection field, and click OK. You do not
need to include the file extension; ABAQUS/CAE automatically appends .cae to the file
name.
ABAQUS/CAE stores the model database in a new file and returns to the Part module.
The title bar of the ABAQUS/CAE window displays the path and name of the model
database. You should always save your model database at regular intervals (for example,
each time you switch modules); ABAQUS/CAE does not save your model database
automatically.
· You use the Part module to create parts. When you create a part, you name it and choose its type,
modeling space, base feature, and approximate size.
· ABAQUS/CAE automatically enters the Sketcher when you create or edit a part. You use the
Sketcher to draw the two-dimensional profiles of parts.
· Click and drag toolbox icons to reveal and select hidden icons.
· Click mouse button 2 in the viewport to indicate you have finished selecting items or using a
tool.
1. In the Module list located under the toolbar, select Property to enter the Property module.
The cursor changes to an hourglass while the Property module loads.
2. From the main menu bar, select Material->Create to create a new material.
2-27
A tutorial: Creating and analyzing a simple model
When you select a material option, the appropriate data entry form appears below the menu.
5. Type a value of 209.E3 for Young's modulus and a value of 0.3 for Poisson's ratio in the
respective fields, as shown in Figure 2-7. Use [Tab] to move between cells.
Figure 2-7 Entering data values for the elastic material properties.
· You can use the Property module to create a material and define its properties.
2-28
A tutorial: Creating and analyzing a simple model
· You can simply select the region from the part and assign the section to the selected region.
· You can use the Set toolset to create a homogeneous set containing the region and assign the
section to the set.
For the cantilever beam tutorial you will create a single homogeneous solid section that you will assign
to the beam by selecting the beam from the viewport. The solid section will contain a reference to the
material Steel that you just created.
d. Click Continue.
The Edit Section dialog box appears.
a. Accept the default selection of Steel for the Material associated with the section.
c. Click OK.
· You can use the Property module to create a section and define its category and type (solid and
homogeneous, respectively, in this case).
2-29
A tutorial: Creating and analyzing a simple model
· Since the section refers to the material, the material must be defined first.
2. Click anywhere on the beam to select the region to which the section will be applied.
ABAQUS/CAE highlights the entire beam.
3. Click mouse button 2 in the viewport or click Done in the prompt area to accept the selected
geometry.
The Assign Section dialog box appears containing a list of existing sections.
4. Accept the default selection of BeamSection as the section, and click OK.
ABAQUS/CAE assigns the solid section to the beam and closes the Assign Section dialog box.
· When you assign a section to a region of a part, the region takes on the material properties
associated with the section.
2-30
A tutorial: Creating and analyzing a simple model
ABAQUS/CAE positions the instance so that the origin of the sketch that defined the rectangular
profile of the beam overlays the origin of the assembly's default coordinate system.
To assemble the model:
1. In the Module list located under the toolbar, click Assembly to enter the Assembly module.
The cursor changes to an hourglass while the Assembly module loads.
4. In the toolbar near the top of the window, click the rotate view manipulation tool, .
When you move the mouse back into the viewport, a circle appears.
5. Drag the mouse in the viewport to rotate the model and examine it from all sides. Click mouse
button 2 to exit rotate mode.
6. Several other tools (pan , magnify , zoom , and auto-fit ) are also available in
the toolbar to help you examine your model. Experiment with each of these tools until you are
comfortable with them. Use the context-sensitive help system to obtain any additional information
you require about these tools.
· A model contains only one assembly. The assembly is composed of instances of parts positioned in
a global coordinate system.
· The view manipulation tools available in the toolbar allow you to examine your model.
· An initial step, in which you will apply a boundary condition that constrains one end of the
cantilever beam.
2-31
A tutorial: Creating and analyzing a simple model
· A general, static analysis step, in which you will apply a pressure load to the top face of the beam.
ABAQUS/CAE generates the initial step automatically, but you must use the Step module to create the
analysis step yourself. The Step module also allows you to request output for any steps in the analysis.
1. In the Module list located under the toolbar, click Step to enter the Step module.
The cursor changes to an hourglass while the Step module loads.
4. From the list of available general procedures in the Create Step dialog box, select Static, General
if it is not already selected and click Continue.
The Edit Step dialog box appears with the default settings for a general, static step.
5. The Basic tab is selected by default. In the Description field, type Load the top of the
beam.
6. Click the Incrementation tab, and accept the default time incrementation settings.
7. Click the Other tab to see its contents; you can accept the default values provided for the step.
8. Click OK to create the step and to exit the Edit Step dialog box.
· ABAQUS/CAE generates the initial step automatically, but you must use the Step module to create
additional steps.
· You use the step editor to configure each step you create.
2-32
A tutorial: Creating and analyzing a simple model
· Select the variables that ABAQUS will write to the output database.
· Select the section points for which ABAQUS will generate data.
· Select the region of the model for which ABAQUS will generate data.
· Change the frequency at which ABAQUS will write data to the output database.
For the cantilever beam tutorial, you will simply examine the output requests and accept the default
configuration.
To examine your output requests:
2. Review the default output request that ABAQUS/CAE generates for the Static, General step you
created and named Beamload.
The variables from the categories shown on the Field output tabbed page of the Output Database
Request Manager will be output. If you change an output request, you can always return to the
default settings by clicking Defaults at the bottom of the Output Database Request Manager .
3. At the bottom of the Output Database Request Manager , click Edit to view more detailed
information about the output request.
The field output editor appears.
4. Click the arrows next to each output variable category to see exactly which variables will be
output. The boxes next to each category title allow you to see at a glance whether all variables in
that category will be output. A filled box indicates that all variables are output, while a partially
filled box indicates that only some variables will be output.
Based on the selections shown at the bottom of the dialog box, data will be generated at every
default section point in the model and will be written to the output database after every increment
during the analysis.
2-33
A tutorial: Creating and analyzing a simple model
you must use the field output editor or the history output editor to modify those requests. Clicking the Dismiss button simply
closes the Output Database Request Manager dialog box. Conversely, Cancel buttons appear in dialog boxes that allow you
to make changes. Clicking Cancel closes the dialog box without saving your changes.
· When you create a step, ABAQUS/CAE generates a default output request for the step.
· You use the Output Database Request Manager to examine which categories of data will be
output.
· You invoke the field and history output editors from the Output Database Request Manager to
select the variables that ABAQUS/CAE will write to the output database during the analysis, as
well as the frequency at which they are written and the regions and section points from which they
are written.
· A boundary condition that constrains one end of the cantilever beam in the X-, Y-, and
Z-directions; the boundary condition is applied during the initial step.
· A load that you apply to the top face of the beam; the load is applied during the general analysis
step.
1. In the Module list located under the toolbar, click Load/BC/IC to enter the Load/BC/IC module.
The cursor changes to an hourglass while the Load/BC/IC module loads.
2-34
A tutorial: Creating and analyzing a simple model
b. From the list of steps, select Initial as the step in which the boundary condition will be
activated.
d. In the Type for Selected Step list, accept Displacement/Rotation as the default type
selection, and click Continue.
ABAQUS/CAE displays prompts in the prompt area to guide you through the procedure.
4. You will fix the face at the left end of the cantilever beam; the desired face is shown in Figure 2-8.
By default, when you click in a region that overlaps more than one face ABAQUS/CAE selects the
face that is ``closest'' to the screen. To select the face at the left end of the cantilever beam you
need to turn off this default behavior and cycle through the valid selections. Do the following:
b. From the Options dialog box that appears, toggle off the closest object tool .
2-35
A tutorial: Creating and analyzing a simple model
5. Click mouse button 2 in the viewport or click Done in the prompt area to indicate that you have
finished selecting. The selection options return to their default behavior.
The Edit Boundary Condition dialog box appears. When you are defining a boundary condition
in the initial step, all six degrees of freedom are unconstrained by default.
a. Toggle on U1, U2, and U3, since only the translational degrees of freedom need to be
constrained.
b. Click OK to create the boundary condition and to close the dialog box.
ABAQUS/CAE displays three arrows at each corner and midpoint on the selected face to
indicate the constrained degrees of freedom.
· Prescribed conditions, such as loads and boundary conditions, are step-dependent objects, which
means that you must specify the step or steps in which they become active.
· Managers are useful for reviewing and modifying the status of prescribed conditions in each step.
2-36
A tutorial: Creating and analyzing a simple model
b. From the list of steps, select Beamload as the step in which the load will be applied.
e. Click Continue.
ABAQUS/CAE displays prompts in the prompt area to guide you through the procedure.
3. In the viewport, select the top face of the beam as the surface to which the load will be applied.
The desired face is shown by the gridded face in Figure 2-9.
4. Click mouse button 2 or click Done in the prompt area in the viewport to indicate that you have
finished selecting regions.
The Edit Load dialog box appears.
b. Accept the default Amplitude selection--ABAQUS/CAE will ramp the load during the
step.
2-37
A tutorial: Creating and analyzing a simple model
6. Examine the Load Manager and note that the new load is ``Created'' (activated) in the general
analysis step Beamload.
· You use the Load/BC/IC module to create loads and to define where the load is applied to the
assembly.
· Loads can be propagated across steps; the Load Manager indicates the steps during which a load
is applied.
1. In the Module list located under the toolbar, click Mesh to enter the Mesh module.
The cursor changes to an hourglass while the Mesh module loads.
3. In the dialog box, accept Hex as the default Element Shape selection.
2-38
A tutorial: Creating and analyzing a simple model
5. Click OK to assign the mesh controls and to close the dialog box.
ABAQUS/CAE will use the structured meshing technique to create a mesh of hexahedral-shaped
elements.
2. In the dialog box, accept the following default selections that control the elements that are
available for selection:
3. In the lower portion of the dialog box, examine the element shape options. A brief description of
the default element selection is available at the bottom of each tabbed page.
Since the model is a three-dimensional solid, only three-dimensional solid element
types--hexahedral on the Hex tabbed page, triangular prism on the Wedge page, and tetrahedral on
the Tet page--are shown.
4. Click the Hex tab, and choose Incompatible modes from the list of Element Controls.
A description of the element type C3D8I appears at the bottom of the dialog box. ABAQUS/CAE
will now associate C3D8I elements with the elements in the mesh.
5. Click OK to assign the element type and to close the dialog box.
· Although you can create a mesh at any point after creating the assembly, you typically do it after
configuring the rest of the model, since items such as loads, boundary conditions, and steps depend
on the underlying geometry, not the mesh.
· You can assign the element type either before or after you create the mesh.
2-39
A tutorial: Creating and analyzing a simple model
1. From the main menu bar, select Seed->Instance to seed the part instance.
The prompt area displays the default element size that ABAQUS/CAE will use to seed the part
instance. This default element size is based on the size of the part instance.
2. In the prompt area, accept the default element size of 10, and press Enter or click mouse button 2
in the viewport.
ABAQUS/CAE applies the seeds to the part instance, as shown in Figure 2-10.
You can gain more control of the resulting mesh by seeding each edge of the partinstance
individually.
2-40
A tutorial: Creating and analyzing a simple model
4. From the main menu bar, select Mesh->Instance to mesh the part instance.
5. From the buttons in the prompt area, click Yes to confirm that you want to mesh the part instance.
ABAQUS/CAE meshes the part instance and displays the resulting mesh, as shown in Figure 2-11.
· You select the number of seeds based on the element size or on the number of elements that you
want along an edge.
· You use seeds to define the approximate position of nodes in your final mesh.
1. In the Module list located under the toolbar, click Job to enter the Job module.
The cursor changes to an hourglass while the Job module loads.
2-41
A tutorial: Creating and analyzing a simple model
The Create Job dialog box appears with a list of the models in the model database.
6. Click the tabs to review the default settings in the job editor. Click OK to accept all the default job
settings and to close the dialog box.
7. From the main menu bar, select Job->Manager to start the Job Manager.
The Job Manager appears and displays a list of your jobs, the model associated with each job, the
type of analysis, and the status of the job.
8. From the buttons on the right edge of the Job Manager, click Submit to submit your job for
analysis.
After you submit your job, the information in the Status column updates to indicate the job's
status. The Status column for the cantilever beam tutorial shows one of the following:
· Completed when the analysis is complete, and the output has been written to the output
database.
· Aborted if ABAQUS/CAE finds a problem with the input file or the analysis and aborts the
analysis. In addition, ABAQUS/CAE reports the problem in the message area.
9. When the job completes successfully, you are ready to view the results of the analysis with the
Visualization module. From the buttons on the right edge of the Job Manager, click Results.
ABAQUS/CAE loads the Visualization module, opens the output database created by the job, and
displays a representation of the model.
· You use the Job Manager to submit jobs and to monitor the status of a job.
2-42
A tutorial: Creating and analyzing a simple model
1. After you click Results in the Job module's Job Manager, ABAQUS/CAE loads the
Visualization module, opens Deform.odb, and displays a fast plot of the model, as shown in
Figure 2-12.
· The version of ABAQUS/Standard or ABAQUS/Explicit that was used to generate the output
database.
By default, ABAQUS/CAE plots the last step and the last frame of your analysis. Buttons that
allow you to control which analysis results are plotted are available in the prompt area.
2. From the main menu bar, select Plot->Undeformed Shape to view an undeformed shape plot.
2-43
A tutorial: Creating and analyzing a simple model
The model's color changes to green to indicate that this is an undeformed shape plot, not a fast
plot.
3. From the main menu bar, select Plot->Deformed Shape to view a deformed shape plot.
4. Click the auto-fit tool so that the entire plot is rescaled to fit in the viewport, as shown in
Figure 2-13.
5. From the main menu bar, select Plot->Contours to view a contour plot of the von Mises stress, as
shown in Figure 2-14.
6. Click the Contour Options button at the bottom-right corner of the prompt area to change the
appearance of the current plot.
2-44
A tutorial: Creating and analyzing a simple model
The Contour Plot Options dialog box appears. You can use this dialog box to, for example, turn
on node and element labeling, change the deformation scale factor of the underlying model, or
adjust the contour intervals. (To change general plot options, such as turning the legend off or on,
select View->Viewport Annotations from the main menu bar.)
8. For a contour plot the default variable displayed depends on the analysis procedure; in this case,
the default variable is the von Mises stress. From the main menu bar, select Result->Field Output
to examine the variables that are available for display.
ABAQUS/CAE displays the Field Output dialog box; click the Primary Variable tab to choose
which variable to display and to select the invariant or component of interest. By default, the
Mises invariant of the Stress components at integration points variable is selected.
· You use the Visualization module to read the output database generated by your analysis and to
view the results.
· You can select the variable to display from the data in the output database, and you can also select
the increment being displayed.
· You can display the results in several modes--undeformed, deformed, and contour.
· You can control the appearance of the display in each mode, independent of other modes.
You have now finished the first tutorial. The second tutorial introduces additional techniques to create
and analyze a model; for example, you will create and assemble multiple part instances and define
contact. The third tutorial covers the capabilities of the Visualization module in more detail.
2-45
A tutorial: Using additional techniques to create and analyze a model
· It consists of three different parts and three different part instances rather than just one. This
tutorial illustrates how you position instances of these parts to create the assembly and how you
define contact between surfaces of the assembly.
· It includes parts that you will draw using advanced sketching techniques. You will learn how
sketches, datum geometry, and partitions combine to define the features that make up individual
parts. You will also learn how you can modify a part by editing a feature and how modified parts
are regenerated.
As in the first tutorial, you will apply section properties, loads, and boundary conditions to the model;
you will also mesh the model, configure the analysis, and run the analysis job. At the end of the tutorial
you will view your analysis results. The entire tutorial takes approximately three hours to complete.
This tutorial assumes that you are familiar with the techniques described in the first tutorial, including
the following:
· Using the view manipulation tools to rotate and zoom an object in the viewport.
· Using the mouse to select menu items, toolbox items, and items within the viewport.
· Using hyperlinks to see more detailed help in the online documentation and clicking the Go Back
button in the toolbar across the top of the book window to return you to your original point in
"Getting started with ABAQUS/CAE."
3.1 Overview
During the tutorial you will create an assembly composed of a hinge held together by a pin. The
assembled part instances and the final mesh are illustrated in Figure 3-1.
3-46
A tutorial: Using additional techniques to create and analyze a model
· A flange that extends from the cube. The flange also includes a large-diameter hole through which
the pin is inserted.
3-47
A tutorial: Using additional techniques to create and analyze a model
1. Start ABAQUS/CAE, and create a new model database. If you are viewing this tutorial online,
resize your windows so that you can follow the tutorial and see the ABAQUS/CAE main window.
2. In the Module list located under the toolbar, click Part to enter the Part module.
The cursor changes to an hourglass while the Part module loads, and the Part module toolbox
appears on the left side of the main window.
The triad in the lower-left corner of the viewport indicates the orientation of the X-, Y-, and Z-axes.
You can turn off this triad by selecting View->Viewport Annotations from the main menu bar
and toggling off the Show triad option. (The triad is sometimes turned off for clarity in the figures
in this tutorial.)
3. From the main menu bar, select Part->Create to create a new part.
The Create Part dialog box appears.
The text in the prompt area asks you to fill out the Create Part dialog. ABAQUS/CAE always
displays prompts in the prompt area to guide you through a procedure.
3-48
A tutorial: Using additional techniques to create and analyze a model
5. In the Approximate size text field, type 0.2. You will be modeling the hinge using meters for the
unit of length, and its overall length is 0.14 meters; therefore, 0.2 meters is a sufficiently large
approximate size for the part. Click Continue to create the part.
The Sketcher starts and displays the toolbox on the left side of the main window. ABAQUS/CAE
uses the approximate size of the part to compute the default sheet size--0.2 meters in this example.
In addition, in this example the Sketcher draws 20 grid lines on the sheet, and the distance between
each grid line is 0.01 meters. (You probably see fewer than 20 grid lines because the sheet extends
beyond your viewport.)
6. From the Sketcher toolbox, select the rectangle tool . (Click and drag on the line toolbox
icon to reveal the hidden rectangle tool.)
7. While you are sketching, ABAQUS/CAE displays the cursor position in the upper-left corner of
the viewport containing the Sketcher grid. Find the origin of the sketch at (0, 0); then move the
cursor to (-0.02, -0.02), and click mouse button 1 to define the first corner of the rectangle. Click
mouse button 1 again at (0.02, 0.02) to define the opposite corner.
Important: To complete this tutorial successfully, it is important that you use the dimensions
stated and do not deviate from the example; otherwise, you will find it difficult to assemble
the model.
8. Click mouse button 2 in the viewport to exit the rectangle tool. Click mouse button 2 again to exit
the Sketcher.
Tip: Clicking mouse button 2 in the viewport has the same effect as clicking the default
button in the prompt area--Done in this instance.
9. In the text box in the prompt area, type an extrusion depth of 0.04 and press [Enter].
ABAQUS/CAE exits the Sketcher and displays the base feature, a cube, as shown in Figure 3-2.
· The default spacing of the Sketcher grid depends on the value you enter in the Approximate size
text field in the Create Part dialog box.
· Dashed lines on the Sketcher grid indicate the X- and Y-axes of the sketch and the origin. While
you are drawing, ABAQUS/CAE displays the cursor position in the upper-left corner of the
viewport containing the Sketcher grid.
3-49
A tutorial: Using additional techniques to create and analyze a model
2. Select a face to define the sketching plane, and select the extrusion direction.
a. Select the face at the front of the cube, as shown in Figure 3-4.
Figure 3-4 Select the gridded face to define the sketching plane. The arrow indicates the
correct extrusion direction.
ABAQUS/CAE displays an arrow indicating the extrusion direction. The default extrusion
direction for a solid is always out of the solid. ABAQUS/CAE draws the arrow wherever
you clicked on the face to select it during the previous step; as a result, the arrow may not
appear in the same location shown in Figure 3-4.
b. In the prompt area, click Flip to set the extrusion direction into the cube. Click OK when
the arrow indicates the desired extrusion direction, as shown in Figure 3-4.
3. Select an edge that will appear vertical and on the right side of the sketch, as shown in Figure 3-5.
Figure 3-5 Select the indicated edge to position the part correctly in the Sketcher.
3-50
A tutorial: Using additional techniques to create and analyze a model
The Sketcher starts and displays the outline of the base feature as reference geometry. The sketch
of the flange that you will create is illustrated in Figure 3-6.
5. Draw the three sides of a rectangle, as shown in Figure 3-7. The four vertices should be at (0.04,
0.02), (0.02, 0.02), (0.02, -0.02), and (0.04, -0.02).
3-51
A tutorial: Using additional techniques to create and analyze a model
Tip: If you make a mistake while sketching, use the Sketcher undo or delete
tools to correct your error.
6. Click mouse button 2 in the viewport to exit the connected lines tool. From the Sketcher toolbox,
7. Click at the center of the arc and at each vertex. ABAQUS/CAE draws the arc in a clockwise
direction from the first vertex to the second. The resulting arc is shown in Figure 3-8.
8. From the Sketcher toolbox, select the circle tool . Click at (0.04, 0) to locate the center of
the circle; click at (0.05, 0) to define the circle.
Note: When you mesh a part, ABAQUS/CAE places nodes wherever vertices appear along an edge; therefore, the location of
the vertex on the circumference of the circle influences the final mesh. Placing the vertex at (0.05, 0) results in a high-quality
mesh.
3-52
A tutorial: Using additional techniques to create and analyze a model
9. From the dimension tools in the Sketcher toolbox, select the radial dimension tool .
11. Position the dimension text and click mouse button 1 to accept the location, as shown in Figure
3-9. You can position dimension text at any convenient location in a sketch, although you cannot
subsequently move the text after you have positioned it.
12. Click mouse button 2 in the viewport to exit the radius dimension tool. Click mouse button 2 again
to exit the Sketcher.
13. From the buttons that appear in the prompt area, select Blind to indicate that you will provide the
depth of the extrusion.
14. In the text box in the prompt area, type an extrusion depth of 0.02 and press [Enter].
ABAQUS/CAE displays the part composed of the cube and the flange. ``Silhouette'' edges appear
in gray indicating curved faces of the flange. Silhouette edges are purely a visual aid; they are not
true edges and cannot be selected.
15. Use the auto-fit view manipulation tool to resize the figure to fit in the viewport.
· You create parts by adding features to the base feature; in this example the cube is the base feature
and the flange is added to it.
· When you add a feature, you must select a face on which to sketch the profile of the feature.
3-53
A tutorial: Using additional techniques to create and analyze a model
2. From the lower-right corner of the main window, click Feature List.
ABAQUS/CAE displays the Feature List dialog box, showing each feature's Name and Status. In
this example you have created two solid extrusion features: the base feature (the cube), whose
Name is Solid extrude-1, and the flange, whose Name is Solid extrude-2. When you select a
feature from the Feature List dialog box, ABAQUS/CAE highlights the selected feature in the
viewport.
3. From the Feature List dialog box, select the flange ( Solid extrude-2) and click OK.
Note: Instead of using the Feature List dialog box, you could have also selected a feature to edit directly from the viewport.
ABAQUS/CAE displays the feature editor. For an extruded solid you can change the extrusion
depth, and you can edit the profile sketch.
5. From the edit tools in the Sketcher toolbox, select the edit dimension value tool .
7. In the text box in the prompt area, type a new radius of 0.012 and press [Enter].
ABAQUS/CAE changes the radius of the circle in the sketch only.
8. Click mouse button 2 to exit the edit dimension tool. Click mouse button 2 again to exit the
Sketcher.
ABAQUS/CAE again displays the feature editor.
9. Click OK to regenerate the flange with the modified radius and to exit the feature editor.
The flange hole is enlarged to the new radius dimension.
Note: In some circumstances regenerating a feature causes dependent features to fail. In such a case ABAQUS/CAE asks if
you want to save your changes and suppress the features that failed to regenerate, or if you want to revert to the unmodified
3-54
A tutorial: Using additional techniques to create and analyze a model
· You can edit features by modifying the sketch of the feature or a parameter associated with the
feature, such as an extrusion depth.
· Dimensioning a sketch and modifying the dimensions allow you to refine a part.
Figure 3-10 Isometric shaded view of the hinge with the lubrication hole.
Creating the hole in the desired location requires an appropriate datum plane on which to sketch the
profile of the extruded cut, as shown in Figure 3-11.
Figure 3-11 Two-dimensional view of the datum plane's position with respect to the hinge piece.
3-55
A tutorial: Using additional techniques to create and analyze a model
You sketch a circle on the datum plane, which is tangent to the flange, and ABAQUS/CAE extrudes
the circle normal to the datum plane and normal to the flange to create the lubrication hole.
There are three operations involved in creating the datum plane:
· Creating a datum plane through the datum point on the circumference and normal to the datum
axis.
2. Create a datum point along the curved edge of the flange through which the datum plane will pass.
From the Create Datum dialog box, choose the Point datum type.
3. From the list of methods, select Use parameter, and click Apply.
Note: What is the difference between the OK and Apply buttons? When you click OK, the Create Datum dialog box closes
before you create the datum. When you click Apply, the Create Datum dialog box remains open while you create the datum
and is available for you to create the next datum. Click OK if you want to create only a single datum; click Apply if you want to
create several pieces of datum geometry before moving on to a new procedure.
4. Select the curved edge, as shown in Figure 3-12. Note the direction of the arrow indicating an
increasing edge parameter from 0.0 to 1.0.
Figure 3-12 Create a datum point along the curved edge of the flange.
3-56
A tutorial: Using additional techniques to create and analyze a model
5. In the text box in the prompt area, enter a normalized edge parameter of 0.25, and press [Enter].
ABAQUS/CAE creates a datum point along the selected edge.
6. Create a datum axis that will define the normal to the datum plane. From the Create Datum dialog
box, choose the Axis datum type. Select the 2 points method, and click Apply.
ABAQUS/CAE highlights the points that can be used to create the datum axis.
7. Select the point at the center of the hole (created when you sketched the hole's profile) and the
datum point on the curved edge.
ABAQUS/CAE displays a datum axis passing through the two points, as shown in Figure 3-13.
8. The final step is to create the datum plane normal to the datum axis. From the Create Datum
dialog box, choose the Plane datum type. Select the Point and normal method, and click Apply.
9. Select the datum point on the curved edge as the point through which the datum plane will pass.
10. Select the datum axis as the edge that will be normal to the datum plane.
ABAQUS/CAE creates the datum plane, as shown in Figure 3-14.
3-57
A tutorial: Using additional techniques to create and analyze a model
· If a suitable sketch plane does not exist, you can use the Datum toolset to create one.
· The Datum toolset allows you to create datum points, axes, and planes.
· Click OK in a dialog box to perform the selected operation and to close the dialog box; click
Apply to leave the dialog box open while performing the selected operation. Click Cancel to close
the dialog box without performing an operation.
Figure 3-15 A datum point indicates the center of the lubrication hole.
3-58
A tutorial: Using additional techniques to create and analyze a model
2. Create a datum point along the second curved edge of the flange. From the Create Datum dialog
box, choose the Point datum type.
3. From the list of methods, select Use parameter, and click Apply.
4. Select the second curved edge of the flange, as shown in Figure 3-16.
6. From the list of methods, select Midway between 2 points , and click Apply.
2. Click the boundary of the datum plane to select it as the plane on which to sketch.
3-59
A tutorial: Using additional techniques to create and analyze a model
3. Select the direction of the extruded cut to be into the part, and click OK.
4. Select the top rear edge of the cube as the edge that will appear vertical and on the right side of the
sketch, as shown in Figure 3-17.
Figure 3-17 Select the indicated edge to position the part correctly in the Sketcher grid.
The Sketcher starts with the vertices, datums, and edges of the part projected onto the sketch plane
as reference geometry.
Tip: If you are unsure of the relative orientation of the sketch plane and the part, use the
view manipulation tools to rotate and pan them. Use the cycle view manipulation tool to
restore the original view.
6. Select the datum point on the center of the flange to indicate the center of the circle.
9. From the edit tools in the Sketcher toolbox, select the edit dimension value tool .
10. Select the radial dimension of the circle. In the text field that appears in the prompt area, type a
new radius of 0.003, and press [Enter].
The radius of the circle changes.
11. Click mouse button 2 to exit the edit dimension value tool. Click mouse button 2 again to indicate
that you have finished sketching.
3-60
A tutorial: Using additional techniques to create and analyze a model
12. From the buttons in the prompt area, select Up to Face to define the extrusion distance.
ABAQUS/CAE exits the Sketcher and displays an isometric view of the part.
13. Select the cylindrical inner surface of the hole in the part to indicate the face to which to extrude,
as illustrated in Figure 3-18. (Because you can select at most only one face, ABAQUS/CAE does
not ask you to indicate that you have finished selecting.)
ABAQUS/CAE immediately extrudes the sketch from the datum plane to the hole in the flange.
14. From the toolbar, select the shaded display tool , and use the rotation tool to see how the
part and its features are oriented, as shown in Figure 3-19. (For clarity, the datum geometry has
been removed from the view in Figure 3-19 by selecting View->Part Display Options->Datum.)
Tip: After you rotate the part, use the cycle views tool to step through the previous
views (up to a maximum of eight) and to restore the original view.
3-61
A tutorial: Using additional techniques to create and analyze a model
15. Now that you have created the first part of your model, it is a good idea to save your model in a
model database:
a. From the main menu bar, select File->Save. The Save Model Database As dialog box
appears.
b. Type a name for the new model database in the Selection field, and click OK. You do not
need to include the file extension; ABAQUS/CAE appends .cae automatically to the file
name.
ABAQUS/CAE stores the model database in a new file and returns to the Part module.
The name of your model database appears in the main window title bar.
If you find you need you need to interrupt this tutorial, you can save the model database at any
time and exit ABAQUS/CAE. You can then start a new ABAQUS/CAE session and open the
saved model database by selecting File->Open from the main menu bar. The model database will
contain any parts, materials, loads, etc. that you created, and you will be able to continue the
tutorial.
· If you rotate or pan the sketch, use the cycle view manipulation tool to restore the original view.
· Datum geometry that you create on a part can also be used by the Sketcher.
· Creating a material.
You will use the Property module to perform all of these tasks.
3-62
A tutorial: Using additional techniques to create and analyze a model
1. In the Module list located under the toolbar, click Property to enter the Property module.
The cursor changes to an hourglass while the Property module loads.
2. From the main menu bar, select Material->Create to create a new material.
The Create Material dialog box appears.
3. In the Create Material dialog box, name the material Steel, and click Continue.
The material editor appears.
5. In the respective fields in the Elastic data form, type a value of 209.E9 for Young's modulus and
a value of 0.3 for Poisson's ratio.
· You enter material data into tables in the material editor to define the material properties of your
model.
3-63
A tutorial: Using additional techniques to create and analyze a model
c. In the Type list, accept Homogeneous as the default selection, and click Continue.
The section editor appears.
3. In the editor:
b. Accept the default value for Plane stress/strain thickness , and click OK.
· You can choose from all materials that have been defined for the model.
2. Drag a rectangle around the hinge piece to select the entire part.
ABAQUS/CAE highlights all the regions of the part.
3. Click mouse button 2 to indicate that you have finished selecting the regions to be assigned the
section.
The Assign Section dialog box appears containing a list of existing sections. SolidSection is
selected by default since there are no other sections currently defined.
4. In the Assign Section dialog box, accept the default selection of SolidSection, and click OK.
ABAQUS/CAE assigns the section to the part.
· By assigning a section to a region of a part, you associate a material with that region.
· You can choose from all solid sections that have been defined for the model.
3-64
A tutorial: Using additional techniques to create and analyze a model
hole.
3. In the text box in the Copy Part dialog box, type Hinge-solid, and click OK.
ABAQUS/CAE creates a copy of the hinge piece and names the copy Hinge-solid. The copy of
the hinge piece includes the section from the original hinge piece.
· When you copy a part, the copy contains all the features that defined the original part, as well as
any sections that were assigned to it.
3. From the toolbar across the top of the main ABAQUS/CAE window, select the wireframe display
4. Select the datum point on the edge of the flange, as shown in Figure 3-20.
Tip: You may need to use the zoom and magnify tools to locate the datum point.
3-65
A tutorial: Using additional techniques to create and analyze a model
5. When you delete a selected feature, ABAQUS/CAE asks whether you also want to delete any
features that depend on the feature being deleted. The feature being deleted is called the ``parent''
feature, and its dependent features are called ``children.'' ABAQUS/CAE highlights all the features
that it will delete if the parent feature is deleted. From the buttons in the prompt area, click Yes to
delete the datum point and all its children.
ABAQUS/CAE deletes the datum point. Because they were dependent on the datum point,
ABAQUS/CAE also deletes the datum axis, the datum plane, and the lubrication hole.
Important: You cannot recover deleted features; however, you can temporarily remove a feature by suppressing it using the
Feature Manipulation toolset.
· When you delete a feature from a part, ABAQUS/CAE also deletes any features that depend on the
feature being deleted. These dependent features are called children.
1. From the main menu bar, select Part->Create to create a new part.
The Create Part dialog box appears.
2. Name the part Pin. Choose a three-dimensional body as before, but change the type to Analytical
rigid and the base feature shape to Revolved shell.
3-66
A tutorial: Using additional techniques to create and analyze a model
4. From the Sketcher toolbox, select the connected lines tool . Sketch a line to the right of the
axis running from (0.010, 0.030) to (0.010, -0.030).
5. Dimension the horizontal distance from the line to the axis, and change the distance to 0.012.
When you modify the dimension, you must select the vertices at each end of the line to move. (Use
[Shift]+[Click] to select both vertices.) The sketch and the resulting shaded part are shown in
Figure 3-21.
Figure 3-21 Create the pin by revolving an analytical rigid surface about an axis.
6. Click mouse button 2 to exit the edit dimension value tool, and click mouse button 2 again to exit
the Sketcher.
ABAQUS/CAE displays the revolved, analytical rigid surface. Note that silhouette edges appear in
gray indicating the curved face of the pin.
· When you create a part, you can create a deformable part, a discrete rigid surface, or an analytical
rigid surface. You cannot subsequently change the type of the part.
· When you sketch the profile of an axisymmetric part, the axis of symmetry appears as a
construction line. Your sketch cannot cross the axis of symmetry.
3-67
A tutorial: Using additional techniques to create and analyze a model
You can either select the reference point from the part in the viewport, or you can enter its coordinates.
For the tutorial you will select the reference point from the viewport, as shown in Figure 3-22.
· When you create a rigid surface, you must assign a rigid body reference point to it.
· You can click the part to select the reference point, or you can enter its coordinates.
3-68
A tutorial: Using additional techniques to create and analyze a model
position a selected instance relative to the global coordinate system. For the tutorial you will keep the
hinge with the lubrication hole fixed and move the second hinge and the pin relative to it.
· An instance of the hinge piece with the lubrication hole removed-- Hinge-solid.
1. In the Module list located under the toolbar, click Assembly to enter the Assembly module.
The cursor changes to an hourglass while the Assembly module loads.
· When you create a part instance, the default position is based on the sketch of the base feature.
· A graphic indicates the origin and the orientation of the global coordinate system in the Assembly
module.
3-69
A tutorial: Using additional techniques to create and analyze a model
instance of the hinge piece with the lubrication hole, you ask ABAQUS/CAE to offset the new
instance along the X-axis.
To create an instance of the solid hinge piece:
1. From the Create Instance dialog box, toggle on Auto-offset from other instances.
The auto-offset function prevents new part instances from overlapping existing instances.
2. From the Create Instance dialog box, select Hinge-solid and click OK.
ABAQUS/CAE closes the dialog box, creates the new instance, and applies an offset along the
X-axis that separates the two hinges, as shown in Figure 3-23. (The datum geometry has been
removed from the shaded view for clarity by selecting View->Assembly Display
Options->Datum.)
Figure 3-23 Create an instance of each hinge piece, and apply an offset to position them in the
viewport.
· When you create an instance, you can ask ABAQUS/CAE to offset the new instance along the
X-axis so that it does not overlap any existing instances.
3-70
A tutorial: Using additional techniques to create and analyze a model
Parallel Face
The movable instance moves until the two selected faces are parallel.
Face to Face
The movable instance moves until the two selected faces are parallel and a specified clearance
from each other.
Parallel Edge
The movable instance moves until the two selected edges are parallel.
Edge to Edge
The movable instance moves until the two selected edges are colinear or a specified distance
from each other.
Coaxial
The movable instance moves until the two selected faces are coaxial.
Contact
The movable instance moves in the direction of a selected vector until the two selected faces
come within a specified distance of each other.
ABAQUS/CAE stores position constraints as features of the assembly, and they can be edited, deleted,
and suppressed. In contrast, translations and rotations are not stored and do not appear in the list of
features. Although position constraints are stored as features, they have no knowledge of each other; as
a consequence, a new position constraint may override a previous position constraint.
In this example you will move the solid hinge piece while the hinge piece with the lubrication hole will
remain fixed. You will apply three types of position constraints to position the two hinge pieces
correctly.
To position the solid hinge piece:
1. First, constrain the solid hinge piece so that the two flanges face each other. From the main menu
bar, select Constraint->Face to Face.
2. Select the face of the solid hinge piece shown in Figure 3-24.
3-71
A tutorial: Using additional techniques to create and analyze a model
3. Select the face of the hinge piece with the lubrication hole shown in Figure 3-25.
ABAQUS/CAE displays red arrows on each selected face; the movable instance will be positioned
so that the arrows point in the same direction. You can change the direction of the arrow on the
movable instance if necessary.
4. From the prompt area, click Flip to change the direction of the arrow. Click OK when the arrows
point toward each other.
5. In the text box that appears in the prompt area, type the clearance (0.04) that will remain between
the two parts, as measured along the normal to the selected face of the fixed part, and press
[Enter].
ABAQUS/CAE rotates the solid hinge piece so that the two selected faces are parallel to each
other and 0.04 meters apart, as shown in Figure 3-26.
Figure 3-26 Position 1: Constrain the flange of the solid hinge piece to face the flange of the
3-72
A tutorial: Using additional techniques to create and analyze a model
The two pieces overlap because the position of the solid hinge piece is not fully determined by the
position constraint you have applied. You will need to apply two more position constraints to
obtain the desired position.
6. Next, align the two flange holes. From the main menu bar, select Constraint->Coaxial.
7. Select the flange hole on the solid hinge piece, as shown in Figure 3-27. (You may find it helpful
to display the wireframe view of the two pieces.)
8. Select the flange hole on the hinge piece with the lubrication hole, as shown in Figure 3-28.
3-73
A tutorial: Using additional techniques to create and analyze a model
9. From the prompt area, click Flip to change the direction of the arrow. Click OK when the arrow
points downward.
ABAQUS/CAE positions the two hinge pieces so that the two flange holes are coaxial.
10. Use the rotate tool to look at the top view of the two pieces. Notice that the two flanges are
now overlapping, as shown in Figure 3-29.
Figure 3-29 Position 2: Constrain the two flange holes to lie along the same axis.
3-74
A tutorial: Using additional techniques to create and analyze a model
11. Finally, add a constraint to eliminate the overlap between the two flanges. From the main menu
bar, select Constraint->Edge to Edge.
12. Select the straight edge on the solid hinge piece shown in Figure 3-30.
13. Select the corresponding edge of the hinge piece with the lubrication hole, as shown in Figure
3-75
A tutorial: Using additional techniques to create and analyze a model
3-31.
14. From the prompt area, click Flip to change the direction of the arrow. Click OK when the arrows
point in the same direction.
ABAQUS/CAE positions the two hinge pieces so that the two selected edges are colinear, as
shown in Figure 3-32.
Figure 3-32 Final position: Constrain an edge of each hinge piece to lie along the same line.
3-76
A tutorial: Using additional techniques to create and analyze a model
· You position part instances in the Assembly module using a sequence of constraint operations.
2. From the Create Instance dialog box, toggle off Auto-offset from other instances and create an
instance of the pin.
3. Constrain the pin to lie along the same axis as the two flange holes. Use the Constraint->Coaxial
menu as you did when you aligned the two flange holes in the previous section. (You can select
either of the flange holes as the cylindrical surface of the fixed instance.)
ABAQUS/CAE will position the pin as shown in Figure 3-33.
Figure 3-33 Align the pin to be coaxial with the two flange holes.
3-77
A tutorial: Using additional techniques to create and analyze a model
5. Select Distance from the list of General Queries, and click OK.
6. The Distance query allows you measure the X-, Y-, and Z-components of the vector connecting
two selected points. You need to determine the distance between the end of the pin and the hinge
containing the lubrication hole; the two points to select are illustrated in Figure 3-34.
a. To define one end of the vector, select a point on the circumference of the hole in the
flange containing the lubrication hole.
b. To define the other end of the vector, select the vertex on the pin that is inside the hinge
containing the lubrication hole.
ABAQUS/CAE displays the vector distance between the two selected points along with
the X-, Y-, and Z-components of the vector in the message area. You will translate the pin
along the Z-axis; the Z-component of the distance is 0.01 meters. You want to position the
pin symmetrically between the hinges, so you will translate it 0.02 meters.
3-78
A tutorial: Using additional techniques to create and analyze a model
9. ABAQUS/CAE warns you that translating this part may break the coaxial position constraint that
you have applied to it. Click Yes to continue, since translation in the Z-direction only will not
break the position constraint.
10. In the text boxes in the prompt area, enter a start point for the translation vector of 0,0,0 and an
end point of 0,0,0.02.
ABAQUS/CAE translates the pin a distance of 0.02 along the Z-axis and displays a temporary
image of the new position of the pin.
Note: If the position of a temporary image (colored red) is not correct, you can use the buttons in the prompt area to correct
the problem. Click either the cancel button ( ) to cancel the procedure or the go back button ( ) to step back though the
procedure.
3-79
A tutorial: Using additional techniques to create and analyze a model
analysis steps:
· In the initial step you apply boundary conditions to regions of the model and define contact
between regions of the model.
· In the first general analysis step you allow contact to become established.
· In the second general analysis step you modify two of the boundary conditions applied to the
model and apply a pressure load to one of the hinge pieces.
ABAQUS/CAE creates the initial step by default, but you must create the two analysis steps.
To create the analysis steps:
1. In the Module list located under the toolbar, click Step to enter the Step module.
The cursor changes to an hourglass while the Step module loads.
b. Accept the default procedure type (Static, General), and click Continue.
The step editor appears.
6. Click the Incrementation tab, and delete the value of 1 that appears in the Initial text field. Type a
value of 0.1 for the initial increment size.
8. Use the same technique to create a second general, static step named Load. Enter Apply load
in the description field and an initial increment size of 0.1.
The Load step appears in the Step Manager.
3-80
A tutorial: Using additional techniques to create and analyze a model
· You create analysis steps yourself and use the step editor to control the time incrementation during
the step.
· Managers are available throughout ABAQUS/CAE. You use managers to display a list of the
entities you have defined--steps in the above example--and to help you perform repeated
operations.
· S (Stress components)
By default, ABAQUS/CAE writes the default field output variables from a static, general procedure to
the output database after every increment of a step. In the following procedure you will delete the
request for CDISP during the Load step, since it is not needed for postprocessing. In addition, you will
change the output frequency during the Contact step so that data are written to the output database
once--at the last increment of the step.
3-81
A tutorial: Using additional techniques to create and analyze a model
To edit an output request and to specify the output frequency during the Load step:
2. In the left panel of the dialog box, select the Load step. From the buttons at the bottom of the
Output Database Request Manager , click Edit.
3. From the list of output categories, click the arrow to the left of Contact.
A list of the contact output variables available appears along with a description of each.
4. Click the check box next to CDISP to deselect this variable for output.
The check box next to Contact changes to half-highlighted to indicate that not all variables in this
category will be output.
5. Accept the default selections in the bottom half of the field output editor:
7. From the Output Database Request Manager , select the Contact step and click Edit.
The field output editor appears for the Contact step.
8. Near the bottom of the editor, toggle on The last increment to generate output only during the last
increment of the step.
10. At the bottom of the Output Database Request Manager , click Dismiss to close the dialog box.
· During the analysis, ABAQUS/CAE writes the results to the output database.
· You use the Field output tabbed page of the Output Database Request Manager to request
output of field variables to the output database, and you use the History output page to request
output of history variables.
3-82
A tutorial: Using additional techniques to create and analyze a model
· ABAQUS/CAE creates a default output request when you create a step. You can edit this default,
and you can create new output requests.
· Create contact pairs with contact node sets and surfaces in the Interaction module.
· Request output to either the output database or the status file from specific regions of the model in
the Step module. Output to the status file is also reported back to the Job module in the form of a
continuously updated X-Y plot.
· Display results for specific regions of the model in the Visualization module.
In this example you will define a node set consisting of a single node. You will then be able to monitor
the results for one degree of freedom at that node when you submit your job for analysis later in this
tutorial.
To create a node set and monitor a particular degree of freedom:
3. Select the vertex of the solid hinge piece shown in Figure 3-36.
4. Click Done to indicate that you have finished selecting the geometry for the set.
3-83
A tutorial: Using additional techniques to create and analyze a model
ABAQUS/CAE creates a node set with the name Monitor that contains the node at the vertex
you selected.
· A surface named Pin that includes the outside surface of the pin.
· Two surfaces named Flange-h and Flange-s that include the two flange faces that contact
each other.
· Two surfaces named Inside-h and Inside-s that include the inside surfaces of the flanges
that contact the pin.
1. In the Module list located under the toolbar, click Interaction to enter the Interaction module.
The cursor changes to an hourglass while the Interaction module loads.
2. You will find it helpful to display only one part at a time while you select the surfaces to be
defined.
3-84
A tutorial: Using additional techniques to create and analyze a model
c. Click in the Visible column next to Hinge-hole-1 and Hinge-solid-1, and click
Apply.
5. In the dialog box, name the surface Pin, accept the default Geometry type, and click Continue.
7. Click mouse button 2 in the viewport to indicate that you have finished selecting regions for the
surface.
Arrows appear in the viewport indicating the two sides of the hollow cylinder representing the pin,
as shown in Figure 3-37.
The magenta arrow indicates the outer surface of the pin, and the yellow arrow indicates the inner
surface of the pin. The outer surface contacts the two hinges and is the desired choice.
8. From the buttons in the prompt area, click Magenta to choose the outer surface.
ABAQUS/CAE creates the desired surface called Pin and displays it in the Surface Manager.
3-85
A tutorial: Using additional techniques to create and analyze a model
· Click the Instance tab in the Assembly Display Options dialog box to make part instances
visible or invisible.
· When you create and name a surface, you can select the surface by name in subsequent operations,
such as defining contact.
· When you create a surface on a shell-type structure, you must select which side of the surface is of
interest.
1. From the Assembly Display Options dialog box, change the visibility settings so that only
Hinge-hole-1 is visible.
ABAQUS/CAE displays only the hinge piece with the lubrication hole in the viewport.
3. In the dialog box, name the surface Flange-h, accept the default Geometry type, and click
Continue.
4. On the instance with the lubrication hole, select the face of the flange that contacts the other
flange, as shown by the gridded face in Figure 3-38. (You may need to rotate the view to see this
face clearly.)
5. When you have selected the desired face, click mouse button 2 to confirm your selection.
ABAQUS/CAE creates the desired surface called Flange-h and displays it in the Surface
3-86
A tutorial: Using additional techniques to create and analyze a model
Manager.
6. Create a surface called Inside-h that includes the cylindrical inner surface of the hinge piece
with the lubrication hole, as shown in Figure 3-39. (You may need to zoom in on the view to select
this face.)
8. Use similar techniques to create a surface called Flange-s that contains the corresponding face
of the solid hinge piece's flange.
9. Finally, create a surface called Inside-s that includes the cylindrical inner surface of the solid
hinge piece.
10. From the Surface Manager, click Dismiss to close the manager.
11. Leave the Assembly Display Options dialog box open so that you can continue to display the
part instances as you need them for the rest of the tutorial.
· An interaction called HingePin-hole that defines the contact between the part instance
Hinge-hole-1 and the pin.
3-87
A tutorial: Using additional techniques to create and analyze a model
· An interaction called HingePin-solid that defines the contact between the part instance
Hinge-solid-1 and the pin.
· An interaction called Flanges that defines the contact between the two flanges.
Each of these interactions requires a reference to an interaction property. Interaction properties are
collections of information that help you to define certain types of interactions. You will create a
mechanical interaction property that describes the tangential and normal behavior between all surfaces
as frictionless. You will name this property NoFric and use it in all three of the interactions.
c. Click Continue.
The Edit Contact Property dialog box appears.
3. From the dialog box's menu bar, select Mechanical->Tangential Behavior and accept
Frictionless for the friction formulation.
4. Click OK to save your settings and to close the Edit Contact Property dialog box.
3-88
A tutorial: Using additional techniques to create and analyze a model
c. In the Types for Selected Step list, accept the default selection of Surface-to-surface
contact (Standard).
d. Click Continue.
4. On the far right side of the prompt area, click the Surfaces button.
The Region Selection dialog box appears containing a list of the surfaces that you defined
earlier.
5. In the Region Selection dialog box, select Pin as the master surface, and click Continue.
6. From the buttons in the prompt area, select Surface as the slave type.
7. In the Region Selection dialog box, select Inside-h as the slave surface, and click Continue.
The Edit Interaction dialog box appears.
b. Accept the default Slave Node Adjustment selection of Do not adjust slave nodes .
c. Accept NoFric as the interaction property. (If more properties were defined, you could
click the arrow next to the Interaction property field to see the list of available properties
and select the property of your choice.)
9. Use the same techniques explained in the previous steps to create a similar interaction called
HingePin-solid. Use Pin as the master surface, Inside-s as the slave surface, and
NoFric as the interaction property.
10. Create a similar interaction called Flanges. Use Flange-h as the master surface, Flange-s
as the slave surface, and NoFric as the interaction property.
11. From the Interaction Manager, click Dismiss to close the manager.
· Interactions are step dependent. In this tutorial all interactions are associated with the initial step.
3-89
A tutorial: Using additional techniques to create and analyze a model
· You must select a master surface and a slave surface when creating an interaction.
· You can select master and slave surfaces either by selecting previously created surfaces from a list
or by selecting surfaces directly from the viewport.
· A boundary condition called Fixed that constrains all degrees of freedom at the end of the hinge
piece with the lubrication hole, as shown in Figure 3-40.
· A boundary condition called NoSlip that constrains all degrees of freedom of the pin while
contact is established during the first analysis step. You will modify this boundary condition in the
second analysis step (the step in which the load is applied) so that degrees of freedom 1 and 5 are
unconstrained. Figure 3-41 illustrates this boundary condition applied at the reference point.
3-90
A tutorial: Using additional techniques to create and analyze a model
· A boundary condition called Constrain that constrains all degrees of freedom of a point on the
solid hinge piece during the first analysis step. You will modify this boundary condition in the
second analysis step so that degree of freedom 1 is unconstrained when the load is applied.
· A load called Pressure that you apply to the end of the solid hinge piece during the second
analysis step. Figure 3-42 illustrates the constraint and the pressure load applied to the solid
hinge.
1. In the Module list located under the toolbar, click Load/BC/IC to enter the Load/BC/IC module.
The cursor changes to an hourglass while the Load/BC/IC module loads.
3-91
A tutorial: Using additional techniques to create and analyze a model
d. Click Continue.
The Region Selection dialog box appears.
e. From the right side of the prompt area, click Select in Viewport to select the object
directly from the viewport.
The Region Selection dialog box closes.
5. Select the gridded face shown in Figure 3-43 as the region where the boundary condition will be
applied.
Figure 3-43 Apply a boundary condition to the end of the hinge piece with the lubrication hole.
By default, ABAQUS/CAE selects only objects that are closest to the front of the screen, and you
cannot select the desired face unless you rotate the hinge. However, you can use the selection
options to change this behavior.
b. From the Options dialog box that appears, toggle off the closest object tool .
6. Click mouse button 2 to indicate that you have finished selecting regions.
The Edit Boundary Condition dialog box appears. The selection options return to the default
setting of selecting only objects that are closest to the front of the screen.
3-92
A tutorial: Using additional techniques to create and analyze a model
a. Toggle on the buttons labeled U1, U2, and U3 to constrain the end of the hinge in the 1-,
2-, and 3-directions. You do not need to constrain the rotational degrees of freedom of the
hinge because solid elements (which have only translational degrees of freedom) will be
used to mesh the hinge.
· Like interactions, boundary conditions are step-dependent and can change from one step to
another.
· The boundary condition editor allows you to constrain selected degrees of freedom.
d. Click Continue.
3. In the viewport, select the rigid body reference point on the pin as the region where the boundary
3-93
A tutorial: Using additional techniques to create and analyze a model
closest object tool . Now ABAQUS/CAE cannot choose between the vertex and the
reference point, and you must click the Next and Previous buttons until ABAQUS/CAE selects
the reference point. The text string in the viewport displays Highlighting Pin-1 Ref
Point when you have selected the reference point.
5. Click mouse button 2 to indicate that you have finished selecting regions.
The Edit Boundary Condition dialog box appears.
a. Toggle on all the buttons to constrain all the degrees of freedom of the pin.
b. Click OK.
The new boundary condition appears in the Boundary Condition Manager.
· To constrain a rigid surface, you must apply constraints to the reference point.
1. In the Boundary Condition Manager, click the cell labeled Propagated that lies in the row
labeled NoSlip and in the column labeled Load, as shown in Figure 3-44.
3-94
A tutorial: Using additional techniques to create and analyze a model
Figure 3-44 Select boundary conditions to edit in the Boundary Condition Manager.
2. On the right side of the manager, click Edit to indicate that you want to edit the NoSlip boundary
condition in the Load step.
The Edit Boundary Condition dialog box appears, and ABAQUS/CAE displays a set of arrows
on the model indicating where the boundary condition is applied and which degrees of freedom are
constrained.
3. In the editor, toggle off the buttons labeled U1 and UR2 so that the pin is allowed to translate in
the 1-direction and rotate about the 2-axis. Click OK to close the dialog box.
In the Boundary Condition Manager, the status of the NoSlip boundary condition in the Load
step changes to Modified.
· You can use the Boundary Condition Manager to delete or modify a boundary condition within a
step.
2. Apply the boundary condition to the vertex selected from the solid hinge piece, as shown in Figure
3-45.
Figure 3-45 Apply a boundary condition to a vertex of the solid hinge piece.
3-95
A tutorial: Using additional techniques to create and analyze a model
4. In the Load step, modify the boundary condition so that the hinge is unconstrained in the
1-direction.
5. When you have finished creating boundary conditions, click Dismiss to close the Boundary
Condition Manager.
e. Click Continue.
3. In the viewport, select the face at the end of the solid hinge piece as the surface to which the load
will be applied, as shown by the gridded surface in Figure 3-46.
3-96
A tutorial: Using additional techniques to create and analyze a model
4. Click mouse button 2 to indicate that you have finished selecting regions.
The Edit Load dialog box appears.
5. In the dialog box, enter a magnitude of -1.E6 for the load, and click OK.
Arrows appear on the nodes of the face indicating the applied load.
· You can create different types of loads, and you can select the region of the model to which a load
is applied.
· Making sure the assembly can be meshed and creating additional partitions where necessary.
· Orange indicates that a region cannot be meshed using the default element shape assignment
(hexahedral) and must be partitioned further. (Alternatively, you can mesh any model by assigning
tetrahedral elements to the model and using the free meshing technique.)
3-97
A tutorial: Using additional techniques to create and analyze a model
For the tutorial ABAQUS/CAE indicates that the hinges need to be partitioned to be meshed using
hexahedral-shaped elements. Specifically, areas surrounding the hole in the flange and the lubrication
hole must be partitioned. The partitioned hinges are shown in Figure 3-47.
Use the following techniques to help you select faces and vertices during the partitioning process:
· Use a combination of the view manipulation tools, the display option tools in the toolbar, and the
tools in the Views toolbox to resize and reposition the model as necessary. (The Views toolbox
· From the prompt area, click the selection options tool and toggle off the closest object tool
to cycle through the possible selections using the Next and Previous buttons in the prompt
area.
· You will probably find the magnification tool and the rotation tool especially useful.
· When necessary, click the Iso tool in the Views toolbox to return the model to its original size and
position in the viewport.
1. Use the Assembly Display Options dialog box to display all three part instances.
2. In the Module list located under the toolbar, click Mesh to enter the Mesh module.
3-98
A tutorial: Using additional techniques to create and analyze a model
ABAQUS/CAE displays the two hinge pieces in orange, which indicates that they need to be
partitioned to be meshed using hexahedral elements, as shown in Figure 3-48.
ABAQUS/CAE also displays the pin in orange because it is an analytical rigid surface and cannot
be meshed.
3. From the main menu bar, select Tools->Partition to partition the two hinge pieces.
ABAQUS/CAE displays the Create Partition dialog box.
4. From the Create Partition dialog box, choose the Cell partition type. Select the Extend face
method, and click Apply.
5. Select the solid hinge piece as the cell to partition and click Done to indicate you have finished
selecting cells.
6. Select the face to extend, as shown by the gridded face in Figure 3-49. Toggle off the closest
Figure 3-49 Select a face of the solid hinge piece to extend to create a partition.
3-99
A tutorial: Using additional techniques to create and analyze a model
Tip: If the partition is not located correctly, select Feature->Delete from the main menu bar
and select the partition to delete.
ABAQUS/CAE colors the cube portion of the solid hinge piece green to indicate that it can be
meshed using the structured meshing technique; it colors the flange of the solid hinge piece yellow
to indicate that it can be meshed using a swept mesh.
8. Use a similar method to that described in the previous steps to create a partition between the cube
and the flange of the other hinge piece.
Again the cube turns green to indicate that it can be meshed using structured meshing, but the
flange containing the lubrication hole remains orange, indicating that you need to perform
additional partitioning to mesh this flange.
· ABAQUS/CAE color codes the model to indicate how a region will be meshed. Green indicates
that a region can be meshed with structured methods, yellow indicates that a region can be meshed
with sweep methods, and orange indicates that a region cannot be meshed.
· You can partition the parts of your model into regions to create a model that can be meshed.
3-100
A tutorial: Using additional techniques to create and analyze a model
1. From the Create Partition dialog box, select the Define cutting plane method, and click Apply.
2. Select the two flanges. Select the first flange and [Shift]+[Click] the second flange to append it to
your selection. Click Done to indicate you have finished selecting cells.
ABAQUS/CAE provides three methods for specifying the cutting plane:
· Select a point and a normal. The cutting plane passes through the selected point, normal to the
selected edge.
· Select three non-colinear points. The cutting plane passes through each point.
· Select an edge and a point along the edge. The cutting plane passes through the selected point,
normal to the selected edge.
The cutting plane need not be defined in the cell being partitioned. The plane extends infinitely
and partitions the selected cell anywhere there is an intersection.
4. Select three points that cut the flanges in half with a vertical partition, as shown in Figure 3-52.
3-101
A tutorial: Using additional techniques to create and analyze a model
Tip: You may find it easier to select the desired points if you magnify, rotate, and pan the
model to obtain a more convenient view.
6. You have now partitioned each of the flanges into two regions; you need to create a partition that
cuts the resulting four regions in half horizontally, as shown in Figure 3-53. Use the Define
cutting plane method to create the desired partitions. Remember that since the cutting plane
extends infinitely, points that define it need not be on the cells being partitioned; for example, you
can select midpoints of edges around the cube to define the cutting plane through the four regions.
The plane extends infinitely and partitions the selected regions anywhere an intersection occurs.
7. ABAQUS/CAE colors the region containing the lubrication hole orange to indicate that it still
cannot be meshed. Use the Define cutting plane method to partition the four regions in the flange
containing the lubrication hole, as shown in Figure 3-54.
3-102
A tutorial: Using additional techniques to create and analyze a model
The coloring of the model indicates that it can now be meshed completely.
8. From the prompt area, click Done to indicate that you have finished partitioning cells.
· You use the Partition toolset to divide the model into regions that ABAQUS/CAE can mesh.
3-103
A tutorial: Using additional techniques to create and analyze a model
1. You cannot mesh an analytical rigid surface. As a result you cannot apply mesh controls to an
analytical rigid surface; neither can you seed it or assign an element type to it. To simplify the
meshing procedure, you should use the Assembly Display Options to display only the the two
hinge pieces. The pin, which is an analytical rigid surface, will not be selected in the following
steps.
3. Drag a square around the model to select the two hinge parts and click Done to indicate your
selection is complete.
The two hinge pieces appear red in the viewport to indicate that you have selected them, and
ABAQUS/CAE displays the Mesh Controls dialog box.
4. In the dialog box, accept Hex as the default Element Shape selection.
6. Click OK to assign the mesh controls and to close the dialog box.
· You can select the meshing techniques that ABAQUS/CAE will apply to your model.
2. Select the two hinge pieces using the same technique described in the mesh controls procedure,
and click Done to indicate your selection is complete.
ABAQUS/CAE displays the Element Type dialog box.
6. Click the Hex tab, and select Reduced Integration as the Element Controls method if it is not
3-104
A tutorial: Using additional techniques to create and analyze a model
already selected.
A description of the default element type, C3D8R, appears at the bottom of the dialog box.
ABAQUS/CAE will now associate C3D8R elements with the elements in the mesh.
7. Click OK to assign the element type and to close the dialog box.
· ABAQUS/CAE assigns a default ABAQUS element type to the model; you can accept the default
element type or choose to assign other element types to different regions of the model.
2. Select the two hinge pieces using the same technique described in the mesh controls procedure,
and click Done to indicate your selection is complete.
3. In the text box in the prompt area, type an approximate global element size of 0.004, and press
[Enter].
Seeds appear on all the edges. You are now ready to mesh the assembly.
· Seeds represent the approximate locations of nodes and indicate the target density of the mesh that
you would like to generate.
3-105
A tutorial: Using additional techniques to create and analyze a model
2. Select the two hinge pieces using the same techniques described in the mesh controls procedure,
and click Done to indicate your selection is complete.
The cursor changes to an hourglass while ABAQUS/CAE meshes the assembly. The final mesh is
illustrated in Figure 3-56.
1. In the Module list located under the toolbar, click Job to enter the Job module.
The cursor changes to an hourglass while the Job module loads.
2. From the main menu bar, select Job->Create to create the job.
The Create Job dialog box appears.
3-106
A tutorial: Using additional techniques to create and analyze a model
6. From the buttons on the right edge of the Job Manager, click Submit to submit your job for
analysis.
The job can take anywhere from 10 to 60 minutes, depending on your system.
7. Click the Monitor button on the right edge of the Job Manager to monitor the analysis as it
runs.
A dialog box appears with the name of your job in the title bar and a status chart for the analysis.
Messages appear in the lower panel of the dialog box as the job progresses. Click the Errors and
Warnings tabs to check for problems in the analysis.
Once the analysis is underway, an X-Y plot of the values of the degree of freedom that you selected
to monitor earlier in the tutorial appears in a separate window in the viewport. (You may need to
scroll to the right to see it.) You can follow the progression of the node's displacement over time in
the 1-direction as the analysis runs.
8. When the job completes successfully, the text in the Status field of the Job Manager changes to
Completed. You are now ready to view the results of the analysis with the Visualization module.
From the buttons on the right edge of the Job Manager, click Results.
ABAQUS/CAE loads the Visualization module, opens the output database created by the job, and
displays a plot of the model.
Note: You can also enter the Visualization module by clicking Visualization in the Module list located under the toolbar.
However, in this case ABAQUS/CAE requires you to open the output database explicitly using the File menu.
· When you create and name a job, ABAQUS/CAE uses the same name for the input file it
generates. Consequently, all files associated with the analysis (for example, the output database,
the message file, and the status file) use the same name.
· Use the Job Manager to monitor the status of your job. You can also view the progression of a
degree of freedom over the course of an analysis that you have chosen to monitor before
submitting the job.
3-107
A tutorial: Using additional techniques to create and analyze a model
In this section you will display a contour plot of the model and adjust the deformation scale factor.
To display a contour plot of the model:
By default, all surfaces with no results (in this case, the pin) are displayed in white.
The deformation is exaggerated because of the default deformation scale factor that
ABAQUS/CAE selects.
b. In the ODB Item options list, select Surfaces. In the Selection Method options list,
select All surfaces.
c. At the bottom of the Create Display Group dialog box, click Remove.
The white surfaces disappear from the view.
b. From the Contour Plot Options dialog box that appears, click the Shape tab.
d. In the Value text field, type a value of 100, and click OK.
ABAQUS/CAE displays the contour plot with a deformation scale factor of 100, as shown
in Figure 3-57.
Figure 3-57 Contour plot of von Mises stress with a reduced deformation scale factor.
3-108
A tutorial: Using additional techniques to create and analyze a model
4. Use the view manipulation tools to examine the deformed model. Note where the pin appears to be
exerting the most pressure against the insides of the flanges. Also note how the two flanges have
twisted away from each other.
5. By default, the contour plot displays the von Mises stresses in the model. You can view other
variables by selecting Result->Field Output.
The Field Output dialog box appears.
6. Click the Primary Variable tab of the Field Output dialog box, and select S11 from the list of
Component options. Click Apply to see a contour plot of the stresses in the 1-direction.
7. From the Invariant option list, select Max. Principal, and click Apply to see the maximum
principal stresses on the model.
8. Select any other variables of interest from the Field Output dialog box.
9. From the Invariant option list, select Mises and click Apply to display the von Mises stresses
again.
· When you first open an output database, ABAQUS/CAE displays a fast plot of the model. You
cannot customize a fast plot.
· For all other plot modes--undeformed, deformed, contour, symbol--you use the associated options
to control the appearance of the plot in each mode. In general, changing an option in one mode
does not affect the appearance of the plot in the other modes.
3-109
A tutorial: Using additional techniques to create and analyze a model
2. In the ODB Item options list, select Elements. In the Selection Method options list, accept the
default selection of Element sets.
The right side of the dialog box displays all the element sets in the model. ABAQUS/CAE creates
a number of sets automatically. Some of the sets are named according to the following convention:
ASSEMBLY__part instance name_label__setname. Part instance name consists of the name you
gave to the part when you created it, plus an instance number that ABAQUS/CAE assigns. Label is
G for geometry set, E for elements picked in the viewport, or N for nodes picked in the viewport.
Finally, setname is either a name assigned to the set by ABAQUS/CAE or a set name given by
you. The sets created by ABAQUS/CAE are geometry sets.
3. Select the element set created by ABAQUS/CAE for the Hinge-hole-1 part.
4. At the bottom of the Create Display Group dialog box, click Replace.
The contour plot of the entire model is replaced by a plot of only the selected hinge piece, as
shown in Figure 3-58.
Figure 3-58 Use display groups to view a contour plot of the von Mises stress in the hinge piece
with the lubrication hole.
5. Use the view manipulation tools to view the hinge at different angles. You can now see results for
surfaces on the hinge that were hidden by the solid hinge.
6. Click the Primary Variable tab of the Field Output dialog box, select CPRESS for the
INSIDE-H/PIN contact pair in the Output Variable options list, and click Apply. You may need
to widen the Name column to see the entire contact pair name. Do this by dragging the dividing
line between the Name and Description column headings.
ABAQUS/CAE displays a contour plot of the contact pressures in the flange hole.
3-110
A tutorial: Using additional techniques to create and analyze a model
· A display group can be an element set, a node set, or a list of nodes or elements.
To learn more about the capabilities of the Visualization module, see the third tutorial, Chapter 4, "A
tutorial: Viewing the output from your analysis."
For more information about using the Visualization module, click any of the following items:
· For a more in-depth tutorial of the capabilities of the Chapter 4, "A tutorial: Viewing the output
from your analysis"
You have now completed the second tutorial and learned how to:
· use position constraints to assemble a model composed of more than one part;
3-111
A tutorial: Viewing the output from your analysis
4.1 Overview
During the tutorial you will display the output from Case 2 of the example problem, ``Indentation of an
elastomeric foam specimen with a hemispherical punch,'' Section 1.1.4 of the ABAQUS Example
Problems Manual. The problem studies the behavior of a heavy metal punch impacting a soft
elastomeric foam block; the resulting deformation and strain are shown in Figure 4-1.
The problem is modeled in two dimensions and is divided into three steps:
1. The punch initially rests on the surface of the foam block and compresses the block under its own
weight. The gravity loading is ramped up over two seconds; but the analysis continues for a total
of five seconds, allowing the foam to relax fully. The analysis uses the *VISCO option to model
the response of the foam block during the step.
2. The punch is forced down with an impulsive load that varies according to a half sine wave over a
period of one second. The response of the foam block is modeled using the *DYNAMIC option.
3. The impulsive load is removed, and the punch is allowed to move freely while the foam expands
and contracts. The viscoelastic foam damps out the vibrations, and the step runs for 10 seconds
while the model returns to steady state. As with the second step, the response of the foam block is
modeled using the *DYNAMIC option.
4-112
A tutorial: Viewing the output from your analysis
Field Output
The Field Output portion of the output database contains variables that should be output
relatively infrequently during the analysis; in this case, after every 10 increments and after the
last increment of a step. Typically, you select output for your entire model or a large region of
your model, and ABAQUS writes every component at the selected frequency. Only the
selected variables are written to the output database.
The following input file fragment shows the options that control the field output variables in
the elastomeric block example:
*OUTPUT, FIELD, FREQUENCY=10
*CONTACT OUTPUT, SLAVE=ASURF, MASTER=BSURF,
VARIABLE=PRESELECT
*NODE OUTPUT
U,
*ELEMENT OUTPUT, ELSET=FOAM
S,E
ABAQUS/Standard writes the following variables to the Field Output portion of the output
database after every 10 increments and at the end of each step:
4-113
A tutorial: Viewing the output from your analysis
· the logarithmic strain components of every integration point in the foam block (by default,
the logarithmic strain is written to the output database when the user requests strain for a
geometrically nonlinear analysis);
· the default contact output variables (clearance, pressure, shear stress, and tangential
motion) resulting from the contact between the punch and the foam block.
History Output
The History Output portion of the output database contains variables that may be output
relatively frequently during the analysis, as often as every increment. To avoid generating
large amounts of data, you typically select output from a small area of your model, such as a
single element or a small region. In addition, you must select the individual components of the
variables that are written to the output database. History output is typically used for generating
X-Y data plots.
The following input file fragment shows the options that control the history output variables in
the elastomeric block example:
*OUTPUT, HISTORY, FREQUENCY=1
*NODE OUTPUT, NSET=N9999
U2, V2, A2
*ELEMENT OUTPUT, ELSET=CORNER
MISES, E22, S22
ABAQUS/Standard writes the following variables from the punch's rigid body reference node
(contained in node set N9999) to the history portion of the output database after every
increment:
In addition, after every increment ABAQUS/Standard writes the following variables from the
element at the corner of the block to the history portion of the output database:
The stress and strain variables are written for all the integration points in the element.
4-114
A tutorial: Viewing the output from your analysis
1. If you have not done so already, start ABAQUS/CAE by typing abaqus cae at the operating
system prompt.
2. From the Start Session dialog box that appears, select Open Database .
The Open Database dialog box appears.
3. From the File type list at the top of the Open Database dialog box, select Output Database
(*.odb).
The remainder of the dialog box changes to reflect the fact that you are now interested in files with
the extension .odb only.
4. If you are following this tutorial online, resize your windows so that you can follow this tutorial
and see the ABAQUS/CAE main window. For more information, see ``Starting ABAQUS/CAE,''
Section 5.1.1.
5. In the Selection field at the bottom of the Open Database dialog box, delete the text and type
abaqus_dir/cae/Tutorial/viewer_tutorial.odb, where abaqus_dir is the name of
the directory in which ABAQUS/CAE is installed. To determine the location of abaqus_dir at
your site, type abaqus whereami at an operating system prompt.
Note: On Windows NT systems the path to the output database is
abaqus_dir\cae\Tutorial\viewer_tutorial.odb.
6. Click OK.
ABAQUS/CAE starts the Visualization module and displays a fast plot of the model, as shown in
Figure 4-2. A fast plot is a basic representation of your undeformed model and is an indication that
you have opened the desired output database. The fast plot mode does not display results and
cannot be customized.
4-115
A tutorial: Viewing the output from your analysis
Important: Do not confuse this fast plot with the undeformed shape plot. While the fast plot
displays the undeformed model, you must display the undeformed plot to customize the
appearance of the model; for example, to display element and node numbering. The fast plot
simply indicates that you have opened the desired output database.
The title block at the bottom of the viewport indicates the following:
· The description of the model (from the first line of the *HEADING option in the input file).
· The name of the output database (from the name of the analysis job).
The state block at the bottom of the viewport indicates the following:
The orientation triad indicates the orientation of the model in the global coordinate system.
· ABAQUS/CAE loads the Visualization module automatically when you open an output database.
· The model is initially displayed using a fast mode. You cannot change the appearance of the model
in fast mode.
· The title block displays information about the analysis that generated the output database.
· The state block contains information about the step and increment being displayed.
4-116
A tutorial: Viewing the output from your analysis
toolbox. Click the undeformed plot tool in the Visualization module toolbox to select
the undeformed mode.
The Visualization module enters the undeformed plot mode and displays the undeformed model at
the end of the analysis-- Step 3 and Step Time = 10.00 in this example. The plot mode and
a set of buttons also appear in the prompt area, as shown in Figure 4-3.
In the elastomeric foam block example ABAQUS/Standard wrote the data to the field output
portion of the output database after every 10 increments and after the last increment of a step. Each
increment written to the output database is called a frame.
In this example the undeformed model does not change between frames, but in some simulations
the model changes during the analysis; for example, if rigid surfaces are introduced.
2. Use the pan tool, which is one of several view manipulation tools available on the toolbar, to move
the model above the state and title blocks as follows.
a. From the toolbar, click the pan tool to enter pan mode.
b. To move the model away from the state and title blocks, click in the viewport and drag the
4-117
A tutorial: Viewing the output from your analysis
cursor upward.
The model moves along the same path as the cursor.
3. From the prompt area, click the button on the far left to move to the first frame of the current step.
ABAQUS/CAE displays the undeformed model at the beginning of the third step--Step 3,
Increment 0, and Step Time = 0.000. This is the state of the model at the beginning of
the step.
The first frame and last frame buttons take you directly to the first or last frame of the current step
but do not allow you to move between steps. The next frame and previous frame buttons in the
prompt area allow you to move between each frame of the analysis and can cross step boundaries
as needed.
· To perform many Visualization module functions, you can use either a menu item or a tool in the
toolbox.
· You can use the buttons in the prompt area to display the state of the model in each frame of the
analysis.
· You can use the view manipulation tools in the toolbar to change the view of the model to a more
convenient one. Use mouse button 2 to stop any view manipulation.
4-118
A tutorial: Viewing the output from your analysis
· Click the Plot Mode Options button at the far right of the prompt area.
· Click mouse button 3 in the viewport, and select Plot Mode Options from the menu that
appears.
2. Click the Basic tab in the Undeformed Plot Options dialog box if it is not already selected.
Choose the Filled render style and Exterior visible edges, and click Apply.
ABAQUS/CAE displays a filled view of the model. Because the model is a two-dimensional
model, it displays all edges--the perimeter edges and the edges of each element--as shown in
Figure 4-4.
Figure 4-4 Undeformed plot with filled view and exterior edges visible.
For clarity, most of the figures in this tutorial do not include the title block, state block, and
orientation triad. In general, the figures illustrate the effect on the model of changing the plot mode
and customizing the plot. You can toggle off and customize the title block, state block, and
orientation triad by selecting View->Viewport Annotations from the main menu bar.
3. By default, ABAQUS/CAE fills the model in green and displays element labels using cyan text.
You will change the color of the element labels from cyan to red and display them. From the
Undeformed Plot Options dialog box, click the Labels tab and do the following:
4-119
A tutorial: Viewing the output from your analysis
b. Click Apply.
ABAQUS/CAE displays the element numbering using cyan text.
d. Click OK.
The color of the element labels changes from cyan to red, and the Undeformed Plot
Options dialog box closes.
· The Visualization module has different plot modes. Each plot mode has options associated with it
that you can use to control the appearance of the model in that mode. Undeformed plot
customization options apply only to undeformed plots.
· You use the viewport annotation options to customize the appearance of items that appear in all
plots, such as the title block, the state block, and the orientation triad.
· When you click Apply in an options dialog box, ABAQUS/CAE applies the change and keeps the
dialog box displayed. When you click OK, ABAQUS/CAE applies the change and closes the
dialog box.
· Customization options apply only to the current viewport and are not saved between sessions.
4-120
A tutorial: Viewing the output from your analysis
Tip: You can also plot the deformed model using the tool in the Visualization module
toolbox.
ABAQUS/CAE displays the deformed model in the same increment and step that it last displayed
the undeformed model. The state block indicates the default deformed variable being plotted ( U)
and the deformation scale factor (1.00). ABAQUS/CAE selects a default deformation scale factor
of 1.00 for large-displacement analyses. If the deformation is small (for example, for a perturbation
analysis), ABAQUS/CAE increases the scale factor. Conversely, if the deformation is large,
ABAQUS/CAE decreases the scale factor to fit the viewport optimally.
2. The buttons in the prompt area allow you to move between frames of the analysis, but you can also
move directly to a selected step and increment using the following technique:
c. The Frame Selector also displays the step time associated with an increment. Use the
Frame Selector dialog box to display the deformed model approximately halfway
through the second step.
3. Use a combination of the buttons in the prompt area and the Frame Selector dialog box to view
the deformed plot in different frames and in different steps.
4. Display the deformed model after the last increment of the third step (Step 3 and Step Time
= 10.00), as shown in Figure 4-5.
Figure 4-5 Deformed plot of the model after the last increment of the third step.
4-121
A tutorial: Viewing the output from your analysis
· When you display a deformed plot, ABAQUS/CAE selects a default variable to display from the
field output portion of the output database.
· You can use the Frame Selector dialog box to select the step and frame to display.
2. Click the Basic tab if it is not already selected, and do the following:
4. Click OK to apply your changes and to close the Deformed Plot Options dialog box.
ABAQUS/CAE displays the customized deformed plot overlaid with the undeformed plot.
5. To turn off the fill color and the element numbering of the undeformed plot, select
Options->Undeformed from the main menu bar.
4-122
A tutorial: Viewing the output from your analysis
6. From the buttons at the bottom of the Undeformed Plot Options dialog box, click Defaults.
Click OK to apply the default undeformed plot options and to close the Undeformed Plot
Options dialog box.
· When you set options in one plot mode, they are not carried over to other plot modes.
· You can use the Defaults button to restore the default plot options in each plot mode.
4-123
A tutorial: Viewing the output from your analysis
Tip: You can also display a contour plot using the tool in the Visualization module
toolbox.
The state block indicates that the variable plotted is S, MISES, the default variable chosen by
ABAQUS/CAE. ABAQUS/CAE displays the results at the same step and frame that you used to
display the deformed shape plot.
2. Use a combination of the buttons in the prompt area and the Frame Selector dialog box to view
the contour plot in different frames and in different steps.
Note: The legend changes as you move between frames. ABAQUS/CAE updates the maximum and minimum values and
computes the contour intervals in every frame.
· In all plot modes, including contour, ABAQUS/CAE selects a default variable to display.
a. From the Output Variable field, select LE (logarithmic strain components at integration
points).
4-124
A tutorial: Viewing the output from your analysis
4. Click OK to select LE22 as the primary variable and to close the Field Output dialog box.
The contour plot in the current viewport changes to a plot of LE22, as shown in Figure 4-7.
Figure 4-7 Contour plot of the model after the last increment of the third step.
· In all plot modes you use the Field Output dialog box to select the variable to display.
· You can display a contour plot of any variable stored in the field output portion of the output
database.
1. Display the contour plot at the end of the last increment of the second step (Step 2 and Step
Time = 1.000).
4-125
A tutorial: Viewing the output from your analysis
3. Click the Basic tab if it is not already selected, and do the following:
a. In the Max field, toggle the Specify button and type a maximum contour limit of 0.1.
b. In the Min field, toggle the Specify button and type a minimum of -0.75.
Although you selected 16 contour intervals, the plot legend displays 17 intervals. ABAQUS/CAE
adds intervals to indicate any values that are greater than the maximum contour limit or less than
the minimum contour limit and displays these values in light gray and dark gray, respectively. In
this example, areas undergoing compressive strains greater than 0.75 are shown in dark gray. The
minimum strain in the model is shown at the bottom of the contour legend. You might use either of
these colors to indicate elements that fall outside the design range for the selected variable.
6. Under the Limits tab, examine the Min and Max Auto-compute options.
The minimum and maximum values of strain for the contour plot are shown next to the two
4-126
A tutorial: Viewing the output from your analysis
Auto-compute options.
· You use the contour plot options to customize the appearance of a contour plot.
· By default, ABAQUS/CAE uses light and dark gray contour bands to indicate values that are
outside the limits shown in the legend.
The animation uses the plot options from the relevant mode--deformed, contour, or symbol. In
addition, you can control the following:
For the elastomeric foam example you will display a time history animation of a contour plot. The
animated contour plot displays the variable you selected from the Field Output dialog box (E22). In
addition, it uses the same options that you selected for the contour plot; for example, the contour
intervals and element edge display.
To animate the contour plot:
4-127
A tutorial: Viewing the output from your analysis
animation. After the last increment of the last step, the animation restarts at the beginning of the
analysis (Step 1, Increment 0, and Step Time = 0.00).
ABAQUS/CAE also displays the movie player controls on the left side of the prompt area:
You use these controls to start, stop, and step through the animation.
2. In the prompt area, click the stop button to stop the animation.
The animation stops at the current image.
3. In the prompt area, click the play button to continue the animation.
The animation resumes.
4. From the main menu bar, select Options->Animation to view the animation options.
ABAQUS/CAE displays the Animation Options dialog box.
5. Click the Player tab if it is not already selected, and do the following:
a. Choose Swing .
c. Click OK.
Because you increased the frame rate, ABAQUS/CAE steps through the animation at a faster rate.
Because you chose Swing , when the animation reaches the end of the analysis, it steps backward
through each frame instead of jumping back to the beginning of the analysis.
6. You can also customize the contour plot while the animation is running.
c. Click OK to apply your change and to close the Contour Plot Options dialog box.
7. When you have finished viewing the animation, click the stop button to stop the movie.
· You can display a time history animation from the data in an output database, or you can generate
a scale factor animation based on a single increment of the results.
4-128
A tutorial: Viewing the output from your analysis
· You can animate a deformed, contour, or symbol plot; the animation uses the respective plot
options to control the appearance of the model. You can customize these plots while the animation
is running.
· You can use the buttons in the prompt area to start, stop, and step through the animation.
· You can use the Animation Options to control the speed and behavior of the animation.
3. From the output variable Name list, select U (spatial displacement at nodes).
From the Invariant field, select Magnitude if it is not already selected. This selection indicates
that you want to plot the magnitudes of the displacement vectors.
4. Click OK to select the field output variable and to close the Field Output dialog box.
The contour plot in the current viewport displays the magnitude of the displacement vector but
retains your customized settings for the contour limits. You can click the Defaults button in the
Contour Plot Options dialog box to restore the default options.
Tip: You can also display a symbol plot using the tool in the Visualization module toolbox.
4-129
A tutorial: Viewing the output from your analysis
The arrows represent the total displacement at each node. The length of the arrow represents the
magnitude of the displacement, and the direction of the arrow represents the direction of the
displacement.
If your symbol plot is different from Figure 4-9, you may not have selected the correct output
variable. On the Primary Variable page in the Field Output dialog box, select U and Magnitude
and remember to click OK.
· You can display symbol plots of any selected field output variable, including both nodal and
element quantities.
· A symbol plot shows the magnitude and direction of a particular vector or tensor variable at a
specified step and frame. By default, symbol plots display the magnitudes for vector variables or
all principal components for tensor variables.
· The length of the arrow represents the magnitude of the variable; the direction of the arrow
represents the direction in which the variable is acting.
2. In the Symbol Plot Options dialog box, click the Color & Style tab if it is not already selected,
and do the following:
4-130
A tutorial: Viewing the output from your analysis
3. Click OK to apply your changes and to close the Symbol Plot Options dialog box.
The customized symbol plot appears, as shown in Figure 4-10.
Tip: You can also display a material orientation plot using the tool in the Visualization module toolbox.
4-131
A tutorial: Viewing the output from your analysis
Material orientation triads at element integration points indicate the material directions of each
element in the model.
· A material orientation plot shows the material directions of elements in your model at a specified
step and frame of your analysis. Material orientations are displayed on an element-by-element
basis at the material integration points, with no averaging across elements.
2. Click the Color & Style tab if it is not already selected, and do the following:
3. Click OK to apply your changes and to close the Material Orientation Plot Options dialog box.
The customized material orientation plot appears, as shown in Figure 4-12.
4-132
A tutorial: Viewing the output from your analysis
2. The Output Variables field contains a list of all the variables in the history portion of the output
database. Select the vertical motion of the rigid body reference node Spatial
displacement: U2 at Node 9999 in NSET N9999 if it is not already selected.
3. The ODB History Output dialog box allows you to select where in the history data the X-Y plot
should begin and end; in most cases the X-axis is assumed to be time. To create an X-Y plot using
data in all three steps, do the following:
a. Enlarge the dialog box so that all steps in the Steps field are visible.
4-133
A tutorial: Viewing the output from your analysis
You can also choose the frequency at which to read the frames. For the tutorial you can accept the
default setting of Frames: Read all.
4. From the buttons across the bottom of the ODB History Output dialog box, click Plot.
ABAQUS/CAE displays an X-Y plot of displacement versus time, as shown in Figure 4-13.
Default options selected by ABAQUS/CAE include default ranges for the X- and Y-axes, axis
titles, major and minor tick marks, the color of the line, and a legend.
The legend labels the X-Y plot U2 N: 9999 NSET N9999 . This is a default name provided by
ABAQUS/CAE.
· You can display an X-Y plot of any variable stored in the output database. In most cases the X-axis
is assumed to be time.
· You can select the step from which to start and end an X-Y plot, and you can choose the frequency
at which ABAQUS/CAE reads the frames from history data in the output database.
4-134
A tutorial: Viewing the output from your analysis
3. Specify that the X-axis should extend from 20 (the X-axis maximum) to 0 (the X-axis minimum)
and that the Y-axis should extend from 0 (the Y-axis maximum) to -200 (the Y-axis minimum).
4. Click Apply to view the customized X-Y plot and to keep the XY Plot Options dialog box active.
The axes of the X-Y plot change.
5. From the options in the XY Plot Options dialog box, do the following. (Click Apply as you work
to check the effect of each setting.)
· Select Blue horizontal and vertical major grid lines. The line style should be solid.
· Request that major tick marks appear on the X-axis at four-second increments.
· Request a decimal format with zero decimal places for the Y-axis labels.
· Request a minor tick mark every second along the X-axis and every 10 mm along the Y-axis.
6. From the XY Plot Options dialog box, click OK to view the customized X-Y plot, as shown in
Figure 4-14.
4-135
A tutorial: Viewing the output from your analysis
7. You will now display a second X-Y plot in a new viewport. To create a new viewport, do the
following:
b. Position the cursor at one corner of the desired location for the new viewport.
c. Drag the cursor across the drawing area to the opposite corner of the new viewport. The
exact size and position of the new viewport is not critical because you can move and
resize it later.
The new viewport appears. The same X-Y plot that you had in the first viewport appears in
the new viewport.
The red border around the new viewport indicates that it is the current viewport; all work takes
place in the current viewport. For more information, see ``What is a viewport?,'' Section 7.1.1.
8. Create a similar X-Y plot of vertical velocity ( V2) versus time. You cannot select velocity during
the first step because the first step was not a dynamic step; ABAQUS/Standard computed velocity
and acceleration only during the second and third steps. Use the same X-axis range as before, and
use a Y-axis range from 1000 to -1000. Label the Y-axis Velocity V2. The finished plot is
shown in Figure 4-15.
4-136
A tutorial: Viewing the output from your analysis
X-column and a Y-column. The Operate on XY Data dialog box allows you to create new X-Y data
objects by performing operations on previously saved X-Y data objects. In this tutorial you will create a
stress versus strain data object by combining a stress versus time data object with a strain versus time
data object. Then, you will plot the stress-strain curve.
4.11.1 Creating the stress versus time and strain versus time
data objects
The first step in creating the stress-strain curve is to create the stress versus time and the strain versus
time data objects from the history output. The data objects will contain data from only the first step of
the analysis, where the punch rests on the surface of the foam block and compresses the block under its
own weight.
To create the X-Y data objects:
3. From the Create XY Data dialog box that appears, select ODB history output if it is not already
selected and click Continue.
The ODB History Output dialog box appears.
5. Use a similar technique to create a data object containing stress data ( S22) from integration point
1 of element 1 during the first step of the analysis. Name this data object Stress.
Now you are ready to combine the two data objects to create a stress versus strain data object.
4-137
A tutorial: Viewing the output from your analysis
· You can create X-Y data objects using history data from selected steps.
2. From the Create XY Data dialog box that appears, select Operate on XY data and click
Continue.
An Operate on XY Data dialog box appears. The dialog box contains the following lists:
· The XY Data field on the left contains a list of existing X-Y data objects.
· The Operators field on the right contains a list of all the possible operations you can perform
on the data objects.
4. In the XY Data field, drag the cursor across both the Strain and the Stress data objects to
select both.
When you release the mouse button, the expression combine("Strain","Stress") appears
in the expression text field. In this expression "Strain" will determine the X-values and
"Stress" will determine the Y-values in the combined plot.
Warning: If you select the data objects individually, you must type the comma in the expression text field.
5. From the buttons along the bottom of the Operate on XY Data dialog box, click Save As.
6. From the Save XYData As dialog box that appears, enter the name Stress/strain and click
OK.
· You can use the Operate on XY Data dialog box to create new X-Y data objects based on
operations on existing data objects.
4-138
A tutorial: Viewing the output from your analysis
You will now use the Stress/strain data object that you just created to plot the stress-strain
curve.
To plot the stress-strain curve:
1. Your plot of stress versus strain will inherit the customized settings from your previous plot. To
restore the default plot options, do the following:
c. Click Apply.
3. To change the axis titles, click the Titles tab from the XY Plot Options dialog box. Type Strain
for the X-axis title and Stress for the Y-axis title.
4. Click OK to see your titles and to close the XY Plot Options dialog box.
The plot of stress versus strain appears, as shown in Figure 4-16.
4-139
A tutorial: Viewing the output from your analysis
1. From the main menu bar, select Tools->Query; select Probe values from the Visualization
Queries portion of the dialog box; and click OK to enter probe mode.
The Probe Values dialog box appears. Because an X-Y plot is in the current viewport, this dialog
box will display X-Y curve data.
2. At the top of the dialog box, toggle on Interpolate between points . This option allows you to
select arbitrary points along the curve.
7. From the Probe Values dialog box, click Cancel to exit probe mode.
A dialog box appears to inform you that the Selected Probe Values table contains data. Click
Yes to indicate that it is OK to continue; the data in the table will be deleted.
· You can use the Query toolset to probe a model or X-Y plot. You can write the values you obtain
to a file.
4-140
A tutorial: Viewing the output from your analysis
3. Name the path Displacement. Accept the default selection of Node list as the path type, and
click Continue.
The Edit Node List Path dialog box appears.
4. In the Node Labels table, enter 1:601:100; and click OK. (This input specifies a range of nodes
from 1 to 601 at increments of 100.)
Alternatively, you can pick the nodes for the node list directly from the viewport by clicking
Select in the Edit Node List Path dialog box.
2. In the Create XY Data dialog box that appears, select Path; and click Continue.
The Create XY Data from Path dialog box appears with the path that you created visible in the
list of available paths. The selected path is also highlighted in the plot in the current viewport.
Note: ABAQUS/CAE warns you that three of the node labels included in the specified range
are not available and will be ignored. Click Dismiss to continue.
Accept the default selections in the X Values portion of the dialog box.
The result that will be plotted is displayed in the Y Values portion of the dialog box. In this case U
is the field output variable that was selected last (when you generated the symbol plot).
3. Click Plot to generate an X-Y plot of U along the path, as shown in Figure 4-17.
Figure 4-17 Path plot of U along the top of the foam block.
4-141
A tutorial: Viewing the output from your analysis
4-142
Interacting with ABAQUS/CAE
0-143
The basics of interacting with ABAQUS/CAE
database
This option specifies the name of the model database file or output database file to open. To
specify a model database file, include either the .cae file extension or no file extension in
your file name. To specify an output database file, include the .odb file extension in your file
1-144
The basics of interacting with ABAQUS/CAE
name.
replay
This option specifies the name of the file from which ABAQUS/CAE commands are to be
replayed. The commands in replay-file will execute immediately upon startup of
ABAQUS/CAE. For more information, see ``Replaying an ABAQUS/CAE session,'' Section
12.4.1.
recover
This option specifies the name of the file from which a model database is to be rebuilt. The
commands in journal-file (model_database_name .jnl) will execute immediately upon
startup of ABAQUS/CAE. For more information, see ``Recreating a saved model database,''
Section 12.4.2, and ``Recreating an unsaved model database,'' Section 12.4.3.
startup
This option specifies the name of the file containing Python configuration commands to be run
at application startup. Commands in this file are run after any configuration commands that
have been set in the environment file.
noenvstartup
This option specifies that all configuration commands in the environment files should not be
run at application startup. This option can be used in conjunction with the startup command
to suppress all configuration commands except for those in the startup file.
ABAQUS/CAE begins. If you do not include the database, replay, or recover options, the Start
Session dialog box appears. Choose one of the following session startup options:
Open Database
Use this option to open a previously saved analysis or output database (equivalent to choosing
File->Open from the main menu bar).
Run Script
Use this option to run a file containing ABAQUS/CAE commands (equivalent to choosing
File->Run Script from the main menu bar). For more information, see ``Creating and running
your own scripts,'' Section 12.4.4.
Start Tutorial
Use this option to begin an introductory tutorial from the online documentation (equivalent to
choosing Help->Getting Started from the main menu bar). The ABAQUS/CAE User's
Manual opens in a separate window.
1-145
The basics of interacting with ABAQUS/CAE
Note: You can disable the Start Session dialog box by including the following line in your
ABAQUS/CAE resource file:
*useStartupDialog: false
For more information on the ABAQUS/CAE resource file, see ``Customizing X resources,''
Section 6.1. If you choose to disable the Start Session dialog box, you must open an existing or a
new model database after you start ABAQUS/CAE by selecting either File->Open or File->New
from the main menu bar.
· ``Understanding the files generated by creating and analyzing a model,'' Section 12.3
1-146
The basics of interacting with ABAQUS/CAE
Title bar
The title bar indicates the version of ABAQUS/CAE you are running and the name of the
current model database.
Menu bar
The menu bar contains all the available menus; the menus give access to all the functionality
in the product. Different menus appear in the menu bar depending on which module you
selected from the context bar. For more information, see ``Components of the main menu bar,''
Section 5.2.2.
1-147
The basics of interacting with ABAQUS/CAE
Toolbar
The toolbar provides quick access to items that are also available in the menus. For more
information, see ``Components of the toolbar,'' Section 5.2.3.
Context bar
ABAQUS/CAE is divided into a set of modules, where each module allows you to work on
one aspect of your model; the Module list in the context bar allows you to move between these
modules. Other items in the context bar are a function of the module you are working in; for
example, the context bar allows you to retrieve an existing part while creating the geometry of
the model. For more information, see ``The context bar,'' Section 5.2.4.
Toolbox area
When you enter a module, the toolbox area displays tools in the toolbox that are appropriate
for that module. The toolbox allows quick access to many of the module functions that are
also available from the menu bar. For more information, see ``Understanding and using
toolboxes,'' Section 6.4.
Viewport
Viewports are windows on the canvas in which ABAQUS/CAE displays your model. For more
information, see Chapter 7, "Managing objects on the canvas."
Prompt area
The prompt area displays instructions for you to follow during a procedure; for example, it
asks you to select the geometry as you create a set. For more information, see ``Using the
prompt area during procedures,'' Section 6.2.
Message area
ABAQUS/CAE prints status information and warnings in the message area. To resize the
message area, drag the small square at its upper right corner; to see information that has
scrolled out of the message area, use the scroll bar on the right side.
1-148
The basics of interacting with ABAQUS/CAE
When you start a session, the menus listed below appear on the main menu bar. ABAQUS/CAE
displays additional menu options and provides access to toolsets depending on the current module in
use.
File
The items in the File menu allow you to create, open, and save model databases; open and
close output databases; import and export files; run scripts; manage macros; print canvas
objects; and exit ABAQUS/CAE. For more information, see ``Using the File menu,'' Section
12.5.
Model
The items in the Model menu allow you to open, copy, rename, and delete the models in the
current model database. For more information, see ``Managing models,'' Section 12.7.
Canvas
The items in the Canvas menu allow you to create or manipulate viewports and annotations
and to open the canvas toolbox. All the tools that are available directly from the menu are also
available from the canvas toolbox. For more information, see Chapter 7, "Managing objects on
the canvas."
View
The items in the View menu allow you to manipulate views, customize certain aspects of the
appearance of your model, and control display performance. Some of the operations available
in the view manipulation menu are also available in the toolbar. For more information, see any
of the following:
Help
The items in the Help menu allow you to request context-sensitive help and to search or
browse the documentation. For more information, see ``Getting help,'' Section 5.6.
1-149
The basics of interacting with ABAQUS/CAE
in the toolbar are shortcuts to functions that are also available from the main menu bar. The toolbar is
shown in the following figure:
To obtain a short description of a tool, place the cursor over that tool for a moment; a small box
containing a description, or "tooltip," will appear. The tools are divided into the following groups:
The database manipulation tools allow you to create and manipulate model databases and to
print viewports and annotations. For more information, see Part III, "Working with
ABAQUS/CAE model databases, models, and files," and Chapter 11, "Printing canvas
objects."
View manipulation
The view manipulation tools allow you to specify different views of the model. For example,
you can pan, rotate, or zoom the model using these tools. For more information, see Chapter 8,
"Manipulating the view and controlling perspective ."
The view and display option tools allow you to customize the appearance of your model. For
example, you can specify whether wireframe, hidden line, or shaded render style will be used
and whether perspective will be applied. For more information, see ``Choosing a render style,''
Section 37.2.1, and ``Controlling perspective,'' Section 8.3.
Query
Use the query tool to obtain information about the geometry and features of your model.
For more information, see Chapter 44, "The Query toolset."
Help
Use the context-sensitive help tool to display detailed information about any tool, menu,
dialog box, or option in ABAQUS/CAE. For more information, see ``Getting help,'' Section
5.6.
1-150
The basics of interacting with ABAQUS/CAE
The items displayed in the context bar always refer to the current viewport, which is indicated by a red
border. For example, if you have different parts displayed in different viewports, the context bar
indicates the name of the part displayed in the current viewport.
1-151
The basics of interacting with ABAQUS/CAE
The viewport title and the border around the viewport are called the viewport decorations. For more
information, see ``Showing and hiding viewport decorations,'' Section 7.3.9.
The legend, state block, title block, and view orientation triad are called the viewport annotations. The
view orientation triad is a set of three perpendicular axes that indicate the orientation of the model
currently being displayed. For more information, see ``Customizing the view triad,'' Section 8.2. The
legend, state block, and title block identify results you display using the Visualization module. For
more information, see Chapter 38, "Customizing viewport annotations."
1-152
The basics of interacting with ABAQUS/CAE
allows you to select any module at any time, regardless of the state of your model.
The following list of the modules available within ABAQUS/CAE briefly describes the modeling tasks
you can perform in each module. The order of the modules in the list corresponds to the order of the
modules in the context bar's Module list:
Part
Create individual parts by sketching or importing their geometry. For more information, see
Chapter 14, "The Part module."
Property
Create section and material definitions and assign them to regions of parts. For more
information, see Chapter 15, "The Property module."
Assembly
Create and assemble part instances. For more information, see Chapter 16, "The Assembly
module."
Step
Create and configure the analysis steps and associated output requests. For more information,
see Chapter 17, "The Step module."
Interaction
Specify the interactions, such as contact, between regions of a model. For more information,
see Chapter 18, "The Interaction module."
Load/BC/IC
Specify loads, boundary conditions, and initial conditions. For more information, see Chapter
19, "The Load/BC/IC module."
Mesh
Create a finite element mesh. For more information, see Chapter 20, "The Mesh module."
Job
Submit a job for analysis and monitor its progress. For more information, see Chapter 21, "The
Job module."
Visualization
View analysis results. For more information, see Part V, "Viewing results."
Sketch
Create two-dimensional sketches. For more information, see Chapter 22, "The Sketch
module."
The contents of the main window change as you move between modules. Selecting a module from the
1-153
The basics of interacting with ABAQUS/CAE
Module list on the context bar causes the context bar, module toolbox, and menu bar to change to
reflect the functionality of the current module.
When you select a module from the Module list on the context bar, ABAQUS/CAE associates the
current viewport with the module you select. You can have multiple viewports, and different viewports
can be associated with different modules. As you select a viewport and make it current, the module
associated with the viewport becomes the current module. For more information on moving between
viewports, see ``Making the selected viewport current,'' Section 7.3.6.
· The Amplitude toolset allows you to define arbitrary time or frequency variations of load,
displacement, and other prescribed variables. For more information, see Chapter 40, "The
Amplitude toolset."
· The Color Code toolset allows you to customize the edge and fill color of individual elements and
surfaces. For more information, see ``Coloring individual elements and surfaces,'' Section 37.4.
· The Datum toolset allows you to create datum points, axes, planes, and coordinate systems for a
variety of modeling tasks. For more information, see Chapter 41, "The Datum toolset."
· The Display Group toolset allows you to selectively plot one or more output database items. For
more information, see Chapter 36, "Displaying a subset of your model."
· The Field Output toolset allows you to perform operations on the field output available in an
output database. For more information, see ``Creating new field output,'' Section 24.5.
· The Partition toolset allows you to divide a part or assembly into regions. For example, you can
partition a face and apply a pressure load to the resulting region. You can also use partitions to
refine your mesh by creating additional edges and vertices. For more information, see Chapter 43,
"The Partition toolset."
· The Set toolset and the Surface toolset allow you to define sets and surfaces from regions of a
model. Sets and surfaces are named regions of a model to which you can assign attributes and
apply prescribed conditions. For example, when you create a load, you must apply the load to a
region of your model. You can specify the load by picking a region from the viewport or by
selecting a set. Likewise, you can create two surfaces from faces of your model and then select
those surfaces when you define an interaction. For more information, see Chapter 45, "The Set and
1-154
The basics of interacting with ABAQUS/CAE
Surface toolsets."
· The XY Data toolset allows you to create and operate on X-Y data objects. For more information,
see Chapter 30, "X-Y plotting."
Sometimes the objects that you create with a toolset in one module are useful in other modules. For
example, you can use the Set toolset to create sets in the Assembly module and then apply boundary
conditions to those sets in the Load/BC/IC module. Most of the toolsets include manager menus and
manager dialog boxes that allow you to edit, copy, rename, and delete the objects you create with the
toolset.
Mouse button 1
You use mouse button 1 to select objects in the viewport, to expand pull-down menus, and to
select items from menus. The instructions ``click,'' ``select,'' and ``drag'' in the documentation
refer to mouse button 1.
Mouse button 2
Clicking mouse button 2 in the viewport signifies that you have finished the current task. For
example:
· Selecting entities from the model: when you create a node set, you select the nodes to
include in the set. Clicking mouse button 2 indicates that your selection is complete and
you are ready to create the set.
· Using a tool: click mouse button 2 to indicate that you have finished with a view
manipulation tool.
In addition, clicking mouse button 2 in the viewport is equivalent to clicking the highlighted
button in the prompt area. For example, if you tried to select nodes from your model and
ABAQUS/CAE displayed the following prompt, clicking mouse button 2 would have the same
effect as clicking OK:
Mouse button 3
Pressing and holding mouse button 3 in the viewport exposes a popup menu that contains
shortcuts to any of the buttons on the prompt area. For example, when you press mouse button
3 in a viewport that contains a contour plot, the Visualization module displays the following
menu:
1-155
The basics of interacting with ABAQUS/CAE
The mouse button 3 shortcut is available only when ABAQUS/CAE displays buttons in the
prompt area.
You can use the help tool in the toolbar to display detailed help on any icon, menu, or dialog box
that you use in ABAQUS/CAE. When you click the help tool and then click an item in the
ABAQUS/CAE window, a help window appears containing the section from the online documentation
that is relevant to that item.
In most cases the section from the online documentation that appears is equally applicable to both
ABAQUS/Standard and ABAQUS/Explicit analyses. However, in some cases you must specify the
product of interest (either ABAQUS/Standard or ABAQUS/Explicit) so that documentation specific to
the analysis type can be displayed. In these cases a dialog box appears in which you can specify the
product of your choice.
To display help on an item in the main window or in a dialog box:
1. From the right end of the toolbar, click the help tool to start the context-sensitive help server.
Tip: You can also start the server by selecting Help->On Context from the main menu bar.
2. Position the cursor over the item that you need help with and click mouse button 1. Then, if
necessary, select the product (ABAQUS/Standard or ABAQUS/Explicit) for which you want to
display help.
After a short delay a help window appears that contains the appropriate online documentation and
hyperlinks to associated topics. The window is like any other window on your workstation in that
1-156
The basics of interacting with ABAQUS/CAE
it can be resized both horizontally and vertically and moved to suit your needs.
Note: Subsequent context-sensitive help requests are addressed much more quickly because the help server is already running.
3. If a dialog box appears in which you must specify the product of your choice, do the following:
b. Toggle on Do not display this dialog box for subsequent help requests if you want
all help that is displayed during the current session to apply only to the product that you
just selected.
c. Click OK to close the dialog box and to display the help window.
After a short delay the help window appears.
Alternatively, you can use the [F1] key to display help on a particular item. In most cases you can gain
access to context-sensitive help by using the Help menu, the help toolbar icon, or the [F1] key.
However, you must use [F1] if you are seeking information about menu items and certain kinds of
dialog boxes.
To display help using the [F1] key:
1. Click the feature in the ABAQUS/CAE window that you want help with. If the feature is part of a
menu, do not release the mouse button.
2. Press [F1]. Then, if necessary, select the product (ABAQUS/Standard or ABAQUS/Explicit) for
which you want to display help.
A window appears that contains the appropriate online documentation and links to associated
topics. If you selected a menu item without releasing the mouse button, that menu disappears.
Note: ABAQUS/CAE also provides brief ``tooltips'' that describe the function of tools in
toolboxes and in the toolbar. To see a ``tooltip,'' position the cursor over a tool and leave it
stationary for a short time.
1. From the main menu bar, select Help->Search & Browse Manuals .
ABAQUS/CAE displays the library window with a list of all of the manuals in the online
documentation collection.
1-157
The basics of interacting with ABAQUS/CAE
2. In the Book Titles column on the right side of the window, double-click the manual title of
interest.
Tip: You can also open the manual by first selecting it on the right side of the window and
then selecting File->Open Book from the library window menu bar.
ABAQUS/CAE displays a two-panel window containing the manual that you selected. The right
panel contains the contents of the manual, and the left panel contains the table of contents (TOC).
For example, the book window for UNIX systems appears in Figure 5-3. (The book window for
Windows NT systems has the same layout but a slightly different appearance.)
· To scroll so that you can view additional manual content or additional TOC entries, use the
scroll bars to the right of the content and TOC panels.
· To jump directly to a section whose title is displayed in the TOC, click that title.
· To search for a word or phrase, enter it in the Find text box at the bottom of the book window.
The search engine searches for the precise word or phrase you type; for example, searching for
the word ``element'' yields different results than searching for the word ``elements.'' Use the
1-158
The basics of interacting with ABAQUS/CAE
[*] character as a wildcard; for example, searching for ``element*'' will find occurrences of the
words ``element,'' ``elements,'' ``elemental,'' and ``elementary.'' Searches are not case sensitive.
On Module
Select Help->On Module to display the ABAQUS/CAE User's Manual opened to the
beginning of the chapter that describes the current module. If you have not yet entered a
module, the manual will be opened to a description of the module concept. In either case, you
are then free to read additional information as needed and to conduct text searches through the
entire manual.
Getting Started
Select Help->Getting Started to display the ABAQUS/CAE User's Manual opened to a
section that provides basic information on how to work in the ABAQUS/CAE window. This
section also contains helpful tutorials. You are free to read additional information as needed
and to conduct text searches through the entire manual.
On Help
Select Help->On Help to display the ABAQUS/CAE User's Manual opened to the section that
describes how to use the help system. You are also free to read additional information as
needed and to conduct text searches through the entire manual.
Release Notes
Select Help->Release Notes to display the ABAQUS Release Notes. Release notes detail
new features of the software and provide a list of updates and enhancements.
On Version
Select Help->On Version to determine which version of ABAQUS/CAE you are currently
using.
· The ABAQUS/CAE module or toolset that contains the functionality associated with each
keyword.
· Help->Keyword Browser
1-159
The basics of interacting with ABAQUS/CAE
For example, you could use the keyword browser to verify that the *ELASTIC option allows you to
specify elastic material properties and that the Property module is the ABAQUS/CAE module
associated with this keyword.
The keyword browser also contains hyperlinks to relevant sections in the online documentation. You
can click a particular keyword in the table to display detailed information concerning the function of
that keyword. You can also click the name of a module or toolset in the table to view related
documentation in the ABAQUS/CAE User's Manual.
To display the keyword browser:
2. In the Keyword column, click the keyword of interest to view online documentation describing
that keyword.
3. In the Module or Toolset column, click the module or toolset name of interest to view online
documentation concerning that module or toolset.
1-160
Understanding ABAQUS/CAE windows, dialog boxes, and toolboxes
On UNIX systems
· You can place a customized resource file for all users on a given machine in
/usr/lib/X11/app-defaults/Abaqus
You can place a customized resource file for an individual user either in their home directory
or in the directory to which the environment variable XAPPLRESDIR points. A resource file
for an individual user will take precedence over a machine-wide file.
On Windows NT systems
2-161
Understanding ABAQUS/CAE windows, dialog boxes, and toolboxes
or in any directory to which the environment variable XAPPLRESDIR points. If resource files
are present in both locations, the one pointed to by XAPPLRESDIR will take precedence.
To determine the location of abaqus_dir at your site, type abaqus whereami at an operating
system prompt.
Any specifications you enter in your customized resource file override the corresponding default
specifications. For example, the resource specifications for background and foreground window color
are shown below:
?*background : #adadad
?*foreground : Black
These lines specify that the background color of all windows and dialog boxes associated with
ABAQUS/CAE be gray (the shade of gray indicated by the rgb code #adadad) and that objects in the
foreground, such as text, appear in black. In general, rgb color specifications are more precise than
color name specifications, which are system-dependent. If you decide that you want the foreground
color to be blue instead of black, you can include the following in your Abaqus resource file:
?*foreground : Blue
You can also use your resource file to specify keyboard shortcuts for certain functions. For example,
the following lines indicate that a keyboard shortcut exists for the Open item in the File menu:
*menuBar*fileMenu.openBtn.accelerator : Ctrl<key>O
*menuBar*fileMenu.openBtn.acceleratorText : Ctrl+O
The first line above specifies that pressing [Ctrl]+O produces the same result as selecting Open from
the File menu. The second line specifies that the text Ctrl+O appears in the File menu next to the
Open menu item to remind you of this keyboard shortcut.
Refer to the sample resource file to see a list of many of the resources that you can customize. The file
contains comments that help you find the resources of interest.
2-162
Understanding ABAQUS/CAE windows, dialog boxes, and toolboxes
· ``Following instructions and entering data in the prompt area, '' Section 6.2.2
3. Press [Enter].
ABAQUS/CAE displays each step of a procedure in the prompt area near the bottom of the main
window so that you do not need to remember all the steps and their order.
The button marked X in the above figure is the Cancel button; click this button to cancel the entire
procedure at any time. The arrow to the left of the Cancel button is the Previous Step button; click it to
abort the current step of the procedure and return to the previous one. (The Previous Step button
appears dimmed during the first step of any procedure.) If you prefer, you can place the cursor over the
canvas and press mouse button 3; then select Previous Step or Cancel Procedure from the menu that
appears.
A Stop button appears in the prompt area during certain time-consuming operations, such as part
healing or meshing. You can click Stop to interrupt and cancel the operation.
Many procedures require textual or numeric data; for example, when creating a fillet using the Sketch
module, you must first specify the fillet radius. When textual or numeric data are required,
ABAQUS/CAE displays a text field in the prompt area for you to fill in; usually the text box will
already contain a default value, as shown here:
2-163
Understanding ABAQUS/CAE windows, dialog boxes, and toolboxes
Position your cursor over the canvas, and enter data into the text field as follows:
· To replace the default value, simply begin typing; you need not click the text field before typing.
The default value disappears as soon as you begin to type.
· To change a portion of the default value, first click the text field; then use the [Delete] key and the
other keys on your keyboard to change the value.
Some procedures require you to choose from a number of options. For example, the Datum toolset may
ask you to choose a coordinate system type. Such options are represented by buttons in the prompt
area, as shown here:
If you click More Options, an editor appears that provides you with more options for defining the
object than are available in the prompt area. For example, when you edit a translational velocity initial
condition, a Velocity (V1,V2,V3) text field appears in the prompt area (see the figure above); in this
text field you can enter the three components of the initial velocity. Alternatively, if you click More
Options, the following editor appears:
2-164
Understanding ABAQUS/CAE windows, dialog boxes, and toolboxes
As in the prompt area, this editor allows you to enter the initial translational velocity in the 1-, 2-, and
3-directions. In addition, the editor allows you to edit the region to which the initial condition applies.
When you define this type of initial condition in the prompt area instead of using the editor, you must
accept the currently defined region.
· To commit the contents of any text field that appears in the prompt area, click mouse button 2.
· To accept any default option depicted by a highlighted button in the prompt area, click mouse
button 2.
· To reveal a menu containing options identical to those in the prompt area, press and hold mouse
button 3. For example, given the following prompt:
Items above the horizontal line correspond to the option buttons on the right side of the prompt
area, while items below the line correspond to the Previous Step and Cancel buttons.
To select an item from the menu, hold down mouse button 3 while dragging the cursor to the
2-165
Understanding ABAQUS/CAE windows, dialog boxes, and toolboxes
· ``Using dimmed dialog box and toolbox components, '' Section 6.3.2
· ``Understanding the OK, Apply, Defaults, Continue, Cancel, and Dismiss buttons, '' Section 6.3.3
Text fields are available whenever you need to name an object, such as a part, material, or set.
Object names must adhere to the following rules:
· The name can include spaces and most punctuation marks and special characters.
2-166
Understanding ABAQUS/CAE windows, dialog boxes, and toolboxes
However, when you are naming a model or job you cannot use the following characters:
$&*~!()[]{}|;'`",.?/\. Similarly, when you are specifying a name that will be
external to ABAQUS/CAE, such as a file name, you should avoid any character that may have
a reserved meaning on your platform.
ABAQUS/CAE retains the case of any text you enter. For example, if you name a material
STEEL in the Property module, the material will appear as STEEL in the material manager
and the section editor. However, within ABAQUS/CAE, ABAQUS/Standard, and
ABAQUS/Explicit all text is case insensitive; you cannot use case to distinguish between
objects such as parts and materials. If you create a material called STEEL in the Property
module, you cannot create a second material called Steel.
Numeric fields are text fields having two opposing arrows directly to the right of the text area.
You can enter a numeric value into the text field, or you can use the arrows to cycle up and
down through a list of fixed values.
Combo boxes
Combo boxes are text fields having an arrow directly to the right of the text area. If you click
this arrow, a list of the possible choices that you can enter in the field appears. For example, if
you click the arrow to the right of the Color text field shown below, a list of all the possible
colors you can enter in the field appears, and you can select the color of your choice from the
list.
Radio buttons
Radio buttons present a mutually exclusive choice. When an option is controlled by radio
buttons, you can choose only one of the buttons at a time.
Check boxes
You can toggle a check box to turn a particular option off or on.
For example, the visibility of the triad in the current viewport depends on the status of the
Show triad check box. If the box is toggled on, as shown below, the triad appears in the
viewport.
2-167
Understanding ABAQUS/CAE windows, dialog boxes, and toolboxes
If the box is toggled off, as shown below, the triad does not appear in the viewport.
In some cases the option controlled by a check box can apply to more than one object. For
example, a single Show line check box on the XY Curve Options dialog box individually
controls the display of all X-Y curve lines in an X-Y plot. If you have toggled Show line on for
some curves and off for others, that check box appears half-highlighted, as shown below.
Menu buttons
When you click a menu button, a menu appears from which you can select the item of your
choice. The current selection appears on the button. The Labels menu button is shown below:
Scroll bars
Scroll bars appear in lists whose contents are too big to display; they allow you to scroll
through the visible contents of the list as well as any contents that are hidden. Scrolling is
often necessary when the numerous items must be listed, as shown below.
Sliders
Sliders allow you to set the value of an option that has a continuous range of possible values.
An example of a slider is shown below.
2-168
Understanding ABAQUS/CAE windows, dialog boxes, and toolboxes
object is unavailable, it appears dimmed in the dialog box. Items are usually dimmed as a result of
some other setting in the dialog box. For example, if Show triad is not selected, the triad
customization options below it are not available and appear dimmed, as shown below.
Context-sensitive help is available even for dimmed options, although tooltips are not.
When you are finished working with a dialog box, you can specify how to proceed by using different
action buttons. For example, if you enter data in a dialog box, you can save the data and apply them by
clicking OK. If the dialog box is part of an intermediate step of a procedure, you can click Continue to
move on to the next step.
The following action buttons can appear in a dialog box:
OK
Click OK to commit the current contents of a dialog box and to close the dialog box.
Apply
When you click Apply, any changes you have made in the dialog box take effect, but the
dialog box remains displayed. This button is useful if you make changes in a dialog box and
would like to see the effects of these changes before closing the dialog box.
Defaults
If you want to revert back to the predefined default values after entering data or specifying
preferences in a dialog box, you can click Defaults. This button affects only the information
entered in the dialog box. It does not apply your changes or close the dialog box; therefore, to
see the effect of reverting to the default values, you must click Apply or OK.
2-169
Understanding ABAQUS/CAE windows, dialog boxes, and toolboxes
Cancel
Click Cancel to close a dialog box without applying any of the changes that you made. If the
dialog box appears in the middle of a procedure, clicking Cancel also cancels the procedure.
Continue
Dialog boxes that appear in the middle of a procedure contain Continue buttons. When you
click Continue, you indicate that you have finished entering data in the current dialog box and
would like to move on to the next step of the procedure. Continue causes the dialog box to be
closed and all data in it to be saved unless you click Cancel at some point later in the
procedure.
Dismiss
Dismiss buttons appear in dialog boxes that contain data that you cannot modify. For
example, some managers contain lists of objects that exist but no fields in which you can enter
data or specify preferences. Dismiss buttons also appear in message dialog boxes. When you
click Dismiss, the dialog box closes.
To close a toolbox or a dialog box that does not have a Cancel or Dismiss button, double-click the
close button in the upper left corner of the toolbox or dialog box.
Note: On Windows NT systems you click the close button in the upper right corner of the toolbox
or dialog box.
2-170
Understanding ABAQUS/CAE windows, dialog boxes, and toolboxes
If you click the Color & Style tab, the dialog box containing the color and edge attributes options
comes forward, obscuring the other four dialog boxes, as shown in Figure 6-2.
In addition, separated dialog boxes can exist within a single dialog box. In this case the tabs of the
separated dialog boxes are aligned vertically but work the same way as tabs aligned horizontally. In
Figure 6-3 the Other dialog box contains two dialog boxes separated by tabs: Scaling and
2-171
Understanding ABAQUS/CAE windows, dialog boxes, and toolboxes
Translucency.
The action buttons in a dialog box apply to the whole set of dialog boxes, not just the one you are
currently viewing. If you click Cancel, all of the unapplied changes you have made in the set of dialog
boxes are canceled, not just those in the current dialog box. Likewise, clicking OK saves all changes
that you have made in any of the dialog boxes.
Data tables are composed of input boxes, or cells, organized into rows and columns. You can type data
2-172
Understanding ABAQUS/CAE windows, dialog boxes, and toolboxes
into a table using the keyboard or you can read data in from a file.
The following list describes techniques for entering and modifying tabular data:
Entering data
Click any cell, and type the required data. You can press [Enter] to commit the data in a
particular cell.
ABAQUS/CAE does not allow you to enter character data in tables requiring numeric data; the
program beeps if you attempt to enter character data in a numeric field. (The letter E that
denotes scientific notation, as in 12. E6, is an exception to this rule.)
· Select Add Row Before to add a blank row above the current row.
· Select Add Row After to add a blank row below the current row.
Alternatively, you can add a blank row to the end of the table by clicking the cell in the last
row and in the last column of the table and then pressing [Enter].
· In the File text field, enter the name of the file to read.
· Specify the row number and column number of the target cell in the Start reading values
into table row and Start reading values into table column fields, respectively. (By
default, ABAQUS sets these fields to the cell your cursor was over when you clicked
mouse button 3.)
Click OK. ABAQUS reads data values from the file into the table according to your
specifications.
2-173
Understanding ABAQUS/CAE windows, dialog boxes, and toolboxes
move from cell to cell. Use [Tab] to move to the right and [Shift]+[Tab] to move to the left;
use the up and down arrows to move up and down. You can also simply click the cell of
interest.
Changing data
If a cell already contains data, clicking the cell allows you to use the [Backspace] key and the
other keys on your keyboard to modify the data in that cell. Use the [Escape] key to cancel any
changes you have made and return the contents of the cell to their original state.
After clicking the cell once, you can double-click to highlight the data; as soon as you begin
typing, the highlighted contents of the cell disappear and are replaced by whatever you type.
You can use the [Backspace] or [Delete] keys to delete highlighted data in a cell.
Sorting data
Some data tables offer a sorting feature. (To determine if sorting is available for a particular
table, hold the cursor over the table; then click mouse button 3. If it is available, Sort is listed
in the menu that appears.)
To sort table data, click mouse button 3 while holding the cursor over the table; then click
Sort. The Sort Table dialog box appears. In this dialog box, choose the following:
Click OK or Apply. ABAQUS sorts all rows according to data values in the specified column.
2-174
Understanding ABAQUS/CAE windows, dialog boxes, and toolboxes
You can also resize the last column in some tables by horizontally enlarging the dialog box
that contains the table.
Viewing data that extend beyond the edge of the dialog box
Use the horizontal and vertical scroll bars to view portions of a table that are outside the
boundaries of the dialog box. In some cases scroll bars may not be available; instead, increase
the size of the dialog box to display more data.
· Specify the column number containing the X-values and the column number containing
the Y-values.
· Click OK. ABAQUS reads the data values from the table into the X-Y data.
ABAQUS/CAE retains saved X-Y data only for the duration of the session.
· From the main menu bar, select Tools->XY Data->Plot, and select the X-Y data from the
pull-right menu.
2-175
Understanding ABAQUS/CAE windows, dialog boxes, and toolboxes
The Select Font dialog box allows you to specify and preview the following:
The available options vary depending on which fonts are installed on your system.
To customize viewport fonts:
1. Display the Select Font dialog box for the text that you want to customize. For more information,
see the following sections:
2-176
Understanding ABAQUS/CAE windows, dialog boxes, and toolboxes
· ``Editing canvas annotation color, line, and font attributes, '' Section 7.4.6
3. Click OK to accept your changes and to close the Select Font dialog box.
· ``Editing canvas annotation color, line, and font attributes, '' Section 7.4.6
2-177
Understanding ABAQUS/CAE windows, dialog boxes, and toolboxes
Similar file selection dialog boxes appear when you perform other File menu functions, such as
importing a part or printing to a file.
Use the following techniques to select the file of your choice:
2-178
Understanding ABAQUS/CAE windows, dialog boxes, and toolboxes
Selecting a file
To select and open a file, double-click the file name of interest from the list in the Files field.
Alternatively, you can enter the entire directory path and file name of interest directly in the
Selection field and then click OK.
Some functions allow you to operate on more than one item. For example, if you wanted to delete the
first two data objects in the manager shown in Figure 6-7, you could select them both and then click
Delete.
To select a single item, you need only click that item in the dialog box. To select multiple items, you
can use the following techniques:
2-179
Understanding ABAQUS/CAE windows, dialog boxes, and toolboxes
Another way to select consecutive items is to click the first item of interest and then
[Shift]+Click the last item of interest. All items between the first and the last are selected
automatically.
Canceling a selection
You can [Ctrl]+Click previously selected items to remove them from your selection. For
example, if you [Ctrl]+Click Strain in the list shown in Figure 6-9, that data object is no
longer selected, as shown in Figure 6-10.
2-180
Understanding ABAQUS/CAE windows, dialog boxes, and toolboxes
Certain functions in a dialog box may become unavailable when you select multiple items. For
example, the Edit, Copy, and Rename functions in the Data Manager shown in Figure 6-10 are valid
only for individual data objects. When you select multiple data objects, these three functions become
unavailable.
Context-sensitive help
Press [F1] to display context-sensitive help concerning the currently selected object in the
ABAQUS/CAE main window or dialog box. For more information on using [F1] for
context-sensitive help, see ``Displaying context-sensitive help,'' Section 5.6.1.
Menus
On UNIX systems you can display a particular menu by pressing the [Alt] key in combination
with the underlined character in that menu's name. For example, the letter C is underlined in
the Canvas menu in the main menu bar:
Therefore, you can type [Alt]+C to display the Canvas menu. The function of the [Alt] key on
Windows NT systems depends on your Exceed configuration settings.
You can also press F10 to select the menu bar and then use the arrow keys to select different
menus. When you have selected the menu of interest, press either [Enter], [Space], or the
down arrow key to display the contents of the menu. Click F10 again to deactivate the menu
bar.
Menu items
Once the menu is displayed, you can select a particular menu item by pressing the underlined
character in that menu item's name. For example, the letter T is underlined in Toolbox in the
Canvas menu:
2-181
Understanding ABAQUS/CAE windows, dialog boxes, and toolboxes
Therefore, you can type [Alt]+C to display the Canvas menu and then T to select Toolbox.
2-182
Understanding ABAQUS/CAE windows, dialog boxes, and toolboxes
All module toolboxes are available immediately to the left of the drawing area as soon as you enter the
module. The canvas and view manipulation toolboxes behave differently; they appear in separate
dialog boxes, and you must select the appropriate menu items to display them: Canvas->Toolbox and
View->Views Toolbox , respectively.
In all cases the tools available from a toolbox are also available from the main menu bar. Toolboxes
are convenient when you are performing many related operations in sequence, whereas menus are more
convenient when you are performing only isolated operations. For example, the canvas toolbox is
useful if you are intricately annotating several viewports; conversely, selecting Canvas->Create
Viewport from the main menu may be more convenient than using the toolbox icon if you are creating
only a single viewport.
To obtain a short description of a tool, place the cursor over that tool for a moment; a small box
containing a description, or ``tooltip,'' will appear. Tooltips are not available for icons that appear
dimmed; to get information on those icons, use context-sensitive help instead.
2-183
Understanding ABAQUS/CAE windows, dialog boxes, and toolboxes
1. Click and hold any icon that includes a triangle in its lower right corner.
Icons for all the tools that are closely related to the original icon appear. For example, Figure 6-12
shows the top portion of the Sketcher toolbox with all of the icons revealed that are used for
creating lines.
Figure 6-12 Sketcher toolbox with all line creation icons displayed.
2. Drag the cursor to the desired icon, and release the mouse button.
The selected icon replaces the icon that was visible originally, and you can begin using the
corresponding tool immediately.
2-184
Understanding ABAQUS/CAE windows, dialog boxes, and toolboxes
The list box on the left shows all the materials that you have defined within the context of the current
model. You use the buttons on the right to create new material definitions and to edit, copy, rename,
and delete existing material definitions. The Dismiss button is used to close the manager dialog box.
Often, the manager provides more information about an object than just its name; for example, in the
Job module, the Job Manager provides information about currently executing jobs and provides
buttons that allow you to write input files, submit jobs, monitor the analysis, or view output files for a
given job. The Job Manager is shown in Figure 6-14.
2-185
Understanding ABAQUS/CAE windows, dialog boxes, and toolboxes
Every task you can perform with a manager can also be performed using the pull-down menus
available from the main menu bar; for example, Figure 6-15 shows the menu items that correspond to
the Job Manager. After you select a management operation from the main menu bar, the procedure is
exactly the same as if you had clicked the corresponding button inside the manager dialog box.
The decision whether to use menus or dialog boxes is yours. In general, menus are more convenient if
you are performing isolated operations; the advantages of manager dialog boxes become apparent
when you are performing several operations in sequence, when you need to browse through a long list
of objects, or when you need quick access to the additional information that is displayed by some
managers.
2-186
Understanding ABAQUS/CAE windows, dialog boxes, and toolboxes
· Load Manager
· Interaction Manager
This manager displays an alphabetical list of existing loads along the left side of the dialog box. The
2-187
Understanding ABAQUS/CAE windows, dialog boxes, and toolboxes
names of all the steps in the analysis appear along the top of the dialog box in the order of execution.
The table formed by these two lists displays the status of each load in each step. (For information on
creating and deleting steps, see Chapter 17, "The Step module.")
If you click one of the cells in the table, that cell becomes highlighted, and the following information
related to the cell appears in the legend at the bottom of the manager:
· The type of analysis procedure carried out in the step in that column.
You can resize the columns of the table by dragging the dividers between the column headings to the
right or left. You can also increase the size of the dialog box by dragging the sides of the box. If the
analysis includes many steps or many step-dependent objects, increasing the size of the dialog box
allows you to view more rows and columns without having to use the scroll bars.
The five buttons along the right side of the manager allow you to manipulate objects in the steps that
you select. For example, if you click Edit in the Load Manager shown above, an editor appears in
which you could modify the load named Force in Step-1. The other buttons-- Move Left, Move
Right, Activate, and Deactivate--allow you to change the status of an object in a particular step. For
more information, see ``Modifying the history of a step-dependent object,'' Section 6.5.4, ``Changing
the status of an object in a step, '' Section 6.5.8, and ``Editing step-dependent objects,'' Section 6.5.9.
2-188
Understanding ABAQUS/CAE windows, dialog boxes, and toolboxes
The load in this example is created in Step 1; therefore, the status of the load in Step 1 is Created.
Since Step 1 is a general static step, the load's magnitude is ramped up over the course of the step. If
the load continues to be active in Step 2, its status in Step 2 is Propagated and its magnitude
remains constant throughout that step. If you edit the load in Step 3, its status in Step 3 becomes
Modified and its magnitude ramps to the new value over the course of the step. If the modified
version of the load continues to be active in Step 4, its status in Step 4 (as in Step 2) is Propagated
and the value is constant. If you deactivate the load in Step 5, its status in Step 5 is Inactive and its
magnitude ramps down to zero. The load remains inactive in Step 6.
ABAQUS/CAE uses the following general terms, which can apply to any step-dependent object, to
describe the status of step-dependent objects in a particular step:
Created
The object was created and becomes active in this step. The point in the step at which a
prescribed condition becomes active depends on the amplitude variation associated with that
step. For more information, see ``Prescribed conditions'' in ``Procedures: overview,'' Section
6.1.1 of the ABAQUS/Standard User's Manual and the ABAQUS/Explicit User's Manual.
Propagated
The object was created or modified in an earlier step of the analysis and continues to be active
in this step.
Modified
The definition of the object has been modified in this step. Again, the variation of a prescribed
condition over the course of the step depends on the amplitude variation associated with that
step.
Inactive
The object has been deactivated in this step or in a previous step. It will remain deactivated in
all subsequent steps until you reactivate it. You cannot deactivate an object in the step in
which it was created. The point in the step at which a prescribed condition becomes inactive
depends on the amplitude variation associated with that step. For more information, see
``Prescribed conditions'' in ``Procedures: overview,'' Section 6.1.1 of the ABAQUS/Standard
User's Manual and the ABAQUS/Explicit User's Manual.)
2-189
Understanding ABAQUS/CAE windows, dialog boxes, and toolboxes
For information on linear perturbation steps, see ``Linear and nonlinear procedures,'' Section 6.1.2 of
the ABAQUS/Standard User's Manual.
2-190
Understanding ABAQUS/CAE windows, dialog boxes, and toolboxes
Modifying an object
You can modify an object when its status is Propagated; the object's status in that step
changes to Modified.
Deactivating an object
You can deactivate an object when its status is Propagated or Modified; the object's
status in that step and in any following steps changes to Inactive.
Warning: If you deactivate an object in a step in which its status is Modified, the
modifications to the object are lost. If you later reactivate the object in that step, the
original propagated version of the object becomes active in that step and in all
subsequent steps.
Reactivating an object
You can reactivate an object that has Inactive status; however, the Activate button is
available only in the step in which the object is first deactivated (for example, Step 3 in the
following table).
Step 1 Step 2 Step 3 Step 4 Step 5
Load1 Created Propagated Inactive Inactive Inactive
When you reactivate the load in the example above, its status in Step 3 and in all following
steps changes to Propagated.
2-191
Understanding ABAQUS/CAE windows, dialog boxes, and toolboxes
You can deactivate a boundary condition whose status is Propagated from base
state; the boundary condition's status in the linear perturbation step changes to
Deactivated from base state. The status Propagated from base state
cannot be moved to other steps.
For information on linear perturbation steps, see ``Linear and nonlinear procedures,'' Section 6.1.2 of
the ABAQUS/Standard User's Manual.
· Modifications that you make to the object in this step become effective in this step and
propagate through all subsequent steps in which the condition is active unless you modify the
object again in a later step.
· The status of the object remains Created in the selected step and also remains unchanged in
all subsequent steps. For more information, see ``Understanding the status of an object in a
step,'' Section 6.5.3.
· Modifications that you make to the object in this step become effective in this step and
propagate through all subsequent steps in which the condition is active.
· The status of the object becomes (or remains) Modified in this step and remains unchanged
2-192
Understanding ABAQUS/CAE windows, dialog boxes, and toolboxes
in all other steps. (In other words, if the status of the object in the following step was
Propagated before modification, its status in the following step remains Propagated
after modification.) For example, the load applied over a sequence of general static analysis
steps in Figure 6-17 has been modified in Step 3; the modifications remain in effect in Step 4
even though the status in Steps 4 is Propagated. For more information, see ``Understanding
the status of an object in a step, '' Section 6.5.3.
· When you modify the data in a Load/BC/IC module editor, ABAQUS/CAE indicates in the
editor which data have been modified. These indications disappear if you change the data in
the editor back to their original values.
In some cases you cannot edit a particular aspect of an object's definition because it must be consistent
for the analysis to proceed correctly. For example, although you can modify the magnitude of a load in
any analysis step, you cannot modify the region to which the load is applied. The areas in an editor that
specify this kind of restricted data are unavailable in all steps except the one in which the object was
created.
Note: For more information on specific managers and where they are located, see the
documentation for the particular module you are interested in.
Use the buttons in the manager's dialog box to manage the list of objects.
To manage objects:
· To start a manager associated with a module, select Manager from the appropriate menu on
the main menu bar. For example, to start the Section Manager while you are working in the
Property module, select Section->Manager from the main menu bar.
· To start a manager associated with a toolset, select Tools->Toolset->Manager from the main
menu bar. For example, to start the Set Manager, select Tools->Set->Manager from the main
menu bar.
· To start the Model Manager, select Model->Manager from the main menu bar.
The manager appears and displays a list of objects in the current model. The list contains the name
of each object and, in some cases, information about each object. For example, the Part Manager
2-193
Understanding ABAQUS/CAE windows, dialog boxes, and toolboxes
lists the name of each part, its type, and the modeling space in which it was created.
2. To manage an existing object, select the object or objects of interest from the list in the manager an
then click the appropriate button. (For example, to delete an object, select that object's name from
the list and then click Delete.)
In most cases a dialog box appears; for example, when you click Rename, the dialog box asks for
the new name of the selected object.
Tip: You can also use the menus in the main menu bar to manage objects. For more information,
see ``Managing objects using manager menus,'' Section 6.5.7.
· To manage objects associated with a module, select the manager menu items in the appropriate
menu in the main menu bar. For example, to edit a material in the Property module you would
select Material->Edit->material of your choice from the main menu bar.
· To manage objects associated with a toolset, select the appropriate manager menu items in the
Tools menu. For example, to delete a set you would select Tools->Set->Delete->set of your
choice from the main menu bar.
· To manage all the models defined in the current model database, select the manager menu
items in the Model menu in the main menu bar. For example, to copy a model you would
select Model->Copy->model of your choice from the main menu bar.
In most cases a dialog box appears; for example, when you rename an object, a dialog box appears
that asks for the new name of the object.
2-194
Understanding ABAQUS/CAE windows, dialog boxes, and toolboxes
Tip: You can also use manager dialog boxes to manage objects. For more information, see ``What
are step-dependent managers?,'' Section 6.5.2.
Use the buttons that become available to manipulate the status of the object in the step that
you have chosen, as described below.
2-195
Understanding ABAQUS/CAE windows, dialog boxes, and toolboxes
For example, the Created status of Pressure in Step-3 is selected in the history shown
above. If you clicked Move Left, the history would change as shown below:
If you clicked Move Right, the history would change as shown below:
The Modified status of Pressure moves to Step-6 (indicating that the modifications to
Pressure become effective in Step-6), and Modified is replaced by Propagated in
Step-5.
2-196
Understanding ABAQUS/CAE windows, dialog boxes, and toolboxes
The Propagated status of Pressure in Step-4 changes to Inactive, and the status in
all subsequent steps becomes Inactive.
Warning: If you deactivate an object in a step in which its status is Modified, the
modifications to the object are lost. If you later reactivate the object in that step, the
original, unmodified version of the object becomes active in that step and in all
subsequent steps.
2-197
Understanding ABAQUS/CAE windows, dialog boxes, and toolboxes
1. In the Step list located under the toolbar, click the step of your choice.
The step that you select becomes the current step.
2. From the main menu bar, select Edit->object of your choice from the appropriate menu. For
example, if you want to edit a load in the Load/BC/IC module, select Load->Edit->load of your
choice.
The region to which the object is applied becomes highlighted in the current viewport.
Either an editor appears or you are prompted to enter data in the prompt area, depending on the
object you are editing. In some cases when you are prompted to enter data in the prompt area, you
can also click More Options to display an editor.
3. In the prompt area or in the editor, modify the object definition as desired.
4. If you are using an editor, click OK to save your changes. If you are using the prompt area, click
the mouse button 2 to save your changes.
1. In the load, boundary condition, or interaction manager, double-click the cell located in the row of
the object that you want to modify and in the column of the step of interest.
Note: Alternatively, you can click the cell located in the row of the object that you want to modify and in the column of the
step of interest and then click Edit.
The current step automatically changes to the analysis step whose column you clicked.
The appropriate editor appears. The region to which the object is applied becomes highlighted in
the current viewport.
2. In the editor, modify the object definition as desired and click OK.
2-198
Understanding ABAQUS/CAE windows, dialog boxes, and toolboxes
· ``Editing the region to which a prescribed condition is applied, '' Section 19.7.19
2-199
Managing objects on the canvas
3-200
Managing objects on the canvas
While the canvas can be thought of as an infinite screen or bulletin board, viewports are simply display
areas posted onto that screen. You can have many viewports on the canvas. A viewport is similar to
other windows on your workstation in that it can be moved, resized, and maximized, and it can overlap
other objects on the canvas. For more information, see ``Working with viewports,'' Section 7.3.
Viewport decorations consist of the border around the viewport and the title bar across the top of the
viewport. You can display or suppress viewport decorations.
The view manipulation tools, such as zoom and rotate, operate on whichever viewport contains the
cursor. Other operations interact with two particular viewports: the selected viewport and the current
viewport.
3-201
Managing objects on the canvas
All viewports are associated with a certain model and module. When you create a new model
or open an existing model or output database, that model becomes associated with whichever
viewport is presently designated as current. You can create different viewports and associate
each one with a different model, so designating each viewport as current results in switching
between the associated models. Similarly, you can work with multiple modules simultaneously
by designating a new viewport as current before starting a different module.
Annotation attributes--color, line style, line thickness, and text font--can be modified from either the
Canvas menu or the Canvas toolbox.
Do not confuse canvas annotations (text and arrows) with viewport annotations. Viewport annotations
include the view orientation triad and, in the Visualization module, the legend, the title block, and the
state block. For more information, see Chapter 38, "Customizing viewport annotations."
3-202
Managing objects on the canvas
· ``Managing canvas objects from the main menu bar,'' Section 7.2.1
· ``Moving canvas objects to the front or the back, '' Section 7.2.3
· Create a viewport
· Edit viewport annotation attributes (triad, legend, title block, and state block)
· Move selected canvas objects to the front or the back of the canvas
3-203
Managing objects on the canvas
3-204
Managing objects on the canvas
· From the main menu bar, select Canvas->Bring to Front to move the selected objects to the
front of the canvas.
· From the main menu bar, select Canvas->Send to Back to send the selected objects to the
back of the canvas.
ABAQUS/CAE moves the selected objects. If you selected more than one object, ABAQUS/CAE
retains the original layering of the selected objects.
Tip: You can also move selected objects to the front and back of the canvas by clicking
The canvas must always contain at least one viewport. As a result, if the canvas contains only one
viewport, you cannot delete the viewport. In addition, if no canvas objects are selected, the Delete
menu item is unavailable.
To delete selected canvas objects:
1. Select the first canvas object you want to delete. For more information, see ``Selecting viewports,''
Section 7.3.2, and ``Selecting canvas annotations,'' Section 7.4.4.
Handles indicate the selected object.
3. From the main menu bar, select Canvas->Delete to delete the selected objects.
ABAQUS/CAE deletes the selected objects from the canvas.
Tip: You can also delete selected canvas objects by clicking in the Canvas toolbox.
3-205
Managing objects on the canvas
In addition, you can delete a viewport by clicking the delete button located in the top right
corner, next to the viewport title. For more information, see ``Deleting a viewport,'' Section
7.3.7.
· ``Showing and hiding the title of selected viewports, '' Section 7.3.8
Tip: You can also create a new viewport by clicking in the Canvas toolbox.
3-206
Managing objects on the canvas
3. Drag the cursor across the drawing area to the opposite corner of the new viewport.
The new viewport appears and becomes the current viewport; a red border indicates the current
viewport.
The exact size and position of the new viewport is not critical because you can move and resize it
later to suit your needs.
5. To unselect all selected viewports, click an unused portion of the drawing area.
Note: Do not confuse the selected viewport with the current viewport. The current viewport is
3-207
Managing objects on the canvas
indicated by a red borderand is associated with a particular model and module . Conversely, the
selected viewport is affected by viewport management and manipulation actions, such as moving,
resizing, or deleting.
2. Place the cursor anywhere on the viewport border except directly on a handle.
3-208
Managing objects on the canvas
2. Resize the viewport by dragging one of its handles; an outline of the viewport shows the new
shape. You can do one of the following:
· Drag one of the four handles located at each corner of the viewport. You can drag these
handles in any direction--vertically, horizontally, or diagonally.
· Drag the handle on either the top or the bottom border of the viewport. You can drag these
handles only vertically.
· Drag the handle on either the left or the right border of the viewport. You can drag these
handles only horizontally.
While you are dragging a handle, the title box of the original viewport displays the distance
between the upper left corner of the new viewport and the upper left corner of the drawing area.
The distance is displayed in units of horizontal ( X) and vertical (Y) screen pixels.
If necessary, use the scroll bars at the edge of the drawing area to reveal the viewport's maximize and
delete buttons.
3-209
Managing objects on the canvas
When you click the maximize button, the viewport changes size and position to fill the drawing area.
In addition, the viewport covers any other viewports that were originally visible in the drawing area.
To maximize the current viewport, you can also click the maximize tool in the Canvas toolbox
or select Canvas->Maximize Current Viewport from the main menu bar.
After you have maximized a viewport to fill the drawing area, you can click this button again to restore
the viewport to its previous size and position. To restore the current viewport, you can also click the
restore tool in the Canvas toolbox or select Canvas->Restore Current Viewport from the
main menu bar.
If the viewport title is hidden, the maximize button is also hidden. However, you can still use the
Canvas menu items or the tools in the toolbox to perform the same functions as the maximize button.
You can also make a selected viewport current by clicking in the Canvas toolbox.
Only one viewport can be the current viewport; if more than one viewport is selected, the Make
Viewport Current menu item is unavailable.
3-210
Managing objects on the canvas
If necessary, use the scroll bars at the edge of the drawing area to reveal the viewport's maximize and
delete buttons.
If it is not the current viewport, ABAQUS/CAE deletes a viewport when you click its delete button. As
with any canvas object, you cannot restore a viewport once you have deleted it. If you try to use the
delete button to delete the current viewport (indicated by a red border), ABAQUS/CAE does the
following:
· If the current viewport is the only viewport on the canvas, ABAQUS/CAE does not allow you to
delete it.
· If you have created additional viewports on the canvas, ABAQUS/CAE deletes the current
viewport and selects one of the additional viewports to be the current viewport. You cannot
control which viewport ABAQUS/CAE selects to be current.
To delete a selected viewport, you can also click the delete tool in the Canvas toolbox or select
Canvas->Delete from the main menu bar. However, you must first select the viewport. If the viewport
decorations are hidden, the viewport title bar and the delete button are also hidden. However, you can
still use the Canvas menu items or the tools in the toolbox to perform the same functions as the delete
button.
3-211
Managing objects on the canvas
By default, ABAQUS/CAE displays a title bar across the top of a viewport. The title bar contains the
viewport name and additional information to help you identify the context of the viewport. If the title
bar is not helpful, you can remove it to create additional screen space. You cannot show the viewport
title without also showing the viewport border.
To show and hide the title of selected viewports:
· Canvas->Show Viewport Title to show the title bar of the selected viewports.
· Canvas->Hide Viewport Title to hide the title bar of the selected viewports.
If no viewports are selected, the Show Viewport Title and Hide Viewport Title menu items are
unavailable.
Tip: You can also show and hide the titles of selected viewports by clicking and
3-212
Managing objects on the canvas
If no viewports are selected or the selected viewport is also the current viewport, the Show
Viewport Decorations and Hide Viewport Decorations menu items are unavailable.
Tip: You can also show and hide the decorations of selected viewports by clicking and
· ``Editing canvas annotation color, line, and font attributes, '' Section 7.4.6
3-213
Managing objects on the canvas
attributes of canvas annotations. Canvas annotations are not saved when you exit the ABAQUS/CAE
session.
Figure 7-4 shows text strings and arrows used to annotate a model.
Text
Text annotations can consist of any characters that can be displayed using the fonts available
on your workstation. ABAQUS/CAE restricts each annotation to a single line of text.
However, you can place text anywhere on the drawing area, and you can move a text
annotation after you have created it. Different text annotations can be displayed using different
fonts, but you cannot change fonts in a single text annotation.
Arrows
You can create arrows anywhere in the drawing area; typically, an arrow will connect a text
annotation to a point within a viewport. Arrows can have one of several different thicknesses
and line styles and can be displayed in any color available on your workstation. You can
modify and move an arrow after you have created it.
For information about viewport annotations, which are annotations that ABAQUS/CAE creates
automatically within a viewport, see Chapter 38, "Customizing viewport annotations."
Tip: You can also create a text annotation by clicking in the Canvas toolbox.
3-214
Managing objects on the canvas
2. Move the cross-hair to the desired position of the text annotation, and click mouse button 1. (Text
can be placed anywhere on the drawing area.)
A box appears; the contrasting color of the border indicates it is selected.
· Press [Enter], or
Tip: To edit an existing text annotation, click the text to select it. A box surrounds the text, and
you can position the cursor within the box and add or delete text. You can also move the selected
text annotation by dragging its handle to a new position on the canvas.
1. From the main menu bar, select Canvas->Create Arrow to create an arrow.
The cursor changes to a cross-hair.
Tip: You can also create an arrow by clicking in the Canvas toolbox.
2. Click the desired position of the arrow's tail and head, in that order.
The arrow appears in the desired location. You cannot reverse the direction of an arrow.
3-215
Managing objects on the canvas
to a box-in-box: . A selected text annotation is surrounded by a box and has a handle to the left, as
shown in the following figure:
A selected arrow has handles at each end, as shown in the following figure:
If another annotation was already selected, it becomes unselected and its handles disappear. To select
additional annotations, [Shift]+Click instead of clicking. To unselect an annotation, [Ctrl]+Click the
annotation.
An additional method for selecting multiple annotations is to drag a rectangle around those
annotations; you can select viewports at the same time by including them in the rectangle. To select
multiple canvas objects your rectangle must begin in an unused portion of the drawing area and must
completely enclose the objects you want to select.
3-216
Managing objects on the canvas
If you select a text annotation, a box surrounds the text with a handle at the left end; if you select
an arrow, handles appear at each end.
to a four-headed arrow while you move the text. You can drag the text anywhere on
the canvas, even outside the drawing area.
ABAQUS/CAE applies your customizations not only to the annotations you have selected but also to
any new annotations you subsequently create.
3-217
Managing objects on the canvas
You can also copy the attributes of a text annotation and apply those attributes to another text
annotation. Similarly, you can copy the attributes of an arrow annotation and apply those attributes to
another arrow annotation. For more information, see ``Copying and applying canvas annotation
attributes,'' Section 7.4.7.
To edit annotation attributes:
Tip: You can also display the Canvas Annotations dialog box by clicking from the
Canvas toolbox.
4. From the Canvas Annotations dialog box, select the Text tab or the Arrow tab, and select the
desired color, line style, line thickness, or font attributes.
5. To close the Canvas Annotations dialog box, double-click the top left corner.
If you subsequently create a new annotation, ABAQUS/CAE displays it using the customized
properties.
3-218
Managing objects on the canvas
Tip: You can also display the Canvas Annotations dialog box by clicking from the
Canvas toolbox.
3. From the Canvas Annotations dialog box, click Copy Options to copy the attributes of the
selected annotation.
If more than one annotation is selected, the Copy Options button is disabled.
6. From the Canvas Annotations dialog box, click Apply to Selection to apply the saved attributes
to the selected annotations.
The attributes of the selected annotations change.
7. To close the Canvas Annotations dialog box, double-click the top left corner.
3-219
Manipulating the view and controlling perspective
4-220
Manipulating the view and controlling perspective
You can manipulate this view using the pan, rotate, magnify, box zoom, and auto-fit tools on the
toolbar. For example, you might want to pan and zoom a contour plot to view an area of stress
concentration. The view manipulation tools allow you to perform the following operations:
· Move the view horizontally and vertically; that is, pan the view.
· Rescale the view to fill the viewport; that is, auto-fit the view.
· Use the Views toolbox to apply a predefined or user-defined view or to save a user-defined
view.
Clicking a view manipulation tool puts you into the corresponding view manipulation mode. You then
manipulate the view in a particular viewport by moving the cursor to that viewport and dragging or
clicking as necessary. To exit a view manipulation mode, do one of the following:
You can use the view manipulation tools as many times as necessary to reach the desired view, and
you can perform the view manipulation in any viewport, regardless of what is being displayed.
ABAQUS/CAE stores the eight most recent views from each viewport, and you can use the cycle view
manipulation tool to cycle backward and forward through these views.
By default, ABAQUS/CAE displays the image using a simple wireframe representation while you
manipulate the view of an object, regardless of whether the current render style is wireframe, filled,
hidden line, or shaded. The image reverts to the original render style when you complete the
manipulation. You can control this behavior by setting the Drag Mode in the View Options dialog
box.
If you prefer to use menus rather than the tools on the toolbar, you can access all of the view
manipulation tools through the View menu on the main menu bar. In addition, you can apply
predefined and user-defined views using the Views toolbox, and you can numerically specify a precise
4-221
Manipulating the view and controlling perspective
view using the dialog box that appears when you select View->Specify from the main menu bar. For
more information on custom and numerically specified views, see ``Custom views,'' Section 8.1.8, and
``Numerically specifying a view,'' Section 8.1.9, respectively.
Alternatively, you can enter three of the view manipulation modes by using a combination of keyboard
and mouse actions.
· To rotate the view, press Ctrl+Alt, and hold down mouse button 1.
· To pan the view, press Ctrl+Alt, and hold down mouse button 2.
· To magnify or reduce the view, press Ctrl+Alt, and hold down mouse button 3.
To exit a view manipulation mode after using one of the preceding actions, simply release the mouse
button. You can customize the key configurations associated with these actions; for more information
see ``Customizing X resources,'' Section 6.1.
When you select the pan tool and the viewport in which to work, ABAQUS/CAE enters pan
mode, as indicated by the cursor.
The position of your view of the model changes as you click and then drag the cursor, and a
rubberband line indicates the amount of translation. The initial location of the cursor is not important,
as long as you place it within the viewport. Cursor motion is limited only by the physical bounds of
your monitor, and panning will continue even if you move the cursor outside the viewport or window.
When you select the rotate tool and the viewport in which to work, ABAQUS/CAE enters rotate
mode. In this mode the cursor changes to a right facing arrow, and a large circle appears in the
viewport. Your view of the model rotates as you drag the cursor, and a rubberband line indicates the
amount and the direction of rotation. As you rotate your view of the model, the view triad indicates the
orientation of the global coordinate system.
The circle that is drawn when you enter rotate mode represents the silhouette of an imaginary sphere
that surrounds the object. When you drag the mouse inside the circle, you might imagine that you are
4-222
Manipulating the view and controlling perspective
actually rotating the sphere, as you would a trackball. Your model is attached to the center of the
sphere, so that rotating the sphere causes your view of the model to rotate as well.
You determine the axis of rotation as you move the cursor over the surface of the imaginary sphere.
The rubberband line represents the intersection of a cutting plane with the sphere's surface, and the
rotation axis is normal to this cutting plane. The angle of rotation is twice the angle made by the
rubberband line on the sphere's surface, so that dragging all the way across the circle produces a 360°
rotation. Figure 8-1 illustrates the imaginary sphere and a rubberband line being dragged across its
surface.
When you drag outside the circle, the rubberband line is superimposed on the circle, and your view of
the object simply rotates about an axis normal to the screen and passing through the center of the
circle. In this case the rubberband line directly represents the angle through which the object has
rotated.
It is usually easier to obtain a desired rotation by performing a sequence of smaller rotations rather
than one large one. If you need to abandon the rotation and return to a known orientation, use either
the predefined views in the Views toolbox or the cycle view tool .
When you select the magnify tool and the viewport in which to work, ABAQUS/CAE enters
magnify mode, as indicated by the magnify cursor . When you drag the cursor to the right while in
4-223
Manipulating the view and controlling perspective
magnify mode, your view of the model expands within the viewport, and a rubberband line indicates
the relative magnification. Similarly, when you drag the cursor to the left, your view of the model
contracts, and a rubberband line indicates the relative reduction. The dragging action must start in the
viewport, but you can continue to drag within the limits of your monitor. You can also drag repeatedly
to achieve the desired view. The magnify tool recognizes only the horizontal component of your
dragging motion, as indicated by the rubberband line. Consequently, you can achieve finer control by
dragging diagonally across the screen, since this results in a smaller horizontal component of the
cursor's motion than dragging the same distance horizontally.
If you lose track of your position, you may want to use the auto-fit tool to rescale the view to fit
the viewport.
When you select the box zoom tool and the viewport in which to work, ABAQUS/CAE enters
box zoom mode, as indicated by a rectangular cursor with a small arrow in one corner. You use this
tool to select a rectangular area of your model; ABAQUS/CAE enlarges your view of the selected
portion of your model to fill the viewport.
Use the auto-fit tool from the toolbar to quickly adjust your view of the model so that the model
fills the viewport and is centered within it. When you fit a view, the orientation does not change, as
indicated by the view triad.
If you have only one viewport, auto-fitting occurs as soon as you click the auto-fit tool. If you have
more than one viewport, select the auto-fit tool and then place the cursor over the viewport you want to
rescale. The cursor changes; click, and ABAQUS/CAE auto-fits the view.
A separate option, Auto-fit after view rotations, is available when you select View->View Options
from the main menu bar. You use this option to control whether or not ABAQUS/CAE automatically
rescales the view to fit the viewport as you rotate. For more information on using this option, see
``Rotating the view,'' Section 8.4.2.
4-224
Manipulating the view and controlling perspective
When you select the cycle tool and the viewport in which to work, ABAQUS/CAE enters cycle
mode, as indicated by a cursor in the form of a two-way arrow. You can cycle through the eight most
recent views in each viewport.
To cycle through previous views, click in the viewport whose view you want to change. To control the
direction of cycling, click Backward or Forward in the prompt area. The default is to cycle backward.
After you cycle backward to the oldest available view, continued clicking has no effect. Similarly, after
you cycle forward to the most recent view, continued clicking has no effect.
When you select the view toolbox from the toolbar, ABAQUS/CAE displays the Views toolbox
that allows you to apply a custom view to the model in the selected viewport. (A view is the
combination of the position, orientation, and zoom factor of the model in the viewport.)
Custom views include seven predefined views (such as front and back) and up to four user-defined
views.
Predefined views
Predefined views are based on the six faces of an imaginary cube and an isometric view. The
view triad indicates the orientation of this imaginary cube within a viewport. Figure 8-2
illustrates the six predefined cube face views.
4-225
Manipulating the view and controlling perspective
User-defined views
You can use the view manipulation tools to position your view of a model in a viewport and
then click in the Views toolbox to save the view as one of four user-defined views.
You can use this saved view to restore the object in the viewport to a known orientation, and
you can apply a saved view to other viewports. Saved views are not stored between sessions.
The view consists of three components: orientation, zoom factor, and position. You can
choose whether or not all three of these components are saved using the Scale & Position
options, as follows:
Auto-fit
When you save a view after choosing this option, only the orientation is saved. When
you apply a view saved with this option, the saved orientation is applied, but the zoom
factor and position are adjusted to make the view fit the viewport.
Save current
When you save a view after choosing this option, the orientation, the zoom factor, and
the position are all saved. When you apply a view saved with this option, the saved
orientation, zoom factor, and position are all applied to the object in the viewport. To
compare different objects in different viewports by placing the viewports side-by-side
and applying a known orientation, zoom factor, and position to each, choose the Save
current option.
4-226
Manipulating the view and controlling perspective
You can bypass the view manipulation tools and specify a particular view numerically. Specifying a
view is useful if you want to reproduce a particular view between ABAQUS/CAE sessions or if
numerically specifying a view is simpler and more convenient than applying a series of view
manipulations. You can use the following methods to specify your view:
Rotation Angles
Enter three angles (µ1 , µ2 , µ3 ) representing the angles through which your view of the model
rotates about the screen or model 1-, 2-, and 3-axes, respectively. Rotations are interpreted in
the order (µ1 , µ2 , µ3 ), and a positive angle represents a right-handed rotation about the axis.
You must choose one of the following modes to apply the rotation:
· Increment About Model Axes. When you choose Increment About Model Axes,
ABAQUS/CAE simply applies the rotation to the current view. Figure 8-3 shows the
result of applying an incremental model axes rotation of 90, 0, 0 from the isometric view.
· Increment About Screen Axes. The screen X-axis is horizontal, the Y-axis is vertical,
and the Z-axis is out of the screen. The origin of the screen axes is the center of the
viewport. When you choose Increment About Screen Axes, ABAQUS/CAE simply
applies the rotation to the current view. Figure 8-4 shows the result of applying an
incremental screen axes rotation of 90, 0, 0 from the isometric view.
· Total Rotation From (0,0,1). When you choose Total Rotation From (0,0,1),
4-227
Manipulating the view and controlling perspective
ABAQUS/CAE first rotates the view to the default position (a view looking down the
3-axis with the 1- and 2-axes in the plane of the screen) and then applies the desired
rotation. Figure 8-5 shows the result of applying a total rotation of 90, 0, 0 from the
isometric view.
Viewpoint
When you choose Viewpoint , you enter three values representing the 1-, 2-, and 3-position of
an observer. ABAQUS/CAE constructs a vector from the origin of the model to the position
that you specify and rotates your view of the model so that this vector points out of the screen.
Figure 8-6 shows the result of applying a viewpoint of 1, 1, 1 (an isometric view) and a
viewpoint of 1, 0, 0.
When you use the Viewpoint method to specify a view, you can also specify the Up vector.
ABAQUS/CAE positions your view of the model so that this vector points upward. Figure 8-7
shows the result of applying an up vector of 0, 1, 0 and an up vector of 0, -1, 0 to an isometric
view.
4-228
Manipulating the view and controlling perspective
Zoom
Enter a value representing a magnification factor. A value greater than 1 expands your view of
the model in the viewport; for example, a Zoom factor of 2 doubles the size of your view of
the model. A value between 0 and 1 contracts your view of the model in the viewport; for
example, a value of 0.25 contracts your view of the model to a quarter of its original size. The
value must be greater than zero.
You must choose one of the following methods to apply the zoom:
· Absolute. When you choose Absolute, ABAQUS/CAE first fits the view to the viewport
and then applies the desired Zoom factor.
· Relative. When you choose Relative, ABAQUS/CAE applies the Zoom factor to the
current view.
Pan
Enter values that ABAQUS/CAE uses to Pan your view of the model to a specified horizontal
and vertical position within the viewport. ABAQUS/CAE first centers the view in the
viewport and then moves it to the desired position. The values that you enter indicate the
desired position of your view of the model based on fractions of the 1- and 2-dimensions of
the viewport. Positive 1-values indicate a position toward the right edge of the viewport, and
positive 2-values indicate a position toward the top of the viewport. For example, if the
viewport is 200 mm wide and 100 mm tall and you enter values of 0.5, -0.1 in the Fraction of
viewport to pan (X,Y) field, ABAQUS/CAE positions your view of the model 100 mm
toward the right and 10 mm down from the center of the viewport.
4-229
Manipulating the view and controlling perspective
You can use the View->Viewport Annotations menu item to request or suppress the display of the
triad and to control the triad's position and appearance. You can also control the triad's color, labels,
and label font.
To control triad display options:
2. Click the Triad tab, and toggle Show triad to display or suppress the triad.
When Show triad is toggled on, Position and Attributes options become available.
3. If Show triad is toggled on, enter percentage values for the triad X and Y positions in the %
Viewport X and % Viewport Y boxes, respectively.
A value of 0 for % Viewport X moves the triad origin to the extreme left of the viewport while a
value of 100 moves it to the extreme right. A value of 0 for % Viewport Y moves the triad origin
to the extreme bottom of the viewport, while a value of 100 moves it to the extreme top.
4. Click the Color arrow and select a color option from the list that appears.
The specified color name appears in the color box.
5. Click the Labels menu button and select either numerical or alphabetical labeling for the triad.
The specified style appears in the Labels box.
6. Click Set Label Font to set the font type, size, and style using the dialog box that appears.
4-230
Manipulating the view and controlling perspective
You can use the View->View Options menu item or the and icons located in the toolbar to
control perspective.
To control perspective:
Tip: You can also control perspective using the and icons located in the toolbar.
4-231
Manipulating the view and controlling perspective
Use the pan tool from the toolbar to move the view horizontally and vertically within the
viewport.
To pan the view:
1. From the toolbar, click the pan tool to enter pan mode.
Tip: You can also select View->Pan from the main menu or press [F2].
2. Position the cursor in the viewport whose view you want to change.
3. Drag the cursor in any direction until you obtain the desired view.
The position of your view of the model in the viewport changes as you drag the cursor, and a
rubberband line indicates the amount of translation.
Note: The initial location of the cursor is not important, as long as you place it within the viewport. Cursor motion is limited
only by the physical bounds of your monitor, and panning will continue even if you move the cursor outside the viewport or
window.
To return to the original view, drag the cursor back to the origin of the rubberband line.
Tip: Use the cycle view manipulation tool to return to the previous view.
4-232
Manipulating the view and controlling perspective
Use the rotate tool from the toolbar to rotate the view within the viewport. Using a separate
option you can control whether or not ABAQUS/CAE rescales your model to fit the viewport as you
rotate.
To rotate the view:
1. From the toolbar, click the rotate tool to enter rotate mode.
Tip: You can also select View->Rotate from the main menu or press [F3].
2. Position the cursor in the viewport whose view you want to change.
A large circle appears in the viewport and the cursor changes to a right facing arrow.
To rotate the view about the normal to the screen, move the cursor outside the circle and drag it
clockwise or counterclockwise.
To return to the original view, drag the cursor back to the origin of the rubberband line.
Tip: Use the cycle view manipulation tool to return to the previous view.
4-233
Manipulating the view and controlling perspective
2. Toggle Auto-fit after view rotations on to automatically rescale the view to fit the viewport as
you rotate; toggle it off to disable automatic rescaling during rotation.
Use the magnify tool from the toolbar to change the scale of the view in the viewport.
To magnify or reduce the view:
1. From the toolbar, click the magnify tool to enter magnify mode.
Tip: You can also select View->Magnify from the main menu or press [F4].
2. Position the cursor in the viewport whose view you want to change.
· To magnify the view (zoom in), drag the cursor to the right of the starting point.
· To reduce the view (zoom out), drag the cursor to the left of the starting point.
ABAQUS/CAE draws a horizontal rubberband line from the starting point as you drag the cursor
across the screen. The rubberband line indicates the amount of zooming that has been applied, and
the amount of zooming is proportional to only the horizontal component of your dragging motion.
To return to the original view, drag the cursor back to the origin of the rubberband line.
4-234
Manipulating the view and controlling perspective
Tip: Use the cycle view manipulation tool to return to the previous view.
Use the box zoom tool from the toolbar to enlarge the view so that a selected area fills the
viewport.
To zoom in to a selected area of the view:
1. From the toolbar, click the box zoom tool to enter zoom mode.
Tip: You can also select View->Box Zoom from the main menu or press [F5].
2. Position the cursor in the viewport whose view you want to change.
The cursor changes to a rectangle with a small arrow in one corner.
6. Repeat Steps 2 through 5 as many times as necessary to achieve the desired view.
4-235
Manipulating the view and controlling perspective
Tip: Use the cycle view manipulation tool to return to the previous view.
Use the auto-fit tool from the toolbar to quickly pan and magnify or reduce a view so that the
view fills the viewport and is centered within it. When you fit a view, the orientation remains fixed, as
indicated by the view triad.
From the toolbar, click the auto-fit tool to enter auto-fit mode.
Tip: You can also select View->Auto-fit from the main menu or press [F6].
If you have only one viewport, ABAQUS/CAE immediately scales the view to fit the viewport without
changing the orientation, centers the view within the viewport, and exits fit mode. If you have more
than one viewport, select the auto-fit tool and then place the cursor over the viewport you want to
rescale. Click in the viewport to auto-fit; ABAQUS/CAE rescales the view and exits fit mode.
Tip: Use the cycle view manipulation tool to return to the previous view.
For information on how to automatically rescale the view to fit the viewport during rotation, see
``Rotating the view,'' Section 8.4.2.
4-236
Manipulating the view and controlling perspective
Use the cycle tool from the toolbar to cycle through previous views; ABAQUS/CAE saves the
eight most recent views for each viewport.
To cycle through previous views:
1. From the toolbar, click the cycle tool to enter cycle mode.
Tip: You can also select View->Previous Views from the main menu or press [F7].
2. Position the cursor in the viewport whose view you want to change (the cursor changes to a
two-way arrow); then click.
3. To control the direction of cycling, click Backward or Forward in the prompt area. The default is
to cycle backward.
4. Repeat Steps 2 and 3 as many times as necessary to achieve the desired views.
After you cycle backward to the oldest available view, continued clicking has no effect. Similarly,
after you cycle forward to the most recent view, continued clicking has no effect.
4-237
Manipulating the view and controlling perspective
user-defined settings. To display the Views toolbox, click the views tool from the toolbar; the
Views toolbox is illustrated in the following figure:
· Front, Back, Top, Bottom, Left, and Right: equivalent to observing the model from the six sides
of a cube.
· Iso: an isometric view. This is the default orientation for three-dimensional models.
· User1, User2, User3, and User4: four user-defined views. See ``Saving a user-defined view,''
Section 8.4.8, for a description of how to save a user-defined view.
4. To close the Views toolbox, double-click the close button in the upper-left corner of the toolbox.
4-238
Manipulating the view and controlling perspective
Use the save tool in the Views toolbox to open the Save Views dialog box and save a
user-defined view. The Save Views dialog box is illustrated in the following figure:
Use the Scale & Position options to determine whether the saved view contains zoom factor and
position information.
To save a user-defined view:
4-239
Manipulating the view and controlling perspective
3. From the Save View dialog box, choose the desired Scale & Position behavior:
· Choose Auto-fit to save only the orientation of the view. When you apply a view saved with
this option, the saved orientation is applied, but the scaling factor and position are adjusted to
make the view fill the viewport.
· Choose Save current to save the orientation, the zoom factor, and the position of the view.
When you apply a view saved with this option, the saved orientation, scaling factor, and
position are all applied.
4. In the View Name list in the Save Views dialog box, click the name of the tool you will use to
recall this view.
If you overwrite one of the six custom views--front, back, top, bottom, left, right--the other five
views still retain their original definitions; that is, they do not become rotated to positions
orthogonal to your saved view.
6. To remove the Views toolbox, double-click the close button in the upper-left corner of the
toolbox.
You can specify the angles through which ABAQUS/CAE will rotate your view of the model
about the model or screen 1-, 2-, and 3-axes. You can also choose to rotate your view of the
model from an absolute position (a ``Front'' view) or from the current position.
4-240
Manipulating the view and controlling perspective
Viewpoint
You can specify the coordinates of a vector along which an observer views your model. You
can also orient the global 1-, 2-, and 3-axes within the viewport by specifying a vector
representing the ``up'' direction.
Zoom
You can specify a zoom factor that expands or contracts the view. You can also choose to
zoom the view relative to an absolute size of the objects in the viewport (the default size with
a zoom factor of one applied) or relative to the current size of the objects in the viewport.
Pan
You can specify that your view of the model will be moved to a certain position within the
viewport. The values correspond to fractions of the viewport dimensions and are relative to the
center of the viewport.
For a more detailed explanation, see ``Numerically specifying a view,'' Section 8.1.9.
To specify the view:
2. From the Specify View dialog box, select the desired Method and do one of the following:
· If you selected the Rotation Angles method, enter the rotation angles about the X-, Y-, and
Z-axes (µx , µy , µz ); a positive number corresponds to a counterclockwise rotation about each
axis.
Use the Mode button to specify how ABAQUS/CAE is to apply your rotation:
- Choose Increment About Model Axes to apply the rotation to the model axes of the
current view.
- Choose Increment About Screen Axes to apply the rotation to the screen axes of the
current view. The screen X-axis is horizontal, the Y-axis is vertical, and the Z-axis is out of
the screen. The origin of the screen axes is the center of the viewport.
- Choose Total Rotation From (0,0,1) to first rotate the view to the default position (a view
looking down the 3-axis with the 1- and 2-axes in the plane of the screen) and then apply
the rotation.
· If you selected the Viewpoint method, enter the X-, Y-, and Z-coordinates of the viewpoint
vector and the coordinates of the up vector.
· If you selected the Zoom method, enter the zoom factor and choose either Absolute or
Relative magnification. A zoom factor greater than one expands your view of the model, and a
zoom factor between zero and one contracts your view of the model.
4-241
Manipulating the view and controlling perspective
· If you selected the Pan method, enter the values indicating how you want to position your
view of the model within the viewport. The first value represents a horizontal position, and the
second value represents a vertical position.
3. Click OK to apply your specified view and to close the Specify View dialog box.
Tip: Use the cycle view manipulation tool to return to the original view.
4-242
Selecting objects within the viewport
Selecting dialog box options is discussed in ``Interacting with dialog boxes,'' Section 6.3. Selecting
canvas objects is discussed in ``Selecting viewports,'' Section 7.3.2, and ``Selecting canvas
annotations,'' Section 7.4.4.
· ``What objects can you select from the viewport?,'' Section 9.1.1
· ``Understanding the correspondence between geometric and physical objects, '' Section 9.1.2
You can select objects in the viewport only during certain procedures, such as those listed below:
5-243
Selecting objects within the viewport
· Editing a feature
In most circumstances only objects that are appropriate for the current procedure are available for
selection. For example, the first step in partitioning an edge is selecting the edge of interest. Therefore,
at this point in the procedure you can select only an edge; you cannot select a cell, a face, or a vertex.
Messages in the prompt area guide you through the steps of a procedure and indicate which types of
objects are available for selection.
In some circumstances ABAQUS/CAE cannot determine which objects are appropriate for selection
and does not limit your selection. For example, when you are creating a set you can select from cells,
faces, edges, and vertices to include in the set, and ABAQUS/CAE allows you to select any of these
objects. When you make a selection from the viewport, ABAQUS/CAE allows you to cycle through
the available objects until the desired object is selected. This ambiguity is described in ``Cycling
through valid selections,'' Section 9.2.5. You may find it easier to use the selection filters to limit the
type of object you can create. For more information, see ``Using the selection options,'' Section 9.3.
5-244
Selecting objects within the viewport
The end surfaces of these parts are represented by the vertices on either side of the edge, and the
circumferential surface is represented by the line joining the vertices. To select a wire part, you can
click the edge, and, if necessary, ABAQUS/CAE prompts you to specify the surface of interest.
Likewise, axisymmetric shells are also represented by edges in the geometric model (see Figure 9-3).
You can select the axisymmetric shell by clicking the edge in the viewport, and, if necessary,
ABAQUS/CAE prompts you to specify either the inside surface or the outside surface of the shell. You
must select either the inside or the outside surface if you are applying a prescribed condition or contact
definition to the surface. For example, if you want to apply a pressure load to a shell, you must specify
which side of the shell should receive the load.
For more information on selecting surfaces, see ``Specifying a particular side or end of a region,''
Section 45.2.5. For more information on modeling space, see ``The relationship between parts and
features,'' Section 14.3.1, and ``Part modeling space,'' Section 14.4.1.
5-245
Selecting objects within the viewport
· ``Using the face angle method to create a surface from an orphan mesh,'' Section 9.2.3
· To select a point, click the corresponding point marker. The color of the point marker
changes color when selected. Vertices that you can select are marked by small, filled
circles, and datum points are marked by small, unfilled circles. (See ``Understanding the
role of datum geometry,'' Section 41.1, for information on datum points.) Edge midpoints
and arc centers that you can select are marked by small diamonds.
Note: Some of the selection markers that appear when you are using the Sketch
module are different from those described here. For information on selecting objects
while using the Sketch module, see ``The Sketcher cursors and preselection,'' Section
22.4.5.
· To select an edge, click the edge while positioning the cursor away from any vertex.
Selected edges are highlighted.
· To select a face, click the face while positioning the cursor away from any edge or vertex.
Selected faces are highlighted with a grid pattern. (The grid pattern is unrelated to mesh
element location.)
· To select a cell, click any of its faces. All edges of selected cells are highlighted.
If a selection is ambiguous, ABAQUS/CAE displays buttons in the prompt area that allow you
5-246
Selecting objects within the viewport
to cycle between the valid choices and to confirm your selection. For more information, see
``Cycling through valid selections,'' Section 9.2.5.
Once you select an object, any objects previously selected in the current viewport are
unselected automatically.
When you have finished selecting and unselecting items in the viewport, click mouse button 2 to
confirm your selection. You might find it useful to use the selection option tools to adjust the shape of
the drag-select region. You can also choose which objects are selected by the drag-select region. To
access the selection option tools, click in the prompt area. For more information, see ``Modifying
the shape of the drag-select region,'' Section 9.3.4, and ``Choosing which objects are selected by the
drag-select region,'' Section 9.3.5.
in the prompt area. For more information, see ``Modifying the shape of the drag-select region,''
Section 9.3.4, and ``Choosing which objects are selected by the drag-select region,'' Section 9.3.5.
Detailed instructions for drag-selecting multiple objects:
5-247
Selecting objects within the viewport
1. Imagine a rectangle that encloses only the objects you want to select.
2. Click at one corner of the rectangle and, while continuing to press the mouse button, drag until you
have enclosed all the objects.
4. Click mouse button 2 to indicate that you have finished selecting objects.
ABAQUS/CAE selects every adjacent element from the target face until the angle between the element
faces is equal to or exceeds the face angle. Figure 9-4 illustrates an exhaust manifold and the effect of
5-248
Selecting objects within the viewport
the face angle selection method given a target face on a flange and a face angle of 90°.
Figure 9-4 Select a target face and a face angle to create a surface.
After you use the face angle method, you can [Shift]+Click on additional elements to append them to
your selection, and you can [Ctrl]+Click on elements to unselect them. For more information, see
``Combining selection techniques,'' Section 9.2.4.
When you are creating a surface from an orphan mesh, you use the menu button in the prompt area to
choose between the selection methods-- Individual and Face angle.
5-249
Selecting objects within the viewport
3. Finally, you use [Shift]+Click to add nodes to your set and then click mouse button 2 to indicate
you have finished selecting.
You may find it useful to adjust the view orientation to make particular items in the viewport more
accessible. You can adjust the view orientation at any point during the selection process. For
information on the view manipulation tools, see Chapter 8, "Manipulating the view and controlling
perspective."
Tip: To unselect all the objects, click an unused part of the current viewport.
· Imagine a small square surrounding the cursor. When you click an object, any other valid objects
of the same type that fall inside this square are also considered to be possible selections. For
example, if you select an edge that is positioned very close to another edge, ABAQUS/CAE may
consider both edges to be possible selections.
The size of the square is independent of the monitor size, the viewport size, and the dimensions of
the model. It also remains constant when you zoom in and out on your model. Therefore, you can
select a specific object in the viewport more precisely by zooming in on your model to increase the
distance between objects.
· If your model is three-dimensional, imagine a line that is perpendicular to the screen and that
passes through the cursor and into the model. When you select an object, any valid objects of the
5-250
Selecting objects within the viewport
same type that intersect this line are considered to be possible selections. (Rotating your model
may remove some of the ambiguity.)
ABAQUS/CAE reduces the potential for ambiguity by filtering your selection against the current
procedure whenever possible. For example, if you are partitioning a cell, ABAQUS/CAE prompts you
to select the cell to partition. When you make a selection, ABAQUS/CAE considers only cells to be a
valid selection. Conversely, if you are creating a geometry set, ABAQUS/CAE considers cells, faces,
edges, and vertices to be a valid selection and the potential for ambiguity is increased.
If your selection is ambiguous, ABAQUS/CAE displays buttons in the prompt area that allow you to
cycle through all of the possible selections, as shown here:
Use the Next and Previous buttons to cycle forward and backward through all of the objects in the
viewport that are possible selections; each object becomes highlighted in turn. When the object of your
choice is highlighted, click OK or click mouse button 2 to confirm your selection. (You can also click
mouse button 3 in the drawing area to reveal a menu of the options in the prompt area.)
objects from the viewport. The selection options tool appears on the prompt line when you are
prompted to make a selection from the viewport, as shown in Figure 9-5.
Figure 9-5 The selection options tool appears on the prompt line when you are prompted to make a
selection from the viewport.
This section describes the selection options. The following topics are covered:
5-251
Selecting objects within the viewport
· ``Filtering your selection based on the position of the object, '' Section 9.3.3
· ``Choosing which objects are selected by the drag-select region,'' Section 9.3.5
From the prompt area, click the selection options tool to configure the selection options.
Selection options remain in effect only during the current procedure. When you enter the next
procedure, the selection options revert to their default settings.
Figure 9-6 shows the layout of the selection options tools.
When you click on the selection options tool , ABAQUS/CAE displays the Options toolbox and
configures the contents based on the current procedure. The Options toolbox allows you to control the
5-252
Selecting objects within the viewport
Object type
If the current viewport contains an ABAQUS/CAE part or part instance, you can select one of
the following filters:
· All
· Vertices
· Edges
· Faces
· Cells
· Skins
By default, ABAQUS/CAE selects from all vertices, edges, faces, and cells. You can select a
skin from the viewport only after you select the skins filter.
Similarly, if you are selecting elements from an orphan mesh in the current viewport (to assign
an element type, for example), you can select one of the following filters:
· All
· Zero-dimensional elements
· One-dimensional elements
· Two-dimensional elements
· Three-dimensional elements
viewport. When you click on the selection options tool , ABAQUS/CAE displays the Options
toolbox, and you can select the following:
Toggle on this tool to select only the objects closest to the front of the screen. This tool
is toggled on by default.
If you toggle off this tool, ABAQUS/CAE allows you to cycle through all of the possible
selections. Use the Next and Previous buttons in the prompt area to cycle forward and
backward through all of the objects in the viewport that are possible selections; each object
5-253
Selecting objects within the viewport
becomes highlighted in turn. For more information, see ``Cycling through valid selections,''
Section 9.2.5.
This filter applies to vertices, edges, faces, and cells of an ABAQUS/CAE native part and to
nodes and elements of an orphan mesh.
· Select objects located both outside and inside a part. This tool is selected by default.
selection options tool , ABAQUS/CAE displays the Options toolbox, and you can choose one of
the following:
Rectangle
Click to indicate one corner of the rectangle, and drag the cursor to the second corner.
This tool is selected by default.
Circle
Click to indicate the center of the circle, and drag the cursor to a point on the
circumference.
Polygon
Click to indicate one vertex of the polygon, and drag the cursor to the second vertex.
You then continue to click on each vertex of the polygon. Click mouse button 2 to indicate
you have finished entering vertices. There is no limit to the number of vertices in the
polygon.
5-254
Selecting objects within the viewport
The selection tools allow you to choose which objects are selected by the drag-select region. When you
click on the selection options tool , ABAQUS/CAE displays the Options toolbox, and you can
choose one of the following:
Inside
Select only the objects that fall inside the drag-select region.
Select only the objects that fall inside or cross the drag-select region. This tool is
selected by default.
Crossing
Select only the objects that fall outside or cross the drag-select region.
Outside
Select only the objects that fall outside the drag-select region.
5-255
Tuning display performance
To locate the options referred to in this chapter, select View->View Options from the main menu bar.
6-256
Tuning display performance
· If you run ABAQUS/CAE on a remote machine and display the images on a local machine,
6-257
Tuning display performance
OpenGL may generate excessive network traffic, especially for large models.
· If you use wireframe render style, X11 graphics may perform adequately while saving memory
resources in comparison to OpenGL graphics.
6-258
Tuning display performance
· General:
- Control perspective. For more information, see ``Controlling perspective,'' Section 8.3.
- Choose the drag mode. For more information, see ``Controlling drag mode,'' Section 10.1.
- Enable or disable the automatic fitting of your view to the viewport after rotations. For
more information, see ``Rotating the view,'' Section 8.4.2.
· Hardware :
Tune performance using options for double buffering, display lists, and graphics drivers. For
more information on performance options, see Chapter 10, "Tuning display performance."
2. Use the tabbed pages in the dialog box to customize object appearance and to improve display
performance.
6-259
Printing canvas objects
· ``Controlling the destination and appearance of printed images, '' Section 11.2
For additional information on configuring printers, see the ABAQUS Site Guide.
PostScript
PostScript is the recognized standard for desktop publishing. PostScript is actually a
programming language whose instructions and data are usually stored in an ASCII format that
can be transferred easily between operating systems. You can print an image directly to a
PostScript printer, or you can save the same image in a PostScript file. When you select the
PostScript format, ABAQUS/CAE generates either a compressed bitmap representation or a
vector representation of your image, according to the following convention:
· In general, ABAQUS/CAE creates a vector representation of your image when you print
7-260
Printing canvas objects
wireframe render style plots. The Visualization module creates a vector representation of
your image when you print an X-Y plot, a wireframe undeformed or deformed plot, or a
wireframe symbol plot having wireframe arrowheads.
· ABAQUS/CAE creates a bitmap representation of your image when you print a hidden
line or shaded render style plot. The Visualization module also creates a bitmap
representation of your image when you print a filled render style plot or a symbol plot
having filled arrowheads. Since contour plots are considered filled plots, they also
generate a bitmap representation of your image.
For efficiency when producing bitmap images, you should minimize the size of your image
and limit the resolution of the image to, at most, the resolution of the device on which the
image is to be printed or displayed.
Encapsulated PostScript
Encapsulated PostScript (EPS) is a variation of PostScript that describes a single graphic
designed to be included in a larger document without modification. EPS files are identical to
PostScript files except for some information that describes the size and positioning of the
image. As a result, the above discussion about vector and bitmap representations of your
image applies equally to the EPS format. Most word processing and graphics applications
support the inclusion of EPS files.
TIFF
Tag Image File Format (TIFF) is a well-established bitmap image format that is recognized by
many software applications. The TIFF format supports both color and grayscale.
PNG
Portable Network Graphics (PNG) is an industry standard for storing bitmap images. The use
of PNG files has been popularized by the World Wide Web, and PNG images are displayed by
most popular web browsers running on a variety of operating systems. A PNG file consists of
color information and a compressed bitmap representation of the image.
· ``Controlling the destination and appearance of printed images, '' Section 11.2
7-261
Printing canvas objects
Orientation
The orientation of your page can be either portrait or landscape.
Aspect ratio
The aspect ratio is the ratio between the overall width and the overall height of the canvas
objects--viewports and annotations--that you select for printing. ABAQUS/CAE calculates the
size of your image by scaling the selected canvas objects so that the overall object size fits
within the available page size without changing the aspect ratio of the objects, as shown in
Figure 11-2. You cannot directly specify the size of your PostScript image; however, you can
control the aspect ratio by manipulating the objects on the canvas before printing them.
· ``Customizing the image sent to a PostScript printer or file, '' Section 11.2.5
· ``Controlling the destination and appearance of printed images, '' Section 11.2
7-262
Printing canvas objects
PNG-format file, ABAQUS/CAE determines the size of the image based on the size you specify and
the overall aspect ratio of the canvas objects. You can control the aspect ratio by manipulating the
objects on the canvas.
In the options dialog box (EPS Options, PNG Options, or TIFF Options) you can choose one of the
following methods to specify the size of the printed image:
· Use the size of the image on the screen. (ABAQUS/CAE indicates the current image size in the
options dialog box.) This method is the default.
· Set the width or height. You specify only one dimension; ABAQUS/CAE computes the other
dimension to maintain the aspect ratio of the canvas objects. When you are creating an EPS-format
file, you specify the width or height in either inches or millimeters. When you are creating a TIFF-
or a PNG-format file, you specify the width or height in screen pixels; increasing the number of
pixels increases the image size. The maximum image size allowed is 1280 ´ 1024 pixels.
· ``Controlling the destination and appearance of printed images, '' Section 11.2
7-263
Printing canvas objects
should adjust the objects on your canvas to match the dimensions and orientation that will appear in
the final application. Scaling and rotation do not distort or diminish the quality of vector representation
images.
· ``Controlling the destination and appearance of printed images, '' Section 11.2
· ``Customizing the image sent to a PostScript printer or file, '' Section 11.2.5
· ``Customizing the image saved in an Encapsulated PostScript file, '' Section 11.2.6
7-264
Printing canvas objects
another on the canvas, the obscured portion will not appear in the printed image. You can select the
format of the printed image, and additional options allow you to select the appearance of viewports in
the resulting image, and the color, resolution, orientation, and size of the image.
To create a printed image, select File->Print from the main menu bar. To configure your image, use the
Print dialog box that appears. For detailed help on the items within the dialog box, request
context-sensitive help on the individual items.
When you have finished selecting options, click OK in the Print dialog box to send the image to the
selected destination. ABAQUS/CAE closes the Print dialog box, sends the image to the selected
destination, and saves your print options for the duration of the session.
· ``Controlling the destination and appearance of printed images, '' Section 11.2
Viewport decorations
Use the Print viewport decorations (if visible) option to select whether your image will
include viewport decorations. Decorations are defined as the viewport border and the viewport
title.
If you want to print a viewport's decoration, it must first be visible on the canvas; you can turn
decorations off and on using the Canvas menu in the main menu bar.
Note: Toggling the Print viewport decorations (if visible) option off is the only way to
prevent the red border around the current viewport from appearing in your printed image;
the red border cannot otherwise be disabled.
7-265
Printing canvas objects
Viewport backgrounds
Use the Print viewport backgrounds option to control the appearance of a viewport's
background in your printed image. This option is available only when you choose either a
grayscale or a color image; when you choose black and white, ABAQUS/CAE always prints a
black image on a white background.
Note: Printing without the viewport background (so that the background appears
transparent or white) usually produces the most attractive hardcopy image.
2. From the Print menu button at the top of the dialog box, select either:
· All Canvas Objects to print all canvas objects, even if they lie outside the drawing area.
· Selected Canvas Objects to print only the canvas objects you have selected.
· When you choose PS (PostScript) or EPS (Encapsulated PostScript) format, viewports in your
image will have a white background.
· When you choose PNG or TIFF format, viewports in your image will have a transparent
background.
7-266
Printing canvas objects
5. When you have finished with the Print dialog box, click OK to generate the desired output.
ABAQUS/CAE generates the output and closes the Print dialog box. Your settings in the Print
dialog box are saved for the duration of the session.
· ``Controlling the destination and appearance of printed images, '' Section 11.2
Use this option to print black images on a white background. This option is useful for printing
wireframe and hidden-line images of parts, assemblies, and meshes, including any partitions
and datum geometry. You can also print black and white images of undeformed and deformed
shape plots. When you choose Black&White, ABAQUS/CAE always prints a black image on
a white background, and the viewport background is printed as either transparent or white.
This option should not be used for printing images that depend heavily on color, such as
contour plots.
Grayscale
Use this option to print grayscale versions of color images, where each color is approximated
by a shade of gray. (ABAQUS/CAE converts each color to one of 256 true shades of gray.)
This option is useful for printing color images, such as contour plots, to a black and white
laser printer. To improve the appearance of images sent to a printer, you may want to print
viewports with the background turned off (so that it appears white or transparent).
Color
Use this option to print an approximation of the colors you see. ( ABAQUS/CAE uses up to
256 different colors, both on the screen and in your printed image.) This option is useful for
printing images such as contour plots to a color printer or to a file that will ultimately be
displayed online. If you try to print a color image to a black and white PostScript printer, the
printer converts the colors to shades of gray.
7-267
Printing canvas objects
2. From the Rendition menu button in the Settings field, select one of the following color options:
3. When you have finished with the Print dialog box, click OK to generate the desired output.
ABAQUS/CAE generates the output and closes the Print dialog box. Your settings in the Print
dialog box are saved for the duration of the session.
· ``Controlling the destination and appearance of printed images, '' Section 11.2
PostScript
Select PostScript (PS) if you want the saved image to be identical to the image that
ABAQUS/CAE would print to a PostScript printer. Additional options for this format allow
you to choose the paper size, orientation, margins, and resolution of your image, and whether
or not to include the date and ABAQUS logo. For more information, see ``Customizing the
image sent to a PostScript printer or file,'' Section 11.2.5.
Encapsulated PostScript
Select Encapsulated Postscript ( EPS) if you want to incorporate the saved image in a separate
document; for example, a word processing file. Additional options for this format allow you to
7-268
Printing canvas objects
specify the size and resolution of the image. For more information, see ``Customizing the
image saved in an Encapsulated PostScript file,'' Section 11.2.6.
TIFF
Select TIFF if you want to incorporate the saved image in a separate document; for example, a
word processing file. Additional options for this format allow you to specify the size of the
image. For more information, see ``Customizing the image saved in TIFF or PNG files,''
Section 11.2.7.
PNG
Select PNG if you want to incorporate the saved image in a separate document; for example,
an HTML file for display on the World Wide Web. Additional options for this format allow
you to specify the size of the image. For more information, see ``Customizing the image saved
in TIFF or PNG files,'' Section 11.2.7.
2. From the Destination buttons in the Settings field, select one of the following:
Printer
Choose Printer to send your PostScript image to a printer, and type the print command in
the Print command text field. This command should be the same command that you
would use at your workstation to print a PostScript file. Do not include a file name in the
print command; ABAQUS/CAE automatically appends the file name to your command.
See your systems administrator for details on the valid commands at your site.
Click the arrows in the Copies field to set the desired number of copies to print, or type
the number of copies you want into the text field. You can print up to 100 copies. If
desired, click PS Options to specify the page size, printed image resolution, and other
options.
File
Choose File to send your image to a file. There are two ways to supply the file name:
File name
Type the name in the File name text field. You can type any characters that are
legal UNIX or Windows NT file names; for example, on a UNIX system:
stressfield.png
../../nozzle/presentation/injector_mesh
~/pump/actuator/strainpattern.eps
7-269
Printing canvas objects
Use the Select button to supply a file name using the standard file browser. For
more information on file selection, see ``Using file selection dialog boxes,''
Section 6.3.7.
3. If you selected to print the image to a file, click the Format menu button to select either a
PostScript (PS), Encapsulated PostScript (EPS), TIFF, or PNG format file. If desired, click the
respective options button to specify additional options.
4. When you have finished with the Print dialog box, click OK to generate the desired output.
ABAQUS/CAE generates the output and closes the Print dialog box. Your settings in the Print
dialog box are saved for the duration of the session.
· ``Controlling the destination and appearance of printed images, '' Section 11.2
Paper Size
You can choose from a list of standard page sizes.
Orientation
You can choose either Portrait or Landscape orientation. Portrait and landscape orientations
are illustrated in the following figure:
7-270
Printing canvas objects
Margins
You can provide the Top, Bottom, Left, and Right margins. ABAQUS/CAE computes the
maximum image size as the page size minus the margins. You can specify zero-width margins;
however, printers cannot print to the edge of the paper and typically have margins of at least
0.25 inches (8 mm). ABAQUS/CAE maintains the margins you specify regardless of the
orientation of the paper. For example, assume you chose a Portrait image and entered a value
for the Top margin. If you now choose a Landscape image, ABAQUS/CAE uses the value
you entered for the Top margin to compute the Left margin. Similarly, the value you entered
for the Right margin becomes the Top margin.
Text Rendering
You can specify how you want text on the canvas to appear in the printed image. You can use
either PostScript fonts or request that text characters be output as small bitmaps.
If you select Always use PostScript printer fonts, ABAQUS/CAE prints only font families
that are commonly available on a postscript printer (Courier, Helvetica, Times, and Symbol.)
Any other font is replaced by Courier, the default font.
If you select Use PostScript printer fonts when available , ABAQUS/CAE prints any
canvas text that appears in Courier, Helvetica, Times, or Symbol font. However, text in any
other font is output as small bitmaps for each character. This option requires more processing
and results in a larger PostScript file. No fonts are replaced by the default font.
If you select Always use displayed fonts (WYSIWYG), all characters are output as small
bitmaps.
Resolution
You can select from a list of standard resolutions. The resolution setting will be used only to
generate bitmap representation PostScript images. (For more information, see ``Printed image
formats,'' Section 11.1.1.) The maximum effective resolution of a bitmap PostScript image is
limited to the resolution of the device on which the image will be displayed. By default,
ABAQUS/CAE sets the resolution of a bitmap PostScript image to 150 dpi. To save disk
space, you should select the minimum acceptable resolution.
7-271
Printing canvas objects
output.
If you are printing to a printer, the Print dialog box also allows you to type a printer command and set
the number of copies to print.
For more information, see ``PostScript image size and layout,'' Section 11.1.2 and ``Hardcopy image
quality,'' Section 11.1.4.
To customize the image sent to a printer:
4. Click the arrows to the right of the Copies text field to increase or decrease the number of copies
to print or type the number directly in the text field. You can print 1 to 100 copies.
5. From the lower-right corner of the Print dialog box, click PS Options.
The PostScript Options dialog box appears.
8. From the Margins field, type the Top, Bottom, Left, and Right margins in inches.
9. From the Resolution menu button, select from the list of resolutions.
10. If desired, toggle off Print date to remove the date and time from your output.
11. If desired, toggle off Print ABAQUS logo to remove the logo from your output.
12. Click OK to save your PostScript customization settings and to close the PostScript Options
dialog box.
13. When you have finished with the Print dialog box, click OK to generate the desired output.
ABAQUS/CAE generates the output and closes the Print dialog box. Your settings in the Print
dialog box are saved for the duration of the session.
7-272
Printing canvas objects
· ``Controlling the destination and appearance of printed images, '' Section 11.2
Image Size
You can save an image that is the same size as the image on the screen, or you can specify the
size of the image in inches or millimeters. You specify either the width or the height;
ABAQUS/CAE calculates the other dimension to maintain the aspect ratio of the canvas
objects.
Text Rendering
You can specify how you want text on the canvas to appear in the printed image. You can use
either PostScript fonts or request that text characters be output as small bitmaps.
If you select Always use PostScript printer fonts, ABAQUS/CAE prints only font families
that are commonly available on a postscript printer (Courier, Helvetica, Times, and Symbol.)
Any other font is replaced by Courier, the default font.
If you select Use PostScript printer fonts when available , ABAQUS/CAE prints any
canvas text that appears in Courier, Helvetica, Times, or Symbol font. However, text in any
other font is output as small bitmaps for each character. This option requires more processing
and results in a larger PostScript file. No fonts are replaced by the default font.
If you select Always use displayed fonts (WYSIWYG), all characters are output as small
bitmaps.
Resolution
You can select from a list of standard resolutions. The resolution setting will be used only to
generate bitmap representation EPS images. (For more information, see ``Printed image
formats,'' Section 11.1.1.) The maximum effective resolution of a bitmap representation EPS
image is limited to the resolution of the device on which the image will be displayed. By
default, ABAQUS/CAE sets the resolution of a bitmap EPS image to 150 dpi. To save disk
space, you should select the minimum acceptable resolution. For more information, see
``Hardcopy image quality,'' Section 11.1.4.
7-273
Printing canvas objects
3. In the File name text field, type the file name or click Select to select the file name from the
standard file browser.
5. From the lower-right corner of the Print dialog box, click EPS Options.
The Encapsulated PostScript Options dialog box appears.
· Choose Use size on screen to save an EPS image that is the same size as the overall width
and height of the canvas objects that you select for printing. ABAQUS/CAE displays the
resulting size to the right of the Use size on screen radio button.
· Choose Use settings below to specify the width or height of the resulting image in either
inches or millimeters.
7. From the Resolution menu button, select from the list of resolutions.
8. Click OK to save your customization settings and to close the Encapsulated PostScript Options
dialog box.
9. When you have finished with the Print dialog box, click OK to generate the desired output.
ABAQUS/CAE generates the output and closes the Print dialog box. Your settings in the Print
dialog box are saved for the duration of the session.
· ``Controlling the destination and appearance of printed images, '' Section 11.2
7-274
Printing canvas objects
2. In the File name text field, type the file name or click Select to select the file name from the
standard file browser.
5. From the lower-right corner of the Print dialog box, click TIFF Options or PNG Options.
The appropriate dialog box appears.
· Choose Use size on screen to save an image that is the same size as the overall width and
height of the canvas objects that you select for printing. ABAQUS/CAE displays the resulting
size to the right of the Use size on screen radio button.
· Choose Use settings below to specify the width or height of the resulting image in units of
pixels. The maximum image size allowed is 1280 ´ 1024 pixels.
7. Click OK to save your customization settings and to close the dialog box.
8. When you have finished with the Print dialog box, click OK to generate the desired output.
ABAQUS/CAE generates the output and closes the Print dialog box. Your settings in the Print
dialog box are saved for the duration of the session.
· ``Controlling the destination and appearance of printed images, '' Section 11.2
7-275
Working with ABAQUS/CAE model databases , models , and files
· Chapter 12, "Understanding and working with ABAQUS/CAE models, model databases, and files"
0-276
Understanding and working with ABAQUS/CAE models , model databases , and files
· ``Understanding the files generated by creating and analyzing a model,'' Section 12.3
Figure 12-1 ABAQUS/CAE displays the model database name and the model name.
1-277
Understanding and working with ABAQUS/CAE models , model databases , and files
When you first start ABAQUS/CAE, the Start Session dialog box allows you to either create a new,
empty model database or to open an existing model database. Anything you create or define in
ABAQUS/CAE is stored in this model database. You save the contents by selecting File->Save or
File->Save As from the main menu bar.
ABAQUS/CAE never saves the model database unless you perform an explicit save operation; there is
no timer-based automatic saving, for example. However, while you work on your model,
ABAQUS/CAE maintains a record of all the operations that changed the model database. Although
you may not have saved the model database, you can always replay the operations that replicate its
current state. For more information on recreating the model database, see ``Recreating an unsaved
model database,'' Section 12.4.3.
After you begin an ABAQUS/CAE session, you can open an existing model database by selecting
File->Open from the main bar, or you can create a new model database by selecting File->New . If you
open or create another model database after you have made changes to the current one, ABAQUS/CAE
asks if you want to save the changes before it closes the current model database.
· Chapter 12, "Understanding and working with ABAQUS/CAE models, model databases, and files
· parts
· assembly information
· steps
1-278
Understanding and working with ABAQUS/CAE models , model databases , and files
· meshes
A model database can contain any number of models so that you can keep all models related to a single
problem in one database. (For more information, see ``What is an ABAQUS/CAE model database?,''
Section 12.1.) You can open multiple models from the model database at the same time, and you can
work on different models in different viewports. The viewport title bar (if visible) displays the name of
the model associated with the viewport. The model associated with the current viewport (indicated by
a red border) is called the current model, and there is only one current model. Figure 12-1 shows two
viewports displaying two different models (high_speed and low_speed) in the same model
database (crankshaft.cae); the current viewport in Figure 12-1 is displaying the high_speed
model.
You use the Model Manager or the Model menu items from the main menu bar to create and manage
your models. You use the Model list located under the toolbar to switch to a different model in the
current model database.
You can create a copy of a model within a model database; in addition, you can copy the following
objects between models:
· Sketches
· Materials
· Sections
· Amplitudes
However, you cannot copy a model from one model database to another. For detailed instructions, see
``Manipulating models within a model database,'' Section 12.7.1, and ``Copying objects between
models,'' Section 12.7.3.
ABAQUS/CAE checks that your model is complete when you submit it for analysis. For example, if
you request a dynamic analysis, you must specify the density of the materials so that the mass and
inertia properties of the model can be calculated. If you did not provide a material density in the
Property module, the Job module reports an error; for more information, see ``Monitoring the progress
of an analysis job,'' Section 21.2.6.
In some modules ABAQUS/CAE does not support functionality from ABAQUS/Standard or
ABAQUS/Explicit that you may want to include in the analysis. You may be able to add such
functionality by using the Keywords Editor to edit the ABAQUS/Standard and ABAQUS/Explicit
keywords associated with a model. Select Model->Edit Keywords->model name from the main menu
bar to start the Keywords Editor. (You can review the keywords supported by ABAQUS/CAE by
selecting Help->Keyword Browser from the main menu bar.)
1-279
Understanding and working with ABAQUS/CAE models , model databases , and files
· Chapter 12, "Understanding and working with ABAQUS/CAE models, model databases, and files
When you select File->Save from the main menu bar and save the model database, ABAQUS/CAE
saves the following files:
When you continue to work on your model, ABAQUS/CAE continues to record your actions in the
replay file. In addition, ABAQUS/CAE saves the following file:
When you submit a job for analysis, ABAQUS/Standard and ABAQUS/Explicit create a set of files;
for a complete list of these files, see ``File extensions used by ABAQUS,'' Section 3.5.1 of the
ABAQUS/Standard User's Manual and the ABAQUS/Explicit User's Manual. The following list
describes some of the files that ABAQUS/Standard and ABAQUS/Explicit create and their
relationship to ABAQUS/CAE:
1-280
Understanding and working with ABAQUS/CAE models , model databases , and files
Note: The errors and warnings that ABAQUS/Standard and ABAQUS/Explicit write to the data,
message, and status files while analyzing a job can be monitored by the Job module; for more
information, see ``Monitoring the progress of an analysis job,'' Section 21.2.6.
1-281
Understanding and working with ABAQUS/CAE models , model databases , and files
1-282
Understanding and working with ABAQUS/CAE models , model databases , and files
option executes the commands in the specified model database journal file.
The model database journal file differs from the replay file in that it does not contain every operation
performed during a session. The model database journal file contains only the commands that change
the saved model database; for example, commands that create or edit a part, change the time
incrementation of an analysis step, or modify the mesh. Operations that do not change the model
database are not saved in the journal file; for example, sending an image to a printer, creating a
viewport, rotating the model, or viewing results in the Visualization module.
As you continue to work on your model, the model database in memory will differ from the most
recently saved model database. The model database journal file is updated only when you perform an
explicit save of the model database using File->Save or File->Save As. If you copy the model
database to a different location, you should also copy the associated model database journal file.
Otherwise, you will not be able to recreate the model database.
1-283
Understanding and working with ABAQUS/CAE models , model databases , and files
you might write a script that defines the material properties of a commonly used material. The replay
file, the model database journal file, and the model database recovery file all contain ABAQUS/CAE
commands. ABAQUS/CAE commands are written in the Python scripting language, and you can use
Python to enhance the scripts generated by ABAQUS/CAE. For more information on ABAQUS/CAE
commands, see the ABAQUS Scripting Interface Manual.
Commands are stored as ASCII text in the replay, journal, and recovery files and in ABAQUS/CAE
scripts that you create. As a result, you can use a standard text editor to edit the contents of the files.
For more information on commands, see the ABAQUS Scripting Interface Manual.
To run a script, select File->Run Script from the main menu bar, and select the script to run from the
Run Script dialog box.
Note: You should use the recover option from the ABAQUS/CAE execution procedure to run a
journal file and recreate a saved model database. (Type abaqus cae
recover=model_database_name.jnl.) Selecting File->Run Script to run a journal file
may result in an incomplete model database.
· Select File->New to create a new model database. You can also click in the toolbar. For more
information, see ``Creating a new model database,'' Section 12.6.1.
1-284
Understanding and working with ABAQUS/CAE models , model databases , and files
· Select File->Open to open an existing model database or output database. You can also click
in the toolbar. For more information, see ``Opening a model database or an output database, ''
Section 12.6.2.
· Select File->Close ODB to close an output database. For more information, see ``Closing the
current output database,'' Section 12.6.3.
· Select File->Save to save the current model database. You can also click in the toolbar. For
more information, see ``Saving the current model database,'' Section 12.6.4.
· Select File->Save As to save the current model database with a new name. For more information,
see ``Saving the current model database with a new name,'' Section 12.6.5.
For more information, see ``Exporting a part to an ACIS-, IGES-, or VDA-FS-format file,'' Section
13.7.2.
1-285
Understanding and working with ABAQUS/CAE models , model databases , and files
For more information, see ``Exporting a part to an ACIS-, IGES-, or VDA-FS-format file,'' Section
13.7.2.
For more information, see ``Exporting the assembly to an ACIS-format file,'' Section 13.7.3.
· Select File->Macro Manager to store your actions in a macro file as a sequence of ABAQUS/CAE
commands. You can also run a run a macro and rename an existing macro.
· Select File->Print to print all or selected viewports and annotations. You can also click in the
toolbar. For more information, see Chapter 11, "Printing canvas objects."
· Select File->Exit to exit the ABAQUS/CAE session. For more information, see ``Exiting an
ABAQUS/CAE session,'' Section 5.1.2.
· ``Understanding the files generated by creating and analyzing a model,'' Section 12.3
· ``Saving the current model database with a new name,'' Section 12.6.5
1-286
Understanding and working with ABAQUS/CAE models , model databases , and files
· ``Understanding the files generated by creating and analyzing a model,'' Section 12.3
From the Open Database dialog box that appears, select the File Type and the file to open and click
OK.
To specify the directory that should be searched by default when you open a model database or an
output database and which files should be displayed in the Open Database dialog box, you can
include lines similar to the following in your ABAQUS resource file (Abaqus).
On UNIX systems
*FileOpenDB.dialog*pattern: /usr/smith/my_models/*.cae
*FileOpenDB.dialog*pattern: /usr/smith/my_output/*.odb
On Windows NT systems
*FileOpenDB.dialog*pattern: c:\users\smith\my_models\*.cae
*FileOpenDB.dialog*pattern: c:\users\smith\my_output\*.odb
For more information on the ABAQUS resource file, see ``Customizing X resources,'' Section 6.1.
Detailed instructions for opening a model database or an output database:
1-287
Understanding and working with ABAQUS/CAE models , model databases , and files
Tip: You can also click in the toolbar to open a model database or an output database.
2. From the File Type menu at the top of the Open Database dialog box, select one of the
following:
Model Database (*.cae)
ABAQUS/CAE lists all the files in the selected directory with the file extension .cae.
Select the model database to open, and click OK.
ABAQUS/CAE opens the model database and displays its name in the title bar of the main
window. All operations now refer to the new model database. If you have modified the
current model database, ABAQUS/CAE asks if you want to save it before it opens the
selected model database.
Output Database (*.odb)
ABAQUS/CAE lists all the files in the selected directory with the file extension .odb.
Select the output database to open, and click OK.
ABAQUS/CAE starts the the Visualization module in the current viewport and displays
the model in fast mode. You can open more than one output database at the same time and
display the contents in different viewports.
For more information on specifying the file to open, see ``Using file selection dialog boxes,''
Section 6.3.7.
1-288
Understanding and working with ABAQUS/CAE models , model databases , and files
2. Select the output database to close and click OK to close the dialog box.
ABAQUS/CAE closes the selected output database and clears any viewports that were displaying
data from that output database.
· ``Understanding the files generated by creating and analyzing a model,'' Section 12.3
Select File->Save from the main menu bar or click in the toolbar to save the current model
database. After you save the model database, ABAQUS/CAE displays its name in the title bar of the
main window.
Before you save the current model database for the first time, it exists only in memory and has no
name. When you save the current model database for the first time, ABAQUS/CAE displays the Save
Model Database As dialog box to allow you to enter a name; subsequent saves use this name. If you
omit the file extension, ABAQUS/CAE appends .cae to the file name.
For information on saving the model database using a different name and on customizing the default
behavior of the Save Model Database As dialog box, see ``Saving the current model database with a
new name,'' Section 12.6.5. For more information on saving files, see ``Using file selection dialog
boxes,'' Section 6.3.7.
You should save the model database periodically. ABAQUS/CAE never saves the model database
unless you perform an explicit save operation; there is no timer-based automatic saving, for example. If
you try to save a model database that has not been modified, no action is taken.
ABAQUS/CAE asks you if you want to save a modified model database before you exit the session.
1-289
Understanding and working with ABAQUS/CAE models , model databases , and files
On UNIX systems
*saveMdbDB.dialog*pattern: /usr/smith/my_models/*.cae
*saveMdbDB.dialog*pattern: /usr/smith/my_output/*.odb
On Windows NT systems
*saveMdbDB.dialog*pattern: c:\users\smith\my_models\*.cae
*saveMdbDB.dialog*pattern: c:\users\smith\my_output\*.odb
For more information on the ABAQUS resource file, see ``Customizing X resources,'' Section 6.1.
Note: You cannot save a model database using the name abaqus.
1-290
Understanding and working with ABAQUS/CAE models , model databases , and files
For general information on managing objects, see ``Managing objects,'' Section 6.5, and ``Managing
objects using manager menus,'' Section 6.5.7.
To create a new model, select Model->Create from the main menu bar and enter the name of the
model in the Create Model dialog box that appears.
To open a model and associate it with the current viewport, select the desired model from the Model
list under the toolbar. The Model list contains all the models in the current model database.
To copy, rename, or delete models, select the Copy, Rename, or Delete items listed under the Model
menu on the main menu bar. The Copy, Rename, and Delete items contain submenus listing all the
models in the current model database. For general information on how to use these menus, see
``Managing objects using manager menus,'' Section 6.5.7.
You can also create, copy, rename, and delete models using the Model Manager. To display the Model
Manager, select Model->Manager from the main menu bar. The Model Manager dialog box contains
functions identical to those listed under the Model menu but with a convenient browser that lists all
the models available in the current model database. For general information on how to use managers,
see ``Managing objects,'' Section 6.5.
You can copy a model to a new model in a model database. In addition, you can copy sketches, parts,
materials, sections, and amplitudes between the models in a model database.; for more information, see
``Copying objects between models,'' Section 12.7.3. However, you cannot copy models between model
databases.
1-291
Understanding and working with ABAQUS/CAE models , model databases , and files
· Sketches
· Materials
· Sections
· Amplitudes
You cannot copy other individual objects, such as the assembly, loads, or steps; however, you can
achieve a similar effect by copying the entire model to a new model and editing the objects in the new
model. For more information, see ``Manipulating models within a model database,'' Section 12.7.1.
Dependent objects are not copied automatically when you copy an object between models. For
example, if you copy a section, the associated material is not copied along with the section; you must
copy the material in a separate copy operation.
Detailed instructions for copying objects between models:
2. From the dialog box, select the model to copy objects from.
3. Use the following techniques to specify the objects to copy from the selected model:
1-292
Understanding and working with ABAQUS/CAE models , model databases , and files
· Click the arrow next to the desired object category. From the list of objects that appears,
toggle the names of the objects of your choice. An object category is unavailable if it contains
no objects.
· Toggle the desired object category. This action selects or deselects all objects within that
category.
The check box next to an object category becomes completely filled when all objects within that
category are selected. The box becomes half filled if only some of the objects within that category
are selected. You must select at least one object or object category to copy.
4. From the bottom of the Copy Model Objects dialog box, select the model to copy the selected
objects to.
5. Click OK to copy the selected objects and to close the Copy Model Objects dialog box.
ABAQUS/CAE copies the selected objects. If an object with the same name already exists in the
model to which you are copying the object, ABAQUS/CAE asks for confirmation that you want to
overwrite the existing object. Click Yes to All to overwrite all existing objects with the same name
as the objects you are copying.
· In the Description field, type information that you want to record about the model.
· In the area of the dialog box labeled Physical Constants, enter values for absolute zero and
the Stefan-Boltzmann constant.
1-293
Understanding and working with ABAQUS/CAE models , model databases , and files
1-294
Understanding and working with ABAQUS/CAE models , model databases , and files
statements.
You can review the keywords supported by ABAQUS/CAE by selecting Help->Keyword Browser
from the main menu bar.
Detailed instructions for editing the model's keywords:
2. Each keyword in the input file is displayed in its own block. Buttons in the lower left corner of the
Keywords Editor allow you to do the following:
Add After
Add an empty block of text below the selected block. A blue vertical bar indicates a block
that you added.
Remove
Remove the selected block of text that was added using the Keywords Editor. You
cannot remove a block generated by ABAQUS/CAE.
Discard Changes
Discard the changes you made to a block generated by ABAQUS/CAE during the most
recent use of the Keywords Editor.
In addition, you can click any block and edit the text inside. A red vertical bar indicates a block
generated by ABAQUS/CAE that you edited.
3. From the buttons across the bottom of the Keywords Editor, click OK to include your changes
and to close the editor. Click Cancel to disregard your changes.
1-295
Understanding and working with ABAQUS/CAE models , model databases , and files
sequence of interactions.
The macro file is called abaqusMacros.py and is saved in your local directory. The Macro
Manager contains a list of the existing macros that ABAQUS/CAE detected in the
abaqusMacros.py file. You can copy or rename abaqusMacros.py; however, the new file will
not be recognized by the Macro Manager.
Your macro will run only in the same context in which it was recorded. For example, if you create a
macro while in the Part module that copies a part named gear1 to a new part named gear2 and exit
ABAQUS/CAE, the macro will be executed in a new ABAQUS/CAE session only if you enter the Part
module and a part named gear1 exists.
The ABAQUS Scripting Interface commands are stored in ASCII text, and you can edit
abaqusMacros.py with a standard text editor. For more information on commands, see the
ABAQUS Scripting Interface Manual.
Detailed instructions for creating a macro:
2. From the buttons across the bottom of the Macro Manager dialog box, click Create.
3. Enter a name for the macro in the Create Macro dialog box that appears, and click Continue. You
cannot overwrite an existing macro.
Each of your interactions with ABAQUS/CAE is stored as a command in the
abaqusMacros.py file. A Recording macro dialog box appears to remind you the macro is
recording. In addition, the Create, Delete, and Run buttons are not available in the Macro
Manager while the macro is recording.
2. Select the macro to delete. You can select more than one macro.
3. From the buttons across the bottom of the Macro Manager dialog box, click Delete.
4. From the dialog box that appears, click OK to confirm your action.
ABAQUS/CAE deletes the macro from abaqusMacros.py. You cannot recover a deleted
macro.
1-296
Understanding and working with ABAQUS/CAE models , model databases , and files
3. From the buttons across the bottom of the Macro Manager dialog box, click Run. You can run
only one macro; the Run button is not available if you selected more than one macro.
ABAQUS/CAE runs the commands in the selected macro and displays a message in the message
area when the macro execution completes.
1-297
Importing and exporting geometry data and models
· ``What kinds of files can be imported and exported from ABAQUS/CAE?,'' Section 13.1
· ``Importing models from ABAQUS/Standard and ABAQUS/Explicit input files,'' Section 13.4
ACIS (file_name.sat)
ACIS is an object-oriented toolkit designed for use as a geometry engine for modeling
applications and is considered the industry standard for geometry modeling. You can import
ACIS-format parts, and you can export parts or the assembly in ACIS format. In addition, you
can import and export a sketch from an ACIS file. For more information, see ``Importing
sketches,'' Section 13.5.1; ``Importing parts,'' Section 13.5.2; and ``Exporting geometry data,''
Section 13.7.
IGES (file_name.igs)
The Initial Graphics Exchange Specification (IGES) is a neutral data format designed for
graphics exchange between computer-aided design (CAD) systems. You can import
IGES-format parts, and you can export parts in IGES format. In addition, you can import and
export a sketch from an IGES file. For more information, see ``Importing sketches,'' Section
13.5.1; ``Importing parts,'' Section 13.5.2; and ``Exporting geometry data,'' Section 13.7.
VDA-FS (file_name.vda)
The Verband der Automobilindustrie (VDA) surface data format is a geometry standard
developed by the German automotive industry. Both VDA-FS and IGES files contain a
mathematical representation of the part in an ASCII format; however, the VDA-FS standard
concentrates on geometry information. Additional information covered by the IGES standard,
2-298
Importing and exporting geometry data and models
such as dimensions, text, and colors, is not stored in a VDA-FS file. As a result, the file format
is simplified, and you may find it easier to transfer files between CAD systems and
ABAQUS/CAE using VDA-FS files.
You can import VDA-FS-format parts, and you can export parts in VDA-FS-format. For more
information, see ``Importing parts,'' Section 13.5.2; and ``Exporting geometry data,'' Section
13.7.
AutoCAD (file_name.dxf)
Two-dimensional profiles stored in AutoCAD (.dxf) files can be imported as stand-alone
sketches. For more information and details of the AutoCAD entities supported by
ABAQUS/CAE, see ``Importing sketches,'' Section 13.5.1.
· Replace the mesh of the current orphan mesh part with the imported orphan mesh. All
current sets are deleted, and sets from the imported orphan mesh are imported into the
current part. The name of the current part does not change; and, if the set names in the
imported database are the same as the current set names, the part will maintain all
set-based assignments.
· Chapter 12, "Understanding and working with ABAQUS/CAE models, model databases, and files
2-299
Importing and exporting geometry data and models
For a complete list of the IGES entities that can be imported into ABAQUS/CAE, see ``IGES entities
recognized by ABAQUS/CAE when importing a part or a sketch,'' Section 13.5.5.
Some of the IGES entities are stored as a set of parametric surfaces along with a set of trim curves that
delineate the boundaries of the surfaces. ABAQUS/CAE allows you to choose how these trim curves
are defined:
An IGES file can contain curves defined using real space, parameter space, or both. When you import a
part from an IGES file into ABAQUS/CAE, the surface and the trim curves are converted into an
internal representation of the part. By default, ABAQUS/CAE uses the information stored in the
IGES-file to decide how the trim curve is defined; alternatively, you can force ABAQUS/CAE to
always use either real space or parameter space.
CAD applications store data in IGES-format files using their own interpretation of the IGES standard.
ABAQUS/CAE is able to interpret IGES-format files generated by most applications. In addition,
when you export a part or the assembly to an IGES-format file, ABAQUS/CAE allows you to specify
the application that will be reading the file, and the data are written out in the appropriate tailored
format or flavor. You can choose one of the following flavors:
2-300
Importing and exporting geometry data and models
· Standard
· AutoCAD
· SolidWorks
ABAQUS/CAE stores the geometry of a part to an accuracy of 10-6 units; however, different
applications may use a lower precision. As a result, during the import process ABAQUS/CAE may
detect problems with face trimming curves that appear to be disconnected or separated from the
underlying surface. Figure 13-1 illustrates an imported part. Because of precision limitations, vertex A
appears to be separated from vertex B; similarly, trim curve A appears to be separated from trim curve
B.
2-301
Importing and exporting geometry data and models
When you import a part, ABAQUS/CAE displays a dialog box that allows you to repair the part. Parts
created by ABAQUS/CAE are composed of geometry that is always considered to be valid and precise.
Conversely, a part imported from another application can be invalid or imprecise and should be
repaired. Invalid and imprecise parts are described in the following list:
Invalid
If the part is invalid, you can use the automated geometry repair tool to try and make it valid.
If the part still cannot be made valid, you cannot modify it in the Part module or mesh it in the
Mesh module. In addition, it cannot be analyzed by either ABAQUS/Standard or
ABAQUS/Explicit. In general, a part that cannot be made valid cannot be used by
ABAQUS/CAE. You must return to the CAD application that generated the original file and
attempt to fix the geometry.
Imprecise
A valid part can be either precise or imprecise. If the part is imprecise, you can use the
geometry repair tools to try and make it precise. If the part still cannot be made precise, it can
still be used by ABAQUS/CAE; however, some functionality will be disabled. You should
return to the CAD application that generated the original file and increase the precision.
ABAQUS/CAE can perform the following set of operations in an effort to repair the geometry of an
imported part.
Some of the operations are dependent on each other. For example, if you stitch the edges of a part, you
must also convert it to an analytical representation. Similarly, if you convert the part to a more precise
representation, you must also stitch its edges and convert it to an analytical representation.
2-302
Importing and exporting geometry data and models
You can repair a part during the import process. Alternatively, you can repair a part after importing it
by selecting Part->Repair Geomety from the main menu bar. The Part module provides a more
complete set of geometry repair tools that allows you to repair and edit imported and ABAQUS/CAE
native parts; for more information, see ``Repairing and editing imported parts,'' Section 14.5.3.
· Amplitudes
See ``Keyword support from the input file reader,'' Section A.2 for a complete list of the keywords that
are supported by the input file reader.
You can import models with a mixture of rigid and deformable parts. The input file reader uses
element definitions to create separate deformable parts and analytical and discrete rigid parts. All of
the deformable elements in the input file form a single deformable part in ABAQUS/CAE. However, a
separate rigid part is created for each *RIGID BODY, *RIGID SURFACE, and *SURFACE option
that is encountered. The rigid body reference nodes are assigned according to the REF NODE
parameter on the *RIGID BODY and *RIGID SURFACE options. Deformable and rigid parts created
by the import capability are stored in the form of an orphan mesh; an orphan mesh comprises node and
element definitions and the type of element assigned. An orphan mesh part consists of a single feature;
you can use the mesh edit tools to modify an orphan mesh, but you cannot add geometric features to
it.
The import capability creates sets based on any *ELSET or *NSET keywords, as well as any ELSET or
NSET parameters on other supported keywords. If the nodes or elements in a set appear on only a
single part (deformable or rigid), ABAQUS/CAE creates both a part set and an assembly set. Similarly,
2-303
Importing and exporting geometry data and models
if these nodes or elements appear on separate parts, ABAQUS/CAE creates an assembly set and
multiple part sets. Each part set contains only the nodes or elements from the imported set that appear
on the particular part.
Most of the commonly used element types can be assigned to the elements in an orphan mesh.
However, some element types cannot be imported from an input file. For a full list of unsupported
elements and detailed instructions on using the input file reader, see ``Using the input file reader to
import a model,'' Section 13.6.
You can use the Mesh module to change the element type assigned to an orphan mesh imported from
an input file. In addition, you can use the Keywords Editor to include options that the input file reader
does not support; for detailed instructions on using the Keywords Editor, see ``Adding unsupported
keywords to your ABAQUS/CAE model,'' Section 12.8.
· ``IGES entities recognized by ABAQUS/CAE when importing a part or a sketch,'' Section 13.5.5
If you are importing a sketch, the file must contain a two-dimensional planar profile that can be
mapped directly to the sketch plane. If the file contains three-dimensional geometry, ABAQUS/CAE
does the following:
· If you are importing an AutoCAD file, ABAQUS/CAE creates the sketch using the geometry in the
2-304
Importing and exporting geometry data and models
· If you are importing an IGES or ACIS file, ABAQUS/CAE displays an error message and cancels
the import procedure.
You can import sketches from files that contain only simple geometry because ABAQUS/CAE must be
able to translate the geometry to a corresponding Sketcher entity, such as a line, circle, arc, or spline. If
ABAQUS/CAE finds geometry it cannot translate, it ignores that geometry. For a list of the IGES and
AutoCAD entities supported by ABAQUS/CAE, see ``Imported sketches,'' Section 22.3.2.
Detailed instructions for importing a sketch:
2. From the File Type menu at the top of the Import Part dialog box, select one of the following:
· IGES (*.igs)
· ACIS (*.sat)
3. Select the file containing the sketch to import and click OK.
ABAQUS/CAE enters the Sketch module, converts the profile in the file to a sketch, and exits the
Sketch module. The sketch now appears in the list of sketches in the model and can be retrieved
when you enter the Sketch module. For information on how to use the imported sketch, see
``Stand-alone sketches,'' Section 22.3.1.
2-305
Importing and exporting geometry data and models
An output database
You can import the assembly stored in an output database in the form of an orphan mesh. An
orphan mesh part contains no feature information and is extracted from the output database as
a collection of nodes, elements, surfaces, and sets. You can use the Part module to edit the
nodes and elements that form the orphan mesh. Although the model that was analyzed may
have been constructed from multiple part instances, only one orphan mesh part can be
extracted from the resulting output database.
For more information, see ``Importing a part from an output database,'' Section 13.5.7.
2. From the File Type menu at the top of the Import Part dialog box, select one of the following:
· IGES (*.igs); for more information, see ``Importing a part from an IGES-format file,'' Section
13.5.4.
· VDA-FS (*.vda); for more information, see ``Importing a part from a VDA-FS format file,''
Section 13.5.6.
· ACIS (*.sat); for more information, see ``Importing parts from an ACIS-format file,'' Section
13.5.3.
· Output Database (*.odb); for more information, see ``Importing a part from an output
database,'' Section 13.5.7.
3. ABAQUS/CAE lists all the files in the selected directory with the appropriate file extension. Select
the file containing the part to import, and click Continue.
ABAQUS/CAE enters the Part module, the imported part replaces the contents of the current
viewport, and the part appears in the model's list of parts below the toolbar.
2-306
Importing and exporting geometry data and models
2. From the File Type menu at the top of the Import Part dialog box, select ACIS (*.sat).
ABAQUS/CAE lists all the files in the selected directory with a .sat file extension.
3. Select the ACIS file containing the part or parts to import, and click Continue.
The Create Part from ACIS File dialog box appears.
4. ABAQUS/CAE uses the name of the file to name the part and assumes that the part type is
deformable; you can change the part's name and type if desired. ABAQUS/CAE tries to determine
the modeling space as follows:
· If ABAQUS/CAE determines the part is planar, you can choose whether the modeling space is
2-307
Importing and exporting geometry data and models
two- or three-dimensional.
· If ABAQUS/CAE determines the part is planar and that its geometry does not cross the Y-axis,
you can choose whether the modeling space is axisymmetric, two-dimensional, or
three-dimensional. If you choose axisymmetric, the Y-axis is assumed to be the axis of
revolution, and you can add a twist degree of freedom.
5. If desired, click the Repair Options tab and toggle the desired repair operations. For more
information, see ``Repairing an imported part,'' Section 13.5.8.
2-308
Importing and exporting geometry data and models
2. From the File Type menu at the top of the Import Part dialog box, select IGES (*.igs).
ABAQUS/CAE lists all the files in the selected directory with a .igs file extension.
3. Select the IGES file containing the part to import, and click Continue.
ABAQUS/CAE displays the Import from IGES dialog box containing header information from the
IGES file.
4. If desired, click IGES Options to open the IGES Options dialog box and to view a list of the
entities read from the IGES-format file. The list includes a description of the entity along with its
entity number, the number of occurrences found in the IGES file, and whether it is supported by
ABAQUS/CAE. For a complete list of the IGES entities that can be imported into ABAQUS/CAE,
see ``IGES entities recognized by ABAQUS/CAE when importing a part or a sketch,'' Section
13.5.5.
5. If desired, use the IGES Options dialog box to customize the following:
· How ABAQUS/CAE converts the surface and the trim curves into an internal representation
of the part. By default, ABAQUS/CAE uses the information stored in the IGES-file to decide
how the trim curve is defined; alternatively, you can force ABAQUS/CAE to always use either
real three-dimensional space or parameter space.
For more information, see ``Understanding the contents of an IGES file,'' Section 13.2.
Click OK to close the IGES Options dialog box.
6. From the Import from IGES dialog box, click OK to import the IGES part.
ABAQUS/CAE displays the Create Part from IGES File dialog box.
7. ABAQUS/CAE uses the name of the file to name the part and assumes that the part type is
deformable; you can use the Create Part from IGES File to change the part's name and type if
desired. ABAQUS/CAE tries to determine the modeling space as follows:
· If ABAQUS/CAE determines the part is planar, you can choose whether the modeling space is
two- or three-dimensional.
· If ABAQUS/CAE determines the part is planar and that its geometry does not cross the Y-axis,
you can choose whether the modeling space is axisymmetric, two-dimensional, or
three-dimensional. If you choose axisymmetric, the Y-axis is assumed to be the axis of
revolution, and you can choose whether to include a twist degree of freedom.
2-309
Importing and exporting geometry data and models
8. If desired, click the Repair Options tab and toggle the desired repair operations. For more
information, see ``Repairing an imported part,'' Section 13.5.8.
9. Click OK to exit the Create Part from IGES File dialog box.
ABAQUS/CAE scans the IGES file and starts the repair process, depending on the options
selected in step 8. If you wish to cancel the import process, click Stop in the prompt area.
When the part is imported, ABAQUS/CAE displays a message in the message area indicating if
the part contains any validity or precision problems. Select Part->Repair Geometry from the main
menu bar to try and repair an imported part.
· ``IGES entities recognized by ABAQUS/CAE when importing a part or a sketch,'' Section 13.5.5
Table 13-1. IGES entities recognized by ABAQUS/CAE when importing a part or a sketch.
ID Form IGES Entity Name
100 0 Circular arc
102 0 Composite curve
104 1 Conic arc: general
104 2 Conic arc: ellipse
104 3 Conic arc: parabola
106 11 Copious data: 2D path
106 12 Copious data: 3D path
106 63 Copious data: Closed 2D curve
2-310
Importing and exporting geometry data and models
2-311
Importing and exporting geometry data and models
base feature directly, but you can add additional features to it, such as a solid extrusion or a blind cut.
Detailed instructions for importing a part from a VDA-FS-format file:
2. From the File Type menu at the top of the Import Part dialog box, select VDA-FS (*.vda).
ABAQUS/CAE lists all the files in the selected directory with a .vda file extension.
3. Select the VDA-FS file containing the part to import, and click Continue.
ABAQUS/CAE displays the Create Part from VDA File dialog box.
4. ABAQUS/CAE uses the name of the file to name the part and assumes that the part type is
deformable; you can use the Create Part from VDA File dialog box to change the part's name and
type if desired. ABAQUS/CAE tries to determine the modeling space as follows:
· If ABAQUS/CAE determines the part is planar, you can choose whether the modeling space is
two- or three-dimensional.
· If ABAQUS/CAE determines the part is planar and that its geometry does not cross the Y-axis,
you can choose whether the modeling space is axisymmetric, two-dimensional, or
three-dimensional. If you choose axisymmetric, the Y-axis is assumed to be the axis of
revolution, and you can choose whether to include a twist degree of freedom.
5. If desired, click the Repair Options tab and toggle the desired repair operations. For more
information, see ``Repairing an imported part,'' Section 13.5.8.
6. Click OK to exit the Create Part from VDA File dialog box.
ABAQUS/CAE scans the VDA-FS file and starts the repair process, depending on the options
selected in Step 5. If you wish to cancel the import process, click Stop in the prompt area.
When the part is imported, ABAQUS/CAE displays a message in the message area indicating if
the part contains any validity or precision problems. Select Part->Repair Geometry from the main
menu bar to try and repair an imported part.
2-312
Importing and exporting geometry data and models
2. From the File Type menu at the top of the Import Part dialog box, select Output Database
(*.odb).
ABAQUS/CAE lists all the files in the selected directory with a .odb file extension.
3. Select the output database containing the part to import, and click Continue.
4. If the current part is not an orphan mesh, the Create Part from Output Database dialog box
appears. Do the following:
a. Enter the name of the part. By default, ABAQUS/CAE uses the name of the output
database to name the imported part, but you can change the name if desired.
ABAQUS/CAE determines the modeling space (three-dimensional, two-dimensional, or
axisymmetric) and type (deformable body, discrete rigid surface, or analytical rigid
surface) of the imported part from the output database, and you cannot change the
modeling space and type.
5. If the current part is an orphan mesh, you must select one of the following from the buttons that
appear in the prompt area:
2-313
Importing and exporting geometry data and models
Select Create new part to import the orphan mesh and create a new part. The Create Part
from Output Database dialog box appears, and you follow the steps described above.
Stitch edges
ABAQUS/CAE tries to remove duplicate edges, vertices, and trim surfaces. Stitching edges
usually results in valid geometry. However, due to internal tolerances, the resulting
representation of small features may not match the geometry that was intended in the original
2-314
Importing and exporting geometry data and models
file.
1. Follow the procedure to import a part. For more information, see ``Importing parts from an
ACIS-format file,'' Section 13.5.3; ``Importing a part from an IGES-format file,'' Section 13.5.4;
and ``Importing a part from a VDA-FS format file,'' Section 13.5.6.
2. From the Create Part from (ACIS, IGES, or VDA) File dialog box that appears, select the Repair
Options tab and toggle the desired repair operations.
Some of the operations are dependent on each other. For example, if you choose to stitch the edges
of a part, ABAQUS/CAE automatically toggles on the Convert to precise representation option.
3. Click OK.
ABAQUS/CAE imports the part and displays a message in the prompt area indicating if the part
has validity or precision problems.
4. If the part is still invalid or imprecise, select Part->Repair Geometry to use the geometry repair
tools. For more information, see ``Repairing and editing imported parts,'' Section 14.5.3.
2-315
Importing and exporting geometry data and models
and element definitions and the type of element assigned. The input file reader can import an orphan
mesh containing most of the commonly used elements types. However, the input file reader cannot
import an orphan mesh containing the following element types:
· Hydrostatic fluid and fluid link elements (F2D2, F3D3, F3D4, FAX2, and FLINK)
2-316
Importing and exporting geometry data and models
2. From the Import Model dialog box, select the input file (file extension .inp) to import, and click
Continue. For more information on specifying the file to open, see ``Using file selection dialog
boxes,'' Section 6.3.7.
ABAQUS/CAE imports the input file and creates a model using information from the supported
options. Unsupported options and parameters are ignored. The new model, which has the same
name as the input file, becomes the current model and appears in the model list below the toolbar.
· ``Importing models from ABAQUS/Standard and ABAQUS/Explicit input files,'' Section 13.4
· ``Understanding the files generated by creating and analyzing a model,'' Section 12.3
2-317
Importing and exporting geometry data and models
2. From the File Type menu at the top of the Export Sketch dialog box, select one of the following:
· ACIS (*.sat)
· IGES (*.igs)
ABAQUS/CAE lists all the files in the selected directory with the appropriate file extension.
3. Select the file to which you want to export the sketch, or type the name of a new file in the
Selection text field.
4. If you are exporting a sketch to an IGES file, you can select the application that you expect to read
the file. You can choose one of the following:
· Neutral
· AutoCAD
· Solid Works
· JAMA
ABAQUS/CAE tailors the internal representation of the IGES file to match the format expected by
the selected application. By default, ABAQUS/CAE exports a sketch in a neutral format.
ABAQUS/CAE writes all of the geometry data to a single layer in the IGES file. The IGES file
contains geometry data only, ABAQUS/CAE does not export construction lines and dimensions
from the sketch.
5. Click OK to export the sketch and to close the Export Sketch dialog box.
2-318
Importing and exporting geometry data and models
ABAQUS/CAE exports the part most recently displayed in the Part module. You cannot export a part
that you imported from an output database.
Detailed instructions for exporting a part to an ACIS-, IGES-, or VDA-FS-format file:
2. From the File Type menu at the top of the Export Part dialog box, select one of the following:
· ACIS (*.sat)
· IGES (*.igs)
· VDA-FS (*.vda)
ABAQUS/CAE lists all the files in the selected directory with the appropriate file extension.
3. Select the file to which you want to export the part, or type the name of a new file in the Selection
text field.
4. If you are exporting a part to an IGES file, you can do the following:
· Select the application that you expect to read the file from one of the following:
- Standard
- AutoCAD
- SolidWorks
- JAMA
ABAQUS/CAE tailors the internal representation of the IGES file to match the format
expected by the selected application. By default, ABAQUS/CAE exports a part in a neutral
format.
ABAQUS/CAE writes all of the geometry data to a single layer in the IGES file. For more
information, see ``Understanding the contents of an IGES file,'' Section 13.2.
5. Click OK to export the part and to close the file selection dialog box.
2-319
Importing and exporting geometry data and models
2. Select the file to which you want to export the assembly, or type the name of a new file in the
Selection text field.
3. Click OK to export the assembly and to close the Export Assembly dialog box.
2-320
Creating and analyzing a model using the ABAQUS/CAE modules
0-321
The Part module
· ``Using the Sketcher in conjunction with the Part module,'' Section 14.10
1-322
The Part module
A part created using the Part module tools is called a native part and has a feature-based
representation. A feature captures your design intent and contains geometry information as well as a
set of rules that govern the behavior of the geometry. For example, a circular through cut is a feature,
and ABAQUS/CAE stores the diameter of the cut along with the information that it should pass all the
way through the part. If you increase the size of the part, ABAQUS/CAE recognizes that the depth of
the cut should increase so that it continues to pass through the part.
You use the Part module to create, edit, and manage the parts in the current model. ABAQUS/CAE
stores each part in the form of an ordered list of features. The parameters that define each
feature--extruded depth, hole diameter, sweep path, etc.--combine to define the geometry of the part.
The Part module allows you to do the following:
· Create deformable, discrete rigid, or analytical rigid parts. The part tools also allow you to edit and
manipulate the existing parts defined in the current model.
· Create the features--solids, shells, wires, cuts, and rounds--that define the geometry of the part.
· Use the Feature Manipulation toolset to edit, delete, suppress, resume, and regenerate a part's
features.
· Use the Sketcher to create, edit, and manage the two-dimensional sketches that form the profile of
a part's features. These profiles can be extruded, revolved, or swept to create part geometry, or they
can be used directly to form a planar or axisymmetric part.
· Use the Set toolset, the Partition toolset, and the Datum toolset. These toolsets operate on the part
in the current viewport and allow you to create sets, partitions, and datum geometry, respectively.
1-323
The Part module
action to save your parts before exiting the module; they are saved automatically when you save the
entire model by selecting File->Save or File->Save As from the main menu bar.
· Solids
· Shells
· Wires
· Cuts
· Blends
Using the tools in the Part module, you create and edit all the features necessary to describe each of the
parts in your model. ABAQUS/CAE stores each feature and uses this information to define the entire
part, to regenerate the part if you modify it, and to generate an instance of the part in the Assembly
module. For more information on how parts are related to part instances, see ``Part instances,'' Section
14.3.3.
The following sequence illustrates how the three-dimensional part in Figure 14-1 would be constructed
using each of the features available in ABAQUS/CAE.
Figure 14-1 Part constructed using solid, shell, wire, cut, and blend features.
1-324
The Part module
1. The first feature you create while building a part is called the base feature; you construct the
remainder of the part by adding more features that either modify or add detail to the base feature.
In this example the base feature is a U-shaped part; the user sketched a two-dimensional profile
and extruded it to form the base feature, as shown in Figure 14-2.
The sketch and the extrusion depth (a) are the modifiable parameters that define the base feature.
You can revisit the base feature and change its size or shape by using the Feature Manipulation
toolset to modify either the section sketch or the extrusion distance. If desired, you can delete the
base feature and sketch a new shape.
2. A stiffening web is added as a shell feature. The user sketched a line on one of the internal faces
and extruded the sketch to the opposite face, as shown in Figure 14-3. The sketch is the only
modifiable parameter that defines the shell feature.
1-325
The Part module
3. Rods are added to the corners as wire features. The wire was created by connecting two points that
the user selected, as shown in Figure 14-4. Wires created in this way have no modifiable
parameters; they must be deleted and recreated if you need to change them.
4. A blind cut is cut into the top of the clamp. The user sketched a two-dimensional profile, and the
profile was extruded into the clamp through a specified distance, as shown in Figure 14-5. The
sketch and the depth of the slot are the modifiable parameters that define the blind cut feature.
1-326
The Part module
5. The edges of the cut are rounded. The user selected the edges to round and provided the radius of
the round, as shown in Figure 14-6. The radius is the modifiable parameter that defines the round
feature.
If the geometry of a new feature depends on an existing feature, ABAQUS/CAE creates a parent-child
relationship between the features. The new feature is the child, and the feature it depends on is the
parent. For example, in the part described above the round feature is a child of the cut feature. If you
change the position or size of the cut, the edges remain rounded. Similarly, if you delete the cut,
ABAQUS/CAE also deletes the rounds.
If you modify a parent feature, the modification may invalidate children of the parent feature. For
example, in the part described above if you were to increase the depth of the cut so that it became a
through cut, you would lose the fillets along its edges; that is, the fillets would fail to regenerate after
the modification. ABAQUS/CAE offers you the following two choices:
· Keep the changes to the parent feature but suppress the features that failed to regenerate. Children
of the suppressed features will also be suppressed.
· Abort the modification of the parent feature and return to the state of the last successful
regeneration.
1-327
The Part module
· Attach additional pieces to the billet (apply a solid extrusion, a revolved shell, or a sketched wire).
· Cut away the billet (apply an extruded cut, a revolved cut, a circular hole, or round or chamfer an
edge).
When you create a new part, you must describe the base feature. You do this by specifying two
properties of the base feature: its shape and type. The shape indicates the basic topology of the feature;
that is, whether it is a solid, shell, or wire. The type indicates which of the following four methods will
be used to generate the part:
Planar
You sketch the feature on a two-dimensional sketch plane.
Extrusion
You sketch the feature profile and then extrude it through a specified distance.
Revolution
You sketch the feature profile and then revolve it by a specified angle about an axis.
Sweep
You sketch two shapes: a sweep path and a sweep profile. The profile is then swept along the
path to create the feature.
Before you create a part and choose the shape and the type of the base feature, you should know the
sequence you will use to construct the desired part. Choosing the correct type and shape of the base
feature is important.
Table 14-1 shows the base features that you can select based on the part's modeling space and type:
1-328
The Part module
Three-dimensional Two-dimensional or
Part Type Axisymmetric
Deformable Any Planar shell or planar wire
Discrete rigid Any (you must convert a 3-D Planar shell or planar wire
solid discrete rigid part to a
shell before you instance it)
Analytical Extruded or revolved shell Planar wire
rigid
An ACIS, IGES, or VDA-FS part consists of a single feature that you import into ABAQUS/CAE as
the base feature of a new part. You cannot modify this base feature, but you can add additional features
to it. Similarly, an orphan mesh is imported from an output database as the base feature of a new part.
You can use the mesh editing tools to add and delete nodes and elements from an orphan mesh.
· One body
· One axle
· One handle
1-329
The Part module
· One wheel
You then position the instances relative to a common coordinate system, thereby creating the model of
the cart, as shown in Figure 14-8.
Now, suppose you want to reduce the diameter of the wheels. You return to the Part module and
modify the diameter of the wheel by editing the original part. When you return to the Assembly
module, ABAQUS/CAE recognizes that the part was modified and automatically regenerates the four
instances of the wheel to reflect the change in the diameter.
You can create multiple instances of a single part. In addition, you can assemble instances of
deformable, analytical rigid, and discrete rigid parts when you are solving contact problems. For more
information on the types of parts you can create in ABAQUS/CAE, see ``Part types,'' Section 14.4.2.
1-330
The Part module
Sets are not transferred when you create a part instance from a part. For example, you might use the
Property module to create a set from the geometry of a part and assign a section to that set; however,
that set is not available later when you work with the part instance in the Assembly module.
Three-dimensional
ABAQUS/CAE embeds the part in the X-, Y-, Z coordinate system. A three-dimensional part
can contain any combination of solid, shell, wire, cut, round and chamfer features. You model
a three-dimensional part using three-dimensional solid, shell, beam, truss, or membrane
elements.
Two-dimensional planar
ABAQUS/CAE embeds the part in the X-Y plane. A two-dimensional planar part can contain a
combination of only planar shell and wire features, and all cut features are defined as planar
through cuts. You model a two-dimensional planar part using two-dimensional solid
continuum elements, as well as truss or beam elements.
Axisymmetric
ABAQUS/CAE embeds the part in the X-Y plane with the Y-axis indicating the axis of
revolution. An axisymmetric part can contain a combination of only planar shell and wire
features, and all cut features are defined as planar through cuts. You model an axisymmetric
part using axisymmetric solid continuum elements or axisymmetric shell elements.
Modeling space refers to the space in which the part is embedded rather than to the topology of the part
itself. Thus, you can create a three-dimensional part using a topologically two-dimensional shell
feature or a one-dimensional wire feature.
You cannot change an ABAQUS/CAE native part's modeling space after you have created the part.
When you import an orphan mesh from an output database, ABAQUS/CAE determines the modeling
1-331
The Part module
space of the new part from the information stored in the output database. When you import a part from
an ACIS-, IGES-, or VDA-FS-format file, you can specify the part's modeling space, provided that
ABAQUS/CAE does not determine it must be three-dimensional. Detailed instructions on how to
specify modeling space when creating and importing a part can be found in ``Choosing the modeling
space of a new part,'' Section 14.14.2, and ``Importing geometry data and models,'' Section 13.5.
Deformable
Any arbitrarily shaped axisymmetric, two-dimensional, or three-dimensional part that you can
create or import can be specified as a deformable part. A deformable part represents a part that
can deform under load; the load can be mechanical, thermal, or electrical. By default,
ABAQUS/CAE creates parts that are deformable.
Discrete rigid
A discrete rigid part is similar to a deformable part in that it can be any arbitrary shape.
However, a discrete rigid part is assumed to be rigid and is used in contact analyses to model
bodies that cannot deform.
Analytical rigid
An analytical rigid part is similar to a discrete rigid part in that it is used to represent a rigid
surface in a contact analysis. However, the shape of an analytical rigid part is not arbitrary and
must be formed from a set of sketched lines, arcs, and parabolas.
You can assemble deformable bodies, discrete rigid parts, and analytical rigid parts in the Assembly
module, but ABAQUS/CAE supports contact only between two deformable bodies or between a
deformable part and a rigid part.
You cannot change a part's type after you have created it. However, you can export a part in ACIS
format and then import it as a new ACIS part of a different type. When you import an orphan mesh,
ABAQUS/CAE determines the type of the new part from the information stored in the output database.
1-332
The Part module
In this example the mold is constrained to have no motion, and the die moves through a prescribed
path during the stamping process. You control the motion of rigid parts by selecting a rigid body
reference point and constraining or prescribing its motion. For more information, see ``The reference
point,'' Section 14.4.5.
You can choose between two kinds of rigid parts:
1-333
The Part module
an analytical rigid part is not arbitrary, and the profile must be smooth. You can use only the
following methods to create an analytical rigid part:
· You can sketch the two-dimensional profile of the part and revolve the profile around an
axis of symmetry to form a three-dimensional revolved analytical rigid part, as shown in
Figure 14-10.
· You can sketch the two-dimensional profile of the part and extrude the profile infinitely to
form a three-dimensional extruded analytical rigid part. Although ABAQUS/CAE
considers that the extrusion extends to infinity, the Part module displays a
three-dimensional extruded analytical rigid part with a depth that you specify, as shown in
Figure 14-11.
· You can sketch the profile of a planar two-dimensional analytical rigid part, as shown in
Figure 14-12.
1-334
The Part module
· You can sketch the profile of an axisymmetric two-dimensional analytical rigid part, as
shown in Figure 14-13.
You can import a part from an ACIS-, IGES-, or VDA-FS-format file and define it to be either
a deformable or a discrete rigid part; however, you cannot define an imported part to be an
analytical rigid part. As an alternative, you can import the geometry of the analytical rigid part
into a sketch. You can then create a new analytical rigid part and copy the imported sketch
into the Sketcher toolset.
· ``Defining analytical rigid surfaces,'' Section 2.3.4 of the ABAQUS/Standard User's Manual and
the ABAQUS/Explicit User's Manual
· ``Defining rigid bodies,'' Section 2.4 of the ABAQUS/Standard User's Manual and the
ABAQUS/Explicit User's Manual
· ``Rigid elements,'' Section 16.3.1 of the ABAQUS/Standard User's Manual and Section 15.3.1 of
the ABAQUS/Explicit User's Manual
· ``Contact and interaction analysis: overview, '' Section 21.1.1 of the ABAQUS/Standard User's
Manual and ``Contact analysis: overview,'' Section 20.1.1 of the ABAQUS/Explicit User's Manual
1-335
The Part module
Lines
You use the Sketcher's Line tool to sketch straight lines.
Splines
You use the Sketcher's Spline tool to sketch parabolas. You create a parabola by defining a
three-point spline, where the three points are the start of the spline, a point anywhere along the
spline, and the end of the spline. Only splines composed of exactly three points generate the
parabolas required by the analytical rigid part definition; consequently, ABAQUS/CAE
displays an error message if you create a spline using more than three points while sketching
the profile of an analytical rigid part.
You can construct an analytical rigid part from any combination of lines, arcs, and parabolas; however,
the resulting profile must be a single connected (but not necessarily closed) curve. In addition, the
curve must be smooth to obtain a converged solution with ABAQUS/Standard or ABAQUS/Explicit.
You may want to apply a sequence of small lines, arcs, or parabolas to eliminate any surface
discontinuities (ABAQUS/CAE does not have an equivalent to the FILLET RADIUS parameter on the
ABAQUS/Standard and ABAQUS/Explicit *SURFACE option). For more information on creating
parabolas and maintaining tangency, see ``Sketching splines,'' Section 22.9.8. For more information on
the rules governing analytical rigid surfaces, see ``Defining analytical rigid surfaces,'' Section 2.3.4 of
the ABAQUS/Standard User's Manual and the ABAQUS/Explicit User's Manual.
A sketch of an analytical rigid part that includes a line, an arc, and a fillet is illustrated in Figure 14-14.
1-336
The Part module
An analytical rigid part is defined completely by the two-dimensional profile of the base feature that
you create with the Sketch; consequently, the Part module tools cannot be used to add features when
you return to the Part module from the Sketch. You can modify the part only by editing the original
sketch.
· If the part is a discrete or analytical rigid part, you use the reference point to indicate the rigid body
reference point. You use the Load/BC/IC module to apply constraints to the reference point or to
define the motion of the reference point using loads or boundary conditions. Motion or constraints
that you apply to the rigid body reference point are then applied to the entire rigid part. Similarly,
if you created an isothermal rigid part, you use the Load/BC/IC module to apply a temperature
constraint to the rigid body reference point.
Typically, the location of the rigid body reference point is not important; however, if the rigid
body moves freely in a dynamic analysis, its mass and rotary inertia influence the motion, and the
reference point should be placed at the center of mass. You can use the Query toolset to determine
the coordinates of the centroid of a solid, and you can use the Property module to assign mass and
rotary inertia section properties to the reference point. The section can also include optional
damping data.
· If the part is a deformable planar part, you can model it with generalized plane strain elements.
You must create a reference point to indicate the first extra node required by generalized plane
strain elements. ABAQUS/CAE places the second extra node at the same location as the first. You
cannot model initial curvature in the model in the axial direction; for more information on
generalized plane strain elements, see ``Choosing the element's dimensionality,'' Section 13.1.2 of
the ABAQUS/Standard User's Manual.
1-337
The Part module
· You can create and name a set containing the reference point. You can then use the set when
creating an equation constraint in the Interaction module. You can also refer to the set in the
keywords editor when creating a multi-point constraint.
You use the Part module to create a reference point. From the main menu bar, select
Assign->Reference Point and use either of the following techniques:
Select in Viewport
You can select any existing vertex from the part, including datum points.
Enter Coordinates
You can type the components of a vector representing the X-, Y-, and Z-coordinates of the
reference point.
ABAQUS/CAE displays the reference point at the desired location and labels it Ref Pt.
You can assign only one reference point to a part; ABAQUS/CAE asks you if you want to delete the
original point if you try to assign a second point. If you entered coordinates to define the reference
point, ABAQUS/CAE allows you to edit the X-, Y-, and Z-coordinates using the Feature Manipulation
toolset. You can use the Interaction module to define the rigid body's surface normals.
· ACIS
· IGES
· VDA-FS
For more information, see Chapter 13, "Importing and exporting geometry data and models."
Because ABAQUS/CAE treats imported parts as a single feature, you cannot use the feature
manipulation toolset to remove excessive detail, such as small holes and fillets, from an imported part.
However, you can use the geometry repair tools to edit an ACIS, IGES, or VDA-FS part. In general,
you can add features to an imported ACIS, IGES, or VDA-FS part so that the final geometry may be
very different from the part you imported. Similarly, you cannot add geometric features to a part
imported from an output database (ODB); however, you can use the mesh editing tools to modify its
nodes and elements. In addition, you can add reference geometry, called datum geometry to an orphan
mesh. (For more information, see ``Repairing and editing imported parts,'' Section 14.5.3, and Chapter
41, "The Datum toolset.")
You can assemble a combination of native parts, ACIS parts, IGES parts, VDA-FS parts, and parts
from an ODB in the Assembly module. You can mesh native parts and ACIS, IGES, and VDA-FS
parts in the Mesh module.
You can select File->Import->Part from the main menu bar at any time during a session. When you
1-338
The Part module
import a part into a model, ABAQUS/CAE switches to the Part module and displays the imported part
in the current viewport. In addition, the imported part becomes the base feature of a new part.
The following topics are covered:
· ``Imported parts from ACIS-, IGES-, and VDA-FS-format files,'' Section 14.5.2
· Edit nodes.
In addition, you can add reference geometry, called datum geometry to an orphan mesh. (For more
information, see Chapter 41, "The Datum toolset.")
Node and element sets are maintained when you import an orphan mesh. If you delete any nodes or
elements from the orphan mesh, they are also deleted from these sets. In addition, you can create new
sets using the Set toolset.
If the current part is an orphan mesh, you can choose to replace its mesh with the imported orphan
mesh. The name of the current part does not change, and the part maintains its original section
assignments.
1-339
The Part module
· ``Imported parts from ACIS-, IGES-, and VDA-FS-format files,'' Section 14.5.2
ACIS is a geometric modeling toolkit that serves as the underlying geometry engine for many
three-dimensional modeling applications, including ABAQUS/CAE. Consequently, the ACIS format
has become an industry standard for storing the geometry of a part, and parts stored in ACIS format
can be interchanged between many applications. An ACIS-format file can contain more than one part,
and ABAQUS/CAE allows you to import each one separately.
The Initial Graphics Exchange Specification (IGES) is a similar industry standard, and IGES-format
files contain a neutral data format designed for graphics exchange between computer-aided design
(CAD) systems. An IGES-format file can contain only one part.
The Verband der Automobilindustrie e.V. (VDA) surface data format is a geometry standard
developed by the German automotive industry. Both VDA-FS and IGES files contain a mathematical
representation of the part in an ASCII format; however, the VDA-FS standard is simpler and
concentrates on geometry information.
ABAQUS/CAE can import a part stored in an ACIS-, IGES-, or VDA-FS-format file, but the imported
part does not retain any record of the features that originally defined it. As a result, the imported part
forms the base feature of a new part; you can add features to the part, but you cannot edit this base
feature.
In general, you can import any part saved in ACIS, IGES, or VDA-FS format; however, subsequent
operations, such as partitioning and meshing, may fail if the geometry is not valid. ABAQUS/CAE can
detect and repair invalid geometry during the import process, or you can repair the imported part in the
Part module. For more information, see ``Repairing and editing imported parts,'' Section 14.5.3.
You can use ACIS, IGES, and VDA-FS format to transfer parts between ABAQUS/CAE and
third-party solid modeling products, since ABAQUS/CAE can import and export parts in both formats.
The feature-based information stored in the part or part instance is lost when you export it to ACIS
format. To export a part from ABAQUS/CAE into an ACIS-, IGES-, or VDA-FS format file, select
File->Export->Part from the main menu bar. For detailed instructions on importing and exporting
parts, see ``Importing geometry data and models,'' Section 13.5, and ``Exporting geometry data,''
Section 13.7.
· ``Imported parts from ACIS-, IGES-, and VDA-FS-format files,'' Section 14.5.2
1-340
The Part module
If you import an invalid part into ABAQUS/CAE, you can try to correct the geometry using
the geometry repair tools. If you cannot correct the geometry using these tools, it cannot be
changed or analyzed in ABAQUS/CAE and is generally not useful.
If you import a valid but imprecise part into ABAQUS/CAE, you can try to increase the
precision of the geometry using the geometry repair tools. If you cannot make the geometry
more precise using these tools, you can still use the part in ABAQUS/CAE; however, some
ABAQUS/CAE functions will be disabled.
For detailed instructions on how to use the imported geometry repair tools, see ``Repairing
imported geometry,'' Section 14.21.
· Create a node. You can specify the coordinates of the new node either in the global
coordinate system or in a datum coordinate system that you specify.
· Edit nodes. You can specify the new coordinates of the nodes either in the global
coordinate system or in a datum coordinate system that you specify. You can edit a single
node or you can edit multiple nodes simultaneously.
· Delete nodes. Any elements associated with the deleted nodes are also deleted. In
addition, you have the option of deleting any remaining nodes that would be left
unassociated with any elements once the nodes selected for deletion and their associated
elements are deleted.
· Create an element. You must specify the shape of the element that you want to create, and
you must select the nodes in the order appropriate for that element shape.
1-341
The Part module
· Delete elements. You have the option of deleting any nodes that would be left
unassociated with any elements once the selected elements are deleted.
· Refine a planar, linear, triangular orphan mesh. ABAQUS/CAE maintains the edges of the
elements along the boundary of the part while improving the mesh quality in the interior.
Alternatively, you can specify a global element size before refining the mesh, and the
density of the new mesh reflects the new target element size.
For detailed instructions on how to use the orphan mesh editing tools, see ``Editing an orphan
mesh,'' Section 14.22.
· To create an extruded solid feature, you extrude the profile through a specified distance (d), as
shown in Figure 14-15. Select Shape->Solid->Extrude from the main menu bar to create this type
of feature.
1-342
The Part module
· To create a revolved solid feature, you revolve the profile through a specified angle (a). A
construction line serves as the axis of revolution, as shown in Figure 14-16. Select
Shape->Solid->Revolve from the main menu bar to create this type of feature.
· To create a swept solid feature, you sweep the profile along a specified path, as shown in Figure
14-17. Select Shape->Solid->Sweep from the main menu bar to create this type of feature. For
more information, see ``Defining the sweep path and the sweep profile,'' Section 14.9.3.
You can use any of the solid tools to add a solid feature to a deformable or discrete part that you
1-343
The Part module
created in three-dimensional modeling space. You cannot add a solid feature to a two-dimensional or
axisymmetric part.
Figure 14-15, Figure 14-16, and Figure 14-17 illustrate how each feature might later be meshed. You
can mesh a solid feature using any of the three-dimensional, solid continuum elements available in
ABAQUS/Standard or ABAQUS/Explicit.
· Sketch a line or curve and extrude it though a specified distance to create an extruded shell feature,
as shown in Figure 14-18. Select Shape->Shell->Extrude from the main menu bar to create this
type of feature.
· Sketch a line or curve and revolve it through a specified angle to create a revolved shell feature. A
construction line serves as the axis of revolution, as shown in Figure 14-19. Select
Shape->Shell->Revolve from the main menu bar to create this type of feature.
1-344
The Part module
· Sketch a path and a profile, and sweep the profile normal to the path to create a swept shell
feature, as shown in Figure 14-20. Select Shape->Shell->Planar from the main menu bar to create
this type of feature. For more information, see ``Defining the sweep path and the sweep profile,''
Section 14.9.3.
· Sketch the outline of the shell on a selected planar face or datum plane to create a planar shell
feature, as shown in Figure 14-21. When you sketch on a planar face (for example, the side of a
cube), the shell feature is created only where it extends beyond the face; a shell feature cannot
overlap a face. A sketch on a planar face of a cube and the resulting shell feature are shown in
Figure 14-21. In this example the shell feature is a fin extending beyond the selected face of the
cube. Select Shape->Shell->Planar from the main menu bar to create this type of feature.
1-345
The Part module
· Convert the faces of a solid feature to shell features; in effect, hollow out a solid. A
shell-from-solid feature is shown in Figure 14-22. Select Shape->Shell->From Solid from the
main menu bar to create this type of feature.
· Remove selected faces from a solid and convert the remaining solid to shell features. A
remove-face shell feature is shown in Figure 14-23. Select Shape->Shell->Remove Face from
the main menu bar to create this type of feature.
1-346
The Part module
You can use any of the shell tools to add a shell feature to a part that you created in three-dimensional
modeling space; however, when you are working on parts created in two-dimensional or axisymmetric
modeling space, you can use only the planar shell tool to add a shell feature. You use the Property
module to create a section prescribing the desired thickness and to assign the section to the shell
feature. For more information, see ``Defining sections,'' Section 15.2.3, and ``Assigning sections,
material orientations, and beam orientations to a part, '' Section 15.3.
Figure 14-21 and Figure 14-23 illustrate how each feature might later be meshed. You can mesh a shell
feature using:
· Membrane elements
· Sketch a wire on a selected planar face or datum plane to create a sketched wire feature, as shown
in Figure 14-24. Select Shape->Wire->Sketch from the main menu bar to create this type of
feature.
When you sketch on a planar face (for example, the side of a cube), the wire feature is created only
where it extends beyond the face. A wire feature cannot overlap a face; however, you can partition
the face to simulate a wire extending over the face.
· Connect two selected points with a straight line, as shown in Figure 14-25. Select
Shape->Wire->2 Points from the main menu bar to create this type of feature.
1-347
The Part module
You can use the wire tools to add a wire feature to any deformable or discrete rigid part. You cannot
add a wire feature to an analytical rigid part; you can only modify the original sketch that defined that
part.
You use the Property module to create a section that prescribes the desired cross-sectional geometry
and to assign that section to the wire feature. (For more information, see ``Defining sections,'' Section
15.2.3, and ``Assigning sections, material orientations, and beam orientations to a part, '' Section 15.3.)
You can model a wire feature using any of the beam, truss, or axisymmetric shell elements available in
ABAQUS/Standard or ABAQUS/Explicit.
Note: Although you can create a mesh of beam elements, the current version of ABAQUS/CAE
allows you to assign only the following sections to a wire:
· Beam section
· Truss section
· Sketch the two-dimensional profile of the cut and extrude it through a specified distance ( d), as
shown in Figure 14-26. Select Shape->Cut->Extrude from the main menu bar to create this type
of feature.
1-348
The Part module
· Sketch the two-dimensional profile of the cut and revolve it through a specified angle ( a). A
construction line serves as the axis of revolution, as shown in Figure 14-27. Select
Shape->Cut->Revolve from the main menu bar to create this type of feature.
· Sketch the two-dimensional profile of the cut and sweep it along a specified path, as shown in
Figure 14-28. Select Shape->Cut->Sweep from the main menu bar to create this type of feature.
For more information, see ``Defining the sweep path and the sweep profile,'' Section 14.9.3.
1-349
The Part module
· Enter the diameter of a hole and the distance of its center from two selected edges, as shown in
Figure 14-29. Select Shape->Cut->Circular Hole from the main menu bar to create this type of
feature.
You can use the cut tools to add a cut feature to any deformable or discrete rigid part. You cannot add
a cut feature to an analytical rigid part; you can only modify the original sketch that defined that part.
· Smooth an edge with a circular blend of a specified radius, as shown in Figure 14-30. Select
Shape->Blend->Round/Fillet from the main menu bar to create this type of feature.
1-350
The Part module
· Bevel an edge with a chamfered blend of a specified length, as shown in Figure 14-31. Select
Shape->Blend->Chamfer from the main menu bar to create this type of feature.
You can use the blend tools to blend edges of a deformable or discrete rigid part that you created in
three-dimensional modeling space. You cannot add a blend feature to a two-dimensional or
axisymmetric part; however, you can blend its corners by editing the sketch of the part.
Plan a strategy
Feature-based modeling provides flexibility, but it can also add overhead to your model. For
1-351
The Part module
example, you can effectively suppress an extrusion by removing it with a cut feature. Although
you can restore the extrusion subsequently by removing the cut feature, the resulting part
contains additional feature-based information that can slow down regeneration. In addition,
dependencies may cause feature regeneration to fail if you add more detail to the part; and,
because the extrusion is no longer visible, the cause of the failure to regenerate may be hard to
determine.
Before you decide how to create a part, you should always consider if you will ever need to
modify the part in the future. If you decide that you might need to modify the part, you should
consider the techniques that you will use to create the features that define the part. The
simplest techniques may not provide the flexibility you need for modifying the features. You
may find it cumbersome to edit or suppress individual items of geometry, such as an extrusion,
a fillet, or a hole.
Alternatively, if you know that you will never change the final design, you may not need the
flexibility provided by feature-based modeling and can use the simplest and most convenient
techniques to define the part.
1. Create the basic geometry of a part using extrusions, revolutions, cuts, and sweeps.
1-352
The Part module
Figure 14-32 The sketched profile of a slot should extend beyond any surfaces that are cut.
1-353
The Part module
ABAQUS/Standard or ABAQUS/Explicit to reach a solution. The amount of detail you provide when
you create a part in the Part module should be a reflection of your goals. Alternatively, you can create a
part with detailed features but suppress them prior to meshing the assembly. For example, if a model
takes several days to analyze, you may wish to simplify it by suppressing features; you could then
submit an analysis that runs faster and checks your basic modeling assumptions. If the simplified
model behaves as expected, you can unsuppress the features and resubmit a full analysis.
For an example of different feature-based design approaches based on design and analysis intent,
consider the cover plate shown in Figure 14-33.
You could create the three-dimensional shell that models the plate in several ways:
2. Sketch a rectangular base feature, and add four separate cut features.
3. Sketch a rectangular base feature, and add a single cut feature that cuts all four holes.
Either of the three approaches would generate the same part, but your design intent and your analysis
intent govern the best approach. For example:
· Do you want to create and analyze plates of varying sizes with different sized holes for different
applications? If the diameter of all four holes is always identical, you should create all four holes
as a single cut feature. However, if the diameter of individual holes might differ, you should create
four separate cut features.
· Do you want to suppress features before you finalize your design? For example, you could perform
a series of analyses with the holes suppressed to determine the desired plate thickness. You could
then unsuppress the holes and analyze the finished model. In addition, suppressing features may
simplify the mesh that ABAQUS/CAE generates, or suppressing features may make the assembly
sweep meshable.
If you want to suppress all four holes in the example of the rectangular cover plate, you should
create all four holes as a single cut feature. However, if you want to suppress individual holes, you
should create four separate cut features. If the analysis is straightforward and you do not need to
analyze a simplified model, you should sketch a base feature that includes the four holes.
1-354
The Part module
· ``Defining the axis of revolution for axisymmetric parts and for revolved features, '' Section 14.9.2
· ``Defining the sweep path and the sweep profile,'' Section 14.9.3
ABAQUS/CAE provides the following methods for defining the extrusion distance:
Blind
Specify the distance over which ABAQUS/CAE extrudes the sketch. The sketch and the
distance define the feature and can be edited using the Feature Manipulation toolset. You can
use this method when creating extruded solid, shell, and cut features. Figure 14-34 illustrates a
blind extruded cut in a solid part.
Up to Face
Select a single face to which ABAQUS/CAE extrudes the sketch. The selected face does not
1-355
The Part module
have to be parallel to the sketch plane, and it can be a nonplanar face. If you select this method
to define the extrusion distance, only the sketch can be modified using the Feature
Manipulation toolset; if you wish to extrude to a different face, you must create a new
extruded cut feature. You can use this method when creating extruded solid, shell, and cut
features. Figure 14-35 illustrates a sketch extruded to a nonplanar face.
Through All
This method is available only for extruded cut features. ABAQUS/CAE extrudes the sketch
defining the profile of the cut completely though the part. If you select this method to define
the extrusion distance, only the sketch can be modified using the Feature Manipulation toolset.
Figure 14-36 illustrates a through all cut in a solid part.
1-356
The Part module
by selecting Part->Create from the main menu bar. When you sketch the part's base feature,
ABAQUS/CAE superimposes a vertical construction line representing the axis of rotation on
the Y-axis of the sketch. You can delete this construction line and redraw it at a different angle
and location; however, the finished sketch must contain a construction line representing the
axis of rotation.
You can sketch on either the right or the left of the construction line, and your sketch can
touch this line but cannot cross it. When you exit the Sketcher, ABAQUS/CAE prompts you to
enter the angle through which the sketch will be revolved. In addition, if the sketch contains
more than one construction line, ABAQUS/CAE prompts you to select the construction line
that will serve as the axis of rotation.
1-357
The Part module
The feature created by sweeping the sweep profile along the above path is shown in Figure 14-38.
The sketches that define the sweep path and the sweep profile can both be modified using the Feature
Manipulation toolset. The sweeping tools are available only when you are working on a deformable or
discrete part that you created in a three-dimensional modeling space.
The sweep profile must be closed when you are creating a swept solid or cut feature. However, unlike
the sweep profile, the sweep path can be open or closed regardless of whether you are creating a swept
1-358
The Part module
solid, shell, or cut feature. If the sweep path is closed, the two ends of the path must meet tangentially.
For example, the closed sweep paths labeled ``Bad'' in Figure 14-39 are not allowed because the ends
of the path meet at an angle.
1-359
The Part module
· ``Using the Feature Manipulation toolset in the Part module,'' Section 14.11.2
Datum plane
You can sketch directly on datum planes, and any features you sketch on a datum plane will be
projected onto the part. Projecting a sketch from a datum plane is useful if the part does not
already contain a convenient sketch plane.
For example, suppose you want to cut a hole straight through the three-dimensional triangular
part shown in Figure 14-40, parallel to the X-axis.
1-360
The Part module
The part does not already have a face that is suitable for sketching the profile of the hole;
sketching the profile directly on a face results in a hole normal to the face, as shown in Figure
14-41.
To cut the desired hole, first use the Datum toolset to create a datum plane on the Y-Z
principal plane, as shown in Figure 14-42.
Second, sketch the profile of the cut on the new datum plane, as shown in Figure 14-43.
When you exit the Sketcher, ABAQUS/CAE cuts the sketched hole through the part,
perpendicular to the datum plane and parallel to the X-axis. This cut is illustrated in Figure
14-44.
1-361
The Part module
Datum axis
You can use the Datum toolset to create a datum axis that you will select as the vertical
direction for the sketch when adding or modifying a feature to a three-dimensional solid.
Creating a datum axis is useful when the part does not already contain the necessary axis.
For example, suppose you want to cut a slot through the part as shown in Figure 14-45.
Sketching the slot is difficult because selecting either of the two straight edges of the part as
the sketch's vertical axis causes the sketch grid lines to align with the line you select, not with
the X- or Y-axis. To make it easier to create the slot with the desired orientation, first use the
Datum toolset to create a datum axis along the Y-axis, as shown in Figure 14-46.
When you select the datum axis to define the Sketcher's vertical direction, the Sketcher starts,
and its grid is aligned with the part's X- and Y-axes, as shown in Figure 14-47.
1-362
The Part module
· Geometric features, such as extruded solids, revolved shells, sketched wires, and rounded edges
· Repair operation
· Partitions
· Datum geometry
When the Feature Manipulation toolset asks you to select a feature, you can select it from the viewport.
Alternatively, you can click the Feature List button on the right side of the prompt area and select the
feature from the Feature List dialog box that appears.
Use the Feature Manipulation toolset in the Part module to edit, suppress, resume, and delete features
of a part. The feature manipulation tools are described below:
Edit
When you edit a feature, ABAQUS/CAE displays the feature editor. You can either modify the
feature's parameters directly or, if applicable, you can modify the sketch that forms the
two-dimensional profile or sweep path of a feature.
Suppress
Suppressing a feature temporarily removes it from the definition of the part. A suppressed
feature is invisible, cannot be meshed, and is not included in the analysis of the model. You
cannot suppress the base feature, and suppressing a parent feature will suppress all of its child
features.
Resume
1-363
The Part module
Resuming a feature restores a suppressed feature to the part; resuming a parent feature restores
all of its child features. You can choose to resume all features, the set of features most recently
suppressed, or a selected feature.
Delete
Deleting a feature removes it from the part. You cannot resume a deleted feature.
Select Tools->Query from the main menu bar, or click the query tool in the toolbar to start the
Query toolset.
You can use the Query toolset to request either general information or module-specific information.
For a discussion of the information displayed by general queries, see ``Obtaining general information
about the model,'' Section 44.2.2.
The following queries are specific to the Part module.
Part attributes
ABAQUS/CAE displays the part name, modeling space, and type in the message area.
1-364
The Part module
Geometry precision
ABAQUS/CAE highlights the regions of an imported part that have geometry precision
warnings.
Geometry validity
ABAQUS/CAE highlights the regions of an imported part that have geometry validity errors.
Volume properties
ABAQUS/CAE displays the volume and the centroid of the solid features of the part in the
message area. ABAQUS/CAE computes the volume using only the solid features of the part;
shell and wire features are not taken into consideration. ABAQUS/CAE does not display any
volume information if the part contains only shell and/or wire features.
1-365
The Part module
For information on using each of the Part module tools, refer to the following sections:
· The Create, Copy, Rename, and Delete items listed under the Part menu on the main menu bar.
The Copy, Rename, and Delete items contain submenus listing all the parts in the current model.
· The Part Manager dialog box. The Part Manager dialog box contains functions similar to those
listed under the Part menu on the main menu bar, but with a convenient browser that lists the
names of all the parts available within the current model along with their modeling space
(three-dimensional, two-dimensional, or axisymmetric) and type (deformable, discrete rigid, or
analytical rigid). To display the Part Manager dialog box, select Part->Manager from the main
menu bar.
To retrieve a part from the model database and display it in the current viewport, select the part from
1-366
The Part module
the Part list located under the toolbar. The Part list contains all the parts in the current model.
Tip: You can also create a part using the tool in the Part module toolbox. For a
diagram of the tools in the Part module toolbox, see ``Using the Part module toolbox,'' Section
14.12.
2. Type a name for the part. For information on naming ABAQUS/CAE objects, see ``Using basic
dialog box components,'' Section 6.3.1.
3. Choose the new part's modeling space, type, base feature, and approximate size. For more
information, see ``How is a part defined in ABAQUS/CAE?,'' Section 14.4.
Note: You can rename a part after you create it, but you cannot change its modeling space or type.
1-367
The Part module
5. Use the Sketcher to sketch the two-dimensional profile of the base feature. For more information,
see Chapter 22, "The Sketch module."
If you are constructing a swept part, you must first sketch the sweep path and exit the Sketcher.
The Sketch will then restart automatically, and you can sketch the profile to be swept.
6. When you have finished sketching the base feature, click mouse button 2 to exit the current
Sketch tool.
7. In the prompt area, click Done to exit the Sketcher. If the base feature is a three-dimensional solid
or shell extrusion, you must use the text field that appears in the prompt area to enter the distance
through which to extrude the profile. If the base feature is a three-dimensional revolved solid or
shell, you must enter the angle through which to rotate the profile.
ABAQUS/CAE exits the Sketcher and displays the new part in the current viewport.
8. If necessary, use the Part module tools to add additional features to the base feature. For more
information, see ``Understanding feature-based modeling,'' Section 14.3.
· ``Imported parts from ACIS-, IGES-, and VDA-FS-format files,'' Section 14.5.2
· ``Using the Create Part dialog box to define the properties of a part, '' Section 14.14.1
1-368
The Part module
14.14.1 Using the Create Part dialog box to define the properties
of a part
When you create a part, you first use the Create Part dialog box to define the properties of the part,
and then you use the Sketch to sketch the two-dimensional profile of the base feature. You use the
Create Part dialog box to define the following:
Name
Use the Name text field at the top of the Create Part dialog box to name the part you are
creating. To rename a part, select Part->Rename from the main menu bar. For information on
valid names, see ``Using basic dialog box components,'' Section 6.3.1.
After you create a part, ABAQUS/CAE displays the name of the new part in title bar of the
current viewport.
Modeling Space
Use the Modeling Space radio buttons to choose the modeling space of the new part. You can
define a part to be either three-dimensional, two-dimensional (planar), or axisymmetric. If you
create an axisymmetric deformable part, the Create Part dialog box allows you to include a
twist degree of freedom in your model. You cannot change a part's modeling space after you
create it. For more information, see ``Choosing the modeling space of a new part,'' Section
14.14.2.
Type
Use the Type radio buttons to choose the type of the new part. You can define a part to be
either deformable, discrete rigid, or analytical rigid. You cannot change a part's type after you
create it. For more information, see ``Choosing the type of a new part,'' Section 14.14.3.
Base Feature
Use the Base Feature field to define the shape and the type of the new part's base feature. The
shape and the type options that ABAQUS/CAE displays depend on the part's modeling space
and type. You cannot change the type of a part's base feature after you create it. For more
information, see ``Choosing the base feature of a new part,'' Section 14.14.4.
Approximate size
Use the approximate size text field to enter the size of the part. The size that you enter is used
by ABAQUS/CAE to calculate the size of the Sketcher sheet and the spacing of its grid. For
more information, see ``Setting the approximate size of the new part,'' Section 14.14.5. After
you create the part and start sketching its profile, you can use the Sketch customization
options to increase the sheet size. To display the Sketcher customization options click the
1-369
The Part module
Three-dimensional
ABAQUS/CAE positions the part in three-dimensional space.
Two-dimensional planar
ABAQUS/CAE positions the part in planar, two-dimensional space.
Axisymmetric
ABAQUS/CAE positions the part in axisymmetric two-dimensional space. If you create an
axisymmetric deformable part, ABAQUS/CAE allows you to include a twist degree of
freedom in your model.
1. From the top of the Create Part dialog box, choose the desired Modeling Space radio button.
2. When you have finished choosing options, click Continue to close the Create Part dialog box.
The Sketcher starts, and you sketch the profile of the new part's base feature.
1-370
The Part module
· ``Defining the axis of revolution for axisymmetric parts and for revolved features, '' Section 14.9.2
Deformable
Any arbitrarily shaped axisymmetric, two-dimensional, or three-dimensional part that you can
create or import can be specified as a deformable part. A deformable part represents a part that
can deform under load; the load can be mechanical, thermal, or electrical. By default,
ABAQUS/CAE creates parts that are deformable.
Discrete rigid
A discrete rigid part is similar to a deformable part in that it can be any arbitrary shape.
However, a discrete rigid part is assumed to be rigid and is used in contact analyses to model
bodies that cannot deform.
Analytical rigid
An analytical rigid part is similar to a discrete rigid part in that it is used to represent a rigid
surface in a contact analysis. However, the shape of an analytical rigid part is not arbitrary and
must be formed from a set of sketched lines, arcs, and parabolas.
After you create either a discrete rigid part or an analytical rigid part, you must also do the following:
· Assign the rigid body reference point. You apply constraints or prescribe motion to the rigid body
reference point in the Load/BC/IC module, and the same constraints or motion are applied to the
entire rigid part. For more information, see ``The reference point,'' Section 14.4.5.
· If the part is a discrete rigid part or an analytical rigid part, you must use the Surface toolset in the
Assembly module to choose which side of the part represents the outer surface. For more
information, see Chapter 45, "The Set and Surface toolsets."
If you create either a discrete rigid part or an analytical rigid part, you can toggle on Isothermal to
define an isothermal rigid part.
Detailed instructions for selecting the type of a new part:
1. From the middle of the Create Part dialog box, choose the desired Type radio button.
1-371
The Part module
2. When you have finished choosing options, click Continue to close the Create Part dialog box.
The Sketcher starts, and you sketch the profile of the new part's base feature.
· ``Defining analytical rigid surfaces,'' Section 2.3.4 of the ABAQUS/Standard User's Manual and
the ABAQUS/Explicit User's Manual
1. From the bottom of the Create Part dialog box, choose the desired base feature shape (Solid,
Shell, or Wire). The available choices depend on the modeling space and the type of the part you
are creating.
2. If you are creating a three-dimensional part, you must also choose its Type (Extrusion,
Revolution, Sweep , or Planar).
3. When you have finished choosing options, click Continue to close the Create Part dialog box.
The Sketcher starts, and you sketch the profile of the new part's base feature.
1-372
The Part module
· ``Defining the axis of revolution for axisymmetric parts and for revolved features, '' Section 14.9.2
1. Type the approximate size of the new part in the Approximate size text field at the bottom of the
Create Part dialog box.
2. When you have finished choosing options, click Continue to close the Create Part dialog box.
The Sketcher starts with a sheet size and grid spacing based on the approximate size of the new
part, and you sketch the profile of the new part's base feature.
1-373
The Part module
· Use the Solid tools to add a solid feature to a to a three-dimensional solid part.
· Use the Blend tools to add a blend feature to a three-dimensional solid part.
1-374
The Part module
You can also define the distance over which to extrude by selecting a single face to extrude to. The
selected face does not have to be parallel to the sketch plane, and it can be a nonplanar face.
ABAQUS/CAE extrudes the sketch until it meets the selected face.
Detailed instructions for adding an extruded solid feature:
Tip: You can also add an extruded solid feature using the tool, located with the solid
tools in the Part module toolbox. For a diagram of the tools in the Part module toolbox, see
``Using the Part module toolbox,'' Section 14.12.
2. Select the face from which the solid will be extruded. If the selection is ambiguous, you can cycle
through the candidate faces using the buttons in the prompt area.
An arrow appears, indicating the extrusion direction.
3. From the buttons in the prompt area, click Flip to reverse the arrow, if necessary. Click OK to
accept the indicated extrusion direction.
If the arrow direction is difficult to see, use the rotate tool from the toolbar to rotate the part.
4. Select an edge that will appear vertical and on the right of the Sketcher grid. The edge must not be
perpendicular to the selected face.
ABAQUS/CAE enters the Sketcher and rotates the part so that the selected face aligns with the
plane of the Sketcher grid and the selected edge aligns with the vertical grid lines.
Tip: If the selected face is curved or does not have a suitable edge, you can create a datum
axis that will provide the desired orientation. You can then select the datum axis as the edge to
appear vertical and on the right of the Sketcher grid.
If you are unsure of the part's orientation relative to the Sketcher grid, use the rotate tool from
the toolbar to view its position. Use the cycle tool to return to the original view.
5. Use the Sketcher to sketch the two-dimensional profile of the extrusion. In the prompt area, click
Done to indicate that you have finished sketching the profile.
6. From the buttons in the prompt area, select one of the following:
· Blind
b. Click mouse button 2 to accept the default value, or enter a new extrusion depth.
1-375
The Part module
ABAQUS/CAE exits the Sketcher and returns to the Part module. The part is displayed in
its original orientation with the solid extruded from the sketch plane through the desired
distance.
· Up to Face
a. ABAQUS/CAE exits the Sketcher and returns to the Part module with the part displayed
in its original orientation.
b. Select the face to which to extrude. The selected face does not have to be parallel to the
sketch plane, and it can be a nonplanar face. You cannot select a datum plane.
ABAQUS/CAE extrudes the solid from the sketch plane to the selected face.
The rotation angle as well as the sketch of the profile and the axis define the revolved solid feature;
both can be modified using the Feature Manipulation toolset.
1-376
The Part module
Tip: You can also add a revolved solid feature using the tool, located with the solid
tools in the Part module toolbox. For a diagram of the tools in the Part module toolbox, see
``Using the Part module toolbox,'' Section 14.12.
2. Select the face from which the solid will be revolved. If the selection is ambiguous, you can cycle
through the candidate faces using the buttons in the prompt area.
An arrow appears, indicating the normal to the axis of revolution and the initial direction of the
revolution.
3. From the buttons in the prompt area, click Flip to reverse the arrow, if necessary. Click OK to
accept the indicated direction.
If the arrow direction is difficult to see, use the rotate tool from the toolbar to rotate the part.
4. Select an edge that will appear vertical and on the right of the Sketcher grid. The edge must not be
perpendicular to the selected face.
ABAQUS/CAE enters the Sketcher and rotates the part so that the selected face aligns with the
plane of the Sketcher grid, and the selected edge aligns with the vertical grid lines.
Tip: If the selected face is curved or does not have a suitable edge, you can create a datum
axis that will provide the desired orientation. You can then select the datum axis as the edge to
appear vertical and on the right of the Sketcher grid.
If you are unsure of the part's orientation relative to the Sketcher grid, use the rotate tool from
the toolbar to view its position. Use the cycle tool to return to the original view.
6. Use the Sketcher to sketch the two-dimensional profile of the revolved feature; the sketch must not
cross the axis of revolution.
7. In the prompt area, click Done to indicate you have finished sketching the profile and the axis. If
the sketch contains more than one construction line, ABAQUS/CAE prompts you to select the
construction line that will serve as the axis of rotation.
1-377
The Part module
8. Click mouse button 2 to accept the default value, or enter a new revolve angle.
The part returns to its original orientation with the sketched profile revolved around the axis of
revolution.
· ``Defining the axis of revolution for axisymmetric parts and for revolved features, '' Section 14.9.2
1-378
The Part module
The sketch of the sweep path and the sketch of the sweep profile define the swept solid feature; both
can be modified using the Feature Manipulation toolset.
Detailed instructions for adding a swept solid feature:
Tip: You can also add a swept solid feature using the tool, located with the solid tools
in the Part module toolbox. For a diagram of the tools in the Part module toolbox, see ``Using
the Part module toolbox,'' Section 14.12.
2. Select the face on which to sketch the sweep path. If the selection is ambiguous, you can cycle
through the candidate faces using the buttons in the prompt area.
3. Select an edge that will appear vertical and on the right of the Sketcher grid. The edge must not be
perpendicular to the selected face.
ABAQUS/CAE enters the Sketcher and rotates the part so that the selected face aligns with the
plane of the Sketcher grid and the selected edge aligns with the vertical grid lines.
If you are unsure of the part's orientation relative to the Sketcher grid, use the rotate tool from
the toolbar to view its position. Use the cycle tool to return to the original view.
4. Sketch the sweep path. The sweep path must meet the following guidelines:
· The path can be closed, but the ends must meet smoothly; for example, the ends should not
meet at a corner. For examples of valid sweep paths, see ``Defining the sweep path and the
sweep profile,'' Section 14.9.3.
In the prompt area, click Done to indicate you have finished sketching the sweep path.
1-379
The Part module
ABAQUS/CAE exits the Sketcher and restores the original view of the part. A highlighted line
indicates the sweep path and its direction. You are now ready to sketch the sweep profile.
5. Select an edge that will appear vertical and on the right side of the Sketcher grid.
ABAQUS/CAE enters the Sketcher again and rotates the part so that the Sketcher grid lies on a
plane normal to the beginning of the sweep path. In addition, the selected edge aligns with the
vertical grid lines. The intersection of two dashed lines indicates the origin of the sweep path.
6. Sketch the sweep profile. The sweep profile must meet the following guidelines:
You can sketch the profile anywhere on the Sketcher grid; ABAQUS/CAE sweeps the profile
along a path parallel to the sweep path. In the prompt area, click Done to indicate you have
finished sketching the sweep profile.
ABAQUS/CAE exits the Sketcher, restores the original view of the part, and creates the new swept
solid.
· ``Defining the sweep path and the sweep profile,'' Section 14.9.3
1-380
The Part module
You can also define the distance over which to extrude by selecting a single face to extrude to. The
selected face does not have to be parallel to the sketch plane, and it can be a nonplanar face.
ABAQUS/CAE extrudes the sketch until it meets the selected face.
Detailed instructions for adding an extruded shell feature:
Tip: You can also add an extruded shell feature using the tool, located with the shell
tools in the Part module toolbox. For a diagram of the tools in the Part module toolbox, see
``Using the Part module toolbox,'' Section 14.12.
2. Select the face from which the shell will be extruded. If the selection is ambiguous, you can cycle
through the candidate faces using the buttons in the prompt area.
An arrow appears, indicating the extrusion direction.
3. From the buttons in the prompt area, click Flip to reverse the arrow, if necessary. Click OK to
accept the indicated extrusion direction.
If the arrow direction is difficult to see, use the rotate tool from the toolbar to rotate the part.
4. Select an edge that will appear vertical and on the right of the Sketcher grid. The edge must not be
perpendicular to the selected face.
ABAQUS/CAE enters the Sketcher and rotates the part so that the selected face aligns with the
plane of the Sketcher grid and the selected edge aligns with the vertical grid lines.
Tip: If the selected face is curved or does not have a suitable edge, you can create a datum
1-381
The Part module
axis that will provide the desired orientation. You can then select the datum axis as the edge to
appear vertical and on the right of the Sketcher grid.
If you are unsure of the part's orientation relative to the Sketcher grid, use the rotate tool from
the toolbar to view its position. Use the cycle tool to return to the original view.
5. Use the Sketcher to sketch the profile of the line to be extruded. In the prompt area, click Done to
indicate you have finished sketching the profile.
6. From the buttons in the prompt area, select one of the following:
· Blind
b. Click mouse button 2 to accept the default value, or enter a new extrusion depth.
ABAQUS/CAE exits the Sketcher and returns to the Part module. The part is displayed in
its original orientation with the shell extruded from the sketch plane through the desired
distance.
· Up to Face
a. ABAQUS/CAE exits the Sketcher and returns to the Part module with the part displayed
in its original orientation.
b. Select the face to which to extrude. The selected face does not have to be parallel to the
sketch plane, and it can be a nonplanar face. You cannot select a datum plane.
ABAQUS/CAE extrudes the shell from the sketch plane to the selected face.
1-382
The Part module
construction line serves as an axis of revolution, and ABAQUS/CAE creates the solid feature by
rotating the profile about the axis using a specified angle of revolution. A sketch and the resulting
feature, rotated about the axis of revolution through an angle of 90°, are illustrated in the following
figure:
The sketch and the rotation angle define the revolved shell feature; both can be modified using the
Feature Manipulation toolset.
Detailed instructions for adding a revolved shell feature:
Tip: You can also add a revolved shell feature using the tool, located with the shell
tools in the Part module toolbox. For a diagram of the tools in the Part module toolbox, see
``Using the Part module toolbox,'' Section 14.12.
2. Select the face from which the shell will be revolved. If the selection is ambiguous, you can cycle
through the candidate faces using the buttons in the prompt area.
An arrow appears, indicating the normal to the axis of revolution and the initial direction of the
revolution.
3. From the buttons in the prompt area, click Flip to reverse the arrow, if necessary. Click OK to
accept the indicated direction.
If the arrow direction is difficult to see, use the rotate tool from the toolbar to rotate the part.
4. Select an edge that will appear vertical and on the right of the Sketcher grid. The edge must not be
perpendicular to the selected face.
ABAQUS/CAE enters the Sketcher and rotates the part so that the selected face aligns with the
plane of the Sketcher grid and the selected edge aligns with the vertical grid lines.
Tip: If the selected face is curved or does not have a suitable edge, you can create a datum
axis that will provide the desired orientation. You can then select the datum axis as the edge to
appear vertical and on the right of the Sketcher grid.
1-383
The Part module
If you are unsure of the part's orientation relative to the Sketcher grid, use the rotate tool from
the toolbar to view its position. Use the cycle tool to return to the original view.
6. Use the Sketcher to sketch the two-dimensional profile of the revolved feature; the sketch must not
cross the axis of revolution.
7. In the prompt area, click Done to indicate you have finished sketching the profile and the axis. If
the sketch contains more than one construction line, ABAQUS/CAE prompts you to select the
construction line that will serve as the axis of rotation.
A default revolve angle appears in the prompt area.
8. Click mouse button 2 to accept the default value, or enter a new revolve angle.
The part returns to its original orientation with the sketched profile revolved about the axis of
revolution.
· ``Defining the axis of revolution for axisymmetric parts and for revolved features, '' Section 14.9.2
1-384
The Part module
The sketch of the sweep path and the sketch of the sweep profile combine to define the swept shell
feature, and both can be modified using the Feature Manipulation toolset.
Detailed instructions for adding a swept shell feature:
Tip: You can also add a swept shell feature using the tool, located with the shell tools
in the Part module toolbox. For a diagram of the tools in the Part module toolbox, see ``Using
the Part module toolbox,'' Section 14.12.
2. Select the face on which to sketch the sweep path. If the selection is ambiguous, you can cycle
through the candidate faces using the buttons in the prompt area.
1-385
The Part module
3. Select an edge that will appear vertical and on the right of the Sketcher grid. The edge must not be
perpendicular to the selected face.
ABAQUS/CAE enters the Sketcher and rotates the part so that the selected face aligns with the
plane of the Sketcher grid and the selected edge aligns with the vertical grid lines.
If you are unsure of the part's orientation relative to the Sketcher grid, use the rotate tool from
the toolbar to view its position. Use the cycle tool to return to the original view.
4. Sketch the sweep path. The sweep path must meet the following guidelines:
· The path can be closed, but the ends must meet smoothly; for example, the ends should not
meet at a corner. For examples of valid sweep paths, see ``Defining the sweep path and the
sweep profile,'' Section 14.9.3.
In the prompt area, click Done to indicate you have finished sketching the sweep path.
ABAQUS/CAE exits the Sketcher and restores the original view of the part. A highlighted line
indicates the sweep path and its direction. You are now ready to sketch the sweep profile.
5. Select an edge that will appear vertical and on the right side of the Sketcher grid.
ABAQUS/CAE enters the Sketcher again and rotates the part so that the Sketcher grid lies on a
plane normal to the beginning of the sweep path. In addition, the selected edge aligns with the
vertical grid lines. The intersection of two dashed lines indicates the origin of the sweep path.
6. Sketch the sweep profile. The sweep profile must meet the following guidelines:
You can sketch the profile anywhere on the Sketch grid; ABAQUS/CAE sweeps the profile along
a path parallel to the sweep path. In the prompt area, click Done to indicate you have finished
sketching the sweep profile.
7. ABAQUS/CAE exits the Sketcher, restores the original view of the part, and creates the new swept
shell. The resulting shell cannot intersect with itself.
· ``Defining the sweep path and the sweep profile,'' Section 14.9.3
1-386
The Part module
The sketch defines a planar shell feature and can be modified using the Feature Manipulation toolset.
Detailed instructions for adding a planar shell feature:
Tip: You can also add a planar shell feature using the tool, located with the shell tools
in the Part module toolbox. For a diagram of the tools in the Part module toolbox, see ``Using
the Part module toolbox,'' Section 14.12.
2. If the modeling space of the part is two-dimensional or axisymmetric, ABAQUS/CAE enters the
Sketcher and aligns the X- and Y-axes of the part and the sketch.
If the modeling space of the part is three-dimensional, do the following:
a. Select the face on which the shell will be positioned. If the selection is ambiguous, you
can cycle through the candidate faces using the buttons in the prompt area.
b. Select an edge that will appear vertical and on the right of the Sketcher grid. The edge
must not be perpendicular to the selected face.
ABAQUS/CAE enters the Sketcher and rotates the part so that the selected face aligns
with the plane of the Sketcher grid and the selected edge aligns with the vertical grid
lines.
Tip: If the selected face is curved or does not have a suitable edge, you can create a
datum axis that will provide the desired orientation. You can then select the datum
axis as the edge to appear vertical and on the right of the Sketcher grid.
If you are unsure of the part's orientation relative to the Sketcher grid, use the rotate tool
from the toolbar to view its position. Use the cycle tool to return to the original
view.
1-387
The Part module
3. Use the Sketcher to sketch the planar shell. In the prompt area, click Done to indicate you have
finished sketching.
The part returns to its original orientation with the planar shell positioned on the selected face. The
shell feature is created only where it extends beyond the faces of the part; a shell feature cannot
overlap a face.
Tip: You can also add a shell-from-solid feature using the tool, located with the shell
1-388
The Part module
tools in the Part module toolbox. For a diagram of the tools in the Part module toolbox, see
``Using the Part module toolbox,'' Section 14.12.
2. Select one or more cells to convert to shells. [Shift]+[Click] additional cells to add them to your
selection and [Ctrl]+[Click] a selected cell to unselect it. Click mouse button 2 to indicate you
have finished selecting cells to convert.
ABAQUS/CAE converts the selected cells to shells.
Tip: Use the backup button ( ) to undo one or more steps; use the cancel button ( ) to
abort the creation of the shell from solid.
Tip: You should use the remove-face tool only to create features that could not be created using
the other Shape tools. For example, you should not create a solid cylinder and then remove the
faces at each end to create a cylindrical shell. You should create the cylindrical shell directly using
the extruded or revolved shell tools.
1-389
The Part module
Tip: You can also add a remove-face shell feature using the tool, located with the shell
tools in the Part module toolbox. For a diagram of the tools in the Part module toolbox, see
``Using the Part module toolbox,'' Section 14.12.
2. Select one or more faces to remove from a solid feature. [Shift]+[Click] additional faces to add
them to your selection and [Ctrl]+[Click] a selected face to unselect it. Click mouse button 2 to
indicate you have finished selecting faces to remove. You must remove at least one face from a
solid feature of the part.
ABAQUS/CAE removes the selected faces and converts all remaining faces to shells.
Tip: Use the backup button ( ) to undo one or more steps; use the cancel button ( ) to
abort the creation of the shell from solid.
1-390
The Part module
The sketch fully defines a planar wire feature and can be modified using the Feature Manipulation
toolset.
Detailed instructions for adding a sketched wire feature:
Tip: You can also add a sketched wire feature using the tool, located with the wire
tools in the Part module toolbox. For a diagram of the tools in the Part module toolbox, see
``Using the Part module toolbox,'' Section 14.12.
2. If the modeling space of the part is two-dimensional or axisymmetric, ABAQUS/CAE enters the
Sketcher and aligns the X- and Y-axes of the part and the sketch.
If the part is three-dimensional, do the following:
a. Select the face on which the wire will be positioned. If the selection is ambiguous, you can
cycle through the candidate faces using the buttons in the prompt area.
b. Select an edge that will appear vertical and on the right of the Sketcher grid. The edge
must not be perpendicular to the selected face.
ABAQUS/CAE enters the Sketcher and rotates the part so that the selected face aligns
with the plane of the Sketcher grid and the selected edge aligns with the vertical grid
lines.
Tip: If the selected face is curved or does not have a suitable edge, you can create a
datum axis that will provide the desired orientation. You can then select the datum
axis as the edge to appear vertical and on the right of the Sketcher grid.
If you are unsure of the part's orientation relative to the Sketcher grid, use the rotate tool
from the toolbar to view its position. Use the cycle tool to return to the original
view.
3. Use the Sketcher to sketch the planar wire. In the prompt area, click Done to indicate you have
finished sketching.
1-391
The Part module
The part returns to its original orientation with the planar wire positioned on the selected face. The
wire feature is created only where it extends beyond the faces of the part; a wire feature cannot
overlap a face.
A wire feature connecting two points cannot be modified directly. In general, if you want to change
which points are connected, you must delete the wire and create a new wire connecting the desired
points. However, if the points you select are datum points that you created by specifying coordinates,
you can edit the datum points and change their location using the Feature Manipulation toolset.
Detailed instructions for adding a wire feature connecting two points:
· Vertices
1-392
The Part module
· Datum points
ABAQUS/CAE displays prompts in the prompt area to guide you through the procedure.
Tip: You can also add a wire feature connecting two points using the tool, located
with the wire tools in the Part module toolbox. For a diagram of the tools in the Part module
toolbox, see ``Using the Part module toolbox,'' Section 14.12.
2. Select the points that will locate the two ends of the wire. If the selections are ambiguous, you can
cycle through the candidate points using the buttons in the prompt area.
ABAQUS/CAE draws a wire connecting the two selected points. The wire feature is created only
where it extends beyond the faces of the part; a wire feature cannot overlap a face.
1-393
The Part module
· Blind extends the cut from the sketch plane in a selected direction but only to a specified depth.
· Up to Face extends the cut from the sketch plane to a selected face.
· Through All extends the cut from the sketch plane in a selected direction through the part.
You create an extruded cut in a two-dimensional or axisymmetric planar part by sketching the
two-dimensional cross-section of the cut directly on the plane of the part. The cut always passes
completely through the part.
Detailed instructions for cutting an extruded cut:
Tip: You can also create an extruded cut using the tool, located with the cut tools in
the Part module toolbox. For a diagram of the tools in the Part module toolbox, see ``Using the
Part module toolbox,'' Section 14.12.
a. Select the face from which the cut will be extruded. If the selection is ambiguous, you can
cycle through the candidate faces using the buttons in the prompt area.
1-394
The Part module
b. From the buttons in the prompt area, click Flip to reverse the arrow, if necessary. Click
OK to accept the indicated extrusion direction.
If the arrow direction is difficult to see, use the rotate tool from the toolbar to rotate the
part.
c. Select an edge that will appear vertical and on the right of the Sketcher grid. The edge
must not be perpendicular to the selected face.
ABAQUS/CAE enters the Sketcher and rotates the part so that the selected face aligns
with the plane of the Sketcher grid and the selected edge aligns with the vertical grid
lines.
Tip: If the selected face is curved or does not have a suitable edge, you can create a
datum axis that will provide the desired orientation. You can then select the datum
axis as the edge to appear vertical and on the right of the Sketcher grid.
If you are unsure of the part's orientation relative to the Sketcher grid, use the rotate tool
from the toolbar to view its position. Use the cycle tool to return to the original
view.
d. Use the Sketcher to sketch the two-dimensional profile of the extruded cut.
3. In the prompt area, click Done to indicate you have finished sketching the profile.
4. If the current viewport contains a two-dimensional or axisymmetric planar part, the part returns to
its original orientation, and ABAQUS/CAE cuts the plane with the sketched profile.
If the current viewport contains a three-dimensional part, select one of the following from the
buttons in the prompt area:
· Blind
b. Click mouse button 2 to accept the default value, or enter a new extrusion depth.
ABAQUS/CAE exits the Sketcher and returns to the Part module. The part is displayed in
its original orientation with the cut extruded from the sketch plane through the desired
distance.
· Up to Face
a. ABAQUS/CAE exits the Sketcher and returns to the Part module with the part displayed
in its original orientation.
b. Select the face to which to extrude. The selected face does not have to be parallel to the
1-395
The Part module
sketch plane, and it can be a nonplanar face. You cannot select a datum plane.
ABAQUS/CAE extrudes the cut from the sketch plane to the selected face.
· Through All
a. ABAQUS/CAE exits the Sketcher and returns to the Part module. The part is displayed in
its original orientation with the cut extruded from the sketch plane passing completely
through the part.
The sketch and the rotation angle combine to define the revolved cut, and both can be modified using
the Feature Manipulation toolset.
Detailed instructions for cutting a revolved cut:
1-396
The Part module
Tip: You can also create a revolved cut using the tool, located with the cut tools in the
Part module toolbox. For a diagram of the tools in the Part module toolbox, see ``Using the
Part module toolbox,'' Section 14.12.
2. Select the face from which the cut will be revolved. If the selection is ambiguous, you can cycle
through the candidate faces using the buttons in the prompt area.
An arrow appears, indicating the normal to the axis of revolution and the initial direction of the
revolution.
3. From the buttons in the prompt area, click Flip to reverse the arrow, if necessary. Click OK to
accept the indicated direction.
If the arrow direction is difficult to see, use the rotate tool from the toolbar to rotate the part.
4. Select an edge that will appear vertical and on the right of the Sketcher grid. The edge must not be
perpendicular to the selected face.
ABAQUS/CAE enters the Sketcher and rotates the part so that the selected face aligns with the
plane of the Sketcher grid and the selected edge aligns with the vertical grid lines.
Tip: If the selected face is curved or does not have a suitable edge, you can create a datum
axis that will provide the desired orientation. You can then select the datum axis as the edge to
appear vertical and on the right of the Sketcher grid.
If you are unsure of the part's orientation relative to the Sketcher grid, use the rotate tool from
the toolbar to view its position. Use the cycle tool to return to the original view.
6. Use the Sketcher to sketch the two-dimensional profile of the revolved cut; the sketch must not
cross the axis of revolution.
7. In the prompt area, click Done to indicate you have finished sketching the cross--section and the
axis. If the sketch contains more than one construction line, ABAQUS/CAE prompts you to select
the construction line that will serve as the axis of rotation.
A default revolve angle appears in the prompt area.
8. Click mouse button 2 to accept the default value, or enter a new revolve angle.
The part returns to its original orientation with the sketched profile revolved around the axis of
1-397
The Part module
· ``Defining the axis of revolution for axisymmetric parts and for revolved features, '' Section 14.9.2
The sweep profile is always perpendicular to the beginning of the path, and the profile always remains
normal to the path as it is swept along its length. The sketch of the sweep path and the sketch of the
sweep profile define the swept cut feature; both can be modified using the Feature Manipulation
toolset.
Detailed instructions for creating a swept cut feature:
Tip: You can also create a swept cut using the tool, located with the cut tools in the
Part module toolbox. For a diagram of the tools in the Part module toolbox, see ``Using the
Part module toolbox,'' Section 14.12.
2. Select the face on which to sketch the sweep path. If the selection is ambiguous, you can cycle
through the candidate faces using the buttons in the prompt area.
3. Select an edge that will appear vertical and on the right of the Sketcher grid. The edge must not be
perpendicular to the selected face.
ABAQUS/CAE enters the Sketcher and rotates the part so that the selected face aligns with the
1-398
The Part module
plane of the Sketcher grid and the selected edge aligns with the vertical grid lines.
If you are unsure of the part's orientation relative to the Sketcher grid, use the rotate tool from
the toolbar to view its position. Use the cycle tool to return to the original view.
4. Sketch the sweep path. The sweep path must meet the following guidelines:
· The path can be closed, but the ends must meet smoothly; for example, the ends should not
meet at a corner. For examples of valid sweep paths, see ``Defining the sweep path and the
sweep profile,'' Section 14.9.3.
In the prompt area, click Done to indicate you have finished sketching the sweep path.
ABAQUS/CAE exits the Sketcher and restores the original view of the part. A highlighted line
indicates the sweep path and its direction. You are now ready to sketch the sweep profile.
5. Select an edge that will appear vertical and on the right side of the Sketcher grid.
ABAQUS/CAE enters the Sketcher again and rotates the part so that the Sketcher grid lies on a
plane normal to the beginning of the sweep path. In addition, the selected edge aligns with the
vertical grid lines. The intersection of two dashed lines indicates the origin of the sweep path.
6. Sketch the sweep profile. The sweep profile must meet the following guidelines:
You can sketch the profile anywhere on the Sketch grid; ABAQUS/CAE sweeps the profile along
a path parallel to the sweep path. Click Done to indicate you have finished sketching the sweep
profile.
ABAQUS/CAE exits the Sketcher, restores the original view of the part, and creates the swept cut
through the part. The resulting cut cannot intersect with itself.
· ``Defining the sweep path and the sweep profile,'' Section 14.9.3
1-399
The Part module
The part must contain at least two straight edges; for example, you cannot use this tool to cut a hole
through a circular part.
If the current viewport contains a two-dimensional or axisymmetric planar part, the hole always passes
through all of the part. However, if the current viewport contains a three-dimensional part,
ABAQUS/CAE prompts you to select the type of cut. You can select one of the following types of
cut:
The distance from the hole to each edge, the diameter of the hole, and the depth of a blind hole are the
features that define a circular hole, and all three can be modified using the Feature Manipulation
toolset. You cannot change the type of cut--through all or blind--after the cut has been created.
Detailed instructions for cutting a circular hole:
Tip: You can also cut a circular hole using the tool, located with the cut tools in the
Part module toolbox. For a diagram of the tools in the Part module toolbox, see ``Using the
Part module toolbox,'' Section 14.12.
2. If the current viewport contains a two-dimensional part, select the first edge from which to
position the center of the hole.
If the current viewport contains a three-dimensional part, you must do the following:
a. From the buttons in the prompt area, select one of the following types of cut:
· Click Through All to cut a circular hole that extends from a selected face in a selected
direction through the part. A through cut is illustrated in the following example:
1-400
The Part module
· Click Blind to cut a circular hole that extends from a selected face in a selected
direction but only to a specified depth. A blind cut is illustrated in the following
example:
b. Select the face from which the hole will be cut. If the selection is ambiguous, you can
cycle through the candidate faces using the buttons in the prompt area.
An arrow appears, indicating the direction of the axis of the cut hole.
c. From the buttons in the prompt area, click Flip to reverse the arrow, if necessary. Click
OK to accept the indicated direction.
Tip: If the arrow direction is difficult to see, use the rotate tool from the toolbar to
rotate the part.
d. Select the first edge from which to position the center of the hole. The selected edges need
not lie in the same plane as the selected face, but they must not be perpendicular to it.
3. In the text field in the prompt area, type the distance from the selected edge to the center of the
hole.
4. Select the second edge from which to position the center of the hole. The two edges must not be
parallel.
5. In the text field in the prompt area, type the distance from the selected edge to the center of the
hole.
6. In the text field in the prompt area, type the diameter of the hole.
1-401
The Part module
You define the radius of the fillet, and ABAQUS/CAE applies the radius to all of the selected edges as
a group; therefore, subsequent feature manipulation operations, such as edit, delete, and suppress, will
be applied to the entire group of selected edges. Consequently, if you select more than one edge to
round, you cannot modify just one of the rounded edges. In addition, the shape of the resulting edges
can depend on the order in which you apply the fillets, as shown in the following figure. The fillets on
1-402
The Part module
the left side of the part were created by selecting all three edges and applying the round/fillet tool to
the group of selected edges in a single operation. In contrast, the fillets on the right side of the part
were created by selecting each edge individually and applying the round/fillet tool to each edge in
sequence.
The round/fillet tool is available only when the current viewport contains a three-dimensional solid
part. The radius of a rounded edge defines the feature and can be modified using the Feature
Manipulation toolset.
Detailed instructions for rounding edges:
Tip: You can also round selected edges using the tool, located with the blend tools in
the Part module toolbox. For a diagram of the tools in the Part module toolbox, see ``Using the
Part module toolbox,'' Section 14.12.
2. Select the edges to round, and click mouse button 2 to commit your selection. If the selection is
ambiguous, you can cycle through the candidate edges using the buttons in the prompt area.
[Shift]+[Click] additional edges to add them to your selection, and [Ctrl]+[Click] a selected edge
to unselect it.
A default radius appears in the prompt area.
3. If necessary, type a new radius in the text field in the prompt area. Click mouse button 2 to commit
the radius.
ABAQUS/CAE redraws the part with the selected edges rounded.
1-403
The Part module
ABAQUS/CAE applies the chamfer to all of the selected edges as a group; therefore, subsequent
feature manipulation operations--such as edit, delete, and suppress--will be applied to the entire group
of selected edges. Consequently, if you select more than one edge to chamfer, you cannot modify just
one of the chamfered edges.
The chamfer tool is available only when the current viewport contains a three-dimensional solid part.
The length of a chamfer defines the feature and can be modified using the Feature Manipulation
toolset.
Detailed instructions for chamfering edges:
Tip: You can also chamfer selected edges using the tool, located with the blend tools
in the Part module toolbox. For a diagram of the tools in the Part module toolbox, see ``Using
the Part module toolbox,'' Section 14.12.
2. Select the edges to chamfer, and click mouse button 2 to commit your selection. If the selection is
ambiguous, you can cycle through the candidate edges using the buttons in the prompt area.
[Shift]+[Click] additional edges to add them to your selection, and [Ctrl]+[Click] a selected edge
to unselect it.
A default chamfer length appears in the prompt area.
3. If necessary, type a new chamfer length in the text field in the prompt area. Click mouse button 2
to commit the chamfer length.
ABAQUS/CAE redraws the part with the selected edges chamfered.
1-404
The Part module
· Removing redundant vertices and edges from an imported part. For more information, see
``Removing redundant vertices or edges,'' Section 14.21.3.
· Creating a new face by selecting one edge. For more information, see ``Creating a new face,''
Section 14.21.4.
· Removing selected faces. For more information, see ``Removing a face,'' Section 14.21.5.
1-405
The Part module
· Converting a shell to a solid. For more information, see ``Creating a solid from a shell,'' Section
14.21.6
· Reducing the list of features that define a part to a simpler definition. For more information, see
``Reducing the feature list,'' Section 14.21.7
Some of the operations are dependent on each other. For example, if you stitch the edges of a part, you
must also convert it to an analytical representation. Similarly, if you convert the part to a more precise
representation, you must also stitch its edges and convert it to an analytical representation.
If your part is large and complex, the selected repair operations may take a long time to complete.
ABAQUS/CAE allows you to repair the part in a background process and to continue working on your
model. ABAQUS/CAE displays a message in the message area when the repair is complete, and the
repaired part becomes the current part.
Detailed instructions for repairing geometry:
2. From the dialog box, select Repair geometry and click OK.
ABAQUS/CAE displays the Repair Geometry dialog box.
1-406
The Part module
Stitch edges
ABAQUS/CAE tries to remove duplicate edges, vertices, and trim surfaces. Stitching
edges usually results in valid geometry. However, due to internal tolerances, the resulting
representation of small features may not match the geometry that was intended in the
original file.
4. If the repair process is expected to take a long time, you can repair the part in the background and
continue to work on your model. When the repair process is complete, ABAQUS/CAE writes a
notification in the message area and creates an ACIS file called partname-repaired.sat.
You must then import this file to make the repaired part available in your model. If you select
background processing, ABAQUS/CAE selects all of the repair options described above.
5. Click OK.
ABAQUS/CAE creates a backup of the part called partname-old-1 and repairs the original
part. When the repair operation is complete, the repaired part becomes the current part. If
partname-old-1 already exists, ABAQUS/CAE increments the last digit until it can create a
unique file name.
1-407
The Part module
You can use the repair tools to remove redundant vertices from a selected group of vertices. Similarly,
you can use the repair tools to remove redundant edges from a selected group of edges.
Warning: You should use the geometry repair tools to edit only imported parts. Where possible,
you should use the Part module tools to create and delete features from an ABAQUS/CAE native
part. The geometry repair tools may delete important feature information.
2. From the dialog box, select Remove redundant vertices and click OK.
3. Select the group of vertices from which ABAQUS/CAE should remove redundant vertices and
click mouse button 2 to indicate that you have finished selecting vertices.
ABAQUS/CAE removes the any redundant vertices from the selected group of vertices and closes
the Repair Geometry Tools dialog box.
2. From the dialog box, select Remove redundant edges and click OK.
3. Select the group of edges from which ABAQUS/CAE should remove redundant edges and click
mouse button 2 to indicate that you have finished selecting edges.
ABAQUS/CAE removes the any redundant edges from the selected group of edges and closes the
Repair Geometry Tools dialog box.
1-408
The Part module
2. From the dialog box, select Create face and click OK.
3. Select an edge that will be connected to the new face, and click mouse button 2 to confirm your
selection.
ABAQUS/CAE loops through the adjacent edges, selects the edges that define the boundaries of
the new face, and creates the new face.
1-409
The Part module
Warning: You should use the geometry repair tools to edit only imported parts. The geometry
repair tools do not take into account the feature-based representation of an ABAQUS/CAE native
part and may delete important feature information.
2. From the dialog box, select Remove face and click OK.
3. Select the faces that you want to remove, and click mouse button 2 to confirm your selection.
ABAQUS/CAE removes the selected faces.
1-410
The Part module
2. From the dialog box, select Solid from shell and click OK.
3. Select a face.
ABAQUS/CAE highlights the selected face and displays an arrow indicating the direction in which
material will be added to create the solid. If desired, click Flip to reverse the direction of the
arrow.
2. From the dialog box, select Reduce feature list and click OK.
3. From the Reduce Feature List dialog box that appears, click OK.
ABAQUS/CAE creates a backup of the part called partname-old-1 and reduces the feature
list of the original part. When the operation is complete, the modified part becomes the current
part. If partname-old-1 already exists, ABAQUS/CAE increments the last digit until it can
1-411
The Part module
In addition, you can use the Mesh module to change the element type associated with selected
elements; for more information, see ``Associating ABAQUS elements with mesh regions,'' Section
20.16.9. The following topics are covered:
· ``Reversing the surface normal direction of shell elements, '' Section 14.22.8
1-412
The Part module
2. In the dialog box, choose either Node or Element and the desired operation. For information on
each operation, see the following sections:
· ``Reversing the surface normal direction of shell elements, '' Section 14.22.8
3. Click OK to start the editing procedure and to close the Edit Mesh dialog box.
ABAQUS/CAE displays prompts in the prompt area to guide you through the procedure.
c. Click OK.
ABAQUS/CAE highlights the existing nodes. In hidden and shaded mode, only the visible nodes
are highlighted.
3. If desired, you can enter the coordinates for the new node in a datum coordinate system that you
have created rather than in the global coordinate system:
1-413
The Part module
b. In the viewport, select the datum coordinate system to be associated with the coordinates
of the new node. (For more information, see ``Creating datum coordinate systems,''
Section 41.8.)
4. In the Coordinates field in the prompt area, type the coordinates of the new node, and then press
[Enter].
ABAQUS/CAE creates the new node.
6. When you have finished creating nodes, click the cancel button in the prompt area to exit the
procedure.
c. Click OK.
ABAQUS/CAE highlights the existing nodes. In hidden and shaded mode, only the visible
nodes are highlighted.
3. In the prompt area, click the Selection method menu button, and select Individually from the list
that appears.
4. In the viewport, select the node that you want to edit, and click mouse button 2.
Tip: You can limit the types of objects that you can select in the viewport by clicking the
selection options tool in the prompt area and then clicking the options of your choice in
1-414
The Part module
the dialog box that appears. For more information, see Chapter 9, "Selecting objects within the
viewport."
5. If desired, you can enter new coordinates for the node in a datum coordinate system that you have
created rather than in the global coordinate system:
b. In the viewport, select the datum coordinate system to be associated with the new
coordinates of the node. (For more information, see ``Creating datum coordinate systems,''
Section 41.8.)
6. In the Coordinates field in the prompt area, type the new coordinates of the node, and then press
[Enter].
8. When you have finished editing nodes, click the cancel button in the prompt area to exit the
procedure.
If all of the selected nodes share the same value for a particular coordinate, that value appears in the
field for that coordinate in the Edit Nodes dialog box. For example, the figure above indicates that all
of the selected nodes have a value of -70 for their first coordinate and a value of 40 for their second
coordinate.
If the values for a particular coordinate are different for two or more of the selected nodes, the phrase
As is appears in the data field for that coordinate. For example, the figure above indicates that two or
more of the selected nodes have different values for the third coordinate.
The Edit Nodes dialog box also displays the range of values for each coordinate. For example, the
figure above indicates that the third coordinate values range from 10 to 20.
1-415
The Part module
You can edit the coordinates of the selected nodes in the following ways:
· If all of the nodes share the same value for a particular coordinate, you can change the value
entered in the data field for that coordinate. For example, in the figure above you could change the
second coordinate value of the selected nodes from 40 to 45.
· If two or more of the selected nodes have different values for a particular coordinate, you can
remove the As is designation in the data field for that coordinate and replace it with a particular
value. All of the selected nodes are given that value for the coordinate instead of retaining their
individual values.
The ability to assign a uniform coordinate value to multiple nodes is particularly useful when the nodes
must lie in the same plane--for example, when defining the mating surface of a cylinder head or engine
block. (For information on editing single nodes, see ``Editing nodes one at a time,'' Section 14.22.3.)
Detailed instructions for editing multiple nodes:
c. Click OK.
ABAQUS/CAE highlights the existing nodes. In hidden and shaded mode, only the visible
nodes are highlighted.
3. Use one of the following methods to select the nodes that you want to edit:
1. Click the Selection method menu button in the prompt area, and select Individually
from the list that appears.
1-416
The Part module
ABAQUS/CAE displays the Region Selection dialog box containing a list of node
sets that you have created.
2. Select the set of nodes that you want to edit, and click Continue.
Note: The default selection method is based on the selection method you most
recently employed. To revert to the other method, click Select in Viewport or Sets
on the right side of the prompt area.
1. Click the Selection method menu button in the prompt area, and select Face angle
from the list that appears.
Tip: You can limit the types of objects that you can select in the viewport by clicking the
selection options tool in the prompt area and then clicking the options of your choice in
the dialog box that appears. For more information, see Chapter 9, "Selecting objects within the
viewport."
The Edit Nodes dialog box appears displaying information about each coordinate for the selected
nodes. The value of a particular coordinate appears in the dialog box only if the value is the same
for all selected nodes. Otherwise, ABAQUS/CAE displays a value of As is indicating the
coordinate is different for at least two of the selected nodes.
4. In the Edit Nodes dialog box, use the following techniques to specify new coordinates:
· If a coordinate field displays the phrase As is, click the arrow on the right side of the field and
select Specify from the list that appears. Then enter the numeric value of your choice in the
field.
5. If desired, you can enter the new coordinates for the nodes in a datum coordinate system that you
1-417
The Part module
b. In the viewport, select the datum coordinate system to be associated with the new nodal
coordinates. (For more information, see ``Creating datum coordinate systems,'' Section
41.8.)
8. When you have finished editing nodes, click the cancel button in the prompt area to exit the
procedure.
c. Click OK.
ABAQUS/CAE highlights the existing nodes. In hidden and shaded mode, only the visible nodes
are highlighted.
3. In the viewport, select the nodes to delete. You can [Shift]+Click on individual nodes to add them
to your selection, or [Ctrl]+Click on selected nodes to remove them from your selection.
Tip: You can limit the types of objects that you can select in the viewport by clicking the
selection options tool in the prompt area and then clicking the options of your choice in
the dialog box that appears. For more information, see Chapter 9, "Selecting objects within the
viewport."
If you would rather select from a list of existing node sets, do the following:
1-418
The Part module
ABAQUS/CAE displays the Region Selection dialog box containing a list of node sets
that you have created.
b. Select the set of nodes that you want to delete, and click Continue.
Note: The default selection method is based on the selection method you most recently employed. To revert to the other
method, click Select in Viewport or Sets on the right side of the prompt area.
ABAQUS/CAE highlights the selected nodes and the elements associated with the selected nodes.
(Both the nodes that you have selected and any elements associated with those nodes will be
deleted.)
4. When you have finished selecting nodes to delete, click mouse button 2.
5. The elements associated with the selected nodes may also be associated with unselected nodes. If
those unselected nodes would be left unassociated with any element after the nodes and associated
elements are deleted, click Yes in the prompt area if you want ABAQUS/CAE to delete those
unselected nodes as well.
7. When you have finished deleting nodes, click the cancel button in the prompt area to exit the
procedure.
c. Click OK.
ABAQUS/CAE highlights the existing nodes. In hidden and shaded mode, only the visible nodes
are highlighted.
1-419
The Part module
3. In the prompt area, click the arrow next to the Element shape field, and select the element shape
of your choice from the list that appears.
4. In the viewport, select the nodes that will define the element. You must select the required number
of nodes for the element shape specified in the previous step. In addition, you must select the
nodes in a specific order. The figures below indicate the required node ordering for each element
shape:
1-420
The Part module
Once you have selected the required number of nodes, ABAQUS/CAE creates the new element.
6. When you have finished creating elements, click the cancel button in the prompt area to exit
the procedure.
1-421
The Part module
c. Click OK.
3. If you want to delete all nodes that are left unassociated with any elements once the selected
elements are deleted, toggle on Delete associated unreferenced nodes in the prompt area.
4. Select the elements to delete. You can [Shift]+Click on elements to add them to your selection or
[Ctrl]+Click on selected elements to remove them from your selection.
Tip: You can limit the types of objects that you can select in the viewport by clicking the
selection options tool in the prompt area and then clicking the options of your choice in
the dialog box that appears. For more information, see Chapter 9, "Selecting objects within the
viewport."
If you would rather select from a list of existing element sets, do the following:
b. Select the set of elements that you want to delete, and click Continue.
Note: The default selection method is based on the selection method you most recently employed. To revert to the other
method, click Select in Viewport or Sets on the right side of the prompt area.
5. When you have finished selecting elements to delete, click mouse button 2.
ABAQUS/CAE deletes the selected elements. In addition, if you toggled on Delete associated
unreferenced nodes , ABAQUS/CAE also deletes nodes that would be left unassociated with any
elements once the selected elements are deleted. The elements and nodes are also removed from
any existing sets.
7. When you have finished deleting elements, click the cancel button in the prompt area to exit
the procedure.
1-422
The Part module
Select Part->Edit Mesh from the main menu bar to reverse the surface normals of selected shell
elements from an orphan mesh. The elements can be either quadrilaterals or triangles. If you display
the orphan mesh using the shaded render style, the front and back faces of each shell element appear in
different colors. (See ``Choosing a render style,'' Section 46.2, for more information.)
Detailed instructions for reversing surface normals:
c. Click OK.
3. Use one of the following methods to select the shell elements whose normals you want to reverse:
1. Click the Selection method menu button in the prompt area, and select Individually
from the list that appears.
2. Select the set of element that you want to edit, and click Continue.
Note: The default selection method is based on the selection method you most
recently employed. To revert to the other method, click Select in Viewport or Sets
on the right side of the prompt area.
1. Click the Selection method menu button in the prompt area, and select Face angle
1-423
The Part module
2. Enter a face angle (from 0° to 90°), and select an element face. ABAQUS/CAE selects
every adjacent shell element from the selected face until the angle between the
element faces is equal to or exceeds the face angle. (See ``Using the face angle
method to create a surface from an orphan mesh,'' Section 9.2.3, for more
information.)
3. After you use the face angle method, you can [Shift]+Click on additional elements to
add them to your selection or [Ctrl]+Click on selected elements to remove them from
your selection. (See ``Combining selection techniques,'' Section 9.2.4, for more
information.)
Tip: You can limit the types of objects that you can select in the viewport by clicking the
selection options tool in the prompt area and then clicking the options of your choice in
the dialog box that appears. For more information, see Chapter 9, "Selecting objects within the
viewport."
4. In the prompt area, select a method for reversing the surface normal:
· Click Select normal to change the normals of the selected elements so that they point in the
same direction as the normal of a reference element that you specify.
6. Repeat the previous steps as often as necessary to change additional surface normals.
7. Click the cancel button in the prompt area to exit the procedure.
1-424
The Part module
If no element size is specified, ABAQUS/CAE maintains the edges of the elements along the
boundary of the part while improving the mesh quality in the interior of the part. The resulting
mesh topology is different from the original mesh topology. For example, a distorted mesh
appears in Figure 14-52.
When the part is remeshed, the quality of the mesh improves dramatically, as shown in Figure
14-53.
1-425
The Part module
Figure 14-55 shows the part remeshed with a global element size of 8.0.
2. If you want to specify a new global element size for the mesh, do the following:
a. In the Refine Mesh dialog box, select Size from the list of Action options.
b. From the Method list, select Set global element size, and click Apply.
1-426
The Part module
c. In the prompt area, type the global element size of your choice, and press [Enter].
ABAQUS/CAE uses the new element size that you have specified when remeshing the
part.
3. If you have applied a global element size to the part but decide that you would rather retain the
current element sizes at the part boundary, do the following:
a. In the Refine Mesh dialog box, select Size from the list of Action options.
b. From the Method list, select Remove global element size , and click Apply.
5. Accept Mesh part as the default Method selection, and click Apply.
1-427
The Property module
· Define materials.
· Define sections.
· Assign section definitions, material orientations, and beam section orientations to parts or regions
of parts.
· ``Assigning sections, material orientations, and beam orientations to a part, '' Section 15.3
The tutorial will help you become familiar with techniques for creating materials and for creating and
assigning sections.
2-428
The Property module
Shape-based profiles
Shape-based profiles define the specific shape and dimensions of the beam cross- section.
ABAQUS uses the information provided by the shape-based profile to calculate the
engineering properties of the section.
You can create this type of profile by first selecting from a list of shape options and then
specifying that particular shape's dimensions. For example, if you select a box shape, you must
then specify the height and width of the box as well as the thickness of the four walls. The
shape options currently available are shown below:
2-429
The Property module
Generalized profiles
Generalized profiles specify the engineering properties of the section directly. You can create
a generalized profile by specifying values for the area, moments of inertia, torsional rigidity,
and, if applicable, sectoral moment and warping constant. Referring to a generalized profile in
a beam section definition causes the *BEAM GENERAL SECTION option with the
SECTION=GENERAL parameter to be added to the analysis input file. For more information,
see ``Using the *BEAM GENERAL SECTION option to define the section behavior, '' Section
15.3.7 of the ABAQUS/Standard User's Manual.
Each profile that you create has its own name and is independent of any particular beam section; you
can refer to a single profile in as many beam sections as necessary.
2-430
The Property module
specifying a plane stress or plane strain thickness even if the section will be assigned to a
three-dimensional region. ABAQUS/CAE ignores the thickness information if it is not needed
for the region type.)
For more information, see ``Solid (continuum) elements,'' Section 14.1.1 of the
ABAQUS/Standard User's Manual and Section 13.1.1 of the ABAQUS/Explicit User's
Manual.
Membrane sections
Membranes represent thin surfaces in space that offer strength in the plane of the surface but
have no bending stiffness. Membrane sections consist of a material name, membrane
thickness, and section Poisson's ratio. For more information, see ``Membrane elements,''
Section 15.1.1 of the ABAQUS/Standard User's Manual and Section 14.1.1 of the
ABAQUS/Explicit User's Manual.
Beam sections
Beams are used in two and three dimensions to model slender, rod-like structures that provide
axial strength and bending stiffness. Beams represent structures in which the cross- section is
assumed to be small compared to the length. You can assign beam sections only to wire
regions. In addition, you must assign a beam section orientation to all regions with beam
sections.
Each beam section includes a section Poisson's ratio and a reference to a profile. Additional
information is required depending on whether you choose to calculate (integrate) the section
stiffness either before or during analysis (see ``Choosing whether to integrate before or during
analysis,'' Section 15.9.2, in the online version of this manual for more information).
For information about profiles, see Defining profiles, Section 15.2.2. For more information on
beam sections, see ``Beam modeling: overview,'' Section 15.3.1 of the ABAQUS/Standard
User's Manual and Section 14.3.1 of the ABAQUS/Explicit User's Manual.
2-431
The Property module
Truss sections
Trusses, like beams, are used in two and three dimensions to model slender, rod-like structures
that provide axial strength but no bending stiffness. Truss sections consist of a material name
and the cross-sectional area. For more information, see ``Truss elements,'' Section 15.2.1 of
the ABAQUS/Standard User's Manual and Section 14.2.1 of the ABAQUS/Explicit User's
Manual.
Point sections
Point sections are used to assign properties to rigid or isothermal bodies. The section
definition may include mass, rotary inertia, damping, and heat capacitance.
For more information, see the following sections:
· ``Point masses,'' Section 16.1.1 of the ABAQUS/Standard User's Manual and Section
15.1.1 of the ABAQUS/Explicit User's Manual
· ``Rotary inertia,'' Section 16.2.1 of the ABAQUS/Standard User's Manual and Section
15.2.1 of the ABAQUS/Explicit User's Manual
· ``Material damping,'' Section 12.1.1 of the ABAQUS/Standard User's Manual and Section
11.1.1 of the ABAQUS/Explicit User's Manual
· ``Point capacitance,'' Section 16.4.1 of the ABAQUS/Standard User's Manual and Section
15.4.1 of the ABAQUS/Explicit User's Manual
Gasket sections
Gaskets model thin sealing components that are positioned between structural components.
Gasket sections are used to provide pressure-closure behaviors for sealing components. Gasket
sections consists of a material reference, initial gasket thickness, initial gap, initial void, and
cross-sectional area. For more information, see ``Defining gaskets,'' Section 15.5, and ``Gasket
elements,'' Section 18.1 of the ABAQUS/Standard User's Manual.
Warning: The type of section that you assign to a part must be consistent with the element type
that you assign to instances of that part in the Mesh module. For example, if you assign a truss
section to a wire part in the Property module, you should assign a truss element type (and not a
beam element type) to any instances of that part in the Mesh module.
2-432
The Property module
· Select the region directly in the viewport. (See Chapter 9, "Selecting objects within the viewport,"
for information on selecting items in the viewport.)
· Use the Set toolset to create a set consisting of the region. (The Set toolset is available from the
Tools menu in the main menu bar.) You can then assign the section, material orientation, or beam
orientation to the region defined by the set. (See Chapter 45, "The Set and Surface toolsets," for
information on the Set toolset.)
If you assign a section to a region and then rename or delete the section, that section is no longer
applied to the region. If a region of your model lacks section properties, your analysis job will fail, and
the problem will be reported by the Job module.
However, the original names of renamed or deleted sections continue to be associated with the regions
to which they have been assigned until you take one of the following actions:
· Create a new section that has the original section name and is the appropriate type for the region
(for example, a shell section for a shell region); the properties defined in the new section are
applied to the region automatically.
· If you have renamed a section, change the name of the section back to its original name.
(You can use the Query toolset to determine the name of the section assigned to the region; for more
information, see ``Understanding the role of the Query toolset,'' Section 44.1.) Similarly, if you refer to
a material in a section definition and then rename or delete the material, the section becomes invalid;
properties defined in that section are no longer applied to regions to which the section is assigned.
However, the original names of renamed or deleted materials continue to be associated with sections
that refer to those materials; therefore, you can use techniques similar to the ones listed above to
restore sections.
For detailed instructions on assigning sections and material and beam orientations to a model, see the
following sections:
· ``Assigning a material orientation to a shell or solid part or region, '' Section 15.11.3
· ``Displaying information about section assignment and orientations for a particular region, ''
Section 15.11.4
2-433
The Property module
Each skin is defined by a surface, section name, material orientation, and offset. You can apply either a
homogeneous shell section, a membrane section, or a gasket section to a skin. Different skins can share
the same section; however, only one skin can be placed on a surface of a part--skins cannot overlap.
You may need to select the skin in subsequent modeling operations; for example, to:
· Create a display group to view the stress values on the skin elements in the Visualization module.
When you assign elements to the skin in the Mesh module, ABAQUS/CAE allows you to assign only
shell, membrane, or gasket elements. The skin elements share nodes with the underlying mesh when
the part is meshed. As a result, the order of the elements on the skin--linear or quadratic--is initially the
same as the order of the underlying elements. However, you can use mesh controls to assign a different
geometric order to the skin elements and to the three-dimensional elements.
The aircraft wing shown in Figure 15-1 is an example of how you might use a skin reinforcement in
your model.
Figure 15-1 An aircraft wing modeled by a solid honeycomb core and an aluminum skin.
The wing has a solid honeycomb core and an aluminum skin on the outside. You can create a solid part
representing the honeycomb and add a skin reinforcement representing the aluminum outer layer. In
the Mesh module you assign solid elements to the honeycomb and shell elements to the skin. The solid
and shell elements share the same nodes.
After you create a skin, you need to be able to select it in subsequent operations; for example, to assign
an element type to the skin in the Mesh module. In most cases you cannot select a skin directly from
the viewport. Instead, you must first create a named set that refers to the skin. When you are prompted
to select the geometry to include in the set, you must select the selection filter tool that appears in
the prompt area; and then select Skins from the list of objects to filter. The skin filter is available only
when you are creating a set. Otherwise, you can select only from the vertices, edges, faces, and cells in
2-434
The Property module
your model and can never select a skin. After you create the set that refers to the skin, you then select
the named set by clicking the Sets button from the right side of the prompt area.
1. In the Part module, define the solid geometry. Gasket parts are typically very thin, flat solids.
2. In the Property module, define a gasket material. The material can be a regular material or one that
includes special gasket behavior options. See ``Defining materials for gaskets,'' Section 15.6.7, for
more information.
3. In the Property module, define a gasket section that refers to the gasket material. Then assign the
gasket section to the gasket part.
4. In the Interaction module, establish appropriate tie constraints or contact interactions between the
gasket surfaces and the surfaces of adjacent part instances.
5. In the Mesh module, assign the sweep mesh technique to the gasket part instance, and choose a
sweep path with a direction normal to the gasket plane. See ``Assigning gasket elements to a
region,'' Section 20.5.4, for more information.
6. In the Mesh module, assign a gasket element type to the gasket region, and mesh the region.
Additional steps are required if the gasket model is composed of several layers and inserts. For
example, Figure 15-2 illustrates a compound gasket. The gasket is modeled as a solid layer with an
embedded shell-like layer for the insert.
2-435
The Property module
If you are working with compound gaskets, you must perform the following additional tasks:
1. Use the Partition toolset to partition the solid gasket region so that an internal surface is created at
the position of the insert.
2. In the Property module, define a skin reinforcement on the internal surface that represents the
insert. When you create the skin reinforcement, you must refer to a gasket section that you have
already created. (The gasket sections you assign to the solid and to the insert are usually different,
as are their materials.)
3. No meshing is required (or allowed) for the insert skin, but you must assign a three-dimensional
line gasket element type to the skin in the Mesh module. Currently you must use sets to assign
element types to skins, so first you must create a set using the skin selection filter. See ``Assigning
element types to skin reinforcements,'' Section 20.5.5, for more information.
When you model gaskets with solids, you can define how a gasket interacts with surrounding regions
by using one or a combination of the following techniques:
· You can create a separate gasket part and then use tie constraints or contact interactions to couple
the gasket part instance to the other part instances.
· You can create a thin region within a part and then assign a gasket section and element type to that
region.
If compatibility between the meshes of the gasket and its adjacent regions is important, the first
approach (creating a separate gasket part) is recommended.
2-436
The Property module
2-437
The Property module
Option menu
A set of menus beneath the option list from which you select material options. Each of the
options corresponds to a material option available in ABAQUS/Standard or
ABAQUS/Explicit; for example, *ELASTIC or *PLASTIC.
Note: You can display help on particular aspects of the editor that are not discussed here by
selecting Help->On Context from the main menu bar and then clicking the editor feature of
interest. A help window will appear containing a relevant section from this manual, from the
2-438
The Property module
ABAQUS/Standard User's Manual, from the ABAQUS/Explicit User's Manual, or from the
ABAQUS Keywords Manual.
Once you have created a profile, you can refer to that profile in a beam section definition. For example,
a box-shaped profile named SupportBeam is selected in the beam section editor shown in Figure
15-5.
2-439
The Property module
· ``Beam cross-section library,'' Section 15.3.9 of the ABAQUS/Standard User's Manual and Section
14.3.8 of the ABAQUS/Explicit User's Manual
· Gasket sections
To create a section, select Section->Create from the main menu bar. A Create Section dialog box
appears in which you can name the section and specify the type of section that you want to create.
Once you have specified a section name and type, click Continue in the Create Section dialog box to
display the section editor, which allows you to create and edit sections.
The format of the section editor varies according to the type of section you are defining. Most section
editors ask for a material name, a section Poisson's ratio, and a method for determining the temperature
variation. For example, the homogeneous shell section editor is shown in Figure 15-6.
2-440
The Property module
Note: You can display help on particular aspects of an editor that are not discussed here by
selecting Help->On Context from the main menu bar and then clicking the editor feature of
interest. A help window will appear containing a relevant section from this manual, from the
ABAQUS/Standard User's Manual, from the ABAQUS/Explicit User's Manual, or from the
ABAQUS Keywords Manual.
Some editors contain different Options buttons along the bottom of the dialog box similar to the
Integration option button shown in Figure 15-6. If you click an option button, another dialog box
appears in which you can enter data concerning that particular option. For example, if you click
Integration in the editor shown in Figure 15-6, a Homogeneous Shell Integration Options dialog
box appears, as shown in Figure 15-7.
Once you have entered all the data necessary to define the section, you can click OK to close the
section editor and to save the section.
For detailed instructions on using section editors, see the following sections:
2-441
The Property module
· ``Selecting a method for defining the temperature variation through the section, '' Section 15.9.3
· ``Specifying the number of section integration points in a homogeneous shell section, '' Section
15.9.4
The lists of options do not change to exclude options that are invalid for the type of analysis you are
running. In addition, ABAQUS/CAE does not check that the data that you enter in the editor are valid
or that your materials are appropriate for your analysis type. For example, if you request a dynamic
analysis, ABAQUS/Standard or ABAQUS/Explicit requires that you specify the density of the
materials used in the model so that it can calculate mass and inertia properties of the model. If you do
not provide a material density in the material definition, ABAQUS/CAE allows you to create the
material; however, ABAQUS/CAE will report an error when you submit your analysis job.
When you select an option, the name of the option appears in the Material Options list at the top of
the editor, and the option becomes part of your material definition. For example, the list in Figure 15-9
reflects that the Elastic and Plastic options have been chosen, as well as the Fail Stress suboption of
the Elastic option.
2-442
The Property module
Options such as Elastic and Plastic are primary options and correspond to the keywords *ELASTIC
and *PLASTIC in an analysis input file. Suboptions such as Fail Stress appear beneath the
corresponding primary option and are indented to indicate their subordinate position.
If you want to remove an option or suboption from a material definition, you can select that option or
suboption from the Material Options list and then click Delete.
If you are creating a new material, the selected option list is initially blank. As you select options, the
option name appears in the list; if there are too many options to see at once, a scroll bar appears on the
right side of the list.
A table containing fields for the remaining required material data appears beneath the parameter area;
for example, Figure 15-11 shows the table that appears when you choose isotropic elasticity.
2-443
The Property module
Different fields become available depending upon how you have set the parameters. For example,
when you choose lamina elasticity rather than isotropic elasticity, the table in Figure 15-12 appears.
You can enter data into the table using the keyboard. Alternatively, you can click mouse button 3
anywhere in the table to view a list of options for specifying tabular data. For example, an option exists
for automatically entering data from a file. Another option exists for creating an X-Y data object from
the data in the table; you can plot the X-Y data in the Visualization module and visually check its
validity. For detailed information on each option, see ``Entering tabular data,'' Section 6.3.5.)
For detailed information on specific features in the material editor, see the following sections:
2-444
The Property module
by a hyperelastic material and to choose a suitable material formulation. The Evaluate option prompts
ABAQUS/CAE to perform one or more standard tests using an existing material. (For information on
standard tests, see ``Hyperelasticity,'' Section 10.5 of the ABAQUS/Standard User's Manual and
Section 9.3 of the ABAQUS/Explicit User's Manual.) Once the standard tests are completed, new
viewports appear displaying the test results as X-Y plots. (For more information on X-Y plots, see
Chapter 30, "X-Y plotting.") You can review the results and adjust the material definition as necessary.
To initiate the evaluation procedure, select Material->Evaluate->material name from the main menu
bar. Alternatively, you can select the material of interest in the Material Manager and then click
Evaluate. The Evaluate Material Behavior dialog box appears in which you can specify how you
want ABAQUS/CAE to perform the standard tests. For detailed instructions on evaluating hyperelastic
material behavior, see ``Displaying X-Y plots of hyperelastic material behavior,'' Section 15.8.7.
The Evaluate option is particularly useful in the following scenarios:
Comparing test data with the behavior predicted by a particular strain energy potential
When you define a hyperelastic material using experimental data, you also specify the strain
energy potential that you want to apply to the data. ABAQUS uses the experimental data to
calculate the coefficients necessary for the specified strain energy potential. However, it is
important to verify that an acceptable correlation exists between the behavior predicted by the
material definition and the experimental data.
You can use the Evaluate option to perform one or more standard unit-element tests with the
experimental data using the strain energy potential that you have specified in the material
definition. When the tests are complete, an X-Y plot appears for each test that displays a
nominal stress-nominal strain curve for the material as well as a plot of the experimental data.
For example, the X-Y plot in Figure 15-13 shows the results of a planar test using the Ogden
N=3 strain energy potential.
2-445
The Property module
The path to the data ( .dat) file appears in the message area of the ABAQUS/CAE main
window once the analysis has completed successfully.
2-446
The Property module
gasket-specific behavior options and general-use materials. The type of material that you create
depends on your requirements for the gasket behavior.
· Create a material using the special gasket options if you want thickness direction, transverse shear,
and membrane behaviors to be uncoupled. When you refer to a gasket behavior material in a
gasket section definition, ABAQUS/CAE adds the *GASKET BEHAVIOR option to the analysis
input file instead of the *MATERIAL option. Gasket behavior materials are valid only for gasket
sections. For detailed information on this approach to defining gasket behavior, see ``Defining the
gasket behavior directly using a gasket behavior model,'' Section 18.1.6 of the ABAQUS/Standard
User's Manual.
· Create a general-use material if you want to consider only thickness tensile behavior. When you
refer to a general-use material in a gasket section definition, ABAQUS/CAE adds the
*MATERIAL option to the analysis input file as it would for any other type of section.
General-use materials are valid in gasket sections as well as in other types of sections. For detailed
information on this approach to defining gasket behavior, see ``Defining the gasket behavior using
a material model,'' Section 18.1.5 of the ABAQUS/Standard User's Manual.
You create a gasket-specific material by entering data for one or more of the options found in the
Other->Gasket submenu. Data entered for any other option in the material editor are ignored, with the
following exceptions:
· You can include the Expansion option (located in the Mechanical menu) in a gasket behavior
material definition.
· You can include the Depvar and User Output Variables options (located in the General menu) in
a gasket behavior material.
You create a general-use material by entering data for any options that are valid for gasket sections
except those found in the Other->Gasket submenu. (If you enter data for an option found in the
Other->Gasket submenu, you automatically create a gasket behavior material.) For information on
which material options are valid for general-use materials included in gasket section definitions, see
``Gasket elements,'' Section 18.1 of the ABAQUS/Standard User's Manual.
2-447
The Property module
3. Type a name of your choice in the Name text box, and click Continue.
The material editor appears with a blank options list and option definition area.
4. From the menu bar in the upper portion of the editor window, select
Mechanical->Elasticity->Elastic.
The parameters and data corresponding to isotropic elasticity appear in the option definition area
below the option menus, and the word Elastic appears in the Material Options list at the top of
the window.
5. In the option definition area, type Young's modulus and Poisson's ratio as shown in Figure 15-15.
Use the Tab key to move from one data cell to the next.
Note: The units for Young's modulus must be consistent with the units used elsewhere in the
model.
2-448
The Property module
6. From the menu bar in the upper portion of the editor window, select
Mechanical->Plasticity->Plastic. (Selecting a new option does not cause you to lose your
elasticity data.)
The parameters and data corresponding to von Mises plasticity appear in the option definition area
below the option menus, and the word Plastic appears in the Material Options list at the top of
the window.
7. In the option definition area, type values for yield stress and the corresponding plastic strain as
shown in the first row of Figure 15-16.
9. Type the second yield stress and plastic strain values in the appropriate cells, as shown in Figure
15-16. Be sure to enter the second set of data points in ascending order of plastic strain.
Note: The yield stress is assumed to remain constant for plastic strains exceeding the last value given.
10. Click OK to save your data and to exit the material editor.
2-449
The Property module
3. Type a name of your choice in the Name text box, and click Continue.
The material editor appears with a blank options list and option definition area.
4. From the menu bar in the upper portion of the editor window, select
Mechanical->Elasticity->Elastic.
The parameters and data corresponding to isotropic elasticity appear in the option definition area
below the option menus, and the word Elastic appears in the Material Options list at the top of
the window.
6. In the table, type values for Young's modulus and Poisson's ratio at the first temperature, as shown
in Figure 15-17.
Use the [Tab] key or the first mouse button to move from one cell to the next. There is no need to
enter plus signs (+) to indicate positive numbers.
7. Press [Enter] to add a blank row to the table. You can also add a row by pressing mouse button 3
over the table and selecting Add Row After from the menu that appears. For more information, see
``Entering tabular data,'' Section 6.3.5.
8. Type in a second Young's modulus, Poisson's ratio, and temperature in the appropriate cells, as
shown in Figure 15-18.
9. Continue adding rows after completing each row in the table. Fill in each row as shown in Figure
15-19. (To save time, you can skip this step.)
2-450
The Property module
10. Click OK to save your data and to exit the material editor.
3. Type a name of your choice in the Name text box, and click Continue.
The material editor appears with a blank options list and option definition area.
4. From the menu bar in the upper portion of the editor window, select
Mechanical->Elasticity->Hyperelastic.
The parameters and data corresponding to hyperelasticity appear in the option definition area
below the option menus, and the word Hyperelastic appears in the Material Options list at
the top of the window.
5. In the option definition area, accept Test data as the Input source selection.
6. Click the Strain energy potential button, and select Polynomial from the list that appears.
7. Accept Long-term as the default Moduli time scale (for viscoelasticity) selection.
2-451
The Property module
9. Click the Suboptions button in the upper right corner of the option definition area, and select
Uniaxial Test Data from the list that appears.
10. Click mouse button 3 in the first cell of the table, and select Read from File from the list that
appears.
The Read Data from ASCII File dialog box appears.
13. Click OK to save your data and to exit the Suboption Editor.
14. Click OK to save your data and to exit the material editor.
Note: When you are a creating a hyperelastic material for an actual analysis, you should include
data for at least three types of tests to ensure a stable material (see ``Hyperelastic behavior,''
Section 10.5.1 of the ABAQUS/Standard User's Manual and Section 9.3.1 of the
ABAQUS/Explicit User's Manual, for more details).
2-452
The Property module
you open the database, copy it to a local directory to which you can write. To determine the value
of abaqus_dir, type abaqus whereami at the operating system prompt.
Note: The path to the model database is abaqus_dir\cae\Tutorial\clamp.cae on Windows NT systems.
3. Click the File type arrow, and select Model Database (*.cae) if it is not already selected.
4. In the Selection field at the bottom of the Open Database dialog box, delete the default text and
type the path of the file containing the model database.
5. Click OK.
If you have followed any of the other Property module tutorials, a dialog box will appear asking if
you want to save the unnamed model database that contains your materials. If this dialog appears,
you can click No.
ABAQUS/CAE reads the model database containing the clamp model.
1. If you have not already entered the Property module, in the Module list located under the toolbar,
click Property.
The Property module is loaded, and the part appears in the viewport.
c. In the Type list, accept Homogeneous as the default selection and click Continue.
The solid section editor for homogeneous solids appears.
4. Click the arrow next to the Material text field to display the list of available materials. Select
Steel.
5. Accept the default Plane stress/strain thickness value, and click OK.
7. In the viewport, click the part to select the entire part. When the entire part is highlighted, click
2-453
The Property module
mouse button 2.
An Assign Section dialog box appears.
8. In the Assign Section dialog box, accept the default selection of Brick and click OK.
The section named Brick that you just created is assigned to the clamp part.
3. Click the File type arrow, and select Model Database (*.cae) if it is not already selected.
4. In the Selection field at the bottom of the Open Database dialog box, delete the default text and
type the path of the file containing the model database.
5. Click OK.
If you have followed any of the other Property module tutorials, a dialog box will appear asking if
you want to save the unnamed model database that contains your materials. If this dialog appears,
you can click No.
ABAQUS/CAE reads the model database containing the beam model.
2-454
The Property module
1. If you have not already entered the Property module, in the Module list located under the toolbar,
click Property.
The Property module is loaded and the part in the model database appears in the viewport.
c. In the Type list, accept Beam as the default selection and click Continue.
The beam section editor appears.
4. You need to create a beam profile that will be referenced by the beam section. From the main
menu bar, select Profile->Create.
The Create Profile dialog box appears.
5. Name the profile Beam, select Generalized from the Shape list, and click Continue.
The profile editor appears.
6. Enter the following data in the respective fields: Area = 20.41, I 11 = I22 = 333.33, I12 = 0, and J = 0.
(The open section properties are necessary only for sections associated with open-section beam
elements.)
8. Click Linear Properties in the Behavior field in the beam section editor.
The Beam Linear Behavior dialog box appears.
9. Enter a value of 30.E6 for the Young's modulus, 0 for the shear modulus, and click OK.
10. Accept the default value of 0 in the Section Poisson's ratio field of the beam section editor, and
click OK to save your data and to dismiss the dialog box.
12. In the viewport, drag a rectangle around the part to select the entire beam. When the entire part is
highlighted, click mouse button 2.
2-455
The Property module
13. In the Assign Section dialog box, accept the default selection of Beam and click OK.
The section named Beam that you just created is assigned to the beam part.
14. You need to assign an orientation to the beam by defining the local 1-direction. From the main
menu bar, select Assign->Beam Section Orientation.
15. In the viewport, drag a rectangle around the part to select the entire beam again. When the entire
part is highlighted, click mouse button 2.
Arrows indicating the direction cosines of the beam appear along the part edges.
16. Accept the default selection for the n1 -direction ( 0,0,-1) by clicking mouse button 2 again. (The
direction cosines of a planar beam must be (0, 0, -1).)
Triads indicating the beam orientation appear along the part edges.
· Part III, "Working with ABAQUS/CAE model databases, models, and files
· You can specify the properties of a material by selecting items from the menu bar in the material
editor and then entering the necessary data in the option definition area of the editor.
· You refer to preexisting materials when you create certain types of sections.
· You use the Assign menu to assign a section to a part or region of a part.
· You use the Assign menu to assign a beam section orientation to a part or region of a part.
2-456
The Property module
2. In the dialog box, enter the name of your choice for the material you are defining. For more
information on naming objects, see ``Using basic dialog box components,'' Section 6.3.1.
2-457
The Property module
To display information on a particular material option, click and hold that option and then press F1. A
help window appears that contains information about the parameters and data associated with the
option. If different documentation exists depending on whether you are performing an
ABAQUS/Standard or ABAQUS/Explicit analysis, a Product selection dialog box appears before the
help window; this dialog box allows you to specify the ABAQUS product (ABAQUS/Standard or
ABAQUS/Explicit) for which you want to display help.
Caution: ABAQUS/CAE does not check for missing or invalid material options until you submit
the job for analysis. (Any warnings and errors are reported by the Job module.) Therefore, you
must be careful to supply correctly all of the material options that the analysis requires.
Using the selected option list, you can add, delete, or change materials as follows:
2-458
The Property module
Select the options needed to define your material from the menus just below the selected
option list. When you select an option, its name appears in the list, and the parameters and
data associated with the option appear in the data area in the bottom portion of the editor
window. Suboptions appear beneath the corresponding primary option and are indented to
indicate their subordinate position.
2. Fill in each row with the appropriate values. For special table editing options or to read data from
an ASCII file, press mouse button 3. (For more information, see ``Entering tabular data,'' Section
6.3.5.)
2-459
The Property module
1. Change the number of field variables in the Number of field variables box to the desired value
using one of these methods:
· Click the arrows to the right of the text field to increase or decrease the number of field
variables.
Either method adds field variable columns to the table in the data area.
2. Enter the appropriate data in each cell of the table. You can enter data into the table using the
keyboard. Alternatively, you can click mouse button 3 anywhere in the table to view a list of
options for specifying tabular data. For detailed information on each option, see ``Entering tabular
data,'' Section 6.3.5.)
Note: To display context-sensitive help for specific buttons, text fields, and other options in the
Suboption Editor, you must select the option of interest and then press [F1]. (The Help menu in
the main menu bar is unavailable while the Suboption Editor is displayed.) For detailed
information on using [F1] to obtain help, see ``Displaying context-sensitive help,'' Section 5.6.1.
1. Click Suboptions in the upper right corner of the data area and select the suboption of your
choice from the list that appears.
The Suboption Editor appears in a separate dialog box.
2-460
The Property module
2. Enter the required data inside the suboption editor and then click OK to return to the material
editor.
You can enter data into a suboption table using the keyboard. Alternatively, you can click mouse
button 3 anywhere in the table to view a list of options for specifying tabular data. For example, an
option exists for creating an X-Y data object from the data in the table; you can plot the X-Y data in
the Visualization module and visually check its validity. Another option exists for automatically
entering data from a file. For detailed information on each option, see ``Entering tabular data,''
Section 6.3.5.)
1. Define a hyperelastic material. (See ``Creating a material,'' Section 15.8.1, for more information.
See also ``Selecting and modifying suboptions,'' Section 15.8.6, and ``Entering tabular data,''
Section 6.3.5, for information on including tabular experimental data in the material definition.)
Note: When you define a hyperelastic material using experimental data, you have the option
of selecting Unknown from the Strain energy potential list in the material editor. This
option allows you to define the material temporarily without specifying a particular strain
energy potential. You can use the Evaluate option to identify the optimal strain energy
potential for the material data and then display the material editor again to complete the
material definition.
2-461
The Property module
· Select Test data if you want ABAQUS to calculate the necessary strain energy
potential coefficients from the experimental data specified in the material definition.
· Select Coefficients if you want ABAQUS to use the coefficients specified in the
material definition.
b. If you selected Test data in the step above, specify the test data type or types that you
want ABAQUS to use in calculating the strain energy potential coefficients. (Only data
types for which you have specified data in the material definition appear in the list.)
4. From the list of Standard Tests, select one or more tests that you want ABAQUS to perform
using the data in the material definition. (For information on standard unit-element tests, see
``Hyperelasticity,'' Section 10.5 of the ABAQUS/Standard User's Manual and Section 9.3 of the
ABAQUS/Explicit User's Manual.)
5. For each test that you select, enter a Nominal Strain value that will be the upper or lower limit for
the analysis. (Enter a positive value for a tension test, or enter a negative value for a compression
test.)
· If you selected Test data as a data source, a list of all the available strain energy potentials
appears. From the list, select one or more that you want ABAQUS to apply to the experimental
data.
· If you selected Coefficients as a data source, the name of the strain energy potential specified
in the material definition appears. You can simply review the information and move on to the
next step.
2-462
The Property module
· ``Hyperelasticity,'' Section 10.5 of the ABAQUS/Standard User's Manual and Section 9.3 of the
ABAQUS/Explicit User's Manual
· ``Selecting a method for defining the temperature variation through the section, '' Section 15.9.3
· ``Specifying the number of section integration points in a homogeneous shell section, '' Section
15.9.4
You create sections by entering data in the section editor. The format of the editor varies according to
the type of section you are defining.
Detailed instructions for creating a section:
2. Enter a section name of your choice. For more information on naming objects, see ``Using basic
dialog box components,'' Section 6.3.1.
2-463
The Property module
4. In the editor, enter all of the data necessary to define the section and then click OK.
Note: You can display help on particular aspects of an editor by selecting Help->On Context from the main menu bar and then
clicking the editor feature of interest.
· ``Shell section behavior,'' Section 15.6.4 of the ABAQUS/Standard User's Manual and Section
14.4.3 of the ABAQUS/Explicit User's Manual
· ``Beam section behavior,'' Section 15.3.5 of the ABAQUS/Standard User's Manual and Section
14.3.5 of the ABAQUS/Explicit User's Manual
If a shell section is integrated before the analysis, the temperature must be constant through
2-464
The Property module
the section. You can use the Load/BC/IC module to specify the initial temperature of the
section. For more information, see ``Defining a constant initial temperature through a shell
section,'' Section 19.7.15.
If you select this method for defining temperature variation through the section, you can use
the Load/BC/IC module to specify the initial temperature at the reference surface (for shells)
or cross-section origin (for beams) and the temperature gradient or gradients through the
section. For more information, see ``Defining an initial temperature gradient through a shell
section,'' Section 19.7.17, and ``Defining initial temperature gradients through a beam
section,'' Section 19.7.18.
If you select this method for defining temperature variation, you must enter the number of
temperature points (values) through the section in the text field provided. You can use the
Load/BC/IC module to specify the temperature at each of these points. For more information,
see ``Defining initial temperatures at points through a shell or beam section, '' Section 19.7.16.
The shape of the profile that you specify in the beam section definition determines the number
and location of the temperature points. (For more information on temperature points, see
``Beam cross-section library,'' Section 15.3.9 of the ABAQUS/Standard User's Manual and
Section 14.3.8 of the ABAQUS/Explicit User's Manual.) If you select this method, you can use
the Load/BC/IC module to specify the temperature at each of these points. For more
information, see ``Defining initial temperatures at points through a shell or beam section, ''
Section 19.7.16.
· ``Defining initial temperatures at points through a shell or beam section, '' Section 19.7.16
· ``Specifying temperature and field variables'' in ``Using the *SHELL SECTION option to define
the section behavior,'' Section 15.6.5 of the ABAQUS/Standard User's Manual and Section 14.4.4
of the ABAQUS/Explicit User's Manual
· ``Specifying temperature and field variables'' in ``Using the *BEAM SECTION option to define
the section behavior,'' Section 15.3.6 of the ABAQUS/Standard User's Manual and Section 14.3.6
of the ABAQUS/Explicit User's Manual
2-465
The Property module
3. Click either the upward or downward arrow in the Thickness integration points text field to
change the default number to the number of your choice.
If you are using the Simpson integration rule, you can specify only odd numbers ranging from 3 to
15. If you are using the Gauss integration rule, you can specify odd or even numbers ranging from
2 to 7.
You can also type the number directly in the text field.
· ``Defining the shell section integration'' in ``Using the *SHELL SECTION option to define the
section behavior,'' Section 15.6.5 of the ABAQUS/Standard User's Manual and Section 14.4.4 of
the ABAQUS/Explicit User's Manual
2-466
The Property module
Tip: You can also click Create in the Profile Manager or select the create profile tool
in the Property module toolbox.
2. Enter a profile name of your choice. For more information on naming objects, see ``Using basic
dialog box components,'' Section 6.3.1.
2. In the dialog box, enter the local x1 - and x2 -coordinates for the centroid and/or the shear center as
desired.
3. Click OK.
2-467
The Property module
· *CENTROID
· *SHEAR CENTER
2. In the dialog box, enter the name of the skin you are defining and click Continue. For more
information on naming objects, see ``Using basic dialog box components,'' Section 6.3.1.
· If desired, select the datum coordinate system representing the material orientation. The
1-direction of the material is aligned with the X-axis of the coordinate system specified. You
can select a datum coordinate system from the viewport or select the global coordinate system.
For more information, see ``Assigning a material orientation to a shell or solid part or region, ''
2-468
The Property module
Section 15.11.3.
· If desired, enter an offset from the selected face or faces. The offset can be negative or
positive. A negative offset from a shell or an axisymmetric part indicates on which side the
skin is positioned. A negative offset from a solid indicates that the skin is embedded in the
solid.
5. Click OK to create the skin and to close the Skin editor dialog box.
2. Enter a name for the set in the Create Set dialog box that appears.
4. Click on the list of filters, and select Skins. ABAQUS/CAE now allows you to select only skins
from the viewport. You cannot select vertices, edges, faces, or cells.
5. Select the skin from the viewport, and click mouse button 2 to indicate that you have finished
selecting skins.
After you create the set that refers to the skin, you then select the set by clicking the Sets button
from the right side of the prompt area and select from the list of named sets.
· ``Assigning a material orientation to a shell or solid part or region, '' Section 15.11.3
· ``Displaying information about section assignment and orientations for a particular region, ''
Section 15.11.4
2-469
The Property module
Note: When you import an orphan mesh part from an input file, some section properties
associated with that orphan mesh may also be imported; in these cases it may be unnecessary to
assign section properties to the part. For more information, see ``Importing models from
ABAQUS/Standard and ABAQUS/Explicit input files,'' Section 13.4.
1. If the part to which you want to assign a section is not visible in the current viewport, click the
name of the desired part in the Part list located under the toolbar.
The part that you select appears in the current viewport.
Tip: You can also click the tool in the Property module tool box.
3. Select the part or region of the part from the viewport and click mouse button 2 to indicate you
have finished selecting. (For more information, see Chapter 9, "Selecting objects within the
viewport".)
Tip: You can limit the types of objects that you can select in the viewport by clicking the
selection filter tool in the prompt area and then clicking the selection filter of your
choice in the dialog box that appears. See ``Using the selection options,'' Section 9.3, for more
information.
If you would rather select from a list of existing sets, do the following:
An Assign Section dialog box appears. This dialog box contains a list of existing sections that
can be assigned to the selected region or part set. For example, if you selected a solid region, any
existing solid sections appear in the Assign Section dialog box.
4. In the Assign Section dialog box, select the section of interest and click OK.
ABAQUS/CAE assigns the selected section to the part or region.
5. If the part contains more than one region, repeat Steps 3 and 4. When you have finished assigning
sections to the regions of the part, use one of the following methods to exit the section assignment
2-470
The Property module
mode:
· If you are selecting regions of the part from the viewport, click mouse button 2 or the cancel
button on the left side of the prompt area.
· If you are selecting preexisting sets from the Region Selection dialog box, click Cancel.
1. If the part to which you want to assign an orientation is not visible in the current viewport, click
the name of the desired part in the Part list located under the toolbar.
The selected part appears in the current viewport.
Tip: You can also click the tool in the Property module tool box.
3. Select the wire part or a wire region of the part from the viewport and click mouse button 2 to
indicate you have finished selecting. (For more information, see Chapter 9, "Selecting objects
within the viewport".)
Tip: You can limit the types of objects that you can select in the viewport by clicking the
selection filter tool in the prompt area and then clicking the selection filter of your
choice in the dialog box that appears. See ``Using the selection options,'' Section 9.3, for more
information.
If you would rather select from a list of existing sets, do the following:
2-471
The Property module
part sets. Part sets containing only wires appear in the list.
4. ABAQUS/CAE prompts you to enter the vector representing an approximate n1 -direction (the
local 1-direction of the cross-section). For more information on defining the n1 -direction, see
``Beam element cross-section orientation,'' Section 15.3.4 of the ABAQUS/Standard User's
Manual and Section 14.3.4 of the ABAQUS/Explicit User's Manual.
Note: If the part was created in two-dimensional modeling space, the n1 -direction is always normal to the X-Y plane (0.0, 0.0,
-1.0).
ABAQUS/CAE displays the resulting (n1 , n2 , t) axis system on the selected wire regions.
5. If the displayed (n1 , n2 , t) axis system is correct, click OK in the prompt area to confirm your
choice. If you wish to change the beam orientation, click the backup button ( ) and enter a new
n1 -direction.
6. If you wish to assign beam orientations to additional wire regions, repeat Steps 3 through 5.
7. Click mouse button 2 to indicate you have finished assigning beam orientations.
1. If the part to which you want to assign a material orientation is not visible in the current viewport,
click the name of the desired part in the Part list located under the toolbar.
2-472
The Property module
Tip: You can also click the tool in the Property module tool box.
3. Select the shell or solid part or part region from the viewport and click mouse button 2 to indicate
you have finished selecting. (For more information, see Chapter 9, "Selecting objects within the
viewport.")
Tip: You can limit the types of objects that you can select in the viewport by clicking the
selection filter tool in the prompt area and then clicking the selection filter of your
choice in the dialog box that appears. See ``Using the selection options,'' Section 9.3, for more
information.
If you would rather select from a list of existing sets, do the following:
4. In the viewport, select the datum coordinate system defining the material orientation that you want
to apply to the region. (See ``Controlling datum display,'' Section 46.6, for information about
displaying datum geometry in the viewport.)
Note: From the right side of the prompt area, click Use Global CSYS to reset a previously assigned material orientation back
to the global coordinate system and click OK to confirm your choice.
If you are assigning a material orientation to a shell region, you are prompted to specify the axis of
the datum coordinate system that is normal to the shell. In the prompt area, click the button that
indicates the axis of your choice.
5. If the datum coordinate system that you selected is a cylindrical or spherical system, you have the
option of specifying an additional rotation about a specific local axis (for solids) or about the shell
normal (for shells). (You specify the equivalent rotation in rectangular coordinate systems directly
in the coordinate system definition.) If necessary, specify information concerning the additional
rotation:
a. If you are assigning a material orientation to a solid, you are prompted to specify the
coordinate system axis about which the additional rotation occurs. In the prompt area,
click the button that indicates the axis of your choice.
2-473
The Property module
b. Enter the additional rotation in the prompt area, and click mouse button 2.
6. If the axis system displayed in the viewport is correct, click OK in the prompt area to confirm your
choice. If you want to change the orientation, click the backup button ( ) and change the
orientation as necessary.
· ``Solid (continuum) elements,'' Section 14.1.1 of the ABAQUS/Standard User's Manual and
Section 13.1.1 of the ABAQUS/Explicit User's Manual
· ``Shell elements: overview,'' Section 15.6.1 of the ABAQUS/Standard User's Manual and Section
14.4.1 of the ABAQUS/Explicit User's Manual
· The material orientations assigned to all or selected shell and solid regions.
Tip: You can also query the model by clicking the tool in the toolbar.
ABAQUS/CAE displays the Query dialog box.
You can request either a general query or a module-specific query. For a discussion of the
information displayed by general queries, see ``Obtaining general information about the model,''
Section 44.2.2. The Section assignments , Beam orientations, and Material orientations
queries are specific to the Property module.
2. From the Property Queries list, select the property of interest; then click Apply.
2-474
The Property module
· Click Single region if you want to query only one region of the part. Then select the region in
the viewport that you want to query. (For more information, see Chapter 9, "Selecting objects
within the viewport.")
Tip: You can limit the types of objects that you can select in the viewport by clicking the
selection filter tool in the prompt area and then clicking the selection filter of your
choice in the dialog box that appears. See ``Using the selection options,'' Section 9.3, for
more information.
· Click All regions if you want to query all regions of the part.
4. Once you have specified the regions that you want to query, the following information appears:
5. In the prompt area, click Query Again to query another region of the part.
6. To exit the querying procedure, click the cancel button in the prompt area.
2-475
The Assembly module
· ``Understanding the relationship between parts, part instances, and assemblies, '' Section 16.3
3-476
The Assembly module
To exit the Assembly module, select any other module from the Module list. You need not save your
assembly before exiting the module; it will be saved automatically when you save the entire model by
selecting File->Save or File->Save As from the main menu bar.
1. You create a part in the Part module; each part is a distinct geometric entity that can be modified
and manipulated independently of other parts. Parts exist in their own coordinate system and have
no knowledge of other parts.
2. You define section properties in the Property module and also associate a material with a section.
You use the Property module to assign these section properties to a part or to a selected region of a
part.
3. You create instances of your parts in the Assembly module, and you position those instances
relative to each other in a global coordinate system to form the assembly. An instance always
maintains its association with the original part; although you cannot modify a part instance
directly, you can modify the original part in the Part module. ABAQUS/CAE will then update any
instances of that part when you return to the Assembly module. You can instance a part many
times and assemble multiple instances of the same part. Each instance of the part is associated with
the section properties assigned to the part in the Property module.
4. You use the Interaction, Load/BC/IC, and Mesh modules to complete the definition of the model
by applying items such as loads, boundary conditions, and a mesh to the assembly.
``Creating a part instance,'' Section 16.7.2, contains detailed instructions on creating part instances.
· ``How conflicts can arise between position constraints, '' Section 16.4.3
3-477
The Assembly module
Auto-offset
When you create the first part instance in the Assembly module, ABAQUS/CAE displays a
triad indicating the origin and the orientation of the global coordinate system. ABAQUS/CAE
positions the first part instance so that the origin of the part aligns with the origin of the global
coordinate system and the axes are aligned. If you create additional part instances,
ABAQUS/CAE continues to position the new instances such that their coordinate system
aligns with the global coordinate system. Since this usually results in new part instances
overlapping existing ones, ABAQUS/CAE allows you to apply an offset before it creates the
instance. The offset is applied along the X-axis for three-dimensional and two-dimensional
part instances and along the Y-axis for axisymmetric part instances.
· You can translate a selected part instance along a vector. You specify the X-, Y-, and
Z-coordinates of the start point and end point of the translation vector.
· You can rotate a selected part instance about an axis. You specify the X-, Y-, and
Z-coordinates of the start point and end point of the axis of rotation and the angle of
rotation.
· You can replace a part instance with a second part instance. ABAQUS/CAE positions the
new part instance such that its origin is located at the origin of the original part instance,
and their axes align. In addition, you can choose whether the new part instance inherits all
the constraints from the instance it replaced. Replacing a part instance is useful when you
are replacing a part instance with one that has similar geometry. For example, the new part
instance might have additional detail that was not present in the original part instance.
Creating the final assembly is an iterative process of creating part instances, applying position
constraints, and applying translations and rotations. After each repositioning, ABAQUS/CAE displays
3-478
The Assembly module
a temporary image indicating the result of the operation. You can accept the new position, cancel the
operation, or step back through the repositioning procedure by clicking the go back button in the
prompt area.
You can use the Query toolset to obtain the coordinates of a vertex and to measure the distance
between selected vertices. This may help you determine the vector along which you need to translate a
part instance or the angle through which to need to rotate it. ``Using the Query toolset to query the
assembly,'' Section 16.9, contains detailed instructions on how to obtain information about the
assembly.
· Edge to edge
· Contact
In general, applying a single position constraint is not sufficient to define the precise location of the
movable part instance. You must apply several position constraints--usually three for a
three-dimensional assembly and two for a two-dimensional assembly--to position a part instance in the
desired location. Part instances can overlap as a result of applying position constraints; ABAQUS/CAE
does not prevent overclosure between edges, faces, or cells. Similarly, ABAQUS/CAE does not
prevent you from overconstraining part instances or duplicating a constraint.
The definition of a constraint feature includes all the faces and edges that you originally selected. If
you subsequently modify a part or move a part instance, ABAQUS/CAE automatically recalculates the
constraint based on your original selection of faces and edges. As a result, one or more part instances
may move after the assembly is regenerated. For example, different edges may become parallel and
different faces may come into contact. For more information on features, see ``Manipulating features in
the Assembly module,'' Section 16.5.2, and Chapter 42, "The Feature Manipulation toolset."
The following position constraints are provided by the Assembly module:
Parallel Face
A parallel face position constraint causes the two selected faces or datum planes to become
parallel. However, the position constraint does not specify the precise location of the part
3-479
The Assembly module
instances, and the distance between the parallel faces is arbitrary. To apply a parallel face
position constraint between two part instances, you do the following:
· Select the faces or datum planes to be constrained to be parallel from the movable part
instance and the fixed part instance, as shown in Figure 16-1.
· ABAQUS/CAE displays arrows normal to the selected faces. You prescribe the
orientation of the movable part instance by selecting the direction of the arrow normal to
its selected face. Figure 16-2 illustrates the result of applying the position constraint and
the effect on the movable part instance of reversing the direction of the arrow.
Figure 16-2 The result of applying a parallel face position constraint and the effect of
changing the direction of the arrow normal to the selected face of the movable part
instance.
3-480
The Assembly module
ABAQUS/CAE rotates the movable part instance about its centroid until the two selected
faces are parallel and the arrows are pointing in the same direction.
The faces you select from the movable and fixed part instances must be planar. The parallel
face position constraint can be applied only to three-dimensional part instances.
Face to Face
A face-to-face position constraint is similar to a parallel face position constraint except that
you define the clearance between the parallel faces. The clearance is measured between the
two selected faces, positive along the normal to the fixed part instance. Other than this
clearance, the precise location of the movable part instance is not constrained. Assuming that
you selected the same two faces shown in Figure 16-1, the effect of applying a face-to-face
constraint is shown in Figure 16-3. Figure 16-3 also illustrates the effect on the movable part
instance of reversing the direction of the arrow normal to its selected face.
Figure 16-3 The result of applying a face-to-face constraint and the effect of changing the
direction of the arrow normal to the selected face of the movable part instance.
3-481
The Assembly module
ABAQUS/CAE rotates the movable part instance until the two selected faces are parallel and
the arrows point in the same direction. In addition, the movable part instance is translated to
satisfy the clearance specified. The faces you select from the movable and fixed part instances
must be planar. The face-to-face position constraint can be applied only to three-dimensional
part instances.
Parallel Edge
A parallel edge position constraint causes two selected edges or datum axes to become
parallel. However, the position constraint does not specify the precise location of the part
instances, and the distance between the parallel edges is arbitrary. To apply a parallel edge
position constraint between two part instances, you do the following:
· Select the edges or datum axes to be constrained to be parallel from the movable and fixed
part instance, as shown in Figure 16-4.
3-482
The Assembly module
· ABAQUS/CAE displays arrows along the selected edges. You prescribe the orientation of
the movable part instance by selecting the direction of the arrow along its selected edge.
Figure 16-5 illustrates the result of applying the position constraint and the effect on the
movable part instance of reversing the direction of the arrow.
Figure 16-5 The result of applying a parallel edge constraint and the effect of changing
the direction of the arrow along the selected edge of the movable part instance.
ABAQUS/CAE rotates the movable part instance until the two selected edges are parallel
and the arrows point in the same direction.
The edges you select from the movable and fixed part instances must be straight. The parallel
edge position constraint can be applied only to two-dimensional and three-dimensional part
instances. It has no effect on axisymmetric part instances.
Edge to Edge
An edge-to-edge position constraint is similar to a parallel edge position constraint except that
the clearance between the parallel edges is defined by the constraint. Assuming that you
selected the same two edges shown in Figure 16-4, the effect of applying an edge-to edge
position constraint to a two-dimensional assembly is shown in Figure 16-6. Figure 16-6 also
illustrates the effect on the movable part instance of reversing the direction of the arrow along
its selected edge.
Figure 16-6 The result of applying an edge-to-edge constraint and the effect of changing the
3-483
The Assembly module
direction of the arrow along the selected edge of the movable part instance.
The modeling space of the assembly determines the behavior of ABAQUS/CAE after you
apply an edge-to-edge position constraint.
· If the assembly is two-dimensional, you can specify the clearance between the selected
edges. The clearance is measured between the two selected faces, positive along the
normal to the fixed part instance.
Other than this behavior, the precise location of the movable part instance is not constrained.
The edges you select from the movable and fixed part instances must be straight. The
edge-to-edge position constraint can be applied to two-dimensional, three-dimensional, and
axisymmetric part instances; however, axisymmetric part instances can move only parallel to
the axis of revolution.
Coaxial
A coaxial position constraint causes the two selected cylindrical or conical faces to become
coaxial but does not constrain their precise location. To apply a coaxial position constraint
between two part instances, you do the following:
· Select the cylindrical or conical faces to be constrained to be coaxial from the movable
and fixed part instance, as shown in Figure 16-7.
3-484
The Assembly module
· ABAQUS/CAE displays arrows along the axis of revolution of the selected part instances.
You prescribe the orientation of the movable part instance by selecting the direction of the
arrow along its axis of revolution. Figure 16-8 illustrates the result of applying the coaxial
position constraint.
ABAQUS/CAE rotates and translates the movable part instance until the two selected faces
are coaxial and the arrows are pointing in the same direction. The coaxial position constraint
can be applied only to three-dimensional part instances.
Contact
A contact position constraint causes selected faces or edges to come into contact by translating
the movable part instance along a selected vector. This type of constraint is available only for
3-485
The Assembly module
native or imported geometric part instances. Unlike other constraints, a contact position
constraint specifies the final location of the movable part instance.
When applying a contact position constraint between part instances in three-dimensional
modeling space, you select faces to come into contact; for part instances in two-dimensional or
axisymmetric modeling space, you select edges to come into contact. In addition, when the
contact position constraint is applied between axisymmetric part instances, the translation
vector must be parallel to the axis of revolution.
ABAQUS/CAE approximates a curved face with a set of faceted faces. Likewise,
ABAQUS/CAE approximates a curved edge with a set of faceted edges. The number of facets
depends on the degree of curve refinement that you specified when creating the part in the Part
module. Use the box zoom tool to view the faceting applied to curved faces or edges in
the assembly. When you are defining contact between curved faces or curved edges,
ABAQUS/CAE computes the contact position using this faceted representation. By default,
the curve refinement is set to Medium. You may wish to set the curve refinement to Fine or
Extra Fine for curved faces or edges that you know will be coming into contact. For more
information, see ``Controlling curve refinement,'' Section 46.4.
When creating a contact position constraint, you can select more than one face or edge from
both the fixed and the movable part instances. Selecting multiple faces or edges is useful if
you are not sure what part of the model will come in contact when the movable part instance
moves along the selected vector. However, for faster processing you should select as few faces
or edges as possible.
Even though you apply a contact position constraint to two part instances, the physical
proximity of the selected surfaces is not enough to indicate any type of interaction between
them. You must use the Interaction module to specify mechanical contact between surfaces.
The contact position constraint is satisfied only within a tolerance based on the size of your
model. As a result, contact may not be precise unless it is applied between two planar surfaces.
A contact position constraint often conflicts with other position constraints and will break
those constraints if applied. If possible, you should not mix a contact position constraint with
other position constraints.
To define a contact position constraint between two part instances, you do the following:
· Select faces or edges from the part instance that will move and from the part instance that
will remain stationary.
· Prescribe the motion of the movable part instance by defining a translation vector. Figure
16-9 illustrates the selected edges and translation vector.
Figure 16-9 Select the edges to contact and define the translation vector.
3-486
The Assembly module
· Define the desired clearance between the selected faces or edges. Figure 16-10 shows the
effect of the contact constraint after specifying a clearance value of zero and a clearance
value of d.
Figure 16-10 The effect of applying a contact constraint and specifying clearance values
of zero and d.
To measure the clearance d, ABAQUS/CAE first moves the part instance along the
translation vector until any pair of selected faces or edges come into contact.
ABAQUS/CAE then moves the part instance along the translation vector a distance
specified by the clearance value. The clearance can be zero or a positive or negative
number; a negative value for the clearance results in overclosure between the selected
faces or edges. When you apply a contact constraint, ABAQUS/CAE calculates the
position of the movable part instance within a tolerance based on its size. If you want to
avoid any possibility of overclosure, you should specify a small clearance value, rather
3-487
The Assembly module
· Remove all existing position constraints without changing the position of the part instances and
then apply the translation or rotation.
3-488
The Assembly module
Figure 16-11 An edge-to-edge constraint applied between a datum axis and a selected edge.
In contrast, Figure 16-12 illustrates an edge-to-edge position constraint applied between three movable
part instances and a fixed datum axis that provides reference geometry. In this example the datum axis
was created along the X-axis of the assembly and is not associated with any part instance.
3-489
The Assembly module
Figure 16-12 Edge-to-edge constraints applied between multiple parts and a fixed datum axis.
Applying three edge-to-edge position constraints, one to each of the three part instances shown, would
result in alignment of the three instances along the datum axis.
A datum is a feature of the assembly and is regenerated along with the rest of the assembly. You can
make datum geometry invisible while still retaining it in the assembly by selecting View->Assembly
Display Options from the main menu bar. For more information, see ``Controlling datum display,''
Section 46.6.
The triad indicating the origin and the orientation of the global coordinate system is a datum
coordinate system created by the Assembly module. You can suppress or delete it, but you cannot
modify it.
Part instances
You can suppress, resume, and delete part instances. You can partition a part instance, but you
cannot edit its geometry. To modify a part instance, you must edit the original part in the Part
3-490
The Assembly module
Position constraints
You can edit, suppress, resume, and delete position constraints. You can modify the following
parameters of a position constraint:
· The direction of the arrow normal to the selected face or along the selected edge of the
movable part instance.
· The clearance between the selected face or edge of the movable part instance and the
selected face or edge of the fixed part instance. The clearance parameter applies only to
face-to-face, edge-to-edge, and contact constraints.
Translations and rotations are not stored as features and cannot be edited, suppressed,
resumed, or deleted.
When the Feature Manipulation toolset asks you to select a feature, you can select visible features such
as a part instance, a datum, or a partition from the viewport. However, to select a position constraint,
you must click the Feature List button on the right side of the prompt area and select the position
constraint from the Feature List dialog box that appears.
The following feature manipulation tools are available from the Feature Manipulation toolset:
Edit
When you edit a feature, ABAQUS/CAE displays the Feature Modify dialog box, and you can
modify the feature's parameters or the sketch that defined the feature. You cannot edit part
instances; you must return to the Part module to modify the original part.
Suppress
Suppressing a feature temporarily removes it from the definition of the assembly. A
suppressed feature is invisible, cannot be meshed, and is not included in the analysis of the
model. Suppressing a parent feature will suppress all of its child features.
Resume
Resuming a feature restores a suppressed feature to the assembly; resuming a parent feature
restores all of its child features. You can choose to resume all features, the set of features most
recently suppressed, or just a selected feature.
Delete
Deleting a feature removes it from the assembly; you cannot restore a deleted feature.
3-491
The Assembly module
For a more detailed explanation of the Feature Manipulation toolset, see Chapter 42, "The Feature
Manipulation toolset."
· Origin
For more information, see ``Using the Query toolset to query the assembly,'' Section 16.9.
3-492
The Assembly module
analysis; for example, selected vertices or faces. Assembly sets can include regions from multiple part
instances. Part sets, which are created by selecting geometry from a part in the Part module or the
Property module, are not transferred to instances of the part in the Assembly module.
You use the Surface toolset to create surfaces from regions of the assembly. Surfaces are more
specialized than sets. While sets can be used for many different applications, surfaces can be used only
where an operation requires you to identify a surface in the physical model. Such operations include
applying distributed loads, such as pressure loads, and defining contact interactions.
To see a tooltip containing a brief definition of an Assembly module tool, hold the mouse over the tool
for a moment. For information on using toolboxes and selecting hidden icons, see ``Using toolboxes
that contain hidden icons,'' Section 6.4.2.
3-493
The Assembly module
· Create instances of parts in the model and add them to the assembly. The part can be either a
native part, an ACIS, IGES or VDA-FS part, or an orphan mesh.
· Rotate selected part instances through a specified angle about a specified axis.
You may find it more convenient to access the instance tools using the Assembly module toolbox. For
a diagram of the tools in the Assembly toolbox, see ``Using the Assembly module toolbox,'' Section
16.6.
3-494
The Assembly module
When you create an instance of a part, by default ABAQUS/CAE positions the instance so that the
origin of the original geometry aligns with the origin of the assembly coordinate system. When you
create multiple part instances, a new instance can be positioned over an existing instance. However, if
you toggle on Auto-offset from other instances in the Create Instance dialog box, ABAQUS/CAE
translates each new part instance along the X-axis until it does not overlap any existing part instances.
If the assembly is axisymmetric, ABAQUS/CAE translates the new part instance along the axis of
revolution instead of along the X-axis.
Detailed instructions for creating a part instance:
1. From the main menu bar, select Instance->Create to create a part instance from the parts in the
model.
ABAQUS/CAE displays the Create Instance dialog box and a list of all the existing parts in the
model.
Tip: You can also create a part instance using the tool from the Assembly module
toolbox. For a diagram of the tools in the Assembly toolbox, see ``Using the Assembly module
toolbox,'' Section 16.6.
2. From the list of parts, select the parts to instance. You can use a combination of [Ctrl]+Click and
[Shift]+Click to select multiple parts.
A temporary image of the selected part instances appears in the current viewport. ABAQUS/CAE
positions the temporary images so that their origins coincide with the origin of the global
coordinate system.
3. If desired, toggle on Auto-offset from other instances to offset the new part instances.
4. If you are satisfied that you have selected the correct part instances, click Apply from the Create
Instance dialog box.
5. To create additional part instances, repeat this procedure from Step 2. When you have finished
creating part instances, click Cancel to close the Create Instance dialog box.
· ``Understanding the relationship between parts, part instances, and assemblies, '' Section 16.3
3-495
The Assembly module
Select Instance->Translate from the main menu bar to move a selected part instance along a selected
vector. The direction and magnitude of the vector are arbitrary except that you can translate
axisymmetric part instances only along the axis of rotation. Translating a part instance may invalidate a
previous position constraint; for example, a constraint that aligns two faces. If you proceed with the
translation, ABAQUS/CAE first converts all previous position constraints to an absolute position.
When you create the first part instance, ABAQUS/CAE displays a graphic indicating the origin and
orientation of the assembly's default coordinate system. You can use this graphic to help you decide
how to translate your part instances. In addition, you can use the Query toolset to review the sum of the
translations and rotations previously applied to a part instance and the distance between selected
vertices. Translations and rotations are not considered features of the assembly and cannot be edited or
deleted.
Detailed instructions for translating a part instance:
Tip: You can also translate a part instance using the tool from the Assembly module
toolbox. For a diagram of the tools in the Assembly toolbox, see ``Using the Assembly module
toolbox,'' Section 16.6.
ABAQUS/CAE displays prompts in the prompt area to guide you through the procedure.
2. Select the part instance to translate. If the selection is ambiguous, you can cycle through the
candidate instances using the buttons in the prompt area. You can also click the Instance List
button on the right of the prompt area and select the instance to translate from the Feature List
dialog box that appears.
ABAQUS/CAE highlights the selected part instance.
3. If the translation could break any previous position constraints, you must choose whether to
continue the translation from the dialog box that appears. Choose one of the following:
Yes
Continue the translation and convert the constraints to an absolute position before
applying the translation.
No
Abort the translation.
4. Select the start point of the translation vector. You can select any existing vertices or datum points,
or you can enter the coordinates in the text box in the prompt area.
5. Select the end point of the translation vector. Again, you can select any existing vertices or datum
points, or you can enter the coordinates in the text box in the prompt area.
3-496
The Assembly module
ABAQUS/CAE displays a temporary image indicating the translation that will be applied to the
selected part instance. You cannot edit or delete a translation after it is applied.
a. If you are satisfied the translation is correct, click the OK button in the prompt area.
ABAQUS/CAE translates the part instance and positions it at the same location as the
temporary image of the part instance.
b. If you are not satisfied with the translation, click the go back button ( ) and specify a
new translation vector.
Tip: You can also rotate a part instance using the tool from the Assembly module
toolbox. For a diagram of the tools in the Assembly toolbox, see ``Using the Assembly module
toolbox,'' Section 16.6.
3-497
The Assembly module
ABAQUS/CAE displays prompts in the prompt area to guide you through the procedure.
2. From the assembly, select the part instance to rotate. If the selection is ambiguous, you can cycle
through the candidate instances using the buttons in the prompt area. You can also click the
Instance List button on the right of the prompt area and select the instance to rotate from the
Feature List dialog box that appears.
3. If the rotation could break any previous constraints, you must choose whether to continue the
rotation from the dialog box that appears. Choose one of the following:
Yes
Continue the rotation and convert the constraints to an absolute position before applying
the rotation.
No
Abort the rotation.
4. Select the start point of the vector that defines the axis of rotation. You can select any existing
vertices or datum points, or you can enter the coordinates in the text box in the prompt area.
5. Select the end point of the vector that defines the axis of rotation. Again, you can select any
existing vertices or datum points, or you can enter the coordinates in the text box in the prompt
area.
6. In the text box that appears in the prompt area, type the angle of rotation. A positive angle
indicates a counterclockwise rotation; a negative angle indicates a clockwise rotation.
ABAQUS/CAE displays a temporary image indicating the rotation that will be applied to the
selected part instance. You cannot edit or delete a rotation after it is applied.
a. If you are satisfied that the rotation is correct, click the OK button in the prompt area.
ABAQUS/CAE rotates the part instance and positions it at the same location as the
temporary image of the part instance.
b. If you are not satisfied with the rotation, click the go back button ( ) and specify a new
rotation.
3-498
The Assembly module
1. From the main menu bar, select Instance->Replace to replace a selected part instance.
2. From the assembly, select the part instance to replace. If the selection is ambiguous, you can cycle
through the candidate instances using the buttons in the prompt area. You can also click the
Instance List button on the right of the prompt area and select the instance from the Feature List
dialog box that appears.
ABAQUS/CAE displays the Replace Instance dialog box with a list of all the parts in the model.
3. From the Replace Instance dialog box, select the part that will replace the selected part instance
in the assembly.
ABAQUS/CAE displays a temporary image of the new part instance in the assembly and positions
it so that its origin is located at the origin of the original part instance and their axes align.
4. If the correct part instance is selected, click OK in the Replace Instance dialog box.
If you have not applied any position constraints to the original part instance, ABAQUS/CAE
replaces it with the new part instance.
5. If you have applied position constraints to the original part instance, you must choose one of the
following buttons in the prompt area:
· Click OK to position the new part instance in the same location as the instance it is replacing.
ABAQUS/CAE removes any constraints that were applied to the original instance, while
maintaining its position.
· Click Apply previous constraints if you want the new part instance to inherit position
constraints from the part instance being replaced. ABAQUS/CAE applies all the previous
constraints that can be satisfied by the new part instance; any constraints that cannot be
3-499
The Assembly module
ABAQUS/CAE replaces the original part instance with the new part instance.
· ``Understanding the relationship between parts, part instances, and assemblies, '' Section 16.3
· ``Constraining two part instances with parallel planar faces, '' Section 16.8.2
· ``Constraining two part instances with parallel planar faces separated by a specified distance, ''
Section 16.8.3
· ``Constraining two part instances with parallel edges, '' Section 16.8.4
· ``Constraining two part instances with parallel edges separated by a specified distance, '' Section
16.8.5
· ``Constraining two part instances with coaxial faces, '' Section 16.8.6
· ``Constraining two part instances with contact between two faces separated by a specified
distance,'' Section 16.8.7
· Parallel Face. Positions a selected face of a movable part instance parallel to a selected face of a
fixed part instance.
· Face to Face. Positions a selected face of a movable part instance parallel to and a specified
distance away from a selected face of a fixed part instance.
· Parallel Edge. Positions a selected edge of a movable part instance parallel to a selected edge of a
fixed part instance.
3-500
The Assembly module
· Edge to Edge. Positions a selected edge of a movable part instance parallel to and a specified
distance away from a selected edge of a fixed part instance.
· Coaxial. Positions the axis of revolution of a selected face of a movable part instance coincident
with the axis of revolution of a selected face of a fixed part instance.
· Contact. Positions two part instances by moving one instance along a vector defining the direction
of motion until one of its selected faces is a specified distance from one of the selected faces of the
fixed instance.
Constraints position one part instance relative to another; as a result, constraints cannot be applied
until your assembly contains two or more part instances.
You may find it more convenient to access the constraint tools using the Assembly module toolbox.
For a diagram of the tools in the Assembly toolbox, see ``Using the Assembly module toolbox,''
Section 16.6.
Tip: You can also apply the parallel face constraint using the tool in the Assembly
module toolbox. For a diagram of the tools in the Assembly toolbox, see ``Using the Assembly
module toolbox,'' Section 16.6.
ABAQUS/CAE displays prompts in the prompt area to guide you through the procedure.
2. Select planar faces from three-dimensional part instances, as shown in the following figure:
3-501
The Assembly module
· Click OK to accept the direction of the arrow on the face of the movable instance.
· Click Flip to reverse the direction of the arrow on the face of the movable instance, and click
OK.
ABAQUS/CAE positions the movable part instance so that the two faces are parallel and the
arrows point in the same direction. The effect of changing the direction of the arrow is illustrated
in the following figure:
If the parallel face constraint conflicts with existing constraints, ABAQUS/CAE displays an error
message and cancels the operation. To avoid the conflict, you can try reversing the selection of the
part instance that will move and the part instance that will remain fixed. Alternatively, you can
convert the existing constraints to an absolute position and reapply the parallel face constraint.
3-502
The Assembly module
Tip: You can also apply the face-to-face constraint using the tool in the Assembly
module toolbox. For a diagram of the tools in the Assembly toolbox, see ``Using the Assembly
module toolbox,'' Section 16.6.
ABAQUS/CAE displays prompts in the prompt area to guide you through the procedure.
2. Select planar faces from two three-dimensional part instances, as shown in the following figure:
3-503
The Assembly module
· Click OK to accept the direction of the arrow on the face of the movable instance.
· Click Flip to reverse the direction of the arrow on the face of the movable instance, and click
OK.
The effect of changing the direction of the arrow is illustrated in the next step.
4. In the text field that appears in the prompt area, enter the distance between the selected faces,
positive along the normal to the face of the fixed instance.
ABAQUS/CAE positions the movable part instance so that the two faces are parallel and the
arrows point in the same direction. In addition, the movable part instance is translated to satisfy
the clearance specified. The effect of specifying the distance is illustrated in the following
figure:
If the face-to-face constraint conflicts with existing constraints, ABAQUS/CAE displays an error
message and cancels the operation. To avoid the conflict, you can try reversing the selection of the
part instance that will move and the part instance that will remain fixed. Alternatively, you can
convert the existing constraints to an absolute position and reapply the face-to-face constraint.
3-504
The Assembly module
parallel edge constraint does not specify the precise location of the part instances, and the distance
between the parallel faces is arbitrary. All position constraints are features of the assembly and can be
suppressed or deleted using the Feature Manipulation toolset.
Detailed instructions for constraining two part instances with parallel edges:
Tip: You can also apply the parallel edge constraint using the tool in the Assembly
module toolbox. For a diagram of the tools in the Assembly toolbox, see ``Using the Assembly
module toolbox,'' Section 16.6.
ABAQUS/CAE displays prompts in the prompt area to guide you through the procedure.
2. Select straight edges from the part instance that will move and the part instance that will remain
fixed, as shown in the following figure:
· Click OK to accept the direction of the arrow along the edge of the movable instance.
· Click Flip to reverse the direction of the arrow along the edge of the movable instance, and
click OK.
ABAQUS/CAE positions the movable part instance so that the two edges are parallel and the
arrows point in the same direction. The effect of changing the direction of the arrow is illustrated
in the following figure:
3-505
The Assembly module
If the parallel edge constraint conflicts with existing constraints, ABAQUS/CAE displays an error
message and cancels the operation. To avoid the conflict, you can try reversing the selection of the
part instance that will move and the part instance that will remain fixed. Alternatively, you can
convert the existing constraints to an absolute position and reapply the parallel edge constraint.
Tip: You can also apply the edge-to-edge constraint using the tool in the Assembly
module toolbox. For a diagram of the tools in the Assembly toolbox, see ``Using the Assembly
module toolbox,'' Section 16.6.
ABAQUS/CAE displays prompts in the prompt area to guide you through the procedure.
2. Select straight edges from the part instance that will move and the part instance that will remain
fixed, as shown in the following figure:
3-506
The Assembly module
· Click OK to accept the direction of the arrow along the edge of the movable instance.
· Click Flip to reverse the direction of the arrow along the edge of the movable instance and
click OK.
The effect of changing the direction of the arrow is illustrated in the next step.
If the part instances are three-dimensional, ABAQUS/CAE positions the movable part instance so
that the selected edges are parallel and coincident.
4. If the part instances are two-dimensional, you must specify the clearance between the selected
edges. In the text field that appears in the prompt area, enter the distance from the edge of the
movable part to the edge of the fixed part instance, positive along the normal to the edge of the
fixed instance.
ABAQUS/CAE positions the movable part instance so that the two edges are parallel and the
arrows point in the same direction. In addition, the movable part instance is translated to satisfy
the clearance specified. The effect of specifying the distance and changing the direction of the
arrow is illustrated with two-dimensional instances in the following figure:
If the edge-to-edge constraint conflicts with existing constraints, ABAQUS/CAE displays an error
message and cancels the operation. To avoid the conflict, you can try reversing the selection of the
part instance that will move and the part instance that will remain fixed. Alternatively, you can
convert the existing constraints to an absolute position and reapply the edge-to-edge constraint.
3-507
The Assembly module
Tip: You can also apply the coaxial constraint using the tool in the Assembly module
toolbox. For a diagram of the tools in the Assembly toolbox, see ``Using the Assembly module
toolbox,'' Section 16.6.
ABAQUS/CAE displays prompts in the prompt area to guide you through the procedure.
2. Select cylindrical or conical faces from the part instance that will move and the part instance that
will remain fixed, as shown in the following figure:
ABAQUS/CAE displays arrows along the axis of revolution of the selected faces.
· Click OK to accept the direction of the arrow along the axis of revolution of the face of the
movable instance.
· Click Flip to reverse the direction of the arrow along the axis of revolution of the face of the
movable instance, and click OK.
ABAQUS/CAE positions the movable part instance so that the two axes are coincident and the
3-508
The Assembly module
arrows point in the same direction. The effect of the coaxial constraint with the arrows selected as
shown above is illustrated in the following figure:
If the coaxial constraint conflicts with existing constraints, ABAQUS/CAE displays an error
message and cancels the operation. To avoid the conflict, you can try reversing the selection of the
part instance that will move and the part instance that will remain fixed. Alternatively, you can
convert the existing constraints to an absolute position and reapply the coaxial constraint.
3-509
The Assembly module
or curved edges, ABAQUS/CAE computes the contact position using this faceted representation.
Increasing the degree of curve refinement increases the accuracy of the contact positioning calculation;
however, the calculation will be significantly slower.
Even though you apply a contact constraint to two part instances, the physical proximity of the selected
surfaces is not enough to indicate any type of interaction between them. You must use the Interaction
module to specify coupling between surfaces.
To constrain two part instances by defining contact:
Tip: You can also define contact using the tool in the Assembly module toolbox. For a
diagram of the tools in the Assembly toolbox, see ``Using the Assembly module toolbox,''
Section 16.6.
ABAQUS/CAE displays prompts in the prompt area to guide you through the procedure.
2. Select the faces (for three-dimensional part instances) or edges (for two-dimensional part
instances) from the part instance that will move and the part instance that will remain fixed. You
can select more than one face or edge from both the fixed and the movable part instances.
Selecting multiple faces or edges is useful if you are not sure what part of the model will come in
contact when the movable part instance moves along the selected vector. However, for faster
processing you should select as few faces or edges as possible. You cannot select a datum plane.
3. Select the start and end points of the vector that defines the direction of motion. You can select
any existing vertices or datum points, or you can enter the coordinates in the text box in the
prompt area. If the part instances are axisymmetric, the translation vector must be parallel to the
axis of revolution.
The following figure illustrates how you define contact between edges of two-dimensional part
instances:
4. In the text box that appears in the prompt area, enter a value for the clearance between the two
selected faces; a negative value indicates over-closure.
ABAQUS/CAE moves the selected part instance along the vector until the two selected faces
3-510
The Assembly module
contact with the specified clearance. The following figure illustrates contact with zero clearance
and contact with a specified clearance.
For more information, see ``How the position constraint methods differ, '' Section 16.4.2.
If the contact constraint conflicts with existing constraints, ABAQUS/CAE displays an error
message and cancels the operation. To avoid the conflict, you can try reversing the selection of the
part instance that will move and the part instance that will remain fixed. Alternatively, you can
convert the existing constraints to an absolute position and reapply the contact constraint. If
possible, you should not mix a contact position constraint with other position constraints.
1. From the main menu bar, select Instance->Convert Constraints to convert any existing
constraints to the current position.
2. From the assembly, select the part instance whose constraints you want to convert. If the selection
is ambiguous, you can cycle through the candidate instances using the buttons in the prompt area.
You can also click the Instance List button on the right of the prompt area and select the instance
from the Feature List.
The part instance does not move, but ABAQUS/CAE converts any existing constraints to the
current position.
You cannot restore the original face, edge, coaxial, and contact constraints.
3-511
The Assembly module
· ``How conflicts can arise between position constraints, '' Section 16.4.3
Tip: You can also select the query tool in the toolbar.
2. From the Query dialog box, select one of the following and click Apply:
Instance Attributes
Instance Position
Select a part instance.
ABAQUS/CAE displays the following in the message area:
· Position of the origin of the instance relative to the global coordinate system
· The sum of the translations applied to the instance relative to the assembly's global
coordinate system
· The sum of the rotations applied to the instance relative to the assembly's global
coordinate system
3-512
The Assembly module
3-513
The Step module
4-514
The Step module
will be output during an analysis step, from which region of the model they will be output, and
at what rate they will be output. For example, you might request output of the entire model's
displacement field at the end of a step and also request the history of a reaction force at a
restrained point.
For additional information on steps, see ``Procedures: overview,'' Section 6.1.1 of the
ABAQUS/Standard User's Manual and the ABAQUS/Explicit User's Manual.
Analysis steps
4-515
The Step module
The initial step is followed by one or more analysis steps. Each analysis step is associated with
a specific analysis procedure. There is no limit to the number of analysis steps you can define,
but there are restrictions on the step sequence. (For more information, see ``Step sequence
restrictions,'' Section 17.3.3.)
You use items from the Step menu to create a step, to select and configure the analysis procedure used
during the step, and to manage existing steps. Alternatively, you can select Step->Manager from the
main menu bar to display the Step Manager.
For example, consider the following analysis of a section of a piping system:
Initial Step:
Apply boundary conditions to fix the left end of the pipe and to allow only axial movement at
the right end.
Step 1: Compress
Apply a compressive force to the right end of the pipe. This step is a general analysis step.
Step 2: Eigenmodes
Calculate the frequencies and modes of vibration of the pipe in its compressed state. This step
is a linear perturbation step.
Figure 17-1 shows the Step Manager after you create these steps.
The manager lists all of the steps in the analysis as well as a few salient details concerning each step.
Step 2, Eigenmodes, is indented to show that it is a linear perturbation step based on the state of the
model at the end of Step 1, Compress.
For detailed information on creating and editing steps, see the following sections:
4-516
The Step module
· Click the Basic tab in the Step Editor and toggle the Nlgeom setting.
For more information, see ``Accounting for geometric nonlinearity,'' Section 17.7.4, or see ``Linear and
nonlinear procedures,'' Section 6.1.2 of the ABAQUS/Standard User's Manual.
4-517
The Step module
· The procedures that you have already associated with existing steps.
For example, when you create the first step in an analysis, you can choose from a list of valid
procedure types; both ABAQUS/Standard and ABAQUS/Explicit procedure types appear in the list.
However, once you have created the first step, the list of valid procedure types in the Create Step
dialog box will change to include only those procedures that are compatible with the first step. For
example, if the first step is an ABAQUS/Standard step, ABAQUS/Explicit procedures no longer
appear in the list.
· ``What is the difference between field output and history output?, '' Section 17.4.2
· The region of the model and the integration points from which the values are written to the output
database.
· The rate at which the variable or component values are written to the output database.
ABAQUS/CAE selects a default set of output variables corresponding to the step's analysis procedure.
By default, output is requested from every node or integration point in the model and from default
section points. In addition, ABAQUS/CAE selects the default rate at which the variables are written to
the output database. The Output Database Request Manager allows you to view and modify the
default output requests as well as to create new output requests. To display the Output Database
Request Manager, select Output->Output Database
For example, Figure 17-2 shows the default state of the Output Database Request Manager after
4-518
The Step module
The Field output tabbed page contains the variables shown in Figure 17-2, and the History output
page is empty. (Field and history output are described in ``What is the difference between field output
and history output?,'' Section 17.4.2.) In addition, the entire model is selected as the region for output,
and the default section points are selected. Finally, each variable is output after every increment of the
step. (For more information on default output, see ``Output to the output database, '' Section 4.1.3 of the
ABAQUS/Standard User's Manual and the ABAQUS/Explicit User's Manual.)
If you click Edit in the Output Database Request Manager , an editor appears that allows you to
change either the field or the history output requests depending on which page is visible at the time.
When your analysis is complete, you use the Visualization module to read the output database and
graphically display the data that were written to it.
For detailed instructions on creating and editing output requests, see the following sections:
· ``Using the Output Database Request Manager to create and manage output requests, '' Section
17.9.1
4-519
The Step module
When you create an output request, you can choose either field output or history output.
Field output
Field output is output that you request from the entire model or from a large portion of the
model. Typically, field output is written to the output database at a low rate; for example, after
every step or at the end of the analysis. The Visualization module allows you to display field
output results in undeformed, deformed, contour, and symbol plots. (For more information, see
``Understanding plot modes and plot customization, '' Section 23.3.) ABAQUS/Standard
automatically writes every component of the variables that you include in the field output
request.
For example, if you were using solid elements to model a cantilever beam with a load at the
tip, you could request the stress (all six components) and the displacement (all six
components) data from the entire model after the last increment of the loading step. You could
then use the Visualization module to view a contour plot of stresses and deflections in the final
loaded state.
History output
History output is output that you request from a small portion of the model. Typically, history
output is written to the output database at a high rate; for example, after every increment. The
Visualization module allows you to display history output in X-Y plots. (For more information,
see ``Reading X-Y data from output database history output,'' Section 30.2.1.) When you
create a history output request, you can specify the individual components of the variables that
you want written to the output database.
For example, if you model the response of a cantilever beam with a load applied to the tip, you
might request the following output after each increment of the loading step:
You could then use the Visualization module to view an X-Y plot of stress at the root versus
displacement at the tip with increasing load.
4-520
The Step module
The field output editor is illustrated in Figure 17-3. The top part of the editor contains a list of the
variable categories that are applicable to the step procedure. You can click the check box next to a
category name to select all of the variables within that category, or you can click the arrow next to a
category name to display the list of variables in that category and then select individual variables.
In Figure 17-3 the user has selected the variable S, Stress components and invariants in the
Stresses category as well as all of the variables in the Strains and
Displacement/Velocity/Acceleration categories to be included in the output request for the step
named Beamload. ABAQUS will write output from the default section points after every five
increments.
Like the field output editor, the history output editor contains a list of variable categories that you can
expand to see the list of variables in each category. However, the history output editor also allows you
to specify individual components of a variable for which you want output. When requesting history
output, it is useful to specify individual components because these variables are typically output very
frequently--possibly as often as every increment.
For detailed instructions on selecting output variables and components, see the following sections:
4-521
The Step module
· You can specify the frequency in increments (for ABAQUS/Standard) or in intervals (for
ABAQUS/Explicit) at which ABAQUS writes data needed to the restart file. You can set the
frequency to zero to avoid writing the restart file during an ABAQUS/Standard step. However, it is
impossible to avoid writing the restart file for ABAQUS/Explicit steps; if you set the frequency to
zero for an ABAQUS/Explicit step, restart information will be written only at the end of the step.
· You can request that only one increment should be retained in the restart file, thus minimizing the
size of the file. When you select this option, data written to the restart file overlay data from the
previous increment. By default, ABAQUS does not overlay data.
For detailed instructions on requesting restart data, see ``Configuring restart output requests,'' Section
17.10.1.
4-522
The Step module
following files:
Using the Diagnostic Print dialog box is equivalent to including the *PRINT option in a solver input
file. You display the Diagnostic Print dialog box by selecting Output->Diagnostic Print from the
main menu bar.
For detailed instructions on requesting diagnostic printing, see ``Configuring diagnostic printing,''
Section 17.10.2.
· If you are working with a native geometric model, the set must contain only one vertex.
· If you are working with an orphan mesh, the set must contain only one node.
(For information about creating sets, see Chapter 45, "The Set and Surface toolsets.")
Once you have specified a set, you must indicate which degree of freedom you want to monitor at that
vertex or node and how often you want the information printed to the status and message files.
Requesting this information is analogous to including the following line in a solver input file:
4-523
The Step module
Note: Currently, these options are available only for Dynamic, Explicit steps.
4-524
The Step module
solution.
You can access the contact controls by selecting Other->Contact Controls from the main menu bar.
Customizing contact controls in the Step module is equivalent to including the *CONTACT
CONTROLS option in an ABAQUS/Explicit input file. For more information, see ``Common
difficulties associated with contact modeling,'' Section 20.5.1 of the ABAQUS/Explicit User's Manual.
Warning: Contact controls are intended for experienced analysts and should be used with great
care. The default settings of these controls are appropriate for most analyses. Changing these
values inappropriately may greatly increase the computational time of your analysis or produce
inaccurate results.
For detailed instructions for setting solution controls, see ``Customizing optional solution controls for
contact problems,'' Section 17.11.1.
The name of the step. Names of linear perturbation steps are indented relative to names of
general steps.
Procedure
The analysis procedure that you selected for this step when the step was created. You cannot
change the analysis procedure after you have created a step. The Procedure column also
indicates whether thermal and steady-state soils steps assume steady-state heat transfer or
transient heat transfer or if neither is applicable.
Nlgeom
Whether the analysis step accounts for geometric nonlinearities. You use the Nlgeom button
to control the Nlgeom setting for a particular step. Once you have set the Nlgeom option for a
4-525
The Step module
The time period for the step. The default value for the time period is 1.0 time unit. Click Edit
to display the step editor so that you can modify the time period.
You use the buttons across the bottom of the Step Manager dialog box to create a step that follows the
selected step or to manipulate the selected step. You use the Dismiss button to close the Step
Manager dialog box. You can perform the same tasks using the pull-down menus available from the
Step menu, located in the main menu bar.
Warning: If you use the Step Manager or the Step menu to delete a step, objects associated with
that step, such as prescribed conditions or output requests, are also deleted.
· Click Create in the Step Manager. (You can display the Step Manager by selecting
Step->Manager from the main menu bar.)
2. If desired, use the Name text field to change the name of the new step.
All steps must have unique names, and you cannot name a step ``Initial''.
4-526
The Step module
3. From the list of existing steps, select the step after which the new step will be inserted.
4. Click the Procedure type menu button and select either General or Linear perturbation from the
list that appears.
The lower half of the dialog box displays a list of available procedures.
6. Use the Edit Step dialog box to modify the settings from their default values and to provide values
for optional settings. (For detailed help on a particular editor feature, select Help->On Context
from the main menu bar and then click the feature of interest.)
7. Click OK.
ABAQUS/CAE closes the Edit Step dialog box, and the new step appears in the Step Manager.
· ``Linear and nonlinear procedures,'' Section 6.1.2 of the ABAQUS/Standard User's Manual
2. Use the tabs within the step editor to modify the settings. (For detailed help on a particular editor
feature, select Help->On Context from the main menu bar and then click the feature of interest.)
3. Click OK to close the step editor and save the new settings.
4-527
The Step module
Detailed instructions for changing the Nlgeom setting for an existing step:
1. To display the Nlgeom dialog box and to change the setting where applicable, do one of the
following:
2. From the Nlgeom dialog box, click the step name of interest to turn Nlgeom on or off for that
step.
If Nlgeom is turned on for a step, a checkmark appears in the Nlgeom column. If Nlgeom is
turned off for a step, no tickmark appears.
4-528
The Step module
Time incrementation
· When you choose Automatic time incrementation, ABAQUS starts the incrementation using
the value entered for the initial increment size. The size of subsequent time increments are
adjusted based on how quickly the solution converges. This option is the default selection.
· When you choose Fixed time incrementation, ABAQUS uses the value entered for the initial
increment size throughout the step.
4-529
The Step module
Warning: Choosing Fixed time incrementation may prevent the solution from converging
and is not recommended.
ABAQUS checks for the maximum increment size only when you analyze your model using
automatic time incrementation. ABAQUS will not increase the increment size beyond this
value during the analysis. If you do not specify this value, ABAQUS/CAE sets the value to
that of the total time period.
Note: A value must be entered for each of the incrementation options described above.
ABAQUS/CAE does not allow you to create the step if you delete the default value for an
incrementation option but fail to provide another.
For detailed information on other items in the Incrementation tabbed page, click Help->On Context
and then click the item of interest.
4-530
The Step module
· ``Using the Output Database Request Manager to create and manage output requests, '' Section
17.9.1
· The variables that ABAQUS writes to the output database during the step.
· The frequency at which ABAQUS writes the variables to the output database.
· Where applicable, the section points for which ABAQUS writes data.
To configure an output request, select the desired step from the list of steps on the left side of the
Output Database Request Manager . The Field output and History output tabbed pages display the
output requests defined during that step. You can use the buttons along the bottom of the Output
Database Request Manager to edit and manipulate these output requests or to create new output
requests.
Note: You must use the Output Database Request Manager to manage your output requests;
there are no equivalent menu selections.
4-531
The Step module
the default field output request, or you can create additional field or history output requests.
Detailed instructions for creating an output request:
1. From the list of steps on the left side of the Output Database Request Manager , select the
analysis step during which ABAQUS will write the desired data to the output database.
4. In the editor, enter the data necessary to define the output request. For more information on using
the editor, see ``Creating and modifying field output requests,'' Section 17.9.3, or ``Using the
history output editor,'' Section 17.9.4.
5. When you have finished configuring your output request, click OK to save your selection and
return to the Output Database Request Manager .
The Output Database Request Manager displays the new output request.
1. In the top part of the field output editor, use the following techniques to specify the variables of
interest:
· In the top half of the editor, click the arrow next to the desired variable category. From the list
of variables that appears, select the variables of your choice.
· Toggle the desired variable category. This action selects or deselects all variables within that
category.
The check box next to a variable category becomes completely filled when all variables within that
category are selected. The box becomes half filled if only some of the variables within that
category are selected.
4-532
The Step module
Note: If you prefer, you can change the Variables option setting from Select from above to Edit and then manually type or
delete variables in the Edit text field.
2. Choose one of the following to modify the section points from which variables will be output
during the selected step:
Defaults
Choose Defaults to request that ABAQUS write data to the output database from the
default section points. ABAQUS chooses the default section points based on the section
selected in the Property module. (The default section points are usually the outer fibers of
the section.) For more information see Chapter 15, "The Property module."
List
Choose List to manually type the section points for which ABAQUS will write data to the
output database. The specified section points are used only during the selected output
request; ABAQUS reverts to the default section points for subsequent output requests.
3. Specify the desired output frequency. For more information, see ``Controlling the output
frequency'' in ``Output to the output database, '' Section 4.1.3 of the ABAQUS/Standard User's
Manual and the ABAQUS/Explicit User's Manual.
4. Choose one of the following to modify the region from which variables will be output during the
selected step:
Whole model
Choose Whole model to request that ABAQUS write data to the output database for the
entire model.
Set name
Choose Set name to request that ABAQUS write data to the output database for only the
named region.
5. When you have finished modifying the output request, click OK to save your changes and return to
the Output Database Request Manager .
4-533
The Step module
1. In the top part of the history output editor, use the following techniques to specify the variables
and variable components of interest:
· In the top half of the editor, click the arrow next to the desired variable category. From the list
of variables that appears, select the variables of your choice. If a variable of interest has
components, click the arrow next to the variable and select the components of interest. To
select or deselect all components of a variable, toggle the variable itself.
· Toggle the desired variable category to select or deselect all variables and variable
components within that category.
The check box next to a variable category name becomes completely filled when all variables
within that category are selected as well as all of the components of those variables. The box
becomes half filled if only some of the variables or variable components within that category are
selected. Likewise, the check box next to a variable name becomes completely filled when all
components of that variable are selected. The box becomes half filled if only some of the
components of that variable are selected.
Note: If you prefer, you can change the Variables option setting from Select from above to Edit and then manually type or
delete variable components in the Edit text field.
2. Choose one of the following to modify the section points from which variables or components will
be output during the selected step:
Defaults
Choose Defaults to request that ABAQUS write data to the output database from the
default section points. ABAQUS/CAE chooses the default section points based on the
section selected or defined in the Property module. (The default section points are usually
the outer fibers of the section.) For more information see Chapter 15, "The Property
module."
List
Choose List to manually type or delete the section points for which ABAQUS will write
data to the output database. The specified section points are used only during the selected
output request; ABAQUS reverts to the default section points for subsequent output
requests.
3. Specify the desired output frequency. For more information, see ``Controlling the output
frequency'' in ``Output to the output database, '' Section 4.1.3 of the ABAQUS/Standard User's
Manual and the ABAQUS/Explicit User's Manual.
4-534
The Step module
4. Choose one of the following to modify the region from which variables will be output during the
selected step:
Whole model
Choose Whole model to request that ABAQUS write data to the output database for the
entire model.
Set name
Choose Set name to request that ABAQUS write data to the output database for only the
named region.
5. When you have finished modifying the output request, click OK to save your changes and return to
the Output Database Request Manager .
1. From the list of steps on the left of the Output Database Request Manager , select the analysis
step containing the output request to delete.
2. Click the tab (Field output or History output) for the output request to delete.
3. Select the output request to delete. You cannot select more than one output request at a time.
4-535
The Step module
ABAQUS/CAE asks for confirmation before overwriting the existing output requests.
Detailed instructions for selecting default output requests:
1. From the list of steps on the left of the Output Database Request Manager , select the analysis
step for which all of the field or history output requests will be set to their default value.
2. Click either the Field output tab or the History output tab.
4. Click Yes to restore the system-defined output requests for the selected type of output.
ABAQUS/CAE deletes all the output requests on the tabbed page and restores the default output
requests (if any).
4-536
The Step module
· ``Output to the output database, '' Section 4.1.3 of the ABAQUS/Standard User's Manual and the
ABAQUS/Explicit User's Manual
2. In the Frequency column for the desired step, specify the frequency in increments (for
ABAQUS/Standard) or in intervals (for ABAQUS/Explicit) at which ABAQUS writes model
definition data and output requests to the restart file.
By default, ABAQUS writes restart information after every increment. To avoid writing the restart
file during an ABAQUS/Standard step, set the frequency to zero. (It is impossible to avoid writing
the restart file for ABAQUS/Explicit steps; if you set the frequency to zero for an
ABAQUS/Explicit step, restart information will be written only at the end of the step.)
3. Click the Overlay column to request that only one increment be retained in the restart file, thus
minimizing the size of the file.
You can use the Overlay column only when the value in the Frequency column is greater than
zero.
5. When you have finished configuring your restart output requests, click OK to close the Restart
Requests dialog box.
4-537
The Step module
2. In the Frequency column, specify the frequency at which you want diagnostic printing data
written for each step. (This option is not available for ABAQUS/Explicit analyses.)
3. Click in the other columns to request specific diagnostic information during a particular step.
A check mark appears indicating that type of diagnostic printing has been enabled during the step.
Click in the column again to turn off diagnostic printing.
4. When you have finished configuring your diagnostic printing, click OK to exit the Diagnostic
Print dialog box.
2. In the dialog box, toggle Monitor a degree of freedom throughout the analysis.
If Monitor a degree of freedom throughout the analysis is toggled on, the monitoring options
4-538
The Step module
3. Click the arrow next to the Point region field and select the set of your choice from the list that
appears. (ABAQUS/CAE displays an error message if you select a set containing more than one
vertex or node.)
4. In the Degree of freedom field, enter the degree of freedom that you want to monitor.
5. If you are performing an ABAQUS/Standard analysis, in the Print to the message file every n
increments field, enter how often you want ABAQUS to write the degree of freedom values to the
message file.
(There is no option to control the frequency at which values are written to the status file, since this
frequency is determined by ABAQUS. For more information, see ``Output,'' Section 4.1.1 of the
ABAQUS/Standard User's Manual and the ABAQUS/Explicit User's Manual.)
· ``Customizing optional solution controls for contact problems, '' Section 17.11.1
4-539
The Step module
2. In the Contact Controls Manager, select the step of interest and then click Edit.
ABAQUS/CAE displays the contact controls editor.
2. In the Adaptive Mesh Domain Manager, select the step during which you will configure the
adaptive meshing and click Edit.
ABAQUS/CAE displays the adaptive mesh domain editor.
3. At the top of the editor, select Use the adaptive mesh domain below .
a. Select the set corresponding to the region you want to remesh. (For information on
4-540
The Step module
creating sets, see Chapter 45, "The Set and Surface toolsets.")
b. If you want to specify nondefault adaptive mesh controls, toggle on Adaptive mesh
controls and then select the name of the adaptive mesh controls to associate with the
region.
If you have not yet created mesh controls, you can click Create to the right of the
Adaptive mesh controls field to define the controls that you want to assign to the
adaptive mesh domain.
c. Type the Frequency, in increments, at which ABAQUS/CAE will remesh the region.
d. Type the number of Initial remeshing sweeps that ABAQUS/CAE will apply at the
beginning of the step.
e. Type the number of Remeshing sweeps per increment . An increment in this case is
each adaptive mesh increment, as defined by the Frequency setting above.
5. Click OK to save the settings and to close the adaptive mesh domain editor.
The Adaptive Mesh Domain Manager displays the adaptive mesh controls associated with the
step.
2. In the dialog box that appears, type a name for the adaptive mesh controls and click Continue.
ABAQUS/CAE displays the adaptive mesh controls editor.
3. In the editor, select the desired mesh controls. (For more information, see ``Adaptive meshing and
4-541
The Step module
4. Click OK to save the named set of controls and close the editor.
4-542
The Interaction module
· Mechanical and thermal interactions between regions of a model or between a region of a model
and its surroundings.
The tutorial will help you become familiar with techniques for creating and applying interaction
definitions.
· Elastic foundations.
Interactions are step-dependent objects, which means that when you define them, you must indicate in
which steps of the analysis they are active. (For more information about step-dependent objects, see
``Understanding the status of an object in a step, '' Section 6.5.3.) For example, you can define film and
radiation conditions on a surface only during a heat transfer, coupled temperature-displacement, or
coupled thermal-electrical step. Similarly, you can define interaction with a user-defined
actuator/sensor only during the initial step.
The Set and Surface toolsets in the Interaction module allow you to define and name regions of your
5-543
The Interaction module
model to which you would like interactions applied. You can use the Amplitude toolset to define
variations in some interaction attributes over the course of the analysis.
ABAQUS/CAE does not recognize mechanical contact between part instances or regions of an
assembly unless that contact is specified in the Interaction module; the mere physical proximity of two
surfaces in an assembly is not enough to indicate any type of interaction between the surfaces.
· ``Contact and interaction analysis: overview, '' Section 21.1.1 of the ABAQUS/Standard User's
Manual and ``Contact analysis: overview,'' Section 20.1.1 of the ABAQUS/Explicit User's Manual
5-544
The Interaction module
ABAQUS/Standard input file. For more information, see ``Element foundations,'' Section
2.2.2 of the ABAQUS/Standard User's Manual.
Actuator/sensor
An actuator/sensor interaction models a combination of sensors and actuators and, therefore,
allows for modeling control system components. Currently, this type of interaction allows
sensing and actuation at just one point.
The interaction definition and its optionally associated property are used to define the basic
aspects of the interaction, but the user must provide user subroutine UEL to supply the specific
formulae for how actuation depends on sensor readings. You specify the name of the file
containing the user subroutine when you create the analysis job in the Job module.
Warning: This feature is intended for advanced users only. Its use in all but the simplest
test examples will require considerable coding by the user/developer. ``User-defined
elements,'' Section 18.8.1 of the ABAQUS/Standard User's Manual, should be read before
proceeding.
Actuator/sensor interactions are available only for ABAQUS/Standard analyses. For more
information, see ``UEL,'' Section 23.2.19 of the ABAQUS/Standard User's Manual, and Part
VIII, "User Subroutines and Utilities," of the ABAQUS/Standard User's Manual.
· ``Contact and interaction analysis: overview, '' Section 21.1.1 of the ABAQUS/Standard User's
Manual and ``Contact analysis: overview,'' Section 20.1.1 of the ABAQUS/Explicit User's Manual
5-545
The Interaction module
Contact
A contact interaction property can define tangential behavior (friction and elastic slip) and
normal behavior (hard, soft, or damped contact and separation). In addition, a contact property
can contain information about damping, thermal conductance, thermal radiation, and heat
generation due to friction. A contact interaction property can be referred to by a
surface-to-surface or self-contact interaction.
Film condition
A film condition interaction property defines a film coefficient as a function of temperature
and field variables. A film condition interaction property can be referred to only by a film
condition interaction.
Actuator/sensor
An actuator/sensor interaction property provides the PROPS, JPROPS, NPROPS, and
NJPROPS variables that are passed into a user subroutine UEL used with an actuator/sensor
interaction.
Tie
Tie constraints allow you to fuse together two regions even though the meshes created on the
surfaces of the regions may be dissimilar. Once you activate a tie constraint, you cannot
deactivate it in any later analysis steps.
Creating a tie constraint is analogous to including the *CONTACT PAIR, TIED option in a
solver input file. For more information, see ``Defining tied contact,'' Section 21.2.4 of the
ABAQUS/Standard User's Manual and Section 20.2.4 of the ABAQUS/Explicit User's
Manual.
Equation
Equations are linear, multi-point equation constraints that allow you to describe linear
constraints between individual degrees of freedom. Defining an equation constraint is
analogous to including the *EQUATION option in a solver input file. For more information,
see ``Linear constraint equations,'' Section 20.2.1 of the ABAQUS/Standard User's Manual
5-546
The Interaction module
· The Interaction Property Manager allows you to create and manage interaction properties.
For example, a list of interaction properties appears in the Interaction Property Manager shown in
Figure 18-1.
The Create, Edit, Copy, and Delete buttons in the managers allow you to create new objects or to
edit, copy, and delete existing ones. You can also initiate these procedures using the Interaction,
Property, and Constraint menus in the main menu bar. After you select a management operation from
the main menu bar, the procedure is exactly the same as if you had clicked the corresponding button
inside the manager dialog box.
5-547
The Interaction module
The decision whether to use the menu or the manager dialog box is yours. In general, the menu is more
convenient if you are performing isolated operations; the advantages of the manager dialog box
become apparent when you are performing several operations in sequence, or when you need to
browse through a long list of existing objects.
In addition to creating, editing, copying, and deleting interactions the Interaction Manager and
Interaction menu allow you to rename an interaction. You cannot rename a property.
The Interaction Manager is a step-dependent manager, which means that it contains additional
information on the history of each interaction through the analysis. This manager also contains buttons
that allow you to manipulate the stepwise history of interactions. (For more information, see ``What
are step-dependent managers?,'' Section 6.5.2.) The Interaction Manager is shown in Figure 18-2.
For detailed instructions on creating interactions, interaction properties, and constraints, see ``Creating
interactions,'' Section 18.8.1, and ``Defining equation constraints,'' Section 18.8.11.
5-548
The Interaction module
Each interaction editor displays the current step and the name and type of the object that you are
defining in the top panel of the dialog box. The format of the rest of the editor varies depending on the
type of object you are defining. For example, the surface-to-surface contact editor for
ABAQUS/Standard analyses is shown in Figure 18-3.
Interaction editors sometimes contain one or more Options buttons at the bottom of the dialog box. If
you click one of these buttons, another dialog box appears that allows you to specify data concerning
some aspect of the interaction. For example, the Interference Fit button in the editor shown in Figure
18-3 displays a dialog box that allows you to set interference fit options. If you do not change any
settings in an options dialog box, the default settings are applied automatically to the interaction.
Once you have created an interaction, you can modify the interaction in the following ways:
· You can modify some or all of the data that you entered in the editor when you created the
interaction.
· You can use the Interaction Manager to modify the stepwise history of the interaction. (For more
information, see ``What are step-dependent managers?,'' Section 6.5.2.)
You can display information on a particular editor feature by selecting Help->On Context from the
main menu bar and then clicking the editor feature of interest.
5-549
The Interaction module
The format of the contact property editor, on the other hand, is identical to the material editor in the
Property module (see ``Creating materials,'' Section 15.6.1, for more information). Like the material
editor, the contact property editor contains menus from which you select options to include in the
property definition, as shown in Figure 18-5.
Figure 18-5 The contact property editor contains Mechanical and Thermal option menus.
5-550
The Interaction module
When you select an option from a menu, the name of the option appears in the Contact Property
Options list at the top of the editor, and the option becomes part of your interaction property
definition. In addition, the option definition area in the lower half of the editor changes to provide
fields in which you can specify information for the currently selected option.
For example, the Contact Property Options list in Figure 18-6
Figure 18-6 A mechanical contact property definition that includes the Tangential Behavior and
Normal Behavior options.
reflects that the Tangential Behavior and Normal Behavior options (located in the Mechanical
menu) have been included in the property definition. Tangential Behavior is currently selected, and
the related parameters appear in the lower half of the editor. If you want to remove an option from a
contact property definition, you can select that option from the Contact Property Options list and
then click Delete.
You can display help on a particular feature of the editor by selecting Help->On Context from the
main menu bar and then clicking the feature of interest. For detailed instructions for creating
properties, see the following sections:
5-551
The Interaction module
You can display information on a particular editor feature by selecting Help->On Context from the
main menu bar and then clicking the editor feature of interest.
For detailed instructions on creating constraints, see ``Defining equation constraints,'' Section 18.8.11,
and ``Defining tie constraints,'' Section 18.8.10.
5-552
The Interaction module
This section contains a short tutorial that will help you to become more familiar with the Interaction
module. The tasks in this tutorial involve the clamp model shown in Figure 18-8.
You will create an interaction that defines the contact between the inner surfaces of the clamp. Such an
interaction would be necessary for an analysis in which a load is applied to each side of the clamp,
causing the prongs to come into contact.
Although you can create interaction properties in the middle of the procedure for creating interactions,
this tutorial will show you how to create the interaction property first and then create an interaction
that refers to that property.
After you have created the interaction, you will modify its history so that it is active in Step 2 and
inactive thereafter.
3. Click the File type arrow, and select Model Database (*.cae) if it is not already selected.
4. In the Selection field at the bottom of the Open Database dialog box, delete the default text and
type the path of the file containing the model database.
5-553
The Interaction module
5. Click OK.
ABAQUS/CAE reads the model database containing the clamp model.
· Use a combination of the view manipulation tools and the display option tools in the
toolbar and the tools in the Views toolbox to resize and reposition the model as necessary.
(The Views toolbox appears when you select from the toolbar.)
In particular, you will probably find the magnification tool and the rotation tool
useful for displaying the model at a convenient size and orientation.
· When necessary, click the Iso tool in the Views toolbox to return the model to its
original size and position in the viewport.
For more information on the view manipulation tools, see Chapter 8, "Manipulating the view
and controlling perspective."
c. Click Continue.
The contact property editor appears.
4. From the editor menu bar, select Mechanical->Tangential Behavior. In the lower half of the
editor, specify information relating to the Tangential Behavior option:
5-554
The Interaction module
a. Click the Friction formulation menu button to see the available formulations. Select the
Penalty formulation.
5. From the editor menu bar, select Mechanical->Normal Behavior. In the lower half of the editor,
review the settings for the Normal Behavior option:
a. Click the Pressure-Overclosure menu button to see the options for defining the
pressure-clearance relationship between the surfaces. Accept "Hard" Contact.
d. Click Continue.
3. Select the inside lower surface of the clamp to be the master surface, as shown in Figure 18-9.
5-555
The Interaction module
5. From the buttons in the prompt area, select Surface as the slave type.
6. Select the inside upper surface of the clamp to be the slave surface, as shown in Figure 18-10.
By default, when you click in a region that overlaps more than one face, ABAQUS/CAE selects
the face that is "closest" to the screen. To select the inside upper surface of the clamp, you need to
turn off the default behavior and cycle through the valid selections.
5-556
The Interaction module
b. In the dialog box, identify the Select the Entity Closest to the Screen tool by holding
the cursor briefly over each button in the dialog box; toggle off this tool.
8. In the editor, notice that the master and slave surfaces are labeled as (Picked) to indicate that you
picked them directly from the viewport. The Switch button allows you to interchange your master
and slave surface selections without having to start over.
10. Accept Friction as the interaction property. (If more properties were defined, you could click
the arrow next to the Interaction property field to see the list of available properties and then
select the property of your choice.)
11. Click Interference Fit to see the contents of the Interference Fit Options dialog box. You can
accept the default selections and values provided for the interaction.
12. Click OK to save the interaction definition and to exit the editor.
5-557
The Interaction module
2. In the dialog box, enter the name Top_Left for the first set, and click Continue.
3. Select the upper left corner point on the top clamp piece as the geometry for the set, and click
mouse button 2 in the viewport to accept the selected geometry.
4. Use the same method to create a geometry set called Bottom_Right that contains the lower
right corner point of the bottom clamp piece.
2. In the dialog box, enter the name asymmetry for the constraint.
See ``Entering tabular data,'' Section 6.3.5, for more information on entering information in the
table editor.
5-558
The Interaction module
In this section you will use the buttons in the Interaction Manager to activate the interaction in
Step-2 of the analysis rather than in Step-1, and you will deactivate the interaction in Step-3. In other
words, you will specify that contact be recognized between the surfaces in Step-2 of the analysis but
become undefined in Step-3.
To alter the history of the interaction:
2. Expand the width of the Interaction Manager by dragging either the left or the right edge until all
of the analysis steps are visible in the manager table.
3. In the Interaction Manager, click the cell labeled Created in the column labeled Step-1.
That cell becomes highlighted.
5. In the manager, click in the cell labeled Propagated in the column labeled Step-3.
5-559
The Interaction module
6. Click Deactivate.
The Propagated status in Step-3 changes to Inactive.
· Contact interaction definitions refer to interaction properties, which contain information about
friction and other behavior between surfaces.
· You can use the Interaction Manager to view and, in some cases, to manipulate the stepwise
history of an interaction.
5-560
The Interaction module
· ``Editing the region to which an interaction or constraint is applied, '' Section 18.8.13
See also ``What are step-dependent managers?,'' Section 6.5.2, for information on managing
interactions.
The available categories and types of interactions depend on the procedure selected for the step. For
example, you can define heat flux on a surface only during a heat transfer, coupled
temperature-displacement, or coupled thermal-electrical step. Similarly, you can define interactions
with a user-defined actuator/sensor only during the initial step.
Detailed instructions for creating interactions:
Tip: You can also create an interaction using the tool in the Interaction module
toolbox.
· Name the interaction. For more information about naming objects, see ``Using basic dialog
box components,'' Section 6.3.1.
3. Click Continue to create the interaction and to close the Create Interaction dialog box.
5-561
The Interaction module
4. Select the region to which to apply the interaction. For more information, see Chapter 9, "Selecting
objects within the viewport.
5. In the editor that appears or, if applicable, in the prompt area, enter any data necessary to define
the interaction.
For detailed instructions on creating different types of interactions, see the following sections:
Tip: You can also create a property using the tool in the Interaction module toolbox.
2. Enter a property name of your choice. For more information about naming objects, see ``Using
basic dialog box components,'' Section 6.3.1.
5-562
The Interaction module
4. In the editor, enter all of the data necessary to define the interaction property.
Note: You can display help on a particular editor feature by selecting Help->On Context from the main menu bar and then
clicking the editor feature of interest.
· Equation constraints that describe linear constraints between individual degrees of freedom.
· Tie constraints that tie two separate surfaces together so that there is no relative motion between
them.
Tip: You can also create a constraint using the tool in the Interaction module toolbox.
a. Name the constraint. For more information about naming objects, see ``Using basic dialog
box components,'' Section 6.3.1.
3. Click Continue to create the constraint and to close the Create Constraint dialog box.
4. If applicable, select the region to which to apply the constraint. For more information, see Chapter
9, "Selecting objects within the viewport."
5-563
The Interaction module
5. In the editor that appears, enter any data necessary to define the constraint.
For detailed instructions on creating different types of interactions, see the following sections:
5-564
The Interaction module
Tip: You can also create an interaction using the tool in the Interaction module
toolbox.
· Name the interaction. For more information about naming objects, see ``Using basic dialog
box components,'' Section 6.3.1.
· Use the mouse to select a region in the viewport. (For more information, see ``Selecting
objects within the current viewport, '' Section 9.2.) Click mouse button 2 to indicate you have
finished selecting. You must select a region from only one part instance; the region that you
select cannot span multiple part instances.
Tip: You can limit the types of objects that you can select in the viewport by clicking the
selection filter tool in the prompt area and then clicking the selection filter of your
choice in the dialog box that appears. See ``Using the selection options,'' Section 9.3, for
more information.
If the model contains a combination of orphan mesh instances and native geometric part
instances, click one of the following from the prompt area:
- Click Geometry if you want to select the surface or vertex from a native geometric part
instance.
- Click Mesh if you want to select the surface or node from an orphan mesh instance.
5-565
The Interaction module
If you are selecting a surface from an orphan mesh, you have the option of either selecting
individual element faces or specifying a face angle. See ``Using the face angle method to
create a surface from an orphan mesh,'' Section 9.2.3, for more information.
· Use an existing surface to define the region. On the right side of the prompt area, click
Surfaces. Select an existing surface from the Region Selection dialog box that appears, and
click Continue.
Note: The default selection method is based on the selection method you most recently employed. To revert to the other
method, click Select in Viewport or Surfaces on the right side of the prompt area.
· Select Node Region if you want to select a region from which to create a contact node set.
Use one of the same methods described earlier to select the slave surface or region. As with the
master surface, the surface or region that you select cannot span multiple part instances.
6. After you select the slave surface, the Edit Interaction dialog box appears. The Switch button
allows you to interchange your master and slave surface selections without having to start over.
In the Edit Interaction dialog box, do the following:
· Choose the sliding formulation. For more information, see ``Relative surface motions,''
Section 21.3.2 of the ABAQUS/Standard User's Manual and Section 20.3.4 of the
ABAQUS/Explicit User's Manual.
· If you will be performing an ABAQUS/Standard analysis, specify the slave node adjustment
option of your choice. For more information, see ``Adjusting initial surface positions and
specifying initial clearances in contact pairs,'' Section 21.2.2 of the ABAQUS/Standard User's
Manual.
· Select an interaction property. If desired, click Create to create the interaction property.
· Enter the interference fit options, if desired. For more information, see ``Adjusting initial
surface positions and specifying initial clearances in contact pairs, '' Section 21.2.2 of the
ABAQUS/Standard User's Manual and Section 20.2.2 of the ABAQUS/Explicit User's
Manual.
Note: You can display help on a particular editor feature by selecting Help->On Context from the main menu bar and then
clicking the editor feature of interest.
5-566
The Interaction module
Tip: You can also create an interaction using the tool in the Interaction module
toolbox.
· Name the interaction. For more information about naming objects, see ``Using basic dialog
box components,'' Section 6.3.1.
· Use the mouse to select a region in the viewport. (For more information, see ``Selecting
objects within the current viewport, '' Section 9.2.) You must select a region from only one part
instance; the region that you select cannot span multiple part instances.
Tip: You can limit the types of objects that you can select in the viewport by clicking the
selection filter tool in the prompt area and then clicking the selection filter of your
choice in the dialog box that appears. See ``Using the selection options,'' Section 9.3, for
5-567
The Interaction module
more information.
If the model contains a combination of orphan mesh instances and native geometric part
instances, click one of the following from the prompt area:
- Click Geometry if you want to select the surface or vertex from a native geometric part
instance.
- Click Mesh if you want to select the surface or node from an orphan mesh instance.
If you are selecting a surface from an orphan mesh, you have the option of either selecting
individual element faces or specifying a face angle. See ``Using the face angle method to
create a surface from an orphan mesh,'' Section 9.2.3, for more information.
· Use an existing surface to define the region. On the right side of the prompt area, click
Surfaces. Select an existing surface from the Region Selection dialog box that appears, and
click Continue.
Note: The default selection method is based on the selection method you most recently employed. To revert to the other
method, click Select in Viewport or Surfaces on the right side of the prompt area.
5. In the Edit Interaction dialog box that appears, choose the interaction property.
6. From the Edit Interaction dialog box, click OK to create the interaction.
5-568
The Interaction module
Tip: You can also create an interaction using the tool in the Interaction module
toolbox.
· Name the interaction. For more information about naming objects, see ``Using basic dialog
box components,'' Section 6.3.1.
· Use the mouse to select a region in the viewport. (For more information, see ``Selecting
objects within the current viewport, '' Section 9.2.) You must select a region from only one part
instance; the region that you select cannot span multiple part instances.
Tip: You can limit the types of objects that you can select in the viewport by clicking the
selection filter tool in the prompt area and then clicking the selection filter of your
choice in the dialog box that appears. See ``Using the selection options,'' Section 9.3, for
more information.
If the model contains a combination of orphan mesh instances and native geometric part
instances, click one of the following from the prompt area:
- Click Geometry if you want to select the surface or vertex from a native geometric part
instance.
- Click Mesh if you want to select the surface or node from an orphan mesh instance.
If you are selecting a surface from an orphan mesh, you have the option of either selecting
individual element faces or specifying a face angle. See ``Using the face angle method to
create a surface from an orphan mesh,'' Section 9.2.3, for more information.
· Use an existing surface to define the region. On the right side of the prompt area, click
Surfaces. Select an existing surface from the Region Selection dialog box that appears, and
click Continue.
Note: The default selection method is based on the selection method you most recently employed. To revert to the other
method, click Select in Viewport or Surfaces on the right side of the prompt area.
5. In the text field that appears in the prompt area, enter the foundation stiffness per area.
ABAQUS/CAE creates the elastic foundation interaction.
5-569
The Interaction module
Tip: You can also create an interaction using the tool in the Interaction module
toolbox.
· Name the interaction. For more information about naming objects, see ``Using basic dialog
box components,'' Section 6.3.1.
· Select the step. You can define heat flux from a surface only during a heat transfer, coupled
temperature-displacement, or coupled thermal-electrical step.
· Use the mouse to select a region in the viewport. (For more information, see ``Selecting
objects within the current viewport, '' Section 9.2.) You must select a region from only one part
instance; the region that you select cannot span multiple part instances.
Tip: You can limit the types of objects that you can select in the viewport by clicking the
selection filter tool in the prompt area and then clicking the selection filter of your
choice in the dialog box that appears. See ``Using the selection options,'' Section 9.3, for
more information.
5-570
The Interaction module
If the model contains a combination of orphan mesh instances and native geometric part
instances, click one of the following from the prompt area:
- Click Geometry if you want to select the surface or vertex from a native geometric part
instance.
- Click Mesh if you want to select the surface or node from an orphan mesh instance.
If you are selecting a surface from an orphan mesh, you have the option of either selecting
individual element faces or specifying a face angle. See ``Using the face angle method to
create a surface from an orphan mesh,'' Section 9.2.3, for more information.
· Use an existing surface to define the region. On the right side of the prompt area, click
Surfaces. Select an existing surface from the Region Selection dialog box that appears, and
click Continue.
Note: The default selection method is based on the selection method you most recently employed. To revert to the other
method, click Select in Viewport or Surfaces on the right side of the prompt area.
5. In the Edit Interaction dialog box that appears, enter the required data. You must use the
Amplitude toolset to create the desired film coefficient and sink amplitudes.
Note: You can display help on a particular editor feature by selecting Help->On Context from the main menu bar and then
clicking the editor feature of interest.
6. From the Edit Interaction dialog box, click OK to create the interaction.
5-571
The Interaction module
Tip: You can also create an interaction using the tool in the Interaction module
toolbox.
· Name the interaction. For more information about naming objects, see ``Using basic dialog
box components,'' Section 6.3.1.
· Select the step. You can define heat flux from a surface only during a heat transfer, coupled
temperature-displacement, or coupled thermal-electrical step.
· Use the mouse to select a region in the viewport. (For more information, see ``Selecting
objects within the current viewport, '' Section 9.2.) You must select a region from only one part
instance; the region that you select cannot span multiple part instances.
Tip: You can limit the types of objects that you can select in the viewport by clicking the
selection filter tool in the prompt area and then clicking the selection filter of your
choice in the dialog box that appears. See ``Using the selection options,'' Section 9.3, for
more information.
If the model contains a combination of orphan mesh instances and native geometric part
instances, click one of the following from the prompt area:
- Click Geometry if you want to select the surface or vertex from a native geometric part
instance.
- Click Mesh if you want to select the surface or node from an orphan mesh instance.
If you are selecting a surface from an orphan mesh, you have the option of either selecting
individual element faces or specifying a face angle. See ``Using the face angle method to
create a surface from an orphan mesh,'' Section 9.2.3, for more information.
· Use an existing surface to define the region. On the right side of the prompt area, click
Surfaces. Select an existing surface from the Region Selection dialog box that appears, and
click Continue.
Note: The default selection method is based on the selection method you most recently employed. To revert to the other
method, click Select in Viewport or Surfaces on the right side of the prompt area.
5. In the Edit Interaction dialog box that appears, enter the required data. You must use the
5-572
The Interaction module
6. From the Edit Interaction dialog box, click OK to create the interaction.
Tip: You can also create a constraint using the tool in the Interaction module toolbox.
a. Name the constraint. For more information about naming objects, see ``Using basic dialog
box components,'' Section 6.3.1.
b. From the Type list, select Tie, and then click Continue.
· Use the mouse to select a region in the viewport. (For more information, see ``Selecting
objects within the current viewport, '' Section 9.2.) Click mouse button 2 to indicate you have
finished selecting. You must select a region from only one part instance; the region that you
select cannot span multiple part instances.
5-573
The Interaction module
Tip: You can limit the types of objects that you can select in the viewport by clicking the
selection filter tool in the prompt area and then clicking the selection filter of your
choice in the dialog box that appears. See ``Using the selection options,'' Section 9.3, for
more information.
If the model contains a combination of orphan mesh instances and native geometric part
instances, click one of the following from the prompt area:
- Click Geometry if you want to select the surface or vertex from a native geometric part
instance.
- Click Mesh if you want to select the surface or node from an orphan mesh instance.
If you are selecting a surface from an orphan mesh, you have the option of either selecting
individual element faces or specifying a face angle. See ``Using the face angle method to
create a surface from an orphan mesh,'' Section 9.2.3, for more information.
· Use an existing surface to define the region. On the right side of the prompt area, click
Surfaces. Select an existing surface from the Region Selection dialog box that appears, and
click Continue.
Note: The default selection method is based on the selection method you most recently employed. To revert to the other
method, click Select in Viewport or Surfaces on the right side of the prompt area.
· Select Node Region if you want to select a region from which to create a node-based surface.
Use one of the same methods described in the previous step to select the slave surface or region.
As with the master surface, the surface or region that you select cannot span multiple part
instances.
5. After you select the slave surface, the constraint editor appears. The Switch button allows you to
interchange your master and slave surface selections without having to start over.
In the constraint editor, choose the node adjustment method. For more information, see
``Adjusting initial surface positions and specifying initial clearances in contact pairs, '' Section
21.2.2 of the ABAQUS/Standard User's Manual and Section 20.2.2 of the ABAQUS/Explicit
User's Manual.
5-574
The Interaction module
Tip: You can also create a constraint using the tool in the Interaction module toolbox.
a. Name the constraint. For more information about naming objects, see ``Using basic dialog
box components,'' Section 6.3.1.
b. From the Type list, select Equation, and then click Continue.
The Edit Constraint dialog box appears.
3. In the table in the Edit Constraint dialog box, enter a row of data for each term in the equation.
The equation must have at least two terms. Click the Tip button for a description of the
relationship between the data in the table and the desired equation.
Each row should contain the following information:
· The coefficient.
· The name of an existing set. (For information on creating sets, see Chapter 45, "The Set and
Surface toolsets.") You can enter any set in the first row of the table. However, subsequent
rows must refer to sets that contain only a single vertex.
· The ID of the coordinate system in which you will apply the constraint. You can either accept
the default coordinate system or select an existing datum coordinate system. If the desired
datum coordinate system does not exist, you can create it using the Datum toolset. (For more
information, see ``Creating datum coordinate systems,'' Section 41.8.)
To determine the ID of a coordinate system, select Tools->Query from the main menu bar.
For more information, see ``Obtaining general information about the model,'' Section 44.2.2.
5-575
The Interaction module
4. When you have finished entering data, click OK to save your equation definition and to close the
Edit Constraint dialog box.
· ``Linear constraint equations,'' Section 20.2.1 of the ABAQUS/Standard User's Manual and
Section 19.2.1 of the ABAQUS/Explicit User's Manual
Tip: You can also create an interaction using the tool in the Interaction module
toolbox.
· Name the interaction. For more information about naming objects, see ``Using basic dialog
box components,'' Section 6.3.1.
4. From the assembly, select the point where the interaction will be applied. Click mouse button 2 to
indicate you have finished selecting the point.
Tip: You can limit the types of objects that you can select in the viewport by clicking the
5-576
The Interaction module
selection filter tool in the prompt area and then clicking the selection filter of your
choice in the dialog box that appears. See ``Using the selection options,'' Section 9.3, for more
information.
5. Enter the necessary data in the Edit Interaction dialog box. The required data are a function of
your user-defined element subroutine. You may need to create a real and integer actuator/sensor
interaction properties. For more information, see ``Creating interaction properties,'' Section 18.8.2.
The following table indicates the correspondence between the fields in the Edit Interaction dialog
box and the variables in user subroutine UEL.
Field UEL variable
User element type id JTYPE
Degrees of freedom NDOFEL
Number of coordinate components MCRD
Solution-dependent state variables SVARS and NSVARS
The real and integer values entered into an actuator/sensor interaction property are used by the
PROPS, JPROPS, NPROPS, and NJPROPS variables. For a description of all the variables that can
be passed into user subroutine UEL, see ``User-defined elements,'' Section 18.8.1 of the
ABAQUS/Standard User's Manual.
1. If you are editing an interaction, select from the Step list located under the toolbar the step in
which the interaction was created.
2. From the Interaction or Constraint menu in the main menu bar, select Edit->interaction or
constraint name of your choice . For example, to edit an interaction, you would select
Interaction->Edit->interaction name.
Tip: You can also initiate this procedure using the following methods:
5-577
The Interaction module
In the Interaction Manager, click the cell located in the row of the interaction that
you want to modify and in the column of the step in which it was created, and click
Edit. Alternatively, you can just double-click the cell.
If you are editing a foundation interaction, either you are prompted to edit the region by selecting
or unselecting objects in the viewport or a Region Selection dialog box appears in which you can
select a surface that you have already created using the Surface toolset.
If you are editing any other type of interaction or a constraint, the appropriate editor appears. The
editor contains an Edit Region button for each region involved in the interaction or constraint
definition.
3. If you are editing a constraint or any type of interaction other than foundation, click Edit Region
for the region that you want to modify. For example, if you are editing a surface-to-surface contact
interaction and you want to modify the master surface, click Edit Region next to the Master
surface label in the editor.
4. Edit the region by selecting and unselecting objects in the viewport. When you have finished
editing the region, click mouse button 2. (For more information, see Chapter 9, "Selecting objects
within the viewport.")
Tip: You can limit the types of objects that you can select in the viewport by clicking the
selection filter tool in the prompt area and then clicking the selection filter of your
choice in the dialog box that appears. See ``Using the selection options,'' Section 9.3, for more
information.
If you would rather select from a list of existing sets or surfaces, do the following:
a. Click Sets or Surfaces on the right side of the prompt area. (The name of the button
depends on the type of object you are editing. For example, if you are editing an
interaction, a Surfaces button appears.)
ABAQUS/CAE displays the Region Selection dialog box containing a list of available
sets or surfaces.
5. Finish editing the interaction or constraint definition as desired, and then press mouse button 2 (if
you are editing a foundation interaction) or click OK in the editor (if you are editing any other type
5-578
The Interaction module
5-579
The Load/BC/IC module
· Loads
· Boundary conditions
· Initial conditions
The tutorial will help you become familiar with techniques for creating and applying prescribed
conditions.
· ``Prescribed conditions: overview,'' Section 19.1.1 of the ABAQUS/Standard User's Manual and
Section 18.1.1 of the ABAQUS/Explicit User's Manual
6-580
The Load/BC/IC module
The Create, Edit, Copy, Rename, and Delete buttons in the managers allow you to create new
prescribed conditions or to edit, copy, rename, and delete existing ones. You can also initiate the
create, edit, copy, rename, and delete procedures by using the Load, BC, and IC menus in the main
menu bar. After you select a management operation from the main menu bar, the procedure is exactly
the same as if you had clicked the corresponding button inside the manager dialog box.
The decision whether to use the menu or the manager dialog box is yours. In general, the menu is more
convenient if you are performing isolated operations; the advantages of the manager dialog box
become apparent when you are performing several operations in sequence or when you need to browse
through a long list of prescribed conditions.
The load and boundary condition managers are step-dependent managers, which means that they
6-581
The Load/BC/IC module
contain additional information concerning the history of each load and boundary condition in the
model. These managers also contain buttons that allow you to manipulate the history of prescribed
conditions. (For more information, see ``What are step-dependent managers?,'' Section 6.5.2.) The
step-dependent Load Manager is shown in Figure 19-2.
For detailed instructions on creating, editing, and manipulated prescribed conditions, see the following
sections:
· ``Entering concentrated force data in the load editor, '' Section 19.7.5
· ``Understanding methods for defining Displacement/Rotation boundary conditions, '' Section 19.7.9
· ``Defining a constant initial temperature through a shell section, '' Section 19.7.15
· ``Defining initial temperatures at points through a shell or beam section, '' Section 19.7.16
· ``Defining an initial temperature gradient through a shell section, '' Section 19.7.17
· ``Editing the region to which a prescribed condition is applied, '' Section 19.7.19
6-582
The Load/BC/IC module
See also ``What are step-dependent managers?,'' Section 6.5.2, for information on managing
step-dependent objects.
This editor contains special text fields in which you can specify the components of the force in the 1-,
6-583
The Load/BC/IC module
2-, and 3-directions. The editor also contains an Amplitude text field that allows you to vary the
magnitude of the prescribed condition as a function of time. You can accept either the default
amplitude or select an amplitude that you have defined using the Amplitude toolset. (For more
information, see Chapter 40, "The Amplitude toolset.")
In the case of displacement/rotation and velocity/angular velocity boundary conditions you can specify
the coordinate system in which you will apply the boundary condition. You can accept either the
default coordinate system or select an existing datum coordinate system. If the desired datum
coordinate system does not exist, you can create it using the Datum toolset. (For more information, see
``Creating datum coordinate systems,'' Section 41.8.)
Note: If you delete or suppress the datum coordinate system, the orientation of the boundary
condition reverts to the global coordinate system.
Once you have created a prescribed condition, you can modify the prescribed condition in the
following ways:
· You can modify some or all of the data that you entered in the editor when you created the
prescribed condition.
· In the case of loads and boundary conditions, you can use the managers to modify the stepwise
history of the prescribed condition. (For more information, see ``What are step-dependent
managers?,'' Section 6.5.2.)
To display help on a particular manager or editor feature, select Help->On Context from the main
menu bar and then click the feature of interest.
· If applicable, the direction (negative or positive) in which you applied the prescribed condition.
6-584
The Load/BC/IC module
This section explains how to interpret the symbols. The following topics are covered:
· ``Understanding prescribed condition symbol type and color, '' Section 19.5.1
For information about controlling the visibility of these symbols, see ``Controlling the display of loads,
boundary conditions, and initial conditions, '' Section 46.8.
The following tables summarize the significance of the symbol types and colors:
Loads Symbol Color
Force and Bolt Arrow Yellow
Pressure Arrow Violet
Surface heat flux Arrow Green
Boundary conditions Symbol Color
Displacement/Rotation Arrow Orange for components applied to
degrees of freedom 1-3.
Blue for components applied to
degrees of freedom 4-6.
Symmetry/Antisymmetry/E Arrow Orange for components applied to
ncastre degrees of freedom 1-3.
Blue for components applied to
degrees of freedom 4-6.
Velocity/Angular velocity Arrow Sandy brown for components
applied to degrees of freedom 1-3.
Magenta for components applied to
degrees of freedom 4-6.
Temperature Cube Yellow
Initial conditions Symbol Color
Translational velocity Arrow Sandy brown
Constant temperature over Cube Yellow
region
For example, Figure 19-4 displays a concentrated force applied to vertices. All of the arrows that
represent the different components of the concentrated force are yellow.
6-585
The Load/BC/IC module
On the other hand, Figure 19-5 shows a Velocity/Angular Velocity boundary condition that is applied
to both translational and rotational degrees of freedom. The sandy brown arrows represent components
of the boundary condition that are applied to translational degrees of freedom. The magenta arrows
represent components of the boundary condition that are applied to rotational degrees of freedom.
Note: When a boundary condition fixes a degree of freedom in place, the arrow representing that
component lacks a stem.
· ``Controlling the display of loads, boundary conditions, and initial conditions, '' Section 46.8
6-586
The Load/BC/IC module
In most cases ABAQUS/CAE uses arrows to represent prescribed conditions in the viewport. These
arrows represent each component of the prescribed condition. The size of the arrows is uniform and
unrelated to the magnitude of the prescribed condition.
For example, the arrows that appear in Figure 19-6 represent the three components of a concentrated
force that is applied to two vertices.
An arrow with a single arrow head represents a component of a prescribed condition that is applied to
a translational degree of freedom. For example, the three components of the concentrated force in
Figure 19-6 are applied to degrees of freedom 1 through 3; therefore, each arrow in the figure has a
single arrow head.
When a component of a prescribed condition is applied to a rotational degree of freedom, that
component appears as a double-headed arrow. The arrows in Figure 19-7 indicate that a
Velocity/Angular Velocity boundary condition is applied to degrees of freedom 4 and 6 of the
vertices.
6-587
The Load/BC/IC module
If you apply a prescribed condition to both translational and rotational degrees of freedom, both the
single-headed and the double-headed arrows appear. For example, a Velocity/Angular Velocity
boundary condition is applied to degrees of freedom 1, 3, 4, and 6 of the vertex in Figure 19-9.
Figure 19-9 Magnified view of a boundary condition applied to translational and rotational degrees of
freedom.
In this figure the single-headed arrows are sandy brown and indicate that degrees of freedom 1 and 3 of
the vertex are fixed. The double-headed arrows are magenta and appear directly behind the
single-headed arrows; the double-headed arrows indicate that degrees of freedom 4 and 6 of the vertex
are fixed.
For information on arrow color, see ``Understanding prescribed condition symbol type and color, ''
Section 19.5.1. For information on when to expect arrows to point toward or away from a region, see
``Understanding symbol location and direction,'' Section 19.5.3.
· ``Controlling the display of loads, boundary conditions, and initial conditions, '' Section 46.8
6-588
The Load/BC/IC module
6-589
The Load/BC/IC module
When a boundary condition fixes a degree of freedom in place, the arrow representing that component
points into the region and lacks a stem. For example, the boundary condition in Figure 19-12 fixes
degrees of freedom 1, 2, and 3 in place.
Likewise, if a positive pressure load is applied to a region, the arrows representing that pressure load
point into the region, as illustrated in Figure 19-13.
In all other cases, arrows representing components of a prescribed condition point out from the region.
Note: When a component of a concentrated force is zero, no arrow appears for that component.
6-590
The Load/BC/IC module
Likewise, when a boundary condition leaves a degree of freedom unconstrained, no arrow appears
for that component.
· ``Controlling the display of loads, boundary conditions, and initial conditions, '' Section 46.8
In this tutorial you will fix the clamp in place by applying a boundary condition to the end of the
clamp, and you will apply a pressure load to the top of the clamp. In addition, you will use managers to
manipulate the stepwise history of the boundary condition and load.
6-591
The Load/BC/IC module
3. Click the File type arrow, and select Model Database (*.cae) if it is not already selected.
4. In the Selection field at the bottom of the Open Database dialog box, delete the default text and
type the path of the file containing the model database.
5. Click OK.
ABAQUS/CAE reads the model database containing the clamp model.
· Use a combination of the view manipulation tools and the display option tools in the toolbar and the tools in the Views
toolbox to resize and reposition the model as necessary. (The Views toolbox appears when you select from the
toolbar.)
In particular, you will probably find the magnification tool and the rotation tool useful for displaying the
model at a convenient size and orientation.
· When necessary, click the Iso tool in the Views toolbox to return the model to its original size and position in
the viewport.
For more information on the view manipulation tools, see Chapter 8, "Manipulating the view and controlling perspective."
b. Select Step-1 as the step in which the load is first applied to the model.
6-592
The Load/BC/IC module
e. Click Continue.
5. To select the surface to which the pressure load will be applied, click the top face of the clamp in
the ABAQUS/CAE viewport. The desired face is shown in Figure 19-15.
8. Accept the default distribution setting of Uniform and the default Amplitude value.
6-593
The Load/BC/IC module
For example, the Load Manager above indicates that you have activated (created) the load
Pressure in Step-1 and that it remains in effect through Step-2 and Step-3. ABAQUS/CAE
managers that display information about an object's status in each step of an analysis are called
step-dependent managers. This type of manager also contains a series of buttons that allow you to
change the stepwise history of an object.
In this section you will use the buttons in the Load Manager to activate the load Pressure in Step-2
of the analysis rather than in Step-1, and you will deactivate the load in Step-3.
To alter the status of the load:
1. In the Load Manager, click the cell labeled Created in the column labeled Step-1.
That cell becomes highlighted.
3. In the Load Manager, click the cell labeled Propagated in the column labeled Step-3.
That cell becomes highlighted.
4. Click Deactivate.
The Propagated status in Step-3 changes to Inactive.
6-594
The Load/BC/IC module
1. In the Load Manager, click the cell labeled Created in the column labeled Step-2. Then click
Edit.
The region to which the load is currently applied is highlighted in the viewport.
3. In the viewport, select both the bottom and the top faces of the clamp, as shown in Figure 19-17.
By default, when you click in a region that overlaps more than one face, ABAQUS/CAE selects
the face that is "closest" to the screen. To select the bottom surface of the clamp, you need to turn
off the default behavior and cycle through the valid selections.
b. In the dialog box, identify the Select the Entity Closest to the Screen tool by holding
6-595
The Load/BC/IC module
the cursor briefly over each button in the dialog box; toggle off this tool.
5. In the Edit Load dialog box, change the magnitude of the load from 500 to 5000. Then click OK
to save your changes and to close the editor.
A pressure load of magnitude 5000 is now applied to both the top and bottom faces. Violet arrows
point into both surfaces, indicating that a positive pressure load is applied to each surface.
6-596
The Load/BC/IC module
d. From the Type for Selected Step list, accept the default selection of
Displacement/Rotation .
e. Click Continue.
3. In the viewport, select the face at the end of the clamp. The desired face is shown in Figure 19-18.
Again, you will have to turn off the default selection behavior and cycle through the valid
selections to choose the end surface of the clamp.
5. In the Edit Boundary Condition dialog box, accept the default coordinate system of Global.
6. Toggle on the check boxes labeled U1, U2, and U3 to constrain these degrees of freedom.
· ``Understanding methods for defining Displacement/Rotation boundary conditions, '' Section 19.7.9
6-597
The Load/BC/IC module
The following list summarizes the key points demonstrated in this tutorial:
· When you define a load or boundary condition, you must specify the following:
- The region to which you want to apply the load or boundary condition.
· You can use the Load Manager or the Boundary Condition Manager to view and, in some
cases, manipulate the stepwise history of a load or boundary condition.
· When you apply a prescribed condition to a model, symbols representing that prescribed condition
appear in the viewport.
· ``Entering concentrated force data in the load editor, '' Section 19.7.5
· ``Understanding methods for defining Displacement/Rotation boundary conditions, '' Section 19.7.9
· ``Defining a constant initial temperature through a shell section, '' Section 19.7.15
· ``Defining initial temperatures at points through a shell or beam section, '' Section 19.7.16
· ``Defining an initial temperature gradient through a shell section, '' Section 19.7.17
6-598
The Load/BC/IC module
· ``Editing the region to which a prescribed condition is applied, '' Section 19.7.19
See also ``What are step-dependent managers?,'' Section 6.5.2, for information on managing loads and
boundary conditions.
1. If you are creating a load or boundary condition, click in the Step list located under the toolbar
and select the step in which you want to activate the load or boundary condition.
2. Select Create from the appropriate menu in the main menu bar or click Create in the appropriate
manager.
3. In the Create dialog box that appears, specify information about the type of prescribed condition
you want to create.
5. In the editor that appears or, if applicable, in the prompt area, enter any data necessary to define
the prescribed condition.
For detailed instructions for performing each of these tasks, see the procedures in the following
sections:
6-599
The Load/BC/IC module
prescribed condition you want to create as well as the step in which you want to activate it.
Detailed instructions for starting the procedure to create a prescribed condition:
1. If you are creating a load or boundary condition, click in the Step list located under the toolbar
and select the step in which you want to activate the load or boundary condition. (This action is
unnecessary if you are creating an initial condition, because initial conditions are not associated
with a particular step.)
Tip: If you are creating a load or boundary condition, you can wait to select a step using the
Create dialog box that appears in Step 2 of this procedure; see Step 3 of this procedure for
details.
2. In the main menu bar, select Create from the appropriate menu. For example, if you want to create
a load, select Load->Create.
A Create dialog box appears with a default name displayed in the Name text field.
Tip: You can initiate the Create procedure in two other ways:
· Click Create in the manager associated with the type of prescribed condition you are
creating.
· Click the appropriate tool in the Load/BC/IC module toolbox. To see a short description
of each tool, briefly hold the cursor over the tool icon.
a. Type a name for the prescribed condition that you are creating. For more information on
naming objects, see ``Using basic dialog box components,'' Section 6.3.1.
b. If you are creating a load or boundary condition and have not already selected the step in
which you want to activate the prescribed condition, click the arrow next to the Step text
field and select the step of your choice from the list that appears.
c. From the Category list on the left side of the dialog box, select the category of your
choice.
The Type for Selected Step list on the right side of the dialog box changes to list all of
the prescribed condition type within the category you choose.
d. From the Type for Selected Step list on the right side of the dialog box, select the type of
your choice.
e. Click Continue.
You are prompted to select the region to which to apply the prescribed condition. For
more information, see ``Applying a prescribed condition to a region,'' Section 19.7.3.
6-600
The Load/BC/IC module
1. Begin the procedure for creating a prescribed condition, as described in ``Starting the procedure to
create a prescribed condition,'' Section 19.7.2.
2. If the model contains a combination of orphan mesh instances and native part instances, you must
choose the part type to which you want to apply the prescribed condition. From the buttons in the
prompt area select one of the following:
· Click Geometry if you want to apply the prescribed condition to a native part instance.
· Click Mesh if you want to apply the prescribed condition to an orphan mesh instance.
3. Use the mouse to select a region in the viewport. When you have finished selecting, click mouse
button 2. (For more information, see Chapter 9, "Selecting objects within the viewport.")
Tip: You can limit the types of objects that you can select in the viewport by clicking the
selection filter tool in the prompt area and then clicking the selection filter of your
choice in the dialog box that appears. See ``Using the selection options,'' Section 9.3, for more
information.
If you are selecting a surface from an orphan mesh, you have the option of either selecting
individual element faces or specifying a face angle. See ``Using the face angle method to create a
surface from an orphan mesh,'' Section 9.2.3, for more information.
If you would rather select from a list of existing sets or surfaces, do the following:
a. Click Sets or Surfaces on the right side of the prompt area. (The name of the button
depends on the type of prescribed condition you are creating. For example, if you are
creating a pressure load, a Surfaces button appears.)
ABAQUS/CAE displays the Region Selection dialog box containing a list of available
sets or surfaces.
b. Select the set or surface to which you want to apply the prescribed condition, and click
Continue.
6-601
The Load/BC/IC module
Note: The default selection method is based on the selection method you most recently employed. To revert to the other
method, click Select in Viewport or Sets or Surfaces on the right side of the prompt area.
Depending on the prescribed condition you are defining, either an editor appears or you are
prompted to enter data directly in the prompt area. The region to which you are applying the
prescribed condition is highlighted in the viewport. For more information, see ``Specifying
prescribed condition data,'' Section 19.7.4.
1. Begin the procedure for creating a prescribed condition, as described in ``Starting the procedure to
create a prescribed condition,'' Section 19.7.2.
2. Select the region to which to apply the prescribed condition, as described in ``Applying a
prescribed condition to a region,'' Section 19.7.3.
3. Enter data concerning the prescribed condition in one of the following ways:
6-602
The Load/BC/IC module
In the editor that appears, enter all of the data necessary to define the object and then click
OK. (For detailed information on a particular feature of the editor, select Help->On
Context from the main menu bar and then click the feature of interest.)
Symbols appear in the viewport that represent the prescribed condition that you just created. For
more information, see ``Understanding symbols that represent prescribed conditions, '' Section
19.5.
1. Display the load editor. For more information, see ``Creating prescribed conditions,'' Section
19.7.1, or ``Editing step-dependent objects,'' Section 6.5.9.
2. In the CF1, CF2, and (if you are working with a model in three-dimensional space) CF3 text fields,
enter the components of the concentrated force in the 1-, 2-, and (if applicable) 3-directions.
If you leave a text field blank, a force of zero is assigned to that direction automatically. However,
you must enter at least one non-zero component in the editor to define the load.
3. Click the arrow to the right of the Amplitude text field. Select the amplitude of your choice from
the list that appears.
· ``Concentrated and distributed loads, '' Section 19.4.2 of the ABAQUS/Standard User's Manual and
6-603
The Load/BC/IC module
1. Display the load editor. For more information, see ``Creating prescribed conditions,'' Section
19.7.1, or ``Editing step-dependent objects,'' Section 6.5.9.
2. Click the Distribution menu button, and select the option of your choice from the list that
appears.
Nonuniform distributed loads must be defined in user subroutine DLOAD (for ABAQUS/Standard)
or VDLOAD (for ABAQUS/Explicit). See the following sections for more information:
3. In the Component 1, Component 2, and (if you are working with a model in three-dimensional
space) Component 3 text fields, enter the components of the body force in the 1-, 2-, and (if
applicable) 3-directions.
If you leave a text field blank, a force of zero is assigned to that direction automatically. However,
you must enter at least one nonzero component in the editor to define the load.
4. Click the arrow to the right of the Amplitude text field. Select the amplitude of your choice from
the list that appears.
· ``Concentrated and distributed loads, '' Section 19.4.2 of the ABAQUS/Standard User's Manual and
Section 18.4.2 of the ABAQUS/Explicit User's Manual
6-604
The Load/BC/IC module
When you define loads, you can specify data for uniform loading directly in the load editor.
Alternatively, if you are defining a pressure load, a body force, or a surface heat flux load, you can
specify data for nonuniform loading by referring to a user subroutine.
Detailed instructions for defining a uniform or nonuniform load:
1. Display the load editor. For more information, see ``Creating prescribed conditions,'' Section
19.7.1, or ``Editing step-dependent objects,'' Section 6.5.9.
2. From the Distribution menu button, select one of the following options:
· Select Uniform to define a load that is uniform over the surface to which it is applied.
3. If you selected Uniform, enter any data necessary to define the load, and then click OK.
a. If desired, enter default data and then click OK. (If you prefer, you can specify this data in
the user subroutine file to which you will refer.)
b. Enter the Job module and display the job editor for the analysis job of interest. (For more
information, see ``Creating, editing, and manipulating jobs,'' Section 21.3.)
c. In the job editor, click the General tab, and specify the file containing the user subroutine
that defines the variation in load magnitude:
· If you are defining a nonuniform pressure load or body force, you must provide a
DLOAD (for ABAQUS/Standard) or VDLOAD (for ABAQUS/Explicit) user subroutine.
(For more information, see ``DLOAD,'' Section 23.2.5 of the ABAQUS/Standard
User's Manual, or ``VDLOAD,'' Section 21.2.1 of the ABAQUS/Explicit User's
Manual.)
· If you are defining a nonuniform surface heat flux, you must provide a DFLUX user
subroutine. (For more information, see ``DFLUX,'' Section 23.2.3 of the
ABAQUS/Standard User's Manual.)
For more information, see ``Specifying general job settings,'' Section 21.4.6.
Note: You can specify only one user subroutine file in the job editor; if your analysis involves more than one
user subroutine, you must combine the user subroutines into one file and then specify that file.
6-605
The Load/BC/IC module
· ``Concentrated and distributed loads, '' Section 19.4.2 of the ABAQUS/Standard User's Manual and
Section 18.4.2 of the ABAQUS/Explicit User's Manual
You can model the tension in the tightened bolts by applying a bolt load to each one in the first step of
the analysis. You define the load in terms of either a concentrated force or a prescribed change in
length, and you apply the load across a bolt cross-section surface that you specify. In later steps you
can modify the load to prevent further length changes so that the bolt acts as a standard, deformable
component responding to other loadings on the assembly.
When you create a bolt load, you must specify the following:
6-606
The Load/BC/IC module
If you are working with an orphan mesh part, you must specify the cross-section surface by
selecting element faces. For example, element faces define a cross-section surface for the
orphan mesh shown below:
For more information on selecting surfaces, see Chapter 9, "Selecting objects within the
viewport." For detailed information on selecting surfaces on wire part instances, see
``Specifying a particular side or end of a region,'' Section 45.2.5.
Note: Currently you can apply bolt loads only to solid and wire part instances. Bolt loads
on two-dimensional and axisymmetric part instances are unsupported.
A bolt axis
If you are defining a bolt load on a solid region, you must define a datum axis that indicates
the bolt axis direction (it need not be normal to the cross- section). If you are defining a bolt
load on a wire region, the bolt axis direction is always assumed to be the direction of the
tangent to the wire at the bolt cross-section.
ABAQUS/CAE uses both the cross-section surface that you specify and bolt axis to define the
*PRE-TENSION SECTION option data and the pre-tension reference node used by the solver.
(See ``Prescribed assembly loads,'' Section 19.5.1 of the ABAQUS/Standard User's Manual,
for more information.)
6-607
The Load/BC/IC module
· Apply a force to the bolt. This method models tightnening the bolt so that it carries a
specified load. Using this method is analogous to including the *CLOAD option in the
analysis input file to apply a load to the pre-tension reference node.
· Adjust the bolt length. This method models tightening the bolt until its free length has
changed by the specified value. Using this method is analogous to including the
*BOUNDARY option in the analysis input file to apply a boundary condition to degree of
freedom 1 of the pre-tension reference node.
· Fix the bolt at its current length. This method is available only if you have aready created
the load in the first analysis step and are now editing it an a subsequent analysis step. This
method allows the bolt length to remain unchanged so that the force in the bolt can change
according to the response of the model. Using this method is analogous to including the
*BOUNDARY, FIXED option in the analysis input file to apply a boundary condition to
the pre-tension reference node that fixes the bolt length.
You can create a bolt load only in the first analysis step, but you can modify the loading method or the
magnitude of the load in subsequent steps. For example, you can apply a specific tension in the first
step and then change the method in the second step to fix the bolt length.
Detailed instructions for defining bolt loads:
1. If you are working with native or imported geometry, create a partition that indicates the desired
location of the bolt load. For more information, see Chapter 43, "The Partition toolset."
2. If you are working with a solid part instance, create a datum axis that indicates the desired
orientation of the bolt axis. (For more information, see ``Creating datum axes,'' Section 41.6.)
b. From the Type for Selected Step list, select Bolt Load, and click Continue.
5. In the viewport, use the mouse to select the surface that indicates the location of the bolt load.
When you have finished selecting, click mouse button 2. (For more information, see Chapter 9,
6-608
The Load/BC/IC module
"Selecting objects within the viewport." For detailed information on selecting surfaces on wire part
instances, see ``Specifying a particular side or end of a region,'' Section 45.2.5.)
Tip: You can limit the types of objects that you can select in the viewport by clicking the
selection filter tool in the prompt area and then clicking the selection filter of your
choice in the dialog box that appears. See ``Using the selection options,'' Section 9.3, for more
information.
If you are selecting a surface from an orphan mesh, you have the option of either selecting
individual element faces or specifying a face angle. See ``Using the face angle method to create a
surface from an orphan mesh,'' Section 9.2.3, for more information.
If you would rather select from a list of surfaces that you have defined using the Surface toolset, do
the following:
If the bolt is modeled with wire or axisymmetric part instances, ABAQUS/CAE displays the bolt
load editor when you have finished selecting the cross- section surface. If the bolt is modeled with
solid part instances, you are prompted to select a datum axis.
6. If the bolt is modeled with solid part instances, select a datum axis that indicates the desired
direction of the bolt axis.
ABAQUS/CAE displays the bolt load editor.
7. Click the arrow next to the Method field and select the loading method of your choice from the list
that appears.
8. In the Magnitude field, enter the force magnitude (for the Apply force method) or the change in
length (for the Length method).
Note: The Fix at current length method becomes available if you edit the load in a step that
follows the step in which you create the load. If, while editing the load, you change the method
to Fix at current length, the Magnitude field becomes unavailable.
9. If desired, specify an amplitude. (See Chapter 40, "The Amplitude toolset," for more information.)
10. If you are creating a bolt load on a solid part instance or if you are editing a bolt load on a solid
part instance in the first analysis step, an Edit axis button appears at the bottom of the editor.
6-609
The Load/BC/IC module
Click Edit axis if you want to change your datum axis selection.
11. Click OK to create the load and to close the Create Bolt Load dialog box.
Arrows appear in the viewport that represent the bolt load that you just created. For more
information, see ``Understanding symbols that represent prescribed conditions, '' Section 19.5.
Fix the degrees of freedom at their final values from the previous general step.
You can choose between the two methods only if both are valid for the step in which the boundary
condition is created. When the editor offers you a choice of methods, the Specify Constraints method
is selected by default.
For information about creating boundary conditions using the different editor formats, see ``Entering
boundary condition values for degrees of freedom,'' Section 19.7.10, and ``Fixing degrees of freedom
at their current values,'' Section 19.7.11.
· ``Boundary conditions,'' Section 19.3.1 of the ABAQUS/Standard User's Manual and Section
18.3.1 of the ABAQUS/Explicit User's Manual
6-610
The Load/BC/IC module
1. Display the appropriate boundary condition editor. (For more information, see ``Creating
prescribed conditions,'' Section 19.7.1, or ``Editing step-dependent objects,'' Section 6.5.9.)
2. If a Method menu button appears toward the top of the editor, click the menu button and select
Specify Constraints from the menu that appears. (The Method button will not appear if only one
method is valid for the step in which you are creating the boundary condition.)
Text fields appear to the right of each degree of freedom. If you are creating a new boundary
condition, all the buttons are toggled off, indicating that all the degrees of freedom are
unconstrained.
3. If you are creating either a displacement/rotation or a velocity/angular boundary condition you can
specify the coordinate system in which you will apply the boundary condition. You can accept
either the default coordinate system or select an existing datum coordinate system. If the desired
datum coordinate system does not exist, you can create it using the Datum toolset. (For more
information, see ``Creating datum coordinate systems,'' Section 41.8.)
· Toggle a button on to constrain a degree of freedom. The text field becomes available in which
you can specify a value for the degree of freedom. If you are creating the boundary condition
in this step, a default value of zero appears in the text field. If you are modifying the boundary
condition in this step, the value propagated from the previous step appears in the text field.
· Toggle a button off to leave the degree of freedom unconstrained. If you toggle a button off
after modifying the default or propagated value in the text field, the modified value is lost. If
you toggle that button back on, the default or propagated value reappears in the text field.
· ``Understanding methods for defining Displacement/Rotation boundary conditions, '' Section 19.7.9
6-611
The Load/BC/IC module
· ``Boundary conditions,'' Section 19.3.1 of the ABAQUS/Standard User's Manual and Section
18.3.1 of the ABAQUS/Explicit User's Manual
· If you are defining the boundary condition in the initial step or in the first analysis step, the degree
of freedom is fixed at zero.
· If you are defining the boundary condition in one of the analysis steps that follows the first
analysis step, the degree of freedom is fixed at its final value from the previous analysis step.
Using this method to define a boundary condition is analogous to including the *BOUNDARY,
FIXED option in a solver input file.
Detailed instructions for fixing the degrees of freedom at their current values:
1. Display the displacement/rotation boundary condition editor. (For more information, see
``Creating prescribed conditions,'' Section 19.7.1, or ``Editing step-dependent objects,'' Section
6.5.9.)
2. If a Method menu button appears toward the top of the editor, click the menu button and select
Fixed at Current Position from the menu that appears. (The Method button will not appear if
only one method is valid for the step in which you are creating the boundary condition.)
The data entry areas to the right of each degree of freedom disappear.
3. Specify the coordinate system in which you will apply the boundary condition. You can accept
either the default coordinate system or select an existing datum coordinate system. If the desired
datum coordinate system does not exist, you can create it using the Datum toolset. (For more
information, see ``Creating datum coordinate systems,'' Section 41.8.)
4. On the left side of the editor, toggle the buttons on or off to constrain or release each degree of
freedom:
· Toggle a button on if you want to fix the degree of freedom either at zero (if you are defining a
degree of freedom in the initial step or in the first analysis step) or at its final value at the end
of the previous analysis step (if you are defining the degree of freedom in the second analysis
step or in a later step.)
· Toggle a button off if you want to leave the degree of freedom unconstrained.
6-612
The Load/BC/IC module
· ``Understanding methods for defining Displacement/Rotation boundary conditions, '' Section 19.7.9
· ``Boundary conditions,'' Section 19.3.1 of the ABAQUS/Standard User's Manual and Section
18.3.1 of the ABAQUS/Explicit User's Manual
1. Display the boundary condition editor. See ``Creating prescribed conditions,'' Section 19.7.1, or
``Editing step-dependent objects,'' Section 6.5.9 for more information.
2. In the Degrees of freedom field, enter the temperature degrees of freedom that you want to
specify. For information on how shell temperature degrees of freedom are labeled, see either
``Heat transfer shell elements'' or ``Coupled temperature-displacement shell elements '' in
``Choosing a shell element,'' Section 15.6.2 of the ABAQUS/Standard User's Manual.
You can enter multiple degrees of freedom by separating each number with a comma. For
example, if you want to specify degrees of freedom 11, 12, and 13, you must enter the following:
11,12,13
3. In the Magnitude field, enter the magnitude that you want to assign to the degrees of freedom
specified in the previous step.
6-613
The Load/BC/IC module
which you can enter all of the data necessary to define the initial condition. For detailed information
about individual procedures, see the following sections:
· ``Defining a constant initial temperature through a shell section, '' Section 19.7.15
· ``Defining initial temperatures at points through a shell or beam section, '' Section 19.7.16
· ``Defining an initial temperature gradient through a shell section, '' Section 19.7.17
Detailed instructions for defining initial velocities or initial temperatures by entering data in the
prompt area:
1. Begin the procedure for creating or editing an initial condition. (For more information, see
``Creating prescribed conditions,'' Section 19.7.1, or ``Managing objects using manager dialog
boxes,'' Section 6.5.6.)
2. In the text field that appears in the prompt area, enter the requested information.
4. If additional text fields appear, repeat Steps 2 and 3 until the initial temperature or initial velocity
definition is complete.
· ``Initial conditions,'' Section 19.2.1 of the ABAQUS/Standard User's Manual and Section 18.2.1 of
the ABAQUS/Explicit User's Manual
· ``Specifying temperature and field variables'' in ``Using the *SHELL SECTION option to define
the section behavior,'' Section 15.6.5 of the ABAQUS/Standard User's Manual and Section 14.4.4
of the ABAQUS/Explicit User's Manual
6-614
The Load/BC/IC module
1. Begin the procedure for creating an initial velocity (see ``Creating prescribed conditions,'' Section
19.7.1) or select IC->Edit->initial velocity of your choice from the main menu bar.
An Initial velocity text field appears in the prompt area. If you are editing the initial translational
velocity, a More Options button also appears in the prompt area.
2. In the Initial velocity text field, enter the components of the initial velocity in the 1-, 2-, and (if
you are working in three-dimensional space) 3-directions.
Enter the components in the text field using the following format:
v1,v2 or v1,v2,v3
Do not put parentheses around the components.
3. If you are editing the initial velocity and want to change the region to which it is applied, do the
following:
b. At the top of the editor, click Edit Region and follow the prompts that appear in the
prompt area. (For more information, see ``Editing the region to which a prescribed
condition is applied,'' Section 19.7.19.)
c. If desired, modify the values entered in the V1, V2, and (if you are working in
three-dimensional space) V3 text fields to specify the initial velocity in the 1-, 2-, and (if
applicable) 3-directions. (If you leave a text field blank, an initial velocity of zero is
assigned to that degree of freedom by default.)
4. If you have created or edited the initial velocity using the prompt area, press [Enter] or click
mouse button 2 to save your data.
· ``Initial conditions,'' Section 19.2.1 of the ABAQUS/Standard User's Manual and Section 18.2.1 of
the ABAQUS/Explicit User's Manual
6-615
The Load/BC/IC module
Use the prompt area to assign an initial temperature to a shell region that has a uniform temperature
through its thickness. Defining an initial temperature is analogous to including *INITIAL
CONDITIONS, TYPE=TEMPERATURE in a solver input file.
Detailed instructions for defining a constant initial temperature through a shell section:
1. Begin the procedure for creating an initial temperature through a shell section (see ``Creating
prescribed conditions,'' Section 19.7.1) or select IC->Edit->initial temperature from the main
menu bar.
An Initial Temperature text field appears in the prompt area.
2. In the Initial Temperature text field, enter the initial temperature of the shell region.
· ``Selecting a method for defining the temperature variation through the section, '' Section 15.9.3
· ``Initial conditions,'' Section 19.2.1 of the ABAQUS/Standard User's Manual and Section 18.2.1 of
the ABAQUS/Explicit User's Manual
· ``Specifying temperature and field variables'' in ``Using the *SHELL SECTION option to define
the section behavior,'' Section 15.6.5 of the ABAQUS/Standard User's Manual and Section 14.4.4
of the ABAQUS/Explicit User's Manual
1. Begin the procedure for creating an initial temperature at points through a shell section (see
``Creating prescribed conditions,'' Section 19.7.1) or select IC->Edit->initial temperature from the
main menu bar.
An Initial temperatures text field appears in the prompt area.
6-616
The Load/BC/IC module
2. In the Initial temperatures text field, enter the temperature at each temperature point.
Enter the temperatures in the following format:
t1,t2,t3,...tn
Do not use parentheses.
Note: For shells and beams, the number of temperature points in the initial temperature definition must correspond to the
number of temperature points specified in the section definition that you apply to the region (although the Load/BC/IC module
does not enforce this correspondence). For example, if you apply a shell section to the region that specifies two temperature
points, you must provide the temperatures at those two points in the initial temperature definition. For more information, see
``Selecting a method for defining the temperature variation through the section,'' Section 15.9.3.
· ``Selecting a method for defining the temperature variation through the section, '' Section 15.9.3
· ``Initial conditions,'' Section 19.2.1 of the ABAQUS/Standard User's Manual and Section 18.2.1 of
the ABAQUS/Explicit User's Manual
· ``Specifying temperature and field variables'' in ``Using the *SHELL SECTION option to define
the section behavior,'' Section 15.6.5 of the ABAQUS/Standard User's Manual and Section 14.4.4
of the ABAQUS/Explicit User's Manual
1. Begin the procedure for creating an initial temperature gradient through a shell section (see
``Creating prescribed conditions,'' Section 19.7.1) or select IC->Edit->initial temperature from the
main menu bar.
An Initial temperature text field appears in the prompt area.
2. In the Initial temperature text field in the prompt area, enter the initial temperature at the
6-617
The Load/BC/IC module
3. In the Gradient text field, enter the temperature gradient from the reference surface through the
section.
· ``Selecting a method for defining the temperature variation through the section, '' Section 15.9.3
· ``Initial conditions,'' Section 19.2.1 of the ABAQUS/Standard User's Manual and Section 18.2.1 of
the ABAQUS/Explicit User's Manual
· ``Specifying temperature and field variables'' in ``Using the *SHELL SECTION option to define
the section behavior,'' Section 15.6.5 of the ABAQUS/Standard User's Manual and Section 14.4.4
of the ABAQUS/Explicit User's Manual
1. Begin the procedure for creating an initial temperature gradient through a shell section (see
``Creating prescribed conditions,'' Section 19.7.1) or select IC->Edit->initial temperature from the
main menu bar.
An Initial temperature text field appears in the prompt area.
2. In the Initial temperature text field in the prompt area, enter the initial temperature at the
reference surface of the beam and then click the second mouse button.
6-618
The Load/BC/IC module
3. In the N1 gradient text field, enter the initial temperature gradient along the n1 axis of the beam
and then click the second mouse button.
An N2 gradient text field appears in the prompt area.
4. In the N2 gradient text field, enter the initial temperature gradient along the n2 axis of the beam.
5. Press [Enter] or click the second mouse button to save your data.
· ``Selecting a method for defining the temperature variation through the section, '' Section 15.9.3
· ``Initial conditions,'' Section 19.2.1 of the ABAQUS/Standard User's Manual and Section 18.2.1 of
the ABAQUS/Explicit User's Manual
· ``Specifying temperature and field variables'' in ``Using the *SHELL SECTION option to define
the section behavior,'' Section 15.6.5 of the ABAQUS/Standard User's Manual and Section 14.4.4
of the ABAQUS/Explicit User's Manual
1. If you are editing a load or boundary condition, in the Step list located under the toolbar, click the
step in which the prescribed condition was created.
2. From the Load, BC, or IC menu in the main menu bar, select Edit->prescribed condition. For
example, to edit a load you would select Load->Edit->prescribed condition.
Tip: You can also initiate this procedure using the following methods:
6-619
The Load/BC/IC module
Depending on the type of prescribed condition you are editing, either an editor appears or text
fields appear in the prompt area.
3. If text fields appear in the prompt area, click More Options on the right side of the prompt area to
display the corresponding editor. (For more information, see ``Using the More Options button,''
Section 6.2.3.)
5. Edit the region by selecting and unselecting objects in the viewport. When you have finished
editing the region, click mouse button 2. (For more information, see Chapter 9, "Selecting objects
within the viewport.")
Tip: You can limit the types of objects that you can select in the viewport by clicking the
selection filter tool in the prompt area and then clicking the selection filter of your
choice in the dialog box that appears. See ``Using the selection options,'' Section 9.3, for more
information.
If you would rather select from a list of existing sets or surfaces, do the following:
a. Click Sets or Surfaces on the right side of the prompt area. (The name of the button
depends on the type of object you are editing. For example, if you are editing an
interaction, a Surfaces button appears.)
ABAQUS/CAE displays the Region Selection dialog box containing a list of available
sets or surfaces.
6. In the editor, finish editing the prescribed condition definition as desired and then click OK.
The symbols representing the prescribed condition in the viewport change to appear on the newly
edited region.
6-620
The Load/BC/IC module
6-621
The Mesh module
The tutorial will help you become familiar with creating meshes in ABAQUS/CAE. For information on
editing the nodes and elements that comprise an orphan mesh, see ``Editing an orphan mesh,'' Section
14.22.
7-622
The Mesh module
· A tool for assigning ABAQUS/Standard and ABAQUS/Explicit element types to mesh elements.
The elements can belong either to a model that you created or to an imported orphan mesh.
· Tools for partitioning complex models into simple subregions that ABAQUS/CAE can mesh using
automatic techniques.
· Model coloring that indicates the meshing technique assigned to each region in the model.
7-623
The Mesh module
· ``Information provided by the verification tool and the Query toolset,'' Section 20.3.5
The remaining topics in this section provide basic information about each type of function.
· You can control the density of a mesh by creating seeds along the edges of the model to indicate
where the corner nodes of the elements should be located. For example, Figure 20-1 displays a
model with biased seeding along the top and left edges.
7-624
The Mesh module
· You can use the Partition toolset to divide part instances into smaller regions. The resulting
partitions introduce new edges that you can seed; therefore, you can combine partitioning and
seeding to gain additional control over the mesh generation process. You can also use partitioning
to create regions to which you can assign different element types. For example, you might want to
assign reduced-integration elements to some portions of your model and fully integrated elements
to others.
· You can control the shape of the mesh elements by selecting options in the Mesh Controls dialog
box, which you can display by selecting Mesh->Controls from the main menu bar. For example,
Figure 20-2 shows a model that has been meshed first with quadrilateral elements and then with
triangular elements.
· You can choose the element type that is assigned to the mesh by selecting options in the Element
Type dialog box, which you can display by selecting Mesh->Element Type from the main menu
bar.
7-625
The Mesh module
Structured meshing
Structured meshing gives you the most control over your mesh because it applies
preestablished mesh patterns to particular model topologies.
Most unpartitioned models are too complex to be meshed using preestablished mesh patterns.
However, you can often partition complex models into simple regions with topologies for
which structured meshing patterns exist. Figure 20-3 shows an example of a structured mesh.
Swept meshing
ABAQUS/CAE creates swept meshes by internally generating the mesh on an edge or face and
then extruding that mesh along a sweep path or revolving the mesh around an axis of
revolution. The result can be either a two-dimensional mesh created from an edge or a
three-dimensional mesh created from a face. Like structured meshing, swept meshing is
limited to models with specific topologies and geometries. Figure 20-4 shows an example of a
swept mesh.
7-626
The Mesh module
Free meshing
The free meshing technique is the most flexible meshing technique. It uses no preestablished
mesh patterns and can be applied to almost any model shape. However, free meshing provides
you with the least control over the mesh since there is no way to predict the mesh pattern.
Figure 20-5 shows an example of a free mesh.
ABAQUS/CAE uses different highlighting colors to indicate which meshing technique, if any, is
currently assigned to a region. For example, if a solid region is meshable using the structured meshing
technique, the region turns green when you enter the Mesh module; the green color indicates that the
structured meshing technique is assigned to that region by default. If a region is unmeshable using the
element shape currently assigned to it, the region turns orange when you enter the Mesh module.
You can change the meshability of a region by partitioning the region into smaller regions with simpler
topology or by changing the element shape assigned to that region.
7-627
The Mesh module
When the part instance is meshed, the skin elements and the three-dimensional elements share the
same nodes and mesh topology. You can use mesh controls to assign a different geometric order to the
skin elements and to the three-dimensional elements. For more information, see ``Assigning element
types to skin reinforcements,'' Section 20.5.5.
· Aspect ratio
· Angular deviation
7-628
The Mesh module
The Query toolset allows you to obtain information about meshes, nodes, and elements while using the
Mesh module. The following information is available from the Query toolset:
Point
Instance mesh
Element
· The element type that ABAQUS/CAE will use for the analysis.
· Nodal connectivity.
Region mesh
· The element type that ABAQUS/CAE will use for the analysis.
· The mesh algorithm and any options that were used to mesh the region.
· The number of logical corners in the region if ABAQUS/CAE used structured meshing to
mesh the region.
7-629
The Mesh module
For detailed, step-by-step instructions for using the verification tool and the Query toolset, see
``Verifying element quality,'' Section 20.17.1, and ``Obtaining mesh information,'' Section 20.17.2.
· ``Understanding the relationship between vertices and nodes, '' Section 20.4.5
Only minimal seeding is necessary if you do not have strict mesh requirements. For example, you can
seed just one edge of the part instance or region and then let ABAQUS/CAE use a similar element
7-630
The Mesh module
· Average element size along an edge. (If the edge length is not an integer multiple of the element
length, ABAQUS/CAE will change the element length slightly to obtain an integer number of
elements along the edge.)
· Bias ratio and number of elements desired along an edge. The bias ratio is the ratio of the largest
element to the smallest element along an edge. This method results in a nonuniform distribution of
elements along the edge as long as the bias ratio is not equal to one.
Seeds created by specifying an average element size for the entire part instance are called instance
seeds and appear in white; seeds created using the other three methods are called edge seeds and
appear in magenta. Edge seeds always override instance seeds; therefore, when you specify the average
element size for the entire part instance, instance seeds appear only on edges of the region that do not
already have edge seeds. New edges created by partitioning are given instance seeds by default.
When you seed an edge of a region that is assigned the swept or revolved mesh technique, the edge
seeding tools automatically propagate seeds from the selected edge to the matching edges in the region.
In other words, the seeds on the face or edge at the beginning of the sweep path are propagated
automatically to the face or edge at the end of the sweep path. Likewise, the seeds created on one edge
along the sweep path are propagated automatically to the other edges along the sweep path. For more
information, see ``What is swept meshing?,'' Section 20.10.1.
For detailed instructions on prescribing seed density, see the following sections:
· ``Defining seed density for the entire part instance,'' Section 20.14.1
7-631
The Mesh module
Unconstrained
This is the default setting. The number of elements along an edge can either increase or
decrease so that the mesh can become denser or coarser than is specified by the seeds.
Unconstrained seeds appear as open circles.
Partially constrained
The number of elements along an edge may be increased during mesh generation but cannot be
decreased. This constraint allows the mesh to become denser than is specified by the seeds but
no coarser. Partially constrained seeds appear as upward-pointing triangles.
Fully constrained
The number of elements specified by constrained seeds along an edge cannot be altered by the
mesh generation process. However, the location of the nodes might not correspond exactly
with the location of the seeds. You can apply this constraint only to edge seeds, not to instance
seeds. Fully constrained seeds appear as squares.
ABAQUS/CAE always creates a fully constrained seed at each geometric vertex of a region to
indicate that a finite element node will be positioned at each vertex.
In many cases the mesh generator must redistribute elements (and deviate from the number and
location of the seeds) to successfully generate a mesh. For the greatest likelihood of meshing success,
leave seeds unconstrained or at least avoid fully constraining large numbers of seeds in a given part
instance so that the mesh generator has as much freedom to redistribute seeds as possible.
For detailed instructions on constraining seeds, see the following sections :
7-632
The Mesh module
· ``Relaxing constraints using the error dialog box, '' Section 20.14.9
ABAQUS/CAE tries to adhere as closely as possible to the number and location of seeds that you
specified when balancing the element redistribution for the entire model. If given a choice between
making a large change along a single seeded edge and making a small change to many edges,
ABAQUS/CAE will make many small changes.
7-633
The Mesh module
Note the locations of the nine vertices. These vertices were created by sketching several line segments
along the top and bottom edges rather than one continuous line segment along each edge.
When an instance of that part is seeded, square-shaped, fully constrained seeds appear at each vertex,
as shown in Figure 20-9.
When the model is meshed, ABAQUS/CAE always places nodes at the location of the fully
constrained seeds that are located at vertices, as shown in Figure 20-10.
Likewise, Figure 20-11 shows the sketch of two concentric circles that will be extruded to form a
hollow cylinder. Note the location of the vertices, which the Sketcher creates at the locations you click
to define the circles' perimeters.
7-634
The Mesh module
When the cylinder is seeded, square-shaped, fully constrained seeds appear at each vertex, as shown in
Figure 20-12.
When the model is meshed, nodes always appear at the location of the fully constrained seeds that are
located at vertices, as shown in Figure 20-13.
If you do not align the two vertices when you sketch the cylinder, you risk generating a distorted mesh.
For example, the vertices of the two concentric circles are not aligned in Figure 20-14.
7-635
The Mesh module
As a result, the mesh is slightly distorted on the right side, as shown in Figure 20-15.
· ``What kinds of elements must be generated outside the Mesh module?,'' Section 20.5.2
7-636
The Mesh module
Most elements in ABAQUS/Standard and ABAQUS/Explicit correspond to one of the shapes shown;
that is, they are topologically equivalent to these shapes. For example, although the elements CPE4,
CAX4R, and S4R are used for stress analysis, DC2D4 is used for heat transfer analysis, and AC2D4 is
used for acoustic analysis, all five elements are topologically equivalent to a linear quadrilateral.
Every mesh region has one or more ABAQUS element types assigned to it by default. Each element
type corresponds to an element shape that can be used in the region. For example, a solid mesh region
typically has a hexahedral, a wedge, and a tetrahedral element type assigned to it by default. You can
change the element assignment to any ABAQUS element that is topologically equivalent to the
element shape assigned to the region.
However, since no element type checking is done until you submit the analysis, it is possible to choose
an element that is inappropriate for the analysis you will be conducting. For example, ABAQUS/CAE
7-637
The Mesh module
does not prevent you from specifying heat transfer elements such as DC2D4, even though you may be
conducting a stress analysis.
If you want to assign these element types to a model, you must use a text editor to add them to the
input file generated in the Job module. For information on generating the input file, see ``Basic steps
for analyzing a model,'' Section 21.2.1.
· A region selected from geometry-based part instances. The instances must have come from parts
you created in the Part module or from ACIS-, IGES-, or VDA-FS-format parts you imported.
· A set that refers to a region selected from geometry-based part instances. The set can also refer to a
skin reinforcement.
· An element or an element set from an orphan mesh part instance. (Gaskets are an exception: you
can apply gasket element types only to geometry-based part instances and not to orphan meshes.)
All regions from geometry-based part instances and all elements from an orphan mesh part instance
have default element type assignments. These assignments depend on the kind of part to which the
region or element belongs. You can view and change the ABAQUS element types that are assigned
using the Element Type dialog box, which you can display by selecting Mesh->Element Type. For
example, the Element Type dialog box for a two-dimensional region is shown in Figure 20-17.
Figure 20-17 The Element Type dialog box for a two-dimensional region.
7-638
The Mesh module
At the top of the dialog box, you enter your preferences for element library, geometric order, and
family. Then, you select a specific element type by clicking the tabs in the bottom half of the dialog
box and choosing from the options that appear. The dialog box can contain from one to three tabs
depending on the dimensionality of the selected region or regions:
· The Line tab allows you to assign one-dimensional element types to one-dimensional mesh
elements in the region.
· The Quad and Tri tabs allow you to assign two-dimensional element types to two-dimensional
mesh elements in the region.
· The Hex, Wedge, and Tet tabs allow you to assign three-dimensional element types to the
three-dimensional mesh elements in the region.
For example, in Figure 20-17 the options for a linear shell element from the ABAQUS/Standard
element library are selected. After clicking the Quad tab, reduced integration and finite membrane
strains are selected. The name and a brief description of the quadrilateral shell element that meets all of
these criteria appear at the bottom of the tabbed page.
The Tri tab in this dialog box is shown in Figure 20-18.
7-639
The Mesh module
The name and a brief description of the triangular shell element that meets all of the criteria specified
in the dialog box appear at the bottom of the Tri tabbed page in Figure 20-18. If the selected region in
this example happens to contain a combination of triangular and quadrilateral mesh elements:
· The quadrilateral mesh elements are assigned the S4R element type.
If the region contains only quadrilateral elements, all of the elements are assigned the S4R element
type.
For detailed, step-by-step instructions for assigning element types to a mesh region, see ``Associating
ABAQUS elements with mesh regions,'' Section 20.16.9.
· The region must be geometry-based. You cannot assign gasket elements to an orphan mesh region.
· If the region is a shell or a solid, you must assign the swept meshing technique to the region. If the
shell or solid region is not meshable using the swept meshing technique, you cannot assign gasket
elements to that region. The swept meshing technique ensures that the elements are structured in a
manner suitable for gasket modeling.
In addition, you should verify that the gasket elements are aligned correctly for regions where the
gasket axis has more than one possible orientation. When you mesh shell or solid regions, the axis of
each gasket element is coincident with the sweep path direction; therefore, you can control gasket
element alignment by specifying an appropriate sweep path.
For example, the part instance shown in Figure 20-19 has three possible sweep paths, and each path
has two possible sweep directions. If you mesh this part instance using gasket elements, you can
choose from six possible gasket axis orientations.
Figure 20-19 You must choose a sweep path and direction that provides an appropriate gasket axis
orientation for your model.
7-640
The Mesh module
the set, you must select the selection filter tool that appears in the prompt area; and then select
Skins from the list of objects to filter. The skin filter is available only when you are creating a set.
After you create the set that refers to the skin, you can then assign an element type to the named set.
Select the named set by clicking the Sets button from the right side of the prompt area.
· ``How are seeds and other attributes affected by partitioning?, '' Section 20.6.2
See Chapter 43, "The Partition toolset," for detailed information on how to use each tool in the
Partition toolset.
· To divide a complex, three-dimensional part instance into simpler regions that ABAQUS/CAE
can mesh using primarily hexahedral elements with the structured or swept meshing techniques.
7-641
The Mesh module
(Almost all three-dimensional part instances are meshable using the free meshing technique, but
three-dimensional free meshes can include only tetrahedral elements.)
By default, the free meshing technique with quadrilateral elements is applied to all two-dimensional
part instances. When you create the mesh using this default technique, ABAQUS/CAE implicitly
creates partitions that divide the part instance into regions that can be meshed using the structured
meshing technique. (For more information, see ``Free meshing with quadrilateral elements,'' Section
20.9.2.) Therefore, all two-dimensional parts are meshable without any manual partitioning.
However, when a three-dimensional part instance is unmeshable using hexahedral elements, you must
take one of the following steps:
· Change the element shape assigned to the part instance from hexahedra to tetrahedra so that the
free meshing technique can be applied to the part instance.
ABAQUS/CAE uses the color orange to indicate that a three-dimensional region is unmeshable using
hexahedral elements, as shown in Figure 20-20.
With the addition of a partition, the model can be meshed with hexahedral elements, as shown in
Figure 20-21; the green region can be meshed using the structured meshing technique, and the yellow
regions can be meshed using the swept meshing technique.
7-642
The Mesh module
Even when a part instance can be meshed without partitioning, you may still want to partition to gain
more control over mesh generation. Without partitions, the mesh is aligned only along the exterior
edges of the part instance; with partitions, the resulting mesh will have rows or grids of elements
aligned along the partitions. That is, the mesh "flows" along the partitions. For example, in Figure
20-22 the partition that divides the rectangle in two causes the mesh to flow at an angle along the
partition.
When partitioning, remember that partitions will become element boundaries. Therefore, try to ensure
that partitions make angles as close to 90° as possible with other partitions or edges.
Figure 20-23 The left and right edges each have seven elements.
7-643
The Mesh module
If you create a partition that splits the part instance into two regions, new vertices are created at the
midpoints of both edges. In Figure 20-24 you can see how ABAQUS/CAE added seeds at the new
vertices so that nodes will exist at the corners of each region. ABAQUS/CAE also redistributed the
existing seeds to eliminate any overly small elements created by the new partition. However, this
redistribution can result in seeds that are not aligned. The top region has one seed more on the left side
than it does on the right, and the reverse is true for the bottom region.
In this example you could change the number of elements along the right and left edges to an even
number to ensure that the seeds align after partitioning.
Any other mesh attributes, such as element shape or element type, that you have applied to the
assembly are applied automatically to each new region that you create when you partition the
assembly. However, once you have created the different regions, you can assign different mesh
attributes to each region.
7-644
The Mesh module
If you return to the Part module and widen the right side of the model, the partition also expands and
continues to divide the face into two regions, as shown in Figure 20-26.
Sometimes regeneration of a partition creates unmeshable regions. In this situation simply add, modify,
or delete partitions until the part instance becomes meshable again.
· ``Do I have to mesh the entire model in one operation?, '' Section 20.7.7
· ``Can I change the geometric order of the elements in a mesh?,'' Section 20.7.8
20.7.1 Overview
ABAQUS/CAE follows these basic steps to generate a mesh on a part instance or on a set of regions:
7-645
The Mesh module
1. Generate a mesh on each region using the meshing technique currently assigned to that region. By
default, ABAQUS/CAE generates meshes with first-order line, quadrilateral, or hexahedral
elements throughout.
2. Merge the meshes of all regions into a single mesh. (For more information, see ``Meshing multiple
three-dimensional solid regions,'' Section 20.11.1.)
Typically, ABAQUS/CAE merges the nodes along the common boundaries of neighboring regions into
a single set of nodes. However, in certain cases ABAQUS/CAE creates tied surface interactions
instead of merging these nodes; for example, along the common interface between hexahedral and
tetrahedral meshes.
Meshes generated by ABAQUS/CAE conform to the geometry of the part instance they discretize, as
shown in Figure 20-27:
Figure 20-27 The mesh conforms to the geometry of the part instance.
· Nodes that are on the boundary of the mesh (including the midside nodes of second-order
elements) are also on the boundary of the geometry.
· Midside nodes of second-order elements that are internal to the part instance are centered between
the two corner nodes.
For detailed, step-by-step instructions on creating a mesh, see ``Creating a mesh,'' Section 20.15.1.
7-646
The Mesh module
When you create a part in the Part module, it exists in its own coordinate system, independent of other
parts in the model. In contrast, when you create an instance of the part in the Assembly module and
position it relative to other part instances, you are working in the assembly's global coordinate system.
To preserve precision, the Mesh module separates the positioning information of a part instance from
the geometry of the instance. As a result, when you generate a mesh, the nodal coordinates for the part
instance are computed relative to the coordinate system of the original part. (When the Job module
generates an input file, ABAQUS/CAE writes the nodal coordinates for each instance relative to its
own coordinate system and passes the instance positioning and orientation information to the solver
via the *SYSTEM keyword.)
The Mesh module stores these nodal coordinates in single precision. If the geometry of the part lies far
from the origin of its coordinate system, some precision of the nodal coordinates will be lost. To
prevent this loss of precision, you should try to position a part close to the origin of its coordinate
system. For example, the origin of the coordinate system of an ABAQUS/CAE native part is located at
the origin of the sketch that defined the base feature. Therefore, if possible, you should position the
sketch of the base feature over the origin of the sketcher grid.
· Unmeshable: orange
(See ``Structured meshing,'' Section 20.8; ``Free meshing,'' Section 20.9; and ``Swept meshing,''
Section 20.10, for information about each meshing technique.)
In many cases ABAQUS/CAE can use more than one technique to mesh a region; in these cases you
can either accept the default technique, or you can use the Mesh Controls dialog box to select an
alternative technique. In addition, you can change which meshing techniques are valid for a region by
adding partitions to the region or by assigning a different element shape to the region. For example, if
you change the element shape assignment of an unmeshable three-dimensional part instance from
hexahedra to tetrahedra, the part instance becomes meshable using the free-meshing technique. For
more information, see ``Why partition?,'' Section 20.6.1.
For detailed information on controlling the mesh technique and element shape assigned to a region, see
the following sections:
7-647
The Mesh module
ABAQUS/CAE provides mesh transition controls for the following types of meshes:
· A two-dimensional mesh that is created using the free or structured meshing technique.
By default, the transition control is set to allow mesh transition. In certain cases, changing the
transition control to a minimum level of mesh transition will reduce mesh distortion. However, the
mesh may deviate further from the specified mesh seeds.
When transition controls are applicable to the type of mesh you are creating, an Algorithm Options
field appears on the right side of the Mesh Controls dialog box. This field contains a toggle button
that allows you to select the level of mesh transition. (To display the Mesh Controls dialog box, select
Mesh->Controls from the main menu bar.) For more information, see ``Setting transition options,''
Section 20.16.5.
7-648
The Mesh module
Symmetric meshes.
You cannot ensure that ABAQUS/CAE will mesh a symmetric part instance with a symmetric
mesh.
· Seeding
· Element shape
· Meshing technique
· Transition control (For more information, see ``Setting transition options,'' Section 20.16.5.)
If you change any of the attributes listed, the existing mesh on the part instance or region will no
longer be consistent with its attributes. As a result, ABAQUS/CAE deletes the mesh and regenerates a
new mesh that matches the new attributes. (Element order and type are the only attributes that, when
changed, do not require the mesh to be deleted and regenerated.)
Whenever you make a change that will affect any of these attributes, ABAQUS/CAE displays a dialog
box similar to the one shown in Figure 20-29.
You can delete the mesh by clicking the Delete Meshes button, or you can keep your mesh and exit
the procedure by pressing the Cancel button.
You can also avoid this warning message for the remainder of the current session by toggling
7-649
The Mesh module
Automatically delete meshes whenever required . The next time you attempt to change the
attributes of a part instance or region that already contains a mesh, the mesh will be deleted
immediately without any warning being displayed.
Warning: There is no way to avoid deleting the mesh when you change one of the attributes listed
above. Since regeneration of a deleted mesh can be time consuming for large or complex models,
you should use caution when changing these attributes.
If you save your model to a model database before you delete the mesh, you can revert back to that
mesh if you are dissatisfied with later meshing attempts.
For detailed, step-by-step instructions on deleting a mesh, see ``Deleting a mesh,'' Section 20.15.2.
· Incremental meshing cannot proceed if the seeding between the existing mesh and the selected
region cannot be honored. You must allow ABAQUS/CAE to delete the existing mesh and remesh
the original regions and the selected region.
For example, consider the part instance in Figure 20-30.
7-650
The Mesh module
The central region cannot be meshed incrementally because one end has a mesh with 4 ´ 4 mesh
pattern and the opposite end has a mesh with a 3 ´ 3 mesh pattern. If you try to mesh only the
central region, ABAQUS/CAE will detect the problem and allow you to choose between the
following:
- Remesh the regions that are already meshed and the central region to generate a compatible
mesh.
· Incremental meshing cannot proceed if the existing mesh needs to be derived from the mesh you
are trying to create. For example, consider the part instance in Figure 20-31.
To create a compatible mesh between region 1 and region 2, the mesh of region 2 is derived from
the mesh of the cylinder in region 1. Similarly, the mesh of region 3 is derived from the mesh of
region 2, which in turn was derived from the mesh of the cylinder in region 1. As a consequence, if
you mesh region 3 first, ABAQUS/CAE cannot incrementally mesh regions 1 and 2. You must
allow ABAQUS/CAE to mesh region 1 prior to remeshing regions that were already meshed.
If incremental meshing cannot proceed, ABAQUS/CAE displays a warning message prior to deleting
an existing mesh.
If you want to mesh the assembly incrementally, you can follow a strategy that will minimize the
number of times ABAQUS/CAE has to delete the entire mesh. Changes to the seeding always
propagate out to the boundaries. As a result, you should start meshing from the interior of the assembly
and work out to its boundaries. The strategy depends on the modeling space of the assembly, the
element shape, and the meshing technique.
7-651
The Mesh module
Two-dimensional assembly
You should mesh the regions of a two-dimensional assembly in the following order:
2. Regions with more than five sides that can be meshed using the structured method.
3. Four-sided regions that use the structured method. Four-sided regions with mesh
transitions are the most forgiving.
Three-dimensional assembly
If you are creating a hexahedral mesh, you should mesh the regions of a three-dimensional
assembly in the following order:
Regions that are meshed by triangles or tetrahedral elements will never force the entire mesh to be
deleted during incremental meshing. ABAQUS/CAE can always remesh these regions, and you can
mesh them at any time.
If the part instance is an orphan mesh, you can change the order of all the elements in the part, or you
can change the order of only selected elements. An orphan mesh contains no underlying geometry
information, and as a result you should take care when changing the order of the elements. If you
change the elements in an orphan mesh from quadratic to linear, all information on the location of the
midside nodes is lost. As a result, if you subsequently decide to change back from linear to quadratic
elements, you will not be able to return to the original mesh.
7-652
The Mesh module
You can apply the structured meshing technique to regions that have been assigned the Quad or
Quad-dominated element shape option for simple two-dimensional regions (planar or curved) or the
Hex or Hex-dominated element shape option for simple three-dimensional regions. For more
information about assigning element shapes to a region, see ``Choosing an element shape,'' Section
20.16.2.
When you mesh a region using any meshing technique, the nodes on the boundary of the mesh are
always located on the boundary of the geometric region. However, when ABAQUS/CAE creates a
mesh using the structured meshing technique, it is possible for nodes in the interior of the mesh to fall
outside the region's geometry, which results in a distorted, invalid mesh. This problem typically occurs
near concave boundaries.
For example, the region in Figure 20-33 has five sides; therefore, when ABAQUS/CAE meshes this
region using the structured meshing technique, it applies the mesh pattern for a regular pentagon to the
region.
Figure 20-33 The mesh pattern for a regular pentagon is applied to the region.
7-653
The Mesh module
However, if you seed the region so that the number of elements is reduced, as shown in Figure 20-34, a
distorted mesh results due to the concavity at the highly curved edge. Nodes from the interior of the
mesh pattern (indicated by closed circles in Figure 20-35) fall outside the region's geometry, while
nodes on the boundary of the mesh (indicated by open circles in Figure 20-35) remain on the boundary
of the region's geometry.
Figure 20-35 Nodes from the interior of the mesh fall outside the region's geometry.
When interior nodes fall outside the region's geometry, you can try the following techniques to
improve the mesh:
· Change the mesh seeds and remesh. For example, the number of elements along the highly curved
edge in Figure 20-33 is greater than in Figure 20-35.
7-654
The Mesh module
· Partition the part instance into smaller, more regularly shaped regions. For example, the model was
partitioned into three regions in Figure 20-36.
· Select a different meshing technique. This option is most useful for two-dimensional regions,
where you can switch from structured meshing to free meshing and still retain quadrilateral
elements in the mesh. (Three-dimensional free meshing is limited to tetrahedral elements. For
more information, see ``Free meshing,'' Section 20.9.) Figure 20-37 shows the region meshed using
the free meshing technique.
Figure 20-37 Mesh the region using the free meshing technique.
The mesh in Figure 20-37 is not symmetric, which is typical of free meshes.
7-655
The Mesh module
· The region is bounded by three to five logical sides, where each side is a connected set of edges.
ABAQUS/CAE combines edges into a logical side automatically if the edges subtend a shallow angle.
For example, each region in Figure 20-38 has five edges. However, since the top two edges in each
region subtend a shallow angle, ABAQUS/CAE considers these two edges to be one logical side.
Therefore, the mesh pattern for four-sided regions is applied to these regions.
You can use the Redefine Region Corners button in the Mesh Controls dialog box to combine
edges yourself, regardless of the angle they subtend. (To display the Mesh Controls dialog box, select
Mesh->Controls from the main menu bar.) This technique allows you to control which structured
mesh pattern is applied to the two-dimensional region. (This technique is not available for
three-dimensional regions.) For more information, see ``Redefining region corners,'' Section 20.16.4.
Figure 20-39 Regions that can be meshed using the structured meshing technique.
7-656
The Mesh module
Meshing more complex regions with this technique may require manual partitioning. If you do not
partition a complex region, your only meshing option may be the free meshing technique with
tetrahedral elements. Meshes constructed using the structured meshing technique consist of hexahedral
elements, which are preferred over tetrahedral elements.
The characteristics described in the following list are required to successfully mesh a
three-dimensional region using the structured meshing technique:
· The region cannot have any holes, isolated faces, isolated edges, or isolated vertices.
You can eliminate holes (whether they pass all the way through the part instance or just part way
through) by partitioning their circumferences into halves, quarters, etc. For example, the four
partitions in the figure below convert the part instance from one region with a hole to four regions
without holes.
· You should limit arcs to 90° or less to avoid concavities along sides and at edges. For example, the
part instance in the figure below has been partitioned so that the single region with 180° arcs
becomes two regions with 90° arcs.
7-657
The Mesh module
· All the faces of the region must have geometries that could be meshed using the two-dimensional
structured meshing technique. For example, without partitioning, the semicircles at either end of
the model below have only two sides each. (A face must have at least three sides to be meshed
using the structured meshing technique.) If you partition the model in half, each semicircle is
divided into two faces with three sides each.
· Exactly three edges of the region must meet at each vertex. For example, the vertex at the top of an
unpartitioned pyramid is connected to four edges. However, if you partition the pyramid into two
tetrahedral regions, the vertex is connected to only three edges for each individual region.
· The region must be bounded by at least four sides (a tetrahedral region), up to a maximum of 15
sides. If a region is bounded by fewer than four sides, you can partition the region as necessary to
create additional sides.
· The angles between sides should be as close to 90° as possible; you should partition to eliminate
angles greater than 150°.
· Each side of the region must match one of the following definitions:
- If the region is not a cube, a side must correspond to a single face; that is, the side must not
contain multiple faces.
- If the region is a cube, a side can be a connected set of faces that are on the same geometric
surface. However, each face must have four sides. In addition, the pattern of the faces must
allow rows and columns of hexahedral elements to be created in a regular grid pattern along
that entire side when the cube is meshed. For example, the sides in the following figure have
acceptable face patterns:
If the cubes in the figure above are meshed using the structured meshing technique, a regular
grid pattern of elements is created in each mesh, with a consistent number of rows and
columns appearing on the partitioned sides, as shown below:
7-658
The Mesh module
The sides in the following figure do not have acceptable face patterns:
The face pattern shown on the left is unacceptable for structured meshing because each face
has only three sides. Each face in the pattern shown on the right has four sides, but the pattern
does not allow a regular grid of elements to be created on the partitioned side of the cube, as
shown below:
7-659
The Mesh module
are usually not symmetric, even if the part instance itself is symmetric.
The free meshing technique with quadrilateral elements can be applied to any planar surface. Similarly,
the free meshing technique with quadrilateral elements can be applied to curved surfaces; however, the
region's boundaries should not be close to a singular point of a surface. Typically, surfaces with
singular points are created when you revolve a profile that touches the axis of revolution or when you
create blends or fillets in certain cases. (Examples of singular points are the two poles of a sphere.)
If you use the free meshing technique to mesh a region and then remesh the region (for example, after
modifying the seeds), some of the steps for creating the mesh are not repeated, and the new mesh is
generated more quickly.
7-660
The Mesh module
Free meshing with tetrahedral elements can be applied to almost any three-dimensional region; in fact,
very complex models can be meshed using this technique without the help of partitioning. Figure
20-42 shows an example of a free tetrahedral mesh.
7-661
The Mesh module
· ABAQUS/CAE creates a mesh on one side of the region, known as the source side.
· ABAQUS/CAE copies the nodes of that mesh, one element layer at a time, until the final side,
known as the target side, is reached. ABAQUS/CAE can copy the mesh while following a straight
edge connecting the source and target sides; this is called an extruded swept mesh. Alternatively,
ABAQUS/CAE can copy the mesh while following a circular edge connecting the source and
target sides; this is called a revolved swept mesh.
For example, Figure 20-43 shows an extruded swept mesh. To mesh this model, ABAQUS/CAE first
creates a two-dimensional mesh on the source side of the model. Next, each of the nodes in the
two-dimensional mesh is copied along a straight edge to every layer until the target side is reached.
To determine if a region is swept meshable, ABAQUS/CAE tests if the region can be replicated by
sweeping a source side along a straight or circular edge to the target side. It is not possible for the user
to control which side is the source side and which is the target side. In general, ABAQUS/CAE selects
the most complex side (for example, the side that has an isolated edge or vertex) to be the source
side.
7-662
The Mesh module
(For more information on assigning element shapes to a region, see ``Choosing an element shape,''
Section 20.16.2.)
ABAQUS/CAE cannot generate a revolved surface mesh that touches the axis of revolution at two
points unless the revolved surface is a sphere.
Figure 20-45 The extruded swept meshing technique sweeps the mesh on the source side along a
straight edge.
If the source side can be swept along a circular edge, ABAQUS/CAE creates a revolved swept mesh.
7-663
The Mesh module
Figure 20-46 illustrates how ABAQUS/CAE meshes the source side and revolves that mesh about the
axis of the circular edge to the target side.
Figure 20-46 The revolved swept meshing technique sweeps the mesh on the source side along a
circular edge.
ABAQUS/CAE can generate swept meshes on regions that have been assigned either the Hex or the
Hex-dominated element shape option. If you apply the Hex element shape option to the region,
ABAQUS/CAE uses the two-dimensional free meshing technique with the Quad element shape option
to generate the preliminary two-dimensional mesh on the source side. If you apply the Hex-dominated
element shape option to the region, ABAQUS/CAE uses the two-dimensional free meshing technique
with the Quad-dominated element shape option to generate the mesh on the source side; as a result,
the final three-dimensional mesh may contain columns of wedge elements.
The following limitations apply to three-dimensional swept meshing:
· Every side that connects the source side to the target side must contain only a single face without
isolated edges or isolated vertices. For example, the model in Figure 20-47 cannot be meshed
using the swept meshing technique because one of the connecting sides is partitioned into two
faces.
· The target side must contain only a single face without isolated edges or isolated vertices. For
example, the region on the left in Figure 20-48 can be meshed using the swept meshing technique
because all of the isolated edges are on the source side; the region on the right, however, cannot be
meshed using this technique because the target side contains two faces.
7-664
The Mesh module
Figure 20-48 Only the region on the left can be meshed using the swept meshing technique.
· For a revolved region, the profile that was revolved to create the region must not touch the axis of
revolution unless both the top and the bottom of the region are planar. If the top and the bottom of
the region are planar, you can use partitions to render the region meshable using the swept
meshing technique. For more information, see ``Sweep meshing a solid, revolved region whose
profile touches the axis of revolution, '' Section 20.16.7.
· ``Meshing multiple two- and three-dimensional shell regions, '' Section 20.11.2
Figure 20-49 A compatible mesh is impossible using these default meshing techniques.
7-665
The Mesh module
The mismatch that would occur between the nodes of the structured region and the nodes of the swept
region is obvious if you mesh the two regions separately, as shown in Figure 20-50.
Figure 20-50 The structured region and the swept region meshed separately.
If you initiate the meshing procedure and ABAQUS/CAE cannot generate a compatible mesh using the
default meshing techniques, ABAQUS/CAE attempts to replace the default meshing techniques with
new meshing techniques. These new techniques are determined not only by the region's geometry and
topology but also by the characteristics of neighboring regions in the part instance. ABAQUS/CAE
evaluates the interfaces between regions and tries to minimize the number of incompatible interfaces.
For example, the default meshing technique for the cube on the left side of the part instance in Figure
20-49 is structured. However, this cube can also be meshed using the swept meshing technique.
Therefore, ABAQUS/CAE changes the meshing technique assigned to this region from structured to
swept, and a compatible mesh is generated over the whole part instance. (The element types assigned
7-666
The Mesh module
to a region remain unchanged when ABAQUS/CAE changes the meshing technique assigned to the
region.)
When you initiate the meshing procedure for a three-dimensional part instance, ABAQUS/CAE
determines if a compatible mesh can be generated using the default techniques assigned to each region
in the part instance. If a compatible mesh is possible, meshing proceeds. If a compatible mesh cannot
be generated using the default techniques, ABAQUS/CAE checks to see if it can replace the default
meshing techniques with different techniques that will allow a compatible mesh to be generated.
· If different techniques will allow a compatible mesh, ABAQUS/CAE highlights the incompatible
interfaces and prompts you to select one of the following options:
- Allow ABAQUS/CAE to use the default meshing techniques and automatically generate tied
surface interactions across the incompatible interfaces. ABAQUS/CAE generates common
(merged) nodes on the perimeter of the incompatible interface and a tied surface interaction
between the interior surface nodes. The interior surface nodes of the two regions form a
contact pair, where each of the nodes on the slave surface are constrained to have the same
value of displacement, temperature, pore pressure, or electrical potential as the point on the
master surface that they contact. ABAQUS/CAE generally selects the surface with the higher
mesh refinement to be the slave surface. The computation for the depth of the adjustment zone
is based on the bounding dimensions of the interfacing regions. (For more information on tied
surfaces, see ``Defining tied contact,'' Section 21.2.4 of the ABAQUS/Standard User's Manual
and Section 20.2.4 of the ABAQUS/Explicit User's Manual. For more information on the
adjustment zone, see ``Adjusting initial surface positions and specifying initial clearances in
contact pairs,'' Section 21.2.2 of the ABAQUS/Standard User's Manual and Section 20.2.2 of
the ABAQUS/Explicit User's Manual.)
· If different techniques will still not allow a compatible mesh, ABAQUS/CAE highlights the
incompatible interfaces and prompts you to select one of the following options:
If a compatible mesh cannot be generated, you can try one of the following approaches:
· Use the free meshing technique to mesh the entire part instance.
7-667
The Mesh module
· A swept region cannot share its target side with a structured region. However, it can share a source
side or a connecting side with a structured region, as shown in Figure 20-51.
Figure 20-51 The connecting side of the swept region is shared with the structured region.
· A part instance cannot contain regions of hexahedral elements as well as regions of tetrahedral
elements.
· In some situations ABAQUS/CAE cannot mesh a part instance that contains multiple regions that
have all been assigned the swept meshing technique. For example, ABAQUS/CAE cannot sweep a
mesh along the part instance shown in Figure 20-52 because a compatible mesh cannot be
generated on the shared target face.
Figure 20-52 A swept mesh cannot be generated along this part instance.
7-668
The Mesh module
7-669
The Mesh module
7-670
The Mesh module
You can return to the Part module and modify the hole at the center of the model so that it is slightly
larger. When you return to the Mesh module, the partitions and the seeds are regenerated, as shown in
Figure 20-56.
In addition, settings in the Mesh Controls and Element Type dialog boxes (such as element shape,
element type, and meshing technique) are also regenerated. (You can display these two dialog boxes by
selecting Mesh->Controls and Mesh->Element Type from the main menu bar.)
Note: If you drastically modify the part, the seeds and partitions may fail to regenerate. In these
cases you must create new seeds and partitions after reentering the Mesh module.
7-671
The Mesh module
For information on using each of the Mesh module tools, refer to the following sections:
As you work through the tutorial, you will perform the following procedures:
· ``Assigning element shapes to the model and specifying a meshing technique,'' Section 20.13.4
7-672
The Mesh module
3. Click the File type arrow, and select Model Database (*.cae) if it is not already selected.
4. In the Selection field at the bottom of the Open Database dialog box, delete the default text and
type the path of the file containing the model database.
5. Click OK.
ABAQUS/CAE reads the model database containing the clamp model.
· Whether the region is meshable using the element shape currently assigned to the region.
· If the region is meshable, which default meshing technique ABAQUS/CAE will use to mesh the
region.
In this tutorial the entire model turns orange when it first appears in the Mesh module, indicating that
the part instance is currently unmeshable using the hexahedral element shapes that are assigned to the
model by default. You will make the part meshable with hexahedral elements by partitioning the clamp
into smaller regions.
To partition the model:
7-673
The Mesh module
The cursor changes to an hourglass while the Mesh module loads. The clamp model appears in the
viewport, as shown in Figure 20-59.
Note: During the course of this tutorial, you can use the following techniques to manipulate the orientation of the clamp in the
viewport:
· Use a combination of the view manipulation tools and the display option tools in the toolbar and the tools in the Views
toolbox to resize and reposition the model as necessary. (The Views toolbox appears when you select from the
toolbar.)
In particular, you will probably find the magnification tool and the rotation tool useful for displaying the
model at a convenient size and orientation.
· When necessary, click the Iso tool in the Views toolbox to return the model to its original size and position in
the viewport.
The view orientation triad in the lower left corner of the screen indicates the orientation of the model with respect to the view.
The triad in the middle of the model indicates the origin and orientation of the global coordinate system. For more information
on the view manipulation tools, see Chapter 8, "Manipulating the view and controlling perspective."
3. In the dialog box, select Cell from the list of Type options and select Extend face from the list of
Method options. Then click Apply.
4. In the viewport, select the clamp model, and click Done in the prompt area.
5. In the viewport, select the bottom face of the top part of the clamp, as shown in Figure 20-60.
7-674
The Mesh module
Use the selection options (accessible from the prompt area) to filter your selection so that you can
choose from all entities. If your selection is ambiguous, click Next or Previous in the prompt area
until ABAQUS/CAE selects the desired face. Click OK to confirm your choice.
As a result of the new partition the top region of the clamp turns green, indicating that the region
can be meshed using the structured meshing technique.
7. Use a similar method to create a partition using the upper face of the bottom part of the clamp, as
shown in Figure 20-62.
7-675
The Mesh module
Both the top and the bottom regions of the clamp are now green, which indicates that both are
meshable with a structured mesh pattern. The middle region of the clamp is now yellow, which
indicates that it is swept-meshable.
8. In the Create Partition dialog box, click Cancel to close the dialog box.
2. In the toolbar, use the zoom tool , the magnification tool , and the pan tool to
enlarge the model in the viewport.
3. Use the [Shift]+Click technique to select all of the edges of the middle region of the clamp, as
shown in Figure 20-63. When you have finished selecting edges, click mouse button 2. (To learn
how to use the [Shift]+Click technique to select all of the edges, see ``Selecting and unselecting
individual objects,'' Section 9.2.1.)
7-676
The Mesh module
4. In the text field in the prompt area, enter an approximate element size of 2 and then click
Constraints on the right side of the prompt area.
The Edge Seed Constraints dialog box appears. The options in this dialog box allow you to
control how closely ABAQUS/CAE adheres to the seeds on the selected edges when creating the
mesh.
5. In the dialog box, click Allow the number of elements to increase only and then click OK.
This selection prevents ABAQUS/CAE from reducing the number of elements that appear along
the selected edges. In other words, ABAQUS/CAE can either create the same number of elements
as is specified by the seeds or, if necessary, create more elements than are specified by the seeds.
6. Click mouse button 2 to save your seeding specifications for the middle region of the model.
The edge seeds that you have created appear in magenta along the edges of the middle region of
the clamp. Their shapes have the following significance:
· The triangular seeds are partially constrained; ABAQUS/CAE can only increase their number,
not decrease it, during mesh generation.
· The square seeds are fully constrained and cannot be altered by the mesh generation process.
Fully constrained seeds always appear at vertices.
8. In the text field in the prompt area, enter an approximate element size of 3 for the remaining edges
in the model and then click mouse button 2.
Instance seeds appear in white along the edges of the model that have not yet been seeded. (The
edges that you have already seeded individually retain their magenta seeds.) The instance seeds are
circular, which indicates that they are unconstrained; if necessary, ABAQUS/CAE will change
their number and location to generate the mesh.
7-677
The Mesh module
9. Use the auto-fit tool to return the model to its original size in the viewport.
The Hex option is selected by default; if you do not change the Element Shape option, your mesh will
contain only hexagonal-shaped elements automatically.
Note: If you had changed the element shape option to Tet at the beginning of the tutorial,
ABAQUS/CAE would have been able to mesh the model without any partitions using the free
meshing technique. To achieve a given accuracy, meshes composed of tetrahedral elements
generally require more elements than hexahedral meshes and, therefore, are more expensive to
analyze. As a result, the mesh generator does not use these types of elements unless you
specifically request them.
2. Select the top and the bottom regions of the model, as shown in Figure 20-64, and then click
mouse button 2.
7-678
The Mesh module
3. In the dialog box, accept the default element shape selection of Hex.
6. Use a similar method to view and accept the default selections for the middle region of the model.
7. In the prompt area, click Done to exit the mesh controls assignment procedure.
3. Once the mesh is complete, click the shaded render style tool in the tool bar. The model
should appear as shown in Figure 20-65.
7-679
The Mesh module
5. From the main menu bar, select Mesh->Delete Instance Mesh. A prompt in the prompt area asks
whether to delete the mesh; click Yes.
The mesh is deleted.
7. In the Create Partition dialog box, select Cell from the list of Type options and select Extend
face from the list of Method options. Then click Apply.
In the prompt area, you are prompted to select the cells to partition.
8. In the viewport, select the top and bottom regions of the clamp model, and click Done in the
prompt area.
7-680
The Mesh module
Use the selection options (accessible from the prompt area) to filter your selection so that you can
choose from all entities. If the selection is ambiguous, click Next or Previous in the prompt area
until ABAQUS/CAE selects the desired face. Click OK to confirm your choice.
11. Remesh the model. (It is unnecessary to seed the new partitions; they will be seeded
automatically.) The new mesh should appear as shown in Figure 20-68.
7-681
The Mesh module
The partitions that you have added significantly reduce the distortion of the elements toward the
left end of the clamp.
12. In the Create Partition dialog box, click Cancel to close the dialog box.
2. Drag a rectangle around the clamp to select the entire model. Then click mouse button 2.
The Element Type dialog box appears.
4. Accept the default Element Library, Geometric Order, and Family selections.
In the bottom half of the dialog box the Hex tab is visible. The name and a brief description of a
default hexagonal, three-dimensional stress ABAQUS/Standard element type appears at the
bottom of the tabbed page.
5. Accept the default element type selection. Then, click the Wedge and Tet tabs to view the wedge
element and tetrahedral element options. If your mesh contained any wedge- or tetrahedral-shaped
elements, the default ABAQUS element types that appear at the bottom of the Wedge and Tet
tabbed pages would be assigned to those elements.
6. Click OK to accept the default settings and to close the dialog box.
· You can use the Partition toolset to partition an unmeshable model into smaller, meshable regions.
7-682
The Mesh module
· The density of a mesh is determined by the number and type of the seeds that you create along the
edges of the region.
· The Mesh Controls dialog box allows you to assign an element shape and a meshing technique to
a region. The Element Type dialog box allows you to assign ABAQUS/Standard or
ABAQUS/Explicit element types to the mesh elements in a region.
· ``Defining seed density for the entire part instance,'' Section 20.14.1
· ``Relaxing constraints using the error dialog box, '' Section 20.14.9
Tip: You can also seed a part instance using the tool, located with the seed tools in the
Mesh module toolbox. (For more information, see ``Using the Mesh module toolbox,'' Section
20.12.)
7-683
The Mesh module
2. If your assembly contains more than one part instance, select the part instance to seed and click
mouse button 2.
Note: Edge seeds always override instance seeds; therefore, if you have already individually
seeded all the edges of the part instance, the instance seeds are unused and do not appear on
the part instance. If necessary, use the seed deletion tool, described in ``Deleting edge seeds,''
Section 20.14.8, to remove any unwanted edge seeds; if you have assigned instance seeds to
the part instance, instance seeds automatically appear on the edges where you delete edge
seeds.
3. In the text field in the prompt area, type an approximate element size.
4. If desired, change the default seed constraints by clicking the Constraints button in the prompt
area and responding to the dialog box that appears. See ``Applying constraints to seeds,'' Section
20.14.5, for further information on setting seed constraints.
5. Press [Enter] or click mouse button 2 to commit the element size and constraint settings.
White seeds appear on all edges of the part instance except those already assigned magenta edge
seeds.
6. To change the selected seed size or constraints, repeat this procedure from Step 3.
7. To exit the instance seeding procedure, press [Enter] or click mouse button 2.
7-684
The Mesh module
Tip: You can also seed an edge by number of elements using the tool, located with the
seed tools in the Mesh module toolbox. (For more information, see ``Using the Mesh module
toolbox,'' Section 20.12.)
2. Select the edges you want to seed. When you are finished selecting edges, press mouse button 2.
For more information on selecting objects, see Chapter 9, "Selecting objects within the viewport."
3. In the text field in the prompt area, type the number of elements to be used along the selected
edges.
4. If desired, change the default seed constraints by clicking the Constraints button in the prompt
area and responding to the dialog box that appears. See ``Applying constraints to seeds,'' Section
20.14.5, for further information on setting seed constraints.
5. Press [Enter] or mouse button 2 to commit the element size and constraint settings.
Magenta edge seeds appear along the selected edges.
7. To exit the edge seeding procedure, press [Enter] or click mouse button 2.
7-685
The Mesh module
the main menu bar. All the edge seeding tools generate edge seeds, which are displayed in magenta.
Edge seeds override any part seeds you have specified.
You need not seed all edges of a region. If only some edges of the region have edge seeds (and you
have not created any instance seeds), ABAQUS/CAE can interpolate the element density requirements
for the unseeded edges from those of the seeded edges.
Detailed instructions for seeding an edge by prescribing the element size:
Tip: You can also seed an edge by element size using the tool, located with the seed
tools in the Mesh module toolbox. (For more information, see ``Using the Mesh module
toolbox,'' Section 20.12.)
2. Select the edges you want to seed. When you are finished selecting edges, press mouse button 2.
For more information on selecting objects, see Chapter 9, "Selecting objects within the viewport."
3. In the text field in the prompt area, type the approximate element size to be used along the selected
edges.
4. If desired, change the default seed constraints by clicking the Constraints button in the prompt
area and responding to the dialog box that appears. See ``Applying constraints to seeds,'' Section
20.14.5, for further information on setting seed constraints.
5. Press [Enter] or mouse button 2 to commit the element size and constraint settings.
Magenta edge seeds appear along the selected edges.
7. To exit the edge seeding procedure, press [Enter] or click mouse button 2.
7-686
The Mesh module
All the edge seeding tools generate edge seeds, which are displayed in magenta. Edge seeds override
any part seeds you have specified.
Detailed instructions for prescribing biased seeding along an edge:
Tip: You can also click the tool, located with the seed tools in the Mesh module
toolbox. (For more information, see ``Using the Mesh module toolbox,'' Section 20.12.)
2. Select the edges you want to seed. As you select each edge, click near the end where you want the
mesh to be denser.
For more information on selecting objects, see Chapter 9, "Selecting objects within the viewport."
4. In the text box in the prompt area, type the bias ratio to be used along the selected edges. The bias
ratio must be greater than or equal to one and less than or equal to 1.0E6.
6. In the text field in the prompt area, type the desired number of elements to be created along the
selected edges.
7-687
The Mesh module
7. If desired, change the default seed constraints by clicking the Constraints button in the prompt
area and responding to the dialog box that appears. See ``Applying constraints to seeds,'' Section
20.14.5, for further information on setting seed constraints.
8. Press [Enter] or mouse button 2 to accept the element number and constraint settings.
Magenta seeds appear on the selected edges of the part instance.
10. To exit the edge seeding procedure, press [Enter] or click mouse button 2.
1. From the main menu bar, select Seed->Instance or Seed->edge seeding option of your
choice. Then select the part or the edges you want to seed and click mouse button 2. For more
information on performing these tasks, see the following sections:
· ``Defining seed density for the entire part instance,'' Section 20.14.1
7-688
The Mesh module
ABAQUS/CAE displays prompts in the prompt area to guide you through the procedure.
This option leaves the seeds totally unconstrained. Therefore, the number of elements that
ABAQUS/CAE creates along an edge can be greater or smaller than the number of
elements dictated by the seeds; however, the mesh generator tries to adhere to the
requested seed pattern as much as possible.
This option is the default. It provides the greatest flexibility to the automatic mesh
generator and, therefore, gives the greatest chance of success when generating the mesh.
Allow the number of elements to increase only
This option partially constrains the seeds so that the number of elements along an edge or
throughout a part instance can only be greater or remain the same as that dictated by the
seeds. It is sometimes helpful to know that unconstrained seeds that are located near
partially constrained seeds also tend to behave as though they are partially constrained.
Do not allow the number of elements to change
This option fully constrains the seeds so that the exact number of elements that you have
specified with your seeds is maintained. You can use this option only with edge seeds;
instance seeds cannot be fully constrained.
Use this option with care, since adjustment of the number of elements along the boundary
of a region is usually required to generate a mesh; preventing such adjustments can make
mesh generation impossible.
Note: The constraint options described above allow you to control only the number of elements along an edge, not the
positions of the nodes along the edge. ABAQUS/CAE creates meshes that adhere to the seeds as closely as possible, but the
locations of the seeds and the locations of the nodes along the mesh edges usually do not match exactly.
4. Click OK.
The mesh seeds change shape to indicate the constraint you have chosen:
· Triangle: partially constrained seed. The triangle points upward, indicating that the number of
elements along the edge can only increase.
7-689
The Mesh module
· Before seeding, use the mesh deletion tools, described in ``Deleting a mesh,'' Section 20.15.2, to
delete the mesh from the part instance or region of interest.
· Do not delete the mesh yourself; instead, attempt to seed the part instance or region of interest. As
soon as you select the parts or edges to seed, ABAQUS/CAE displays a window similar to the
following:
You can delete the mesh by clicking Delete Meshes, or you can keep your mesh and exit the
seeding procedure by pressing Cancel.
You can avoid this warning message for the remainder of the current session by toggling on
Automatically delete meshes whenever required . The next time you attempt to seed a part
instance or region that already contains a mesh, the mesh will be deleted immediately without any
warning being displayed.
7-690
The Mesh module
Tip: You can also delete seeds using the tool, located with the seed tools in the Mesh
module toolbox. (For more information, see ``Using the Mesh module toolbox,'' Section
20.12.)
· If your assembly contains only one part instance, click Yes in the prompt area to confirm the
deletion.
· If your assembly contains more than one part instance, select the instances whose seeds you
want to delete and click mouse button 2 to commit your selections.
The instance seeds disappear from the selected part instance or instances.
7-691
The Mesh module
Tip: You can also delete seeds using the tool, located with the seed tools in the Mesh
module toolbox. (For more information, see ``Using the Mesh module toolbox,'' Section
20.12.)
2. Select the edges whose edge seeds you want to delete and then click mouse button 2 to commit
your selections.
The seeds disappear from all selected edges.
Tip: To delete seeds from an entire region or part instance, drag-select all the desired edges.
For more information on selecting objects, see Chapter 9, "Selecting objects within the
viewport."
In addition, the overconstrained seeds are highlighted in the viewport. You can choose one of the
7-692
The Mesh module
following options:
· Click Yes to relax the seed constraints and to continue meshing the region.
· Click No to save the seed constraints and to cancel the meshing procedure.
Tip: You can also mesh part instances or regions using the and tools, located
with the mesh tools in the Mesh module toolbox. (For more information, see ``Using the Mesh
module toolbox,'' Section 20.12.)
7-693
The Mesh module
Select only those part instances or regions that are colored green, pink, or yellow,
indicating they are meshable. To make orange regions meshable, you must either
subdivide them using the partitioning tools or assign tetrahedral-shaped elements to them.
1. From the main menu bar, select either Mesh->Delete Instance Mesh or Mesh->Delete Region
Mesh.
ABAQUS/CAE displays prompts in the prompt area to guide you through the procedure.
Tip: You can also delete meshes using the or tools, located with the mesh tools
in the Mesh module toolbox. (For more information, see ``Using the Mesh module toolbox,''
Section 20.12.)
7-694
The Mesh module
2. (For more information on selecting objects, see Chapter 9, "Selecting objects within the
viewport.")
ABAQUS/CAE deletes the mesh throughout the selected part instances or regions.
Tip: You can also click the tool, located in the Mesh module toolbox. (For more
information, see ``Using the Mesh module toolbox,'' Section 20.12.)
7-695
The Mesh module
2. If your assembly contains more than one region, select the regions whose mesh controls you want
to view or modify and then press mouse button 2. All the selected regions must have the same
dimensionality. (For more information on selecting objects, see Chapter 9, "Selecting objects
within the viewport.")
The Mesh Controls dialog box appears.
3. Select the mesh controls of your choice. For information on specific mesh controls, see the
following:
4. If desired, click Defaults to change the settings in the Mesh Controls dialog box back to the
default values. (Clicking Defaults has no effect on the transition options selected for a region or
on the corners currently defined for a region.)
5. Click OK to save your settings and to close the Mesh Controls dialog box.
Tip: You can set the element shape using the tool, located in the Mesh module
toolbox. (For more information, see ``Using the Mesh module toolbox,'' Section 20.12.)
7-696
The Mesh module
2. If your assembly contains more than one region, select those regions whose element shapes you
want to view or modify and then press mouse button 2. All the selected regions must have the
same dimensionality. (For more information on selecting objects, see Chapter 9, "Selecting objects
within the viewport.")
The Mesh Controls dialog box appears.
3. From the list of Element Shape options, select the element shape of your choice.
If you are meshing a two-dimensional region, you can choose from the following element shape
options:
Quad
Use exclusively quadrilateral elements; do not use any triangles. This setting is the
default. The following figure shows an example of a mesh that was constructed using this
setting:
Quad-dominated
Use primarily quadrilateral elements, but allow triangles in transition regions. The
following figure shows an example of a mesh that was constructed using this setting:
Tri
Use exclusively triangular elements. The following figure shows an example of a mesh
that was constructed using this setting:
7-697
The Mesh module
If you are meshing a three-dimensional region, you can choose from the following element shape
options:
Hex
Use exclusively hexahedral elements; do not use any triangular prisms (wedges). This
setting is the default. The following figure shows an example of a mesh that was
constructed using this setting:
Hex-dominated
Use primarily hexahedral elements, but allow some triangular prisms in transition regions.
The following figure shows an example of a mesh that was constructed using this setting:
7-698
The Mesh module
Tet
Use exclusively tetrahedral elements. The following figure shows an example of a mesh
that was constructed using this setting:
4. Click OK.
The next time you generate a mesh on the selected regions, your selections will be honored.
If the selected regions are already meshed, you will be prompted to delete the mesh or to cancel the
entire procedure.
7-699
The Mesh module
Tip: You can set the meshing technique using the tool, located in the Mesh module
toolbox. (For more information, see ``Using the Mesh module toolbox,'' Section 20.12.)
2. If your assembly contains more than one region, select those regions whose meshing technique you
want to view or modify and press mouse button 2. The selected regions must all have the same
dimensionality. (For more information on selecting objects, see Chapter 9, "Selecting objects
within the viewport.")
The Mesh Controls dialog box appears.
3. From the list of Technique options, select the meshing technique of your choice. (Some
techniques are available only if they are valid for the selected region.)
· ABAQUS/CAE selects As is if, in the previous step, you selected multiple regions that have
different meshing techniques already assigned to them.
For detailed information on each meshing technique, see ``Understanding mesh generation,''
Section 20.7.
4. Click OK to close the dialog box and to save your mesh technique selection.
The next time you generate a mesh on the selected part instance or region, your selections will be
7-700
The Mesh module
honored.
If the selected region already contains a mesh, you will be prompted to delete the mesh or to cancel
the entire procedure.
Tip: You can also click the tool, located in the Mesh module toolbox. (For more
information, see ``Using the Mesh module toolbox,'' Section 20.12.)
2. If your assembly contains more than one region, select those regions whose corners you want to
redefine and then press mouse button 2. (For more information on selecting objects, see Chapter 9,
"Selecting objects within the viewport.") The regions that you select should have three or more
vertices.
The Mesh Controls dialog box appears.
7-701
The Mesh module
· If you click Accept Highlighted, ABAQUS/CAE accepts the currently highlighted corners. If
multiple regions are selected, options are presented for the next region. If only one region is
selected, the procedure is complete, and the Mesh Controls dialog box reappears.
· If you click Select New , the currently selected vertices turn red. You must go on to the next
step.
· If you click Revert to Defaults, the default corners of the region are highlighted. You are
prompted to select either Accept Highlighted or Select New , described above.
6. If you clicked Select New in the previous step, select the vertices of the region that you want as
region corners. You can select between three and five vertices.
· [Ctrl]+Click to unselect an individual vertex without unselecting all the other vertices.
· A two-dimensional quadrilateral mesh that is created using the free meshing technique.
7-702
The Mesh module
If the mesh transition option is applicable to the type of mesh you are creating, an Algorithm Options
field appears on the right side of the Mesh Controls dialog box. This field contains a toggle button
that allows you to select the level of mesh transition.
Detailed instructions for setting transition options:
Tip: You can also click the tool, located in the Mesh module toolbox. (For more
information, see ``Using the Mesh module toolbox,'' Section 20.12.)
2. If your assembly contains more than one region, select the regions of interest and then press mouse
button 2. (For more information on selecting objects, see Chapter 9, "Selecting objects within the
viewport.")
The Mesh Controls dialog box appears. If the mesh transition option is applicable to the type of
mesh you are creating, an Algorithm Options field appears on the right side of the Mesh
Controls dialog box.
· Toggle on Use a minimum level of mesh transition to reduce the amount of mesh transition.
This selection helps ABAQUS/CAE to reduce the level of mesh distortion.
· Toggle off Use a minimum level of mesh transition to allow unrestricted generation of
mesh transitions. This selection helps ABAQUS/CAE to adhere more closely to the seeds you
have created when the mesh is generated.
7-703
The Mesh module
path, you can click Redefine sweep path to select the path of your choice. (For more information on
sweep paths, see ``Swept meshing,'' Section 20.10.)
This option is of particular interest if you are assigning mesh controls to a gasket region. When you
mesh the region, the axis of each gasket element will be coincident with the sweep path direction. (For
information on gaskets, see ``Gasket elements: overview,'' Section 18.1.1 of the ABAQUS/Standard
User's Manual.)
Detailed instructions for specifying the sweep path:
Tip: You can also click the tool, located in the Mesh module toolbox. (For more
information, see ``Using the Mesh module toolbox,'' Section 20.12.)
2. If your assembly contains more than one region, select the sweep-meshable regions of interest and
then press mouse button 2. (For more information on selecting objects, see Chapter 9, "Selecting
objects within the viewport.")
The Mesh Controls dialog box appears.
3. In the Mesh Controls dialog box, select Sweep as the meshing technique if it is not already
selected.
If more than one valid sweep path exists for the regions that you selected, a Redefine Sweep Path
button appears toward the bottom of the dialog box.
5. Specify the sweep path and direction of your choice by selecting the appropriate option in the
prompt area:
· Click Accept Highlighted to accept the default sweep path indicated in the viewport.
· Click Flip to change the direction of the currently selected sweep path. Then click Yes to
indicate that the new sweep path direction is correct.
· Click Select New (if applicable) to select a different edge as the sweep path. Then perform the
following steps:
1. Select an edge in the sweep path. You can indicate the desired sweep direction by clicking
the mouse button toward the end of the edge that you want to coincide with the end of the
sweep path.
7-704
The Mesh module
The new sweep path is highlighted in red with an arrow indicating the sweep direction.
2. Click Yes in the prompt area if the path and direction are correct, or click Flip if you want
to change the direction of the sweep path. Then click Yes to indicate that the new sweep
path direction is correct.
If multiple regions are selected with more than one valid sweep path, the procedure starts over
with the next region. If only one region is selected, the procedure is complete and the Mesh
Controls dialog box reappears.
The partitioning technique involves dividing the part instance into two regions:
· A cylindrical core region that can be meshed using the extruded swept meshing technique.
· An outer region that can be meshed using the revolved swept meshing technique.
(For detailed information on sweep meshing solid regions, see ``Swept meshing of three-dimensional
solids,'' Section 20.10.3.)
Detailed instructions for partitioning a solid, revolved region for sweep meshing:
1. Use the Partition toolset to create a cylidrical core at the center of the region. (For detailed
information on partitions, see Chapter 43, "The Partition toolset.") The partitions creating the
7-705
The Mesh module
The cylidrical core is meshable using the extruded swept meshing technique and therefore
becomes yellow. The outer region remains orange because it is still unmeshable.
In the next step you will create additional partitions that allow ABAQUS/CAE to recognize the
outer region as a revolved solid whose profile does not touch the axis of revolution.
2. Use the Partition toolset to create whatever partitions are necessary to outline a revolution profile
for the outer region. The profile will serve as the source side of the revolved mesh and will be
swept along the circular edge defined by the cylindrical core to create the solid mesh.
For example, partitions are used to outline the profile (shown in red) of the outer region in the
figure below.
7-706
The Mesh module
Once the profile has been defined, both the cylidrical inner region and the outer region are colored
yellow and are ready for sweep meshing.
7-707
The Mesh module
You can delete the mesh by clicking Delete Meshes, or you can keep your mesh and cancel the new
settings in the Mesh Controls dialog box by clicking Cancel.
You can also avoid this warning message for the remainder of the current session by toggling on
Automatically delete meshes whenever required . The next time you attempt to change the controls
assigned to a region that already contains a mesh, the mesh will be deleted immediately without the
appearance of the warning dialog box.
7-708
The Mesh module
Tip: You can also choose element types using the tool, located in the Mesh module
toolbox. (For more information, see ``Using the Mesh module toolbox,'' Section 20.12.)
2. If your assembly contains both orphan meshes and native part instances,
· click Mesh in the prompt area to assign an element type to an orphan mesh, or
· click Geometry in the prompt area to assign an element type to native geometry.
3. If you are selecting from multiple regions of native geometry or if you are selecting elements from
an orphan mesh, use the following selection techniques:
Native geometry
Use the mouse to select the desired regions in the viewport, and then click mouse button 2
when your selection is complete. For more information on selecting objects, see Chapter
9, "Selecting objects within the viewport."
You can select only regions from parts of the same type; for example, you cannot select
both a rigid surface and a deformable body. Likewise, the regions that you choose must
have the same dimensionality.
Orphan mesh
Use the mouse to select the desired elements of the orphan mesh, and then click mouse
button 2 when your selection is complete. For more information on selecting objects, see
Chapter 9, "Selecting objects within the viewport."
7-709
The Mesh module
Alternatively, you can click Sets on the right side of the prompt area. A dialog box
appears with a list of all of the elements sets associated with the orphan mesh. Select the
element set of your choice and then click Continue. For information on creating sets, see
Chapter 45, "The Set and Surface toolsets."
All elements that you select, regardless of the selection method, must be of the same
order. In addition, the elements must belong to parts of the same type.
4. In the upper left corner of the dialog box, select the Element Library option of your choice.
Select Standard to choose from the list of ABAQUS/Standard elements, or select Explicit to
choose from the list of ABAQUS/Explicit elements.
5. Select the Geometric Order of your choice: Linear (first order) or Quadratic (second order).
Note: If you are assigning an ABAQUS element type to orphan mesh elements, this option is unavailable. The order of orphan
mesh elements cannot be changed.
6. From the Family list on the right side of the dialog box, select an appropriate element family for
the type of analysis you will perform on the model. For example, if you plan to do a heat transfer
analysis, select the Heat Transfer family.
If you have not yet assigned ABAQUS element types to the region, the name of a default element
for the element library, geometric order, and family that you specified appears in the lower half of
the dialog box.
Note: You can set the element type corresponding to only a single family. For example, you
cannot set the element type for linear triangles in both the plane strain and heat transfer
families; you must select either heat transfer or plane strain. If, after setting element types for
one family, you switch to another family, the settings for the first family are lost.
7. Choose the ABAQUS element type of your choice for each element shape.
8. Click OK to commit your element type assignments, or click Defaults and then OK to return all
element settings to their default values.
The element types are changed according to your specifications.
9. To set element types for additional regions, repeat this procedure starting from Step 2.
7-710
The Mesh module
· ``What kinds of elements must be generated outside the Mesh module?,'' Section 20.5.2
Tip: You can also verify a mesh using the tool, located in the Mesh module toolbox.
(For more information, see ``Using the Mesh module toolbox,'' Section 20.12.)
2. If your assembly contains more than one part instance, select the part instances whose meshes you
want to verify and press mouse button 2. (For more information on selecting objects, see Chapter
9, "Selecting objects within the viewport.")
A dialog box containing the two options listed below appears. Each option causes a color-coded
plot to be generated that illustrates the following information:
This plot highlights all elements whose aspect ratios exceed the specified value. The
7-711
The Mesh module
aspect ratio is the ratio between the longer and shorter dimensions of an element. Aspect
ratios should remain below two or three. For example, the aspect ratio of the square below
is one, while the aspect ratio of the rectangle is four.
This plot highlights all elements whose angular deviation exceeds the specified value. The
angular deviation is the amount an element angle deviates from 90° for quadrilateral faces
or from 60° for triangular faces. For example, the angular deviation of the angle in the
triangle below is 30°, and the angular deviation of the angle in the quadrilateral is 50°.
3. From the dialog box, choose one of the verification options. Type any required values in the fields
that become available.
4. Click Plot.
ABAQUS/CAE displays a plot in the current viewport depicting the requested information. In
addition, the following information appears in the message area:
Part ID
A number that ABAQUS/CAE assigns to the part instance.
Average distortion
The average value for the verification option that you selected in the Verify Mesh dialog
box. For example, if you selected Whose aspect ratio exceeds: value, the average
aspect ratio for all of the elements in the mesh is given.
Worst distortion
The worst value for the verification option that you selected in the Verify Mesh dialog
box. For example, if you selected Whose aspect ratio exceeds: value, the highest aspect
ratio of all of the mesh elements is given.
7-712
The Mesh module
5. Click Cancel to dismiss the Verify Mesh dialog box and to remove the mesh verification plot
from the viewport.
· An instance mesh
· A region mesh
If the assembly contains multiple meshed regions, use the following techniques to specify the region
you want to query:
Tip: You can also select the query tool in the toolbar.
7-713
The Mesh module
2. From the Query dialog box, select one of the following mesh queries and click Apply:
Point
Select a point or a node.
ABAQUS/CAE displays the following in the message area:
Instance mesh
Tip: To enlarge the message area so that you can view the entire listing at once, drag
the small square at the upper right corner of the message area upward.
Element
Select an element.
ABAQUS/CAE displays the following in the message area:
· The element type that ABAQUS/CAE will use for the analysis
· Nodal connectivity
Region mesh
Select a region.
ABAQUS/CAE displays the following in the message area:
7-714
The Mesh module
· The element type that ABAQUS/CAE will use for the analysis
· The mesh algorithm and any options that were used to mesh the region
7-715
The Job module
· Start the Visualization module and view a basic plot of the analysis results.
8-716
The Job module
8-717
The Job module
· Create an analysis job and associate the new job with a selected model.
You can display the Job Manager by selecting Job->Manager from the main menu bar. Figure 21-1
shows the layout of the Job Manager.
8-718
The Job module
Name
The Name column displays the name of the job. Click Rename to rename the selected job.
Model
The Model column displays the name of the model associated with the job.
Type
The Type column displays the job type that you selected when you configured the job using
the job editor. The job type can be one of the following:
· Full Analysis
· Data Check
· Continue Analysis
· Recover
(See ``Selecting a job type,'' Section 21.2.5, for more information.) You can use the job editor
to change the job type as long as the job is not running.
Status
The Status column displays the current status of the analysis job and is updated continually
while your job is running. The status can be one of the following:
None
The job has not been submitted for analysis.
Submitted
The input file has been written, and the job is being submitted for execution.
Running
The job has been submitted for analysis and is running.
Completed
The analysis is complete. You can click Results to view the contents of the output
8-719
The Job module
Aborted
The job has been aborted due to problems such as fatal errors in the input file or lack
of disk space.
Terminated
The job has been killed by the user.
For detailed instructions on using the Job Manager to create, edit, and manipulate jobs, see the
following sections:
Submission
Use the Submission tabbed page to configure the submission attributes of your job, such as
job type, run mode, and submit time. You can also use the submission tabbed page to specify
that the job is to be submitted to remote queues that have been configured by your local
ABAQUS environment file or by your system administrator.
General
Use the General tabbed page to configure job settings such as the solver input file processor
printout and the name of the directory used for scratch files.
8-720
The Job module
Hardware
Use the Hardware tabbed page to configure the hardware settings that ABAQUS uses when
analyzing your job, such as memory utilization and parallel processing resources.
Solver
Use the Solver tabbed page to specify either single or double precision for ABAQUS/Explicit
analyses.
For detailed instructions on using the job editor to define jobs, see the following sections:
Generate (or regenerate) the input file, perform a complete analysis of your model, and write
the results to the output database. This option is the default.
Data check
Check that the model is consistent and complete by running the input file through the solver
input file processor. This option generates (or regenerates) the input file for the job. To check
the outcome, review the data ( .dat) file in your working directory.
Continue analysis
When ABAQUS performs a data check analysis, it creates and saves all the files necessary to
8-721
The Job module
continue the analysis. You can then submit the job with the Continue analysis option
selected to complete the analysis.
Recover (Explicit)
This option is available only when you are running ABAQUS/Explicit. Submit a job with this
option selected to complete your analysis after ABAQUS/Explicit stopped unexpectedly; for
example, after filling a disk or after a network problem.
For detailed instructions on choosing a job type, see ``Choosing the job type,'' Section 21.4.3.
The top half of the dialog box displays the information available in the status ( .sta) file that
8-722
The Job module
ABAQUS creates for the analysis. The bottom half of the dialog box displays the following
information:
· Click the Log tab to display the start and end times for the analysis that appear in the log ( .log)
file.
· Click the Errors and Warnings tabs to display the first ten errors or the first ten warnings that
appear in the data ( .dat), message (.msg), and, for ABAQUS/Explicit analyses, status ( .sta)
files. If a particular region of the model is causing the error or warning, a node or element set will
be created automatically that contains that region. The name of the node or element set appears
with the error or warning message, and you can view the set using display groups in the
Visualization module. (For more information on display groups, see Chapter 36, "Displaying a
subset of your model.")
· Click the Output tab to display a record of each output data entry as it is written to the output
database. In addition, if you requested that ABAQUS monitor the values of a degree of freedom of
a particular node to the message and status files, the Output tabbed page records each time this
information is written and the value of the degree of freedom at that point of the analysis. (For
more information, see ``Understanding output requests,'' Section 17.4, and ``Degree of freedom
monitor requests,'' Section 17.5.3.)
For detailed information on the different output files that ABAQUS creates during an analysis, see
``Output,'' Section 4.1.1 of the ABAQUS/Standard User's Manual and the ABAQUS/Explicit User's
Manual.
The information presented in the job monitor dialog box is updated continually as the analysis
progresses. If the job fails, the Errors tabbed page appears in front of the other tabbed pages
automatically to help you determine the cause of the failure.
If you requested DOF Monitor output on a particular degree of freedom for a particular node,
ABAQUS/CAE provides another opportunity to monitor the job by plotting the values of the degree of
freedom over time. The plot appears in a new viewport that is generated automatically when you
submit the job. If the visible part of the canvas is already filled with one or more viewports, the new
viewport may be placed on a part of the canvas that is not visible; in this case you should use the
scrollbars or enlarge the canvas to bring the viewport into view. (For information on requesting output
for a particular degree of freedom for a particular node, see ``Degree of freedom monitor requests,''
Section 17.5.3.)
If necessary, you can terminate the analysis job by clicking Kill in the lower left corner of the job
monitor dialog box.
8-723
The Job module
def makeQueues(*args):
session.Queue(name,
queueName,
hostName,
copyFiles,
directory,
driver,
localMachineType,
remoteMachineType,
filesToCopyBack,
comment)
addImportCallback('job', makeQueues)
This entry is written using the ABAQUS command language. The following list describes each
argument in the entry above.
name
The queue name that you want to appear in the Job editor.
queueName
The name of an existing queue on the host computer. (For information on creating queues on
the host computer, refer to the ABAQUS Site Guide.)
hostName
The name of the host computer. The default is the name of the local computer.
8-724
The Job module
copyFiles
When the analysis is complete, the value of this argument determines whether or not the
analysis files will be copied back to the directory from which the job was submitted. If the
hostName is different from the name of the local computer, the default is YES; if the hostName
is the same as the name of the local computer, the default is NO.
directory
The name of the directory on the host computer where you want the job run. You must have
write privileges to this directory. The default is the local directory (the directory from which
you are submitting the job).
driver
The name of the command on the host computer to execute ABAQUS/Standard or
ABAQUS/Explicit. The default is abaqus.
localMachineType
The platform on the local computer. You can specify either UNIX or NT (for Windows NT);
UNIX is the default.
remoteMachineType
The platform on the host computer. You can specify either UNIX or NT (for Windows NT);
UNIX is the default.
filesToCopyBack
The three-letter extensions of the analysis files that you want copied back to the local directory
when the job is complete. By default, the files with the following extensions are copied: log,
dat, msg, sta, odb, res, abq, and pac.
Note: The restart (.res) file, the ABAQUS/Explicit state (.abq) file, and the packaging
(.pac) file are platform-dependent; if your localMachineType and remoteMachineType
settings differ, you will not be able to copy and use these files without some kind of
translation. All of the other files listed above can be copied across platforms without any
difficulty.
comment
A short description of the queue.
The name and queueName arguments must be included in each queue definition. However, if you do
not include any of the other arguments in a queue definition, default values will be supplied
automatically. An example queue definition is shown below:
def cae_startup():
import os
from abaqus import *
8-725
The Job module
def makeQueues(*args):
session.Queue(name='long',
queueName='aba_long',
hostName='jobserver',
directory='/scratch/' + os.environ['USER'])
addImportCallback('job', makeQueues)
The commands in the example above configure the following:
name
The queue name displayed in the job editor is long.
queueName
The queue name on the host computer is aba_long.
hostName
The name of the host computer is jobserver.
directory
The directory on the host computer where ABAQUS will store the input file and all other files
associated with the job is /scratch/your user name.
def makeQueues(*args):
session.Queue(name='long',
queueName='aba_long',
hostName='jobserver',
directory='/scratch/' + os.environ['USER'])
session.Queue(name='job',
queueName='aba_job',
hostName='jobserver',
copyFiles=NO)
addImportCallback('job', makeQueues)
8-726
The Job module
The monitoring functions described in ``Monitoring the progress of an analysis job,'' Section 21.2.6,
are available for jobs run remotely just as they are for jobs run locally. However, the output database
for the job, like any other analysis files that you may have requested, is not copied to your local
directory until after the job is complete; therefore, you cannot use the Visualization module to view
results generated by an analysis in progress.
· ``Using the ABAQUS environment settings,'' Section 3.4.1 of the ABAQUS/Standard User's
Manual and the ABAQUS/Explicit User's Manual
Tip: You can also create a new analysis job by clicking the icon in the module toolbox
or by clicking Create in the Job Manager.
2. Type the name of the new job in the Name text field. The name that you specify must adhere to the
file name rules of your operating system.
3. The Model list displays all the models defined in the model database. From this list, select the
model to associate with the new job.
8-727
The Job module
4. Click Continue.
The job editor appears.
5. In the editor, enter all data necessary to define the job and click OK. (For more information, see
``Using the job editor,'' Section 21.4.)
8-728
The Job module
· In the Job Manager, select the job name and then click Kill.
· In the job monitor dialog box for that particular job, click Kill. (For more information, see
``Monitoring the progress of an analysis job,'' Section 21.2.6.)
ABAQUS/CAE asks you for confirmation, terminates the job, and updates the status of the job in the
Job Manager to Terminated.
8-729
The Job module
The Visualization module starts and presents you with a plot of the model.
Note: Using the Results command exits the Job module. To reenter the Job module, select Job from the Module list located
under the toolbar.
2. Use the Visualization module to create and customize different plots of your results. For more
information on using the Visualization module, see Part V, "Viewing results."
Use the Submission tabbed page to configure the basic attributes of your job, such as the job
8-730
The Job module
type, the run mode, and the run time. You can also use the submission page to submit jobs to a
remote queue.
General
Use the General tabbed page to configure preprocessor printout and to specify a scratch
directory and a user subroutine file.
Hardware
Use the Hardware tabbed page to configure the hardware settings that ABAQUS uses when
analyzing your job, such as memory utilization and parallel processing resources.
Solver
Use the Solver tabbed page to choose the solver that ABAQUS/Standard will use during the
analysis. You can also specify single or double precision for ABAQUS/Explicit analyses.
You can also use the ABAQUS environment file ( abaqus_v6.env) to control the default value of
many of the settings in the job editor tabbed pages. For more information, see ``Using the ABAQUS
environment settings,'' Section 3.4.1 of the ABAQUS/Standard User's Manual and the
ABAQUS/Explicit User's Manual.
8-731
The Job module
· Choose the type of analysis. (For more information, see ``Choosing the job type,'' Section 21.4.3.)
· Choose the run mode. (For more information, see ``Choosing the run mode,'' Section 21.4.4.)
· Choose the submit time. (For more information, see ``Setting the submit time,'' Section 21.4.5.)
Submit a job with this option selected to perform a complete analysis of your model and to
write the results to the output database. This option is the default.
Data check
Submit a job with this option selected to check that the model is consistent and that all the
required model options have been set. To see the results of a data check analysis, review the
data (.dat) file in your working directory. You can also view the results of a data check
analysis by selecting Job->Monitor->job of your choice to display the job monitor dialog
box. (For more information, see ``Monitoring the progress of an analysis job,'' Section 21.2.6.)
8-732
The Job module
Continue analysis
When you run an analysis with the Data check option above, ABAQUS creates and saves all
the files necessary to continue the analysis at a later time. Submit a job with the Continue
analysis option selected to complete the analysis.
Recover (Explicit)
This option is available only for ABAQUS/Explicit analyses. Submit a job with this option
selected to complete your analysis if ABAQUS/Explicit stopped unexpectedly; for example,
after running out of disk space or after a network problem.
The Job Type settings are analogous to parameters of the ABAQUS execution procecure; for more
information see ``Execution procedure for ABAQUS/Standard and ABAQUS/Explicit,'' Section 3.2.1
of the ABAQUS/Standard User's Manual and the ABAQUS/Explicit User's Manual.
Detailed instructions for choosing the job type:
1. In the job editor, click the Submission tab to display the Submission tabbed page.
2. From the Job Type options at the top of the tabbed page, select the job type of your choice.
· Queue, to submit your job to a named local or remote batch queue; select the batch queue from
the pull-down list. (You must define the queue in the ABAQUS environment file. For more
information, see ``Submitting a job remotely,'' Section 21.2.7.)
The Run Mode setting is analogous to parameters of the ABAQUS execution procecure. You can also
use the ABAQUS environment file ( abaqus_v6.env) to control the default run mode and to
customize the available queues. (See ``Submitting a job remotely,'' Section 21.2.7, for more
information.)
Detailed instructions for choosing the run mode:
1. In the job editor, click the Submission tab to display the Submission tabbed page.
8-733
The Job module
2. From the Run Mode options in the middle of the page, select either Background or Queue.
· ``Using the ABAQUS environment settings,'' Section 3.4.1 of the ABAQUS/Standard User's
Manual and the ABAQUS/Explicit User's Manual
1. In the job editor, click the Submission tab to display the Submission tabbed page.
2. From the Submit Time options at the bottom of the page, choose one of the following options:
Immediately
The job executes in the background of your local machine immediately or is submitted to
the batch queue immediately.
Wait
The job executes in the background of your local machine after a waiting period. Type the
waiting period in the hours and minutes fields. (This option is available only on UNIX
platforms. In addition, it is not available if the job is being submitted to a batch queue.)
At
The job executes at a time that you specify. Click Tip to the right of the At field for
information on what syntax to use when specifying a time. (This option is available only
on UNIX platforms.)
8-734
The Job module
The Preprocessor Printout options allow you to control whether ABAQUS prints an echo of
the input data, contact constraints, model definition data, and history data to the data ( .dat)
file. By default, each of these options is toggled on. The preprocessor printout options are
equivalent to the parameters of the *PREPRINT keyword.
Scratch directory
The Scratch directory option allows you to specify the name of the directory used for scratch
files. On UNIX systems the default scratch directory is the value of the $TMPDIR
environment variable or /tmp if the variable is not defined. On Windows NT systems the
default scratch directory is the value of the TEMP environment variable or \TEMP if the
variable is not defined. To specify a scratch directory, you can do one of the following:
· Click in the Scratch directory text field, and type the directory path.
· Click Select to display the Select Scratch Directory dialog box, and select the directory
of your choice.
Provide the name of the file containing all user subroutines that are referred to by the model.
To specify a user subroutine file, you can do one of the following:
· Click in the User subroutine file text field, and type the file path.
· Click Select to display the Select User Subroutine File dialog box, and select the file of
your choice.
If your model refers to a user subroutine, but you do not specify the name of the subroutine file
in the General tabbed page, ABAQUS generates an error that is reported by the job monitor
dialog box. (You can display the job monitor dialog box by selecting Job->Monitor->job of
your choice from the main menu bar.) For more information on subroutines, see Part
VIII"User Subroutines and Utilities," of the ABAQUS/Standard User's Manual and "User
Subroutines," Part VIII of the ABAQUS/Explicit User's Manual."
You can use the ABAQUS environment file ( abaqus_v6.env) to control the default value of most
of the settings in the General tabbed page; for more information, see ``Using the ABAQUS
environment settings,'' Section 3.4.1 of the ABAQUS/Standard User's Manual and the
8-735
The Job module
· The number of megabytes of memory allocated by the solver input file preprocessor.
· The number of megabytes used for each internal scratch buffer in the preprocessor.
· The maximum number of megabytes used for internal scratch buffer memory by
ABAQUS/Standard.
Settings within the Hardware tabbed page are equivalent to parameters of the job submission
command. For more information, see ``Execution procedure for ABAQUS/Standard and
ABAQUS/Explicit,'' Section 3.2.1 of the ABAQUS/Standard User's Manual.
Note: The memory-size settings of the job submission command are read by the solver as the
number of 64-bit words, not megabytes. Eight megabytes are equivalent to one million 64-bit
words.
You can use the ABAQUS environment file ( abaqus_v6.env) to control the default value of the
settings in the Hardware tabbed page; for more information, see ``Using the ABAQUS environment
settings,'' Section 3.4.1 of the ABAQUS/Standard User's Manual and the ABAQUS/Explicit User's
Manual.
8-736
The Job module
Use the Solver tabbed page to select either the single or double precision version of
ABAQUS/Explicit. This option is equivalent to the double option in the ABAQUS/Explicit
execution procedure. For more information, see ``Execution procedure for ABAQUS/Standard and
ABAQUS/Explicit,'' Section 3.2.1 of the ABAQUS/Explicit User's Manual.
8-737
The Sketch module
9-738
The Sketch module
the Done button that appears in the prompt area, and select any other module from the Module list.
You need not take any specific action to save your sketches before exiting the module; they are saved
automatically when you save the entire model by selecting File->Save or File->Save As from the main
menu bar.
You should recognize the difference between the Sketch module and the Sketcher. When you create or
edit a stand-alone sketch, the Sketch module starts the Sketcher and displays the Sketcher tools in the
module toolbox. In addition, ABAQUS/CAE starts the Sketcher whenever you do one of the
following:
· Sketch a partition on a face of the assembly while working in the Assembly module or the Mesh
module.
To exit the Sketcher and incorporate your sketch into the part or assembly, first exit the current
drawing tool by clicking mouse button 2. Then, click the Done button that appears in the prompt area.
Where applicable, follow any additional prompts to extrude, revolve, or sweep the feature.
ABAQUS/CAE exits the Sketcher and returns to the module that invoked it. In addition,
ABAQUS/CAE restores the original view of the part or assembly.
To create a stand-alone sketch, click the sketch create tool in the Sketch module toolbox.
When you are using the Sketcher (for example, when you are sketching the profile of a solid extrusion
in the Part module), you can save your work as a stand-alone sketch by clicking the sketch save tool
in the Sketcher toolbox. Similarly, you can incorporate one stand-alone sketch in another sketch
by clicking the sketch retrieve tool in the Sketcher toolbox. When you retrieve a stand-alone
sketch, ABAQUS/CAE does the following:
· Positions the retrieved sketch so that its origin is coincident with the origin of the current sketch.
9-739
The Sketch module
· Resizes the viewport so that both the current sketch and the retrieved sketch are displayed.
· Asks if you want to translate or rotate the retrieved sketch from the default position.
When you import a file as a stand-alone sketch, ABAQUS/CAE translates the contents of the file into a
set of Sketcher entities, such as lines, arcs, and splines. ABAQUS/CAE can import most planar entities
from an IGES-format file. For a complete list of the IGES entities that can be imported into a sketch,
see ``IGES entities recognized by ABAQUS/CAE when importing a part or a sketch,'' Section 13.5.5.
When you import an AutoCAD- or ACIS-format file, ABAQUS/CAE recognizes only the entities
listed in Table 22-1 and Table 22-2. If ABAQUS/CAE finds geometry that it cannot translate, it
ignores that geometry and continues importing the sketch.
9-740
The Sketch module
· ``Realigning the sketch grid relative to the sketch, '' Section 22.4.4
· ``How Sketcher customization options are initialized and saved, '' Section 22.4.6
9-741
The Sketch module
To see a tooltip containing a brief definition of a Sketcher tool, hold the mouse over the tool for a
moment. For information on using toolboxes and selecting hidden icons, see ``Using toolboxes that
contain hidden icons,'' Section 6.4.2.
The Sketcher tools allow you to do the following:
· Create basic sketch entities, such as lines, circles, arcs, fillets, and splines.
· Add construction geometry to your sketch to help you position and align sketch entities.
· Add dimensions to your sketch to make your sketch geometry more precise.
· If you are sketching the base feature of a new part, the sheet size is the same as the approximate
size of the part that you provided when you created the part. Similarly, if you are creating a
stand-alone sketch, the sheet size is the same as the approximate size of the sketch that you
provided when you created the sketch.
9-742
The Sketch module
· If you are adding a feature to a part or to the assembly, the sheet size is the same as the size used
by the most recent sketch of a feature belonging to the part or assembly. The sheet size does not
depend on the size of the face on which you are sketching.
You can use the Sketcher display options to increase or decrease the sheet size if it does not
correspond with the size of the geometry you are trying to sketch. To access the Sketcher display
options, select the customization tool from the Sketcher toolbox. You may need to use the
magnify tool to view the entire Sketcher sheet within the viewport.
ABAQUS/CAE overlays the sheet with a grid of invisible grid points to help you position the cursor as
you draw, move, resize, or reshape objects. By default, when you move the cursor near a grid point, the
cursor automatically moves, or snaps, to the point. This behavior relieves you from having to position
the cursor precisely, although it also prevents you from positioning the cursor between grid points. If it
is more convenient, you can disable the snapping behavior so that you have full control over the
cursor. To help you visualize the grid points underlying the Sketcher grid, ABAQUS/CAE displays
visible grid lines that pass through the grid points at a selected interval; for example, every other grid
point.
For example, Figure 22-2 shows a sheet whose size is set to 200 and a grid whose spacing is set to 10
units. Only one out of every two grid lines is visible; therefore, the spacing of the visible grid lines is
20 units. In addition, the Sketcher displays dashed lines along the grid indicating the X- and Y-axes of
the sketch; the lines intersect at the origin of the sketch.
9-743
The Sketch module
You can customize the appearance and behavior of the grid by choosing the spacing of grid points, the
spacing of the visible grid lines that overlay the grid points, and the sheet size. You can also realign the
grid relative to the sketch by moving the origin of the grid and by rotating the grid. Your sketch can
extend beyond the Sketcher grid; however, if you find that you need to sketch outside the grid, it is
recommended that you increase its size to include the entire sketch.
9-744
The Sketch module
ABAQUS/CAE starts the Sketcher and aligns the X- and Y-axes of the part with the axes of the
Sketcher grid, regardless of the type of feature you are creating. (ABAQUS/CAE derives the
X- and Y-axes of the part from the axes of the sketch that defined the base feature.)
1. Select the plane on which to sketch by selecting appropriate geometry; for example, a face
of a part or a datum plane.
2. If you are sketching the profile of an extruded or revolved feature, you must select the
direction of an arrow normal to the face. This arrow represents the direction in which the
sketch will be extruded or revolved.
3. Select an edge or datum axis that will appear vertical and on the right side of the Sketcher
grid. You can select any edge from the part or assembly that is not perpendicular to the
selected plane. You can select a datum axis, but you cannot select the edge of a datum
plane.
ABAQUS/CAE starts the Sketcher with the selected edge vertical and on the right side of the
grid. The vertical orientation of the view depends on the type of feature you are creating:
· When you are sketching a cut feature in the Part module, ABAQUS/CAE orients the view
so that the resulting feature will cut away from you and into the screen.
· When you are sketching a feature other than a cut (for example, an extrusion),
ABAQUS/CAE orients the view so that the resulting feature will protrude out of the
screen toward you.
If you are unsure of the part's or assembly's orientation relative to the sketch plane, use the
rotate tool to examine the sketch plane and the object on which you are sketching. Use the
9-745
The Sketch module
Note: ABAQUS/CAE does not consider the modeling space of the part or assembly when you
sketch a partition; you must always select the face to partition and the edge that will appear
vertical and on the right. However, for a three-dimensional part or assembly, you do not have to
select the direction of an arrow normal to the face; ABAQUS/CAE assumes that you are sketching
an extrusion protruding out of the selected face and orients the view accordingly.
· Shift the grid relative to the sketch by selecting a vertex representing the origin of the grid.
· Rotate the grid relative to the sketch by selecting a line that will be parallel to the X-axis of the
sketch.
· Remove any realignment and reset the grid to its original orientation.
Realignment applies only to the particular sketch, and the alignment of the grid is stored along with the
sketch in the model database. New and existing sketches retain their default alignment.
Even though you can rotate the sketch grid and change the coordinate system, the meaning of
horizontal and vertical does not change. Rotating the grid has the following effect:
· The coordinates of the current cursor position are displayed in the upper-left corner of the
9-746
The Sketch module
viewport, and you can use these coordinates as a guide. The coordinates displayed are relative to
the current alignment of the sketch grid and change if you realign the grid.
· When you enter the coordinates of a vertex in the prompt area, those coordinates are relative to the
current alignment of the sketch grid.
· Horizontal and vertical dimensions remain horizontal and vertical. Similarly, new dimensions
remain aligned with the horizontal and vertical axes.
· Old and new horizontal and vertical construction lines remain horizontal and vertical.
· The lines generated by the rectangle tool remain horizontal and vertical.
The primary cursor is the one you use with most applications on your computer, including
ABAQUS/CAE. The primary cursor usually appears as an arrow pointer or a pointing hand; you
position this cursor by moving the mouse. The secondary cursor is active only in the Sketcher; it
appears near the primary cursor only when the Sketcher prompts you to select a point. The position of
the secondary cursor allows you to see exactly which point is selected before committing the selection.
If you move the primary cursor near a point that is eligible for selection, the secondary cursor jumps
directly to the point while the primary cursor remains fixed. If you click the mouse button,
ABAQUS/CAE selects the point under the secondary cursor.
The appearance of the secondary cursor changes as you move around the sketch. This behavior is
called preselection. Table 22-3 shows the shape assumed by the secondary cursor when the primary
cursor is close to the Sketcher entity listed.
9-747
The Sketch module
· Vertices, midpoints, intersections, projections, and points of tangency highlight when you are
sketching a line, as shown in Table 22-3.
· Circle and arcs highlight when you are adding a radial dimension.
· Vertices and vertical lines highlight when you are adding a horizontal dimension.
· By default, the secondary cursor snaps to grid points. If you turn off this snapping, the secondary
cursor follows the primary cursor and can be positioned anywhere on the Sketcher sheet.
For more information on customizing the secondary cursor, see ``Turning snapping on or off,'' Section
22.8.2, and ``Turning preselection on or off,'' Section 22.8.3.
Sketcher options
· Snapping
9-748
The Sketch module
· Preselection behavior
Sketch options
Sketcher options control the interactive behavior of the Sketcher, while Sketch options control the
appearance of an individual sketch. ABAQUS/CAE stores and uses your Sketcher customization
settings only for the duration of the session. In contrast, ABAQUS/CAE stores your Sketch
customization settings along with each sketch in the model database; the settings apply only to the
particular sketch. As a result, if you exit the ABAQUS/CAE session and return to the sketch at a later
date, the customization options are retained.
9-749
The Sketch module
upon whether the feature defined by the reference geometry was created before or after the feature you
are editing.
If the reference geometry was created before the feature you are editing:
The Sketcher displays the reference geometry, and preselection symbols appear when you
move the cursor over it; for example, at vertices and midpoints.
If the reference geometry was created after the feature you are editing:
The reference geometry is visible, but you cannot select it for any sketching operation; in
addition, preselection symbols do not appear when you move the cursor over the reference
geometry.
If you have a choice, it is usually more convenient to edit the feature that was created most recently so
that you can take advantage of preselection with as much reference geometry as possible. You can use
the Query toolset to determine the order in which features were created; for more information, see
``Using the Query toolset to obtain feature information,'' Section 42.3.6.
When you sketch a new feature, you can constrain the position of the sketch to the underlying
reference geometry using one of the following methods:
· Select entities from the reference geometry while sketching the new feature; for example, select a
vertex to define the center of a circle or one end of a line.
· Create a linear dimension between the sketch and any reference geometry. For more information
on linear dimensions, see ``Specifying precise geometry,'' Section 22.6.
Constraining the sketch defines how it is positioned relative to the reference geometry and how it will
be repositioned if you modify the reference geometry.
When you exit the Sketcher, ABAQUS/CAE determines whether you have constrained the sketch to
the reference geometry. If a constraint is found, ABAQUS/CAE creates a parent-child relationship
between the new feature (the child) and the selected reference geometry (the parent). If no constraints
are found, ABAQUS/CAE displays the following message in the message area: No sketch
placement constraints specified on feature id N. You do not have to constrain
the sketch, but if you do not, its position relative to the reference geometry may change if you modify
the parent feature.
When you use the sketch save tool to save a stand-alone sketch, ABAQUS/CAE saves only the
sketch and does not save any underlying reference geometry. As a result, if the sketch includes a
dimension between a sketch line and a reference line, the dimension is not saved with the stand-alone
version of the sketch.
9-750
The Sketch module
the isolated point tool are considered construction geometry. Construction lines, circles, and
points do not appear in the feature you are creating or modifying.
While you are adding construction geometry and moving the cursor around the sketch, ABAQUS/CAE
displays preselection symbols at the following locations:
· The intersection of the new construction geometry and sketched lines or curves.
· The intersection of the new construction geometry and existing construction geometry.
· The intersection of the new construction geometry and reference geometry. ABAQUS/CAE
displays preselection symbols only when the reference geometry was created before the feature
being edited. (See ``Reference geometry,'' Section 22.5.1, for more information about the behavior
of reference geometry.)
The preselection symbols generated by construction geometry allow you to align objects precisely; for
example, along an oblique line or around a circle. For example, you could create an oblique
construction line and several vertical construction lines to help align a group of circles, as illustrated in
Figure 22-5.
Construction lines also define the axis of rotation when sketching revolved solids and surfaces. For
more information about the relationship between construction lines and the axis of revolution, see
``Defining the axis of revolution for axisymmetric parts and for revolved features, '' Section 14.9.2.
Construction geometry is shown using dashed magenta lines to distinguish it from sketched geometry.
9-751
The Sketch module
Construction geometry is visible only while you are working on a sketch; as soon as you exit the
Sketcher, the construction geometry disappears. ABAQUS/CAE saves construction geometry with the
original sketch; if the Sketcher is invoked to modify a sketch that included construction geometry, the
construction geometry reappears along with the sketch.
To create construction geometry, select one of the construction geometry tools from the Sketcher
toolbox or select Sketch->Construction from the main menu bar.
Figure 22-6, Figure 22-7, and Figure 22-8 illustrate how construction geometry and preselection
combine to help you create the desired sketch. In this example the user is creating a sketch of a
connecting rod.
1. Create two construction circles (indicated by dashed purple lines), as shown in Figure 22-6.
2. Sketch two fillets tangent to the construction circles (indicated by green lines), as shown in Figure
22-7.
3. Sketch two circular arcs (indicated by yellow lines); a preselection symbol indicates the vertices at
the ends of the fillets when you move the cursor close to them. The arcs are centered on the center
of the construction circles and extend between the vertices, as shown in Figure 22-8.
9-752
The Sketch module
Entering coordinates
When you are using the Sketcher to create a feature and ABAQUS/CAE asks you to position a
point (for example, to define the end point of a line or the center of a circle), you can do one of
the following:
· Select a point on the sketch using the Sketcher grid, existing vertices, or preselection.
· Enter the desired X- and Y-coordinates of the point in a text box in the prompt area.
To help you determine the coordinates to provide, the X- and Y-axes of the sketch are
indicated by dashed lines, which intersect at the origin of the sketch. The coordinates that
you specify are relative to this origin. In addition, when you select a Sketcher tool, the
coordinates of the current cursor position are displayed in the upper-left corner of the
viewport, and you can use these coordinates as a guide.
For detailed instructions, see ``Moving and resizing Sketcher objects by moving their
vertices,'' Section 22.12.1.
9-753
The Sketch module
dimensions. In addition, dimensions allow you to annotate sketches for future reference.
You add dimensions by selecting from the dimension tools in the Sketcher toolbox or by
selecting Sketch->Dimension from the main menu bar. To modify a dimension, select the
· ``Moving and resizing Sketcher objects by modifying their dimensions,'' Section 22.12.2
9-754
The Sketch module
If you choose to modify the dimension, you must decide whether that modification will affect vertex 1
or vertex 2. If you select vertex 1 to move, vertex 2 will remain fixed when the modification is made,
as shown in Figure 22-10.
The reverse is also true; if you select vertex 2 to move, vertex 1 will remain fixed, as shown in Figure
22-11. You can select multiple vertices to move when modifying a sketch. However, selecting both
vertex 1 and 2 to move would be an invalid choice in this example, since it would not be clear which
direction the two vertices should move; ABAQUS/CAE issues an error message in this case. You
could select both vertex 1 and 3 to move; the resulting sketch is shown in Figure 22-12.
9-755
The Sketch module
· Sketch geometry
· Reference geometry
· Construction geometry
9-756
The Sketch module
For example, consider a three-dimensional shell with an extruded circular post, as shown in the
following figure:
2. Extrude a solid feature from the face of the shell (the circular post).
In this example the user wants to keep the distance between the left edge of the shell and the center of
the post constant, regardless of how the shell is resized. To maintain this relationship, the user edits the
post and adds a dimension between the center of the sketched circle and the left edge of the reference
geometry that represents the shell, as shown in the following figure:
If the user moves either the left or the right edge of the shell, the distance between the center of the
circle and the left edge remains constant, as shown in the following figure:
9-757
The Sketch module
You can modify linear, angular, and radial dimensions. For detailed instructions, see ``Moving and
resizing Sketcher objects by modifying their dimensions,'' Section 22.12.2.
Translation
You can translate selected vertices by specifying the start and end coordinates of a translation
vector. The translation vector can start from any point; however, you may find it more
meaningful to start the vector from one of the selected vertices and end it at the vertex's new
location. Figure 22-13 shows the selected vertices, the translation vector, and the result of the
translation.
Rotation
You can rotate selected vertices by specifying the coordinates of the center of rotation and
9-758
The Sketch module
entering the angle of rotation; a positive angle indicates a counterclockwise rotation. Figure
22-14 shows the selected vertices, the selected center of rotation, and the result of a 90°
rotation.
Display the Sketcher customization options by clicking the options tool at the bottom of the
Sketcher toolbox. For more information, see ``How Sketcher customization options are initialized and
saved,'' Section 22.4.6.
9-759
The Sketch module
The following options control the behavior and appearance of only the current sketch and are stored
along with the sketch:
· The sheet size, the grid spacing, and the number of grid lines to display.
· The origin of the sketch grid and the alignment of the X-axis.
· The text height and the number of decimal places displayed in sketch dimensions.
1. From the bottom of the Sketcher toolbox, select the Sketcher customization tool .
The Sketcher Options dialog box appears.
2. Set the desired customization options. For detailed help on the items within the dialog box, request
context-sensitive help on the individual items.
3. Click OK to apply your changes and close the Sketcher Options dialog box.
· ``How Sketcher customization options are initialized and saved, '' Section 22.4.6
9-760
The Sketch module
1. From the bottom of the Sketcher toolbox, select the Sketcher customization tool .
The Sketcher Options dialog box appears.
3. After you have chosen the desired customization options, click OK to apply your changes and to
close the Sketcher Options dialog box.
1. From the bottom of the Sketcher toolbox, select the Sketcher customization tool .
The Sketcher Options dialog box appears.
9-761
The Sketch module
3. After you have chosen the desired customization options, click OK to apply your changes and to
close the Sketcher Options dialog box.
· ``How Sketcher customization options are initialized and saved, '' Section 22.4.6
The boundary of the sheet is always square, and its height and width are equal to the sheet
size. If you find that the sheet size is too large or too small, you can use the Sketcher Options
dialog box to change the size.
When you create a part, the Create Part dialog box asks you to define the approximate size of
the new part, and ABAQUS/CAE bases the default sheet size on the approximate size of the
part that you provide. The approximate part size must be between 10 5 and 10-3 units.
ABAQUS/CAE does not use specific units, but the units must be consistent throughout the
model.
Grid spacing
You can use this option to change the grid spacing using the same units that define the Sheet
size. If Snap to grid is enabled, the cursor will snap to each grid point.
The Sketcher grid helps you set the size and position of your sketch; by default, the grid is
visible when you start the Sketcher. The grid may become distracting if the geometry of your
sketch is complex, and you can use the Sketcher Options dialog box to remove the grid from
the sketch. If snapping is enabled, the cursor still snaps to the grid even if the grid is not
visible.
9-762
The Sketch module
Grid lines do not have to appear at every grid point. You can use the Sketcher Options dialog
box to define how many grid points are present between each grid line. If Show grid is
toggled off, the 1 out of n lines field is not available.
The following figure shows the relationship between the sheet size, the grid spacing, and grid lines:
Sheet size and grid customization options apply only to the current sketch and are stored along with
the sketch.
Detailed instructions for customizing the sheet size and grid:
1. From the bottom of the Sketcher toolbox, select the Sketcher customization tool .
The Sketcher Options dialog box appears.
2. In the text box next to Sheet size, type the dimension of the square sheet that will contain the
feature being created or edited.
Specify the sheet size in units consistent with those used to describe the rest of the model.
3. In the text box next to Grid spacing, type the desired spacing between grid points.
Specify spacing in the same units that you used to define the sheet size.
5. In the Show grid: 1 out of n lines text box, enter a number indicating how many grid lines should
be shown. For example, if you enter a value of two, ABAQUS/CAE displays a grid line over every
other grid point.
6. After you have chosen the desired customization options, click OK to apply your changes and to
9-763
The Sketch module
· ``How Sketcher customization options are initialized and saved, '' Section 22.4.6
· Shift the grid relative to the sketch by selecting a vertex representing the origin of the grid. To help
you locate the origin of the sketch, the X- and Y-axes of the sketch are indicated by dashed lines
that intersect at the origin.
· Rotate the grid relative to the sketch by selecting a line from the sketch that will be parallel to the
X-axis of the grid.
1. From the bottom of the Sketcher toolbox, select the customization tool .
The Sketcher Options dialog box appears.
2. From the buttons across the center of the dialog box, do the following:
· Click Origin to move the origin of the sketch grid relative to the part. Select the new origin
from the sketch or type the coordinates of the origin in the prompt area.
· Click Angle to rotate the sketch grid relative to the part. Select a line that will be parallel to
the X-axis of the sketch.
· Click Reset to restore the original sketch origin and to restore the original alignment of the
X-axis.
3. After you have chosen the desired customization options, click OK to apply your changes and to
close the Sketcher Options dialog box.
9-764
The Sketch module
· ``Realigning the sketch grid relative to the sketch, '' Section 22.4.4
· ``How Sketcher customization options are initialized and saved, '' Section 22.4.6
If you change the sheet size or zoom the view, the original text height of dimensions may no longer be
appropriate. You can change the text height by typing a new value in the Dimension text height field
of the Sketcher Options dialog box.
In addition, you may want to change the number of decimal places to match the dimensions of the
feature you are creating and the sheet size. You can use the Decimal places field to control the
number of decimal places displayed in each dimension. Dimension customization options apply only to
the sketch you are working on and are stored along with the sketch.
Detailed instructions for customizing the appearance of dimensions in the Sketcher:
1. From the bottom of the Sketcher toolbox, select the Sketcher customization tool .
The Sketcher Options dialog box appears.
2. Next to the Dimension text height label, type the desired height of the dimension text.
Specify the height in the same units you used to define the sheet size.
3. Next to the Decimal places label, click the arrows to increase or decrease the number of decimal
places that will be included in the dimension text.
The number of decimal places displayed can vary from zero to six.
4. After you have chosen the desired customization options, click OK to apply your changes and to
close the Sketcher Options dialog box.
9-765
The Sketch module
· ``How Sketcher customization options are initialized and saved, '' Section 22.4.6
If the construction geometry becomes distracting, you can use the Show construction geometry
option in the Sketcher Options dialog box to hide it. (By default, construction geometry is displayed
when you start the Sketcher.) If preselection is enabled, the cursor will still snap to items associated
with hidden construction geometry, such as the intersection of a line with a construction line.
Customization of the display of construction geometry applies only to the current sketch and is stored
along with the sketch.
Detailed instructions for displaying or hiding construction geometry:
1. From the bottom of the Sketcher toolbox, select the customization tool .
The Sketcher Options dialog box appears.
3. After you have chosen the desired customization options, click OK to apply your changes and to
close the Sketcher Options dialog box.
9-766
The Sketch module
· ``How Sketcher customization options are initialized and saved, '' Section 22.4.6
· ``Sketching arcs using a center point and two endpoints, '' Section 22.9.5
1. From the Sketcher toolbox, select the point tool . For a diagram of the tools in the
Sketcher toolbox, see ``The Sketcher tools,'' Section 22.4.1.
ABAQUS/CAE displays prompts in the prompt area to guide you through the procedure.
9-767
The Sketch module
You should take care positioning points while sketching because this positioning can affect the quality
of your mesh. Points in the sketch become vertices of the part you are creating or modifying. In turn,
when you mesh your model in the Mesh module, ABAQUS/CAE converts these vertices into fully
constrained seeds and places nodes at their location. For information on how to subsequently move
vertices, see ``Moving and resizing Sketcher objects by moving their vertices,'' Section 22.12.1.
Detailed instructions for sketching lines and polygons:
1. From the line tools in the Sketcher toolbox, select the connected lines tool . For a diagram
of the tools in the Sketcher toolbox, see ``The Sketcher tools,'' Section 22.4.1.
ABAQUS/CAE displays prompts in the prompt area to guide you through the procedure.
2. To construct a simple line, click the two end points. To construct a connected line or a polygon,
click each vertex.
Tip: If necessary, you can use the text box in the prompt area to enter the precise coordinates
of the vertices of the line. For more information on precisely defining the line, see ``Specifying
precise geometry,'' Section 22.6.
9-768
The Sketch module
The line or polygon appears as you click a vertex or enter the coordinates.
tool in the Sketcher toolbox to delete the most recent line segment. If you make a
mistake in an earlier segment, you can delete the incorrect segments using the Delete tool
4. To create more lines or polygons, repeat the above steps beginning with Step 2.
You should take care positioning points while sketching because this positioning can affect the quality
of your mesh. Points in the sketch become vertices of the part you are creating or modifying. In turn,
9-769
The Sketch module
when you mesh your model in the Mesh module, ABAQUS/CAE converts these vertices into fully
constrained seeds and places nodes at their location. For information on how to subsequently move
vertices, see ``Moving and resizing Sketcher objects by moving their vertices,'' Section 22.12.1. For
information on how to subsequently move vertices that define rectangles, see ``Moving and resizing
Sketcher objects by moving their vertices,'' Section 22.12.1.
Detailed instructions for sketching a rectangle:
1. From the line tools in the Sketcher toolbox, select the rectangle tool . For a diagram of the
tools in the Sketcher toolbox, see ``The Sketcher tools,'' Section 22.4.1.
ABAQUS/CAE displays prompts in the prompt area to guide you through the procedure.
2. Click the desired locations of any two opposite corners of the rectangle.
Tip: If necessary, you can use the text box in the prompt area to enter the precise coordinates
of the corners of the rectangle. For more information on precisely defining the rectangle, see
``Specifying precise geometry,'' Section 22.6.
The rectangle appears as you move the cursor or enter the coordinates.
9-770
The Sketch module
You should take care positioning points while sketching because this positioning can affect the quality
of your mesh. Points in the sketch become vertices of the part you are creating or modifying. In turn,
when you mesh your model in the Mesh module, ABAQUS/CAE converts these vertices into fully
constrained seeds and places nodes at their location. For information on how to subsequently move
vertices, see ``Moving and resizing Sketcher objects by moving their vertices,'' Section 22.12.1. For
information on how to subsequently move vertices that define circles, see ``Moving and resizing
Sketcher objects by moving their vertices,'' Section 22.12.1.
Detailed instructions for sketching a circle:
1. From the Sketcher toolbox, select the circle tool . For a diagram of the tools in the
Sketcher toolbox, see ``The Sketcher tools,'' Section 22.4.1.
ABAQUS/CAE displays prompts in the prompt area to guide you through the procedure.
The circle appears as you move the cursor. When you click the circumference, ABAQUS/CAE
draws the circle.
4. To create more circles, repeat the above steps beginning with Step 2.
9-771
The Sketch module
An arc that forms part of an analytical rigid surface cannot subtend an angle greater than 180°. If
necessary, append two arcs to create an arc that subtends an angle of more than 180°. There is no such
limitation for deformable bodies or discrete rigid surfaces.
You should take care positioning points while sketching because this positioning can affect the quality
of your mesh. Points in the sketch become vertices of the part you are creating or modifying. In turn,
when you mesh your model in the Mesh module, ABAQUS/CAE converts these vertices into fully
constrained seeds and places nodes at their location. For information on how to subsequently move
vertices, see ``Moving and resizing Sketcher objects by moving their vertices,'' Section 22.12.1. For
information on how to subsequently move vertices that define arcs, see ``Moving and resizing Sketcher
objects by moving their vertices,'' Section 22.12.1.
Detailed instructions for sketching an arc using a center point and two endpoints:
1. From the arc tools in the Sketcher toolbox, select the three-point arc tool . For a diagram of
the tools in the Sketcher toolbox, see ``The Sketcher tools,'' Section 22.4.1.
ABAQUS/CAE displays prompts in the prompt area to guide you through the procedure.
9-772
The Sketch module
ABAQUS/CAE draws a circle showing the radius of the arc as you move the cursor from the
center of the arc to its first endpoint.
Tip: If necessary, click the previous step button to reverse the selection of the endpoints.
5. To create more arcs, repeat the above steps beginning with Step 2.
You should take care positioning points while sketching because this positioning can affect the quality
9-773
The Sketch module
of your mesh. Points in the sketch become vertices of the part you are creating or modifying. In turn,
when you mesh your model in the Mesh module, ABAQUS/CAE converts these vertices into fully
constrained seeds and places nodes at their location. For information on how to subsequently move
vertices, see ``Moving and resizing Sketcher objects by moving their vertices,'' Section 22.12.1. For
information on how to subsequently move vertices that define arcs, see ``Moving and resizing Sketcher
objects by moving their vertices,'' Section 22.12.1.
Detailed instructions for sketching an arc tangent to a line:
1. From the arc tools in the Sketcher toolbox, select the tangent arc tool . For a diagram of the
tools in the Sketcher toolbox, see ``The Sketcher tools,'' Section 22.4.1.
ABAQUS/CAE displays prompts in the prompt area to guide you through the procedure.
2. Select the point along the line or curve. The arc will be tangent at this point.
If more than one line or curve meets at the point, the arc will be tangent to the one that was most
recently created.
3. The radius of the arc changes as you move the cursor. Click at the desired endpoint.
Tip: If necessary, you can use the text box in the prompt area to enter the precise coordinates
of the center and the endpoint of the arc. For more information on creating the desired arc, see
``Specifying precise geometry,'' Section 22.6.
4. To create more arcs, repeat the above steps beginning with Step 2.
9-774
The Sketch module
``Construction geometry,'' Section 22.5.2, illustrates how you can create a fillet tangent to two
construction circles.
You should take care positioning points while sketching because this positioning can affect the quality
of your mesh. Points in the sketch become vertices of the part you are creating or modifying. In turn,
when you mesh your model in the Mesh module, ABAQUS/CAE converts these vertices into fully
constrained seeds and places nodes at their location. For information on how to subsequently move
vertices, see ``Moving and resizing Sketcher objects by moving their vertices,'' Section 22.12.1.
If you create a fillet and subsequently move the selected lines or circles, ABAQUS/CAE will move the
fillet and maintain the tangency.
Detailed instructions for sketching a fillet between two lines:
1. From the Sketcher toolbox, select the fillet tool . For a diagram of the tools in the Sketcher
toolbox, see ``The Sketcher tools,'' Section 22.4.1.
ABAQUS/CAE displays prompts in the prompt area to guide you through the procedure.
2. In the text box that appears in the prompt area, enter the radius of the desired fillet.
3. Select the two lines or circles (not arcs) to which the fillet must remain tangent.
The fillet appears between the two lines or circles.
Tip: When you select a line or circle from the sketch, ABAQUS/CAE uses the cursor position
to determine the location of the fillet. To create the desired fillet, you should position the
cursor close to the expected location of the fillet when making a selection.
4. To create more fillets of the same radius, repeat the previous step.
9-775
The Sketch module
When you create an analytical rigid surface, you sketch a sequence of lines, arcs, and parabolas to
define its profile. To create a parabolic curve, sketch a spline defined by only three vertices.
Detailed instructions for sketching splines:
1. From the Sketcher toolbox, select the spline tool . For a diagram of the tools in the
9-776
The Sketch module
The spline appears as you click each vertex or enter each coordinate, and ABAQUS/CAE adjusts
the curve to maintain a cubic spline between all points.
Tip: If you make a mistake while constructing a spline, you can click the previous step button
to step back to the previous vertex. Alternatively, you can click the Undo button in the
Sketcher toolbox to delete the entire spline.
4. To create more splines, repeat the above steps beginning with step 2.
9-777
The Sketch module
You can also use a horizontal construction line to define the axis of rotation for revolved solids and
surfaces.
Detailed instructions for sketching a horizontal construction line:
1. From the construction tools in the Sketcher toolbox, select the horizontal construction tool .
For a diagram of the tools in the Sketcher toolbox, see ``The Sketcher tools,'' Section 22.4.1.
The horizontal construction line moves vertically as you move the cursor around the Sketcher
sheet. ABAQUS/CAE displays prompts in the prompt area to guide you through the procedure.
2. Click a point that will lie on the horizontal construction line. Alternatively, you can type its X-Y
coordinates in the text field that appears in the prompt area. (The X-coordinate is arbitrary since it
is ignored.)
9-778
The Sketch module
You can also use a vertical construction line to define the axis of rotation for revolved solids and
surfaces.
9-779
The Sketch module
1. From the construction tools in the Sketcher toolbox, select the vertical construction tool .
For a diagram of the tools in the Sketcher toolbox, see ``The Sketcher tools,'' Section 22.4.1.
The vertical construction line moves horizontally as you move the cursor around the Sketcher
sheet. ABAQUS/CAE displays prompts in the prompt area to guide you through the procedure.
2. Click a point that will lie on the vertical construction line. Alternatively, you can type its X-Y
coordinates in the text field that appears in the prompt area. (The Y-coordinate is arbitrary since it
is ignored.)
9-780
The Sketch module
You can also use an oblique construction line to define the axis of rotation for revolved solids and
surfaces.
Detailed instructions for sketching an oblique construction line:
1. From the construction tools in the Sketcher toolbox, select the oblique construction tool .
For a diagram of the tools in the Sketcher toolbox, see ``The Sketcher tools,'' Section 22.4.1.
ABAQUS/CAE displays prompts in the prompt area to guide you through the procedure.
2. Click two points that will lie on the oblique construction line. Alternatively, you can type their X-Y
coordinates in the text field that appears in the prompt area.
The oblique construction line appears when you select the first point. The line rotates about this
point until you select the second point.
9-781
The Sketch module
You can also use an angled construction line to define the axis of rotation for revolved solids and
surfaces.
Detailed instructions for sketching an angled construction line:
1. From the construction tools in the Sketcher toolbox, select the angled construction line tool .
For a diagram of the tools in the Sketcher toolbox, see ``The Sketcher tools,'' Section 22.4.1.
ABAQUS/CAE displays prompts in the prompt area to guide you through the procedure.
2. In the text box that appears in the prompt area, enter an angle. Enter the angle in degrees measured
9-782
The Sketch module
counterclockwise from the horizontal axis; you cannot enter negative angles.
The construction line moves as you move the cursor around the Sketcher sheet.
3. Click a point that will lie on the angled construction line. Alternatively, you can type its X-Y
coordinates in the text field that appears in the prompt area.
4. To create additional angled construction lines, repeat the above steps beginning with Step 2.
9-783
The Sketch module
1. From the construction tools in the Sketcher toolbox, select the construction circle tool . For
a diagram of the tools in the Sketcher toolbox, see ``The Sketcher tools,'' Section 22.4.1.
ABAQUS/CAE displays prompts in the prompt area to guide you through the procedure.
2. Click at the desired location of the center of the construction circle. Alternatively, you can type the
X-Y coordinates of the circle center in the text field that appears in the prompt area.
The radius of the construction circle changes as you move the cursor around the Sketcher sheet.
3. Click a point that will lie on the circumference of the construction circle, or type its X-Y
coordinates in the prompt area.
4. To create more construction circles, repeat the above steps beginning with Step 2.
9-784
The Sketch module
9-785
The Sketch module
Note: If you want to create a horizontal dimension between vertical lines, the lines must be
exactly vertical and align with the Sketcher grid.
1. From the dimension tools in the Sketcher toolbox, select the horizontal dimension tool . For
a diagram of the tools in the Sketcher toolbox, see ``The Sketcher tools,'' Section 22.4.1.
ABAQUS/CAE displays prompts in the prompt area to guide you through the procedure.
3. Move the cursor vertically to the location where you would like the horizontal dimensioning line
to appear; click when you are satisfied with the appearance of the dimension.
4. To create additional horizontal dimensions, repeat the above steps beginning with Step 2.
· ``Moving and resizing Sketcher objects by modifying their dimensions,'' Section 22.12.2
9-786
The Sketch module
Note: If you want to create a vertical dimension between horizontal lines, the lines must be
exactly horizontal and align with the Sketcher grid.
1. From the dimension tools in the Sketcher toolbox, select the vertical dimension tool . For a
diagram of the tools in the Sketcher toolbox, see ``The Sketcher tools,'' Section 22.4.1.
ABAQUS/CAE displays prompts in the prompt area to guide you through the procedure.
3. Move the cursor horizontally to the location where you would like the vertical dimensioning line
to appear; click when you are satisfied with the appearance of the dimension.
4. To create additional vertical dimensions, repeat the above steps beginning with Step 2.
9-787
The Sketch module
· ``Moving and resizing Sketcher objects by modifying their dimensions,'' Section 22.12.2
9-788
The Sketch module
1. From the dimension tools in the Sketcher toolbox, select the oblique dimension tool . For a
diagram of the tools in the Sketcher toolbox, see ``The Sketcher tools,'' Section 22.4.1.
ABAQUS/CAE displays prompts in the prompt area to guide you through the procedure.
3. Move the cursor to the location where you would like the dimensioning line to appear; click when
you are satisfied with the appearance of the dimension.
4. To create additional oblique dimensions, repeat the above steps beginning with Step 2.
· ``Moving and resizing Sketcher objects by modifying their dimensions,'' Section 22.12.2
9-789
The Sketch module
To create an angular dimension, select the two lines and the position of the dimensioning arc, as shown
in the following figure:
1. From the dimension tools in the Sketcher toolbox, select the angular dimension tool . For a
diagram of the tools in the Sketcher toolbox, see ``The Sketcher tools,'' Section 22.4.1.
ABAQUS/CAE displays prompts in the prompt area to guide you through the procedure.
3. Move the cursor to the location where you would like the dimensioning line to appear; click when
you are satisfied with the appearance of the dimension.
4. To create additional angular dimensions, repeat the above steps beginning with Step 2. Repeat the
above steps beginning with step 2.
9-790
The Sketch module
· ``Moving and resizing Sketcher objects by modifying their dimensions,'' Section 22.12.2
1. From the dimension tools in the Sketcher toolbox, select the radial dimension tool . For a
diagram of the tools in the Sketcher toolbox, see ``The Sketcher tools,'' Section 22.4.1.
ABAQUS/CAE displays prompts in the prompt area to guide you through the procedure.
3. Move the cursor to the location where you would like the end of the dimensioning arrow to
appear; click when you are satisfied with the appearance of the dimension.
9-791
The Sketch module
4. To create additional radial dimensions, repeat the above steps beginning with Step 2.
· ``Moving and resizing Sketcher objects by modifying their dimensions,'' Section 22.12.2
· ``Moving and resizing Sketcher objects by moving their vertices,'' Section 22.12.1
· ``Moving and resizing Sketcher objects by modifying their dimensions,'' Section 22.12.2
9-792
The Sketch module
Detailed instructions for moving or resizing Sketcher objects by moving their vertices:
1. From the modify tools in the Sketcher toolbox, select the vertex modification tool . For a
diagram of the tools in the Sketcher toolbox, see ``The Sketcher tools,'' Section 22.4.1.
Handles appear on all vertices in the viewport. ABAQUS/CAE displays prompts in the prompt
area to guide you through the procedure.
2. Select the appropriate vertices of the objects you want to move or resize.
Which vertices you select depends on what type of object you selected and whether you want to
move or resize it.
Tip: In cases where you must select more than one vertex, hold down the [Shift] key as you
click each handle. To select multiple vertices, you can also drag a rectangle around them. To
unselect a vertex, use [Ctrl]+Click. When you are finished selecting vertices, click mouse
button 2. For more information, see Chapter 9, "Selecting objects within the viewport."
3. Use the buttons that appear in the prompt area to indicate how you will specify a new location for
the selected vertices.
· Select Translate to translate the selected vertices along a specified vector. You can define the
start and the end of the translation vector by either selecting from the sketch or typing the X-
and Y-coordinates of each end.
· Select Rotate to rotate the selected vertices through a specified angle about a specified point.
You can specify the point at the center of rotation by selecting from the sketch or by typing the
X- and Y-coordinates. The angle of rotation you specify must be between 360 and -360
degrees.
4. To move or resize more objects, repeat the above steps beginning with step 2.
9-793
The Sketch module
1. From the modify tools in the Sketcher toolbox, select the dimension modification tool . For
a diagram of the tools in the Sketcher toolbox, see ``The Sketcher tools,'' Section 22.4.1.
ABAQUS/CAE displays prompts in the prompt area to guide you through the procedure.
3. Select the appropriate vertices of the objects you want to move or resize.
Which vertices you select depends on what type of object you selected and whether you want to
move or resize it.
Tip: In cases where you must select more than one vertex, hold down the [Shift] key as you
click each handle. To select multiple vertices, you can also drag a rectangle around them. To
unselect a vertex, use [Ctrl]+Click. When you are finished selecting vertices, click mouse
button 2. For more information, see Chapter 9, "Selecting objects within the viewport."
4. Use the text box in the prompt area to enter a new value for the dimension.
The object moves or resizes to accomodate the new dimension.
5. To move or resize more objects, repeat the above steps beginning with Step 2.
9-794
The Sketch module
1. From the Sketcher toolbox, select the Copy tool . For a diagram of the tools in the
Sketcher toolbox, see ``The Sketcher tools,'' Section 22.4.1.
ABAQUS/CAE displays prompts in the prompt area to guide you through the procedure.
2. Select all the objects that you want to copy. Both sketch and construction geometry can be copied;
reference geometry and dimensions cannot be copied.
Tip: In cases where you must select more than one vertex, hold down the [Shift] key as you
click each handle. To select multiple vertices, you can also drag a rectangle around them. To
unselect a vertex, use [Ctrl]+Click. When you are finished selecting vertices, click mouse
button 2. For more information, see Chapter 9, "Selecting objects within the viewport."
3. Use the buttons that appear in the prompt area to indicate how you will specify a new location for
the copied objects.
· Select Translate to translate the copied objects along a specified vector. You can define the
beginning and the end of the translation vector by either selecting from the sketch or typing the
X- and Y-coordinates of each end.
· Select Rotate to rotate the copied objects through a specified angle about a specified point.
You can specify the point at the center of rotation by selecting from the sketch or typing the X-
and Y-coordinates. The angle of rotation you specify must be between 360 and -360 degrees.
4. To copy more objects, repeat the above steps beginning with step 2.
9-795
The Sketch module
· ``Moving and resizing Sketcher objects by moving their vertices,'' Section 22.12.1
· ``Moving and resizing Sketcher objects by modifying their dimensions,'' Section 22.12.2
1. From the Sketcher toolbox, select the Delete tool . For a diagram of the tools in the
Sketcher toolbox, see ``The Sketcher tools,'' Section 22.4.1.
ABAQUS/CAE displays prompts in the prompt area to guide you through the procedure.
2. Select all the objects you want to delete. Both sketch and construction geometry can be deleted;
reference geometry cannot be deleted.
Tip: In cases where you must select more than one vertex, hold down the [Shift] key as you
click each handle. To select multiple vertices, you can also drag a rectangle around them. To
unselect a vertex, use [Ctrl]+Click. When you are finished selecting vertices, click mouse
button 2. For more information, see Chapter 9, "Selecting objects within the viewport."
9-796
The Sketch module
Tip: To restore accidentally deleted objects, click the Undo button in the Sketcher toolbox.
4. To delete more objects, repeat the above steps beginning with step 2.
Use the Undo tool from the Sketcher toolbox to undo your previous operation. For a diagram
of the tools in the Sketcher toolbox, see ``The Sketcher tools,'' Section 22.4.1.
Depending on your previous action, clicking Undo can have the following effect:
· Remove the object just created. Objects include sketch geometry (lines, arcs, circles, fillets,
splines, or points), construction geometry, or dimensions.
· Restore the sketch to its state prior to the move, resize, copy, or delete operation just
performed.
· Remove a retrieved stand-alone sketch, provided you have not positioned the sketch. Once you
have positioned the retrieved sketch, clicking Undo moves the origin of the retreived sketch back
to the origin of the current sketch.
You can undo only the previous action; prior actions cannot be undone.
If you click Undo a second time, ABAQUS/CAE cancels the effect of the first undo operation. For
example, if you sketch a line and click Undo, ABAQUS/CAE deletes the line. If you click Undo
again, ABAQUS/CAE restores the line.
9-797
The Sketch module
· The Create, Edit, Copy, Rename, and Delete items listed under the Sketch menu on the main
menu bar. Each item contains a submenu listing all the sketches in the current model.
· The Sketch Manager dialog box. The Sketch Manager contains functions identical to those
listed under the Sketch menu, but with a convenient browser that lists all the sketches available in
the current model. To display the Sketch Manager dialog box, select Sketch->Manager from the
main menu bar.
Note: The Sketch menu and the Sketch Manager are available only from the Sketch module.
When you are sketching a feature in the Part module, for example, the Sketch menu and the
Sketch Manager are not available.
9-798
The Sketch module
Tip: You can also create a stand-alone sketch by clicking the sketch create tool in the
Sketch module toolbox.
2. In the Create Sketch dialog box, enter a name for the sketch. For information on valid names, see
``Using basic dialog box components,'' Section 6.3.1.
3. In the Create Sketch dialog box, enter the approximate size of the sketch.
The size that you enter is used by ABAQUS/CAE to calculate the size of the sheet and the spacing
of its grid. The approximate size should reflect the largest dimension of the sketch and must be
between 105 and 10-3 units. ABAQUS/CAE does not require specific units, but the units must be
consistent throughout the model.
5. When you have finished sketching, click Done in the prompt area.
9-799
The Sketch module
1. From the Sketcher toolbox, select the save as tool . For a diagram of the tools in the
Sketcher toolbox, see ``The Sketcher tools,'' Section 22.4.1.
2. In the text field that appears in the prompt area, enter the name of the sketch.
ABAQUS/CAE saves the sketch and returns to the Sketcher.
1. From the Sketcher toolbox, select the add sketch tool . For a diagram of the tools in the
Sketcher toolbox, see ``The Sketcher tools,'' Section 22.4.1.
ABAQUS/CAE displays the Add Sketch dialog box.
2. Select the sketch to add from the list of stand-alone sketches and click OK to close the Add
Sketch dialog box.
· Positions the added sketch so that its origin is coincident with the origin of the current sketch.
· Resizes the view so that both the current sketch and the added sketch are visible.
9-800
The Sketch module
3. Use the buttons that appear in the prompt area to indicate how you will locate the added sketch.
· Select Translate to translate the added sketch along a specified vector. You can define the
beginning and the end of the translation vector by either selecting from the sketch or by typing
the X- and Y-coordinates of each end.
· Select Rotate to rotate the added sketch through a specified angle about a specified point. You
can specify the point at the center of rotation by selecting from the sketch or typing the X- and
Y-coordinates. The angle of rotation you specify must be between 360 and -360 degrees.
9-801
Viewing results
· Chapter 24, "Selecting model data and analysis results to plot "
0-802
Visualization module basics
Fast plot
A fast plot is a quickly drawn representation of your model.
X-Y plotting
1-803
Visualization module basics
Stress linearization
Stress linearization is the separation of stresses through a section into constant membrane and
linear bending stresses. You specify the section as a path through your model, and the
Visualization module displays the linearized stresses in the form of an X-Y plot.
Animation
An animation is a sequence of images that the Visualization module displays in rapid
succession, resulting in a movie-like effect.
Plot customization
The Visualization module provides numerous options that you can use to customize your
plots.
1-804
Visualization module basics
· Fast
· Undeformed shape
· Deformed shape
· Contour
· Symbol
· Material orientation
Each of these plots corresponds to a plot mode. Plot modes are important because most of the
customization options provided by the Visualization module are plot mode-dependent, which means
that they pertain only to a particular plot mode.
1-805
Visualization module basics
produce an undeformed plot, the current viewport will then be in the undeformed plot mode. The plot
mode of a viewport persists until you produce a plot in some other mode in that viewport. If you create
multiple viewports, each viewport can be in a different plot mode.
The plot mode of the current viewport is identified on the left side of the prompt area, as shown in the
following figure:
1-806
Visualization module basics
Plot mode-independent options are those that affect all plots collectively. These are options
governing the viewpoint, graphics, individual item coloring, and such general characteristics
as plot legends, axisymmetric sweeping, and the appearance of text blocks giving the model's
title and state.
Plot mode-dependent options affect such plot attributes as the render style (for example, filled or
wireframe model rendering), visible edges, and line thickness of your model. You control these
attributes separately for each plot mode using the options associated with that mode. To choose the
render style of your undeformed plot, for example, you must use the Undeformed plot options. To do
so, you can select Options->Undeformed from the main menu bar. Alternatively, you can use the
Undeformed Options button on the right side of the prompt area, as shown in the following figure:
The Options buttons provide quick access to the plot mode-dependent customization options
applicable to the current viewport. Depending on the current plot mode, the right side of the prompt
area contains zero, one, or two Options buttons. If you have an X-Y plot in the current viewport, both
Curve Options and Plot Options buttons appear because both categories of options are applicable.
Similarly, if you are in the scale factor or time history animation mode, two Options buttons appear. If
the current viewport is in the fast plot mode, there are no plot mode-dependent customization options,
and no Options button appears.
Plot mode-dependent options affect only plots in the associated mode. If you select a render style from
the undeformed plot options dialog box, that render style will affect only undeformed plots. If the
current viewport is in the undeformed plot mode, you will see the effect of your changes when you
click Apply or OK in the undeformed plot options dialog box. However, if the current viewport is not
in the undeformed plot mode, you will not see the effect of your changes until you produce an
undeformed plot in the current viewport.
Plot mode-independent options affect plots across all plot modes. For example, if you select
View->Viewport Annotations from the main menu bar to suppress the appearance of the view triad,
the view triad will be suppressed for plots in all plot modes. For more information on customizing
plots, see Chapter 37, "Customizing model display."
1-807
Visualization module basics
multiple viewports, you must first designate a particular viewport as current to change its display.
Customization selections you apply affect only the current viewport. When you designate a viewport as
current, the options dialog boxes are refreshed to show the state of options associated with that
viewport. For more information on working with viewports, see ``Working with viewports,'' Section
7.3.
1-808
Selecting model data and analysis results to plot
· Frame: Control the step and frame at which ABAQUS/CAE obtains results.
· Section Points: Control which section points provide shell and beam results for integration point
variables.
· Field Output: The Field Output dialog box contains the following tabs:
- Primary Variable: Control the variable and, if applicable, the invariant or component for
which ABAQUS/CAE displays results.
2-809
Selecting model data and analysis results to plot
- Deformed Variable: Control the variable ABAQUS/CAE uses to display the deformed model
shape.
- Result Options: Choose to display field output or discontinuities, control the averaging of
element-based field output results, and control the computation of results at region boundaries.
It is possible to open an output database for an analysis that is still in progress. As the analysis moves
toward completion, the lists of completed steps and frames are updated every time you close and then
reopen the Frame Selector dialog box.
This section explains the following topics:
2-810
Selecting model data and analysis results to plot
3. From the Frame list, click the frame to display. Select Frame 0 to display the base state of the
current step; for example, to contour initial stresses.
The selected frame is highlighted.
· Chapter 24, "Selecting model data and analysis results to plot "
2-811
Selecting model data and analysis results to plot
You can use the ODB Frame control buttons available in the prompt area to step through results
frames. Available frames consist of those for which analysis results have been saved. For information
on selecting a specific results frame, see ``Selecting a specific results step and frame,'' Section 24.2.1.
To step through results frames:
1. Locate the ODB Frame buttons. These buttons appear on the left side of the prompt area when you
are in the undeformed, deformed, contour, or symbol plot mode.
· First frame of step to display results from the first frame of the current step. This button has
no effect if you are already displaying results from the first frame of the step.
· Previous frame to display results from the previous frame. If you are currently displaying
results from the first frame of a step, ABAQUS/CAE will display results from the last frame of
the previous step. This button has no effect if you are already displaying results from the first
frame of the first step.
· Next frame to display results from the next frame. If you are currently displaying results from
the last frame of a step, ABAQUS/CAE will display results from the first frame of the next
step. This button has no effect if you are already displaying results from the last frame of the
last step.
· Last frame of step to display results from the last frame of the current step. This button has
no effect if you are already displaying results from the last frame of the step.
The model plot in the current viewport changes to show your model at the step and frame you have
selected. If active, the text in the state block changes to identify the selected step and frame.
ABAQUS refreshes the Frame Selector dialog box, highlighting the selected step and frame and
the Field Output dialog box, listing variables available for the frame you have selected. ABAQUS
also refreshes all dialog boxes in which the current step and frame are identified.
2-812
Selecting model data and analysis results to plot
· Chapter 24, "Selecting model data and analysis results to plot "
· ``Selecting the location of shell and beam output variables, '' Section 24.3.4
To learn how to select output database history output to produce an X-Y plot, see ``Reading X-Y data
from output database history output,'' Section 30.2.1. To learn how to select output database field
output to produce an X-Y plot, see ``Reading X-Y data from output database field output, '' Section
30.2.2.
2. Select the primary and deformed field output variables that you want as described in the following
sections:
2-813
Selecting model data and analysis results to plot
· ``Selecting the location of shell and beam output variables, '' Section 24.3.4
The model plot in the current viewport changes to show the variables you have selected. If active,
the text in the legend and state block changes to identify the variables associated with the plot. For
more information on the legend and state block, see ``Customizing the legend,'' Section 38.1, and
``Customizing the state block,'' Section 38.3. In addition, ABAQUS refreshes all dialog boxes in
which the currently selected variables are identified.
· Chapter 24, "Selecting model data and analysis results to plot "
1. Locate the options that control the primary field output variable.
From the main menu bar, select Result->Field Output. Click the Primary Variable tab in the
dialog box that appears.
The Primary Variable options appear.
Tip: You can also access these options by clicking the Field Output button in any dialog box
in which it appears.
To see the complete descriptions of the variables listed, increase the width of the dialog box by
dragging one corner.
a. Toggle List only variables with results to display a list that is limited by the storage
location of the variables. Limiting the list helps you select variables by presenting, for
example, only integration point quantities.
2-814
Selecting model data and analysis results to plot
When List only variables with results is on, filter options become available in the pull
down menu.
b. Click the List only variables with results arrow to reveal the filter options.
c. Click the text stating the location of the variables you want to include in the Name and
Description list.
The text appears in the List only variables with results box, and the Name and
Description list is refreshed to include only variables having that location.
3. From the Name and Description list, click the name of the analysis variable that you want.
The selected variable is highlighted. If applicable, the Component and Invariant lists on the
bottom of the dialog box are refreshed to display available components or invariants, respectively.
4. If items are listed in the Component or Invariant list, click the component or invariant that you
want.
The selected component or invariant is highlighted.
· Chapter 24, "Selecting model data and analysis results to plot "
1. Locate the options that control the deformed field output variable.
From the main menu bar, select Result->Field Output. Click the Deformed Variable tab in the
dialog box that appears.
2-815
Selecting model data and analysis results to plot
ABAQUS/CAE lists by name and description all variables available at the current step and frame
of your output database that can be used for a deformed plot (nodal vector quantities). To see the
complete descriptions of the variables listed, increase the width of the dialog box by dragging one
corner.
2. From the Name and Description list, click the deformed field variable that you want.
The selected variable is highlighted.
· Chapter 24, "Selecting model data and analysis results to plot "
2-816
Selecting model data and analysis results to plot
The Current section point settings field at the top of the dialog box displays a list of element
categories. The elements within each category share common section properties, such as those listed
below:
The label for each category includes information about the section properties of the elements within
the category. For example, the first category label that appears in the Category list in Figure 24-1
indicates the following:
The Location list in the Current section point settings field displays the location of the section
point from which output is currently displayed for each category. In many cases the location of a
section point is described in terms of its position relative to the midpoint of the cross- section. For
two-dimensional beams, this relative position is reported as a fraction of the distance between the
2-817
Selecting model data and analysis results to plot
midpoint of the cross-section and the top or bottom surface of the section. For shells, this relative
position is reported as a fraction of the distance between the midpoint of the cross- section and the
SPOS or SNEG surface of the section. A list of all of the available section point locations for the
selected category appears in the Available Section Points in Cross Section field at the bottom of the
dialog box.
For example, in Figure 24-1 the selected category contains a shell section with five section points.
Therefore, the Available Section Points in Cross Section field contains a list of the five section
point locations. The section point in the middle of the section is Mid, fraction = 0.0; the
section point between the middle of the section and the SPOS surface is fraction = 0.5; the
section point between the middle of the section and the SNEG surface is fraction = -0.5; and so
on.
For beams with three-dimensional sections, the relative position of a section point can be reported as a
fraction of the distance between the midpoint of the cross- section and
· the top or bottom of the section (along the local 2-axis of the section) or
· the left or right side of the section (along the local 1-axis of the section).
For example, Figure 24-2 shows the section point locations in a three-dimensional L- section beam.
In other cases, angles or section point numbers are used to indicate section point locations. For
example, Figure 24-3 shows the section point locations in a three-dimensional pipe section.
2-818
Selecting model data and analysis results to plot
For more information about where section points are located in different section types, see the
following:
· ``Beam elements,'' Section 15.3 of the ABAQUS/Standard User's Manual and Section 14.3 of the
ABAQUS/Explicit User's Manual
· ``Shell elements,'' Section 15.6 of the ABAQUS/Standard User's Manual and Section 14.4 of the
ABAQUS/Explicit User's Manual
2. In the Category field of the dialog box, select the element category or categories for which you
want to change the output location.
The Available Section Points in Cross Section field in the bottom half of the dialog box
changes to list the locations of the section points from which output was saved for the category
you have selected. If you have selected more than one category, only those locations that are
common to all of the selected categories appear in the list.
3. In the Available Section Points in Cross Section field, select the section point location of your
choice.
The location listed for the selected categories in the Current section point settings field changes
to reflect your selection.
4. In the Section Points dialog box, click OK to apply your settings and to exit the dialog box.
The model plot in the current viewport changes to display values from the specified section points.
The plot legend, if active, changes to identify the specified section points. For information about
the plot legend, see ``Customizing the legend,'' Section 38.1.
Results for subsequent tabular reports, model probing, and X-Y data objects along a path will be
obtained from the section points you have specified.
2-819
Selecting model data and analysis results to plot
· Chapter 24, "Selecting model data and analysis results to plot "
2-820
Selecting model data and analysis results to plot
· share the same basic element type (continuum, shell, beam, etc.),
· use interpolation functions of the same order (first-order elements versus second-order
elements), and
· have the same integration scheme (reduced integration, full integration, etc.).
If all contributions at a node originate from a single result region, the values are combined as
necessary in further computations. If contributions are received from more than one result
region, you can choose to respect the region boundary and keep the contributions separate in
further computations or to ignore the region boundary and combine the values. For more
information, see ``Controlling computations at region boundaries, '' Section 24.4.5.
Finally, computations depend on whether you choose to display the field output values or
discontinuities; discontinuities are the differences in field output values between adjacent
elements.
· Field Output: For the display of field output values, the calculated invariants or
components at nodes common to two or more elements are averaged conditionally,
depending on the compatibility of contributing result regions and on options you select.
For more information, see ``Understanding result value averaging,'' Section 24.4.2.
2-821
Selecting model data and analysis results to plot
components at nodes common to two or more elements are compared to determine the
greatest difference, depending on the compatibility of contributing result regions and on
options you select. Nodes associated with only one element and nodes receiving
equivalent values from all contributing elements will show a value of zero in a plot of
discontinuities.
For more information, see ``Displaying field output values or discontinuities, '' Section 24.4.3.
The display of node-based field output variables (such as displacement), quilt contour plots, and plots
of discontinuities do not involve value averaging.
Extrapolated output database values at nodes common to two or more elements are averaged
conditionally. You can control the extent to which ABAQUS/CAE averages these values by selecting
the averaging criteria and whether averaging takes place across result regions.
The lower the averaging threshold you apply, the more the displayed values depict the individual
element results. Conversely, a higher averaging threshold produces a smoother effect with fewer
noticeable discontinuities from element to element.
ABAQUS/CAE averages values at nodes common to two or more elements when the contributing
elements lie in the same result region. You can choose whether or not ABAQUS/CAE averages values
at nodes common to two or more result regions. You can suppress averaging across regions to
emphasize visually any discontinuities at region boundaries, or you can request averaging across
regions to produce a more continuous effect. For example, Figure 24-4 shows a contour plot without
averaging across regions on the left and with averaging across regions on the right.
Figure 24-4 Contour plots without averaging and with averaging across regions.
2-822
Selecting model data and analysis results to plot
If you choose to average across regions, the extent to which values are averaged is controlled by the
averaging criteria that you specify as follows:
If the relative nodal variation for each node included in the plot is less than your averaging criteria,
values of contributing elements are averaged at that node. If the relative nodal variation exceeds your
criteria, the values are not averaged. When you decide to average across regions, the averaging criteria
are considered in relation to the variation of values across the whole model, not just across the nodes
included in the plot. Setting a high averaging criteria would allow you to smooth out all but the most
extreme discontinuities relative to results across your whole model.
If you choose not to average across regions, the extent to which values are averaged at nodes within
each region is controlled by the averaging criteria that you specify as follows:
If the relative nodal variation for each node included in the plot is less than your averaging criteria,
values of contributing elements are averaged at that node. If the relative nodal variation exceeds your
criteria, the values are not averaged. When you suppress averaging across regions, the averaging
criteria are considered in relation to the variation of values within each region rather than across the
whole model.
Select Result->Field Output->Result Options to locate the options that affect averaging.
``Controlling result averaging,'' Section 24.4.4, and ``Controlling computations at region boundaries, ''
Section 24.4.5, provide details on using the averaging options.
2-823
Selecting model data and analysis results to plot
Figure 24-5 displays a contour plot of field output values on the left and a contour plot of
discontinuities on the right.
Figure 24-5 Contour plots showing field output values and discontinuities in values.
2. Click Field output or Discontinuities to choose the quantity that you want to plot.
2-824
Selecting model data and analysis results to plot
The averaging threshold governs the extent of averaging. If the relative difference between
contributions at a node is greater than the percentage threshold you set, ABAQUS/CAE will not
average the contributing values and your results will appear discontinuous at that node. Use a higher
percentage to produce a smoother, more continuous effect.
For information on averaging across regions, see ``Controlling computations at region boundaries, ''
Section 24.4.5.
To control result averaging:
2. To set the averaging threshold, drag the Threshold (%) slider to the value that you want.
A value of 0 suppresses all averaging.
2-825
Selecting model data and analysis results to plot
2. To govern computations at nodes common to two or more result regions, toggle Ignore region
boundaries when computing values .
To ignore region boundaries means to combine values from incompatible result regions when
computing nodal averages or when computing discontinuities.
output to create new results called user field output objects. Use the tool in the toolbox to create
user field output objects, or select Tools->Field Output from the main menu bar to create, copy,
rename, or delete user field output objects.
This section covers the following topics:
For information on selecting and plotting previously saved field output, see ``Overview of field output
variable selection,'' Section 24.3.1. For more information on using managers, see ``Managing objects
using manager dialog boxes,'' Section 6.5.6.
2-826
Selecting model data and analysis results to plot
To define a new user field output object, you build an arithmetic expression in the text field of the
Operate on Field Output dialog box.
An expression is composed of one or more previously created field output names, one or more
operators, and, optionally, parentheses and scalars. User field output object names must be surrounded
by quotation marks. See ``Overview of operations on field output,'' Section 24.5.2, for information on
supported operators.
User field output objects can consist of different types of data that may not be compatible. The
Operate on Field Output dialog box lists the type of each user field output object as one of four
general types: scalar, vector, tensor, and quaternion. The tensor types are further subdivided into five
subtypes that describe the dimensionality of the tensor and the components available. The following
rules apply:
· The multiplication and division operations are not supported between two vector objects nor
between two tensor objects.
· Operations on tensors are performed on the tensor component data that ABAQUS/CAE reads from
the output database. Subsequently, the display of the resulting user-defined field output object may
give unexpected values for extrapolated components or for computed invariants. For example, if
the components of a stress tensor are negative, applying the absolute value operation to the stress
tensor will produce positive values for the stress components, but the values of pressure--an
invariant computed after the absolute value operation has been applied--may be negative.
Similarly, applying the sine operation to a stress tensor will produce component values within the
range {-1, 1}, but the extrapolation used to compute contour values of such components may
produce values beyond this range.
· Operations on tensors are performed in the local coordinate system, if it is available; otherwise, the
global system is used. ABAQUS/CAE assumes that the local coordinate systems are consistent for
operations involving more than one tensor.
· If more than one field output object appears in an expression, the expression produces new results
only at those locations for which all referenced field output is available. Locations for which
necessary data are not available are evaluated as having no results.
Example 1
To create a user field output object by finding the difference in the stress fields for two
increments, type:
("stress at inc 2") - ("stress at inc 1")
in the expression text field of the Operate on Field Output dialog box.
2-827
Selecting model data and analysis results to plot
"stress at inc 2" and "stress at inc 1" are field output objects representing
stress at two different increments of a particular step. The result of this equation is a user field
output object representing the difference in the stress fields for the two increments.
Example 2
To create a user field output object by combining load cases at several steps, type:
("dead_load" * 3) + ("wind" * 1.5) + ("snow" * 2)
in the expression text field of the Operate on Field Output dialog box.
"dead_load", "wind", and "snow" are the reaction forces (RF) at increment 1 of Steps
1, 2, and 3, respectively. The result of this equation is a user field output object representing
the linear combination of scaled load cases at three different results steps.
Example 3
To create a user field output object by expressing pressure in decibels as a function of pore
pressure, type:
20.0 * log10(``POR''/``Pref'')
in the expression text field of the Operate on Field Output dialog box.
"Pref" is the reference pressure. The result of this equation is a user field output object
representing pressure in decibels as a function of the analysis variable POR.
2-828
Selecting model data and analysis results to plot
/ Perform division.
abs(A) Take the absolute value.
acosA) Take the arccosine.
asin(A) Take the arcsine.
atan(A) Take the arctangent.
cos(A) Take the cosine.
degreeToRadian(A) Convert degrees to radians.
exp(A) Take the natural exponential.
exp10(A) Take the base 10 exponential.
log(A) Take the natural logarithm.
log10(A) Take the base 10 logarithm.
power(FO,F) Raise a field output object to a power.
radianToDegree(A) Convert radians to degrees.
sin(A) Take the sine.
sqrt(A) Take the square root.
tan(A) Take the tangent.
2-829
Selecting model data and analysis results to plot
· Click ODB field output to select and save analysis results as user field output. You
must choose this option to make field output available for operations.
· Click User-defined field output to create new field output by operating on user field
output that you have previously created.
b. Click Continue.
ABAQUS displays either the Field Output or Operate on Field Output dialog box, according to
your selection.
5. The default name for the field output object appears in the Name text field. To provide a more
meaningful name, replace this default with the name of your choice (including blank spaces if you
wish).
2-830
Selecting model data and analysis results to plot
a. Click on user field output object names and built-in operators in the dialog box to select
them. Use drag-select for multiple contiguous field output object name selection.
b. Use standard mouse and keyboard editing techniques to position the cursor and configure
your expression.
c. Adjust the syntax of your expression if necessary: field output object names must be
surrounded by quotation marks, and parentheses may be needed.
For more information, see ``Building valid user field output expressions, '' Section 24.5.1.
4. The default name for the field output object appears in the Name text field. To provide a more
meaningful name, replace this default with the name of your choice (including blank spaces if you
wish).
2-831
Selecting model data and analysis results to plot
7. When you are done, click Cancel to close the dialog box.
2-832
Plotting the undeformed shape
· Color & Style: Control model edge color and style and model face color.
3-833
Plotting the undeformed shape
· Labels: Control element, face, and node labels and node symbols.
To learn how to customize the render style and other display characteristics of your undeformed plot,
see Chapter 37, "Customizing model display."
1. Use the File menu to open the output database containing your model data. For the purpose of
undeformed plotting, analysis results need not be available; an output database resulting from a
datacheck run is sufficient.
3. Select the plot mode-independent and undeformed shape customization options that you want.
Tip: You can also produce an undeformed plot using the tool in the toolbox.
The current viewport displays a customized undeformed plot at the specified step and frame of the
current output database. ABAQUS/CAE is now in the undeformed plot mode.
In this mode ABAQUS automatically refreshes your undeformed plot each time you click Apply in
the results, plot mode-independent, or undeformed plot option dialog boxes. The current viewport
will remain in the undeformed plot mode until you produce a plot in some other (e.g., contour,
deformed) mode.
3-834
Plotting the deformed shape
· The deformed field output variable (see ``Selecting the deformed field output variable,'' Section
24.3.3).
· The analysis step and frame (see ``Selecting a specific results step and frame,'' Section 24.2.1).
· Uniform or nonuniform deformation scale factors (see ``Scaling deformations,'' Section 37.5.2).
You can also use ABAQUS/CAE to combine your undeformed and deformed model shapes into a
single plot. Combining the shapes provides a context for evaluating the deformations.
· Basic: Choose render style, edge visibility, and whether to superimpose the undeformed plot.
4-835
Plotting the deformed shape
· Color & Style: Control model edge color and style and model face color.
· Labels: Control element, face, and node labels and node symbols.
- Offset: Control the offset of the undeformed and the deformed shape.
To learn how to customize the render style and other display characteristics of your deformed plot, see
Chapter 37, "Customizing model display."
1. Use the File menu to open the output database containing your analysis results.
b. The deformed field variable for which ABAQUS obtains values. The variables that have
been saved during the analysis are available.
3. Select the plot mode-independent and deformed plot customization options that you want.
4-836
Plotting the deformed shape
Tip: You can also produce a deformed plot using the tool in the toolbox.
The current viewport displays a customized deformed plot of the specified deformation field
variable at the specified step and frame of the output database. The state block, if active, changes
to show the name of the variable displayed. ABAQUS/CAE is now in the deformed plot mode.
In this mode ABAQUS automatically refreshes your deformed plot each time you click Apply in
the results, plot mode-independent, or deformed plot options dialog boxes. The current viewport
will remain in the deformed plot mode until you produce a plot in some other (e.g., undeformed,
contour) mode.
4-837
Plotting the deformed shape
3. Toggle Show Undeformed Shape to request or suppress the display of the undeformed shape in
addition to the deformed shape.
Note: When Show Undeformed Shape is on, the position of the deformed shape relative to the undeformed shape is
controlled by the deformed plot Offset options.
4. Customize the offset of the deformed shape from the undeformed shape.
· Uniform to shift the position of the deformed shape equally in each of the X-, Y-, and
Z-directions.
When Uniform is on, a single offset value becomes available. In the Value field, enter
a single offset value to add uniformly to nodal X-, Y-, and Z-coordinates.
· Nonuniform to shift the position of the deformed shape unequally in the X-, Y-, and
Z-directions.
When Nonuniform is on, individual X-, Y-, and Z-direction offset values become
available. Click on each of the X, Y, and Z value boxes to enter offset values to add to
the nodal X-, Y-, and Z-coordinates, respectively.
4-838
Contouring analysis results
Figure 27-1 From left to right: contours shown as colored lines, colored bands, and colored faces.
As with other elements, contour lines for line-shaped elements (beams, one-dimensional elements,
gasket link elements, and three-dimensional line gasket elements, as well as two-dimensional contact
surfaces) are plotted along the elements by default. Tick mark contour plotting provides an alternative
means of visualizing contours on beams and other line-shaped elements. The contour is displayed as a
curve plotted between two sets of lines normal to the elements, as shown in Figure 27-2. The contour
level is indicated by "tick marks" on these normal lines.
5-839
Contouring analysis results
The key to interpreting a contour plot is the plot legend. The legend indicates the correspondence
between contour values and contour colors.
By default, ABAQUS/CAE evenly divides the difference between the minimum and maximum values
in the legend into 12 intervals. You can change the number of intervals if necessary. A color is
associated with each interval. For a line-type contour plot each colored contour line corresponds to a
set of locations in the model for which the field output variable has the value shown in the legend. For
a banded contour plot each colored contour band corresponds to a range of values within the bounds
indicated by the legend. For a quilt contour plot each colored element face corresponds to a single
value within the bounds indicated by the legend for that color. For a tick mark contour plot each
colored tick mark corresponds to a single value indicated by the legend.
This section discusses the computation of contour values and of contour limits. The following topics
are covered:
To learn how to produce a contour plot, see ``Producing a contour plot,'' Section 27.3.
5-840
Contouring analysis results
Select Result->Field Output from the main menu bar to choose the field output variable,
quantity to plot, and averaging options and to control the handling of incompatible elements
during the computation of element-based contour values. To learn more about these topics, see
``Selecting the field output to display,'' Section 24.3, and ``Selecting result options,'' Section
24.4.
Select Options->Contour->Basic from the main menu bar to choose the type of contour plot
that you want. ``Choosing line-, banded-, or quilt-type contours, '' Section 27.4.1 contains
detailed instructions on choosing the contour type.
The type of contour plot that you request governs the extrapolation applied to the results read
from the output database. For line- and banded-type contours of element-based variable
values, ABAQUS/CAE extrapolates results to the nodes and then conditionally averages these
results. For quilt-type contours of element-based variable values, ABAQUS/CAE extrapolates
results to the element faces on the surface of your model and then takes a weighted sum to
produce a single value per face. Since quilt contour values are computed for each element face
individually with no averaging across element boundaries, a quilt contour plot is an effective
means of displaying results on an element-by-element basis. You can choose quilt-type
contours only for element-based field output variables.
For a given element-based variable, a line- or banded-type contour plot with averaging
suppressed is not the same as a quilt-type contour plot. Quilt contour computation is based on
integration point values that are extrapolated to the element faces, whereas line and banded
contour computations are based on integration point values that are extrapolated to the nodes.
5-841
Contouring analysis results
If you request that ABAQUS/CAE compute the minimum and maximum over individual element
extrapolated values, the bounds for your plot will remain fixed even if you vary the averaging criteria.
This method yields bounds that most closely match the individual element results.
If you request that ABAQUS/CAE compute the minimum and maximum over values averaged at the
nodes, the limits are based on the values used to create the plot. In this case the legend bounds may
vary as you vary the averaging criteria. To learn how to control the averaging criteria, see ``Controlling
result averaging,'' Section 24.4.4.
For detailed information on controlling contour limits, see ``Setting contour limits,'' Section 27.4.6. To
learn how to display the minimum and maximum values associated with your contour plot, see
``Customizing the legend,'' Section 38.1.
· Basic: Choose the contour type (including whether to show tick marks for line elements),
intervals, render style, and edge visibility.
· Color & Style: The Color & Style page contains the following tabs:
- Model Edges: Control the color, style, and thickness of model edges.
- Line: For line-type contours control the style and thickness of each line.
- Banded: For banded-type contours control the color, style, and thickness of contour edges.
· Labels: Control element, face, and node labels and node symbols.
5-842
Contouring analysis results
To learn how to customize the render style and underlying model of your contour plot, see Chapter 37,
"Customizing model display." For information on the computation of result values, see
``Understanding how results are computed,'' Section 24.4.1.
1. Use the File menu to open the output database containing your analysis results.
c. The deformed field output variable to display (for contours on the deformed shape only).
3. Select the plot mode-independent and contour plot customization options that you want.
Tip: You can also produce a contour plot using the tool in the toolbox.
The current viewport displays a customized contour plot of the specified field output variable at
the specified step and frame of the current output database. ABAQUS/CAE is now in the contour
plot mode.
In this mode ABAQUS automatically refreshes your contour plot each time you click Apply in the
step and frame selector, field output options, plot mode-independent options, or contour plot
5-843
Contouring analysis results
options dialog boxes. The current viewport will remain in the contour plot mode until you produce
a plot in some other (e.g., undeformed or deformed) mode.
· Chapter 24, "Selecting model data and analysis results to plot "
· ``Contouring line-shaped elements with tick mark contour plots, '' Section 27.4.4
To learn how to customize the render style, translucency, or model edge characteristics of your contour
plot, see Chapter 37, "Customizing model display." For information on the computation of result
values, see ``Understanding how results are computed,'' Section 24.4.1.
5-844
Contouring analysis results
Banded-type contours are the default. You must choose line- or banded-type contours to produce a plot
of:
Figure 27-3 shows the appearance of line-, banded-, and quilt-type contour plots.
Figure 27-3 From left to right: line-, banded-, and quilt-type contours.
2. Click Line, Banded, or Quilt to choose the contour type you want.
5-845
Contouring analysis results
ABAQUS/CAE displays line-type contours as customized colored lines on the surface of your model.
You can stylize individual contour lines to make them easy to distinguish. This option is particularly
useful when colors are not available; for example, for black and white hardcopy plotting. Figure 27-4
shows a contour plot with customized contour lines.
You customize the colored lines one color (interval) at a time, referring to each interval by its position
in the contour legend. Interval number 1 is the first colored line starting from the bottom of the contour
plot legend. For information on the contour legend, see ``Customizing the legend,'' Section 38.1.
To stylize line-type contours:
2. To choose the interval you want to customize, click the Interval arrows until the desired interval
number appears in the Interval box.
Note: The Style and Thickness buttons change to show the current style and thickness of this interval, respectively. The
numbers above and below the Interval box change to correspond to the adjacent interval numbers. The area above and below
the Style and Thickness buttons changes to show the style and thickness, respectively, of these adjacent intervals.
5-846
Contouring analysis results
Figure 27-5 Banded-type contour plots with contour edges suppressed and displayed.
5-847
Contouring analysis results
a. Click the Color arrow to reveal the contour edge color options.
a. Click the Style button to reveal the contour edge style options.
a. Click the Thickness button to reveal the contour edge thickness options.
5-848
Contouring analysis results
specifications.
Your changes are saved for the duration of the session and will affect all subsequent plots in this
mode.
The normal lines, or tick mark axes, are drawn at nodes. At part boundaries, two tick mark axes are
drawn. Within a part, if the angle between two adjacent line elements is less than the specified feature
angle, a single tick mark axis is drawn in the direction of the average normal of elements sharing the
node. Otherwise, a tick mark axis is drawn normal to each element sharing the node. When averaging
normals, only displayed elements of the same type are considered in the calculation.
5-849
Contouring analysis results
2. To choose the normal direction in which the tick mark axes will be drawn on beam elements,
toggle the N1 or N2 button in the Orientation field.
Note: This option will be ignored when tick mark contour plots are displayed on line
elements other than beams. In this case, the tick mark axes are drawn in the element normal
direction.
5-850
Contouring analysis results
a. Click the Axis length button to reveal the length choices: Short, Medium, or Long.
a. Enter the desired base contour value in the Base Value field.
The value specified will be checked to determine whether it falls within the contour range.
If it is above the maximum contour value, the maximum contour value will be used as the
base value; if it is below the minimum contour value, the minimum contour value will be
used as the base value. By default, zero is used as the base value.
5-851
Contouring analysis results
· Select Auto-compute to request that ABAQUS compute the maximum contour value.
· Select Specify to specify the maximum value yourself; then enter the maximum value of your
choice in the Specify text field.
· Select Auto-compute to request that ABAQUS compute the minimum contour value.
· Select Specify to specify the minimum value yourself; then enter the minimum value of your
choice in the Specify text field.
5-852
Contouring analysis results
For line- or banded-type contours of element field output variables, you can control how
ABAQUS/CAE computes the contour limits. You can choose to compute the limits based on the
individual element extrapolated values or based on the values averaged at the nodes. Use extrapolated
values to accurately reflect extreme values that may otherwise be averaged out and to fix the range
regardless of changes in the results averaging threshold. The default is to compute the limits using
values averaged at the nodes. To learn how to control the results averaging threshold, see ``Controlling
result averaging,'' Section 24.4.4.
To control how ABAQUS computes contour limits:
· Click Use only extrapolated values to use only extrapolated (not averaged) values to
compute the contour limits.
· Click Use extrapolated, averaged values to use extrapolated averaged values to compute
the contour limits. In this case the limits may be affected by the results averaging threshold.
5-853
Contouring analysis results
you can choose the colors ABAQUS uses to represent values that exceed the limits you have specified.
By default, ABAQUS displays such values in shades of gray. For more information on limiting the
range of the plot, see ``Setting contour limits,'' Section 27.4.6.
To customize contour colors:
2. To choose the color of values within the limits of the plot, click the button under the spectrum type
you want.
3. To control the color of values that exceed the limits of the plot, do one of the following:
· Click Specify; then use the Greater than max and Less than min color menus to choose the
colors you want. (In the dialog box, the spectrum types change to display the colors you
select.)
Or,
· Click Use spectrum min/max to accept the minimum and maximum contour spectrum colors
for such values.
5-854
Contouring analysis results
banded-type contour plot with nine uniform contour intervals on the left and with continuous contours
on the right.
Figure 27-7 Contour plots showing uniform and continuous contour intervals.
The contour legend, if active, will include two more intervals than the number you choose.
ABAQUS/CAE adds intervals at the top and bottom of the legend to indicate any values that exceed
the contour plot limits. For more information on the contour legend, see ``Customizing the legend,''
Section 38.1.
To customize the contour intervals:
5-855
Contouring analysis results
5-856
Plotting analysis results as symbols
The relative sizes of the arrows indicate the magnitude of the result values. The directions of the
arrows indicate the global directions of the results. In tensor plots arrows with arrowheads pointing in
toward the arrow shaft represent compressive values; arrows with arrowheads pointing out from the
arrow shaft represent tensile values.
The symbol plot legend shows you how each arrow color corresponds to a specific variable or variable
component. To learn how to display the minimum and maximum values associated with your symbol
plot, see ``Customizing the legend,'' Section 38.1.
6-857
Plotting analysis results as symbols
By default, ABAQUS/CAE plots all of a variable's result values in a symbol plot. The maximum value
appears as the largest arrow in the plot, and all other arrows are scaled in proportion to that arrow size.
However, you can use the Symbol Plot Options dialog box to limit the range of values that appear in
a plot.
· When you specify a particular maximum value, only arrows representing absolute values less than
or equal to that maximum value appear in the plot.
The largest arrow in the plot will represent the largest absolute result value that is less than or
equal to the limit you specify. All other arrows in the plot will be scaled in proportion to that
arrow size.
· When you specify a particular minimum value, only arrows representing absolute values greater
than that minimum value appear in the plot.
· Color & Style: The Color & Style page contains the following tabs:
- General: Control the color, style, and thickness of model edges and the model fill color for
shaded plots.
- Vector: Choose to plot the resultant or a selected component of a vector variable, and
customize the arrow appearance.
- Tensor: Choose to plot all principal components or a selected component of a tensor variable,
and customize the arrow appearance.
· Labels: Control element, face, and node labels and node symbols.
- Vector: Choose to either specify the minimum and maximum vector values or to have
ABAQUS/CAE automatically compute these values.
- Tensor: Choose to either specify the minimum and maximum tensor values or to have
ABAQUS/CAE automatically compute these values.
6-858
Plotting analysis results as symbols
To learn how to customize the render style and other display characteristics of your symbol plot, see
Chapter 37, "Customizing model display." For more information on tensor and field output variables,
see ``Overview of field output variable selection, '' Section 24.3.1. For more information on selecting
the results step, see ``Selecting a specific results step and frame,'' Section 24.2.1.
4. For a symbol plot on the deformed shape, select the deformed field output variable to display.
5. Select the plot mode-independent and symbol plot customization options you want.
Tip: You can also produce a symbol plot using the tool in the toolbox.
The current viewport changes to display a customized symbol plot of the specified field output
variable at the specified step and frame of the current output database. ABAQUS is now in the
symbol plot mode.
6-859
Plotting analysis results as symbols
In this mode ABAQUS automatically refreshes your symbol plot each time you click Apply in the
step and frame selector dialog box or the plot mode-independent or symbol plot options dialog
boxes. The current viewport will remain in the symbol plot mode until you produce a plot in some
other (e.g., contour, deformed) mode.
To learn how to customize the render style and the underlying model attributes of your symbol plot,
see Chapter 37, "Customizing model display."
· Display arrows that represent resultant values of the variable. For example, a symbol plot of total
displacement appears on the left side of Figure 28-2.
· Display arrows that represent specific component values of the variable. For example, a symbol
plot of displacement in the 1-direction appears on the right side of Figure 28-2.
Figure 28-2 Symbol plots showing total displacement and displacement in the 1-direction.
6-860
Plotting analysis results as symbols
Likewise, when you display a tensor variable in a symbol plot, you can choose from the following
options:
· Display arrows that represent each of the principal components of the variable. For example, a
symbol plot of maximum, middle, and minimum principal stress appears on the left side of Figure
28-3.
· Display arrows that represent a specific principal component of the variable. For example, a
symbol plot of only maximum principal stress appears on the right side of Figure 28-3.
Figure 28-3 Symbol plot showing all three principal components (left), and symbol plot showing only
maximum principal stress (right).
By default, ABAQUS/CAE displays resultant values in vector variable symbol plots and all principal
components in tensor variable symbol plots. If you want to display a specific variable component, you
must specify options in both the Symbol Plot Options dialog box and the Field Output dialog box.
To plot a particular variable or variable component:
6-861
Plotting analysis results as symbols
· Click the Vector tab if you are creating a vector symbol plot.
· Click the Tensor tab if you are creating a tensor symbol plot.
2. Click the Quantity menu button, and select the option of your choice.
· Select Resultant to display arrows that represent the resultant of the variable.
· Select All Principal Components to display arrows that represent all three principal
components: maximum, middle, and minimum.
· Select Selected Principal Component to display only arrows that represent a particular
principal component.
4. Select the variable or variable component of your choice in the Field Output dialog box. For more
information, see ``Selecting the primary field output variable,'' Section 24.3.2.
· Click the Vector tab if you are creating a vector symbol plot.
· Click the Tensor tab if you are creating a tensor symbol plot.
2. Select the color or colors of your choice for the arrows in the plot.
6-862
Plotting analysis results as symbols
· If you are plotting all principal components, click the Maximim principal, Mid principal,
and Minimum principal menu buttons and select the colors in which you want each arrow
type to appear.
· If you are plotting only one principal component, click the arrow next to the Color text
field, and select the color in which you want the principal component arrows to appear.
3. Click the Max length menu button, and select the arrow length of your choice. The default
selection is Medium.
Your selection determines the size of the arrow representing the largest value in the plot. All other
arrows in the plot will be scaled to that size.
4. Click the Thickness menu button, and select the arrow shaft thickness of your choice.
5. Click the Arrowhead menu button, and select the arrowhead design of your choice.
6-863
Plotting analysis results as symbols
2. In the area labeled Max in the top half of the page, choose one of the following options:
· Select Auto-compute to use the largest result value as the maximum value.
· Select Specify to specify the maximum value yourself; then enter the maximum value of your
choice in the Specify text field.
3. In the area labeled Min in the bottom half of the page, choose one of the following options:
· Select Auto-compute to use the smallest result value as the minimum value.
· Select Specify to specify the minimum value yourself; then enter the minimum value of your
choice in the Specify text field.
6-864
Plotting material orientations
Material orientations are available only for those elements for which field output is requested at the
selected section points, with the exception of during the initial step when material orientations are
available for all valid elements at all section points. Valid elements include all shell elements, as well
as solid elements for which you have defined a local orientation. The material orientations are
displayed at the current step and frame of the analysis and at the current section point selection for
shell elements.
7-865
Plotting material orientations
· Color & Style: The Color & Style page contains the following tabs:
- General: Control the color, style, and thickness of model edges and the model fill color for
shaded plots.
- Triad: Control the visibility, color, length, thickness, and arrow appearance of the material
orientation triad axes.
· Labels: Control element, face, and node labels and node symbols.
· Shape: Choose to display material orientation triads on the undeformed or the deformed shape.
To learn how to customize the render style and other display characteristics of your material
orientation plot, see Chapter 37, "Customizing model display." For more information on selecting the
results step, see ``Selecting a specific results step and frame,'' Section 24.2.1. For more information on
selecting section point locations, see ``Selecting field output section points, '' Section 35.3.3.
7-866
Plotting material orientations
4. Select the plot mode-independent and material orientation plot customization options you want.
Tip: You can also produce a material orientation plot using the tool in the toolbox.
The current viewport changes to display a customized material orientation plot. ABAQUS is now
in the material orientation plot mode.
In this mode ABAQUS automatically refreshes your material orientation plot each time you click
Apply in the step and frame selector dialog box, the section point selector dialog box, or the plot
mode-independent or material orientation plot options dialog boxes. The current viewport will
remain in the material orientation plot mode until you produce a plot in some other (e.g., contour,
deformed) mode.
To learn how to customize the render style and the underlying model attributes of your material
orientation plot, see Chapter 37, "Customizing model display."
7-867
Plotting material orientations
From the main menu bar, select Options->Material Orientation; then click the Color & Style tab
in the dialog box that appears. Click Triad.
The triad options appear.
2. Toggle on the buttons to the left of each of the axes to display or suppress them.
3. Select the color or colors of your choice for the visible triad axes in the plot.
4. Click the Length menu button, and select the axis length of your choice. The default selection is
Medium.
5. Click the Thickness menu button, and select the axis thickness of your choice.
6. Click the Arrowhead menu button, and select the arrowhead design of your choice.
7-868
X-Y plotting
· ``What is an X-Y data object, and what is an X-Y plot?,'' Section 30.1.1
· ``Understanding "Temp" and other X-Y data object names,'' Section 30.1.3
8-869
X-Y plotting
8-870
X-Y plotting
elements or nodes to read the data, from which steps of the analysis to read, and the frequency
at which to read the data; for example, you can read every third data point. For more
information, see ``Reading X-Y data from output database field output, '' Section 30.2.2.
ASCII file
Select this method to read X- and Y-values from an existing text file. The file can contain more
than two columns of data, separated by commas, spaces, or tabs; and you can specify which
columns correspond to the X- and Y-axis data. In addition, you can specify the frequency at
which the data should be read from the file; for example, every third row. For more
information, see ``Reading X-Y data from an ASCII file,'' Section 30.2.3.
Keyboard
Select this method to manually type X- and Y-values into a simple table editor. Within this
method, ABAQUS supports several special editing techniques, as well as an option to read
data from a file. For more information on this topic, see ``Entering X-Y data from the
keyboard,'' Section 30.2.4.
Path
Select this method to specify an X-Y data object by reading field output results at locations
along a path through your model. ABAQUS obtains results from an output database. You can
specify the points that make up the path and the step, frame, and variable for which to obtain
results. For more information, see Chapter 32, "Viewing results along a path."
In addition, you can create an X-Y data object while using the table editor to create a material in the
Property module. For more information, see ``Entering tabular data,'' Section 6.3.5.
Once you have specified your X-Y data object, you can save it or you can display it in the form of an
X-Y plot. Saving the X-Y data object allows you to subsequently plot, edit, rename, delete, or operate
on it. For X-Y data originating from sources other than output database history output, you must save
your data to later produce an X-Y plot containing multiple data objects. Saved X-Y data objects are
retained only for the duration of the session.
8-871
X-Y plotting
· When you plot X-Y data, the X-Y plot legend identifies by name all X-Y data objects appearing in
the plot.
· When you select Tools->XY Data from the main menu bar, the Manager, Edit, Copy, Rename,
Delete, and Plot tools list all X-Y data objects created during the session by name.
· When you customize the appearance of the curve representing an X-Y data object, you first select
the X-Y data object by name from those listed in the XY Curve Options dialog box.
In most cases ABAQUS/CAE is able to provide a meaningful default name for your X-Y data object.
As you save your X-Y data object, ABAQUS/CAE shows you the default name and gives you an
opportunity to override this default with the name of your choice. Once saved, you can provide a new
name for your X-Y data object at any time by renaming it. For information on renaming, see
``Managing objects using manager dialog boxes,'' Section 6.5.6.
There are three basic forms of X-Y data object names, as follows:
Temp-n
If you produce an X-Y plot by clicking Plot from any of the following dialog boxes:
ABAQUS/CAE names your X-Y data according to the pattern Temp-1, Temp-2, etc. This
name indicates that the plot represents the data configured in the dialog box, which is
considered temporary data whether or not you have clicked Save As to save it.
Conversely, if Temp-n appears in your plot legend, you are plotting temporary data. You
cannot edit, copy, rename, delete, operate on, or produce a report of temporary data. To
accomplish any of these tasks, you must first save your data. You can select curve style
preferences for temporary data, but the curve styles will revert to the defaults if you replot the
data without having saved it. To learn how to save your data, see ``Saving an X-Y data
object,'' Section 30.2.5.
XYData-n
If you create a new X-Y data object using the Save As button provided in the XY Data from
ASCII File or XY Data from Keyboard dialog boxes, ABAQUS/CAE suggests a default name
for your X-Y data according to the pattern XYData-1, XYData-2, etc. To establish a more
meaningful name, you can use the Save XYData As dialog box to overwrite this default with
the name of your choice.
To locate the XY Data from ASCII File or XY Data from Keyboard dialog boxes, select
Tools->XY Data->Create from the main menu bar; then click the choice of interest in the
dialog box that appears, and click Continue.
8-872
X-Y plotting
Meaningful names
You can establish a meaningful name (a name of your choice) for your X-Y data object either
by specifying a name as you save your data or by subsequently renaming it. As you save your
data, ABAQUS/CAE displays the default name in the Save XYData As dialog box; you can
overwrite this default. ABAQUS/CAE generates meaningful default names for X-Y data
created from the ODB History Output or XY Data from ODB Field Output dialog boxes.
To display the name of your choice in your X-Y plot legend, you must produce the plot by
selecting named data objects and then clicking Plot. To do so, select Tools->XY
Data->Manager from the main menu bar. For more information, see ``Producing an X-Y
plot,'' Section 30.3.
· ``Reading X-Y data from output database history output,'' Section 30.2.1
· ``Reading X-Y data from output database field output, '' Section 30.2.2
For information on specifying X-Y data objects by obtaining field output results along a path through
your model, see Chapter 32, "Viewing results along a path;" for information on specifying X-Y data
objects by operating on existing X-Y data, see ``Operating on saved X-Y data objects,'' Section 30.4.
ABAQUS/CAE then reads X-Y data pairs from the output database at the frames you specify. If you
select multiple variables, ABAQUS/CAE reads the data pairs and creates a separate X-Y data object for
each variable. For time-based analyses, X-values are taken as total time from the start of the analysis
or, in the case of a restarted analysis, as total time from the start of the last continuation of the analysis.
Y-values are taken as the value at that time of the variable at the location you specify.
8-873
X-Y plotting
2. In the Output Variables field, click one or more variables that you want to read. Variables are
listed alphabetically along with their locations. The default is to read the first entry in the list. For
more information on selecting multiple items in dialog boxes, see ``Selecting multiple items in
lists,'' Section 6.3.8.
The specified variable and location are highlighted.
3. In the Steps field, click the step or steps you want to read. The default is to read data from all
available steps.
The specified steps are highlighted.
· Skip, then enter the number of frames to skip in the frames between reads box. For
example, if you enter 1, every second frame is read.
7. When you have finished, click Dismiss to close the dialog box.
8-874
X-Y plotting
· ``Understanding "Temp" and other X-Y data object names,'' Section 30.1.3
ABAQUS/CAE then reads X-Y data pairs from the output database at the frames you specify. If you
select multiple variables or multiple locations, ABAQUS/CAE reads the data pairs and creates a
separate X-Y data object for each variable/location pair. For all time-based analyses, X-values are taken
as total time from the start of the analysis. Y-values are taken as the corresponding values of the
variable at the specified location.
To read X-Y data from output database field output:
2. Click the Position arrow to reveal possible positions at which to list variables for your selection;
then choose the desired position.
The list of variables is refreshed to show only those that can be read at the selected position.
3. Select the field output variables to be read using either the check box next to each variable in the
list (this method is the default) or the Edit text field at the bottom of the page.
2. To select a variable and all of its components, click that variable's check box.
3. To choose among the individual components of a variable, click the arrow next to that
variable's check box to list its components; then click individual component check boxes
8-875
X-Y plotting
to select them.
2. In the Edit text field, enter the names of the variables and components to be read. To be
valid, a variable must be available on the output database for the current position.
5. From the ODB Item list at the top left of the dialog box, select either Elements or Nodes.
ABAQUS refreshes the Selection Method list at the bottom of the dialog box and the item list at
the right.
6. Select the specific elements or nodes for which to read output data.
· Pick from viewport to specify elements or nodes by picking them directly from the
viewport.
The Selection field appears with the text (None) to indicate that no elements or nodes
have been picked.
· To specify element or node sets, select one or more set names from the item list. (For
more information, see ``Selecting multiple items in lists,'' Section 6.3.8.) If your
output database contains many sets, you can use the filter to reduce the number of set
names displayed. Click the Tip button next to the Filter field to see examples of valid
filtering syntax. Verify your selection by toggling Highlight items in viewport.
· To specify elements or nodes by picking them directly from the viewport, click Edit
Selection. Select elements for display group or Select nodes for display group
appears in the prompt area.
8-876
X-Y plotting
Select one or more elements or nodes from the viewport (for more information see
Chapter 9, "Selecting objects within the viewport"). The elements or nodes are
highlighted in the viewport.
Click Done in the prompt area when you have finished. The text next to Selection in
the XY Data from ODB Field Output dialog box changes to (Picked) to indicate that
you have selected elements or nodes.
· To specify element or node labels, first select the name of the part instance for which
you are obtaining results from the list in the Part instance field. Type into the Labels
field a list of element or node numbers separated by commas or a range of numbers
such as 1:4. Verify your selection by clicking Highlight Items in Viewport .
The following table summarizes the restrictions that exist on the availability of element or node
data for the output position specified on the Variables page:
Output position Available for
Integration point Elements
Centroid Elements
Element nodal Elements or nodes
Unique nodal Nodes
8. In the Steps field, select the step or steps you want to read. The default is to read data from all
available steps.
The specified steps are highlighted.
· Skip, then enter the number of frames to skip in the frames between reads box. For
example, if you enter 1, every second frame is read.
11. To save the data you have configured, click Save As.
Note: To plot your saved X-Y data, select Tools->XY Data->Plot from the main menu bar and choose the X-Y data from the
pull-right menu.
12. When you have finished, click Dismiss to close the dialog box.
8-877
X-Y plotting
· ``Understanding "Temp" and other X-Y data object names,'' Section 30.1.3
2. Enter the name of your ASCII file in one of the following ways:
· Type the name into the File window at the top of the dialog box, or
3. Specify which columns of the file to read. Columns can be separated by spaces, tabs, or a comma.
a. To specify the column within the file to read as X-values, enter an integer in the Read X
values from field box. The default is field 1, the first column.
b. To specify the column within the file to read as Y-values, enter an integer in the Read Y
values from field box. The default is field 2, the second column.
4. Specify which rows of the file to read; the default is all rows.
8-878
X-Y plotting
· Click Skip; then enter the number of file rows to skip in the rows between reads box. A
value of 0 means read all rows; a value of 1 means read every other row. Reading always
begins with the first row.
7. When you have finished, click Dismiss to close the dialog box.
· ``Understanding "Temp" and other X-Y data object names,'' Section 30.1.3
2. Use standard keyboard and mouse editing techniques to insert, modify, or delete X- and Y-values
in the XY Data from Keyboard table. For special table editing options or to read data from an
ASCII file, press mouse button 3. (For more information, see ``Entering tabular data,'' Section
6.3.5.)
8-879
X-Y plotting
An X-Y plot appears in the current viewport. The plot represents the data you have configured in
the dialog box, which ABAQUS considers temporary data whether or not you have clicked Save
As to save it.
5. When you have finished, click Cancel to close the dialog box.
· ``Understanding "Temp" and other X-Y data object names,'' Section 30.1.3
· Produce an X-Y plot containing multiple X-Y data objects from any source other than history
output.
Saved data persist for the duration of the session. To save your X-Y data object beyond the duration of
the session, you must write the data to a file. For information on writing X-Y data to a file, see Chapter
35, "Generating tabular data reports."
To save an X-Y data object:
8-880
X-Y plotting
b. Choose the source of your data from the list, and click Continue.
ABAQUS displays the appropriate dialog box.
To produce an X-Y plot of output database results along a path through your model:
To specify a path through your model, select Tools->Path->Create from the main menu bar;
then configure the dialog boxes that appear. For more information, see ``Creating a path
through your model,'' Section 32.2.
After you have created the path, select Tools->XY Data->Create from the main menu bar.
8-881
X-Y plotting
Choose Path as the source of the X-Y data object, then click Continue. Configure the dialog
box that appears, then click Plot. For more information, see ``Obtaining X-Y data along a
path,'' Section 32.3.
· To display a single X-Y data object, select Tools->XY Data->Plot from the main menu bar;
and select the X-Y data object from the pull-right menu.
· To display multiple X-Y data objects on a single X-Y plot, select Tools->XY Data->Manager
from the main menu bar. Select the X-Y data objects from the dialog box that appears; then
click Plot.
· ``Understanding "Temp" and other X-Y data object names,'' Section 30.1.3
8-882
X-Y plotting
Parentheses can also be used to control mathematical evaluation or for visual clarity. ABAQUS/CAE
notifies you if your expression contains invalid syntax or cannot be evaluated for mathematical
reasons; for example, if evaluation would require dividing by zero.
· If the missing X-coordinate lies within the minimum and maximum available X-coordinates for the
data object, a new Y-coordinate value is computed by linear interpolation.
· If the missing X-coordinate lies beyond the minimum or maximum available X-coordinates for the
data object, a new Y-coordinate value is computed by assuming the Y-coordinate value remains
constant beyond these extreme points.
These additional data points exist only to carry out the operation and are not saved as part of the input
argument data objects.
8-883
X-Y plotting
a. Click on data object names and built-in functions in the dialog box to select them.
Use drag-select for multiple contiguous data object name selection.
Commas are inserted automatically between the data object names.
b. Use standard mouse and keyboard editing techniques to position the cursor and configure
your expression.
c. Adjust the syntax of your expression if necessary: data object names must be surrounded
by quotation marks, commas must separate function arguments, and parentheses may be
needed.
5. To plot your new, saved X-Y data object, select Tools->XY Data->Plot from the main menu bar
and select the X-Y data object from the pull-right menu.
7. When you are done, click Dismiss to close the dialog box.
8-884
X-Y plotting
The following list indicates the section where you can find more information for each X-Y data
operation.
Mathematical operations:
+ ``Using addition on X-Y data objects,'' Section 30.4.5
- ``Using negation or subtraction on X-Y data objects,''
Section 30.4.6
* ``Using multiplication on X-Y data objects,'' Section
30.4.7
/ ``Using division on X-Y data objects,'' Section 30.4.8
1/A ``Using division on X-Y data objects,'' Section 30.4.8
abs(A) ``Taking the absolute value of an X-Y data object,''
Section 30.4.9
avg(X,X,...) ``Finding the average of two or more X-Y data objects,''
Section 30.4.10
currentAvg(X) ``Finding the current average of an X-Y data object,''
Section 30.4.11
differentiate(X) ``Differentiating an X-Y data object,'' Section 30.4.12
integrate(X) ``Integrating an X-Y data object,'' Section 30.4.13
normalize(X) ``Normalizing an X-Y data object,'' Section 30.4.14
sqrt(A) ``Taking the square root of an X-Y data object,'' Section
30.4.15
srss(X,X,...) ``Taking the square root of the sum of the squares of two
or more X-Y data objects,'' Section 30.4.16
sum(A,A,...) ``Summing two or more X-Y data objects,'' Section
30.4.17
vectorMagnitude(X,X, ``Calculating vector magnitudes,'' Section 30.4.18
8-885
X-Y plotting
X)
Trigonometric operations:
For more information, see ``Applying trigonometric functions to an X-Y data object,'' Section
30.4.19.
cos(A) Take the cosine of an X-Y data object.
acos(A) Take the arccosine of an X-Y data object.
cosh(A) Take the hyperbolic cosine of an X-Y data object.
sin(A) Take the sine of an X-Y data object.
asin(A) Take the arcsine of an X-Y data object.
sinh(A) Take the hyperbolic sine of an X-Y data object.
tan(A) Take the tangent of an X-Y data object.
atan(A) Take the arctangent of an X-Y data object.
tanh(A) Take the hyperbolic tangent of an X-Y data object.
Other operations:
append(X,X,...) ``Appending two or more X-Y data objects,''
Section 30.4.32
combine(X,X) ``Combining two X-Y data objects,'' Section
8-886
X-Y plotting
30.4.33
degreeToRadian(A) ``Converting the angular units used for X-Y
data objects,'' Section 30.4.34
radianToDegree(A) ``Converting the angular units used for X-Y
data objects,'' Section 30.4.34
swap(X) ``Swapping the order of an X-Y data object,''
Section 30.4.35
then
and
8-887
X-Y plotting
For alignment, ABAQUS/CAE computes the values of the first and second data objects as:
XYData1 extrapolated = [(1; 1); (2; 2); (3; 3); (4; 3); (5; 3)];
and
XYData2 extrapolated = [(1; 4); (2; 4); (3; 4); (4; 4); (5; 5)];
then
(XYData1 + XYData2) = [(1; 5); (2; 6); (3; 7); (4; 7); (5; 8)]:
Note: This application of the + symbol has the same behavior as the sum function.
2. From the XY Data choices, click the name of the X-Y data object on which to operate. You can
choose from all X-Y data objects previously saved within this session (listed alphabetically in the
XY Data field).
The X-Y data object name appears within the expression window.
8-888
X-Y plotting
· Use your mouse and keyboard to enter a scalar as the second argument of the + operator in the
expression window, or
· From the XY Data choices, click the name of a data object argument for the + operator in the
expression window.
5. To continue to build your expression, position the cursor in the expression window and type in or
select the functions, operators, and X-Y data you want to include.
7. To save your new X-Y data object, click Save As and then provide a name in the dialog box that
appears.
Saving your data object makes it available for future operations within this session and for
inclusion in X-Y plots containing multiple data objects.
8. When you are finished, click Dismiss to close the dialog box.
8-889
X-Y plotting
X-Y data object. ABAQUS/CAE computes the new Y-coordinates as the scalar subtracted from
each original Y-coordinate. For example, if
then
then
To subtract one X-Y data object from another X-Y data object:
This method yields a new X-Y data object having as its X-coordinates all X-coordinates of the
first data object and any additional X-coordinates needed for alignment of the two objects.
ABAQUS/CAE computes additional X-Y data pairs by interpolation and extrapolation . The
new data object has as its Y-coordinates the Y-coordinates of the second data object subtracted
from the Y-coordinates of the first data object. For example, let
and
For alignment, ABAQUS/CAE computes the values of the first and second data objects as:
XYData1 extrapolated = [(1; 4); (2; 4); (3; 4); (4; 4); (5; 5)]
and
XYData2 extrapolated = [(1; 1); (2; 2); (3; 3); (4; 3); (5; 3)];
then
8-890
X-Y plotting
(XYData1 ¡ XYData2) = [(1; 3); (2; 2); (3; 1); (4; 1); (5; 2)]:
3. Use your mouse and keyboard to position the cursor in the expression window; then specify the
necessary arguments. Available X-Y data objects include all those previously saved within this
session (listed alphabetically in the XY Data field).
To use negation
From the XY Data choices, click the name of the X-Y data object to negate.
To use subtraction
· From the XY Data choices, click the name of the X-Y data object on which to operate.
4. To continue to build your expression, position the cursor in the expression window and type in or
select the functions, operators, and X-Y data you want to include.
8-891
X-Y plotting
6. To save your new X-Y data object, click Save As and then provide a name in the dialog box that
appears.
Saving your data object makes it available for future operations within this session and for
inclusion in X-Y plots containing multiple data objects.
7. When you are finished, click Dismiss to close the dialog box.
then
8-892
X-Y plotting
and
For alignment, ABAQUS/CAE computes the values of the first and second data objects as:
XYData1 extrapolated = [(1; 1); (2; 2); (3; 3); (4; 3); (5; 3)]
and
XYData2 extrapolated = [(1; 4); (2; 4); (3; 4); (4; 4); (5; 5)];
then
(XYData1 * XYData2) = [(1; 4); (2; 8); (3; 12); (4; 12); (5; 15)]:
2. From the XY Data choices, click the name of the X-Y data object on which to operate. You can
choose from all X-Y data objects previously saved within this session (listed alphabetically in the
XY Data field).
8-893
X-Y plotting
The X-Y data object name appears within the expression window.
· Use your mouse and keyboard to enter a scalar as the second argument of the * operator in the
expression window, or
· From the XY Data choices, click the name of a data object argument for the * operator in the
expression window.
5. To continue to build your expression, position the cursor in the expression window and type in or
select the functions, operators, and X-Y data you want to include.
7. To save your new X-Y data object, click Save As and then provide a name in the dialog box that
appears.
Saving your data object makes it available for future operations within this session and for
inclusion in X-Y plots containing multiple data objects.
8. When you are finished, click Dismiss to close the dialog box.
8-894
X-Y plotting
then
Note: As a convenience, the Operate on XY Data dialog box offers an inverse function, 1/A.
then
and
For alignment, ABAQUS/CAE computes the values of the first and second data objects as:
XYData1 extrapolated = [(1; 4); (2; 4); (3; 4); (4; 4); (5; 5)]
and
XYData2 extrapolated = [(1; 1); (2; 2); (3; 3); (4; 3); (5; 3)];
then
(XYData1 / XYData2) = [(1; 4); (2; 2); (3; 1:33); (4; 1:33); (5; 1:66)]:
8-895
X-Y plotting
3. To specify each of the two arguments for the / operator, use your mouse and keyboard to position
the cursor in the expression window; then do one of the following:
· From the XY Data choices, click the name of the X-Y data object on which to operate. You can
choose from all X-Y data objects previously saved within this session (listed alphabetically in
the XY Data field).
4. To continue to build your expression, position the cursor in the expression window and type in or
select the functions, operators, and X-Y data you want to include.
6. To save your new X-Y data object, click Save As and then provide a name in the dialog box that
appears.
Saving your data object makes it available for future operations within this session and for
8-896
X-Y plotting
7. When you are finished, click Dismiss to close the dialog box.
3. From the XY Data choices, click the name of the X-Y data object on which to operate. You can
8-897
X-Y plotting
choose from all X-Y data objects previously saved within this session (listed alphabetically in the
XY Data field).
The X-Y data object name appears within the abs function parentheses in the expression window.
4. To continue to build your expression, position the cursor in the expression window and type in or
select the functions, operators, and X-Y data you want to include.
6. To save your new X-Y data object, click Save As and then provide a name in the dialog box that
appears.
Saving your data object makes it available for future operations within this session and for
inclusion in X-Y plots containing multiple data objects.
7. When you are finished, click Dismiss to close the dialog box.
8-898
X-Y plotting
For information on how to find the current average of a single X-Y data object, see ``Finding the
current average of an X-Y data object,'' Section 30.4.11.
To find the average of two or more X-Y data objects:
3. From the XY Data choices, click the names of two or more X-Y data objects on which to operate.
You can choose from all X-Y data objects previously saved within this session (listed
alphabetically in the XY Data field).
The X-Y data object names appear, separated by commas, within the avg function parentheses in
the expression window.
4. To continue to build your expression, position the cursor in the expression window and type in or
select the functions, operators, and X-Y data you want to include.
6. To save your new X-Y data object, click Save As and then provide a name in the dialog box that
appears.
Saving your data object makes it available for future operations within this session and for
inclusion in X-Y plots containing multiple data objects.
7. When you are finished, click Dismiss to close the dialog box.
8-899
X-Y plotting
Note: The last value of the new X-Y data object represents the overall average Y-coordinate of the
original X-Y data object.
For information on how to find the current average of two or more X-Y data objects, see ``Finding the
average of two or more X-Y data objects,'' Section 30.4.10.
To find the current average of an X-Y data object:
3. From the XY Data choices, click the name of the X-Y data object on which to operate. You can
8-900
X-Y plotting
choose from all X-Y data objects previously saved within this session (listed alphabetically in the
XY Data field).
The X-Y data object name appears within the currentAvg function parentheses in the expression
window.
4. To continue to build your expression, position the cursor in the expression window and type in or
select the functions, operators, and X-Y data you want to include.
6. To save your new X-Y data object, click Save As and then provide a name in the dialog box that
appears.
Saving your data object makes it available for future operations within this session and for
inclusion in X-Y plots containing multiple data objects.
7. When you are finished, click Dismiss to close the dialog box.
· ``Finding the average of two or more X-Y data objects,'' Section 30.4.10
8-901
X-Y plotting
3. From the XY Data choices, click the name of the X-Y data object on which to operate. You can
choose from all X-Y data objects previously saved within this session (listed alphabetically in the
XY Data field).
The X-Y data object name appears within the differentiate function parentheses in the expression
window.
4. To continue to build your expression, position the cursor in the expression window and type in or
select the functions, operators, and X-Y data you want to include.
6. To save your new X-Y data object, click Save As and then provide a name in the dialog box that
appears.
Saving your data object makes it available for future operations within this session and for
inclusion in X-Y plots containing multiple data objects.
7. When you are finished, click Dismiss to close the dialog box.
8-902
X-Y plotting
3. From the XY Data choices, click the name of the X-Y data object on which to operate. You can
choose from all X-Y data objects previously saved within this session (listed alphabetically in the
XY Data field).
The X-Y data object name appears within the integrate function parentheses in the expression
window.
4. To continue to build your expression, position the cursor in the expression window and type in or
select the functions, operators, and X-Y data you want to include.
8-903
X-Y plotting
6. To save your new X-Y data object, click Save As and then provide a name in the dialog box that
appears.
Saving your data object makes it available for future operations within this session and for
inclusion in X-Y plots containing multiple data objects.
7. When you are finished, click Dismiss to close the dialog box.
8-904
X-Y plotting
3. From the XY Data choices, click the name of the X-Y data object on which to operate. You can
choose from all X-Y data objects previously saved within this session (listed alphabetically in the
XY Data field).
The X-Y data object name appears within the normalize function parentheses in the expression
window.
4. To continue to build your expression, position the cursor in the expression window and type in or
select the functions, operators, and X-Y data you want to include.
6. To save your new X-Y data object, click Save As and then provide a name in the dialog box that
appears.
Saving your data object makes it available for future operations within this session and for
inclusion in X-Y plots containing multiple data objects.
7. When you are finished, click Dismiss to close the dialog box.
· ``Taking the square root of the sum of the squares of two or more X-Y data objects,'' Section
30.4.16
8-905
X-Y plotting
3. From the XY Data choices, click the name of the X-Y data object on which to operate. You can
choose from all X-Y data objects previously saved within this session (listed alphabetically in the
XY Data field).
The X-Y data object name appears within the sqrt function parentheses in the expression window.
4. To continue to build your expression, position the cursor in the expression window and type in or
select the functions, operators, and X-Y data you want to include.
6. To save your new X-Y data object, click Save As and then provide a name in the dialog box that
appears.
Saving your data object makes it available for future operations within this session and for
inclusion in X-Y plots containing multiple data objects.
7. When you are finished, click Dismiss to close the dialog box.
· ``Taking the square root of the sum of the squares of two or more X-Y data objects,'' Section
8-906
X-Y plotting
30.4.16
30.4.16 Taking the square root of the sum of the squares of two
or more X-Y data objects
Use the srss function to perform a square root of the sum of the squares operation on two or more
previously saved X-Y data objects (each object is a collection of ordered pairs) to produce a new X-Y
data object. Use this function, for example, to find the total magnitude of two or more X-Y data objects
at matching X-coordinates.
The new X-Y data object has as its X-coordinates all X-coordinates of the first data object and any
additional X-coordinates needed for alignment of the remaining objects. ABAQUS/CAE computes
additional X-Y data pairs by interpolation and extrapolation . The new data object has as its
Y-coordinates the square root of the sum of the squares of all input X-Y data object Y-coordinates at
matching X-coordinates. The arguments to this function are commutative.
Figure 30-13 illustrates the type of X-Y plot that can be produced using the srss function.
To square the sum of the squares of two or more X-Y data objects:
8-907
X-Y plotting
3. From the XY Data choices, click the names of two or more X-Y data objects on which to operate.
You can choose from all X-Y data objects previously saved within this session (listed
alphabetically in the XY Data field).
The X-Y data object names appear, separated by commas, within the srss function parentheses in
the expression window.
4. To continue to build your expression, position the cursor in the expression window and type in or
select the functions, operators, and X-Y data you want to include.
6. To save your new X-Y data object, click Save As and then provide a name in the dialog box that
appears.
Saving your data object makes it available for future operations within this session and for
inclusion in X-Y plots containing multiple data objects.
7. When you are finished, click Dismiss to close the dialog box.
8-908
X-Y plotting
3. From the XY Data choices, click the names of two or more X-Y data objects to sum together. You
can choose from all X-Y data objects previously saved within this session (listed alphabetically in
the XY Data field).
The X-Y data object names appear, separated by commas, within the sum function parentheses in
the expression window.
4. To continue to build your expression, position the cursor in the expression window and type in or
select the functions, operators, and X-Y data you want to include.
6. To save your new X-Y data object, click Save As and then provide a name in the dialog box that
appears.
Saving your data object makes it available for future operations within this session and for
inclusion in X-Y plots containing multiple data objects.
7. When you are finished, click Dismiss to close the dialog box.
8-909
X-Y plotting
3. From the XY Data choices, click the names of three X-Y data objects on which to operate. You can
choose from all X-Y data objects previously saved within this session (listed alphabetically in the
XY Data field).
The X-Y data object names appear, separated by commas, within the vectorMagnitude function
parentheses in the expression window.
4. To continue to build your expression, position the cursor in the expression window and type in or
select the functions, operators, and X-Y data you want to include.
8-910
X-Y plotting
6. To save your new X-Y data object, click Save As and then provide a name in the dialog box that
appears.
Saving your data object makes it available for future operations within this session and for
inclusion in X-Y plots containing multiple data objects.
7. When you are finished, click Dismiss to close the dialog box.
then
8-911
X-Y plotting
2. From the Operators listed, click one of the following trigonometric functions:
sin(A) To compute the sine of your X-Y data object.
sinh(A) To compute the hyperbolic sine of your X-Y data
object.
asin(A) To compute the arcsine of your X-Y data object. Your
Y-data values must be in the range [-1, 1].
cos(A) To compute the cosine of your X-Y data object.
cosh(A) To compute the hyperbolic cosine of your X-Y data
object.
acos(A) To compute the arccosine of your X-Y data object.
Your Y-data values must be in the range [-1, 1].
tan(A) To compute the tangent of your X-Y data object.
tanh(A) To compute the hyperbolic tangent of your X-Y data
object.
atan(A) To compute the arctangent of your X-Y data object.
The trigonometric function you choose appears in the expression window.
3. From the XY Data choices, click the name of the X-Y data object on which to operate. You can
choose from all X-Y data objects previously saved within this session (listed alphabetically in the
XY Data field).
The X-Y data object name appears within the trigonometric function parentheses in the expression
window.
4. To continue to build your expression, position the cursor in the expression window and type in or
select the functions, operators, and X-Y data you want to include.
8-912
X-Y plotting
6. To save your new X-Y data object, click Save As and then provide a name in the dialog box that
appears.
Saving your data object makes it available for future operations within this session and for
inclusion in X-Y plots containing multiple data objects.
7. When you are finished, click Dismiss to close the dialog box.
· ``Converting the angular units used for X-Y data objects,'' Section 30.4.34
8-913
X-Y plotting
From the main menu bar, select Tools->XY data->Create. Click Operate on XY data in the
dialog box that appears; then click Continue. The Operate on XY Data dialog box appears.
3. From the XY Data choices, click the name of the X-Y data object on which to operate. You can
choose from all X-Y data objects previously saved within this session (listed alphabetically in the
XY Data field).
The X-Y data object name appears within the exp function parentheses in the expression window.
4. To continue to build your expression, position the cursor in the expression window and type in or
select the functions, operators, and X-Y data you want to include.
6. To save your new X-Y data object, click Save As and then provide a name in the dialog box that
appears.
Saving your data object makes it available for future operations within this session and for
inclusion in X-Y plots containing multiple data objects.
7. When you are finished, click Dismiss to close the dialog box.
then
8-914
X-Y plotting
2. From the Operators listed, click either log(A) or log10(A) to apply the natural log or base 10 log
function, respectively.
The logarithmic function you choose appears in the expression window.
3. From the XY Data choices, click the name of the X-Y data object on which to operate. You can
choose from all X-Y data objects previously saved within this session (listed alphabetically in the
XY Data field).
The X-Y data object name appears within the logarithmic function parentheses in the expression
window.
4. To continue to build your expression, position the cursor in the expression window and type in or
select the functions, operators, and X-Y data you want to include.
6. To save your new X-Y data object, click Save As and then provide a name in the dialog box that
appears.
Saving your data object makes it available for future operations within this session and for
inclusion in X-Y plots containing multiple data objects.
7. When you are finished, click Dismiss to close the dialog box.
8-915
X-Y plotting
To raise a scalar to an X-Y data object: power (scalar, data object name).
This method yields a new X-Y data object having the same X-coordinate values as the original
X-Y data object. ABAQUS/CAE computes the new Y-coordinates as the scalar raised to the
power of each original Y-coordinate. For example, if
then
To raise an X-Y data object to a scalar: power (data object name, scalar).
This method yields a new X-Y data object having the same X-coordinate values as the original
X-Y data object. ABAQUS/CAE computes the new Y-coordinates as each original
Y-coordinate raised to the scalar. For example, if
then
To raise an X-Y data object to another X-Y data object: power (data object name, data object
name).
This method yields a new X-Y data object having as its X-coordinates all X-coordinates of the
first data object and any additional X-coordinates needed for alignment of the two objects.
ABAQUS/CAE computes additional X-Y data pairs by interpolation and extrapolation . The
new data object has as its Y-coordinates the Y-coordinates of the first data object raised to the
Y-coordinates of the second data object. For example, let
8-916
X-Y plotting
and
For alignment, ABAQUS/CAE computes the values of the first and second data objects as:
XYData1 extrapolated = [(0; 1); (1; 1); (2; 2); (3; 2); (4; 2); (5; 1)];
and
XYData2 extrapolated = [(0; 1); (1; 1:33); (2; 1:66); (3; 2); (4; 4); (5; 6)];
then
power(XYData1, XYData2) = [(0; 1); (1; 1); (2; 3:17); (3; 4); (4; 16); (5; 1)]:
Figure 30-18 X-Y plot of one data object raised to another data object.
8-917
X-Y plotting
3. From the XY Data choices, click the name of the X-Y data object on which to operate. You can
choose from all X-Y data objects previously saved within this session (listed alphabetically in the
XY Data field).
The X-Y data object name appears within the power function parentheses in the expression
window.
· Use your mouse and keyboard to enter a scalar as either the first or second argument of the
power function in the expression window, depending on the operation you want to perform,
and to separate the two arguments with a comma, or
· From the XY Data choices, click the name of a data object argument for the power function in
the expression window.
5. To continue to build your expression, position the cursor in the expression window and type in or
select the functions, operators, and X-Y data you want to include.
7. To save your new X-Y data object, click Save As and then provide a name in the dialog box that
appears.
Saving your data object makes it available for future operations within this session and for
inclusion in X-Y plots containing multiple data objects.
8. When you are finished, click Dismiss to close the dialog box.
8-918
X-Y plotting
Possible SAE class values are 60, 100, 180, and 600. ABAQUS/CAE computes the cut-off frequency
from the SAE class as follows:
5
cut-o® frequency = SAE class £
3
Your X-Y data object must have a constant time step for it to be filtered. If the time step is not constant,
ABAQUS/CAE computes additional points at constant intervals by interpolation. The constant time
step for SAE filtering is defined by the smallest time step in the X-Y data object to be filtered.
Figure 30-19 illustrates the type of X-Y plot that can be produced using the saeFilter operation.
3. From the XY Data choices, click the name of the X-Y data object on which to operate. You can
8-919
X-Y plotting
choose from all X-Y data objects previously saved within this session (listed alphabetically in the
XY Data field).
The X-Y data object name appears within the saeFilter function parentheses in the expression
window.
5. To continue to build your expression, position the cursor in the expression window and type in or
select the functions, operators, and X-Y data you want to include.
7. To save your new X-Y data object, click Save As and then provide a name in the dialog box that
appears.
Saving your data object makes it available for future operations within this session and for
inclusion in X-Y plots containing multiple data objects.
8. When you are finished, click Dismiss to close the dialog box.
8-920
X-Y plotting
1
constant time step =
2 £ sampling frequency
Figure 30-20 illustrates the type of X-Y plot that can be produced using the sbFilter operation.
3. From the XY Data choices, click the name of the X-Y data object on which to operate. You can
choose from all X-Y data objects previously saved within this session (listed alphabetically in the
XY Data field).
The X-Y data object name appears within the sbFilter function parentheses in the expression
window.
4. Position your cursor after the data object name in the expression window and enter, in order, the
following three parameters separated by commas:
c. An even integer value for the number of poles; higher values increase computational effort
and can eventually cause the filter to become unstable.
8-921
X-Y plotting
5. To continue to build your expression, position the cursor in the expression window and type in or
select the functions, operators, and X-Y data you want to include.
7. To save your new X-Y data object, click Save As and then provide a name in the dialog box that
appears.
Saving your data object makes it available for future operations within this session and for
inclusion in X-Y plots containing multiple data objects.
8. When you are finished, click Dismiss to close the dialog box.
8-922
X-Y plotting
3. From the XY Data choices, click the name of the X-Y data object on which to operate. You can
choose from all X-Y data objects previously saved within this session (listed alphabetically in the
XY Data field).
The X-Y data object name appears within the smooth function parentheses in the expression
window.
4. Position your cursor in the expression window, and enter an integer value for the number of points
on either side of a given point to include in the average.
5. To continue to build your expression, position the cursor in the expression window and type in or
select the functions, operators, and X-Y data you want to include.
7. To save your new X-Y data object, click Save As and then provide a name in the dialog box that
appears.
Saving your data object makes it available for future operations within this session and for
inclusion in X-Y plots containing multiple data objects.
8. When you are finished, click Dismiss to close the dialog box.
8-923
X-Y plotting
Note: The last value of the new X-Y data object represents the overall maximum Y-coordinate of
the original X-Y data object.
For information on how to find the current maximum of two or more X-Y data objects, see ``Finding
the current maximum of two or more X-Y data objects,'' Section 30.4.29.
To find the current maximum of an X-Y data object:
8-924
X-Y plotting
3. From the XY Data choices, click the name of the X-Y data object on which to operate. You can
choose from all X-Y data objects previously saved within this session (listed alphabetically in the
XY Data field).
The X-Y data object name appears within the currentMax function parentheses in the expression
window.
4. To continue to build your expression, position the cursor in the expression window and type in or
select the functions, operators, and X-Y data you want to include.
6. To save your new X-Y data object, click Save As and then provide a name in the dialog box that
appears.
Saving your data object makes it available for future operations within this session and for
inclusion in X-Y plots containing multiple data objects.
7. When you are finished, click Dismiss to close the dialog box.
· ``Finding the current maximum of two or more X-Y data objects,'' Section 30.4.29
8-925
X-Y plotting
Note: The last value of the new X-Y data object represents the overall minimum Y-coordinate of
the original X-Y data object.
For information on how to find the current minimum of two or more X-Y data objects, see ``Finding the
current minimum of two or more X-Y data objects,'' Section 30.4.30.
To find the current minimum of an X-Y data object:
3. From the XY Data choices, click the name of the X-Y data object on which to operate. You can
choose from all X-Y data objects previously saved within this session (listed alphabetically in the
XY Data field).
The X-Y data object name appears within the currentMin function parentheses in the expression
window.
4. To continue to build your expression, position the cursor in the expression window and type in or
select the functions, operators, and X-Y data you want to include.
6. To save your new X-Y data object, click Save As and then provide a name in the dialog box that
appears.
Saving your data object makes it available for future operations within this session and for
inclusion in X-Y plots containing multiple data objects.
7. When you are finished, click Dismiss to close the dialog box.
8-926
X-Y plotting
· ``Finding the current minimum of two or more X-Y data objects,'' Section 30.4.30
Note: The last value of the new X-Y data object represents the overall range of Y-coordinates of
the original X-Y data object.
For information on how to find the current range of two or more X-Y data objects, see ``Finding the
current range of two or more X-Y data objects,'' Section 30.4.31.
To find the current range of an X-Y data object:
8-927
X-Y plotting
3. From the XY Data choices, click the name of the X-Y data object on which to operate. You can
choose from all X-Y data objects previously saved within this session (listed alphabetically in the
XY Data field).
The X-Y data object name appears within the currentRng function parentheses in the expression
window.
4. To continue to build your expression, position the cursor in the expression window and type in or
select the functions, operators, and X-Y data you want to include.
6. To save your new X-Y data object, click Save As and then provide a name in the dialog box that
appears.
Saving your data object makes it available for future operations within this session and for
inclusion in X-Y plots containing multiple data objects.
7. When you are finished, click Dismiss to close the dialog box.
· ``Finding the current range of two or more X-Y data objects,'' Section 30.4.31
8-928
X-Y plotting
For information on how to find the current maximum of a single X-Y data object, see ``Finding the
current maximum of an X-Y data object,'' Section 30.4.26.
To find the current maximum of two or more X-Y data objects:
3. From the XY Data choices, click the names of two or more X-Y data objects on which to operate.
Choices include all X-Y data objects previously saved within this session, listed alphabetically.
The X-Y data object names appear, separated by commas, within the maxEnvelope function
parentheses in the expression window.
4. To continue to build your expression, position the cursor in the expression window and type in or
select the functions, operators, and X-Y data you want to include.
6. To save your new X-Y data object, click Save As and then provide a name in the dialog box that
appears.
Saving your data object makes it available for future operations within this session and for
inclusion in X-Y plots containing multiple data objects.
7. When you are finished, click Dismiss to close the dialog box.
8-929
X-Y plotting
For information on how to find the current minimum of a single X-Y data object, see ``Finding the
current minimum of an X-Y data object,'' Section 30.4.27.
To find the current minimum of two or more X-Y data objects:
8-930
X-Y plotting
3. From the XY Data choices, click the names of two or more X-Y data objects on which to operate.
Choices include all previously saved X-Y data objects, which are listed alphabetically.
The X-Y data object names appear, separated by commas, within the minEnvelope function
parentheses in the expression window.
4. To continue to build your expression, position the cursor in the expression window and type in or
select the functions, operators, and X-Y data you want to include.
6. To save your new X-Y data object, click Save As and then provide a name in the dialog box that
appears.
Saving your data object makes it available for future operations within this session and for
inclusion in X-Y plots containing multiple data objects.
7. When you are finished, click Dismiss to close the dialog box.
8-931
X-Y plotting
For information on how to find the current range of a single X-Y data object, see ``Finding the current
range of an X-Y data object,'' Section 30.4.28.
To find the current range of two or more X-Y data objects:
3. From the XY Data choices, click the names of two or more X-Y data objects on which to operate.
Choices include all X-Y data objects previously saved within this session, listed alphabetically.
The X-Y data object names appear, separated by commas, within the rng function parentheses in
the expression window.
4. To continue to build your expression, position the cursor in the expression window and type in or
select the functions, operators, and X-Y data you want to include.
6. To save your new X-Y data object, click Save As and then provide a name in the dialog box that
appears.
Saving your data object makes it available for future operations within this session and for
inclusion in X-Y plots containing multiple data objects.
7. When you are finished, click Dismiss to close the dialog box.
8-932
X-Y plotting
8-933
X-Y plotting
3. From the XY Data choices, click the names of the X-Y data objects to append in the order you want
ABAQUS to concatenate them. You can choose from X-Y data objects previously saved within this
session (listed alphabetically in the XY Data field).
The X-Y data object names appear, separated by commas, within the append function parentheses
in the expression window.
4. To continue to build your expression, position the cursor in the expression window and type in or
select the functions, operators, and X-Y data you want to include.
6. To save your new X-Y data object, click Save As and then provide a name in the dialog box that
appears.
Saving your data object makes it available for future operations within this session and for
inclusion in X-Y plots containing multiple data objects.
7. When you are finished, click Dismiss to close the dialog box.
XYData1 = [(1; 4); (2; 4); (3; 4); (4; 5); (5; 6)]
and
XYData2 = [(1; 9); (2; 8); (3; 7); (4; 6); (5; 4)];
then
combine(XYData1, XYData2) = [(4; 9); (4; 8); (4; 7); (5; 6); (6; 4)]:
8-934
X-Y plotting
The arguments of this operation are not commutative. If X-coordinate values for the two data objects
do not match, ABAQUS/CAE computes the missing data points to allow the X-Y data objects to be
aligned. For more information on how missing data points are computed, see ``Understanding X-Y
data interpolation and extrapolation, '' Section 30.4.2.
A typical application of this function would be to combine a data object having X-values of time and
Y-values of load with a data object having X-values of time and Y-values of displacement to produce a
data object having X-values of displacement and Y-values of load. Another example would be to
combine a data object having X-values of time and Y-values of stress with a data object having
X-values of time and Y-values of strain to produce a data object having X-values of strain and Y-values
of stress, as shown in Figure 30-29.
3. From the XY Data choices, click the names of the two X-Y data objects to combine in the order
8-935
X-Y plotting
you want ABAQUS to combine them. Choices include all X-Y data objects previously saved
within this session, listed alphabetically.
The X-Y data object names appear, separated by commas, within the combine function
parentheses in the expression window.
4. To continue to build your expression, position the cursor in the expression window and type in or
select the functions, operators, and X-Y data you want to include.
6. To save your new X-Y data object, click Save As and then provide a name in the dialog box that
appears.
Saving your data object makes it available for future operations within this session and for
inclusion in X-Y plots containing multiple data objects.
7. When you are finished, click Dismiss to close the dialog box.
30.4.34 Converting the angular units used for X-Y data objects
Use the degreeToRadian or radianToDegree function to operate on a previously saved X-Y data
object (a collection of ordered pairs) to produce a new X-Y data object. The new X-Y data object has
the same X-coordinate values as the original X-Y data object. ABAQUS/CAE computes the new
Y-coordinate values by converting each original Y-coordinate from degrees to radians or from radians
to degrees, depending on the function you specify.
To apply the degreeToRadian or radianToDegree function:
2. From the Operators listed, click degreeToRadian to convert from degrees to radians or
radianToDegree to convert from radians to degrees.
8-936
X-Y plotting
3. From the XY Data choices, click the name of the X-Y data object on which to operate. You can
choose from all X-Y data objects previously saved within this session (listed alphabetically in the
XY Data field).
The X-Y data object name appears within the function parentheses in the expression window.
4. To continue to build your expression, position the cursor in the expression window and type in or
select the functions, operators, and X-Y data you want to include.
6. To save your new X-Y data object, click Save As and then provide a name in the dialog box that
appears.
Saving your data object makes it available for future operations within this session and for
inclusion in X-Y plots containing multiple data objects.
7. When you are finished, click Dismiss to close the dialog box.
8-937
X-Y plotting
3. From the XY Data choices, click the name of the X-Y data object on which to operate. You can
choose from all X-Y data objects previously saved within this session (listed alphabetically in the
XY Data field).
The X-Y data object name appears within the swap function parentheses in the expression
window.
4. To continue to build your expression, position the cursor in the expression window and type in or
select the functions, operators, and X-Y data you want to include.
6. To save your new X-Y data object, click Save As and then provide a name in the dialog box that
appears.
Saving your data object makes it available for future operations within this session and for
inclusion in X-Y plots containing multiple data objects.
7. When you are finished, click Dismiss to close the dialog box.
8-938
X-Y plotting
· ``Customizing the X-Y plot axis color and style,'' Section 30.5.8
8-939
X-Y plotting
Select Options->XY Plot from the main menu bar to access the XY Plot Options dialog box. Click the
following tabs to customize the appearance of X-Y plots in the current viewport:
· Axes: Choose axes color and thickness, and control numeric axes labels.
8-940
X-Y plotting
· ``Customizing the X-Y plot axis color and style,'' Section 30.5.8
2. From the X-axis Type options, click Linear or Logarithmic to choose the scale of the X-axis.
3. From the Y-axis Type options, click Linear or Logarithmic to choose the scale of the Y-axis.
8-941
X-Y plotting
Max: Auto-compute
ABAQUS computes the maximum value of the X-axis, which is rounded to provide
reasonable tick mark intervals.
Max: Specify
The Specify text field becomes available, and you can specify the maximum value of the
X-axis.
Min: Auto-compute
ABAQUS computes the minimum value of the X-axis, which is rounded to provide
reasonable tick mark intervals.
Min: Specify
The Specify text field becomes available, and you can enter the minimum value of the
X-axis.
Figure 30-32 X-Y plot with major and minor tick marks indicated.
8-942
X-Y plotting
Major tick marks govern the placement of the X-Y plot major grid and the numeric axis labels. Minor
tick marks are shorter, unlabeled marks governing the placement of the minor grid lines.
By default, ABAQUS/CAE automatically computes the number of tick marks. You can specify major
tick marks by giving the increment between them or the total number of tick marks. You can specify
minor tick marks only by giving the total number between each major tick mark.
The color of the tick marks is governed by the color of the axes. For more information, see
``Customizing the X-Y plot axis color and style,'' Section 30.5.8.
To control the axis tick marks of an X-Y plot:
2. Choose the method of computing the interval between major tick marks along the X-axis.
From the X-Axis Major options, choose one of the following:
Auto-compute
ABAQUS computes the interval between major tick marks along the X-axis, rounding to
provide reasonable intervals.
Increment
The Increment text field becomes available, and you can enter the increment between
major tick marks along the X-axis.
8-943
X-Y plotting
Total number
The Total number text field becomes available, and you can enter the total number of
major tick marks to appear between the minimum and maximum values along the X-axis.
Figure 30-33 X-Y plot with major and minor grid lines indicated.
8-944
X-Y plotting
You can enable and disable the horizontal and vertical lines in either the major or minor grid, and you
can select the color, style, and thickness of the lines in each grid.
Note: Major grid lines originate from major tick marks, and minor grid lines originate from minor
tick marks. To control the interval between grid lines, you must adjust the spacing of the tick
marks.
2. From the Major Grid Lines options, toggle Show horizontal lines and Show vertical lines to
display or suppress the horizontal and vertical lines of the major grid.
When either Show horizontal lines or Show vertical lines is on, grid line style, color, and
thickness options become available.
a. Click the Style button to reveal the major grid line style options.
8-945
X-Y plotting
a. Click the Color arrow to reveal the major grid line color options.
a. Click the Thickness button to reveal the major grid lines thickness options.
6. To select the Minor Grid Lines options, repeat Step 2 through Step 5.
8-946
X-Y plotting
Click the Titles tab in the dialog box that appears; the Titles options appear.
b. In the Title text field, enter the text that you wish to appear along the X-axis.
a. Click the Color arrow to reveal the X-axis title color options.
b. Use the font selector dialog box to set the font properties that you want.
Note: You specify font size as a percentage of the viewport.
d. Click OK to close the Select Font dialog box and to return to the axes titles options.
8-947
X-Y plotting
The color of the labels is governed by the color of the axes. See ``Customizing the X-Y plot axis color
and style,'' Section 30.5.8, for more information.
To control the axes labels of an X-Y plot:
2. From the X-Axis Labels options, select the format of the X-axis labels.
a. Click the Format button to reveal the X-axis label format options.
Automatic
8-948
X-Y plotting
Based on the values of your X-Y data, ABAQUS automatically selects decimal or
exponential labels with the specified number of decimal places. This method is
the default.
Decimal
Use decimal format with the specified number of decimal places.
Exponential
Use exponential format with the specified number of decimal places.
3. Click the Decimal places arrows to specify the desired number of decimal places in each label.
4. Click the Frequency arrows to specify how often labels are printed relative to each major tick
mark. For example, if you select a frequency of two, labels will appear at every second major tick
mark along the axis. If you select a frequency of zero, no labels will be displayed along the axis.
You can request a label frequency of at most one greater than the number of major tick marks.
b. Use the font selector dialog box to object the font properties that you want.
Note: You specify font size as a percentage of the viewport.
d. Click OK to close the Select Font dialog box and return to the axes labels options.
8-949
X-Y plotting
8-950
X-Y plotting
2. To adjust the relative scaling of the X- and Y-axis, drag one or both of the X-Axis and Y-Axis
sliders.
When you stop dragging the slider, the aspect ratio appears in both X:Y and Y:X form at the
bottom of the Aspect Ratio frame. Continue dragging until the desired ratio is achieved.
8-951
X-Y plotting
· The text that appears in the legend describing the data. For more information, see ``Customizing
the X-Y plot legend,'' Section 30.6.3.
· The appearance of the line representing the data (the curve). For more information, see
``Customizing the appearance of an X-Y curve,'' Section 30.6.4.
· The appearance of the symbols along the curve. For more information, see ``Customizing the
symbols used on an X-Y curve,'' Section 30.6.5.
1. From the main menu bar, select Options->XY Curve; the XY Curve Options dialog box appears.
2. Use the curve options to select and then customize the appearance of the X-Y curves in the current
viewport. ABAQUS/CAE immediately applies your changes.
3. To restore the default appearance of one or more selected curves, click Defaults.
4. When you have finished customizing the appearance of your X-Y curves, click Dismiss to close
8-952
X-Y plotting
2. Select one or more X-Y curves to customize. For more information on selecting multiple items in
dialog boxes, see ``Selecting multiple items in lists,'' Section 6.3.8.
Note: To make an X-Y curve available for selection, you must first plot it.
If you have selected one curve, the Attributes frame displays the current attributes of that curve.
If you have selected multiple curves, ABAQUS/CAE displays the Legend text field as blank. The
display in the Attributes frame varies depending on whether the selected curves have the same
attributes or not. If the attributes are the same, ABAQUS/CAE displays them; if the attributes
differ, ABAQUS/CAE displays the following:
· The line Color and symbol Color text fields display the term As is.
8-953
X-Y plotting
· The text that appears in the legend describing the data. For more information, see
``Customizing the X-Y plot legend,'' Section 30.6.3.
· The appearance of the line representing the data (the curve). For more information, see
``Customizing the appearance of an X-Y curve,'' Section 30.6.4.
· The appearance of the symbols along the curve. For more information, see ``Customizing the
symbols used on an X-Y curve,'' Section 30.6.5.
2. From the XY Data field, select the single X-Y curve whose legend text you wish to customize.
Note: To make an X-Y curve available for selection, you must first plot it.
4. In the Legend text field, enter the text that you wish to appear in the legend for the X-Y curve you
have selected. Your text can include blank spaces.
6. Repeat Steps 2 through 5 for each curve whose legend text you wish to customize.
8-954
X-Y plotting
The color, style, and thickness that you select appear along the curve and in the legend. The
customizing options are available only when Show line is toggled on.
To customize the appearance of a curve in an X-Y plot:
2. From the XY Data field, select one or more X-Y curves whose attributes you wish to customize.
Note: To make an X-Y curve available for selection, you must first plot it.
The customization options you choose will apply to all of the curves you have selected; if you
want to vary the appearance of multiple curves, you must customize them one at a time.
3. Toggle Show line to display or suppress the line representing each selected X-Y curve.
When Show line is on, the curve is displayed and the line attribute options are enabled.
8-955
X-Y plotting
a. Click the Style button to reveal the line style options (solid, dashed, etc.).
In the plot and in the legend, the line representing each selected X-Y curve changes to reflect your
specifications. For more information on the legend, see ``Customizing the legend,'' Section 38.1.
Your changes are saved for the duration of the session and will affect all subsequent X-Y plots of this
data.
8-956
X-Y plotting
The symbol that you select appears along the curve and in the legend. The customization options are
available only when Show symbol is toggled on.
To customize the symbols used on an X-Y curve:
2. From the XY Data field, select one or more X-Y curves whose symbols you wish to customize.
Note: To make an X-Y data object available for selection, you must first plot it.
The customization options you choose will apply to all of the curves you have selected; if you
want to vary the symbols on multiple curves, you must customize them one at a time.
3. Toggle Show symbol to display or suppress the symbols representing each selected X-Y curve's
data points.
When Show symbol is on, symbols are displayed and the symbol attributes are enabled.
8-957
X-Y plotting
b. From the symbol size options, click the desired symbol size.
The specified symbol size appears on the Size button.
Along each selected curve and in the legend, the symbol representing the selected X-Y data points
changes to reflect your specifications. For more information on the legend, see ``Customizing the
legend,'' Section 38.1.
Your changes are saved for the duration of the session and will affect all subsequent X-Y plots of this
data.
8-958
Querying and probing
For information on writing selected probe values to a file, see Chapter 35, "Generating tabular data
reports." For information on using the query toolset to obtain linearized stresses, see Chapter 33,
"Calculating linearized stresses."
Select Tools->Query from the main menu bar, or select the query tool from the toolbar to use the
query toolset. Items under General Queries provide the following information:
When you select Tools->Query from the main menu bar or use the tool in the toolbar and select
Probe values, ABAQUS/CAE enters probe mode. In this mode ABAQUS/CAE displays information
in the Probe Values dialog box as you move the cursor over the model in the current viewport.
Probing a model plot displays model data and analysis results; probing an X-Y plot displays X-Y curve
data. You can write this information to a file.
The Probe Values dialog box contains two separate display areas. ABAQUS/CAE updates the
Current Probe Values portion of the dialog box continuously to show the current probe values as you
move the cursor over the model in the current viewport. ABAQUS/CAE updates the Selected Probe
Values portion of the dialog box only when you click in the viewport to select values of interest.
Values accumulate in the bottom portion of the dialog box until you either delete them, clear the table,
or cancel probe mode.
This section explains the following topics:
9-959
Querying and probing
Probing nodes
When you choose to probe nodes and position the cursor over a nodal location in the current
viewport, ABAQUS/CAE highlights the node and displays its label in the Probe Values
dialog box. In addition, you can choose to display any or all of the following:
· the node's deformed coordinates (using the current deformed field output variable),
Probing elements
When you choose to probe elements and position the cursor over an element in the current
viewport, ABAQUS/CAE highlights the element and displays its label and type in the Probe
Values dialog box. In addition, you can choose to display either or both of the following:
Regardless of the render style in which the model is displayed, only visible elements can be
9-960
Querying and probing
probed. If necessary, you can create a display group to reveal otherwise unavailable interior
elements.
For information on writing selected probe values to a file, see Chapter 35, "Generating tabular data
reports."
General Queries
Node
You can obtain information on the coordinates and displacement of a particular node.
Distance
You can obtain information on the distance between two points or nodes.
For more information on general model queries, see ``Obtaining general model information,''
Section 31.3.2.
Visualization Queries
Probe values
9-961
Querying and probing
ABAQUS/CAE displays information in the Probe Values dialog box as you move the
cursor around the current viewport. Probing a model plot displays model data and analysis
results; probing an X-Y plot displays X-Y curve data. For more information on probing, see
``Probing nodes,'' Section 31.3.4, ``Probing elements,'' Section 31.3.5, and ``Probing X-Y
plots,'' Section 31.3.6.
Stress linearization
Stress linearization is the separation of stresses through a section into constant membrane
and linear bending stresses. ABAQUS performs stress linearization calculations and
displays the results in the form of an X-Y plot. For more information on stress
linearization, see Chapter 33, "Calculating linearized stresses."
From the main menu bar, select Tools->Query or click the tool in the toolbar.
The Query dialog box appears.
a. Select Node from the General Queries field of the Query dialog box, and click Apply.
ABAQUS displays a prompt in the prompt area.
a. Select Distance from the General Queries field of the Query dialog box, and click
Apply.
9-962
Querying and probing
· the undeformed and deformed X-, Y -, and Z-coordinates of each node, along with the
node's displacement;
· the X-, Y -, and Z-components of the undeformed and deformed vector between the
two nodes;
· the X-, Y -, and Z-components of the relative displacement between the two nodes.
c. To resize the message area, drag the small square at its upper right corner; to see
information that has scrolled out of the message area, use the scroll bar on the right
side.
The same information that appears in the message area is also written to the replay file.
9-963
Querying and probing
· the node's deformed coordinates (using the current deformed field output variable),
To help locate nodes in the viewport, you may want to produce a model plot with node symbols visible
before using the query toolset. For more information, see ``Customizing node symbols,'' Section
37.6.5.
To probe nodes:
From the main menu bar, select Tools->Query or click the tool in the toolbar. Select Probe
values in the dialog box that appears; then click Apply. The Probe Values dialog box appears.
2. Select the step, frame, field output variable, and result options governing the probe data and results
ABAQUS/CAE will display.
In the Probe Values dialog box, the Current ODB Settings field identifies the current step,
frame, and field output variable.
· To change the field output variable or result options, click Field Output.
9-964
Querying and probing
b. In the Current Probe Values table, click anywhere along a table row to toggle probe
display of the item listed in the second column.
4. Move the cursor to probe the model plot in the current viewport.
As you position the cursor over a node, ABAQUS/CAE displays the values of the items you have
requested in the Current Probe Values table in the Probe Values dialog box.
5. To select and accumulate values of interest, and to allow subsequent writing of these values to a
file, click mouse button 1 while positioning the cursor over a node.
ABAQUS/CAE stores the data from the Current Probe Values table into the Selected Probe
Values table. To identify your data, ABAQUS/CAE always includes the Part Instance and Node
ID.
6. To delete data from the Selected Probe Values table or to clear or sort the table, click mouse
button 3. For more information, see ``Entering tabular data,'' Section 6.3.5.
7. To save the data you have selected, click Write to File. For more information, see Chapter 35,
"Generating tabular data reports."
9-965
Querying and probing
Only exterior elements can be queried. If necessary, you can create a display group to reveal otherwise
unavailable interior elements. For more information, see Chapter 36, "Displaying a subset of your
model."
To help locate elements in the viewport, you may want to produce a model plot with all element edges
visible before using the query toolset. For more information, see ``Controlling element and surface
edge visibility,'' Section 37.3.1.
To probe elements:
From the main menu bar, select Tools->Query or click the tool in the toolbar. Select Probe
values in the dialog box that appears; then click Apply. The Probe Values dialog box appears.
2. Select the step, frame, and field output variable for which ABAQUS/CAE will obtain values.
In the Probe Values dialog box, the Current ODB Settings field identifies the current step,
frame, and field output variable.
b. In the Current Probe Values table, click anywhere along a table row to toggle probe
display of the item listed in the second column.
Note: Field output is available only if the current primary variable is an element-based variable, such as stress or
strain.
When you toggle on a row that contains the field output variable, the Position options
become available.
c. To choose the output position at which a field output variable is displayed, click the
Position arrow and select either Integration Pt, Centroid, Element Nodal, or Element
Face.
4. Move the cursor to probe the model plot in the current viewport.
As you position the cursor over an element, ABAQUS/CAE displays the values of the items you
have requested in the Current Probe Values table in the Probe Values dialog box.
9-966
Querying and probing
5. To select and accumulate values of interest, and to allow subsequent writing of these values to a
file, click mouse button 1 while positioning the cursor over an element.
ABAQUS/CAE stores the data from the Current Probe Values table into the Selected Probe
Values table. To identify your data, ABAQUS/CAE always includes the Part Instance, Element
ID, and Type.
6. To delete data from the Selected Probe Values table or to clear or sort the table, click mouse
button 3. For more information, see ``Entering tabular data,'' Section 6.3.5.
7. To save the data you have selected, click Write to File. For more information, see Chapter 35,
"Generating tabular data reports."
9-967
Querying and probing
From the main menu bar, select Tools->Query or click the tool in the toolbar. Select Probe
values in the dialog box that appears; then click Apply. The Probe Values dialog box appears.
2. At the top of the dialog box, toggle Interpolate between points to enable or disable the display
of probe values for arbitrary points along the curve.
When you enable interpolation, ABAQUS/CAE displays the sequence identification of arbitrary
points by listing the bracketing X-Y data object points in parentheses.
3. In the Current Probe Values field, click table rows to toggle probe display.
4. Move the cursor to probe the X-Y plot in the current viewport.
As you position the cursor over a curve point, ABAQUS/CAE displays the values of the items you
have requested in the Current Probe Values table in the Probe Values dialog box.
5. To select and accumulate values of interest, and to allow subsequent writing of these values to a
file, click mouse button 1 while positioning the cursor over a curve point.
ABAQUS/CAE stores the legend text, sequence identification, and X- and Y-coordinates of the
current point into the Selected Probe Values table.
6. To delete data from the Selected Probe Values table or to clear or sort the table, click mouse
button 3. For more information, see ``Entering tabular data,'' Section 6.3.5.
7. To save the data you have selected, click Write to File. For more information, see Chapter 35,
"Generating tabular data reports."
9-968
Viewing results along a path
Node list
The points making up the path consist of nodal locations only. You specify the points using
node labels and node label ranges. A node label is a persistent means of referring to a given
node; that is, node labels do not change as your model deforms. Because of this, the node
labels that comprise a node list path are equally applicable to the undeformed or the deformed
model shape. However, node labels are part instance-specific. In other words, you can have
the same node label for multiple part instances; therefore, you must specify to which part
instance you are referring when you use node labels. For more information, see ``Creating or
editing a node list path,'' Section 32.2.1.
Point list
The points making up the path consist of coordinate locations within your model. These
locations may or may not coincide with nodal locations. Point list coordinates remain fixed in
space and are independent of your model. For example, coordinates that coincide with a nodal
location on the undeformed shape may not coincide with any location on the deformed shape.
By the same logic, point list coordinates are independent of specific part instances. For more
information, see ``Creating or editing a point list path,'' Section 32.2.2.
ABAQUS/CAE forms the path by connecting the nodes or points that you specify in the order you
10-969
Viewing results along a path
have given.
After you create a path, you can select Tools->Path from the main menu bar to edit, copy, rename,
delete, or plot it. Plotting the path itself is a means to verify visually that you have specified the
intended line; to view results along the path, you must form X-Y data pairs and produce an X-Y plot.
For more information on managing paths, see ``Managing objects using manager dialog boxes,''
Section 6.5.6; for more information on producing an X-Y plot of path data, see ``Obtaining X-Y data
along a path,'' Section 32.3.
· True distance: X-values correspond to each point's actual distance along the path in
model space coordinates, starting with zero.
· Normalized distance : X-values correspond to each point's distance along the path as a
fraction of the total length of the path.
· Sequence ID: X-values correspond to the order in which each point occurs in the path
result list.
· X, Y, or Z distance: X-values correspond to each point's actual distance along the path in
the single coordinate direction you specify, starting with zero. This option is particularly
useful for generating a plot of results versus radius in an axisymmetric model.
10-970
Viewing results along a path
variable for which ABAQUS/CAE obtains results and by controlling how ABAQUS/CAE
computes certain types of results, as follows:
· For element-based field output variables such as stress or strain to be obtained at nodal
locations, ABAQUS/CAE reads results from the output database, extrapolates those
values to the nodes, then conditionally averages multiple contributions according to
options you select.
· For both node-based and element-based variables to be obtained at path points that do not
coincide with nodal locations, ABAQUS/CAE computes values by interpolating from the
nodes to the requested location using a geometric approximation of the element's shape.
You cannot control this computation.
The averaging options for element-based variables are located in the Field Output dialog box.
Averaging reduces multiple contributions into a single value. When you select result options
to partially or fully suppress averaging, path points receiving multiple contributions produce
multiple data pairs. Such data pairs share the same X-value but have a separate Y-value for
each contribution. Depending on your path and on the characteristics of your model, the
following techniques may be necessary to avoid multiple data pairs sharing the same X-value:
· Use display groups to isolate individual regions prior to obtaining results along a path.
For more information on value averaging, see ``Understanding result value averaging,'' Section
24.4.2.
ABAQUS/CAE does not form data pairs for points that do not have results for the specified
step, frame, or field output variable.
10-971
Viewing results along a path
a. From the main menu bar, select Tools->Path->Create. The Create Path dialog box appears.
b. ABAQUS displays a default name for the path in the Name text field. To provide a more
meaningful name, replace this default with the name of your choice (including blank spaces if
you wish).
c. In the Create Path dialog box, click Node list; then click Continue.
a. From the main menu bar, select Tools->Path->Edit. From the menu that appears, select the
path you want to edit.
Tip: You can also use the Path Manager to edit a path. From the main menu bar, select
Tools->Path->Manager to display the manager. Select the path you want to edit, and
click Edit from the buttons on the right side of the manager.
2. Choose the part instance for which you are specifying nodes. Click the arrow next to the Part
instance field to see a list of the available part instances.
3. To specify the nodes along your path, use either of the following techniques:
Enter the node labels directly into the table:
a. In the Node Labels table, use standard keyboard and mouse editing techniques to insert,
modify, or delete node label expressions. A node label expression is either of the following:
- A range of nodes that you specify with a starting and ending node label optionally
followed by an increment; for example, 5:10 or 5:10:2.
10-972
Viewing results along a path
For special table editing options or to read data from an ASCII file, press mouse button 3. (For
more information, see ``Entering tabular data,'' Section 6.3.5.)
a. Click Select.
Select nodes to be inserted into the path appears in the prompt area, and the Edit Node
List Path dialog box disappears.
b. Select one or more nodes from the viewport (for more information, see Chapter 9, "Selecting
objects within the viewport").
ABAQUS highlights the nodes as you select them and displays the node labels and the path
connectivity.
Note: You can only select nodes that are in the current display group and part instance.
10-973
Viewing results along a path
with nodal locations, you can specify the node label and ABAQUS will enter the undeformed
coordinates of the node into the table. To help determine which node labels are of interest, you may
want to produce a model plot with node symbols and node numbers visible prior to creating the path.
For more information, see ``Customizing model labels,'' Section 37.6.
To create or edit a point list path:
a. From the main menu bar, select Tools->Path->Create. The Create Path dialog box appears.
b. ABAQUS displays a default name for the path in the Name text field. To provide a more
meaningful name, replace this default with the name of your choice (including blank spaces if
you wish).
c. In the Create Path dialog box, click Point list; then click Continue.
a. From the main menu bar, select Tools->Path->Edit. From the menu that appears, select the
path you want to edit.
Tip: You can also use the Path Manager to edit a path. From the main menu bar, select
Tools->Path->Manager to display the manager. Select the path you want to edit, and
click Edit from the buttons on the right side of the manager.
2. In the Point Coordinates table, use standard keyboard and mouse editing techniques to enter,
modify, or delete coordinates.
To enter coordinates, use either of the following techniques:
Type in the coordinate values of a point:
a. Specify the values as X-, Y-, Z-coordinates separated by spaces or commas; for example, 1.0,
3.4, 2.0.
b. Click [Enter].
a. Choose the part instance for which you want to determine nodal coordinates. Click the arrow
next to the Part instance field to see a list of the available part instances.
To obtain the coordinates of a node, type the node label into the Node label field; then click
either [Enter] or Query.
10-974
Viewing results along a path
ABAQUS displays the undeformed X-, Y-, and Z-coordinates of the node.
b. To enter these coordinates into the path definition table before, after, or at the currently
highlighted row, click Add Before, Add After, or Replace, respectively.
For special table editing options or to read data from an ASCII file, press mouse button 3. (For
more information, see ``Entering tabular data,'' Section 6.3.5.)
On the model plot in the current viewport, ABAQUS highlights all points included in the path and
displays the path connectivity.
· ``Choosing the path locations at which to obtain data, '' Section 32.3.1
10-975
Viewing results along a path
a nodal location on the undeformed shape may not coincide with any location on the deformed shape.
ABAQUS does not form data pairs for points that do not coincide with your model.
To choose the path locations at which to obtain data:
2. Click the Path arrow to select the path for which to obtain data.
The model plot in the current viewport changes to highlight the path you have selected.
3. Click the Undeformed or Deformed to choose whether ABAQUS interprets the points that make
up the path as locations on the undeformed or the deformed model shape, respectively.
4. To obtain X-Y data at locations where the path intersects the model as well as at the points that
make up the path, click Include intersections. The default is to obtain data only at the points that
make up the path.
7. When you have finished, click Cancel to close the dialog box.
10-976
Viewing results along a path
based on the points you have specified for the path and optionally on additional points where your path
intersects the model. For more information, see ``Choosing the path locations at which to obtain data, ''
Section 32.3.1.
The node labels or point coordinates that comprise a path are usually not in a form suitable for direct
use as X-values. ABAQUS offers several options for you to convert this series of points to useful
X-values and subsequent X-Y plot axis labels.
To control data pair X-values:
2. At the top of the dialog box, click the Path arrow to select the path for which to obtain data.
The model plot in the current viewport changes to highlight the path you have selected.
3. In the X Values field, choose one of the following options to convert path points to X Values:
· True distance: X-values correspond to each point's actual distance along the path in model
space coordinates, starting with zero.
· Normalized distance : X-values correspond to each point's distance along the path as a
fraction of the total length of the path.
· Sequence ID: X-values correspond to the order in which each point occurs in the path result
list.
· X, Y, or Z distance: X-values correspond to each point's actual distance along the path in the
single coordinate direction you specify, starting with zero. This option is particularly useful for
generating a plot of results versus radius in an axisymmetric model.
5. To save the X-Y data pairs you have configured as an X-Y data object , click Save As.
Note: To plot your saved X-Y data object, select Tools->XY Data->Plot from the main menu bar and choose the X-Y data
object from the pull-right menu.
6. When you have finished, click Cancel to close the dialog box.
10-977
Viewing results along a path
2. At the top of the dialog box, click the Path arrow to select the path for which to obtain data.
The model plot in the current viewport changes to highlight the path you have selected.
3. The Y Values field identifies the step, frame, and field output variable for which ABAQUS will
obtain results.
· To change the step or frame, click Frame. For more information, see ``Selecting the results
step and frame,'' Section 24.2.
· To change the field output variable, click Field Output. For more information, see ``Selecting
the primary field output variable,'' Section 24.3.2.
· The averaging of element-based field output values is controlled by the result options settings
for the current viewport. To view or change these settings, click Field Output. For more
information, see ``Controlling result averaging,'' Section 24.4.4.
ABAQUS refreshes the Y Values field and the deformed, contour, or symbol plot in the current
viewport according to any changes you apply to the step, frame, field output variable, or result
options.
5. To save the X-Y data pairs you have configured as an X-Y data object, click Save As.
Note: To plot your saved X-Y data object, select Tools->XY Data->Plot from the main menu bar and choose the X-Y data
10-978
Viewing results along a path
6. When you have finished, click Cancel to close the dialog box.
10-979
Calculating linearized stresses
· You define a section through your model. You specify the end points of the section by selecting
nodes in the model or coordinates in space.
· ABAQUS/CAE defines the stress line by interpolating between the two end points to obtain a
user-specified number of equal intervals along a straight line.
· The specified stress results are obtained at the equally spaced points along the line in a local
coordinate system defined by the line.
· ABAQUS/CAE performs stress linearization calculations and displays the results in the form of an
X-Y plot. You can choose to save the data and/or to write it to a file.
11-980
Calculating linearized stresses
The section can extend from surface to surface, or it can be entirely in the interior of the model. The
following guidelines should also be considered when selecting the end points for the section:
· Use display groups to isolate individual regions prior to specifying the section.
If the section extends across spatial discontinuities, such as a hole, an error message will be given.
Material discontinuities will not generate an error.
After you choose the end points of the section, you can specify the number of segments into which the
line should be divided or you can accept the default number. ABAQUS/CAE defines the stress line by
interpolating between the two end points to obtain the specified number of equal intervals along a
straight line.
Nonaxisymmetric models
The membrane and bending stresses for nonaxisymmetric models are calculated by integrating
11-981
Calculating linearized stresses
Axisymmetric models
ABAQUS calculates the linearized stresses for axisymmetric models using the following
equations:
F
¾m = membrane stress = ;
A
M ¢c
¾b = bending stress = ;
I
where F is the sum of the forces acting at a point, A is the area over which the forces are
acting, M is the bending moment, c is the distance from the neutral axis of the section, and I
is the moment of inertia. These values are obtained differently for the membrane, meridional,
hoop, and shear stresses.
For further information on stress linearization theory, refer to the following sources:
· Kroenke, W. C., "Classification of Finite Element Stresses According to ASME Section III Stress
Categories," ASME 94th Winter Annual Meeting, November 1973.
From the main menu bar, select Tools->Query or click the tool in the toolbar.
The Query dialog box appears.
11-982
Calculating linearized stresses
3. In the Stress line name field, provide a name for the stress line. This name will be used as a
prefix for the linearized results.
4. To save the X-Y data that will be generated, toggle on Save XY data. The data will be available for
the duration of your ABAQUS/CAE session.
5. Select the first end point for the stress line by selecting a node or a point in space.
Select a node
This is the default method. You can either type in a node label or select a node directly
from the viewport.
a. Click the arrow in the field next to Point 1, and select Coordinates from the list that
appears.
b. Enter a set of coordinates for Point 1. Specify the values as X-, Y -, and
Z-coordinates separated by spaces or commas; for example, 1.0, 3.4, 2.0.
6. Repeat either of the above procedures to select the second endpoint for the stress line, Point 2.
To verify the line that you have specified, click Highlight stress line. ABAQUS highlights the
line in the viewport.
8. Choose the model shape for which to obtain the stress results. The default is to obtain the results
for the deformed model shape. Toggle on Undeformed to obtain results for the undeformed model
shape.
9. Specify the number of intervals into which the stress line should be divided. Type a positive
integer greater than 0 into the Number of intervals on stress line text field. If you do not enter a
11-983
Calculating linearized stresses
10. For axisymmetric models enter an approximate value for the radius of curvature of the midplane of
your model at the location of the stress line. The default value is Infinity, which implies a lack of
curvature. To specify a radius of curvature, click Specify and enter a number in the text field that
appears.
11. To write the linearized stress values to a file, toggle on Write to file in the Report area of the
dialog box. The File name field will become available with a default file name of
linearStress.rpt. Use the default name, enter a new name for your report, or click Select
and choose from the list of existing files that appears.
The default is to append new data to the file; if you wish to overwrite the file, toggle off Append
to file.
11-984
Calculating linearized stresses
11-985
Animating plots
Object-based animation
Object-based animation is the display of a sequence of either deformed shape plots, contour
plots, or symbol plots. ABAQUS/CAE can produce two different types of sequences of these
plots. These two sequence types are called ``time history animation'' and ``scale factor
animation.''
Animating by time history produces a sequence of deformed shape, contour, or symbol plots
that vary over time according to actual analysis results. Animating by scale factor produces a
sequence of images that vary only in the scaling of a single deformed shape, contour, or
symbol plot. To better understand these two types of animation, see ``Time history animation,''
Section 34.1.1, and ``Scale factor animation,'' Section 34.1.2, respectively.
While an object-based animation is playing, you can dynamically change display
characteristics such as the view, any viewport annotations, and plot mode-dependent
customization options.
Image-based animation
Image-based animation is the playback of an animation file. You create an animation file in
ABAQUS/CAE by first playing object-based animations in one or more viewports and then
selecting Animate->Save As from the main menu bar. Once saved, your animation can be
replayed from within ABAQUS/CAE or played external to ABAQUS/CAE using the
ABAQUS movie player utility or industry-standard animation software. You can choose to
save your image-based animation file in either QuickTime or Audio Video Interleave ( AVI)
format.
In general, animation playback from a file provides better performance than object-based
animation, particularly for large models. While an image-based animation is playing, you
cannot change display characteristics.
12-986
Animating plots
In a time history animation ABAQUS/CAE creates the images in the sequence by redrawing the
deformed shape, contour, or symbol plot for every frame found in the output database for the selected
steps. Each image in a time history animation displays actual analysis results.
If you are animating a contour plot, the display of the contour values depends on options you select.
The default behavior is for the values within the legend to scale with each image; however, if you use
the contour options to specify contour limits, the legend remains constant. To learn how to set contour
limits, see ``Setting contour limits,'' Section 27.4.6.
12-987
Animating plots
animation. In a scale factor animation you can customize the apparent motion of your model. For both
types of animation you can customize the underlying deformed shape, contour, or symbol plot.
At any time before or during object-based animation playback you can customize the deformed shape,
contour, or symbol plot that underlies your animation. For example, you can toggle the legend, adjust
the deformation scale factor, or choose a different field output variable. Use the View , Result, and
Options menus and the tools on the toolbar to customize the underlying plot of your animation.
This section explains how to produce and customize ABAQUS/CAE object-based time history and
scale factor animations. (Customization does not apply to image-based animations, which are played
from a file and cannot be customized.) The following topics are covered:
1. Use the File menu to open the output database containing your analysis results.
2. To plot variables other than those ABAQUS selects by default, use the Result menu.
· For animation of a deformed plot, select the deformed field output variable for which
ABAQUS obtains values over time.
· For animation of a contour or symbol plot, select the primary field output variable to display.
If you want to display your animating contour or symbol plot on the deformed shape, select the
deformed field variable. For more information on field output variable selection, see
``Overview of field output variable selection, '' Section 24.3.1.
3. From the main menu bar, select Options->Animation; then click the Time History tab in the
dialog box that appears.
Select the steps to include in the animation.
4. Use the Options and View menus to select the customization options that you want. These may
include deformed, contour, symbol, and view options.
5. To initiate the animation, select Animate->Time History from the main menu bar.
12-988
Animating plots
Tip: You can also produce a time history animation using the tool in the toolbox.
Animation begins in the current viewport, and the animation controls appear in the prompt area.
ABAQUS is now in the time history animation plot mode. In this mode ABAQUS automatically
refreshes your plot each time you click Apply or OK in the Results, Options, or View menu
dialog boxes. The current viewport remains in the time history animation mode until you produce
a plot in some other (for example, undeformed, deformed) mode. To learn how to control the
animation, see ``Controlling animation playback,'' Section 34.4.
2. Click steps to toggle their inclusion in your animation. (For more information, see ``Selecting
multiple items in lists,'' Section 6.3.8.)
12-989
Animating plots
1. Use the File menu to open the output database containing your analysis results.
2. Use the Result menu to select the analysis results to be plotted, including the step and frame, the
deformed field output variable, and, for contour or symbol plot animation, the primary field output
variable to be plotted. For more information on field output variable selection, see ``Overview of
field output variable selection, '' Section 24.3.1.
3. Use the Options and View menus to select the customization options that you want.
4. To initiate the animation, select Animate->Scale Factor from the main menu bar.
Tip: You can also produce a scale factor animation using the tool in the toolbox.
Animation begins in the current viewport, and the animation controls appear in the prompt area.
ABAQUS is now in the scale factor animation plot mode. In this mode ABAQUS automatically
refreshes your plot each time you click Apply or OK in the Results, Options, or View menu
dialog boxes. The current viewport will remain in the scale factor animation mode until you
produce a plot in some other (for example, undeformed, deformed) mode. For more information on
customizing the underlying model shape, see ``Choosing the underlying model shape for contour,
symbol, and material orientation plots,'' Section 37.5.1.
12-990
Animating plots
You can customize the apparent motion of your animated model by choosing between the scale factor
range 0 to 1 and the extended range -1 to 1. The extended range is useful, for instance, to visualize a
vibration mode obtained by modal analysis. You can also vary the number of frames (separate images)
in the animation. A greater number of frames produces a smoother animation.
ABAQUS/CAE divides the scale factor range by the number of frames to compute the animation scale
factor values. These values are applied to the deformation scale factors in each coordinate direction
and to the field output variable values to produce each image in the animation sequence.
To customize a scale factor animation:
2. To control the range of scale factors, click -1 to 1 or 0 to 1 to choose the Relative Scaling you
want.
3. To choose the number of separate images in your animation, click the Frames arrow.
The specified number of frames appears in the Frames box.
12-991
Animating plots
your animation.
To customize the underlying plot:
· For contour plot animation, select Options->Contour from the main menu bar.
· For deformed plot animation, select Options->Deformed from the main menu bar.
· For symbol plot animation, select Options->Symbol from the main menu bar.
2. From the dialog box that appears, select the plot mode-dependent customization options that you
want. For more information, see ``Customizing your plots,'' Section 23.3.4.
3. Set the plot mode-independent customization options you want by selecting the View->View
Options, View->Viewport Annotations, or View->ODB Display Options.
· For scale factor animation, choose the single step and frame to be animated by selecting
Result->Frame.
· For time history animation, choose the steps to be animated by selecting Options->Animation
and then clicking Time History.
You can choose to save all or just selected canvas objects (viewports and annotations). Viewports that
you save can be in any plot mode (for example, deformed, X-Y, animation). For viewports currently in
12-992
Animating plots
the animation plot mode ABAQUS/CAE saves all frames of the animation, starting with the first
frame; it does not matter whether the animation is playing at the time you perform the save. If you save
multiple viewports containing animations, ABAQUS/CAE saves them all as a single image-based
animation. ABAQUS/CAE synchronizes multiple animations on the file by repeating the last frame of
any animations that have fewer frames than the others.
To save animations:
1. Produce one or more time history or scale factor animations. For more information, see
``Producing and customizing an object-based animation, '' Section 34.2.
a. Click the Capture button to save All Canvas Objects (the default) or Selected Canvas
Objects.
4. Use the Settings field to specify the name and format of your animation file:
a. Click Select to filter and browse file names, or enter the file name of your choice in the
File name field. For more information, see ``Using file selection dialog boxes,'' Section
6.3.7.
b. Click the Format button to choose either QuickTime (the default) or AVI format for your
file. To learn more about these format options, see ``Choosing the animation file format,''
Section 34.3.2.
12-993
Animating plots
2. Click the Format button to select QuickTime or AVI format and to make additional format options
available.
The format and options buttons change according to the format you select.
3. To select additional format options, click the AVI Options or QuickTime Options button.
The AVI Options or QuickTime Options dialog box appears.
4. In the options dialog box, choose one of the following methods to specify the size (in pixels) of the
animation image:
· Click Use size on screen to use the size of the image on the screen. (ABAQUS/CAE
indicates the current image size in the options dialog box.) This method is the default.
· Click Use settings below to set the width or height; then enter the value of your choice in the
Width or Height field. You specify only one dimension; ABAQUS/CAE computes the other
dimension to maintain the aspect ratio of the canvas objects.
5. In the options dialog box, specify whether your files should be compressed (run length encoded) or
uncompressed (raw).
· For QuickTime format, click the Compression button to choose either Raw (24 bits/pixel) or
Rle (24 bits/pixel). Rle (24 bits/pixel) compression is a form of run length encoding. This is a
lossless compression method causing no image degradation.
· For AVI format, click the Compression button to choose either Rle (8 bits/pixel), Raw (8
bits/pixel), or Raw (32 bits/pixel) . Choosing Rle (8 bits/pixel) compression or Raw (8
bits/pixel) can result in a loss of colors.
12-994
Animating plots
1. Choose one of the following methods to access the movie player utility:
b. Use the dialog box to filter, browse, and select the animation file to play. For more
information, see ``Using file selection dialog boxes,'' Section 6.3.7.
c. Click OK to dismiss the dialog box and open the animation file.
The ABAQUS movie player utility appears, displaying the first frame of the animation file.
2. On the lower left of the movie player window, click the left-most control arrow to begin playback.
12-995
Animating plots
step through your animation. The available options and controls are nearly identical whether you play
an object-based (time history or scale factor) animation within ABAQUS/CAE or an image-based file
animation using the ABAQUS movie player utility. For object-based animations one additional option
is available: you can display or suppress status information while the animation is playing.
This section explains how to control animation playback. The following topics are covered:
You can use these controls to stop your animation, to step forward or backward through the animation
images, to step to the first or last image in the animation sequence, and to resume playback.
To stop, restart, or step through an animation:
1. Locate the movie player controls on the left side of the prompt area.
2. Click the movie player controls to execute the functions you want. The controls are listed below in
the order in which they appear in the prompt area, starting with the left-most arrow.
Play Resumes play. When your animation is playing, the control
arrow on the Play button is green.
Stop Stops play. When your animation is stopped, the control
arrow on the Play button is black.
First image Stops play and displays the first image in the animation
sequence.
Previous image Stops play and steps to the previous image in the animation
sequence.
Next image Stops play and steps to the next image in the animation
sequence.
Last image Stops play and displays the last image in the animation
sequence.
12-996
Animating plots
2. To control the playback speed of your animation, drag the Frame rate slider to the rate that you
want.
· Click Loop to play the images in order from the first to the last, repeatedly.
· Click Swing to play the images from the first to the last and then in reverse order from the last
back to the first, repeatedly.
12-997
Animating plots
· the Step and Frame (plot number within the step) of each image contained in your time history
animation.
You cannot customize the content or appearance of the counter, other than to turn it off entirely.
The step and increment associated with each animation step and frame are given by the state block. All
of the images in a scale factor animation are based on a single step and frame. For more information on
customizing the state block, see ``Customizing the state block,'' Section 38.3.
To show the animation frame counter:
2. Toggle Show frame counter to display or suppress animation frame count information.
12-998
Generating tabular data reports
1. From the main menu bar, select Report->XY or Report->Field Output. The Report XY Data or
Report Field Output dialog box becomes available.
2. Use the options to customize the report content, format, and destination.
1. From the main menu bar, select Tools->Query, then click Apply in the dialog box that appears.
The Probe Values dialog box appears.
2. Move the cursor to probe the model or X-Y plot in the current viewport.
13-999
Generating tabular data reports
3. To select and accumulate values of interest in the Selected Probe Values table in the Probe
Values dialog box, click mouse button 1 while probing.
4. When you have finished, click Write to File to access the report file options and to generate the
report.
· The X-Y data objects or field output variables to include in the report. See ``Selecting report data,''
Section 35.3.
· The probe values to include in the report. See Chapter 31, "Querying and probing."
· The file name to which the report is written. See ``Specifying your report file name,'' Section 35.4.
· The layout and width of the report. See ``Controlling report layout and width,'' Section 35.5.
· How field output or probe values are sorted. For field output, see ``Sorting field output data,''
Section 35.6; for probe values, see ``Entering tabular data,'' Section 6.3.5.
· The format and significant digits of report values. See ``Formatting report values,'' Section 35.7.
· Whether or not to include minimum and maximum value summaries or column totals. See
``Reporting data values, minimums, maximums, and totals,'' Section 35.8.
To learn how to control the contents of a tabular report of probe values, see Chapter 31, "Querying and
probing."
13-1000
Generating tabular data reports
2. Select the X-Y data objects to include in your report from the list of available data objects. By
default, all previously saved X-Y data objects are listed. Choose one of the following options to
adjust the contents of this list:
· Click All XY data to browse all previously saved X-Y data objects.
· Click XY plot in current viewport to browse only those X-Y data objects included in the X-Y
data plot in the current viewport.
3. To limit the list for easier selection, type a filter pattern into the Name filter field, and press the
[Enter] key to apply the filter. Click the Tip button to the right of the text field to display
information about how to construct a filter.
ABAQUS/CAE lists only those X-Y data objects that meet your specification.
4. From the list of X-Y data object names and descriptions, select one or more data objects to include
in your report. For more information on selecting multiple items in dialog boxes, see ``Selecting
multiple items in lists,'' Section 6.3.8.
To generate your report, configure any desired customization options on the Setup page, which is also
in the XY Report dialog box; and click Apply. When you have finished, click Cancel to close the
dialog box.
13-1001
Generating tabular data reports
such as displacement, whereas for element-based variables such as stress, extrapolation and averaging
must be carried out to obtain the nodal values. The following table summarizes which output positions
can be reported, depending on what position was used when the variable was saved to the output
database:
Report Position
Output
Integration Element Unique
Database Centroid
point Nodal Nodal
Position
Integration Yes Yes Yes Yes
Point
Centroid No Yes Yes Yes
Element No No Yes Yes
Nodal
Unique Nodal No No No Yes
For information on selecting the section point locations at which to report beam and shell section point
variables, see ``Selecting field output section points, '' Section 35.3.3.
To select field output report data:
2. Click the Position arrow to reveal possible positions at which to list variables for your selection;
then choose the desired position. Multiple variables can be combined in a single table only if they
are reported at the same position.
The list of variables is refreshed to show only those that can be reported at the selected
position.
3. Select the field output variables to include in your report using either the check box next to each
variable in the list (this method is the default) or the Edit text field at the bottom of the page.
Note: You must use the check box method if you want to specify an individual section point at which to report values.
2. To select a variable and all of its components, click that variable's check box.
3. To choose among the individual components of a variable, click the arrow next to that
variable's check box to list its components; then click individual component check boxes
to select them.
13-1002
Generating tabular data reports
2. In the Edit text field, enter the names of the variables and components to include in your
report. To be valid, a variable must be available on the output database and reportable at
the current position.
To generate your report, configure the remaining options on the Setup page, which is also in the
Report Field Output dialog box; then click Apply. When you have finished, click Cancel to close the
dialog box.
2. Use the check box method to select beam or shell element section variables.
3. At the Section point label at the bottom of the dialog box, do one of the following:
· click Single to indicate that you will select one section point at which to report values.
If you have selected at least one element section point variable, the section point Settings
button becomes available.
13-1003
Generating tabular data reports
5. Click OK to apply your section point selections and to close the Field Report Section Point
Settings dialog box.
To generate your report, configure the remaining options on the Setup page, which is also in the
Report Field Output dialog box; then click Apply. When you have finished, click Cancel to close the
dialog box.
2. To select a file name using the standard file browser, click Select.
The Select XY Report File, Select Field Report File, or Select Probe Report File dialog box
appears. Use the dialog to filter and browse existing files. For more information on using this
dialog box, see ``Using file selection dialog boxes,'' Section 6.3.7. When you are finished, click
OK to close the dialog box.
3. Type into the Name field the name of the file to which your report is to be written.
13-1004
Generating tabular data reports
4. Toggle Append to file to append this report to the current contents (if any) of the file you have
specified. When Append to file is off, existing file contents will be overwritten.
To generate your report, configure the remaining options in the dialog box; then click Apply (for X-Y
or field output reports) or OK (for probe values reports). When you have finished, click Cancel to
close the dialog box.
13-1005
Generating tabular data reports
· Select Single table for all X-Y data (or Single table for all field ouput variables) to
combine all of the selected data objects into a single table.
For X-Y data reports, toggle Interpolate between X values (if necessary) on if you want
ABAQUS to compute missing points. When this option is toggled off, missing points (if any)
appear as ``No Value'' in the table.
· Select Separate table for each X-Y data (or Separate table for each field ouput variable)
if you want each of the selected data objects to appear in its own table.
· Select Specify to limit the table's width. Then, in the Specify text field, enter the maximum
number of characters that can appear along the width of the table.
To generate your report, configure the remaining options in the dialog box; then click Apply (for X-Y
or field output reports) or OK (for probe values reports). When you have finished, click Cancel to
close the dialog box.
13-1006
Generating tabular data reports
35.3.2.) The table has one column for each field output variable you have selected, and additional
columns to identify the origin of the field output; for example, if your table includes unique nodal
quantities ABAQUS/CAE provides a Node Label (node number) column.
For information on sorting the data in a tabular report of probe values, see ``Entering tabular data,''
Section 6.3.5.
To sort field output report data:
To generate your report, configure the remaining options in the dialog box; then click Apply. When
you have finished, click Cancel to close the dialog box.
Automatic
Very large values and very small values are expressed in scientific format. All remaining
values are expressed with no exponent and using the specified number of significant digits.
Engineering
Values greater than or equal to 1000 (or values less than or equal to 0.001) are expressed as a
number ranging from 1 to 999 that is multiplied by 10 to the nth power, where n is a product
of 3 (for example, 20.5E+03 or 17.76E+06). All remaining values are expressed using the
specified number of significant digits.
Scientific
All values are expressed as a number between 1 and 10 that is multiplied by an appropriate
13-1007
Generating tabular data reports
2. In the Number of significant digits text field, enter the number of significant digits of your
choice.
You can also click the arrows next to the Number of significant digits text field until the desired
number appears.
3. Click the Number Format button, and select the number format of your choice from the list that
appears.
To generate your report, configure the remaining options in the dialog box; then click Apply (for X-Y
or field output reports) or OK (for probe values reports). When you have finished, click Cancel to
close the dialog box.
13-1008
Generating tabular data reports
For tabular reports of probe values, ABAQUS/CAE always includes the actual data values in the
report. You can include or suppress column minimum and maximum value summaries and column
totals for any columns in which such values would be meaningful.
To report data values, minimums, maximums, and column totals:
2. For X-Y data or field output reports you must choose one or more of the following items to include
in your report:
· Toggle XY data or Field output to include the actual X-Y data or field output values,
respectively. Toggling this option off results in a report that consists of only the column total
or min/max data you request.
· Toggle Column min/max to include a summary of the minimum and maximum value
occurring in each column.
To generate your report, configure the remaining options in the dialog box; then click Apply (for X-Y
or field output reports) or OK (for probe values reports). When you have finished, click Cancel to
close the dialog box.
13-1009
Displaying a subset of your model
14-1010
Displaying a subset of your model
Replace
Use the Replace operator to replace the current viewport contents with your selection.
Add
Use the Add operator to add your selection to the current viewport contents.
Remove
Use the Remove operator to remove your selection from the current viewport contents. If your
selection includes one or more elements or surfaces, the nodes connected to those items are
also removed, provided that you have not specifically operated to include those nodes in the
display group.
Intersect
Use the Intersect operator to display only those items common to your selection and the
display in the current viewport. Only viewport items of the same type as your selection are
affected by this operation. For example, if your selection includes elements, the operation
applies only to elements in the current viewport; surfaces currently displayed (if any) are not
affected.
Either
Use the Either operation to display only model components that are either in your selection or
in the current viewport but not in both.
14-1011
Displaying a subset of your model
Tip: You can also access the display group manager using the uppermost tool in the
toolbox.
2. Click the appropriate buttons on the right side of the manager to perform the display group
operation of your choice.
3. Click Dismiss to close the dialog box when you are done.
Tip: You can also create a display group by clicking the uppermost tool in the toolbox.
The Create Display Group dialog box appears. While you are creating a display group, all other
functions are dimmed in both the Tools->Display Group menu and the Display Group Manager.
14-1012
Displaying a subset of your model
necessary.
3. Select the specific elements, nodes, or surfaces on which to operate by first choosing a selection
method and then--if necessary--specifying the elements, nodes, or surfaces.
· Element sets, Node sets, or Surface sets to specify elements, nodes, or surfaces by
set name.
ABAQUS refreshes the item list at the right. If this list is empty, there are no items
that meet your selection criteria.
· Pick from viewport to specify elements or nodes by picking them directly from the
viewport.
The Selection field appears with the text (None) to indicate that no elements or nodes
have been picked.
· Result value to specify elements, nodes, or surfaces containing results within a given
range of values.
The current variable to be filtered is displayed at the top right side of the dialog box,
and the result value options appear.
· All elements, All nodes, or All surfaces to choose all elements, nodes, or surfaces.
No further item specification is necessary. (Highlighting of the display group in the
viewport does not occur if you choose All elements, All nodes, or All Surfaces or if
you select the default model.)
· To specify element, node, or surface sets, select one or more set names from the item
list. (For more information, see ``Selecting multiple items in lists,'' Section 6.3.8.) If
your output database contains many sets, you can use the filter to reduce the number
of set names displayed. Click the Tip button next to the Filter field to see examples of
valid filtering syntax. Verify your selection by toggling Highlight items in viewport.
· To specify elements or nodes by picking them directly from the viewport, click Edit
Selection. Select elements for display group or Select nodes for display group
appears in the prompt area.
Select one or more elements or nodes from the viewport (for more information see
Chapter 9, "Selecting objects within the viewport"). The elements or nodes are
highlighted in the viewport.
14-1013
Displaying a subset of your model
Click Done in the prompt area when you have finished. The text next to Selection in
the Create Display Group dialog box changes to (Picked) to indicate that you have
selected elements or nodes.
· To specify element or node labels, first select the name of the part instance for which
you are creating a display group from the list in the Part instance field. Type into the
Labels field a list of element or node numbers separated by commas or a range of
numbers such as 1:4. Verify your selection by clicking Highlight Items in Viewport .
· To specify result values to be used as criteria for the display group, first select the
variable to be filtered. The current variable is displayed at the top right side of the
dialog box. To select a new result variable, click Field Output. The Field Output
dialog box appears. You can specify the Output Variable, the Invariant, and the
Component. See ``Selecting the field output to display,'' Section 24.3, for more
information on selecting the result variable.
Choose from the list of filtering methods in the Result values field.
- If you select Inside bounds or Outside bounds , the Upper bound and Lower
bound fields are available. Enter values for the upper and lower bounds of the
range of results.
- If you select Above value or Below value , the Value field is available. Enter a
value above or below which the results should fall.
Highlighting of the display group in the viewport does not occur for elements, nodes,
or surfaces specified by filtering result values. If you choose a range of a values for
which no elements (or nodes or surfaces) exist, a warning message will appear when
you click Replace stating the applied operation has resulted in an empty display
group.
Note: The bounds for filtering based on element, nodal, or surface output
variables are always based on the values of a variable at nodes. Therefore,
element- and surface-based output quantities are extrapolated (and possibly
averaged) at nodes before comparing them against the user-defined bounds. The
nodal averaging settings in the Field Output dialog box determine how element-
and surface-based variables are calculated at the nodes. For example, consider a
case where elements are filtered based on Mises stress using the default nodal
averaging threshold of 75%. After extrapolation to the nodes, the values are
averaged according to this threshold. This conditional averaging may result in
several distinct values of Mises stress at the node based on contributions from the
various elements to which the node belongs. Any element whose Mises stress
contribution falls within the user-defined bounds is included in the display group.
Every element (or node or surface) in the model is used in the filtering process,
regardless of the current active display group in the model.
14-1014
Displaying a subset of your model
4. From the icons in the bottom portion of the dialog box, click the desired Boolean operation.
ABAQUS carries out the selected Boolean operation on the model components you have selected
in the dialog box and the contents of the current viewport.
5. If the effect of the Boolean operation is not desired, you can undo the most recent operation using
the Undo button at the bottom of the dialog box.
When you click the Undo button, it changes to Redo. When you click the Redo button, ABAQUS
reapplies the most recent Boolean operation.
6. Repeat steps beginning with Step 2 as needed to produce the desired display group.
7. To save the display group, click Save As; then enter a name in the dialog box that appears. You
can plot, edit, copy, rename, or delete saved display groups. In addition, you can use a saved
display group to display the same subset of different models in different viewports.
Display groups that you save are available only during the current session.
To save a display group:
14-1015
Displaying a subset of your model
The Create Display Group or Display Group Editor dialog box appears, according to your
selection.
2. Use the dialog box to select the model components of interest. For more information, see
``Creating a display group,'' Section 36.2.1, or ``Editing a display group,'' Section 36.2.3.
3. After you select model components but before you apply a Boolean operator in the Create Display
Group dialog box, you can save either the selection in the dialog box or the contents of the current
viewport. To do so:
a. From the lower left corner of the dialog box, click Save As.
The Save Display Group As dialog box appears.
· Only the current selection to save the selection in the dialog box.
· Items in the viewport prior to selection to save the contents of the current viewport.
4. After you apply a Boolean operator, you can save the contents of the current viewport. To do so:
a. From the lower left corner of the dialog box, click Save As.
The Save Display Group As dialog box appears.
5. Click Dismiss to close the Create Display Group or Edit Display Group dialog box.
14-1016
Displaying a subset of your model
display group is similar to creating a display group: in both cases you select model components and
then apply Boolean operations on your selection and the contents of the current viewport. Certain
display groups can be highlighted in the viewport.
When you select a display group to edit, the contents of the current viewport update to show the
selected display group. You use the display in the current viewport to determine the model components
in the group you are editing; you cannot list the model components. When you are finished editing, all
viewports that use the display group will be updated.
To edit a display group:
The Edit Display Group dialog box appears. While you are editing a display group, all other
functions are dimmed in both the Tools->Display Group menu and the Display Group Manager.
3. Select the specific elements, nodes, or surfaces on which to operate by first choosing a selection
method and then--if necessary--specifying the elements, nodes, or surfaces.
· Element sets, Node sets, or Surface sets to specify elements, nodes, or surfaces by
set name.
ABAQUS refreshes the item list at the right. If this list is empty, there are no items
that meet your selection criteria.
· Pick from viewport to specify elements or nodes by picking them directly from the
viewport.
The Selection field appears with the text (None) to indicate that no elements or nodes
have been picked.
14-1017
Displaying a subset of your model
· Result value to specify elements, nodes, or surfaces containing results within a given
range of values.
The current variable to be filtered is displayed at the top right side of the dialog box,
and the result value options appear.
· All elements, All nodes, or All surfaces to choose all elements, nodes, or surfaces.
No further item specification is necessary. (Highlighting of the display group in the
viewport does not occur if you choose All elements, All nodes, or All surfaces or if
you select the default model.)
· To specify element, node, or surface sets, select one or more set names from the item
list. If your output database contains many sets, you can use the filter to reduce the
number of set names displayed. Click the Tip button to see examples of the syntax
used in the Filter field. Verify your selection by toggling Highlight items in
viewport .
· To specify elements or nodes by picking them directly from the viewport, click Edit
Selection. Select elements for display group or Select nodes for display group
appears in the prompt area.
Select one or more elements or nodes from the viewport (for more information see
Chapter 9, "Selecting objects within the viewport"). The elements or nodes are
highlighted in the viewport.
Click Done in the prompt area when you have finished. The text next to Selection in
the Create Display Group dialog box changes to (Picked) to indicate that you have
selected elements or nodes.
· To specify element or node labels, first select the name of the part instance for which
you are creating a display group from the list in the Part instance field. Type into the
Labels field a list of element or node numbers separated by commas or a range of
numbers such as 1:4. Verify your selection by clicking Highlight Items in Viewport .
· To specify result values to be used as criteria for the display group, first select the
variable to be filtered. The current variable is displayed at the top right side of the
dialog box. To select a new result variable, click Field Output. The Field Output
dialog box appears. You can specify the Output Variable, the Invariant, and the
Component. See ``Selecting the field output to display,'' Section 24.3, for more
information on selecting the result variable.
Choose from the list of filtering methods in the Result values field.
- If you select Inside bounds or Outside bounds , the Upper bound and Lower
bound fields are available. Enter values for the upper and lower bounds of the
14-1018
Displaying a subset of your model
range of results.
- If you select Above value or Below value , the Value field is available. Enter a
value above or below which the results should fall.
Highlighting of the display group in the viewport does not occur for elements, nodes,
or surfaces specified by filtering result values. If you choose a range of a values for
which no elements (or nodes or surfaces) exist, a warning message will appear when
you click Replace stating the applied operation has resulted in an empty display
group.
Note: The bounds for filtering based on element, nodal, or surface output
variables are always based on the values of a variable at nodes. Therefore,
element- and surface-based output quantities are extrapolated (and possibly
averaged) at nodes before comparing them against the user-defined bounds. The
nodal averaging settings in the Field Output dialog box determine how element-
and surface-based variables are calculated at the nodes. For example, consider a
case where elements are filtered based on Mises stress using the default nodal
averaging threshold of 75%. After extrapolation to the nodes, the values are
averaged according to this threshold. This conditional averaging may result in
several distinct values of Mises stress at the node based on contributions from the
various elements to which the node belongs. Any element whose Mises stress
contribution falls within the user-defined bounds is included in the display group.
Every element (or node or surface) in the model is used in the filtering process,
regardless of the current active display group in the model.
4. From the icons in the bottom portion of the dialog box, click the desired Boolean operation.
ABAQUS carries out the selected Boolean operation on the model components you have selected
in the dialog box and the contents of the current viewport.
5. If the effect of the Boolean operation is not desired, you can undo the most recent operation using
the Undo button at the bottom of the dialog box.
When you click the Undo button it changes to Redo. When you click the Redo button, ABAQUS
reapplies the most recent Boolean operation.
6. Repeat steps beginning with Step 2 as needed to produce the desired display group.
7. Click OK to save the updated display group and to close the Edit Display Group dialog box.
14-1019
Displaying a subset of your model
2. From the menu that appears, select the display group that you want to plot.
Tip: You can also use the Display Group Manager to plot a display group. From the main
menu bar, select Tools->Display Group->Manager to display the manager. Select the display
group you want to plot, and click Plot from the buttons on the right side of the manager.
The model plot in the current viewport changes to show the selected display group.
· The Copy, Rename, and Delete items listed under the Tools->Display Group menu on the main
menu bar.
The Copy, Rename, and Delete items contain submenus listing all the display groups you have
saved during the session.
· The Display Group Manager dialog box. The Display Group Manager dialog box contains
functions identical to those listed under the Tools->Display Group menu on the main menu bar
but with a convenient browser that lists all the display groups you have saved during the session.
To display the Display Group Manager dialog box, select Tools->Display Group->Manager
from the main menu bar.
Note: If you try to delete a display group that is shown in multiple viewports, ABAQUS/CAE
warns that the display groups in those viewports will be reset to the default model.
14-1020
Displaying a subset of your model
2. From the main menu bar, select Tools->Display Group->Plot. Select the display group to plot
from the menu that appears.
ABAQUS plots the display group in the current viewport. ABAQUS plots only the components in
the display group that are valid for the current model.
14-1021
Displaying a subset of your model
2. From the main menu bar, select Tools->Display Group->Edit. Select the display group to edit
from the menu that appears.
The Edit Display Group dialog box appears.
3. Select the desired model components, and apply the desired Boolean operations.
During the editing process, the results of any Boolean operations appear only in the current
viewport.
14-1022
Customizing model display
Render style
Render style is the style in which ABAQUS/CAE displays your model. Render style is a plot
mode-dependent option; that is, you control it separately for undeformed, deformed, contour,
symbol, and material orientation plots. Render style choices include wireframe, filled, hidden,
and lightsource-shaded, although some choices are not applicable to every plot mode. For
more information, see ``Customizing render style, translucency, and fill color,'' Section 37.2.
15-1023
Customizing model display
Edge style is the line style and thickness of element and surface edges; edge visibility is the
extent to which ABAQUS/CAE displays these edges. Edge style and visibility options are plot
mode-dependent. For more information, see ``Customizing element and surface edges,''
Section 37.3.
Model shape
For contour, symbol, and material orientation plots you can choose to display your results on
the undeformed or the deformed model shape. Additional model shape options allow you to
scale coordinates, scale deformations, and shrink elements and surfaces. All model shape
options are plot mode-dependent. For more information, see ``Customizing model shape,''
Section 37.5.
Boundary conditions
You can change the visibility of symbols representing boundary conditions applied during the
analysis. For more information, see ``Displaying boundary conditions,'' Section 37.8.
15-1024
Customizing model display
· Curved Lines & Faces to control how quadratic and cubic element edges and faces are
displayed. For more information, see ``Refining curved edges and faces,'' Section 37.9.2.
· Elements with No Results to control the color of elements having no results (for
example, rigid surfaces) in contour plots. For more information, see ``Coloring elements
with no results,'' Section 37.9.3.
Figure 37-1 Model showing render style options. From left to right: the wireframe, filled, hidden, and
lightsource-shaded render styles.
15-1025
Customizing model display
Wireframe
Displays model edges; both interior and exterior edges are potentially visible. Wireframe plots
produce a frame-like visual effect in which model faces are not displayed. Wireframe is the
most rapidly drawn render style.
Filled
Displays model faces ``painted'' in a uniform color. Filled plots produce a solid rather than
frame-like appearance in which only exterior faces are visible.
Hidden
Displays a wireframe plot in which edges obscured by the model are not visible. Hidden plots
produce a solid rather than frame-like appearance.
Shaded
Displays a filled plot in which a light source appears to be directed at the model. Shaded plots
produce a highly three-dimensional visual effect.
1. Locate the Render Style options for the plot mode (undeformed, deformed, contour, symbol, or
material orientation) that you want to customize.
From the main menu bar, select Options->plot mode; then click the Basic tab in the dialog box
that appears. The Render Style options become available.
2. From the Render Style list, click the render style you want.
Tip: You can also select the render style by clicking the wireframe , hidden , filled
, or shaded icons located in the toolbar, and then clicking in the desired viewport.
Note:
· Contour plots support the filled and shaded render styles only.
· Symbol and material orientation plots support the wireframe and shaded render styles only.
· Symbol and material orientation plots in the shaded render style automatically activate translucency at a default value of
0.3.
15-1026
Customizing model display
1. Locate the Translucency options for the plot mode (undeformed, deformed, contour, symbol, or
material orientation) that you want to customize.
From the main menu bar, select Options->plot mode. Click the Other tab in the dialog box that
appears; then click the Translucency tab. The Translucency options appear.
15-1027
Customizing model display
1. Locate the fill color options for the plot mode (undeformed, deformed, symbol, or material
orientation) that you want to customize.
From the main menu bar, select Options->plot mode; then click the Color & Style tab in the
dialog box that appears.
Note: Fill color applies to shaded plots only, since the filled render style is not
supported for these plot modes.
a. To reveal the color options, click the fill color arrow, which is labeled Fill color in
filled/shaded plots or Fill color in shaded plots.
3. Toggle Allow color code selections to override options in this dialog off to display all
elements in the fill color specified above. Toggle it on to override this color using individual item
color selections. The default is on. For more information, see ``Coloring individual elements and
surfaces,'' Section 37.4.
15-1028
Customizing model display
Since fill color is plot mode-dependent, the fill color changes to reflect your specifications in plots
of the current mode only.
Your changes are saved for the duration of the session and will affect all subsequent plots in this
mode.
1. Locate the Visible Edges options for the plot mode (undeformed, deformed, contour, symbol, or
material orientation) that you want to customize.
From the main menu bar, select Options->plot mode; then click the Basic tab in the dialog box
that appears. The Visible Edges options are on the right side of the Basic page.
2. To choose the element and surface edges you want to display, click one of the following:
All
Displays all element and surface edges. To see element edges on the interior of the model,
15-1029
Customizing model display
you must also set the render style to wireframe. This choice is not available for contour
plots.
Exterior
Displays only edges on the exterior of the model.
Feature
Displays only edges on the exterior of the model that are calculated to be feature edges.
Feature edges lie between elements that have normals that differ by more than the
``feature angle.'' The feature angle is set in the View->ODB Display Options->General
dialog; for more information, see ``Defining model feature edges,'' Section 37.3.2.
Free
Displays only edges that belong to a single element. Free edge display is particularly
useful for locating potential holes or cracks in your mesh.
None
Suppresses the display of all edges. This choice is available only for plots rendered using
lightsource-shading.
15-1030
Customizing model display
angle. Larger angles will reduce the number of feature edges; conversely, smaller angles will cause
more edges to be visible. The default is 20°. The setting of the feature angle applies to all plot modes.
In Figure 37-3 the plot on the left shows feature edges when the feature angle is set to 0°, the plot in
the middle shows feature edges on the same model but with the feature angle set to 5°, and the plot on
the right shows the model with the feature angle set to 20°.
Figure 37-3 Plots showing feature angles of 0°, 5°, and 20°.
15-1031
Customizing model display
1. Locate the edge color options for the plot mode (undeformed, deformed, contour, symbol, or
material orientation) that you want to customize.
From the main menu bar, select Options->plot mode; then click the Color & Style tab in the
dialog box that appears.
2. Choose the color of the element and surface edges for wireframe and hidden render style plots and
line-type contours. (For all of these plots ABAQUS/CAE does not display model faces.)
a. Click the arrow, which will be labeled either Edges in wireframe/hidden plots , Edges
in wireframe plots , or In line plots, to reveal the color options.
3. Choose the color of the element and surface edges for filled and shaded render style plots and
banded- and quilt-type contour plots. (For all of these plots ABAQUS/CAE displays model faces.)
a. Click the arrow, which will be labeled either Edges in filled/shaded plots , Edges in
shaded plots, or In banded/quilt plots, to reveal the color options.
4. Toggle Allow color code selections to override options in this dialog off to display all edges
in the color specified above. Toggle it on to override this color using color code selections. The
default is on. This option is not available for contour plots.
15-1032
Customizing model display
1. Locate the Edge Attributes options for the plot mode (undeformed, deformed, contour, symbol, or
material orientation) that you want to customize.
From the main menu bar, select Options->plot mode; then click the Color & Style tab in the
dialog box that appears.
15-1033
Customizing model display
The Edge Attributes options are at the bottom of the Color & Style page.
· ``Understanding how individual element and surface coloring interacts with model coloring, ''
Section 37.4.1
15-1034
Customizing model display
Render style
In the wireframe and hidden render styles, ABAQUS/CAE displays only element and surface
edges. If the current plot mode uses the wireframe or hidden render style, ABAQUS/CAE
applies the individual item color to those edges.
In the filled and shaded render styles, ABAQUS/CAE displays element and surface edges as
well as element faces and filled surfaces. If the current plot mode uses the filled or shaded
render style, ABAQUS/CAE applies the individual item color to the element faces and filled
surfaces or to the element and surface edges.
In the filled and shaded render styles, line-type elements (such as beams) are treated as if their
lines are faces. In the filled and shaded render styles, ABAQUS/CAE applies the individual
item color to the lines representing such an element.
15-1035
Customizing model display
Tip: You can also access the Color Code options using the tool in the toolbox.
ABAQUS refreshes the Selection Method at the bottom of the dialog box and the item list at the
right. If you select Default Model, these fields are empty and no further item specification is
necessary.
· Pick from viewport to specify elements by picking them directly from the viewport.
The Selection field appears with the text (None) to indicate that no elements have
been picked.
15-1036
Customizing model display
· Result value to specify elements or surfaces containing results within a given range
of values.
The current variable to be filtered is displayed at the top right side of the dialog box,
and the result value options appear.
· To specify element or surface sets, select one or more set names from the item list.
(For more information, see ``Selecting multiple items in lists,'' Section 6.3.8.) If your
output database contains many sets, you can use the filter to reduce the number of set
names displayed. Click Tip next to the Filter field to see examples of valid filtering
syntax. Verify your selection by toggling Highlight items in viewport.
· To specify elements by picking them directly from the viewport, click Edit Selection.
Select elements for display group appears in the prompt area.
Select one or more elements from the viewport (for more information see Chapter 9,
"Selecting objects within the viewport"). The elements are highlighted in the
viewport.
Click Done in the prompt area when you have finished. The text next to Selection in
the Color Code dialog box changes to (Picked) to indicate that you have selected
elements.
· To specify element labels, first select the name of the part instance for which you are
selecting elements from the list in the Part instance field. Type into the Labels field
a list of element numbers separated by commas or a range of numbers such as 1:4.
Verify your selection by clicking Highlight Items in Viewport .
· To specify result values to be used as criteria for an element or surface set, first select
the variable to be filtered. The current variable is displayed at the top right side of the
dialog box. To select a new result variable, click Field Output. The Field Output
dialog box appears. You can specify the Output Variable, the Invariant, and the
Component. See ``Selecting the field output to display,'' Section 24.3, for more
information on selecting the result variable.
Choose from the list of filtering methods in the Result values field.
- If you select Inside bounds or Outside bounds , the Upper bound and Lower
bound fields are available. Enter values for the upper and lower bound of the
15-1037
Customizing model display
range or results.
- If you select Above value or Below value , the Value field is available. Enter a
value above or below which the results should fall.
Highlighting of the items in the viewport does not occur for elements or surfaces
specified by filtering result values.
Note: The bounds for filtering based on element, nodal, or surface output
variables are always based on the values of a variable at nodes. Therefore,
element- and surface-based output quantities are extrapolated (and possibly
averaged) at nodes before comparing them against the user-defined bounds. The
nodal averaging settings in the Field Output dialog box determine how element-
and surface-based variables are calculated at the nodes. For example, consider a
case where elements are filtered based on Mises stress using the default nodal
averaging threshold of 75%. After extrapolation to the nodes, the values are
averaged according to this threshold. This conditional averaging may result in
several distinct values of Mises stress at the node based on contributions from the
various elements to which the node belongs. Any element whose Mises stress
contribution falls with the user-defined bounds is included in the display group.
Every element (or surface) in the model is used in the filtering process, regardless
of the current active display group in the model.
a. Click the arrow next to the items you wish to color: Edges in wireframe/hidden plots ,
Edges in filled/shaded plots , or Fill color in filled/shaded plots.
15-1038
Customizing model display
· ``Choosing the underlying model shape for contour, symbol, and material orientation plots, ''
Section 37.5.1
Figure 37-5 Contour plots on the undeformed and the deformed shape.
1. Locate the Shape options for the plot mode that you want to customize.
From the main menu bar, select Options->Contours, Options->Symbols, or Options->Material
Orientation. Click the Shape tab in the dialog box that appears; the Shape options become
available.
15-1039
Customizing model display
how to customize deformation scale factors, see ``Scaling deformations,'' Section 37.5.2.
Figure 37-6 Contour plots showing default and magnified deformation values.
Deformation scaling is plot mode-dependent; that is, you control it separately for deformed plots, for
contour plots on the deformed shape, for symbol plots on the deformed shape, and for material
orientation plots on the deformed shape. The default scaling is a uniform factor of 1.00 for
large-displacement analyses. For small-deformation analyses--for example, a perturbation
analysis--ABAQUS/CAE scales the deformation such that the maximum deformation is 10% of the
largest model dimension.
15-1040
Customizing model display
1. Locate the Deformation Scale Factor options for the plot mode (deformed, contour, or symbol)
that you want to customize.
· Click Auto-compute to request that ABAQUS automatically compute and uniformly apply a
single scale factor to all X-, Y-, and Z-components of deformation values.
· Click Uniform to specify and uniformly apply a single scale factor to all X-, Y-, and
Z-components of deformation values.
When Uniform is on, a Value specification box becomes available. Click the Value box, and
enter your scale factor.
· Click Nonuniform to specify individual scale factors to be applied to the X-, Y-, and
Z-components of deformation values.
When Nonuniform is on, X-, Y-, and Z-component scale factor specification boxes become
available. For each component you want to scale, click the component ( X, Y, or Z) scale factor
box and enter your scale factor.
15-1041
Customizing model display
Scaling and shrinking options are plot mode-dependent; that is, you control them separately for
undeformed, deformed, contour, symbol, and material orientation plots.
To scale or shrink your model:
1. Locate the Scaling options for the plot mode (undeformed, deformed, contour, symbol, or material
orientation) that you want to customize.
From the main menu bar, select Options->plot mode; then click the Other tab in the dialog box
that appears. Click the Scaling tab; the Scaling options appear.
2. Toggle Shrink elements to request or suppress shrinking each element about its centroid.
a. When Shrink elements is on, the shrink Percentage slider becomes available.
3. Toggle Scale coordinates to request or suppress model scaling by nodal coordinate X-, Y-, and
Z-directions.
a. When Scale coordinates is on, scale factors become available. Click the X, Y, and Z
boxes to enter scale factors for the X, Y, and Z nodal coordinates, respectively.
15-1042
Customizing model display
1. Locate the font options for the plot mode (undeformed, deformed, contour, symbol, or material
orientation) that you want to customize.
From the main menu bar, select Options->plot mode; then click the Labels tab in the dialog box
that appears. The font options are at the top of the Labels page.
3. Use the Select Font dialog box to set the font properties that you want.
4. When you have set the desired font properties, click OK.
15-1043
Customizing model display
Element labels are plot mode-dependent; that is, you control them separately for undeformed,
deformed, contour, symbol, and material orientation plots. Toggle Show element labels to display or
suppress element labels and to choose their color.
To customize element labels:
15-1044
Customizing model display
1. Locate the element label options for the plot mode (undeformed, deformed, contour, symbol, or
material orientation) that you want to customize.
From the main menu bar, select Options->plot mode; then click the Labels tab in the dialog box
that appears.
a. Click the Color arrow to reveal the element label color options.
15-1045
Customizing model display
Face labels are plot mode-dependent; that is, you control them separately for undeformed, deformed,
contour, symbol, and material orientation plots. Toggle Show face labels to display or suppress face
labels and to choose their color.
To customize face labels:
1. Locate the face label options for the plot mode (undeformed, deformed, contour, symbol, or
material orientation) that you want to customize.
From the main menu bar, select Options->plot mode; then click the Labels tab in the dialog box
that appears.
a. Click the Color arrow to reveal the face label color options.
15-1046
Customizing model display
Node labels are plot mode-dependent; that is, you control them separately for undeformed, deformed,
contour, symbol, and material orientation plots. Toggle Show node labels to display or suppress node
labels and to choose their color.
To customize node labels:
1. Locate the node label options for the plot mode (undeformed, deformed, contour, symbol, or
material orientation) that you want to customize.
From the main menu bar, select Options->plot mode; then click the Labels tab in the dialog box
that appears.
a. Click the Color arrow to reveal the node label color options.
15-1047
Customizing model display
Node symbols are plot mode-dependent; that is, you control them separately for undeformed,
deformed, contour, symbol, and material orientation plots. Toggle Show node symbols to display or
suppress node symbols and to choose their color, type, and size.
To customize node symbols:
1. Locate the node symbol options for the plot mode (undeformed, deformed, contour, symbol, or
material orientation) that you want to customize.
From the main menu bar, select Options->plot mode; then click the Labels tab in the dialog box
that appears.
15-1048
Customizing model display
When Show node symbols is on, the node symbol color, type, and size options become
available.
a. Click the Color arrow to reveal the node symbol color options.
4. Choose the type (circle, square, triangle, etc.) of the node symbols:
a. Click the Symbol button to reveal the node symbol type options.
a. Click the Size button to reveal the node symbol size options.
15-1049
Customizing model display
1. Locate the Normals options for the plot mode (undeformed or deformed) of interest.
From the main menu bar, select Options->plot mode; then click the Normals tab in the dialog
box that appears.
3. In the area of the dialog box labeled Colors, select the colors in which you want the different types
of normals to appear.
a. Click the Length menu button, and select the arrow length of your choice. The default
selection is Medium.
b. Click the Thickness menu button, and select the arrow thickness of your choice.
c. Click the Arrowhead menu button, and select the arrowhead style of your choice.
15-1050
Customizing model display
modeled sector of a cyclic symmetric structure or "sweep" the sector to see a specified portion of the
entire model. (For more information on cyclic symmetric structures, see ``Analysis of models that
exhibit cyclic symmetry,'' Section 7.7.3 of the ABAQUS/Standard User's Manual.) In addition, you can
view two-dimensional models (or three-dimensional cylindrical rigid surfaces) as planar or extrude
them to a specified depth, producing a three-dimensional visual effect. Sweeping and extruding are
particularly useful for displaying contour plots of two-dimensional elements and contact surfaces.
Axisymmetric analytical rigid surfaces can be rotated about an axis (swept), as can the following
elements: ACAXn, CAXn, CAXAn, CGAXn, DCAXn, DCCAXn, DSAXn, FAXn, MAXn, MGAXn,
RAXn, SAXn, and SAXAn. Models that contain three-dimensional axisymmetric analytical rigid
surfaces or CAXA elements are swept by default (the default start angle, end angle, and number of
sectors vary depending on the model type). If the model contains both analytical rigid surfaces and
CAXA elements, only the CAXA elements are swept by default.
Cyclic symmetric models are not swept by default.
You can extrude analytical rigid surfaces and all of the planar, two-dimensional solid elements in the
ABAQUS library along the Z-direction. For a list of these elements, see ``Two-dimensional solid
element library,'' Section 14.1.3 of the ABAQUS/Standard User's Manual and Section 13.1.2 of the
ABAQUS/Explicit User's Manual.
Figure 37-12 shows an axisymmetric planar model in a planar view (left) and the same model with an
axisymmetric sweep angle of 90° and 10 sweep sectors (right).
Figure 37-13 shows the original modeled sector of a cyclic symmetric fan (left) and sectors 1-4 of the
swept model (right).
Figure 37-13 Cyclic symmetric model: single sector and swept view of multiple sectors.
15-1051
Customizing model display
Figure 37-14 shows a two-dimensional planar model in a planar view (left) and the same model
displayed with an extrusion depth of 0.1 (right).
3. Specify the sweep angle by typing a number (in degrees) in the Sweep from field (the default is
0°) and a number (in degrees) in the To field (the default is 360° for all models except CAXA
15-1052
Customizing model display
ABAQUS/CAE sweeps the two-dimensional model counterclockwise about the axis of rotation
from the first specified angle to the second.
4. Specify the number of segments to use along the circumferential direction when sweeping by
typing a positive integer in the Number field or by clicking on the arrows next to the field. The
default number of segments used varies depending on the model type.
The angle between the segments is updated automatically in the dialog box. As you increase the
number of segments, curves in the model appear smoother (the angle between them decreases).
However, a smaller number of segments plots faster.
3. Click the arrow next to the Sector selection field to choose from the following available sweep
methods:
By Number
This is the default sweep method. The total number of sectors in the model is given in the
dialog box. You can specify which of these sectors should be displayed by typing positive
integers between 1 and the total number of sectors (delimited by commas) in the Sectors
field. The sectors are numbered counterclockwise from the original sector.
ABAQUS/CAE displays only the specified sectors (whether or not they are adjacent).
By Angle
The sector angle (the angle between each sector) is given in the dialog box. You can
15-1053
Customizing model display
specify the sweep angle in increments of the sector angle by typing a number (in degrees)
in the Sweep from field (the default is 0°) and a number (in degrees) in the To field (the
default is the sector angle). Both numbers should be divisible by the sector angle.
Tip: You can also use the arrows next to the text fields to specify the angles.
ABAQUS/CAE sweeps the two-dimensional model about the axis of rotation by the
number of degrees you specify. If you enter a sweep angle that is not divisible by the
sector angle, ABAQUS/CAE rounds up to the next number that is.
All Sectors
If you choose this sweep method, all sectors will be displayed; in other words, the model
will be swept 360° about the axis of rotation.
3. Specify the depth of the extrusion by typing a positive number (in model units) in the Depth field.
The default depth is 1.0.
ABAQUS/CAE extends your model the specified number of units in the negative z-direction.
Use the view manipulation rotation tool to view the extruded model in three dimensions.
15-1054
Customizing model display
If the current plot mode is Symbol, the model is extruded as specified, but the symbols appear only
on the original planar model faces.
Figure 37-15 Model plotted with different refinement levels (extra coarse and extra fine).
Note: As the refinement level increases, the display performance will decrease. The Medium
setting should produce acceptable results for most models.
15-1055
Customizing model display
box that appears. The Curved Lines & Faces options are at the top of the General page.
3. In the refinement list, click the level you want. Extra fine produces the smoothest curves but may
slow plotting; conversely, coarse refinement gives a rough appearance but plots most quickly.
The refinement level you specify appears on the Refinement Level button.
15-1056
Customizing model display
In this case the color gray was selected for elements with no results. The die elements appear gray
because the die is a rigid surface for which no stress results exist.
For contour plots, if you have set the render style to shaded, the translucency options apply only to
those elements with no results.
To color elements with no results:
3. In the color list, click the color name that you want.
The color you specify appears in the Color box.
15-1057
Customizing viewport annotations
For information on the view triad, see ``Customizing the view triad,'' Section 8.2.
You can display or suppress legends for all plot modes, and you can customize the following:
16-1058
Customizing viewport annotations
· the appearance of the legend background (the rectangular area behind the legend).
You cannot directly specify the size of the legend. However, by varying the size of the text font you
can increase or decrease the legend's size.
The content of the legend depends on the plot mode and on plot mode-specific options such as the
number of contour intervals or the style of X-Y curves. For more information on contour plot legend
content, see ``Understanding contour plotting,'' Section 27.1; for information on X-Y plot legend
content, see ``Customizing the X-Y plot legend,'' Section 30.6.3.
To customize the legend:
3. To display or suppress a box outlining the legend, toggle Show bounding box . This ``bounding
box'' visually separates the legend from the underlying plot.
4. To display or suppress the minimum and maximum values associated with X-Y plots, toggle Show
min/max values.
5. To choose the number of digits shown in legend values, click the Decimal places arrow. Legend
values appear in exponential format, and the Decimal places option controls the number of digits
to the right of the decimal point. Larger Decimal places values require more display space.
The specified number of digits appears in the Decimal places box.
b. Use the Select Font dialog box to choose the font characteristics you want. For more
information, see ``Customizing fonts,'' Section 6.3.6.
c. When you are done, click OK to implement your changes and to close the Select Font
dialog box.
16-1059
Customizing viewport annotations
· The name of the output database (from the name of the analysis job).
· The description of the model (from the first line of the *HEADING option in the input file).
You can display or suppress the title block for all plot modes, and you can display or suppress the
appearance of a box bounding the title block. In addition, you can control the position, text font, and
text color of the title block, and the appearance of the title block background. You cannot directly
specify the size of the title block. However, by varying the size of the text font you can increase or
decrease the title block's size. The content of the title block is fixed and cannot be customized.
To customize the title block:
16-1060
Customizing viewport annotations
2. To display or suppress title blocks for all plot modes, toggle Show title block .
When Show title block is on, the title block options become available.
3. To display or suppress a box outlining the title block, toggle Show bounding box . This
``bounding box'' visually separates the title block from the underlying plot.
4. Establish the position of the upper left corner of the title block.
To control the X- or Y -position, click the % Viewport X or % Viewport Y boxes, respectively.
Enter the positions you want as a percentage of the total width of the current viewport.
b. Use the Select Font dialog box to choose the font characteristics you want. For more
information, see ``Customizing fonts,'' Section 6.3.6.
c. When you are done, click OK to implement your changes and to close the Select Font
dialog box.
16-1061
Customizing viewport annotations
information includes step, frame, results variables, deformation magnification factor, eigenmode, and
eigenvalue, as applicable.
You can display or suppress the state block for all plot modes, and you can display or suppress the
appearance of a box bounding the state block. In addition, you can control the position, text font, and
text color of the state block, and the appearance of the state block background. You cannot directly
specify the size of the state block. However, by varying the size of the text font you can increase or
decrease the state block's size. The content of the state block is fixed and cannot be customized.
To customize the state block:
2. To display or suppress state blocks for all plot modes, toggle Show state block .
When Show state block is on, state block options become available.
3. To display or suppress a box outlining the state block, toggle Show bounding box . This
``bounding box'' visually separates the state block from the underlying plot.
4. Establish the position of the upper left corner of the state block.
To control the X- or Y -position, click the % Viewport X or % Viewport Y boxes, respectively.
Enter the positions you want as a percentage of the total width of the current viewport.
b. Use the Select Font dialog box to choose the font characteristics you want. For more
information, see ``Customizing fonts,'' Section 6.3.6.
c. When you are done, click OK to implement your changes and to close the Select Font
dialog box.
16-1062
Customizing viewport annotations
· Legend: Control the appearance and position of the legend and whether minimum and
maximum values are shown.
· Title Block: Control the appearance and position of the title block.
· State Block: Control the appearance and position of the state block.
2. Use the tabs in the dialog box to customize viewport annotations for all plots in the current
viewport.
16-1063
Special graphical symbols
17-1064
Special graphical symbols
17-1065
Using ABAQUS/CAE toolsets
0-1066
The Amplitude toolset
· ``Amplitude curves,'' Section 19.1.2 of the ABAQUS/Standard User's Manual and Section 18.1.2
of the ABAQUS/Explicit User's Manual
1-1067
The Amplitude toolset
· ``Amplitude curves,'' Section 19.1.2 of the ABAQUS/Standard User's Manual and Section 18.1.2
of the ABAQUS/Explicit User's Manual
2. In the Name field, enter a name for the amplitude. For information on naming objects, see ``Using
basic dialog box components,'' Section 6.3.1.
3. From the Type list, select the type of amplitude that you want to create and then click Continue.
The amplitude editor appears in which you can enter all of the data necessary to define the
amplitude. For special table editing options or to read data from an ASCII file, press mouse button
3. (For more information, see ``Entering tabular data,'' Section 6.3.5.)
1-1068
The Amplitude toolset
· ``Amplitude curves,'' Section 19.1.2 of the ABAQUS/Standard User's Manual and Section 18.1.2
of the ABAQUS/Explicit User's Manual
1-1069
The Datum toolset
To extrude a blind cut into the curved surface, you need to sketch the profile on a plane that is tangent
to the curved surface. The desired plane does not exist, but you can create one with the Datum toolset
and sketch on the resulting plane. The datum plane and the resulting cut feature are shown in Figure
41-2.
2-1070
The Datum toolset
You can create datum points, axes, planes, and reference coordinate systems. You can use a reference
coordinate system to orient a boundary condition or an equation constraint. ABAQUS/CAE does not
generate meshes on datum geometry, and datum geometry has no effect on the analysis of your model;
it is simply a convenience to help you construct complex geometry. You should use the Partition
toolset if you want to add geometry to the model itself, such as a vertex along an edge or a plane
through a cell.
You create a datum by defining it with respect to existing geometry (such as vertices, planes, and
edges) or to other datum geometry. You can create a datum on a part in the Part module or the Property
module or on an assembly in other modules. For example, you can define a datum axis that passes
through two selected points of a part in the Part module, and you can use the axis to align instances of
the part in the Assembly module. A datum is a feature; and, like all features, it can be edited, deleted,
suppressed, and resumed. Similarly, a datum is regenerated when the assembly or part is regenerated.
2-1071
The Datum toolset
You choose the type of datum to create--point, axis, plane, or coordinate system ( CSYS)--from the
buttons in the Type region at the top of the dialog box. The Method list changes to reflect the datum
you create. Select the desired datum tool from the Method list, and follow the prompts in the prompt
area to create the datum. ``An overview of datum creation techniques,'' Section 41.4, provides an
overview of the methods available for each type of datum. More information on creating datum
geometry on parts and assemblies is provided in ``Using the Datum toolset in the Part module,'' Section
14.11.1, and ``Using datum geometry in the Assembly module,'' Section 16.5.1.
You can also access the Datum toolset from the module toolbox; Figure 41-4 shows the hidden icons
for all the datum tools in the module toolboxes.
To see a brief tooltip containing a definition of each datum tool, hold the mouse over the tool for a
moment. For information on using toolboxes and selecting hidden icons, see ``Using toolboxes that
contain hidden icons,'' Section 6.4.2.
2-1072
The Datum toolset
A datum is a useful construction aid in the feature-based modeling process and is a feature itself. As a
result, you can use the Feature Manipulation toolset to delete, suppress, and resume a datum.
ABAQUS/CAE regenerates a datum along with the part or assembly, taking into account any changes
to underlying geometry. You can edit any numerical parameters that define a datum; for example, the
X-, Y-, and Z-coordinates used to define a datum point. However, a datum is always defined by the
same underlying geometry you selected when you created it; if you need to define the datum using
different geometry, you must delete the datum and create a new one.
When you modify a feature, you should be aware of any parent-child relationships between your datum
and the modified feature. For example, consider Figure 41-5, which shows a datum axis passing
through the midpoint of two arcs.
The midpoints of the arcs that define the location of the datum axis are parents of the datum axis. If
you modify the part, ABAQUS/CAE regenerates the datum axis so that it still passes through the two
midpoints, as shown in Figure 41-6.
2-1073
The Datum toolset
· When prompted to select a point, ABAQUS/CAE highlights the points you can select. You can
select one of the following:
- A datum point
· When prompted to select an edge, you can select an edge or a datum axis.
· When prompted to select a face, you can select a face or a datum plane.
For more information, see ``Selecting and unselecting individual objects, '' Section 9.2.1.
The following topics are covered:
· ``An overview of the methods for creating a datum point,'' Section 41.4.1
· ``An overview of the methods for creating a datum axis,'' Section 41.4.2
· ``An overview of the methods for creating a datum plane,'' Section 41.4.3
· ``An overview of the methods for creating a datum coordinate system,'' Section 41.4.4
2-1074
The Datum toolset
Enter coordinates
Enter the X-, Y-, and Z-coordinates of the datum point, as shown in Figure 41-7. For detailed
instructions, see ``Creating a datum point by entering its coordinates,'' Section 41.5.1.
2-1075
The Datum toolset
Figure 41-10 Positioning a datum point a specified distance from two edges.
Use parameter
Select an edge on the model, and enter the location of the datum point in the form of a
parameter value that represents a percentage of the edge length. An arrow along the edge
indicates the direction of increasing parameter value from the start vertex (corresponding to an
edge parameter value of zero) to the end vertex (corresponding to a value of one), as shown in
Figure 41-11. For detailed instructions, see ``Creating a datum point by specifying an edge
parameter,'' Section 41.5.5.
2-1076
The Datum toolset
point where the plane intersects a line that is normal to it and passing through the selected
point, as shown in Figure 41-12. The datum point also marks the shortest distance between the
selected point and the selected face. For detailed instructions, see ``Creating a datum point by
projecting a point on a face,'' Section 41.5.6.
2-1077
The Datum toolset
Principal axis
Select one of the three principal axes with which the datum axis must be colinear, as shown in
Figure 41-14. For detailed instructions, see ``Creating a datum axis along a principal axis,''
Section 41.6.1.
Figure 41-14 Defining a datum axis as one of the three principal axes.
Intersection of 2 planes
Select two non-parallel planar surfaces. ABAQUS/CAE creates the datum axis where the two
planes (or extensions of the two planes) intersect, as shown in Figure 41-15. For detailed
instructions, see ``Creating a datum axis along the intersection of two planes, '' Section 41.6.2.
Straight edge
Select a straight edge on the model with which the datum axis must be colinear, as shown in
Figure 41-16. For detailed instructions, see ``Creating a datum axis along a straight edge,''
Section 41.6.3.
2-1078
The Datum toolset
2 points
Select any two points on the model through which the datum axis must pass, as shown in
Figure 41-17. For detailed instructions, see ``Creating a datum axis through two points,''
Section 41.6.4.
Axis of cylinder
Select a cylindrical face on the model. ABAQUS/CAE creates a datum axis that lies along the
axis of the cylindrical face, as shown in Figure 41-18. For detailed instructions, see ``Creating
a datum axis along the axis of a cylinder,'' Section 41.6.5.
2-1079
The Datum toolset
3 points on circle
Select three points on the model that define a circle. ABAQUS/CAE creates a datum axis
along the axis of the circle, as shown in Figure 41-21. For detailed instructions, see ``Creating
a datum axis running along the axis of a circle defined by three points, '' Section 41.6.8.
Figure 41-22 Defining a datum axis by rotating an edge through a specified angle.
2-1080
The Datum toolset
Figure 41-23 Creating a datum plane by offsetting from one of the three principal planes.
A positive value indicates an offset in the positive direction along the axis normal to the
selected plane; for example, along the X-axis normal to the Y-Z plane. For detailed
instructions, see ``Creating a datum plane offset from a principal plane,'' Section 41.7.1.
2-1081
The Datum toolset
3 points
Select three points through which the datum plane must pass, as shown in Figure 41-25. For
detailed instructions, see ``Creating a datum plane passing through three points, '' Section
41.7.3.
2-1082
The Datum toolset
Figure 41-27 Creating a datum plane by selecting a point and a normal edge.
Figure 41-29 Defining a datum plane by rotating a face through a specified angle.
For detailed instructions, see ``Creating a datum plane by rotating an existing face through a
specified angle,'' Section 41.7.7.
2-1083
The Datum toolset
Default
Position a rectangular, cylindrical, or spherical datum coordinate system at the same location
as the part or assembly coordinate system, as shown by the example involving a rectangular
system in Figure 41-30. For detailed instructions, see ``Creating a default datum coordinate
system,'' Section 41.8.1.
Figure 41-30 Positioning a rectangular datum coordinate system at the default part or
assembly coordinate system.
Figure 41-31 Positioning a rectangular datum coordinate system by offsetting from another
coordinate system.
2-1084
The Datum toolset
3 points
Select three points on the model that define the rectangular, cylindrical, or spherical
coordinate system. In the case of a rectangular system, the first point defines the origin, the
second point defines the X-axis, and the X-Y plane passes through the second and third points,
as shown in Figure 41-32. For detailed instructions, see ``Creating a datum coordinate system
defined by three points,'' Section 41.8.3.
Figure 41-32 Positioning a rectangular datum coordinate system by selecting three points.
2 lines
Select two edges that define the rectangular, cylindrical, or spherical coordinate system. In the
case of a rectangular system, the first edge defines the X-axis and the X-Y plane passes through
the second edge, as shown in Figure 41-33. For detailed instructions, see ``Creating a datum
coordinate system defined by two lines,'' Section 41.8.4.
Figure 41-33 Positioning a rectangular datum coordinate system by selecting two edges.
2-1085
The Datum toolset
· ``Creating a datum point at an offset from a selected point, '' Section 41.5.2
· ``Creating a datum point at a specified distance from two edges,'' Section 41.5.4
Tip: You can also create a datum point using the tool, located in the module toolbox.
For a diagram of the datum tools in the toolbox, see ``Using the Datum toolset,'' Section 41.2.
2. From the list of types at the top of the dialog box, choose Point.
The Method list indicates the methods you can use to create a datum point.
3. From the Method list, select Enter coordinates and click OK.
4. In the text field that appears in the prompt area, enter the X-, Y-, and Z-coordinates of the datum
point you want to create. If the datum is associated with the assembly, the coordinates you provide
2-1086
The Datum toolset
are relative to the assembly's global coordinate system. If the datum is associated with a part, the
coordinates are relative to the part's coordinate system. If you are unsure of the location or
orientation of the part's coordinate system, first create a default coordinate system at the origin of
the part. For more information, see ``Creating a default datum coordinate system,'' Section 41.8.1.
The datum point appears. You can modify the coordinates of the datum point by selecting
Feature->Edit from the main menu bar and selecting the datum.
· ``An overview of the methods for creating a datum point,'' Section 41.4.1
Detailed instructions for creating a datum point at an offset from a selected point:
Tip: You can also create a datum point using the tool, located in the module toolbox.
For a diagram of the datum tools in the toolbox, see ``Using the Datum toolset,'' Section 41.2.
2. From the list of types at the top of the dialog box, choose Point.
The Method list indicates the methods you can use to create a datum point.
3. From the Method list, select Offset from point and click OK.
4. From the part or assembly in the current viewport, select a point. The point can be either a vertex,
2-1087
The Datum toolset
5. In the text field that appears in the prompt area, enter the X-, Y-, and Z-coordinates of the offset
from the selected point.
The datum point appears. You can modify the coordinates of the offset by selecting Feature->Edit
from the main menu bar and selecting the datum.
· ``An overview of the methods for creating a datum point,'' Section 41.4.1
Detailed instructions for creating a datum point midway between two points:
Tip: You can also create a datum point using the tool, located in the module toolbox.
For a diagram of the datum tools in the toolbox, see ``Using the Datum toolset,'' Section 41.2.
2. From the list of types at the top of the dialog box, choose Point.
The Method list indicates the methods you can use to create a datum point.
3. From the Method list, select Midway between 2 points and click OK.
2-1088
The Datum toolset
4. From the part or assembly in the current viewport, select two points. The points can be either a
vertices, datum points, midpoints, or arc centers.
The datum point appears. You cannot modify a datum point created with this method; you must
delete the old point and create a new one.
· ``An overview of the methods for creating a datum point,'' Section 41.4.1
Detailed instructions for creating a datum point by specifying the distance from two edges:
Tip: You can also create a datum point using the tool, located in the module toolbox.
For a diagram of the datum tools in the toolbox, see ``Using the Datum toolset,'' Section 41.2.
2. From the list of types at the top of the dialog box, choose Point.
The Method list indicates the methods you can use to create a datum point.
3. From the Method list, select Offset from 2 edges and click OK.
4. From the part or assembly in the current viewport, select the plane on which to create the datum
point.
2-1089
The Datum toolset
5. Select a straight edge on the specified plane and enter the distance of the datum point from this
edge.
6. Select a second straight edge on the plane and enter the distance of the datum point from this edge.
The datum point appears. You can modify the position of the datum point by selecting
Feature->Edit from the main menu bar and modifying the distance from the datum to each edge.
· ``An overview of the methods for creating a datum point,'' Section 41.4.1
Tip: You can also create a datum point using the tool, located in the module toolbox.
For a diagram of the datum tools in the toolbox, see ``Using the Datum toolset,'' Section 41.2.
2. From the list of types at the top of the dialog box, choose Point.
The Method list indicates the methods you can use to create a datum point.
3. From the Method list, select Use parameter and click OK.
2-1090
The Datum toolset
4. From the part or assembly in the current viewport, select the edge on which the datum point will
be positioned.
An arrow appears on the selected edge indicating the direction of increasing parameter value.
5. In the text field in the prompt area, enter the value of the edge parameter.
The datum point appears. You can modify the position of the datum point by selecting
Feature->Edit from the main menu bar and modifying the value of the edge parameter.
· ``An overview of the methods for creating a datum point,'' Section 41.4.1
Tip: You can also create a datum point using the tool, located in the module toolbox.
For a diagram of the datum tools in the toolbox, see ``Using the Datum toolset,'' Section 41.2.
2-1091
The Datum toolset
2. From the list of types at the top of the dialog box, choose Point.
The Method list indicates the methods you can use to create a datum point.
3. From the Method list, select Project point on face and click OK.
4. From the part or assembly in the current viewport, select a point. The point can be either a vertex,
a datum point, a midpoint, or an arc center.
5. Select a plane on which to project the point. The plane can be a planar face or a datum plane.
The datum point appears. You cannot modify a datum point created with this method; you must
delete the old point and create a new one.
· ``An overview of the methods for creating a datum point,'' Section 41.4.1
Tip: You can also create a datum point using the tool, located in the module toolbox.
For a diagram of the datum tools in the toolbox, see ``Using the Datum toolset,'' Section 41.2.
2-1092
The Datum toolset
2. From the list of types at the top of the dialog box, choose Point.
The Method list indicates the methods you can use to create a datum point.
3. From the Method list , select Project point on line and click OK.
4. From the part or assembly in the current viewport, select a point. The point can be either a vertex,
a datum point, a midpoint, or an arc center.
· ``An overview of the methods for creating a datum point,'' Section 41.4.1
· ``Creating a datum axis along the intersection of two planes, '' Section 41.6.2
· ``Creating a datum axis normal to a plane and passing through a point, '' Section 41.6.6
· ``Creating a datum axis parallel to a line and passing through a point, '' Section 41.6.7
· ``Creating a datum axis running along the axis of a circle defined by three points, '' Section 41.6.8
· ``Creating a datum axis by rotating an existing edge through a specified angle,'' Section 41.6.9
2-1093
The Datum toolset
Tip: You can also create a datum axis using the tool, located in the module toolbox.
For a diagram of the datum tools in the toolbox, see ``Using the Datum toolset,'' Section 41.2.
2. From the list of types at the top of the dialog box, choose Axis.
The Method list indicates the methods you can use to create a datum axis.
3. From the Method list, select Principal axis and click OK.
4. Select the principal X-, Y-, or Z-axis through which your datum axis must pass.
The datum axis appears. You cannot modify a datum axis created with this method; you must
delete the old axis and create a new one.
· ``An overview of the methods for creating a datum axis,'' Section 41.4.2
2-1094
The Datum toolset
Detailed instructions for creating a datum axis along the intersection of two planes:
Tip: You can also create a datum axis using the tool, located in the module toolbox.
For a diagram of the datum tools in the toolbox, see ``Using the Datum toolset,'' Section 41.2.
2. From the list of types at the top of the dialog box, choose Axis.
The Method list indicates the methods you can use to create a datum axis.
3. From the Method list, select Intersection of 2 planes and click OK.
· ``An overview of the methods for creating a datum axis,'' Section 41.4.2
2-1095
The Datum toolset
Tip: You can also create a datum axis using the tool, located in the module toolbox.
For a diagram of the datum tools in the toolbox, see ``Using the Datum toolset,'' Section 41.2.
2. From the list of types at the top of the dialog box, choose Axis.
The Method list indicates the methods you can use to create a datum axis.
3. From the Method list, select Straight edge and click OK.
4. From the part or assembly in the current viewport, select a straight edge.
The datum axis appears. You cannot modify a datum axis created with this method; you must
delete the old axis and create a new one.
· ``An overview of the methods for creating a datum axis,'' Section 41.4.2
2-1096
The Datum toolset
Tip: You can also create a datum axis using the tool, located in the module toolbox.
For a diagram of the datum tools in the toolbox, see ``Using the Datum toolset,'' Section 41.2.
2. From the list of types at the top of the dialog box, choose Axis.
The Method list indicates the methods you can use to create a datum axis.
4. From the part or assembly in the current viewport, select two points. The points can be either
vertices, datum points, midpoints, or arc centers.
The datum axis appears. You cannot modify a datum axis created with this method; you must
delete the old axis and create a new one.
· ``An overview of the methods for creating a datum axis,'' Section 41.4.2
2-1097
The Datum toolset
Detailed instructions for creating a datum axis along the axis of a cylinder:
Tip: You can also create a datum axis using the tool, located in the module toolbox.
For a diagram of the datum tools in the toolbox, see ``Using the Datum toolset,'' Section 41.2.
2. From the list of types at the top of the dialog box, choose Axis.
The Method list indicates the methods you can use to create a datum axis.
3. From the Method list, select Axis of cylinder and click OK.
4. From the part or assembly in the current viewport, select a a cylindrical or conical face.
The datum axis appears. You cannot modify a datum axis created with this method; you must
delete the old axis and create a new one.
· ``An overview of the methods for creating a datum axis,'' Section 41.4.2
2-1098
The Datum toolset
Detailed instructions for creating a datum axis normal to a plane and passing through a point:
Tip: You can also create a datum axis using the tool, located in the module toolbox.
For a diagram of the datum tools in the toolbox, see ``Using the Datum toolset,'' Section 41.2.
2. From the list of types at the top of the dialog box, choose Axis.
The Method list indicates the methods you can use to create a datum axis.
3. From the Method list, select Normal to plane, thru point and click OK.
4. From the part or assembly in the current viewport, select a planar face.
5. From the part or assembly in the current viewport, select a point. The point can be either a vertex,
a datum point, a midpoint, or an arc center.
The datum axis appears. You cannot modify a datum axis created with this method; you must
delete the old axis and create a new one.
· ``An overview of the methods for creating a datum axis,'' Section 41.4.2
2-1099
The Datum toolset
ABAQUS/CAE creates a datum axis that is parallel to the edge and passes through the point.
Detailed instructions for creating a datum axis parallel to a line and passing through a point:
Tip: You can also create a datum axis using the tool, located in the module toolbox.
For a diagram of the datum tools in the toolbox, see ``Using the Datum toolset,'' Section 41.2.
2. From the list of types at the top of the dialog box, choose Axis.
The Method list indicates the methods you can use to create a datum axis.
3. From the Method list, select parallel to line, thru point and click OK.
5. From the part or assembly in the current viewport, select a point. The point can be either a vertex,
a datum point, a midpoint, or an arc center.
The datum axis appears. You cannot modify a datum axis created with this method; you must
delete the old axis and create a new one.
· ``An overview of the methods for creating a datum axis,'' Section 41.4.2
2-1100
The Datum toolset
Detailed instructions for creating a datum axis along the axis of a circle defined by three
points:
Tip: You can also create a datum axis using the tool, located in the module toolbox.
For a diagram of the datum tools in the toolbox, see ``Using the Datum toolset,'' Section 41.2.
2. From the list of types at the top of the dialog box, choose Axis.
The Method list indicates the methods you can use to create a datum axis.
3. From the Method list, select Three points on circle and click OK.
4. From the part or assembly in the current viewport, select three points. The points can be either
vertices, datum points, midpoints, or arc centers.
The datum axis appears.You cannot modify a datum axis created with this method; you must
delete the old axis and create a new one.
· ``An overview of the methods for creating a datum axis,'' Section 41.4.2
2-1101
The Datum toolset
Detailed instructions for creating a datum axis by rotating an edge through a specified angle:
Tip: You can also create a datum axis using the tool, located in the module toolbox.
For a diagram of the datum tools in the toolbox, see ``Using the Datum toolset,'' Section 41.2.
2. From the list of types at the top of the dialog box, choose Axis.
The Method list indicates the methods you can use to create a datum axis.
3. From the Method list, select Rotate from line and click OK.
4. From the part or assembly in the current viewport, select an edge or a datum axis to rotate.
5. The technique for specifying the the rotation depends on the modeling space of the part or
assembly:
2-1102
The Datum toolset
1. Select a vertex or datum point at the center of rotation. You can also use the text box that
appears in the prompt area to enter the precise coordinates of the center of rotation.
2. In the text box in the prompt area, enter the angle of rotation. A positive angle indicates a
counterclockwise rotation about the Z-axis.
The datum axis appears.
2. In the text box that appears in the prompt area, type the angle of rotation.
The datum axis appears.
You can modify the angle of rotation by selecting Feature->Edit from the main menu bar and
selecting the datum axis. If you change the sign of the angle, ABAQUS/CAE reverses the direction
of rotation.
· ``An overview of the methods for creating a datum axis,'' Section 41.4.2
· ``Creating a datum plane passing through three points, '' Section 41.7.3
· ``Creating a datum plane through a line and a point, '' Section 41.7.4
· ``Creating a datum plane passing through a point and normal to an edge, '' Section 41.7.5
· ``Create a datum plane midway between two points and normal to the line connecting the two
points,'' Section 41.7.6
2-1103
The Datum toolset
· ``Creating a datum plane by rotating an existing face through a specified angle,'' Section 41.7.7
Detailed instructions for creating a datum plane offset from a principal plane:
Tip: You can also create a datum plane using the tool, located in the module toolbox.
For a diagram of the datum tools in the toolbox, see ``Using the Datum toolset,'' Section 41.2.
2. From the list of types at the top of the dialog box, choose Plane.
The Method list indicates the methods you can use to create a datum plane.
3. From the Method list, select Offset from principal plane and click OK.
4. From the buttons in the prompt area, select the principal plane.
5. In the text field in the prompt area, enter the offset from the selected principal plane. The offset
can be positive or negative. A positive value offsets the datum plane along the positive principal
axis normal to the selected plane.
The datum plane appears. You can modify the position of the datum plane by selecting
Feature->Edit from the main menu bar and modifying the value of the offset.
· ``An overview of the methods for creating a datum plane,'' Section 41.4.3
2-1104
The Datum toolset
Detailed instructions for creating a datum plane offset from a selected plane:
Tip: You can also create a datum plane using the tool, located in the module toolbox.
For a diagram of the datum tools in the toolbox, see ``Using the Datum toolset,'' Section 41.2.
2. From the list of types at the top of the dialog box, choose Plane.
The Method list indicates the methods you can use to create a datum plane.
3. From the Method list, select Offset from plane and click OK.
5. From the buttons in the prompt area, select one of the following:
Enter Value
2. Click Flip to reverse the arrow, if necessary. Click OK to accept the indicated offset
direction.
3. In the text field in the prompt area, enter the offset from the selected plane. The offset can
2-1105
The Datum toolset
be positive or negative. A positive value offsets the datum plane in the direction indicated
by the arrow.
Select Point
From the part or assembly in the current viewport, select a point to define the offset from
the selected plane. The point can be either a vertex, a datum point, a midpoint, or an arc
center.
The datum plane appears. You can modify the position of the datum plane by selecting
Feature->Edit from the main menu bar and modifying the value of the offset.
· ``An overview of the methods for creating a datum plane,'' Section 41.4.3
Detailed instructions for creating a datum plane passing through three points:
Tip: You can also create a datum plane using the tool, located in the module toolbox.
For a diagram of the datum tools in the toolbox, see ``Using the Datum toolset,'' Section 41.2.
2. From the list of types at the top of the dialog box, choose Plane.
2-1106
The Datum toolset
The Method list indicates the methods you can use to create a datum plane.
4. From the part or assembly in the current viewport, select three points. The points can be either
vertices, datum points, midpoints, or arc centers.
The datum plane appears. You cannot modify a datum plane created with this method; you must
delete the old plane and create a new one.
· ``An overview of the methods for creating a datum plane,'' Section 41.4.3
Detailed instructions for creating a datum plane through a line and a point:
Tip: You can also create a datum plane using the tool, located in the module toolbox.
For a diagram of the datum tools in the toolbox, see ``Using the Datum toolset,'' Section 41.2.
2. From the list of types at the top of the dialog box, choose Plane.
The Method list indicates the methods you can use to create a datum plane.
2-1107
The Datum toolset
3. From the Method list, select Line and point and click OK.
4. From the part or assembly in the current viewport, select a straight edge.
5. From the part or assembly in the current viewport, select a point. The point can be either a vertex,
a datum point, a midpoint, or an arc center.
The datum plane appears. You cannot modify a datum plane created with this method; you must
delete the old plane and create a new one.
· ``An overview of the methods for creating a datum plane,'' Section 41.4.3
Detailed instructions for creating a datum plane passing through a point and normal to an edge:
Tip: You can also create a datum plane using the tool, located in the module toolbox.
For a diagram of the datum tools in the toolbox, see ``Using the Datum toolset,'' Section 41.2.
2. From the list of types at the top of the dialog box, choose Plane.
The Method list indicates the methods you can use to create a datum plane.
2-1108
The Datum toolset
3. From the Method list, select Point and normal and click OK.
4. From the part or assembly in the current viewport, select a point. The point can be either a vertex,
a datum point, a midpoint, or an arc center.
· ``An overview of the methods for creating a datum plane,'' Section 41.4.3
Detailed instructions for creating a datum plane midway between two points and normal to the
line connecting the two points:
Tip: You can also create a datum plane using the tool, located in the module toolbox.
For a diagram of the datum tools in the toolbox, see ``Using the Datum toolset,'' Section 41.2.
2-1109
The Datum toolset
2. From the list of types at the top of the dialog box, choose Plane.
The Method list indicates the methods you can use to create a datum plane.
3. From the Method list, select Midway between 2 points and click OK.
4. From the part or assembly in the current viewport, select two points. The points can be either
vertices, datum points, midpoints, or arc centers.
The datum plane appears. You cannot modify a datum plane created with this method; you must
delete the old plane and create a new one.
· ``An overview of the methods for creating a datum plane,'' Section 41.4.3
Detailed instructions for creating a datum plane by rotating a face through a specified angle:
2-1110
The Datum toolset
Tip: You can also create a datum plane using the tool, located in the module toolbox.
For a diagram of the datum tools in the toolbox, see ``Using the Datum toolset,'' Section 41.2.
2. From the list of types at the top of the dialog box, choose Plane.
The Method list indicates the methods you can use to create a datum plane.
3. From the Method list, select Rotate from plane and click OK.
4. From the part or assembly in the current viewport, select a face or a datum plane to rotate.
5. Select any edge or a datum axis to represent the axis of rotation. The edge or datum axis you select
for the axis of rotation does not have to be coplanar with the face or datum plane you selected to
rotate.
ABAQUS/CAE displays an arrow along the selected edge indicating the positive direction of
rotation using the right-hand rule.
6. In the text box that appears in the prompt area, type the angle of rotation.
The datum plane appears. You can modify the angle of rotation by selecting Feature->Edit from
the main menu bar and selecting the datum plane. If you change the sign of the angle,
ABAQUS/CAE reverses the direction of rotation.
· ``An overview of the methods for creating a datum plane,'' Section 41.4.3
· ``Creating a datum coordinate system at an offset from another coordinate system,'' Section 41.8.2
2-1111
The Datum toolset
Tip: You can also create a datum coordinate system using the tool, located in the
module toolbox. For a diagram of the datum tools in the toolbox, see ``Using the Datum
toolset,'' Section 41.2.
2. From the list of types at the top of the dialog box, choose CSYS.
The Method list indicates the methods you can use to create a datum coordinate system.
4. From the buttons in the prompt area, select one of the following datum coordinate systems:
· Cartesian: The X-, Y-, and Z-axes are aligned with the 1-, 2-, and 3-global axes,
respectively.
· Cylindrical: The R-, µ-, and Z-axes are aligned with the 1-, 2-, and 3-global axes,
respectively.
· Spherical: The R-, µ-, and Á-axes are aligned with the 1-, 2-, and 3-global axes,
respectively.
The datum coordinate system appears. You cannot move or rotate a datum coordinate system.
2-1112
The Datum toolset
· ``An overview of the methods for creating a datum coordinate system,'' Section 41.4.4
Detailed instructions for creating datum coordinate systems by the offset from coordinate system
method:
Tip: You can also create a datum coordinate system using the tool, located in the
module toolbox. For a diagram of the datum tools in the toolbox, see ``Using the Datum
toolset,'' Section 41.2.
2. From the list of types at the top of the dialog box, choose CSYS.
The Method list indicates the methods you can use to create a datum coordinate system.
3. From the Method list, select Offset from CSYS and click OK.
4. From the buttons in the prompt area, select one of the following datum coordinate systems:
· Cartesian: The X-, Y-, and Z-axes are aligned with the 1-, 2-, and 3-global axes,
respectively.
· Cylindrical: The R-, µ-, and Z-axes are aligned with the 1-, 2-, and 3-global axes,
respectively.
2-1113
The Datum toolset
· Spherical: The R-, µ-, and Á-axes are aligned with the 1-, 2-, and 3-global axes,
respectively.
6. From the buttons in the prompt area, select one of the following:
Enter Value
In the text field in the prompt area, enter the X-, Y-, and Z-coordinates of the offset from
the selected default coordinate system.
Select Point
From the part or assembly in the current viewport, select a point to define the offset from
the selected default coordinate system. The point can be either a vertex, a datum point, a
midpoint, or an arc center.
The datum coordinate system appears. You cannot move or rotate a datum coordinate system.
· ``An overview of the methods for creating a datum coordinate system,'' Section 41.4.4
2-1114
The Datum toolset
Detailed instructions for creating a datum coordinate system defined by three points:
Tip: You can also create a datum coordinate system using the tool, located in the
module toolbox. For a diagram of the datum tools in the toolbox, see ``Using the Datum
toolset,'' Section 41.2.
2. From the list of types at the top of the dialog box, choose CSYS.
The Method list indicates the methods you can use to create a datum coordinate system.
4. From the buttons in the prompt area, select one of the following datum coordinate systems:
· Cartesian: The X-, Y-, and Z-axes are aligned with the 1-, 2-, and 3-global axes,
respectively.
· Cylindrical: The R-, µ-, and Z-axes are aligned with the 1-, 2-, and 3-global axes,
respectively.
· Spherical: The R-, µ-, and Á-axes are aligned with the 1-, 2-, and 3-global axes,
respectively.
5. From the part or assembly in the current viewport, select a point that will define the origin of the
datum coordinate system. The point you select can be either a vertex, a datum point, a midpoint, or
an arc center.
· ``An overview of the methods for creating a datum coordinate system,'' Section 41.4.4
2-1115
The Datum toolset
Detailed instructions for creating a datum coordinate system defined by two lines:
Tip: You can also create a datum coordinate system using the tool, located in the
module toolbox. For a diagram of the datum tools in the toolbox, see ``Using the Datum
toolset,'' Section 41.2.
2. From the list of types at the top of the dialog box, choose CSYS.
The Method list indicates the methods you can use to create a datum coordinate system.
4. From the buttons in the prompt area, select one of the following datum coordinate systems:
· Cartesian: The X-, Y-, and Z-axes are aligned with the 1-, 2-, and 3-global axes,
respectively.
· Cylindrical: The R-, µ-, and Z-axes are aligned with the 1-, 2-, and 3-global axes,
respectively.
· Spherical: The R-, µ-, and Á-axes are aligned with the 1-, 2-, and 3-global axes,
respectively.
5. From the part or assembly in the current viewport, select a straight edge that will define the X- or
R-axis of the datum coordinate system.
2-1116
The Datum toolset
The datum coordinate system appears. You cannot move or rotate a datum coordinate system.
· ``An overview of the methods for creating a datum coordinate system,'' Section 41.4.4
2-1117
The Feature Manipulation toolset
Edit a feature
You can edit the features of a part only in the Part module. Any changes that you make to a
part are applied automatically to each instance of that part in the assembly. Likewise, you can
edit features of the assembly only in the Assembly and Mesh modules. For information on
restrictions that apply to editing partitions and datum geometry, see ``Understanding a datum
as a feature,'' Section 41.3, and ``Understanding partitions,'' Section 43.3.
Regenerate a feature
Regeneration is the process of recalculating model geometry after a feature of the model has
been modified. By default, ABAQUS/CAE automatically regenerates a part or assembly after
you have edited one of its features. However, you can control whether or not features are
regenerated automatically by toggling the Regenerate on OK option off or on in the Feature
Editor. For more information, see ``Editing a feature,'' Section 42.3.1.
Suppress a feature
When you work with many features in a complex model, ABAQUS/CAE allows you to
temporarily disable certain features to simplify the display or to speed regeneration. A
suppressed feature is not visible, cannot be partitioned or meshed, and is not included in the
solver input file. In addition, ABAQUS/CAE ignores all suppressed features when
regenerating a part or assembly. You can edit a suppressed feature, although your changes will
have no effect on the part or assembly until you resume the feature.
Suppressing a feature also suppresses any children of that feature. (For information on parent
3-1118
The Feature Manipulation toolset
and child features, see ``The relationship between parts and features, '' Section 14.3.1.)
Alternatively, you can make a part instance invisible to the assembly but still retain that part
instance as part of the model by selecting options in the Assembly Display Options dialog
box. For more information, see ``Controlling instance visibility,'' Section 46.9.
Resume a feature
When you resume a suppressed feature, it reappears in the display of the part or assembly and
becomes reestablished in the model. If you edited the feature when it was suppressed,
resuming the feature causes ABAQUS/CAE to regenerate the model automatically to take into
account your changes. When you resume a feature, you have the option of resuming all of its
children as well. (You cannot resume a child feature without also resuming its parent.)
Delete a feature
Deleting a feature removes the feature from the model permanently. If you delete a parent
feature, all of its children will also be deleted and cannot be recovered.
(Suppressed features and assembly constraints cannot be selected in the viewport, so you must use the
Feature List dialog box to select these types of features.) The Feature List dialog box appears when
you click Feature List in the prompt area during an operation.
The Feature List dialog box contains a list of all the features in the current module. When you select a
3-1119
The Feature Manipulation toolset
feature name from the dialog box list, that feature is highlighted in the viewport. You can select more
than one feature from the list of features when you are deleting, suppressing, or resuming features.
However, none of the Feature Manipulation toolset tools allow you to select more than one feature
directly from the viewport.
The Status column of the dialog box indicates which features are currently suppressed or have failed
to regenerate. If a feature is not valid for the current operation, the name of that feature appears in
italics and cannot be selected.
· Depth of an extrusion
· Radius of a fillet
If you cannot make the required changes with the Feature Manipulation toolset, you must delete the
feature and create a new one that incorporates the changes.
3-1120
The Feature Manipulation toolset
Tip: You can also edit a feature by clicking the tool located in the module toolbox.
2. Select a feature to modify. You can select the feature either directly from the current viewport or
from the feature list. For more information, see Chapter 9, "Selecting objects within the viewport,"
and ``The feature list,'' Section 42.2.
The feature editor appears.
· In the Parameters field, type a new value for the desired parameter.
· Select Edit Section Sketch to start the Sketcher and make the changes to your sketch. For
information on using the Sketcher, see Chapter 22, "The Sketch module."
3-1121
The Feature Manipulation toolset
Tip: You can also suppress a feature using the tool located in the module toolbox.
2. Select a feature to suppress. You can select the feature either directly from the current viewport or
from the Feature List dialog box. If you use the Feature List dialog box, you can select multiple
features to suppress. For more information, see Chapter 9, "Selecting objects within the viewport,"
and ``The feature list,'' Section 42.2.
ABAQUS/CAE highlights the selected feature(s). If you selected a feature that has child features,
ABAQUS/CAE also highlights the children.
3. In the prompt area, click Yes to suppress the feature and its children.
The suppressed features disappear from the viewport.
Tip: You can also resume a feature using the tool located in the module toolbox.
3-1122
The Feature Manipulation toolset
· Click Last Set to resume the most recently suppressed feature and all its parents.
· Click Feature List and select the feature to resume from the Feature List dialog box. If you
use the Feature List dialog box, you can select multiple features to resume.
Tip: You can also delete a feature using the tool located in the module toolbox.
2. Select a feature to delete. You can select the feature either directly from the current viewport or
from the feature list. If you use the Feature List dialog box, you can select multiple features to
resume. For more information, see Chapter 9, "Selecting objects within the viewport," and ``The
feature list,'' Section 42.2.
ABAQUS/CAE highlights the feature(s) that you selected. If you selected a feature that has child
features, ABAQUS/CAE also highlights the children.
3-1123
The Feature Manipulation toolset
Tip: You can also regenerate a feature using the tool located in the module toolbox.
2. If regeneration fails, a dialog box appears and ABAQUS/CAE issues a warning in the message
area indicating the ID of the failed feature. In this case you can choose one of the following
options:
· Click Undo Changes to return to the original part or assembly and discard all your changes.
· Click Keep Changes to continue the regeneration, suppressing those features that failed to
regenerate.
Note: Features that are suppressed as a result of the failure are resumed automatically if
you correct the cause of the failure.
3-1124
The Feature Manipulation toolset
Tip: You can also select the query tool in the toolbar.
2. From the Query dialog box, select Feature and choose one of the following options:
· To display detailed information about a single feature, select the feature to query. You can
select the feature either directly from the current viewport or from the feature list.
ABAQUS/CAE displays the following information about the selected feature:
- Status--active or suppressed
· To get brief information about all features, click List All Features in the prompt area.
ABAQUS/CAE displays a table containing each feature's ID, name, and status--active or
suppressed.
The information appears in the message area and is also written to the replay file (abaqus.rpy)
in the form of comments.
1. From the Feature menu in the main menu bar, select Edit, Suppress, Resume, or Delete.
2. In the lower right corner of the prompt area, click Feature List.
The Feature List dialog box appears.
3. In the dialog box, select a feature from the feature list and click OK.
3-1125
The Feature Manipulation toolset
If a feature is not valid for the current operation, the name of that feature appears in italics and
cannot be selected.
The feature that you select is highlighted if it is visible in the current viewport.
3-1126
The Partition toolset
You partition edges, faces, and cells by defining partitions that refer to existing geometry. You can
partition a part in either the Part module or the Property module, or you can partition an assembly in
4-1127
The Partition toolset
the modules that operate on the assembly. For example, you can partition a face of the assembly in the
Mesh module, and you can seed the resulting internal edge to refine your mesh. A partition is a feature
and, like all features, it can be edited, deleted, suppressed, resumed, and queried. Similarly, a partition
is regenerated when the assembly or a part is regenerated.
You choose the type of geometry to partition--edge, face, or cell--from the buttons in the Type region
at the top of the dialog box. The Method list changes to reflect the partitions you can create. Select the
desired partition tool from the Method list, and follow the prompts in the prompt area to create the
partition. Most of the tools allow you to partition multiple edges, faces, or cells in one operation. You
can use a combination of drag select, [Shift]+Click, and [Ctrl]+Click to select the edges, faces, or
cells to partition.
``An overview of partitioning techniques,'' Section 43.4, provides an overview of the methods
available for each type of partition. More information on creating partitions on parts and assemblies is
provided in ``Using the Partition toolset in the Part module,'' Section 14.11.3, and ``Partitioning the
assembly,'' Section 16.5.3.
You can also access the Partition toolset from the module toolbox; Figure 43-3 shows the hidden icons
for all the partition tools in the module toolboxes.
4-1128
The Partition toolset
To see a tooltip containing a short description of each partition tool, hold the mouse over the tool for a
moment. For more information, see ``Using toolboxes that contain hidden icons, '' Section 6.4.2.
Partitioning parts
Use the Partition toolset in the Part or Property module to divide a part into regions. You
might use the resulting regions in the Property module to apply section definitions, which
include cross-sectional geometry information as well as material property information.
Partitions created in the Part module and Property module are associated with the part and are
available in every instance of the part in the assembly; however, you cannot modify or delete
the partitions in a part instance.
· Gain finer control over the meshing process by adding internal edges that can be seeded.
· Subdivide complex three-dimensional regions into simpler regions that the automatic
mesh generator can mesh.
Partitions created in an assembly are associated only with the assembly, not with the original
parts, and are available in all the modules that operate on the assembly. They will not appear
in other instances of the same part, and they are not available in the Part or Property module.
4-1129
The Partition toolset
1. The user partitions a face using a line between two selected points (the centers of the two circles),
as shown in Figure 43-4.
4-1130
The Partition toolset
2. The user modifies the assembly, and the position of the selected points that defined the partition
changes. When ABAQUS/CAE regenerates the assembly, the partition is still defined as the line
between the center of the two circles, as shown in Figure 43-5.
You can use the Feature Manipulation toolset to make limited modifications to some partitions:
· You can enter a parameter to partition an edge directly and to position a Bézier curve that
partitions a face. The parameter must be between zero and one and represents a fraction of the
length of an edge; the Feature Manipulation toolset allows you to edit the value you provided.
· You can sketch a partition on a face; the Feature Manipulation toolset allows you to edit the
sketch.
If you need to change a partition that you cannot modify with the Feature Manipulation toolset, you
must delete the partition and recreate it.
4-1131
The Partition toolset
· When prompted to select a point, ABAQUS/CAE highlights the points you can select. You can
select one of the following:
- A datum point
· When prompted to select an edge, you can select edges or datum axes.
· When prompted to select a face, you can select faces or datum planes.
· ``An overview of the methods for partitioning cells, '' Section 43.4.3
Use parameter
Enter a parameter value that represents a fraction of the edge length, as shown in Figure 43-6.
An arrow along the edge indicates the direction of increasing parameter value from the start
vertex (corresponding to an edge parameter value of zero) to the end vertex (corresponding to
a value of one). For detailed instructions, see ``Using the parameter method to partition
edges,'' Section 43.5.1.
4-1132
The Partition toolset
Pick point
Select a point along the edge directly, as shown in Figure 43-7. For detailed instructions, see
``Using the pick method to partition an edge,'' Section 43.5.2.
Sketch
Partition a selected face by sketching a partition with the Sketcher, as shown in Figure 43-8.
For detailed instructions, see ``Using the sketch method to partition faces,'' Section 43.6.1.
You can sketch directly on the face to be partitioned, or you can sketch on a second face or
datum plane and then project the sketch onto the face that you want to partition. For an
example of projecting a sketch from a datum plane, see ``Using the Datum toolset in the Part
module,'' Section 14.11.1.
4-1133
The Partition toolset
Figure 43-9 Partitioning a face using the shortest path between two points.
4-1134
The Partition toolset
4-1135
The Partition toolset
Auto-partition
When you mesh a face with quadrilateral elements using the free meshing technique, the Mesh
module internally partitions the face into regions with three to five logical sides before
meshing the face. For more information, see ``Free meshing with quadrilateral elements,''
Section 20.9.2. However, if you want to view and perhaps modify the automatically generated
regions before generating the mesh, you can use the auto-partitioning tool to partition the face
without meshing it. This tool is available only in the Mesh module. For detailed instructions,
see ``Using the automatic generation method to partition faces, '' Section 43.6.7.
· Select a point on the cutting plane; then pick an edge or datum axis that defines the normal
to this plane, as shown in Figure 43-14.
4-1136
The Partition toolset
Figure 43-14 Defining the cutting plane with a point and a normal.
· Select an edge and a point along the edge; the cutting plane will be normal to the edge at
the selected point, as shown in Figure 43-16.
Figure 43-16 Defining the cutting plane with an edge and a point.
For detailed instructions, see ``Using the cutting plane method to partition cells, '' Section
43.7.1.
4-1137
The Partition toolset
Extend face
Partition a cell by cutting it with a shell, where the shell is the extended geometry of a face, as
shown in Figure 43-18. The face being extended can be planar, cylindrical, conical, or
spherical. For detailed instructions, see ``Using the extended face method to partition cells, ''
Section 43.7.3.
Extrude/Sweep edges
Partition a cell by sweeping selected edges (that form the sweep profile) along a selected path
(known as the sweep path). You can select any number of edges to be swept, although all the
edges must be connected, must lie on the same plane, and must belong to the same part
instance.
Use either of the following two methods to define the sweep path:
· Create a straight partition through the cell by extending the sweep profile infinitely in a
direction parallel to a selected straight edge or datum axis that acts as a sweep path; the
partition is created where the swept edge(s) pass through the selected cell, as shown in
Figure 43-19. The sweep path must be straight and perpendicular to the set of edges being
swept.
4-1138
The Partition toolset
· Create a straight or curved partition through the cell by extending the sweep profile along
or parallel to a selected edge. The partition extends only as far as the selected edge, and
the partition is created where the swept edge(s) pass through the selected cell, as shown in
Figure 43-20. The sweep path must begin in the plane containing the edges to be swept,
and its tangent must be perpendicular to the same plane.
For detailed instructions, see ``Using the extrude/sweep method to partition cells, '' Section
43.7.4.
N-sided patch
Partition a cell by dividing it with a patch having three, four, or five edges; the patch must pass
completely through the cell. Use either of the following two methods to define the patch:
· Select three, four, or five points that define the corners of the patch. If two of the points
are connected by an existing edge, the resulting partition will follow the curve of the edge,
as shown in Figure 43-21. The points must belong to the same part as the cell being
partitioned.
4-1139
The Partition toolset
· Select three, four, or five edges, as shown in Figure 43-22; the edges can be curved or
straight, must be connected, and must belong to the same part as the cell to be partitioned.
For detailed instructions, see ``Using the N-sided patch method to partition a cell, '' Section
43.7.5.
4-1140
The Partition toolset
To modify a partition that was created by specifying edge parameters, use the Feature Manipulation
toolset to change the edge parameter.
Detailed instructions for partitioning edges using the parameter method:
Tip: You can also use the parameter method to partition edges using the tool, located
with the partition edge tools in the module toolbox. For a diagram of the partition tools in the
toolbox, see ``Using the Partition toolset,'' Section 43.2.
2. From the Type radio buttons at the top of the dialog box, choose Edge.
The Method list displays the methods that you can use to partition an edge.
3. From the list of methods, select Use Parameter and click Apply.
4-1141
The Partition toolset
4. Select the edges to partition. You can use a combination of drag select, [Shift]+Click, and
[Ctrl]+Click to select more than one edge to partition.
ABAQUS/CAE highlights the selected edges, and an arrow indicates the direction of increasing
parameter value. If the line selection is ambiguous, you can cycle through the candidate edges
using the buttons in the prompt area.
5. Enter the desired edge parameter as a value between zero and one.
You cannot directly modify a partition that was created by clicking along the edge; you must delete the
partition and create a new one. However, if you select a datum point to position the partition and
subsequently move the datum point, the partition will move along with the datum. If you want to
partition the edge at a position other than the midpoint or a datum point, you should use the parameter
method.
Detailed instructions for partitioning an edge using the pick method:
Tip: You can also use the pick method to partition an edge using the tool, located with
the partition edge tools in the module toolbox. For a diagram of the partition tools in the
toolbox, see ``Using the Partition toolset,'' Section 43.2.
4-1142
The Partition toolset
2. From the Type radio buttons at the top of the dialog box, choose Edge.
The Method list displays the methods that you can use to partition an edge.
3. From the list of methods, select Pick point and click Apply.
5. Click the midpoint of the edge or a datum point along the edge.
ABAQUS/CAE displays the partition.
· ``Using the shortest path method to partition faces, '' Section 43.6.2
· ``Using the datum plane method to partition faces, '' Section 43.6.3
· ``Using the curved path method to partition a face, '' Section 43.6.4
· ``Using the automatic generation method to partition faces, '' Section 43.6.7
4-1143
The Partition toolset
the Sketcher when you want to create a partition whose shape cannot be achieved with any of the other
partition tools. Sketching a partition offers other advantages:
· You can use the Feature Manipulation toolset to modify the sketch if you want to change the shape
or the position of the partition.
· You can dimension the sketch precisely, and you can use the Feature Manipulation toolset to
modify the dimensions.
If the faces to be partitioned are planar and lie in the same plane, you can sketch directly on that plane.
Your sketch can extend beyond the boundaries of the selected faces, but the partition will not extend
beyond the edge of the faces. The following figure illustrates a sketched partition on a planar face:
If any of the faces to be partitioned are non-planar, you must sketch on a second planar face, and
ABAQUS/CAE creates the partition by projecting the sketch onto the faces to be partitioned. You can
specify the direction of the projection and the distance of the projection, normal to the sketch plane.
The following figure illustrates a sketched partition on a non-planar face using the projection of a
sketch drawn on a datum plane:
4-1144
The Partition toolset
Tip: You can also use the sketch method to partition edges using the tool, located with
the partition face tools in the module toolbox. For a diagram of the partition tools in the
toolbox, see ``Using the Partition toolset,'' Section 43.2.
2. From the Type radio buttons at the top of the dialog box, choose Face.
The Method list displays the methods that you can use to partition a face.
4. Select the faces to partition.If the selection is ambiguous, you can cycle through the candidate
faces using the buttons in the prompt area.
If you selected planar faces that lie in the same plane, ABAQUS uses that plane as the sketch
plane.
5. If the faces you selected include a non-planar face or do not lie in the same plane, do the
following:
b. From the buttons in the prompt area, select a method to determine how far ABAQUS/CAE
projects the sketch normal to the sketch plane. The partition is created wherever the
projected sketch extends through the non-planar face. The three methods are illustrated in
the following figure:
· If you selected the Through All method, ABAQUS/CAE asks you to choose which
direction the sketch will be projected.
· If you selected the Enter Value method, ABAQUS/CAE asks you to choose the
distance and direction that will be used to project the sketch. The default distance that
ABAQUS/CAE provides generates a partition that extends completely through the
non-planar face (resulting in the same partition as selecting Through All). The Feature
Manipulation toolset allows you to modify the projection distance after you create the
4-1145
The Partition toolset
partition.
· If you selected the Select Point method, ABAQUS/CAE asks you to choose the point
to which the sketch will be projected; the point defines both the direction and the
projection distance.
6. Select an edge that will appear vertical and on the right of the Sketcher grid. The edge must not be
perpendicular to the sketch plane.
The Sketcher starts with the planar face or datum plane selected as the sketch plane and
highlighted on the Sketcher grid.
Tip: If the part or assembly does not have a suitable edge, you can create a datum axis that
will provide the desired orientation. You can then select the datum axis as the edge to appear
vertical and on the right of the Sketcher grid.
7. Use the Sketcher to sketch the partition. From the main menu bar, click Done to indicate you have
finished sketching the partition.
Detailed instructions for partitioning faces using the shortest path method:
4-1146
The Partition toolset
Tip: You can also use the shortest path method to partition faces using the tool,
located with the partition face tools in the module toolbox. For a diagram of the partition tools
in the toolbox, see ``Using the Partition toolset,'' Section 43.2.
2. From the Type radio buttons at the top of the dialog box, choose Face.
The Method list displays the methods that you can use to partition a face.
3. From the list of methods, select Shortest path between 2 points and click Apply.
4. Select the faces to partition. You can use a combination of drag select, [Shift]+Click, and
[Ctrl]+Click to select more than one face to partition.
ABAQUS/CAE highlights the selected faces. If a selection is ambiguous, you can cycle through
the candidate faces using the buttons in the prompt area.
5. Select the vertices, midpoints, arc-centers, or datum points defining the start and end of the path.
ABAQUS/CAE highlights the points.
4-1147
The Partition toolset
Detailed instructions for partitioning faces using the datum plane method:
Tip: You can also use the datum plane method to partition faces using the tool, located
with the partition face tools in the module toolbox. For a diagram of the partition tools in the
toolbox, see ``Using the Partition toolset,'' Section 43.2.
2. From the Type radio buttons at the top of the dialog box, choose Face.
The Method list displays the methods that you can use to partition a face.
3. From the list of methods, select Use datum plane and click Apply.
4. Select the faces to partition. You can use a combination of drag select, [Shift]+Click, and
[Ctrl]+Click to select more than one face to partition.
ABAQUS/CAE highlights the selected faces. If a selection is ambiguous, you can cycle through
the candidate faces using the buttons in the prompt area.
5. Select an existing datum plane. If a datum plane does not exist in the desired location, create the
datum using the Datum toolset.
ABAQUS/CAE highlights the selected datum plane.
4-1148
The Partition toolset
You first select the face to partition and then select one of two methods to define the position of the
partition along the two edges; ABAQUS/CAE draws a Bézier curve connecting the two points. You
can locate the partition along the selected edges by either:
· Entering a parameter value between zero and one, where zero represents the start vertex of the
edge and one the end vertex. This method allows you to precisely position the partition anywhere
along the edges. In addition, you can subsequently modify the partition using the Feature
Manipulation toolset to edit the two parameters that you entered to locate the partition.
· Clicking the midpoint or a datum point along the edge. If you use this method to position a curved
partition, you will not be able to modify the partition later.
Detailed instructions for partitioning a face using the curved path method:
Tip: You can also use the curved path method to partition a face using the tool,
located with the partition face tools in the module toolbox.For a diagram of the partition tools
in the toolbox, see ``Using the Partition toolset,'' Section 43.2.
2. From the Type radio buttons at the top of the dialog box, choose Face.
The Method list displays the methods that you can use to partition a face.
3. From the list of methods, select Curved path normal to 2 edges and click Apply.
4-1149
The Partition toolset
4. Select the faces to partition. You can use a combination of drag select, [Shift]+Click, and
[Ctrl]+Click to select more than one face to partition.
ABAQUS/CAE highlights the selected faces. If a selection is ambiguous, you can cycle through
the candidate faces using the buttons in the prompt area.
5. From the buttons in the prompt area, select one of the following method to locate the curve:
· Use Parameter
· Pick
· If you selected the Use Parameter method, enter a value between zero and one. An arrow on
the selected edge indicates the direction of increasing parameter value.
· If you selected the Pick method, click the midpoint or a datum point along the selected edge.
8. Select a second edge that bounds the face and repeat the previous step. The angle subtended by the
two selected edges must be less than 180 degrees.
4-1150
The Partition toolset
If the infinite plane cannot intersect any of the selected faces, ABAQUS/CAE displays an error
message. The extended face need not belong to the same part as the faces to be partitioned; for
example, in the Assembly module you can partition the face of one part instance by extending the face
of a second.
Detailed instructions for partitioning faces using the extended face method:
Tip: You can also use the extended face method to partition faces using the tool,
located with the partition face tools in the module toolbox. For a diagram of the partition tools
in the toolbox, see ``Using the Partition toolset,'' Section 43.2.
2. From the Type radio buttons at the top of the dialog box, choose Face.
The Method list displays the methods that you can use to partition a face.
3. From the list of methods, select Extend another face and click Apply.
4. Select the faces to partition. You can use a combination of drag select, [Shift]+Click, and
[Ctrl]+Click to select more than one face to partition.
ABAQUS/CAE highlights the selected faces. If a selection is ambiguous, you can cycle through
the candidate faces using the buttons in the prompt area.
4-1151
The Partition toolset
The faces need not belong to the same part; for example, in the Assembly module you can partition the
face belonging to one part instance using its intersection with a face belonging to a second part
instance. The resulting regions are especially useful for defining contact or constraint interactions
between part instances.
The following figure shows two partitions that you might create at the intersection of three part
instances:
Tip: You can also use the intersection method to partition faces using the tool, located
with the partition face tools in the module toolbox. For a diagram of the partition tools in the
toolbox, see ``Using the Partition toolset,'' Section 43.2.
2. From the Type radio buttons at the top of the dialog box, choose Face.
The Method list displays the methods that you can use to partition a face.
4-1152
The Partition toolset
3. From the list of methods, select Intersect by other faces and click Apply.
4. Select the faces to partition. You can use a combination of drag select, [Shift]+Click, and
[Ctrl]+Click to select more than one face to partition.
ABAQUS/CAE highlights the selected faces. If a selection is ambiguous, you can cycle through
the candidate faces using the buttons in the prompt area.
Then, a mesh is generated on each of these regions, as shown in the following figure:
4-1153
The Partition toolset
Normally, when you mesh a face, these two steps take place in what appears to be a single step.
However, to gain more control over the meshing process, you can perform the partitioning step
separately using the automatic partitioning tool in the Partition toolset.
Since the automatic partitioning tool is associated with meshing, it is available only within the Mesh
module. After you automatically partition the face, you can gain additional control over the mesh by
seeding or by adding or deleting partitions manually.
Detailed instructions for partitioning faces using the automatic generation method:
Tip: You can also use the automatic generation method to partition faces using the
tool, located with the partition face tools in the module toolbox. For a diagram of the partition
tools in the toolbox, see ``Using the Partition toolset,'' Section 43.2.
2. From the Type radio buttons at the top of the dialog box, choose Face.
The Method list displays the methods that you can use to partition a face.
4. Select the faces to partition. You can use a combination of drag select, [Shift]+Click, and
[Ctrl]+Click to select more than one face to partition.
ABAQUS/CAE highlights the selected faces. If a selection is ambiguous, you can cycle through
the candidate faces using the buttons in the prompt area.
4-1154
The Partition toolset
· ``Using the cutting plane method to partition cells, '' Section 43.7.1
· ``Using the datum plane method to partition cells, '' Section 43.7.2
· ``Using the extended face method to partition cells, '' Section 43.7.3
· ``Using the N-sided patch method to partition a cell, '' Section 43.7.5
· Select a point and any straight edge. The cutting plane will pass through the point, normal to the
edge.
· Select three points. The cutting plane will pass through all three points.
· Select a straight or curved edge and a point on the edge. The cutting plane will pass through the
point, normal to the edge at the selected point.
Tip: You can also use the plane method to partition cells using the tool, located with
the partition cell tools in the module toolbox. For a diagram of the partition tools in the
toolbox, see ``Using the Partition toolset,'' Section 43.2.
2. From the Type radio buttons at the top of the dialog box, choose Cell.
4-1155
The Partition toolset
The Method list displays the methods that you can use to partition a cell.
3. From the list of methods, select Define cutting plane and click Apply.
4. Select the cell to partition. You can use a combination of drag select, [Shift]+Click, and
[Ctrl]+Click to select more than one cell to partition.
ABAQUS/CAE highlights the selected cell. If the selection is ambiguous, you can cycle through
the candidate cells using the buttons in the prompt area.
5. From the prompt area, click one of the following methods to define the cutting plane:
· Use the Point & normal method to partition the selected cells along a plane that passes
through a selected point and is normal to a selected straight edge or datum axis, as shown in
the following figure:
· Use the 3 Points method to partition the selectes cells along a plane passing through three
selected points, as shown in the following figure:
The three points can be anywhere on the part or assembly, but they must be distinct and they
must not be colinear.
· Use the Normal to edge method to partition the selected cells along a plane that is normal to a
selected edge and passes through a selected point on the edge. The edge can be straight or
curved, and need not be part of the cells being partitioned, although you cannot select a datum
axis. This method is useful when you want to partition a cell normal to a curved edge, as
shown in the following figure:
4-1156
The Partition toolset
6. Select points and edges as directed by the prompts in the prompt area. Points can be vertices,
midpoints, arc centers, or datum points.
· ``An overview of the methods for partitioning cells, '' Section 43.4.3
Detailed instructions for partitioning cells using the datum plane method:
Tip: You can also use the datum plane method to partition cells using the tool, located
with the partition cell tools in the module toolbox. For a diagram of the partition tools in the
toolbox, see ``Using the Partition toolset,'' Section 43.2.
2. From the Type radio buttons at the top of the dialog box, choose Cell.
The Method list displays the methods that you can use to partition a cell.
3. From the list of methods, select Use datum plane and click Apply.
4. Select the cell to partition. You can use a combination of drag select, [Shift]+Click, and
[Ctrl]+Click to select more than one cell to partition.
4-1157
The Partition toolset
ABAQUS/CAE highlights the selected cell. If the selection is ambiguous, you can cycle through
the candidate cells using the buttons in the prompt area.
5. Select an existing datum plane. If a datum plane does not exist in the desired location, create the
datum using the Datum toolset.
ABAQUS/CAE highlights the selected datum plane.
· ``An overview of the methods for partitioning cells, '' Section 43.4.3
If the infinite plane cannot intersect the cells, ABAQUS/CAE displays an error message. The extended
face need not belong to the same part as the cells to be partitioned; for example, in the Assembly
module you can partition the cell of one part instance by extending the face of a second.
Detailed instructions for partitioning cells using the extended geometry method:
Tip: You can also use the datum plane method to partition cells using the tool, located
with the partition cell tools in the module toolbox. For a diagram of the partition tools in the
toolbox, see ``Using the Partition toolset,'' Section 43.2.
4-1158
The Partition toolset
2. From the Type radio buttons at the top of the dialog box, choose Cell.
The Method list displays the methods that you can use to partition a cell.
3. From the list of methods, select Extend face and click Apply.
4. Select the cell to partition. You can use a combination of drag select, [Shift]+Click, and
[Ctrl]+Click to select more than one cell to partition.
ABAQUS/CAE highlights the selected cell. If the selection is ambiguous, you can cycle through
the candidate cells using the buttons in the prompt area.
5. Select the face that will be extended to create the desired partition.
ABAQUS/CAE highlights the selected faces. If any of the selections are ambiguous, you can cycle
through the candidate faces using the buttons in the prompt area.
· ``An overview of the methods for partitioning cells, '' Section 43.4.3
4-1159
The Partition toolset
Tip: You can also use the extrude/sweep method to partition cells using the tool,
located with the partition cell tools in the module toolbox. For a diagram of the partition tools
in the toolbox, see ``Using the Partition toolset,'' Section 43.2.
2. From the Type radio buttons at the top of the dialog box, choose Cell.
The Method list displays the methods that you can use to partition a cell.
3. From the list of methods, select Extrude/sweep edges and click Apply.
4. Select the cell to partition. You can use a combination of drag select, [Shift]+Click, and
[Ctrl]+Click to select more than one cell to partition.
ABAQUS/CAE highlights the selected cell. If the selection is ambiguous, you can cycle through
the candidate cells using the buttons in the prompt area.
5. To create the sweep profile, select the edges to sweep through the cells. The edges must all belong
to the same part, lie on the same plane, and be connected to each other.
ABAQUS/CAE highlights the selected edges.
6. From the buttons in the prompt area, click on one of the following methods to define the sweep
path:
· Use the Extrude along direction method to partition a cell by extruding selected edges--the
sweep profile--along a straight edge or datum axis--the sweep path--in a selected direction.
The sweep path must be perpendicular to the plane containing the sweep profile. The partition
extends infinitely in the selected direction through the selected cell. Extruding a sweep profile
along a direction to partition a cell is illustrated in the following figure:
· Use the Sweep along edge method to partition a cell by sweeping selected edges--the sweep
profile--along a straight or curved edge--the sweep path. The sweep path must begin in the
plane containing the sweep profile, and its tangent must be perpendicular to that same plane.
The resulting partition will extend only as far as the sweep path. Sweeping a sweep profile
along an edge to partition a cell is illustrated in the following figure:
4-1160
The Partition toolset
· ``An overview of the methods for partitioning cells, '' Section 43.4.3
Detailed instructions for partitioning a cell using the N-sided patch method:
Tip: You can also use the N-sided patch method to partition a cell using the tool,
4-1161
The Partition toolset
located with the partition cell tools in the module toolbox. For a diagram of the partition tools
in the toolbox, see ``Using the Partition toolset,'' Section 43.2.
2. From the Type radio buttons at the top of the dialog box, choose Cell.
The Method list displays the methods that you can use to partition a cell.
3. From the list of methods, select N-sided patch and click Apply.
4. Select the cell to partition. You can use a combination of drag select, [Shift]+Click, and
[Ctrl]+Click to select more than one cell to partition.
ABAQUS/CAE highlights the selected cell. If the selection is ambiguous, you can cycle through
the candidate cells using the buttons in the prompt area.
5. From the buttons in the prompt area, select one of the following methods to define the N-sided
patch:
· Use the Select Corner Points method to partition a cell by defining a N-sided patch using
three to five selected points. ABAQUS/CAE creates the patch by connecting the points in the
order that you select them; consequently, the order in which you select the points is
significant. The points can be vertices, mid-points, or datum points. If a curved edge connects
two of the points, the patch follows the contour of the curve, as shown in the following
figure:
· Use the Select Edges method to partition a cell by defining an N-sided patch using three to
five selected edges. The edges must belong to the same part as the cell being partitioned and
must form a closed loop, as shown in the following figure:
4-1162
The Partition toolset
· ``An overview of the methods for partitioning cells, '' Section 43.4.3
4-1163
The Query toolset
· Feature information:
- ID
- Parameters
- Parent-child information
In addition, if the current viewport contains the meshed assembly or an orphan mesh part imported
from an output database, the Query toolset provides the following information about a selected part or
part instance:
· Number of nodes
· Number of elements
Similarly, if the current viewport contains the meshed assembly or an orphan mesh part, the Query
toolset provides the following information about a selected element:
· Element label
5-1164
The Query toolset
· Nodal connectivity.
When you are using the Visualization module, items under General Queries in the Query toolset
provide the following general information:
For more information, see ``Obtaining general information about the model,'' Section 44.2.2.
In addition, the Query toolset can provide the following information specific to the module you are
using:
Part module
The items under Part Queries provide the following module-specific information about the
current part:
- Name
- Modeling space
For more information, see ``Using the Query toolset in the Part module,'' Section 14.11.4.
Property module
The items under Property Queries provide the following module-specific information about
the current part:
· Beam orientations assigned to a selected wire region (ABAQUS/CAE displays the (n1 ,
n2 , t) axis system on the selected wire region)
5-1165
The Query toolset
For more information, see ``Displaying information about section assignment and orientations
for a particular region,'' Section 15.11.4.
Assembly module
The items under Assembly Queries provide the following module-specific information about
a selected part instance:
For more information, see ``Using the Query toolset to query the assembly,'' Section 16.9.
Step module
The Query toolset provides only general information in the Step module.
Interaction module
The Query toolset provides only general information in the Interaction module.
Load/BC/IC module
The Query toolset provides only general information in the Load/BC/IC module.
Mesh module
The Region mesh item under Mesh Queries provides the following module-specific
information about a selected region:
· ID
· Element type
· Mesh algorithm and any options that were used to mesh the region
· Mesh pattern
5-1166
The Query toolset
The items under Mesh Queries display information only about meshes generated on native
part instances in the assembly. Select Instance mesh or Element from the list of General
Queries to obtain information about the mesh on an orphan mesh part imported from an
output database. For more information, see ``Obtaining mesh information and statistics,''
Section 20.17.
Job module
None of the ABAQUS/CAE toolsets are available in the Job module.
Sketch module
None of the ABAQUS/CAE toolsets are available in the Sketch module.
Visualization module
The items under Visualization Queries provide the following module-specific information:
· Probe values. ABAQUS/CAE displays information in the Probe Values dialog box as
you move the cursor around the current viewport. Probing a model plot displays model
data and analysis results; probing an X-Y plot displays X-Y curve data.
· Stress linearization. Stress linearization is the separation of stresses through a section into
constant membrane and linear bending stresses. ABAQUS/CAE performs stress
linearization calculations and displays the results in the form of an X-Y plot.
For more information, see Chapter 31, "Querying and probing" and Chapter 33, "Calculating
linearized stresses."
5-1167
The Query toolset
Tip: You can also query the model by clicking the query tool in the toolbar.
· General Queries
- Point
- Distance
- Feature
- Instance mesh
- Element
For more information, see ``Obtaining general information about the model,'' Section 44.2.2.
· Module-specific queries. For a complete list of the information available in each module, see
``Understanding the role of the Query toolset,'' Section 44.1.
3. From the bottom of the Query dialog box, click Apply. ABAQUS/CAE displays prompts in the
prompt area to guide you through the rest of the procedure.
ABAQUS/CAE displays the requested information in the message area. To resize the message
area, drag the small square at its upper right corner; to see information that has scrolled out of the
message area, use the scroll bar on the right side. The same information that appears in the
message area is also written to the replay file.
click the query tool in the toolbar. Select one of the following from the General Queries field in
the Query dialog box that appears:
5-1168
The Query toolset
Point
Select a point or node. ABAQUS/CAE displays the X-, Y-, and Z-coordinates of the point.
Distance
Select two points or nodes. ABAQUS/CAE displays the following:
· The X-, Y-, and Z-components of the vector between the two points.
Feature
Select a feature from the model, or click Feature List on the right side of the prompt area and
select a feature from the dialog box that appears. ABAQUS/CAE displays the following
information about the selected feature:
· Status--active or suppressed.
Alternatively, you can request information about all the features in the model. ABAQUS/CAE
displays a table containing each feature's ID, name, and status--active or suppressed.
Instance mesh
· Number of nodes
· Number of elements
Element
· Element label
5-1169
The Query toolset
· Nodal connectivity.
· Element quality
5-1170
The Set and Surface toolsets
· ``Understanding the role of the Set and Surface toolsets, '' Section 45.1
For detailed instructions on creating and manipulating sets and surfaces, see the following sections:
· ``Creating, editing, renaming, and deleting sets and surfaces,'' Section 45.3.1
· ``Associating objects (such as loads and sections) with sets and surfaces, '' Section 45.3.5
6-1171
The Set and Surface toolsets
· Create contact pairs with contact node sets and surfaces in the Interaction module.
· Request output from specific regions of the model in the Step module.
Geometry sets
A geometry set contains geometric objects (cells, faces, edges, and vertices) that you have
selected from one of the following types of parts or from instances of these parts:
· Native parts (those created using the tools in the Part module)
ABAQUS/CAE generates discrete sets (node sets and element sets) for each geometry set that
you have created and meshed. ABAQUS/CAE writes these discrete sets to the solver input file
using the *NSET and *ELSET options.
The most basic method for creating a geometry set is to select geometric objects directly from
the viewport. Depending on the shape and modeling space of the part, you can include any
combination of cells, faces, edges, and vertices in a geometry set. However, some operations
can be performed only on certain types of objects. In these cases the set that you use in the
operation must include only object types that are valid for the operation. For example,
concentrated forces can be applied only to vertices; therefore, the sets to which you apply
concentrated forces can include only vertices.
Discrete sets
6-1172
The Set and Surface toolsets
A discrete set contains either nodes or elements that you have selected from a part that was
imported from an output database or solver input file; that is, an orphan mesh part or part
instance. Discrete sets can include either elements or nodes, but not both. ABAQUS/CAE
writes these discrete sets to the solver input file using the *NSET and *ELSET options.
Although you can create discrete sets from orphan meshes, you cannot create them from native
meshes. (Native meshes are meshes that you create using the Mesh module.) If you are
working with native meshes, you must define geometry sets containing the geometry of the
underlying part or assembly; these sets are then converted to discrete sets when the solver
input file is generated.
If you create a discrete set and a geometry set from an assembly and give both sets the same name, the
name of the geometry set changes slightly when you create the solver input file. (The set name remains
unchanged in the model database.) In the input file, _G is appended to the name that you specify for
the geometry set to differentiate it from the discrete set. For example, if you name the sets Hinge, the
geometry set appears as Hinge_G in the input file. When you use sets in the Visualization module, the
sets are referred to by the names that appear in the input file. For example, to create a display group
containing only the geometry set that you named Hinge, you would select Hinge_G in the Create
Display Group dialog box. (For more information, see Chapter 36, "Displaying a subset of your
model.")
If you rename or delete a set, any objects associated with the set, such as sections or loads, become
invalid. However, if you change the name of a renamed set back to its original name or if you recreate
a deleted set using its original name, objects associated with that set are restored.
Part sets
Part sets are sets created in the Part or Property module. In the Property module you can assign
sections to regions specified by these sets. Part sets are not transferred to the assembly when
you instance the part; you must recreate the set in the Assembly, Step, Interaction, or
Load/BC/IC module if you need to use the set in any of these modules. However, the section
you assign to a region defined by a part set is copied automatically to all instances of that part
in the assembly. When you import an orphan mesh from an output database, you also
automatically import any sets stored with the mesh as part sets.
Assembly sets
Assembly sets contain regions of an assembly. You can use them to indicate, for example,
6-1173
The Set and Surface toolsets
regions of the assembly where you would like to apply a load or boundary condition or to
obtain output. Assembly sets can include regions from multiple part instances.
An assembly set refers to the assembly itself and not the individual part instances. As a result,
ABAQUS/CAE does not delete an assembly set if you delete a part instance contained in the
set. You must manually delete the assembly set.
When you use the input file reader to import an orphan mesh, ABAQUS/CAE reads the sets defined in
the input file and generates both a part set and an assembly set for each set encountered. However, if a
set is defined in the input file that spans both a deformable and a rigid part, ABAQUS/CAE generates
an assembly set and two part sets--one containing the nodes or elements from the deformable part and
one containing the nodes or elements from the rigid part. (For more information, see ``Importing
models from ABAQUS/Standard and ABAQUS/Explicit input files,'' Section 13.4.)
Geometry surfaces
Create a geometry surface by selecting geometric objects (faces and edges) from native or
imported geometry in an assembly. When the solver input file is created, the surface definition
in the input file specifies the element edges (in the case of axisymmetric part instances) or
faces that are associated with the surface geometry.
Mesh surfaces
Create a mesh surface by selecting element faces (for three-dimensional regions) or edges (for
two-dimensional regions) from orphan meshes in an assembly. Unlike sets, surface definitions
cannot be imported with orphan meshes.
If you rename or delete a surface, any objects associated with the surface, such as loads or interactions,
6-1174
The Set and Surface toolsets
become invalid. However, if you change the name of a renamed surface back to its original name or if
you recreate a deleted surface using its original name, objects associated with that surface are restored.
· If components of the feature were the only objects in a set or surface, the set or surface still
appears in the Set Manager but is empty. You can edit the set so that it includes new geometry.
· If components of the feature were included with other objects in a set or surface, the set or surface
no longer contains the components of the feature but continues to contain all of the other objects.
· If you suppress and then resume a feature, the sets and surfaces associated with that feature are
also restored, as well as any objects assigned to those sets and surfaces, such as loads or
interactions.
6-1175
The Set and Surface toolsets
In this case you can select the end with the magenta arrowhead, the end with the yellow arrowhead, or
the circumferential surface of the part instance, which is indicated by the red highlighted edge. If the
wire part instance is two-dimensional, you can select either the top or the bottom surface of the part.
Likewise, if the part is an axisymmetric shell, you can select either the inside or the outside surface of
the part.
6-1176
The Set and Surface toolsets
If you select more than one region for which you must specify a side, arrowheads appear in the
viewport for each region. For example, the face below is partitioned into two regions, and both regions
are selected; therefore, two sets of arrowheads appear.
In this example if you click Magenta in the prompt area, the near sides of both regions are selected. If
you click Yellow in the prompt area, the far sides of both regions are selected.
The third option in the prompt area, Flip a surface, allows you to switch the position of the colored
arrows for one or more of the selected regions. For example, in the figure below the arrowheads for the
region on the right were flipped; and the magenta arrowhead now points to the far side of that region.
If you clicked Magenta in the prompt area, the far side of the region on the right and the near side of
the region on the left would both be selected.
6-1177
The Set and Surface toolsets
· ``Creating, editing, renaming, and deleting sets and surfaces,'' Section 45.3.1
· ``Associating objects (such as loads and sections) with sets and surfaces, '' Section 45.3.5
· The Create, Edit, Rename, and Delete items listed under the Tools->Set and Tools->Surface
submenus in the main menu bar.
The Edit, Rename, and Delete menu items contain submenus listing all of the sets or surfaces in
the current model. The Set submenus vary depending on which module you are in; in the Part and
Property modules, only part sets are listed, while in all other modules, only assembly sets are
listed.
6-1178
The Set and Surface toolsets
· The set and surface managers. These managers contain functions identical to those listed under the
Set and Surface submenus but with convenient browsers that list all of the sets or surfaces within
the current model along with their type (such as geometry or mesh).
Note: Sets and surfaces that are empty as a result of feature modification will still appear in
the lists. See ``Regeneration of geometry sets and surfaces,'' Section 45.2.4, for more
information.
Warning: When you delete a set or surface, any objects associated with that set or surface, such
as loads or interactions, become invalid.
The Create Set dialog box appears. The dialog box lists the types of sets you can create.
a. Enter a name for the set. For information on naming objects, see ``Using basic dialog box
components,'' Section 6.3.1.
Each set name must be unique within the category to which it belongs; for example,
different geometry sets must have different names. However, a geometry set, an element
set, and a node set can all have the same name, and a set can have the same name as a
surface. In addition, part sets from different parts can have identical names.
c. Click Continue.
6-1179
The Set and Surface toolsets
3. Select the objects in the viewport that you want to include in your set.
Tip: You can limit the types of objects that you can select in the viewport by clicking the
selection options tool in the prompt area and then clicking the options of your choice in
the dialog box that appears. For more information, see Chapter 9, "Selecting objects within the
viewport."
When you are finished selecting objects, click mouse button 2.
The Create Surface dialog box appears. The dialog box lists the types of surfaces you can create.
a. Enter a name for the surface. For information on naming objects, see ``Using basic dialog
box components,'' Section 6.3.1.
All surfaces in an assembly must have unique names regardless of whether they consist of
mesh or geometric objects.
b. Click Continue.
3. Select the objects in the viewport that you want to include in your set.
Tip: You can limit the types of objects that you can select in the viewport by clicking the
selection options tool in the prompt area and then clicking the options of your choice in
the dialog box that appears. For more information, see Chapter 9, "Selecting objects within the
viewport."
When you are finished selecting objects, click mouse button 2.
6-1180
The Set and Surface toolsets
If you must specify which side of the surface you want to select, a pair of different colored arrows
appears; one arrow points to one side of the surface and the other arrow points to the other side of
the surface.
If you must specify which surface on a beam you want to select, different colored arrows appear at
each end of the beam and, in three-dimensional space, the beam itself becomes highlighted. (For
more information, see ``Specifying a particular side or end of a region,'' Section 45.2.5.)
4. If you must specify a side of a surface, click the button in the prompt area that is labeled with the
color of the arrow pointing to the side of interest.
5. If you must specify the surface of a beam, click one of the following in the prompt area:
· Click the button in the prompt area that is labeled with the arrow color appearing at the end
surface of interest.
· If applicable, click Circumferential to select the outer surface of the beam, excluding the end
surfaces.
For more information on selecting beam surfaces and indicating sidedness, see ``Understanding the
correspondence between geometric and physical objects,'' Section 9.1.2, and ``Specifying a particular
side or end of a region,'' Section 45.2.5.
Note: You can also click Edit in the Set Manager or in the Surface Manager after selecting
the name of the set or surface of interest.
2. In the viewport, reselect objects to include in the set or surface. Use [Shift]+Click and
[Ctrl]+Click to change which objects are selected in the viewport.
Tip: You can limit the types of objects that you can select in the viewport by clicking the
6-1181
The Set and Surface toolsets
selection options tool in the prompt area and then clicking the options of your choice in
the dialog box that appears. For more information, see Chapter 9, "Selecting objects within the
viewport."
When you are finished selecting objects, click mouse button 2.
3. If necessary, specify the side or end of the regions that you want to include in the surface and then
click mouse button 2. (For more information, see ``Specifying a particular side or end of a region,''
Section 45.2.5.)
1. In the prompt area, click the button labeled either Sets or Surfaces. (The label of the button
varies depending on the type of object you are defining; for example, if you are defining a pressure
load, the button is labeled Surfaces).
The Region Selection dialog box appears.
ABAQUS/CAE displays prompts in the prompt area to guide you through the procedure.
2. In the Region Selection dialog box, select the region of your choice.
4. Click Continue to close the dialog box and continue to the next step of the procedure.
6-1182
The Set and Surface toolsets
6-1183
Customizing geometry and mesh display
0-1184
Selecting geometry and mesh display options
· ``Controlling the display of loads, boundary conditions, and initial conditions, '' Section 46.8
In geometry-related modules you can use this menu item to control your geometry render style,
edge visibility, curve refinement, element and node labels, and the visibility of the various
types of datum geometry.
View->Assembly Display Options
In assembly-related modules you can use this menu item to control your assembly render style,
edge visibility, and the visibility of the various types of datum geometry. You can also use it to
control the display of the mesh, element and node labels, part instances, loads, boundary
conditions, and initial conditions in those same assembly-related modules.
View->ODB Display Options
This menu item is applicable only to the Visualization module. For more information, see
Chapter 37, "Customizing model display."
1-1185
Selecting geometry and mesh display options
Render style is the style in which ABAQUS displays your model. You can use the View->Part Display
Options and View->Assembly Display Options menu items to display your model in one of three
render styles: wireframe, hidden, or shaded; these styles are shown in Figure 46-1. An explanation of
these choices follows.
Figure 46-1 Model showing render style options. From left to right: the wireframe, hidden, and
lightsource-shaded render styles.
Wireframe
Displays model edges; both interior and exterior edges are potentially visible. Wireframe plots
produce a frame-like visual effect in which model faces are not displayed. Wireframe is the
most rapidly drawn render style.
Hidden
Displays a wireframe plot in which edges obscured by the model are either not shown or are
shown as dotted lines, depending on which option you select. (For more information on this
option, see ``Controlling edge visibility,'' Section 46.3.) Hidden plots produce a solid rather
than frame-like appearance.
Shaded
Displays a filled plot in which a light source appears to be directed at the model. Shaded plots
produce a highly three-dimensional visual effect.
2. Click Wireframe, Hidden, or Shaded to select the style that you want.
Tip: You can also select the render style using the Wireframe , Hidden , and
1-1186
Selecting geometry and mesh display options
Geometry edges
· If a part or part instance is displayed with the hidden render style, ABAQUS/CAE suppresses
obscured geometry edges by default. Alternatively, if you toggle on the Show dotted lines in
hidden render style option, ABAQUS/CAE displays the obscured edges using a dotted line
style.
If a part or part instance is displayed with the shaded render style, ABAQUS/CAE displays the
edges by default. Alternatively, if you toggle off the Show edges in shaded render style
option, ABAQUS/CAE suppresses edge display.
If a three-dimensional part or part instance contains faces with curved edges, by default
ABAQUS/CAE displays gray ``silhouette'' edges originating from the faces, as shown in the
hidden-line plot in Figure 46-2. Unlike true edges, silhouette edges serve only as a visual aid;
for example, you cannot select or partition a silhouette edge.
Alternatively, if you toggle off the Show silhouette edges option, ABAQUS/CAE displays
1-1187
Selecting geometry and mesh display options
Mesh edges
For mesh edges within a meshed part or a part imported from an output database, the visibility
options are:
All
Displays all element edges. To see element edges on the interior of the model, you
must also set the render style to wireframe.
Exterior
Displays only edges on the exterior of the model.
Feature
Displays only edges on the exterior of the model that are calculated to be feature
edges. Feature edges lie between elements that have normals that differ by more than
the ``feature angle.'' For more information on controlling the feature angle, see
``Defining mesh feature edges,'' Section 46.5.
Free
Displays only edges that belong to a single element. Free edge display is particularly
useful for locating potential holes or cracks in your mesh.
If a mesh is displayed with the shaded render style, ABAQUS/CAE displays the edges by
default. Alternatively, if you toggle off the Show edges in shaded render style option,
ABAQUS/CAE suppresses edge display.
With the exception of showing hidden geometry edges as dotted lines, you cannot control the line
style, color, or thickness of edges.
Detailed instructions for controlling edge visibility:
1-1188
Selecting geometry and mesh display options
1-1189
Selecting geometry and mesh display options
ABAQUS/CAE applies the curve refinement setting only to the part in the current viewport.
Figure 46-4 Plots showing feature angles of 0°, 5°, and 20°.
Feature edges are defined as adjacent edges with normals that differ by more than the " feature angle."
You can customize the feature angle when you select Feature mesh edge visibility. Larger angles will
reduce the number of feature edges; conversely, smaller angles will cause more edges to be visible.
The default mesh feature angle is 20°.
2. From the bottom of the dialog box, select Feature from the list of mesh edges to show.
ABAQUS/CAE displays an Angle data field to the right of Feature.
3. Click the Angle data entry field, and enter the desired feature angle.
1-1190
Selecting geometry and mesh display options
· Datum points
· Datum axes
· Datum planes
1-1191
Selecting geometry and mesh display options
2. Toggle Show native mesh to display or suppress the native mesh. When Show native mesh is
on, native mesh display options become available. Do one of the following:
· Choose Mesh module only to display your native mesh only in the Mesh module.
· Choose All assembly-related modules to display your native mesh in all modules that
support the display of the assembly.
3. Toggle Show node labels and Show element labels to affect the display of these items.
1-1192
Selecting geometry and mesh display options
From the main menu bar, select View->Assembly Display Options. The Assembly Display
Options dialog box appears. Click the Load, BC, or IC tab to control the display of loads,
boundary conditions, and initial conditions, respectively.
a. Click Load/BC/IC module only to display the object only in the Load/BC/IC module.
b. Click All assembly-related modules to display the object in all modules that support the
display of the assembly.
When Show object of your choice (in current step) is toggled off, ABAQUS/CAE does not
display that object in any module.
· Click Set All Off to turn off the display of all instances.
1-1193
Selecting geometry and mesh display options
1-1194
Appendix A: Keyword support
This appendix contains a table you can use to determine whether a particular ABAQUS keyword's
functionality is supported by ABAQUS/CAE, and if so, which ABAQUS/CAE module embodies that
functionality. The table is contained in the following section:
You can also view this section by selecting Help->Keyword Browser from the main menu bar.
This appendix also describes the support from the ABAQUS/CAE input file reader for ABAQUS
keywords. The description is contained in the following section:
The input file reader is described in ``Importing models from ABAQUS/Standard and
ABAQUS/Explicit input files,'' Section 13.4.
0-1195
*AXIAL Used to define the axial behavior Unsupported
of beams.
*BASE MOTION Define the base motion for linear, Unsupported
eigenmode-based, dynamic
procedures.
*BASELINE Include baseline correction. Amplitude toolset
CORRECTION
*BEAM GENERAL Specify a beam section when Property module
SECTION numerical integration over the
section is not required.
*BEAM SECTION Specify a beam section when Property module
numerical integration over the
section is required.
*BIAXIAL TEST Used to provide equibiaxial test Property module
DATA data (compression and/or
tension).
*BOND Define bonds and bonding Unsupported
properties.
*BOUNDARY Specify boundary conditions. Load/BC/IC
module
*BRITTLE Define brittle cracking Unsupported
CRACKING properties.
*BRITTLE FAILURE Specify brittle failure criterion. Unsupported
*BRITTLE SHEAR Define the postcracking shear Unsupported
behavior of a material used with
the brittle cracking model.
*BUCKLE Obtain eigenvalue buckling Step module
estimates.
*BUCKLING Define a nondefault buckling Unsupported
ENVELOPE envelope for buckling strut
response of frame elements with
PIPE sections.
*BUCKLING LENGTH Define buckling length data for Unsupported
buckling strut response of frame
elements with PIPE sections.
*BUCKLING Define buckling reduction factors Unsupported
REDUCTION for buckling strut response of
0-1196
FACTORS frame elements with PIPE
sections.
*BULK VISCOSITY Modify bulk viscosity Step module
parameters.
*C ADDED MASS Specify concentrated added mass Unsupported
in a *FREQUENCY step.
*CAP CREEP Specify a cap creep law and Property module
material properties.
*CAP HARDENING Specify Drucker-Prager/Cap Property module
plasticity hardening.
*CAP PLASTICITY Specify the Modified Property module
Drucker-Prager/Cap plasticity
model.
*CAST IRON Specify hardening in Unsupported
COMPRESSION compression for the gray cast
HARDENING iron plasticity model.
*CAST IRON Specify plastic material Unsupported
PLASTICITY properties for gray cast iron.
*CAST IRON Specify hardening in tension for Unsupported
TENSION the gray cast iron plasticity
HARDENING model.
*CAVITY Define a cavity for thermal Unsupported
DEFINITION radiation.
*CECHARGE Specify concentrated electric Unsupported
charges in piezoelectric analysis.
*CECURRENT Specify concentrated current in Unsupported
an electric conduction analysis.
*CENTROID Define the position of the Unsupported
centroid of the beam section.
*CFILM Define film coefficients and Unsupported
associated sink temperatures at a
node.
*CFLUX Specify concentrated fluxes in Load/BC/IC
heat transfer or mass diffusion module
analyses.
*CHANGE FRICTION Change friction properties. Interaction
module
0-1197
*CLAY HARDENING Specify hardening for the clay Property module
plasticity model.
*CLAY PLASTICITY Specify the extended Cam-clay Property module
plasticity model.
*CLEARANCE Specify a particular initial Unsupported
clearance value and a contact
direction for the slave nodes on a
surface.
*CLOAD Specify concentrated forces and Load/BC/IC
moments. module
*COMBINED TEST Specify simultaneously the Property module
DATA normalized shear and bulk
compliances or relaxation moduli
as functions of time.
*CONCRETE Define concrete properties Property module
beyond the elastic range.
*CONDUCTIVITY Specify thermal conductivity. Property module
*CONNECTOR Begin the specification of a Unsupported
BEHAVIOR connector behavior.
*CONNECTOR Define reference lengths and Unsupported
CONSTITUTIVE angles to be used in specifying
REFERENCE connector constitutive behavior.
*CONNECTOR Define connector damping Unsupported
DAMPING behavior.
*CONNECTOR Define connector elastic Unsupported
ELASTICITY behavior.
*CONNECTOR Define a failure criterion for Unsupported
FAILURE connector elements.
*CONNECTOR Define friction forces and Unsupported
FRICTION moments in connector elements.
*CONNECTOR LOAD Specify loads for available Load/BC/IC
components of relative motion in module
connector elements.
*CONNECTOR LOCK Define a locking criterion for Unsupported
connector elements.
*CONNECTOR Specify the motion of available Load/BC/IC
0-1198
MOTION components of relative motion in module
connector elements.
*CONNECTOR Specify connector attributes for Unsupported
SECTION connector elements.
*CONNECTOR STOP Specify connector stops for Unsupported
connector elements.
*CONTACT Specify additional controls for Step module
CONTROLS contact.
*CONTACT Define viscous damping between Interaction
DAMPING contacting surfaces. module
*CONTACT FILE Define results file requests for Not applicable
contact variables.
*CONTACT Prescribe time-dependent Interaction
INTERFERENCE allowable interferences of contact module
pairs and contact elements.
*CONTACT NODE Assign nodes to a contact node Interaction
SET set. module
*CONTACT OUTPUT Specify contact variables to be Step module
written to the output database.
*CONTACT PAIR Define surfaces that contact each Interaction
other. module
*CONTACT PRINT Define print requests for contact Step module
variables.
*CONTACT Define contact responses for Unsupported
RESPONSE design sensitivity analysis.
*CONTOUR Provide contour integral Unsupported
INTEGRAL estimates.
*CONTROLS Reset solution controls. Unsupported
*CORRELATION Define cross-correlation Unsupported
properties for random response
loading.
*COUPLED Fully coupled, simultaneous heat Step module
TEMPERATURE-DISP transfer and stress analysis.
LACEMENT
*COUPLED Fully coupled, simultaneous heat Step module
THERMAL-ELECTRIC transfer and electrical analysis.
0-1199
AL
*CRADIATE Specify radiation conditions. Unsupported
*CREEP Define a creep law. Property module
*CREEP STRAIN Control loadings based on the Unsupported
RATE CONTROL maximum equivalent creep strain
rate.
*CYCLED PLASTIC Specify cycled yield stress data Property module
for the *ORNL model.
*CYCLIC Define cyclic symmetry for a Unsupported
cavity radiation heat transfer
analysis.
*CYCLIC Specify the size of the elastic Unsupported
HARDENING range for the combined hardening
model.
*CYCLIC Define the number of sectors and Unsupported
SYMMETRY MODEL the axis of symmetry for a cyclic
symmetric structure.
*D ADDED MASS Specify distributed added mass in Unsupported
a *FREQUENCY step.
*DAMPING Specify material damping. Property module
*DASHPOT Define dashpot behavior. Unsupported
*DEBOND Activate crack propagation Unsupported
capability and specify debonding
amplitude curve.
*DECHARGE Input distributed electric charges Unsupported
for piezoelectric analysis.
*DECURRENT Specify distributed current Unsupported
densities in an electric
conduction analysis.
*DEFORMATION Specify the deformation plasticity Property module
PLASTICITY model.
*DENSITY Specify material mass density. Property module
*DEPVAR Specify solution-dependent state Property module
variables.
*DESIGN GRADIENT Directly specify design gradients Unsupported
for design sensitivity analysis.
0-1200
*DESIGN Specify design parameters with Unsupported
PARAMETER respect to which sensitivities are
calculated.
*DESIGN RESPONSE Specify responses for design Unsupported
sensitivity analysis.
*DETONATION Define detonation points for a Unsupported
POINT JWL explosive equation of state.
*DFLOW Specify distributed seepage flows Unsupported
for consolidation analysis.
*DFLUX Specify distributed fluxes in heat Unsupported
transfer or mass diffusion
analyses.
*DIAGNOSTICS Control diagnostic messages. Step module
*DIELECTRIC Specify dielectric material Property module
properties.
*DIFFUSIVITY Specify mass diffusivity. Property module
*DISTRIBUTING Specify nodes and weighting for Unsupported
COUPLING distributing coupling elements.
*DLOAD Specify distributed loads. Load/BC/IC
module
*DRAG CHAIN Specify parameters for drag chain Unsupported
elements.
*DRUCKER PRAGER Specify the extended Property module
Drucker-Prager plasticity model.
*DRUCKER PRAGER Specify a Drucker-Prager creep Property module
CREEP law and material properties.
*DRUCKER PRAGER Specify hardening for Property module
HARDENING Drucker-Prager plasticity models.
*DSA CONTROLS Set DSA solution controls. Unsupported
*DSECHARGE Input distributed electric surface Unsupported
charges for piezoelectric
analysis.
*DSECURRENT Specify distributed current Unsupported
densities over a surface in an
electric conduction analysis.
*DSFLOW Specify distributed seepage flows Unsupported
0-1201
normal to a surface.
*DSFLUX Specify distributed surface fluxes Load/BC/IC
for heat transfer analysis. module
*DSLOAD Specify distributed surface loads. Load/BC/IC
module
*DYNAMIC Dynamic stress/displacement Step module
analysis.
*DYNAMIC Dynamic coupled thermal-stress Step module
TEMPERATURE-DISP analysis using explicit
LACEMENT integration.
*EL FILE Define results file requests for Not applicable
element variables.
*EL PRINT Define data file requests for Not applicable
element variables.
*ELASTIC Specify elastic material Property module
properties.
*ELCOPY Create elements by copying from Not applicable
an existing element set.
*ELECTRICAL Specify electrical conductivity. Property module
CONDUCTIVITY
*ELEMENT Define elements by giving their Mesh module
nodes.
*ELEMENT MATRIX Write element stiffness matrices Unsupported
OUTPUT and mass matrices to a file.
*ELEMENT OUTPUT Define output database requests Step module
for element variables.
*ELEMENT Define element responses for Unsupported
RESPONSE design sensitivity analysis.
*ELGEN Incremental element generation. Not applicable
*ELSET Assign elements to an element Set toolset
set.
*EMISSIVITY Specify surface emissivity. Unsupported
*END ASSEMBLY End the definition of an Assembly module
assembly.
*END INSTANCE End the definition of an instance. Assembly module
0-1202
*END PART End the definition of a part. Part module
*END PRELOAD End the preloading definition of a Unsupported
superelement.
*END STEP End the definition of a step. Step module
*END SUPER End a superelement definition. Unsupported
*ENERGY FILE Write energy output to the results Not applicable
file.
*ENERGY OUTPUT Define output database requests Step module
for whole model or element set
energy data.
*ENERGY PRINT Print a summary of the total Not applicable
energies.
*EOS Specify an equation of state Unsupported
model.
*EOS SHEAR Specify shear behavior for an Unsupported
equation of state material.
*EPJOINT Define properties for Unsupported
elastic-plastic joint elements.
*EQUATION Define linear multi-point Interaction
constraints. module
*EXPANSION Specify thermal expansion. Property module
*EXTREME Define element variables to be Unsupported
ELEMENT VALUE monitored.
*EXTREME NODE Define nodal variables to be Unsupported
VALUE monitored.
*EXTREME VALUE Define element and nodal Unsupported
variables to be monitored.
*FAIL STRAIN Define parameters for Property module
strain-based failure measures.
*FAIL STRESS Define parameters for Property module
stress-based failure measures.
*FAILURE RATIOS Define the shape of the failure Property module
surface for a *CONCRETE
model.
*FIELD Specify predefined field variable Unsupported
0-1203
values.
*FILE FORMAT Specify format for results file Not applicable
output and invoke zero-increment
results file output.
*FILE OUTPUT Define output written to the Not applicable
results file.
*FILM Define film coefficients and Unsupported
associated sink temperatures.
*FILM PROPERTY Define a film coefficient as a Interaction
function of temperature and field module
variables.
*FIXED MASS Specify mass scaling at the Step module
SCALING beginning of the step.
*FLOW Define seepage coefficients and Unsupported
associated sink pore pressures.
*FLUID BULK Define compressibility for a Unsupported
MODULUS hydraulic fluid.
*FLUID DENSITY Specify hydrostatic fluid density. Unsupported
*FLUID EXPANSION Specify the thermal expansion Unsupported
coefficient for a hydraulic fluid.
*FLUID FLUX Change the amount of fluid in a Unsupported
fluid-filled cavity.
*FLUID LINK Define properties for fluid link Unsupported
elements.
*FLUID PROPERTY Define properties for hydrostatic Unsupported
fluid elements.
*FOAM Specify the crushable foam Property module
plasticity model.
*FOAM HARDENING Specify hardening for the Property module
crushable foam plasticity model.
*FOUNDATION Prescribe element foundations. Interaction
module
*FRACTURE Specify crack propagation Unsupported
CRITERION criteria.
*FRAME SECTION Specify a frame section. Unsupported
0-1204
*FREQUENCY Extract natural frequencies and Step module
modal vectors.
*FRICTION Specify a friction model. Interaction
module
*GAP Specify clearance and local Unsupported
geometry for GAP-type elements.
*GAP Introduce heat conductance Interaction
CONDUCTANCE between interface surfaces. module
*GAP ELECTRICAL Specify electrical conductance Unsupported
CONDUCTANCE between surfaces.
*GAP HEAT Introduce heat generation due to Interaction
GENERATION energy dissipation at the module
interface.
*GAP RADIATION Introduce heat radiation between Interaction
surfaces. module
*GASKET BEHAVIOR Begin the specification of a Property module
gasket behavior.
*GASKET CONTACT Specify a gasket contact area or Property module
AREA contact width for average
pressure output.
*GASKET Specify elastic properties for the Property module
ELASTICITY membrane and transverse shear
behaviors of a gasket.
*GASKET SECTION Specify element properties for Property module
gasket elements.
*GASKET Specify a gasket Property module
THICKNESS thickness-direction behavior.
BEHAVIOR
*GEL Define a swelling gel. Property module
*GEOSTATIC Obtain a geostatic stress field. Step module
*HEADING Print a heading on the output. Job module
*HEATCAP Specify a point capacitance. Property module
*HEAT GENERATION Include volumetric heat Property module
generation in heat transfer
analyses.
*HEAT TRANSFER Transient or steady-state Step module
0-1205
uncoupled heat transfer analysis.
*HOURGLASS Specify nondefault hourglass Unsupported
STIFFNESS stiffness.
*HYPERELASTIC Specify elastic properties for Property module
approximately incompressible
elastomers.
*HYPERFOAM Specify elastic properties for a Property module
hyperelastic foam.
*HYPOELASTIC Specify hypoelastic material Property module
properties.
*HYSTERESIS Specify a rate-dependent Unsupported
elastomer model.
*IMPEDANCE Define impedances for acoustic Unsupported
analysis.
*IMPEDANCE Define the impedance parameters Unsupported
PROPERTY for an acoustic medium
boundary.
*IMPERFECTION Introduce geometric Unsupported
imperfections for postbuckling
analysis.
*IMPORT Import information from a Unsupported
previous ABAQUS/Explicit or
ABAQUS/Standard analysis.
*IMPORT CONTROLS Specify tolerances used in Unsupported
importing model and results data.
*IMPORT ELSET Import element set definitions Unsupported
from a previous
ABAQUS/Explicit or
ABAQUS/Standard analysis.
*IMPORT NSET Import node set definitions from Unsupported
a previous ABAQUS/Explicit or
ABAQUS/Standard analysis.
*INCLUDE Reference an external file Not applicable
containing ABAQUS input data.
*INCREMENTATION Define output database requests Step module
OUTPUT for time incrementation data.
*INELASTIC HEAT Define the fraction of the rate of Property module
0-1206
FRACTION inelastic dissipation that appears
as a heat source.
*INITIAL Specify initial conditions for the Load/BC/IC
CONDITIONS model. module
*INSTANCE Begin an instance definition. Assembly module
*INTERFACE Define properties for contact Not applicable
elements.
*ITS Define properties for ITS Unsupported
elements.
*JOINT Define properties for JOINTC Unsupported
elements.
*JOINT ELASTICITY Specify elastic properties for Unsupported
elastic-plastic joint elements.
*JOINT PLASTICITY Specify plastic properties for Unsupported
elastic-plastic joint elements.
*JOINTED Specify the jointed material Unsupported
MATERIAL model.
*JOULE HEAT Define the fraction of electric Property module
FRACTION energy released as heat.
*KAPPA Specify the material parameters Property module
∙s and ∙p for mass diffusion
driven by gradients of
temperature and equivalent
pressure stress, respectively.
*KINEMATIC Constrain all or specific degrees Unsupported
COUPLING of freedom of a set of nodes to
the rigid body motion of a
reference node.
*LATENT HEAT Specify latent heats. Property module
*MAP SOLUTION Map a solution from an old mesh Unsupported
to a new mesh.
*MASS Specify a point mass. Property module
*MASS DIFFUSION Transient or steady-state Step module
uncoupled mass diffusion
analysis.
*MASS FLOW RATE Specify fluid mass flow rate in a Unsupported
0-1207
heat transfer analysis.
*MATERIAL Begin the definition of a Property module
material.
*MATRIX Read in the stiffness or mass Unsupported
matrix for a linear user element.
*MEMBRANE Specify section properties for Property module
SECTION membrane elements.
*MODAL DAMPING Specify damping for modal Step module
dynamic analysis.
*MODAL DYNAMIC Dynamic time history analysis Step module
using modal superposition.
*MODAL FILE Write generalized coordinate Not applicable
(modal amplitude) data to the
results file during a linear
dynamic procedure.
*MODAL OUTPUT Write generalized coordinate Step module
(modal amplitude) data to the
output database during a linear
dynamic procedure.
*MODAL PRINT Print generalized coordinate Not applicable
(modal amplitude) data during a
linear dynamic procedure.
*MODEL CHANGE Remove or reactivate elements Interaction
and contact pairs. module
*MOHR COULOMB Specify the Mohr-Coulomb Unsupported
plasticity model.
*MOHR COULOMB Specify hardening for the Unsupported
HARDENING Mohr-Coulomb plasticity model.
*MOISTURE Define moisture-driven swelling. Property module
SWELLING
*MONITOR Define a degree of freedom to Step module
monitor.
*MOTION Specify motions as a predefined Unsupported
field.
*MPC Define multi-point constraints. Unsupported
*M1 Used to define the first bending Unsupported
0-1208
moment behavior of beams.
*M2 Used to define the second Unsupported
bending moment behavior of
beams.
*NCOPY Create nodes by copying. Not applicable
*NFILL Fill in nodes in a region. Not applicable
*NGEN Generate incremental nodes. Not applicable
*NMAP Map nodes from one coordinate Not applicable
system to another.
*NO COMPRESSION Introduce a compressive failure Unsupported
theory (tension only materials).
*NO TENSION Introduce a tension failure theory Unsupported
(compression only material).
*NODAL THICKNESS Define shell or membrane Unsupported
thickness at nodes.
*NODE Specify nodal coordinates. Mesh module
*NODE FILE Define results file requests for Not applicable
nodal data.
*NODE OUTPUT Define output database requests Step module
for nodal data.
*NODE PRINT Define print requests for nodal Not applicable
variables.
*NODE RESPONSE Define nodal responses for Unsupported
design sensitivity analysis.
*NORMAL Specify a particular normal Unsupported
direction.
*NSET Assign nodes to a node set. Set toolset
*ORIENTATION Define a local axis system for Property module
material or element property
definition or for kinematic
coupling constraints.
*ORNL Specify constitutive model Property module
developed by Oak Ridge
National Laboratory.
*OUTPUT Define output requests to the Step module
0-1209
output database.
*PARAMETER Define parameters for input Unsupported
parametrization.
*PARAMETER Define dependence table for Unsupported
DEPENDENCE tabularly dependent parameters.
*PARAMETER Define parametric shape Unsupported
SHAPE VARIATION variations.
*PART Begin a part definition. Part module
*PERIODIC Define periodic symmetry for a Unsupported
cavity radiation heat transfer
analysis.
*PERMEABILITY Define permeability for pore fluid Property module
flow.
*PHYSICAL Specify physical constants. Unsupported
CONSTANTS
*PIEZOELECTRIC Specify piezoelectric material Property module
properties.
*PIPE-SOIL Specify element properties for Unsupported
INTERACTION pipe-soil interaction elements.
*PIPE-SOIL Define constitutive behavior for Unsupported
STIFFNESS pipe-soil interaction elements.
*PLANAR TEST Used to provide planar test (or Property module
DATA pure shear) data (compression
and/or tension).
*PLASTIC Specify a metal plasticity model. Property module
*PLASTIC AXIAL Define plastic axial force for Unsupported
frame elements.
*PLASTIC M1 Define the first plastic bending Unsupported
moment behavior for frame
elements.
*PLASTIC M2 Define the second plastic bending Unsupported
moment behavior for frame
elements.
*PLASTIC TORQUE Define the plastic torsional Unsupported
moment behavior for frame
elements.
0-1210
*POROUS BULK Define bulk moduli for soils and Property module
MODULI rocks.
*POROUS ELASTIC Specify elastic material Property module
properties for porous materials.
*POROUS FAILURE Define porous material failure Property module
CRITERIA criteria for a *POROUS METAL
PLASTICITY model.
*POROUS METAL Specify a porous metal plasticity Property module
PLASTICITY model.
*POST OUTPUT Postprocess for output from the Not applicable
restart file.
*POTENTIAL Define an anisotropic yield/creep Property module
model.
*PRELOAD HISTORY Begin the preloading definition Unsupported
of a superelement.
*PREPRINT Select printout for the solver Job module
input file processor.
*PRESSURE Specify pressure penetration Unsupported
PENETRATION loads with surface-based contact.
*PRESSURE STRESS Specify equivalent pressure stress Unsupported
as a predefined field for a mass
diffusion analysis.
*PRESTRESS HOLD Keep rebar prestress constant Unsupported
during initial equilibrium
solution.
*PRE-TENSION Associate a pre-tension node Load/BC/IC
SECTION with a pre-tension section. module
*PRINT Request or suppress output to the Step module
message file in an
ABAQUS/Standard analysis or to
the status file in an
ABAQUS/Explicit analysis.
*PSD-DEFINITION Define a cross-spectral density Unsupported
frequency function for random
response loading.
*RADIATE Specify radiation conditions in Unsupported
heat transfer analyses.
0-1211
*RADIATION FILE Define results file requests for Not applicable
cavity radiation heat transfer.
*RADIATION Define output database requests Step module
OUTPUT for cavity radiation variables.
*RADIATION PRINT Define print requests for cavity Not applicable
radiation heat transfer.
*RADIATION Define cavity symmetries for Unsupported
SYMMETRY radiation heat transfer analysis.
*RADIATION Control cavity radiation and Unsupported
VIEWFACTOR viewfactor calculations.
*RANDOM Calculate response to random Step module
RESPONSE loading.
*RATE DEPENDENT Define a rate-dependent Property module
viscoplastic model.
*RATIOS Define anisotropic swelling. Property module
*REBAR Define reinforcing in elements. Unsupported
*REFLECTION Define reflection symmetries for Unsupported
a cavity radiation heat transfer
analysis.
*RELEASE Release rotational degrees of Unsupported
freedom at one or both ends of a
beam element.
*RESPONSE Calculate the response based on Step module
SPECTRUM user-supplied response spectra.
*RESTART Save and reuse data and analysis Step module
results.
*RETAINED DOFS Specify the degrees of freedom Unsupported
that are to be retained as external
to a superelement.
*RIGID BODY Define a set of elements as a rigid Part module
body and define rigid element
properties.
*RIGID SURFACE Define an analytical rigid surface. Part module
*ROTARY INERTIA Define rigid body rotary inertia. Property module
*SECTION Specify section controls. Mesh module
CONTROLS
0-1212
*SECTION FILE Define results file requests of Not applicable
accumulated quantities on
user-defined surface sections.
*SECTION POINTS Used to locate points in the beam Unsupported
section for which axial stress and
axial strain output are required.
*SECTION PRINT Define print requests of Not applicable
accumulated quantities on
user-defined surface sections.
*SELECT CYCLIC Specify the cyclic symmetry Step module
SYMMETRY MODES modes in an eigenvalue analysis
of a cyclic symmetric structure.
*SELECT Select the eigenmodes to be used Unsupported
EIGENMODES in a modal dynamic analysis.
*SFILM Define film coefficients and Interaction
associated sink temperatures over module
a surface for heat transfer
analysis.
*SFLOW Define seepage coefficients and Unsupported
associated sink pore pressures
normal to a surface.
*SHEAR CENTER Used to define the position of the Unsupported
shear center of a beam section.
*SHEAR FAILURE Specify a shear failure model and Property module
criterion.
*SHEAR RETENTION Define the reduction of the shear Property module
modulus associated with crack
surfaces in a *CONCRETE
model as a function of the tensile
strain across the crack.
*SHEAR TEST DATA Specify the normalized shear Property module
creep compliance or relaxation
modulus as a function of time.
*SHELL GENERAL Define a general, arbitrary, elastic Property module
SECTION shell section.
*SHELL SECTION Specify a shell cross-section. Property module
*SIMPEDANCE Define impedances of acoustic Unsupported
0-1213
surfaces.
*SIMPLE SHEAR Used to provide simple shear test Property module
TEST DATA data.
*SLIDE LINE Specify slide line surfaces on Not applicable
which deformable structures may
interact.
*SLOAD Apply loads to a superelement. Unsupported
*SLOAD CASE Begin the definition of a Unsupported
superelement load case.
*SOILS Effective stress analysis for Step module
fluid-filled porous media.
*SOLID SECTION Specify element properties for Property module
solid, infinite, and truss
elements.
*SOLUBILITY Specify solubility. Property module
*SOLUTION Specify alternative solution Step module
TECHNIQUE methods.
*SOR PROPERTIES Define properties for USI SOR Unsupported
elements.
*SORPTION Define absorption and exsorption Unsupported
behavior.
*SPECIFIC HEAT Define specific heat. Property module
*SPECTRUM Define a response spectrum. Unsupported
*SPRING Define spring behavior. Unsupported
*SRADIATE Specify surface radiation Interaction
conditions in heat transfer module
analysis.
*STATIC Static stress/displacement Step module
analysis.
*STEADY STATE Steady-state dynamic response Step module
DYNAMICS based on harmonic excitation.
*STEADY STATE Specify steady-state criteria for Step module
CRITERIA terminating a quasi-static
uni-directional simulation.
*STEADY STATE Specify steady-state requirements Step module
0-1214
DETECTION for terminating a quasi-static
uni-directional simulation.
*STEADY STATE Steady-state transport analysis. Unsupported
TRANSPORT
*STEP Begin a step. Step module
*SUBMODEL Specify driven boundary nodes in Unsupported
submodeling analysis.
*SUPER Begin a Unsupported
substructure/superelement
definition.
*SUPER COPY Copy a superelement definition Unsupported
from one library to another.
*SUPER DELETE Remove a superelement from the Unsupported
superelement library.
*SUPER DIRECTORY List information about the Unsupported
superelements on a superelement
library.
*SUPER MASS Generate a reduced mass matrix Unsupported
for a superelement.
*SUPER MATRIX Write a superelement's reduced Unsupported
OUTPUT stiffness matrix, mass matrix, and
load case vectors to a file.
*SUPER PATH Move inside a substructure to Unsupported
obtain output or return back up
from within a previously entered
substructure.
*SUPER PROPERTY Translate, rotate, and/or reflect Unsupported
superelements.
*SURFACE Define a surface or region in a Surface toolset
model.
*SURFACE Define alternative Interaction
BEHAVIOR pressure-overclosure module
relationships for contact.
*SURFACE Define a surface or a region in a Surface toolset
DEFINITION model.
*SURFACE FLAW Define geometry of surface flaws. Unsupported
0-1215
*SURFACE Define surface interaction Interaction
INTERACTION properties. module
*SURFACE Define surface properties for Unsupported
PROPERTY cavity radiation.
*SWELLING Specify time-dependent Property module
volumetric swelling.
*SYMMETRIC Create a three-dimensional model Unsupported
MODEL from an axisymmetric or partial
GENERATION three-dimensional model.
*SYMMETRIC Import results from an Unsupported
RESULTS TRANSFER axisymmetric or partial
three-dimensional analysis.
*SYSTEM Specify a local coordinate system Not applicable
in which to define nodes.
*TEMPERATURE Specify temperature as a Unsupported
predefined field.
*TENSILE FAILURE Specify a tensile failure model Property module
and criterion.
*TENSION Define the retained tensile stress Property module
STIFFENING normal to a crack in a
*CONCRETE model.
*THERMAL Used to define the thermal Unsupported
EXPANSION expansion behavior of beams.
*TIE Define surface-based tie Interaction
constraint. module
*TORQUE Used to define the torsional Unsupported
behavior of beams.
*TORQUE PRINT Print a summary of the total Unsupported
torque that can be transmitted
across axisymmetric slide lines.
*TRACER PARTICLE Define tracer particles for Unsupported
tracking the location of and
results at material points during a
step.
*TRANSFORM Specify a local coordinate system Load/BC/IC
at nodes. module
*TRANSPORT Specify angular transport Unsupported
0-1216
VELOCITY velocity.
*TRANSVERSE Define transverse shear stiffness Unsupported
SHEAR STIFFNESS for beams and shells.
*TRIAXIAL TEST Used to provide triaxial test Property module
DATA data.
*TRS Used to define temperature-time Property module
shift for time history viscoelastic
analysis.
*UEL PROPERTY Define property values to be used Interaction
with a user element type. module
*UNIAXIAL TEST Used to provide uniaxial test data Property module
DATA (compression and/or tension).
*USA ADDED MASS Generate the fluid mass matrix Unsupported
GENERATION for underwater shock analysis.
*USA FLUID Define fluid variables for use in Unsupported
PROPERTIES underwater shock loading of
immersed structures.
*USA INCIDENT Specify incident pressure Unsupported
PRESSURE loading.
*USER DEFINED Redefine field variables at a Property module
FIELD material point.
*USER ELEMENT Introduce a user-defined element Interaction
type. module
*USER MATERIAL Define material constants for use Property module
in subroutine UMAT, UMATHT, or
VUMAT.
*USER OUTPUT Specify number of user variables. Property module
VARIABLES
*VARIABLE MASS Specify mass scaling during the Step module
SCALING step.
*VIEWFACTOR Write radiation viewfactors to the Unsupported
OUTPUT results file in cavity radiation
heat transfer analysis.
*VISCO Transient, static, Step module
stress/displacement analysis with
time-dependent material response
(creep, swelling, and
0-1217
viscoelasticity).
*VISCOELASTIC Specify dissipative behavior for Property module
use with elasticity.
*VOID NUCLEATION Define the nucleation of voids in Property module
a porous material.
*VOLUMETRIC TEST Provide volumetric test data. Property module
DATA
*WAVE Define gravity waves for use in Unsupported
immersed structure calculations.
*WAVEFRONT Minimize the wavefront for the Not applicable
MINIMIZATION frontal solver.
*WIND Define wind velocity profile for Unsupported
wind loading.
0-1218
DENSITY, ELSET, POISSON, SECTION (All values except: CIRC, HEX, L,
RECTANGULAR, TRAPEZOID, NONLINEAR GENERAL ), ZERO
*BEAM SECTION
DENSITY, ELSET, MATERIAL, POISSON, SECTION (All values except: CIRC, HEX,
L, RECTANGULAR, TRAPEZOID ), TEMPERATURE, ZERO
*BIAXIAL TEST DATA (No parameters)
*BOND: Not supported
*BOUNDARY
AMPLITUDE, FIXED, OP, TYPE
*BRITTLE CRACKING: Not supported
*BRITTLE FAILURE: Not supported
*BRITTLE SHEAR: Not supported
*BUCKLE
EIGENSOLVER
*BUCKLING ENVELOPE: Not supported
*BUCKLING LENGTH: Not supported
*BUCKLING REDUCTION FACTORS: Not supported
*BULK VISCOSITY (No parameters)
*C ADDED MASS: Not supported
*CAP CREEP
DEPENDENCIES, LAW (All values except: USER ), MECHANISM
*CAP HARDENING
DEPENDENCIES
*CAP PLASTICITY
DEPENDENCIES
*CAST IRON COMPRESSION HARDENING: Not supported
*CAST IRON PLASTICITY: Not supported
*CAST IRON TENSION HARDENING: Not supported
*CAVITY DEFINITION: Not supported
*CECHARGE: Not supported
*CECURRENT: Not supported
*CENTROID (No parameters)
*CFILM: Not supported
*CFLUX: Not supported
*CHANGE FRICTION
0-1219
INTERACTION, RESET
*CLAY HARDENING
DEPENDENCIES
*CLAY PLASTICITY
DEPENDENCIES, HARDENING, INTERCEPT
*CLEARANCE: Not supported
*CLOAD
AMPLITUDE, FOLLOWER, OP
*COMBINED TEST DATA
SHRINF, VOLINF
*CONCRETE
DEPENDENCIES
*CONDUCTIVITY
DEPENDENCIES, TYPE
*CONNECTOR BEHAVIOR: Not supported
*CONNECTOR CONSTITUTIVE REFERENCE: Not supported
*CONNECTOR DAMPING: Not supported
*CONNECTOR ELASTICITY: Not supported
*CONNECTOR FAILURE: Not supported
*CONNECTOR FRICTION: Not supported
*CONNECTOR LOAD: Not supported
*CONNECTOR LOCK: Not supported
*CONNECTOR MOTION: Not supported
*CONNECTOR SECTION: Not supported
*CONNECTOR STOP: Not supported
*CONTACT CONTROLS: Not supported
*CONTACT DAMPING
DEFINITION, TANGENT FRACTION
*CONTACT FILE: Not supported
*CONTACT INTERFERENCE
OP, SHRINK, AMPLITUDE
*CONTACT NODE SET: Not supported
*CONTACT OUTPUT
NSET
*CONTACT PAIR
0-1220
INTERACTION, ADJUST, SMALL SLIDING, TIED, CPSET, OP, HCRIT
*CONTACT PRINT: Not supported
*CONTACT RESPONSE: Not supported
*CONTOUR INTEGRAL: Not supported
*CONTROLS: Not supported
*CORRELATION: Not supported
*COUPLED TEMPERATURE-DISPLACEMENT
CETOL, DELTMX, EXPLICIT, NO CREEP, STEADY STATE, STABILIZE, CREEP
*COUPLED THERMAL-ELECTRICAL
DELTMX, END, MXDEM, STEADY STATE
*CRADIATE: Not supported
*CREEP
DEPENDENCIES, LAW (All values except: USER )
*CREEP STRAIN RATE CONTROL: Not supported
*CYCLED PLASTIC (No parameters)
*CYCLIC: Not supported
*CYCLIC HARDENING
DEPENDENCIES, PARAMETERS
*CYCLIC SYMMETRY MODEL: Not supported
*D ADDED MASS: Not supported
*DAMPING
ALPHA, BETA, COMPOSITE
*DASHPOT: Not supported
*DEBOND: Not supported
*DECHARGE: Not supported
*DECURRENT: Not supported
*DEFORMATION PLASTICITY (No parameters)
*DENSITY
DEPENDENCIES
*DEPVAR
DELETE
*DESIGN GRADIENT: Not supported
*DESIGN PARAMETER: Not supported
*DESIGN RESPONSE: Not supported
*DESIGN SHAPE VARIATION: Not supported
0-1221
*DESIGN VALUE: Not supported
*DESIGN VARIATION: Not supported
*DETONATION POINT: Not supported
*DFLOW: Not supported
*DFLUX: Not supported
*DIAGNOSTICS: Not supported
*DIELECTRIC
TYPE
*DIFFUSIVITY
DEPENDENCIES, LAW, TYPE
*DISTRIBUTING COUPLING: Not supported
*DLOAD
AMPLITUDE, OP
*DRAG CHAIN: Not supported
*DRUCKER PRAGER
DEPENDENCIES, ECCENTRICITY, SHEAR CRITERION, TEST DATA
*DRUCKER PRAGER CREEP
DEPENDENCIES, LAW (All values except: USER )
*DRUCKER PRAGER HARDENING
DEPENDENCIES, RATE, TYPE
*DSA CONTROLS: Not supported
*DSECHARGE: Not supported
*DSECURRENT: Not supported
*DSFLOW: Not supported
*DSFLUX: Not supported
*DSLOAD
AMPLITUDE, OP
*DYNAMIC
ADIABATIC, ALPHA, HAFTOL, DIRECT USER CONTROL, ELEMENT BY ELEMENT,
EXPLICIT, FIXED TIME INCREMENTATION, INITIAL, NOHAF, SCALE FACTOR
*DYNAMIC TEMPERATURE-DISPLACEMENT
DIRECT USER CONTROL, ELEMENT BY ELEMENT, EXPLICIT, FIXED TIME
INCREMENTATION, SCALE FACTOR
*EL FILE: Not supported
*EL HISTORY: Not supported
*EL PRINT: Not supported
0-1222
*ELASTIC
DEPENDENCIES, MODULI, TYPE
*ELCOPY: Not supported
*ELECTRICAL CONDUCTIVITY
DEPENDENCIES, TYPE
*ELEMENT
TYPE, ELSET
*ELEMENT MATRIX OUTPUT: Not supported
*ELEMENT OUTPUT
ELSET
*ELEMENT RESPONSE: Not supported
*ELGEN
ALL NODES, ELSET
*ELSET
ELSET, GENERATE, INSTANCE, INTERNAL, TYPE
*EMISSIVITY: Not supported
*END ASSEMBLY (No parameters)
*END INSTANCE (No parameters)
*END PART (No parameters)
*END PRELOAD: Not supported
*END STEP (No parameters)
*END SUPER: Not supported
*ENERGY FILE: Not supported
*ENERGY HISTORY: Not supported
*ENERGY OUTPUT (No parameters)
*ENERGY PRINT: Not supported
*EOS: Not supported
*EOS SHEAR: Not supported
*EPJOINT: Not supported
*EQUATION: Not supported
*EXPANSION
DEPENDENCIES, PORE FLUID, TYPE, ZERO
*EXTREME ELEMENT VALUE: Not supported
*EXTREME NODE VALUE: Not supported
0-1223
*EXTREME VALUE: Not supported
*FAIL STRAIN
DEPENDENCIES
*FAIL STRESS
DEPENDENCIES
*FAILURE RATIOS
DEPENDENCIES
*FIELD: Not supported
*FILE FORMAT: Not supported
*FILE OUTPUT: Not supported
*FILM: Not supported
*FILM PROPERTY: Not supported
*FIXED MASS SCALING
DT, ELSET, FACTOR, TYPE
*FLOW: Not supported
*FLUID BULK MODULUS: Not supported
*FLUID DENSITY: Not supported
*FLUID EXPANSION: Not supported
*FLUID FLUX: Not supported
*FLUID LINK: Not supported
*FLUID PROPERTY: Not supported
*FOAM
DEPENDENCIES, HARDENING
*FOAM HARDENING
DEPENDENCIES
*FOUNDATION (No parameters)
*FRACTURE CRITERION: Not supported
*FRAME SECTION: Not supported
*FREQUENCY
EIGENSOLVER
*FRICTION
ANISOTROPIC, DEPENDENCIES, DEPVAR, ELASTIC SLIP, EXPONENTIAL DECAY,
LAGRANGE, PROPERTIES, ROUGH, SHEAR TRACTION SLOPE, SLIP TOLERANCE,
TAUMAX, TEST DATA, USER
*GAP: Not supported
0-1224
*GAP CONDUCTANCE
DEPENDENCIES, PRESSURE, USER
*GAP ELECTRICAL CONDUCTANCE: Not supported
*GAP FLOW: Not supported
*GAP HEAT GENERATION (No parameters)
*GAP RADIATION (No parameters)
*GASKET BEHAVIOR
NAME
*GASKET CONTACT AREA
DEPENDENCIES
*GASKET ELASTICITY
COMPONENT, DEPENDENCIES, VARIABLE
*GASKET SECTION
BEHAVIOR, ELSET, MATERIAL, STABILIZATION STIFFNESS
*GASKET THICKNESS BEHAVIOR
DEPENDENCIES, DIRECTION, SLOPE DROP, TENSILE STIFFNESS FACTOR, TYPE,
VARIABLE, YIELD ONSET
*GEL (No parameters)
*GEOSTATIC (No parameters)
*HEADING (No parameters)
*HEAT GENERATION (No parameters)
*HEAT TRANSFER
DELTMX, END, MXDEM, STEADY STATE
*HEATCAP: Not supported
*HISTORY OUTPUT: Not supported
*HOURGLASS CONTROL: Not supported
*HOURGLASS STIFFNESS: Not supported
*HYPERELASTIC
ARRUDA-BOYCE, BETA, MOONEY-RIVLIN, MODULI, N, OGDEN, POLYNOMIAL,
PROPERTIES, REDUCED POLYNOMIAL, TEST DATA INPUT, TYPE, USER, VAN DER
WAALS, YEOH
*HYPERFOAM
N, POISSON, TEST DATA INPUT
*HYPOELASTIC
USER
*HYSTERESIS: Not supported
0-1225
*IMPEDANCE: Not supported
*IMPEDANCE PROPERTY: Not supported
*IMPERFECTION: Not supported
*IMPORT: Not supported
*IMPORT CONTROLS: Not supported
*IMPORT ELSET: Not supported
*IMPORT NSET: Not supported
*INCLUDE (No parameters)
*INCREMENTATION OUTPUT (No parameters)
*INELASTIC HEAT FRACTION (No parameters)
*INITIAL CONDITIONS
TYPE (All values except: CONCENTRATION, CONTACT, FIELD, FLUID
PRESSURE, HARDENING, MASS FLOW RATE, NONAXI, OLD MESH, PORE
PRESSURE, PRESSURE STRESS, RATIO, RELATIVE DENSITY, ROTATING
VELOCITY, SATURATION, SOLUTION, SPUD EMBEDMENT, SPUD PRELOAD,
STRESS )
*INSTANCE
NAME, PART
*INTERFACE: Not supported
*ITS: Not supported
*JOINT: Not supported
*JOINT ELASTICITY: Not supported
*JOINT PLASTICITY: Not supported
*JOINTED MATERIAL: Not supported
*JOULE HEAT FRACTION (No parameters)
*KAPPA
DEPENDENCIES, TYPE (All values except: PRESS)
*KINEMATIC COUPLING: Not supported
*LATENT HEAT (No parameters)
*M1: Not supported
*M2: Not supported
*MAP SOLUTION: Not supported
*MASS: Not supported
*MASS DIFFUSION
DCMAX, END, STEADY STATE
0-1226
*MASS FLOW RATE: Not supported
*MATERIAL
NAME
*MATRIX: Not supported
*MEMBRANE SECTION
ELSET, MATERIAL
*MODAL DAMPING: Not supported
*MODAL DYNAMIC: Not supported
*MODAL FILE: Not supported
*MODAL OUTPUT (No parameters)
*MODAL PRINT: Not supported
*MODEL CHANGE
ADD, REMOVE, TYPE (All values except: ELEMENT )
*MOHR COULOMB: Not supported
*MOHR COULOMB HARDENING: Not supported
*MOISTURE SWELLING (No parameters)
*MONITOR
DOF, FREQUENCY, NODE
*MOTION: Not supported
*MPC: Not supported
*NCOPY: Not supported
*NFILL
BIAS, NSET, SINGULAR, TWO STEP
*NGEN
LINE, NSET
*NMAP: Not supported
*NO COMPRESSION: Not supported
*NO TENSION: Not supported
*NODAL THICKNESS: Not supported
*NODE
NSET, SYSTEM
*NODE FILE: Not supported
*NODE HISTORY: Not supported
*NODE OUTPUT
NSET
0-1227
*NODE PRINT: Not supported
*NODE RESPONSE: Not supported
*NORMAL: Not supported
*NSET
GENERATE, INSTANCE, INTERNAL, NSET, TYPE
*ORIENTATION: Not supported
*ORNL
A, H, MATERIAL, RESET
*OUTPUT
FIELD, FREQUENCY, HISTORY, MODE LIST, NUMBER INTERVAL, OP, TIME
INTERVAL, TIME MARKS
*PARAMETER: Not supported
*PARAMETER DEPENDENCE: Not supported
*PARAMETER SHAPE VARIATION: Not supported
*PART
NAME
*PERIODIC: Not supported
*PERMEABILITY
SPECIFIC, TYPE
*PHYSICAL CONSTANTS: Not supported
*PIEZOELECTRIC
TYPE
*PIPE-SOIL INTERACTION: Not supported
*PIPE-SOIL STIFFNESS: Not supported
*PLANAR TEST DATA (No parameters)
*PLASTIC
DATA TYPE, DEPENDENCIES, HARDENING (All values except: COMBINED,
JOHNSON COOK ), RATE
*PLASTIC AXIAL: Not supported
*PLASTIC M1: Not supported
*PLASTIC M2: Not supported
*PLASTIC TORQUE: Not supported
*POROUS BULK MODULI (No parameters)
*POROUS ELASTIC
DEPENDENCIES, SHEAR
0-1228
*POROUS FAILURE CRITERIA (No parameters)
*POROUS METAL PLASTICITY
DEPENDENCIES, RELATIVE DENSITY
*POST OUTPUT: Not supported
*POTENTIAL
DEPENDENCIES
*PRE-TENSION SECTION: Not supported
*PRELOAD HISTORY: Not supported
*PREPRINT (No parameters)
*PRESSURE PENETRATION: Not supported
*PRESSURE STRESS: Not supported
*PRESTRESS HOLD: Not supported
*PRINT
ALLKE, CONTACT, CRITICAL ELEMENT, DMASS, ETOTAL, FREQUENCY,
PLASTICITY, RESIDUAL, SOLVE
*PSD-DEFINITION: Not supported
*RADIATE: Not supported
*RADIATION FILE: Not supported
*RADIATION OUTPUT (No parameters)
*RADIATION PRINT: Not supported
*RADIATION SYMMETRY: Not supported
*RADIATION VIEWFACTOR: Not supported
*RANDOM RESPONSE: Not supported
*RATE DEPENDENT
DEPENDENCIES, TYPE
*RATIOS
DEPENDENCIES
*REACTIVE ACOUSTIC SURFACE: Not supported
*REBAR: Not supported
*REFLECTION: Not supported
*RELEASE: Not supported
*RESPONSE SPECTRUM: Not supported
*RESTART
WRITE, FREQUENCY, OVERLAY, NUMBER INTERVAL, TIME MARKS
*RETAINED DOFS: Not supported
0-1229
*RIGID BODY
ANALYTICAL SURFACE, ELSET, REF NODE
*RIGID SURFACE
TYPE (All values except: USER ), NAME, REF NODE
*ROTARY INERTIA: Not supported
*SECTION CONTROLS: Not supported
*SECTION FILE: Not supported
*SECTION POINTS (No parameters)
*SECTION PRINT: Not supported
*SELECT CYCLIC SYMMETRY MODES: Not supported
*SELECT EIGENMODES: Not supported
*SFILM: Not supported
*SFLOW: Not supported
*SHEAR CENTER (No parameters)
*SHEAR FAILURE: Not supported
*SHEAR RETENTION
DEPENDENCIES
*SHEAR TEST DATA
SHRINF
*SHELL GENERAL SECTION
ELSET, MATERIAL, POISSON
*SHELL SECTION
ELSET, MATERIAL, POISSON, SECTION INTEGRATION, TEMPERATURE
*SIMPEDANCE: Not supported
*SIMPLE SHEAR TEST DATA (No parameters)
*SLIDE LINE: Not supported
*SLIDE PLANE: Not supported
*SLOAD: Not supported
*SLOAD CASE: Not supported
*SOILS
CETOL, CONSOLIDATION, END, NO CREEP, UTOL, STABILIZE
*SOLID SECTION
ELSET, MATERIAL
*SOLUBILITY
DEPENDENCIES
0-1230
*SOLUTION TECHNIQUE
TYPE (All values except: QUASI-NEWTON )
*SOR PROPERTIES: Not supported
*SORPTION: Not supported
*SPECIFIC HEAT
DEPENDENCIES
*SPECTRUM: Not supported
*SPHEX: Not supported
*SPRING: Not supported
*SRADIATE: Not supported
*STATIC
ADIABATIC, DIRECT, FULLY PLASTIC, RIKS, STABILIZE
*STEADY STATE CRITERIA: Not supported
*STEADY STATE DETECTION: Not supported
*STEADY STATE DYNAMICS: Not supported
*STEADY STATE TRANSPORT: Not supported
*STEP
AMPLITUDE, EXTRAPOLATION, INC, NLGEOM, PERTURBATION, UNSYMM, NAME
*SUBMODEL: Not supported
*SUPER: Not supported
*SUPER COPY: Not supported
*SUPER DELETE: Not supported
*SUPER DIRECTORY: Not supported
*SUPER MASS: Not supported
*SUPER MATRIX OUTPUT: Not supported
*SUPER PATH: Not supported
*SUPER PROPERTY: Not supported
*SURFACE
NAME, TYPE (All values except: NODE, USER )
*SURFACE BEHAVIOR
NO SEPARATION, PRESSURE-OVERCLOSURE
*SURFACE DEFINITION
NAME
*SURFACE FLAW: Not supported
*SURFACE IMPEDANCE: Not supported
0-1231
*SURFACE INTERACTION
NAME
*SURFACE PROPERTY (No parameters)
*SWELLING
DEPENDENCIES, LAW (All values except: USER )
*SYMMETRIC MODEL GENERATION: Not supported
*SYMMETRIC RESULTS TRANSFER: Not supported
*SYSTEM (No parameters)
*TEMPERATURE: Not supported
*TENSILE FAILURE: Not supported
*TENSION STIFFENING
DEPENDENCIES, TYPE
*THERMAL EXPANSION: Not supported
*TIE: Not supported
*TORQUE: Not supported
*TORQUE PRINT: Not supported
*TRACER PARTICLE: Not supported
*TRANSFORM: Not supported
*TRANSPORT VELOCITY: Not supported
*TRANSVERSE SHEAR STIFFNESS: Not supported
*TRIAXIAL TEST DATA
A, B, PT
*TRS
DEFINITION (All values except: USER )
*UEL PROPERTY: Not supported
*UNIAXIAL TEST DATA (No parameters)
*USA ADDED MASS GENERATION (No parameters)
*USA FLUID PROPERTIES: Not supported
*USA INCIDENT PRESSURE: Not supported
*USER DEFINED FIELD (No parameters)
*USER ELEMENT: Not supported
*USER GASKET BEHAVIOR: Not supported
*USER MATERIAL
CONSTANTS, TYPE, UNSYMM
0-1232
*USER OUTPUT VARIABLES (No parameters)
*USER SUBROUTINES: Not supported
*VARIABLE MASS SCALING
DIRECTION, DT, ELSET, FREQUENCY, TYPE, NUMBER INTERVAL
*VIEWFACTOR OUTPUT: Not supported
*VISCO
CETOL, EXPLICIT, STABILIZE, CREEP
*VISCOELASTIC
ERRTOL, FREQUENCY, NMAX, TIME
*VOID NUCLEATION
DEPENDENCIES
*VOLUMETRIC TEST DATA
VOLINF
*WAVE: Not supported
*WAVEFRONT MINIMIZATION: Not supported
*WIND: Not supported
0-1233
Appendix B: Visualization module limitations
This section lists output variables not supported by the Visualization module.
0-1234
SOE Total current across the section.
SOF Total force in the section.
SOH Total heat flux across the section.
SOM Total moment in the section.
SOP Total pore fluid volume flux across the section.
SS, SSn Substresses for ITS elements.
SSAVGn Average shell section stress component n.
TPFL Total pore fluid volume flux leaving the slave surface.
TPTL Time integrated TPFL.
0-1235
Appendix C: Transitioning to the Visualization
module from ABAQUS/Post
This section compares the functionality of the Visualization module with that of ABAQUS/Post. For
each ABAQUS/Post command the related functionality within the Visualization module is discussed.
The following topics are covered:
· ``General differences between the Visualization module and ABAQUS/Post,'' Section C.1
· Perspective is on.
· All model plots (including undeformed) show title and state information.
· Wireframe render style can be used during cursor-controlled panning, zooming, and rotating.
You can customize these and other Visualization module display characteristics, emulating
ABAQUS/Post if you choose. In general, the Visualization module offers features and options
extending beyond those available in ABAQUS/Post; however, in some cases functionality supported
by ABAQUS/Post is not yet available in the Visualization module. A detailed comparison of
functionality is given in ``Visualization module functionality corresponding to each top-level
0-1236
ABAQUS/Post command,'' Section C.2, and ``Visualization module functionality corresponding to
each ABAQUS/Post SET/SHOW parameter,'' Section C.3.
*ANIMATE
To access this functionality in the Visualization module, use the Animate menu in the main
menu bar. Differences between *ANIMATE in ABAQUS/Post and animation in the
Visualization module are as follows:
· The ABAQUS/Post *ANIMATE command plays back a series of captured images; the
images can be any combination of ABAQUS/Post plots. In contrast, the Visualization
module animation plays either a previously saved animation file or an automatically
generated sequence of deformed, contour, or symbol plot images. Automatically generated
sequences can show results varying over time or results varying by scale factor. You can
customize these images as they are generated, but you cannot capture arbitrary
combinations of plots.
· In the Visualization module you can play more than one animation at once using multiple
viewports.
· In the Visualization module you can change customization options, and you can change
the viewpoint while an automatically generated sequence is playing.
To learn more about animation in the Visualization module, see Chapter 34, "Animating
plots."
*BC DISPLAY
To access this functionality in the Visualization module, click View->ODB Display
Options->BC. You cannot customize the display of boundary conditions in the Visualization
module.
*BC STYLE
This feature is not supported in the Visualization module.
*COLOR SET
To access this functionality in the Visualization module, click Tools->Color Code.
Differences between the *COLOR SET command in ABAQUS/Post and color coding in the
Visualization module are as follows:
· The Visualization module extends this feature to allow color coding based on results and
picking of elements directly from the viewport.
· In ABAQUS/Post you can assign separate colors to selected nodes; the color is applied to
the node symbols. This feature is not supported in the Visualization module.
0-1237
· In ABAQUS/Post you can specify separate colors for each element face. This feature is
not supported in the Visualization module.
· The ABAQUS/Post *COLOR SET command can be used to control the translucency of
element sets; in the Visualization module translucency is controlled using plot
mode-dependent options, and it applies to the overall model or, for contour plots, to
elements having no results.
To learn more about color coding in the Visualization module, see ``Coloring individual
elements and surfaces,'' Section 37.4.
*COLOR TABLE
This feature is not supported in the Visualization module.
*CONTOUR
To produce a contour plot in the Visualization module, click Plot->Contour. To access the
functionality of the ABAQUS/Post *CONTOUR, RANGE feature, click Report->Field
Output. Differences between *CONTOUR in ABAQUS/Post and contour plotting in the
Visualization module are as follows:
· In ABAQUS/Post contour values are determined using elements on the exterior surface of
the model only. In the Visualization module values from all elements in the active display
group are used to compute contours.
· In ABAQUS/Post you have limited control over nodal averaging; the Visualization
module offers extensive nodal averaging options.
· In ABAQUS/Post nodal averaged tensor invariants are computed from the nodal averaged
tensor components. In the Visualization module nodal averaged tensor invariants are
computed at the element level using the extrapolated tensor components, and the resulting
element-nodal invariants are averaged at the nodes. For more information on how the
Visualization module computes the invariants, see ``Understanding how results are
computed,'' Section 24.4.1.
· In the Visualization module you can produce a contour plot of nodal discontinuities; this
feature is not available in ABAQUS/Post.
· In ABAQUS/Post you can specify only one section point from which to read results for all
shells, beams, and layered solids included in the plot. In the Visualization module you can
specify a separate section point for each category of beam and shell included in the plot.
0-1238
computation are not subject to your control; the Visualization module allows you to
control aspects of this computation.
· In the Visualization module you can specify the color of the curves in a tick mark contour
plot; in ABAQUS/Post the curves in a tick mark contour plot are always displayed in
white.
· In the Visualization module tick marks are plotted in model space. In ABAQUS/Post they
are plotted in the plane of the screen.
· In the Visualization module you can specify the normal direction in which tick mark
contour plot axes will be drawn on beam elements; this feature is not available in
ABAQUS/Post.
For more information, see Chapter 27, "Contouring analysis results," and Chapter 35,
"Generating tabular data reports."
*CRACK
This feature is not supported in the Visualization module.
*CSET
This feature is not supported in the Visualization module. However, X-Y data objects and
curves in X-Y graphs can be multiply selected from displays in the Visualization module.
*CURVE STYLE
To access this functionality in the Visualization module, click Options->XY Curve. For more
information, see ``Customizing X-Y curve appearance,'' Section 30.6.
*DEFINE CURVE
To access this functionality in the Visualization module, click Tools->XY
Data->Create->Operate on XY Data->data object. Differences in this functionality are as
follows:
· The Visualization module offers a more extensive set of operations than those in
ABAQUS/Post.
· In ABAQUS/Post you can apply only one operation per curve definition; in the
Visualization module you can combine multiple operations to define a new X-Y data
object.
· The behavior of those operations available in both the Visualization module and
ABAQUS/Post is the same with the exception of curve smoothing. In ABAQUS/Post for
*DEFINE CURVE, OPERATION=SMOOTH you specify the total number of data points
to be included in the moving average; in the Visualization module the smooth(X,I)
operation interprets the number you specify as the number of data points to include on
each side of the current point.
0-1239
For more information, see ``Operating on saved X-Y data objects,'' Section 30.4.3.
*DELETE CURVE
To access this functionality in the Visualization module, click Tools->XY Data->Manager or
Tools->XY Data->Delete->data object. The Data Manager facilitates curve selection by
providing curve descriptions, including information about the origin of the data.
For more information, see ``Managing objects,'' Section 6.5.
*DETAIL
To access this functionality in the Visualization module, click Tools->Display Group.
Differences between *DETAIL in ABAQUS/Post and display groups in the Visualization
module are as follows:
· In ABAQUS/Post you cannot name the detail and, hence, cannot refer to it again in the
same session. The Visualization module allows you to name the display group, and you
can save it for future use in the current session.
· An ABAQUS/Post detail includes all elements, nodes, and surfaces contained in the sets
referred to by the ELSET, NSET, and SURFACE parameters. You can vary the contents
of the detail by specifying different sets or, indirectly, by applying the equivalent of the
Boolean operators Remove and Add to existing sets. In contrast, the Visualization
module directly allows most Boolean operations when working with display groups,
including Intersect, Remove, Either, etc.
· The Visualization module extends this feature to allow the creation of display groups
based on results and the picking of elements and nodes directly from the viewport.
· In ABAQUS/Post if you open a new restart (.res) file, the detail settings associated
with the previous file are lost. However, in the Visualization module you can save display
groups for future use in the current session, and you can apply them to other output
database files as long as they are valid.
To learn more about display groups in the Visualization module, see Chapter 36, "Displaying a
subset of your model."
*DISPLAY CURVE
To access this functionality in the Visualization module, click Tools->XY Data->Manager or
Tools->XY Data->Plot. The Data Manager facilitates curve selection by providing curve
descriptions, including information about the origin of the data.
To learn more about X-Y plotting in the Visualization module, see Chapter 30, "X-Y plotting."
*DRAW
0-1240
To access functionality comparable to the ABAQUS/Post *DRAW command, click
Plot->Undeformed Shape . For more information, see Chapter 25, "Plotting the undeformed
shape." To access functionality comparable to the ABAQUS/Post *DRAW, DISPLACED
command, click Plot->Deformed Shape. For more information, see Chapter 26, "Plotting the
deformed shape." Differences in functionality are as follows:
· The variable that will be used to produce the deformed shape is specified in
ABAQUS/Post as a parameter of the *DRAW command; in the Visualization module this
variable is specified separately, in the Field Output dialog box.
· In the Visualization module you can choose separate customization options for normals on
undeformed and deformed model plots. For more information, see ``Displaying element
and surface normals,'' Section 37.7. (Separate customization is not available in
ABAQUS/Post.)
· The ABAQUS/Post capability to draw section points through the thickness for layered
solid elements is not supported by the Visualization module.
*ELSET
To access this functionality in the Visualization module, click Tools->Display Group.
Differences between *ELSET in ABAQUS/Post and display groups in the Visualization
module are as follows:
· ABAQUS/Post element sets can contain only elements; the Visualization module display
groups can contain any combination of elements, nodes, and surfaces.
· The Visualization module extends this feature to allow the creation of display groups
based on results and the picking of elements directly from the viewport.
· In ABAQUS/Post you can color element sets using the *COLOR SET command. In the
Visualization module you can color selected elements and element sets using
Tools->Color Code.
· ABAQUS/Post element sets support only the add, remove, and delete operations. The
Visualization module display groups support numerous Boolean operations and can be
copied and renamed.
· ABAQUS/Post element sets can be defined based on bounding model coordinate values.
This feature is not supported by the Visualization module.
0-1241
To learn more about display groups in the Visualization module, see Chapter 36, "Displaying a
subset of your model."
*END
To access this functionality in the Visualization module, click File->Exit.
For more information, see ``Exiting an ABAQUS/CAE session,'' Section 5.1.2.
*FONT
This functionality is supported in the Visualization module by the Select Font dialog box,
which is available from every dialog box in which font specification is meaningful.
Differences between *FONT in ABAQUS/Post and font support in the Visualization module
are as follows:
· ABAQUS/Post font specification applies only to the title text; the Visualization module
supports font specification for all screen text, including: model labels, legends, axes
labels, graph labels, title blocks, state blocks, and annotations.
· ABAQUS/Post provides only two font choices; the Visualization module offers
system-dependent font customization options.
*GRAPH AXES
To access this functionality in the Visualization module, click Options->XY Graph.
Differences between *GRAPH AXES in ABAQUS/Post and the XY Graph options in the
Visualization module are as follows:
· In ABAQUS/Post you specify the interval between tick marks; the Visualization module
extends this feature, allowing you to alternatively specify the total number of tick marks.
· In the Visualization module you can choose the format of the numeric axis labels. (This
feature is not available in ABAQUS/Post.)
· In the Visualization module you can customize the thickness of the graph axes and grid
lines. (This feature is not available in ABAQUS/Post.)
· In the Visualization module you can customize the font of each axis title. (This feature is
not available in ABAQUS/Post.)
For more information, see ``Customizing X-Y plot axes,'' Section 30.5.
*GRAPH LEGEND
To access this functionality in the Visualization module, click View->Viewport
Annotations->Legend. The Visualization module extends this functionality to include legend
font specification.
For more information, see ``Customizing the legend,'' Section 38.1.
0-1242
*HELP
To access this functionality in the Visualization module, click Help. The Visualization module
help consists of an extensive online ``electronic book'' that you can browse and search;
context-sensitive help is also available.
For more information, see ``Getting help,'' Section 5.6.
*INPUT
This feature is not supported in the Visualization module.
*LOAD DISPLAY
This feature is not supported in the Visualization module.
*LOAD STYLE
This feature is not supported in the Visualization module.
*NSET
To access this functionality in the Visualization module, click Tools->Display Group.
Differences between *NSET in ABAQUS/Post and display groups in the Visualization module
are as follows:
· ABAQUS/Post node sets can contain only nodes; the Visualization module display groups
can contain any combination of elements, nodes, and surfaces.
· The Visualization module extends this feature to allow the creation of display groups
based on results and the picking of nodes directly from the viewport.
· ABAQUS/Post node sets support only the add operation. The Visualization module
display groups support numerous Boolean operations and can be copied and renamed.
· ABAQUS/Post node sets can be referenced by the *READ CURVE command to specify
X-Y data to be read. This feature is not directly supported by the Visualization module;
however, multiple selection provides similar functionality.
· ABAQUS/Post node sets can be referenced by the *COLOR SET command to assign a
display color to the node symbols. In the Visualization module nodes and node sets cannot
be assigned a display color.
To learn more about display groups in the Visualization module, see Chapter 36, "Displaying a
subset of your model."
*PATH
To access this functionality in the Visualization module, you first specify a path by clicking
Tools->Path and then obtain X-Y data along the path by clicking Tools->XY Data.
Differences between the *PATH command in ABAQUS/Post and the path tool in the
Visualization module are as follows:
0-1243
· In the Visualization module you can display the path itself.
· The Visualization module automates the inclusion of nodal coordinates during path
definition.
· The Visualization module provides options to control the averaging of field output results
along the path.
· In ABAQUS/Post paths defined by points (straight paths) are limited to two points; in the
Visualization module point list paths can contain any number of points that need not form
a straight line.
For more information, see Chapter 32, "Viewing results along a path."
*PAUSE
This feature is not supported in the Visualization module.
*PRINT CURVE
To access this functionality in the Visualization module, click Report->XY. In addition to the
ABAQUS/Post functionality, the Visualization module offers extensive options for value
formatting, table layout, results combination, and column tabulation. For more information,
see Chapter 35, "Generating tabular data reports."
*PRINT ELEMENTS
To access this functionality in the Visualization module, click Tools->Query; then select
Probe values. Unlike ABAQUS/Post, the Visualization module allows you to probe elements
and selectively write the resulting values to a file. In the Visualization module the display of
material names is not supported. For more information, see Chapter 31, "Querying and
probing."
*PRINT NODES
To access this functionality in the Visualization module, click Tools->Query; then select
Probe values. Unlike ABAQUS/Post, the Visualization module allows you to probe nodes
and selectively write the resulting values to a file. For more information, see Chapter 31,
"Querying and probing."
*PRINT VALUES
To access this functionality in the Visualization module, click Tools->Query; then select
Probe values. Unlike ABAQUS/Post, the Visualization module allows you to probe values
and selectively write them to a file. For more information, see Chapter 31, "Querying and
probing."
In addition to probing and writing selected values to a file, in the Visualization module you
can produce a tabular report of values for a specified variable. To access this functionality,
click Report->Field Output. The Visualization module offers extensive options for value
formatting, table layout, results combination, and column tabulation. For more information,
0-1244
see Chapter 35, "Generating tabular data reports."
*READ CURVE
To access this functionality in the Visualization module, click Tools->XY Data->Manager or
Tools->XY Data->Create.
To learn more about X-Y plotting in the Visualization module, see ``Specifying and saving
X-Y data objects,'' Section 30.2.
*REPORT ELEMENTS
To access this functionality in the Visualization module, click Tools->Query; then select
Probe values. The Visualization module highlights elements as you position the cursor over
them. Unlike ABAQUS/Post, the Visualization module allows you to probe elements and
selectively write values to a file. In the Visualization module the display of material names is
not supported. For more information, see Chapter 31, "Querying and probing."
*REPORT NODES
To access this functionality in the Visualization module, click Tools->Query; then select
Probe values. The Visualization module highlights nodes as you position the cursor over
them. Unlike ABAQUS/Post, the Visualization module allows you to probe nodes and
selectively write values to a file. For more information, see Chapter 31, "Querying and
probing."
*REPORT VALUES
To access this functionality in the Visualization module, click Tools->Query; then select
Probe values. The Visualization module highlights nodes or elements as you position the
cursor over them. Unlike ABAQUS/Post, the Visualization module allows you to probe values
and selectively write them to a file. In the Visualization module you can choose the output
position at which to calculate results. For more information, see Chapter 31, "Querying and
probing."
*REPORT XY VALUES
To access this functionality in the Visualization module, click Tools->Query; then select
Probe values. Unlike ABAQUS/Post, the Visualization module allows you to probe X-Y
values and selectively write them to a file. For more information, see Chapter 31, "Querying
and probing."
*RESET
To access this functionality in the Visualization module, click the Defaults button available in
every dialog box where defaults are meaningful.
*RESTART
To open a file containing model data and analysis results in the Visualization module, click
File->Open. Unlike ABAQUS/Post, the Visualization module reads all model data and
0-1245
analysis results from a single file, the output database. See ``Opening a model database or an
output database,'' Section 12.6.2, to learn more about opening output database files.
To select the equivalent of an ABAQUS/Post restart STEP and INCREMENT, click
Results->Frame. For more information, see Chapter 24, "Selecting model data and analysis
results to plot."
*RESULTS FILE
This functionality is not applicable to the Visualization module.
*SEQUENCE
In ABAQUS/Post the *SEQUENCE command is used to display a series of plots in succession
and to facilitate the generation of an animation file. Comparable functionality in the
Visualization module is as follows:
To learn more about animation in the Visualization module, see Chapter 34, "Animating
plots."
*SET
To access this functionality in the Visualization module, click the Options menu or click the
various toolbar icons. A detailed explanation of the differences between the *SET parameters
in ABAQUS/Post and the customization options in the Visualization module is given in
``Visualization module functionality corresponding to each ABAQUS/Post SET/SHOW
parameter,'' Section C.3.
*SHOW
To access this functionality in the Visualization module, click the Options menu dialog boxes.
Within each dialog box, the Visualization module highlights options that are on, displays the
names of selected colors, identifies current style choices, and so on. A detailed comparison
between the *SHOW command in ABAQUS/Post and the related functionality in the
Visualization module is given in ``Visualization module functionality corresponding to each
0-1246
ABAQUS/Post SET/SHOW parameter,'' Section C.3.
*SUPER PATH
This feature is not supported in the Visualization module.
*SURFACE SET
To access this functionality in the Visualization module, click Tools->Display Group.
Differences between *SURFACE SET in ABAQUS/Post and display groups in the
Visualization module are as follows:
· ABAQUS/Post surface sets can contain only surfaces; the Visualization module display
groups can contain any combination of elements, nodes, and surfaces.
· The Visualization module extends this feature to allow the creation of display groups
based on results.
· In ABAQUS/Post you can color surface sets using the *COLOR SET command. In the
Visualization module you can color selected surfaces using Tools->Color Code.
· ABAQUS/Post surface sets support only the add, remove, and delete operations. The
Visualization module display groups support numerous Boolean operations and can be
copied and renamed.
To learn more about display groups in the Visualization module, see Chapter 36, "Displaying a
subset of your model."
*SYSTEM
This feature is not supported in the Visualization module.
*TITLE
To access this functionality in the Visualization module, click Canvas->Create Text. In
addition to this functionality, the Visualization module offers cursor controlled text relocation,
annotation arrows in several line styles, editing of existing text annotations, and extensive font
customization options.
*VECTOR PLOT
To produce a symbol plot in the Visualization module, click Plot->Symbols. To access the
functionality of the ABAQUS/Post *VECTOR PLOT, MATERIAL DIRECTION feature, click
Plot->Material Orientation. Differences between *VECTOR PLOT in ABAQUS/Post and
symbol or material orientation plotting in the Visualization module are as follows:
· For vector plots of integration point quantities, ABAQUS/Post extrapolates, averages, and
then displays vectors and tensors at the nodes; the Visualization module displays
integration point quantities at the integration points.
0-1247
orientations are first extrapolated to the nodes, then averaged.
· In ABAQUS/Post you can specify only one section point from which to obtain results for
all shells, beams, and layered solids included in the plot. In the Visualization module you
can specify a separate section point for each category of beam and shell included in the
plot.
· The Visualization module displays material orientations for all shell and beam elements
and only those solid elements whose section definition contains a local material
orientation. ABAQUS/Post displays material orientations for all element types defined in
a model.
· In ABAQUS/Post you use the same options to customize both vectors and tensors. In the
Visualization module you can choose separate customization options for tensors and
vectors.
· In ABAQUS/Post you can specify a constant size for vector arrow tips, and you can
customize the maximum length of vector arrow shafts. In the Visualization module arrow
tips are always scaled, and shaft length options are limited to short, medium, and long.
· The Visualization module offers a more extensive set of customization options than
ABAQUS/Post for the appearance of the material orientation triad.
For more information, see Chapter 28, "Plotting analysis results as symbols," and Chapter 29,
"Plotting material orientations."
*VIEW
To access this functionality in the Visualization module, click View->Specify. To learn more
about view control, see ``Numerically specifying a view,'' Section 8.1.9.
In addition, the Visualization module facilitates view control with View->Views Toolbox ,
which provides quick access to up to 11 preset views, and with the and icons on the
toolbar.
*WINDOW
To access this functionality in the Visualization module, click the Canvas menu and choose
one of the Viewport options. Unlike ABAQUS/Post windows, viewports are always active
and can each maintain their own customization settings, output database file, and so on.
*ZOOM
To access this functionality in the Visualization module, click View->Specify. To learn more
about zooming a view, see ``Numerically specifying a view,'' Section 8.1.9.
In addition, the Visualization module facilitates zooming with the and icons on the
toolbar.
0-1248
C.3 Visualization module functionality corresponding to each
ABAQUS/Post SET/SHOW parameter
This section lists the ABAQUS/Post *SET and *SHOW command parameters alphabetically. Those
features not supported by the Visualization module are identified. For each supported feature, an
explanation is given of how the Visualization module functionality compares to ABAQUS/Post. For
information on ABAQUS/Post commands and parameters, see the ABAQUS/Post Manual.
AXA ANGLE
To access this functionality in the Visualization module, click View->ODB Display
Options->Sweep & Extrude . For more information, see ``Sweeping and extruding your
model,'' Section 37.9.1.
AXA SEGMENTS
To access this functionality in the Visualization module, click View->ODB Display
Options->Sweep & Extrude . For more information, see ``Sweeping and extruding your
model,'' Section 37.9.1.
AXES
To access this functionality in the Visualization module, click View->Viewport
Annotations->Triad. The Visualization module extends this functionality to include font and
axes labels customization. For more information, see ``Customizing the view triad,'' Section
8.2.
AXISYMMETRIC ANGLE
To access this functionality in the Visualization module, click View->ODB Display
Options->Sweep & Extrude . For more information, see ``Sweeping and extruding your
model,'' Section 37.9.1.
BACKGROUND COLOR
This functionality is not supported in the Visualization module.
BC DISPLAY
To access this functionality in the Visualization module, click View->ODB Display
Options->BC.
0-1249
information, see ``Displaying element and surface normals,'' Section 37.7.
BOND SIZE
This functionality is not supported in the Visualization module.
BORDER COLOR
This functionality is not supported in the Visualization module.
C AVERAGE
To access this functionality in the Visualization module, click Result->Field Output->Result
Options. The Visualization module extends this functionality to include additional averaging
options. For more information, see ``Controlling result averaging,'' Section 24.4.4.
C BORDER
To access this functionality in the Visualization module, click Options->Contour->Color
& Style->Banded. The Visualization module extends this functionality to include style and
thickness options. For more information, see ``Customizing banded-type contours,'' Section
27.4.3.
C BOX LEGEND
To access this functionality in the Visualization module, click View->Viewport
Annotations->Legend. For more information, see ``Customizing the legend,'' Section 38.1.
C DIGITS LEGEND
To access this functionality in the Visualization module, click View->Viewport
Annotations->Legend. For more information, see ``Customizing the legend,'' Section 38.1.
C LABELS
This functionality is not supported in the Visualization module.
C LEGEND
To access this functionality in the Visualization module, click View->Viewport
Annotations->Legend. For more information, see ``Customizing the legend,'' Section 38.1.
C LEVELS
To access this functionality in the Visualization module, click Options->Contour->Basic.
The Visualization module extends this functionality by offering Uniform or Continuous
contour intervals. For more information, see ``Customizing contour intervals,'' Section 27.4.9.
0-1250
C MAGNIFICATION
To access this functionality in the Visualization module, click Options->Contour->Shape.
For more information, see ``Scaling deformations,'' Section 37.5.2.
C MAXIMUM
To access this functionality in the Visualization module, click Options->Contour->Limits.
The Visualization module extends this functionality to include automatic computation options.
For more information, see ``Setting contour limits,'' Section 27.4.6.
C MINIMUM
To access this functionality in the Visualization module, click Options->Contour->Limits.
The Visualization module extends this functionality to include automatic computation options.
For more information, see ``Setting contour limits,'' Section 27.4.6.
C QUILT
To access this functionality in the Visualization module, click Options->Contour->Basic.
For more information, see ``Choosing line-, banded-, or quilt-type contours, '' Section 27.4.1.
C REPORT
To access this functionality in the Visualization module, click View->Viewport
Annotations->Legend. For more information, see ``Customizing the legend,'' Section 38.1.
C REVERSE
To access this functionality in the Visualization module, click Options->Contour->Color
& Style->Spectrum. For more information, see ``Customizing contour colors,'' Section 27.4.8.
C SCALE
You cannot directly scale contour values in the Visualization module; however, you can save
and then operate on results to create new user field output objects. For more information, see
``Creating new field output,'' Section 24.5.
C SECTION
This feature is not applicable to the Visualization module.
C SPECIAL
This feature is not applicable to the Visualization module.
C TICKMARKS
To access this functionality in the Visualization module, click Options->Contour->Basic.
0-1251
For more information, see ``Contouring line-shaped elements with tick mark contour plots, ''
Section 27.4.4.
C TITLE
To access this functionality in the Visualization module, click View->Viewport
Annotations->Title Block and View->Viewport Annotations->State Block. For more
information, see ``Customizing the title block,'' Section 38.2, and ``Customizing the state
block,'' Section 38.3.
CAPTURE
To save one or more currently playing animations to an animation file in the Visualization
module, click Animate->Save As. In the Visualization module, you cannot save an arbitrary
sequence of images to an animation file. For more information, see Chapter 34, "Animating
plots."
CENTER
In the Visualization module you cannot specify a set of model coordinates to appear in the
center of the viewport; however, you can rescale your display and center it within the viewport
using View->Auto-Fit or the icon on the toolbar. For more information, see
``Understanding the view manipulation tools, '' Section 8.1.
CLIP NORMAL
This functionality is not supported in the Visualization module.
CLIP POINT
This functionality is not supported in the Visualization module.
CLIPPING
This functionality is not supported in the Visualization module.
COLOR SET
You cannot show the current element and surface color definitions in the Visualization
module; however, you can apply colors to selected elements and surfaces using Tools->Color
Code. For more information, see ``Coloring individual elements and surfaces,'' Section 37.4.
COLOR TABLE
This functionality is not supported in the Visualization module.
0-1252
Contact surfaces are plotted by default in the Visualization module. For more information, see
Chapter 36, "Displaying a subset of your model."
CRACK 1 COLOR
This functionality is not supported in the Visualization module.
CRACK 2 COLOR
This functionality is not supported in the Visualization module.
CRACK 3 COLOR
This functionality is not supported in the Visualization module.
CRACK STYLE
This functionality is not supported in the Visualization module.
CRACK TITLE
This functionality is not supported in the Visualization module.
CURVE ATTRIBUTES
To access this functionality in the Visualization module, click Tools->XY Data->Manager,
which lists X-Y data objects by name and states the origin of the data. You cannot show the
number of members of an X-Y data object in the Visualization module, and you cannot display
detailed information about the attributes of the data. For more information, see ``Managing
objects using manager dialog boxes,'' Section 6.5.6.
CURVE DATA
In the Visualization module you can display the X-Y data pairs in an X-Y data object only by
editing the data; however, you can report these values to a file. For more information, see
Chapter 35, "Generating tabular data reports."
D COLOR
To access this functionality in the Visualization module, click Options->Deformed->Color
& Style. The Visualization module extends this functionality to offer both edge and fill color
customization. For more information, see ``Selecting overall element and surface edge color,''
Section 37.3.3, and ``Selecting overall fill color,'' Section 37.2.3.
D MAGNIFICATION
To access this functionality in the Visualization module, click Options->Deformed->Basic.
For more information, see ``Scaling deformations,'' Section 37.5.2.
D OFFSET
To access this functionality in the Visualization module, click
Options->Deformed->Other->Offset. For more information, see ``Superimposing deformed
and undeformed model plots,'' Section 26.4.
0-1253
D REPORT
To access this functionality in the Visualization module, click View->Viewport
Annotations->Legend. For more information, see ``Customizing the legend,'' Section 38.1.
D TITLE
To access this functionality in the Visualization module, click View->Viewport
Annotations->Title Block and View->Viewport Annotations->State Block.
For more information, see ``Customizing the title block,'' Section 38.2, and ``Customizing the
state block,'' Section 38.3.
D TRANSLUCENCY
To access this functionality in the Visualization module, click
Options->Deformed->Other->Translucency. For more information, see ``Customizing
lightsource-shaded translucency,'' Section 37.2.2.
DASHED
To access this functionality in the Visualization module, click Options->plot mode->Color
& Style. The Visualization module offers several dash styles. For more information, see
``Customizing element and surface edge style,'' Section 37.3.4.
DEPTH CYLINDER
To access this functionality in the Visualization module, click View->ODB Display
Options->Sweep & Extrude . For more information, see ``Sweeping and extruding your
model,'' Section 37.9.1.
DETAIL
You cannot list the contents of a display group in the Visualization module. For more
information, see Chapter 36, "Displaying a subset of your model."
DEVICE
This functionality is not supported in the Visualization module.
DIALOG BACKGROUND
This functionality is not supported in the Visualization module.
DIALOG COLOR
This functionality is not supported in the Visualization module.
ECHO
This functionality is not supported in the Visualization module.
EDGE TOLERANCE
This functionality is not supported in the Visualization module.
0-1254
EIGENMODE
To access this functionality in the Visualization module, click Result->Frame. For more
information, see ``Selecting a specific results step and frame,'' Section 24.2.1.
EL NUMBERS
To access this functionality in the Visualization module, click Options->plot mode->Labels.
The Visualization module extends this functionality to include label font customization. For
more information, see ``Customizing element labels,'' Section 37.6.2.
EL PLOT
This functionality is not supported in the Visualization module.
ELSET
To list all available element sets in the Visualization module, click Tools->Display Group.
This functionality is comparable to the ABAQUS/Post *SHOW, ELSET command. In the
Visualization module you cannot list the elements in an element set (as you can with the
ABAQUS/Post *SHOW, ELSET=name command); however, you can highlight an element set
in the viewport. For more information, see Chapter 36, "Displaying a subset of your model."
ERASE
This functionality is not supported in the Visualization module.
ERROR COLOR
This functionality is not supported in the Visualization module.
ERROR JOURNALING
This functionality is not supported in the Visualization module.
FACE IDENTIFICATION
To access this functionality in the Visualization module, click Options->plot mode->Labels.
The Visualization module extends this functionality to include label font customization. For
more information, see ``Customizing face labels,'' Section 37.6.3.
FILL
To access this functionality in the Visualization module, click Options->plot mode->Basic.
For more information, see ``Selecting overall fill color,'' Section 37.2.3.
FONT
This functionality is supported in the Visualization module by the Select Font dialog box,
which is accessible from all dialog boxes that support font customization. For more
information, see ``Customizing fonts,'' Section 6.3.6.
GLOBAL BACKGROUND
0-1255
This functionality is not supported in the Visualization module.
GRAPH AXES
To access this functionality in the Visualization module, click Options->XY Graph. For more
information, see ``Customizing X-Y plot axes,'' Section 30.5.
GRAPH LEGEND
To access this functionality in the Visualization module, click View->Viewport
Annotations->Legend. For more information, see ``Customizing the legend,'' Section 38.1.
GRAPH ORIGIN
The functionality is not supported in the Visualization module; however, you can position
GRAPH SIZE
To access this functionality in the Visualization module, click Options->XY Graph->Aspect
Ratio. For more information, see ``Adjusting the X-Y plot aspect ratio,'' Section 30.5.9.
HARD COPY
To access this functionality in the Visualization module, click File->Print. For more
information, see Chapter 11, "Printing canvas objects."
HIDE
To access this functionality in the Visualization module, click Options->plot mode->Basic.
For more information, see ``Choosing a render style,'' Section 37.2.1.
HISTORY
This command is not applicable to the Visualization module.
JOURNAL FILE
In the Visualization module you cannot control the name of the file to which session
commands are written.
LIGHT SOURCE
This functionality is not supported in the Visualization module.
LINE SEGMENTS
To access this functionality in the Visualization module, click View->ODB Display
Options->General. The Curved Lines & Faces options are at the top of the dialog box. For
more information, see ``Refining curved edges and faces,'' Section 37.9.2.
LOAD DISPLAY
0-1256
This functionality is not supported in the Visualization module.
LOGO
The ABAQUS logo does not appear in the Visualization module viewports; however, you can
control whether or not the logo appears in the Visualization module PostScript files. For more
information, see ``Customizing the image sent to a PostScript printer or file, '' Section 11.2.5.
MAXIMUM COLORS
This functionality is not supported in the Visualization module.
MB1
You cannot change the functions of the mouse buttons in the Visualization module.
MB2
You cannot change the functions of the mouse buttons in the Visualization module.
MB3
You cannot change the functions of the mouse buttons in the Visualization module.
MESSAGE BACKGROUND
This functionality is not supported in the Visualization module.
MESSAGE TEXT
This functionality is not supported in the Visualization module.
MODEL BOUNDS
This functionality is not supported in the Visualization module.
N NUMBERS
To access this functionality in the Visualization module, click Options->plot mode->Labels.
The Visualization module extends this functionality to include label font customization. For
more information, see ``Customizing node labels,'' Section 37.6.4.
NAME
This functionality is not supported in the Visualization module.
NODES
To access this functionality in the Visualization module, click Options->plot mode->Labels.
The Visualization module extends this functionality to include node symbol type options. For
more information, see ``Customizing node symbols,'' Section 37.6.5.
0-1257
NORMAL SMOOTHING
To access this functionality in the Visualization module, click View->ODB Display
Options->General. The Feature Angle options are at the bottom of the dialog box. For more
information, see ``Defining model feature edges,'' Section 37.3.2.
NSET
To list all available node sets in the Visualization module, click Tools->Display Group. This
functionality is comparable to the ABAQUS/Post *SHOW, NSET command. In the
Visualization module you cannot list the nodes in a node set (as you can with the
ABAQUS/Post *SHOW, NSET=name command); however, you can highlight a node set in
the viewport. For more information, see Chapter 36, "Displaying a subset of your model."
ORIGIN
This functionality is not supported in the Visualization module.
OUTLINE
To access this functionality in the Visualization module, click Options->plot mode->Basic.
The Visualization module extends this functionality by offering Exterior and Free edge
display. For more information, see ``Controlling element and surface edge visibility,'' Section
37.3.1.
OUTPUT FORMAT
To access this functionality in the Visualization module, click File->Print. Extended output
format options become available when you click File as the Destination. For more
information, see ``Printed image formats,'' Section 11.1.1.
PAN
In the Visualization module you can pan your display by clicking View->Pan or
View->Specify or by using the icon on the toolbar. For more information, see
``Understanding the view manipulation tools, '' Section 8.1.
REPORT FILE
To access this functionality in the Visualization module, click Report->XY->Setup,
Report->Field Output->Setup, or Tools->Query. For more information, see ``Specifying
0-1258
your report file name,'' Section 35.4, or ``Using the query toolset,'' Section 31.3.
RESCALE
This functionality is not supported in the Visualization module.
RESTART
The ABAQUS/Post *SHOW, RESTART command shows the name of the restart file and the
available restart numbers, times, steps, and increments. The Visualization module displays the
available output database steps and frames when you click Result->Frame. The name of the
current output database appears in the title of all model plots and in the context bar. To control
plot titles, click View->Viewport Annotations->Title Block.
For more information, see ``Selecting a specific results step and frame,'' Section 24.2.1, and
``Customizing the title block,'' Section 38.2.
RESULTS FILE
This functionality is not applicable to the Visualization module.
SCALING
To access this functionality in the Visualization module, click Options->plot
mode->Other->Scaling. For more information, see ``Scaling coordinates and shrinking the
model,'' Section 37.5.3.
SCREEN BOUNDS
This functionality is not supported in the Visualization module.
SEQUENCE FILE
This functionality is not supported in the Visualization module.
SHADE
To access this functionality in the Visualization module, click Options->plot mode->Basic.
For more information, see ``Choosing a render style,'' Section 37.2.1.
SHADING
This functionality is not supported in the Visualization module.
SHIFT CYLINDER
This functionality is not supported in the Visualization module.
0-1259
SHRINK
To access this functionality in the Visualization module, click Options->plot
mode->Other->Scaling. In ABAQUS/Post setting shrink to zero is equivalent to turning
shrink off. In the Visualization module you can enable shrink at a percentage of zero. This has
the effect of causing all element and surface edges to be visible, regardless of edge visibility
settings.
For more information, see ``Scaling coordinates and shrinking the model,'' Section 37.5.3.
SUPER PATH
This functionality is not supported in the Visualization module.
SUPERELEMENTS
This functionality is not supported in the Visualization module.
SURFACES
To list all available surfaces in the Visualization module, click Tools->Display Group. This
is comparable to the ABAQUS/Post *SHOW, SURFACES command. In the Visualization
module you cannot list the surfaces in a surface set (as you can with the ABAQUS/Post
*SHOW, SURFACE=name command); however, you can highlight a surface set in the
viewport. For more information, see Chapter 36, "Displaying a subset of your model."
SWEEP SEGMENTS
To access this functionality in the Visualization module, click View->ODB Display
Options->Sweep & Extrude . For more information, see ``Sweeping and extruding your
model,'' Section 37.9.1.
SYMBOL LENGTH
This functionality is not supported in the Visualization module.
TEXT SIZE
This functionality is supported in the Visualization module by the Select Font dialog box,
which is accessible from all dialog boxes that support font customization. For more
information, see ``Customizing fonts,'' Section 6.3.6.
TRUE SCALE
This functionality is not supported in the Visualization module.
TWIST
This functionality is not supported in the Visualization module.
U COLOR
0-1260
To access this functionality in the Visualization module, click Options->Undeformed->Color
& Style. Unlike ABAQUS/Post, the color you specify applies to undeformed model display
with or without the deformed shape. The Visualization module extends this functionality to
offer both edge and fill color customization.
For more information, see ``Selecting overall element and surface edge color,'' Section 37.3.3,
and ``Selecting overall fill color,'' Section 37.2.3.
U TRANSLUCENCY
To access this functionality in the Visualization module, click
Options->Undeformed->Other->Translucency. For more information, see ``Customizing
lightsource-shaded translucency,'' Section 37.2.2.
UNDEFORMED
To access this functionality in the Visualization module, click Options->Deformed->Basic.
For more information, see ``Superimposing deformed and undeformed model plots,'' Section
26.4.
V 1 COLOR
To access this functionality in the Visualization module, click Options->Symbol->Color
& Style->Vector or Options->Symbol->Color & Style->Tensor. For more information, see
``Customizing symbol plot arrows,'' Section 28.4.2.
V 2 COLOR
To access this functionality in the Visualization module, click Options->Symbol->Color
& Style->Vector or Options->Symbol->Color & Style->Tensor. For more information, see
``Customizing symbol plot arrows,'' Section 28.4.2.
V 3 COLOR
To access this functionality in the Visualization module, click Options->Symbol->Color
& Style->Vector or Options->Symbol->Color & Style->Tensor. For more information, see
``Customizing symbol plot arrows,'' Section 28.4.2.
To customize the color of arrows representing element and surface normals, click
Options->Undeformed->Normals or Options->Deformed->Normals. For more
information, see ``Displaying element and surface normals,'' Section 37.7.
V LENGTH
To access this functionality in the Visualization module, click Options->Symbol->Color
& Style->Vector or Options->Symbol->Color & Style->Tensor; choices are limited to short,
medium, and long. For more information, see ``Customizing symbol plot arrows,'' Section
28.4.2.
V REPORT
0-1261
To access this functionality in the Visualization module, click View->Viewport
Annotations->Legend. For more information, see ``Customizing the legend,'' Section 38.1.
V TIP SCALE
This functionality is not supported in the Visualization module.
V TIP STYLE
To access this functionality in the Visualization module, click Options->Symbol->Color
& Style->Vector or Options->Symbol->Color & Style->Tensor. For more information, see
``Customizing symbol plot arrows,'' Section 28.4.2.
VIEW
To show the current view in the Visualization module, click Options->View->Specify. For
more information, see ``Numerically specifying a view,'' Section 8.1.9.
WINDOW BOUNDS
This functionality is not supported in the Visualization module.
WINDOW LIST
This functionality is not supported in the Visualization module.
X BUFFER
To access buffering and other graphics options in the Visualization module, click View->View
Options->Hardware . For more information, see Chapter 10, "Tuning display performance."
XY HIGHLIGHT COLOR
This functionality is not supported in the Visualization module.
XY PRINT FILE
To access this functionality in the Visualization module, click Report->XY->Setup. For more
information, see ``Specifying your report file name,'' Section 35.4.
XY REPORT
To access this functionality in the Visualization module, click View->Viewport
Annotations->Legend. For more information, see ``Customizing the legend,'' Section 38.1.
ZOOM
To access this functionality in the Visualization module, click View->Specify. For more
information, see ``Applying a specified view,'' Section 8.4.9.
0-1262
Glossary
This section contains short definitions of terms that appear throughout the ABAQUS/CAE
documentation. Following each definition are cross references to relevant sections throughout the
documentation. To see glossary definitions beginning with a particular letter of the alphabet, click that
letter in the table below.
A B C D E F G H I J K L M
N O P Q R S T U V W X Y Z
When you are viewing the online documentation and move the cursor over a term that appears in the
glossary, the cursor changes to a pointing hand. If you click mouse button 1, a separate window is
displayed that contains the description of the term from the glossary and cross references to associated
material. To close this glossary window, select File->Close View from its menu bar.
A
ABAQUS/Aqua
ABAQUS/Aqua is an add-on analysis capability for ABAQUS/Standard that provides wave
loading, drag, and buoyancy calculation capabilities for modeling offshore piping and floating
platform structures.
· ``Parametric input,'' Section 1.4.1 of the ABAQUS/Standard User's Manual and the
ABAQUS/Explicit User's Manual
ABAQUS/Explicit
ABAQUS/Explicit is a batch input, finite element program that provides nonlinear, transient,
0-1263
dynamic analysis of solids and structures using explicit time integration. Its powerful contact
capabilities, reliability, and computational efficiency on large models also make it highly
effective for quasi-static applications involving discontinuous nonlinear behavior.
0-1264
ACIS-compatible files
ACIS is an industry-standard library of geometric modeling functions that reads and writes ACIS
(file extension .sat) format files. ACIS files give you a way to move geometry between
ABAQUS/CAE and third-party modeling products. You can import the base feature of a part
from an ACIS file; in addition, you can export a part or the part instances in the assembly to an
ACIS file.
0-1265
assembly
An ABAQUS/CAE assembly is composed of part instances that you orient relative to each other
in the global coordinate system. Loads, boundary conditions, and interactions are applied to the
assembly, and the finite element mesh is generated on the assembly. The model contains only
one assembly.
0-1266
Edit, Copy, Rename, and Delete buttons that you can use to manipulate existing objects and to
create new ones. See also step-dependent manager.
0-1267
consists of a table of contents panel, which displays the table of contents of the book, and a
content panel, which displays the material for you to read.
· ``Boundary conditions,'' Section 19.3.1 of the ABAQUS/Standard User's Manual and Section
18.3.1 of the ABAQUS/Explicit User's Manual
C
canvas
The canvas is the region of the ABAQUS/CAE main window where work takes place. The
canvas can be thought of as an infinite screen or bulletin board on which you post objects such
as viewports and annotations. You can imagine the canvas extending beyond the main window
and your monitor; the visible portion of the canvas is called the drawing area, which you can
increase by increasing the size of the main window.
0-1268
When you import a part from an IGES file, ABAQUS/CAE can check the part for precision
errors that require healing.
0-1269
context-sensitive help
Context-sensitive help allows you to gain immediate access to specific information in the
ABAQUS/CAE or ABAQUS/Viewer online manual. You invoke context-sensitive help by
selecting Help->On Context from the main menu bar and then clicking almost any feature of an
ABAQUS/CAE window or dialog box. The help consists of a short description of how to use the
feature, shown in a separate window.
0-1270
For more information:
· ``Input syntax rules,'' Section 1.2.1 of the ABAQUS/Standard User's Manual and the
ABAQUS/Explicit User's Manual
datum
A datum is a feature that represents auxiliary geometry which can be used for reference when
modeling a part or assembly. The following types of datum are available: points, axes, planes
and coordinate systems.
0-1271
· ``Part types,'' Section 14.4.2
deformation scale factor
The deformation scale factor is the factor that is applied to the deformation field when you
display a plot of a deformed model in ABAQUS/CAE. You can scale the deformations to
magnify, reduce, or otherwise distort the deformed model shape.
0-1272
For more information:
0-1273
In ABAQUS/CAE an edge parameter represents a position along an edge, expressed as a fraction
of its length. You can use an edge parameter to partition an edge and to position a datum along
an edge. ABAQUS/CAE displays an arrow along the edge indicating the direction of increasing
parameter value from the start vertex (corresponding to an edge parameter value of zero) to the
end vertex (corresponding to a value of one).
· ``Element definition,'' Section 2.2.1 of the ABAQUS/Standard User's Manual and the
ABAQUS/Explicit User's Manual
EPS (Encapsulated PostScript)
ABAQUS/CAE allows you to save images of selected canvas objects (viewports, text, and arrow
annotations) in EPS-format files. EPS is a variation of PostScript that describes a single graphic
designed to be included in a larger document without modification. EPS files are identical to
PostScript files except for some information that describes the size and positioning of the image.
Most word processing and graphics applications support the inclusion of EPS files.
0-1274
For more information:
· ``Using the face angle method to create a surface from an orphan mesh,'' Section 9.2.3
fast plot
Immediately upon opening an output database, the ABAQUS/CAE Visualization module
displays the model in the fast plot mode. A fast plot is a quickly drawn representation of the
model that does not display results and cannot be customized.
0-1275
fillet
A fillet is a circular arc that joins two lines in a continous manner. Fillets of a specified radius
are used in both sketches and parts in ABAQUS/CAE. When you are using the Sketch module,
you can create a fillet between two lines meeting at an angle. When you are creating or
modifying a three-dimensional solid part, you can fillet, or round, selected edges.
0-1276
For more information:
· ``Linear and nonlinear procedures,'' Section 6.1.2 of the ABAQUS/Standard User's Manual
geometry set
An ABAQUS/CAE geometry set is composed of geometric objects (cells, faces, edges, and
vertices) that you have selected from an unmeshed part or assembly. The geometric objects in a
set can be of different types; for example, you can include a face and an edge in the same set.
0-1277
precision errors.
· ``Defining a model in ABAQUS,'' Section 1.3.1 of the ABAQUS/Standard User's Manual and
the ABAQUS/Explicit User's Manual
history output
History output is the output of variables that are written relatively frequently to the output
database--as often as every increment. You typically select history output for a small area of
your model, such as a single integration point or a small region. You can use history output in
the ABAQUS/CAE Visualization module to generate X-Y plots.
· ``Using the *SHELL SECTION option to define the section behavior, '' Section 15.6.5 of the
ABAQUS/Standard User's Manual and Section 14.4.4 of the ABAQUS/Explicit User's
Manual
· ``Using the *SHELL GENERAL SECTION option to define the section behavior, '' Section
15.6.6 of the ABAQUS/Standard User's Manual and Section 14.4.5 of the ABAQUS/Explicit
User's Manual
· ``Solid (continuum) elements,'' Section 14.1.1 of the ABAQUS/Standard User's Manual and
0-1278
Section 13.1.1 of the ABAQUS/Explicit User's Manual
hyperlink
Hyperlinks are electronic links between sections in the online documentation. You can use
hyperlinks to display material that is related to the material that you are currently reading. Some
hyperlinks already exist in the documentation, but you can also create your own.
· ``Initial conditions,'' Section 19.2.1 of the ABAQUS/Standard User's Manual and Section
18.2.1 of the ABAQUS/Explicit User's Manual
input file
An input file is an ASCII file that is read and processed by ABAQUS/Standard or
ABAQUS/Explicit. It contains keywords and data that define your model. When you submit a
job for analysis using ABAQUS/CAE, it generates an input file based on the model you have
defined. If necessary, you can modify the input file generated by ABAQUS/CAE using the
Keywords Editor. In addition, you can import input files into ABAQUS/CAE; ABAQUS/CAE
translates the options and data lines in the imported input file into a new ABAQUS/CAE model.
· ``Understanding the files generated by creating and analyzing a model,'' Section 12.3
· ``Importing models from ABAQUS/Standard and ABAQUS/Explicit input files,'' Section 13.4
0-1279
· ``Defining a model in ABAQUS,'' Section 1.3.1 of the ABAQUS/Standard User's Manual and
the ABAQUS/Explicit User's Manual
input parameter
The parametric input capability in ABAQUS/Design allows the user to create an input file in
which parameters are used in place of input quantities. The parameters are evaluated according
to their definition and are substituted for the parametrized quantities before an analysis is
performed by ABAQUS/Standard or ABAQUS/Explicit. See also keyword parameter to learn
how keyword parameters are used in an ABAQUS input file.
· ``Scripting parametric studies,'' Section 25.1.1 of the ABAQUS/Standard User's Manual and
Section 23.1.1 of the ABAQUS/Explicit User's Manual
instance
See part instance.
interaction
ABAQUS is capable of modeling mechanical, thermal, coupled thermal-mechanical, coupled
pore fluid-mechanical, and coupled thermal-electrical interactions between bodies. In
ABAQUS/CAE an elastic foundation is also considered a form of interaction.
0-1280
· Chapter 21, "The Job module"
· ``An introduction to using ABAQUS,'' Section 1.1.2 of the ABAQUS/Standard User's Manual
· ``An introduction to using ABAQUS,'' Section 1.1.2 of the ABAQUS/Standard User's Manual
0-1281
· ``An introduction to using ABAQUS/Explicit,'' Section 1.1.2 of the ABAQUS/Explicit User's
Manual
keyword parameter
Keywords in an ABAQUS input file are often followed by parameters on the keyword line of an
option block. Keyword parameters, which can be optional or required, provide additional
information concerning the keyword. For example, the keyword *ELEMENT requires the
keyword parameter TYPE to specify what type of element (such as solid, beam, or shell) is being
defined. See also input parameter to learn how input parameters are used in ABAQUS/Design.
keywords editor
The keywords editor is a specialized text editor that allows you to modify the ABAQUS input
file generated by ABAQUS/CAE before submitting it for analysis.
· ``Applying loads: overview,'' Section 19.4.1 of the ABAQUS/Standard User's Manual and
Section 18.4.1 of the ABAQUS/Explicit User's Manual
Load/BC/IC module
The ABAQUS/CAE Load/BC/IC module allows you to define prescribed conditions such as
loads, boundary conditions, and initial conditions.
0-1282
menu bar and the toolbar, can change as you work through the modeling process.
· ``Element definition,'' Section 2.2.1 of the ABAQUS/Standard User's Manual and the
ABAQUS/Explicit User's Manual
Mesh module
The ABAQUS/CAE Mesh module contains tools that allow you to generate meshes on
assemblies created in ABAQUS/CAE. In addition, the Mesh module contains query functions
that provide information about existing meshes.
0-1283
· Chapter 20, "The Mesh module"
mesh surface
You can use the ABAQUS/CAE Surface toolset to create a mesh surface by selecting element
faces or edges from orphan meshes in an assembly.
· ``Understanding the files generated by creating and analyzing a model,'' Section 12.3
· ``Output,'' Section 4.1.1 of the ABAQUS/Standard User's Manual and the ABAQUS/Explicit
User's Manual
model
A finished model contains all the data that are needed to conduct an analysis. The term model
also refers just to the physical object being analyzed.
· ``Defining a model in ABAQUS,'' Section 1.3.1 of the ABAQUS/Standard User's Manual and
the ABAQUS/Explicit User's Manual
model definition
The model definition is the internal ABAQUS representation of the model.
· ``Defining a model in ABAQUS,'' Section 1.3.1 of the ABAQUS/Standard User's Manual and
the ABAQUS/Explicit User's Manual
model data
0-1284
The term model data refers to the portion of an ABAQUS/Standard or ABAQUS/Explicit input
file that defines a finite element model: the elements, nodes, element properties, material
definitions, and so on--any data that specify the model itself. Model data include all data in an
ABAQUS input file that appear before the *STEP keyword.
· ``Defining a model in ABAQUS,'' Section 1.3.1 of the ABAQUS/Standard User's Manual and
the ABAQUS/Explicit User's Manual
model database
ABAQUS/CAE uses model databases to store your models and analysis jobs. While you may
have multiple model databases stored on your computer or network, ABAQUS/CAE can work
on only one at any time. The model database in use is known as the current model database, and
ABAQUS/CAE displays its name across the top of the main window.
· ``Output,'' Section 4.1.1 of the ABAQUS/Standard User's Manual and the ABAQUS/Explicit
User's Manual
movable part instance
The movable part instance is the part instance whose position can change during the application
of an assembly constraint in ABAQUS/CAE.
0-1285
For more information:
· ``Node definition,'' Section 2.1.1 of the ABAQUS/Standard User's Manual and the
ABAQUS/Explicit User's Manual
note
Notes are annotations that you can add to the online documentation. Creating a note in an online
manual is like writing a note in the margin of a printed book for future reference. Notes that you
create are saved from one session to the next.
0-1286
For more information:
· ``An introduction to using ABAQUS,'' Section 1.1.2 of the ABAQUS/Standard User's Manual
· ``An introduction to using ABAQUS,'' Section 1.1.2 of the ABAQUS/Standard User's Manual
· ``Imported parts from ACIS-, IGES-, and VDA-FS-format files,'' Section 14.5.2
output database
Output database files ( job_name.odb) contain the results from your analysis. You use the
Visualization module to open an output database and to view a graphical representation of the
contents. In addition, you can import a part from an output database in the form of an orphan
mesh.
0-1287
output request
You create output requests to instruct ABAQUS to write data of interest to various output files,
such as the data file ( .dat), the output database ( .odb), and the restart file ( .res). The
variables that ABAQUS writes during a step, the rate at which they are written, the region of the
model associated with the output, and the section points of interest define an output request.
· ``Output,'' Section 4.1.1 of the ABAQUS/Standard User's Manual and the ABAQUS/Explicit
User's Manual
P
parameter
In general, a parameter is a variable quantity that restricts or gives particular form to the thing
that it characterizes. This term is used in ABAQUS/CAE to refer to modifiable parameters that
define features (for example, the length of an extrusion). It is also used in the term ``edge
parameter'' to describe a position along an edge, expressed as a fraction of its length. See also
keyword parameter to learn how parameters are used in ABAQUS/Standard and
ABAQUS/Explicit, and see input parameter to learn how they are used in ABAQUS/Design.
· ``An introduction to using ABAQUS,'' Section 1.1.2 of the ABAQUS/Standard User's Manual
0-1288
An ABAQUS/CAE part set is a set consisting of a region of a part. Part sets are available only
when you are in the Part or Property modules.
0-1289
inertia properties as the rigid body. You can specify these properties by defining a point section
with inertial properties and then applying the section to the rigid body's reference point. The
section definition can also include optional damping data.
0-1290
that were detected while processing the input data. In addition, the printed output file contains
any printed output data written during the analysis.
· ``Output,'' Section 4.1.1 of the ABAQUS/Standard User's Manual and the ABAQUS/Explicit
User's Manual
probe
When you select Tools->Query from the main menu bar or use the tool in the toolbar,
ABAQUS/CAE enters probe mode, as indicated in the prompt area. In this mode
ABAQUS/CAE displays information as you move the cursor around the current viewport.
Probing a model plot displays model data and analysis results; probing an X-Y plot displays X-Y
curve data. You can write this information to a file.
· ``Procedures: overview,'' Section 6.1.1 of the ABAQUS/Standard User's Manual and the
ABAQUS/Explicit User's Manual
profile
When you create a beam section, you must also create a generalized profile (area, moments of
inertia, and torsional rigidity) that will be referred to by the section. If the beam section is open,
its profile definition must also include the sectoral moment and warping constant.
0-1291
message area. The prompt area displays instructions for you to follow during a procedure.
0-1292
background or submitting the job to a named batch queue on a host machine.
· ``Defining an initial temperature gradient through a shell section, '' Section 19.7.17
· ``Defining the shell element's initial geometry,'' Section 15.6.3 of the ABAQUS/Standard
User's Manual
0-1293
regenerate
The process of regeneration recalculates model geometry after a feature of an ABAQUS/CAE
model has been modified; by default, ABAQUS/CAE automatically regenerates all dependent
features if you modify a feature. For example, if you modify a feature of a part, ABAQUS/CAE
regenerates the part, any instances of the part in the assembly, and the final mesh.
· ``Restarting an analysis,'' Section 7.1.1 of the ABAQUS/Standard User's Manual and the
ABAQUS/Explicit User's Manual
resource file
The ABAQUS resource file allows you to control certain aspects of the appearance and behavior
of ABAQUS/CAE such as the size and style of fonts, the color of dialog boxes, or which files
are displayed by default in the Open Database dialog box.
0-1294
For more information:
· ``Defining the axis of revolution for axisymmetric parts and for revolved features, '' Section
14.9.2
rigid body
In general, rigid body is one that is so much stiffer than the rest of the model that its deformation
can be considered negligible. In ABAQUS/Standard and ABAQUS/Explicit, a rigid body is a
collection of rigid elements. See also analytical rigid part or discrete rigid part for information
about rigid bodies in ABAQUS/CAE.
· ``Defining analytical rigid surfaces,'' Section 2.3.4 of the ABAQUS/Standard User's Manual
and the ABAQUS/Explicit User's Manual
rigid body reference point or node
The rigid body reference point is a selected point that is used to define the motion of a rigid body
(a rigid part in ABAQUS/CAE) or to apply constraints to a rigid body. The rigid body reference
node is the node located at the rigid body reference point. When constraining the rigid body, you
apply constraints to the degrees of freedom of the rigid body reference node.
· ``Defining analytical rigid surfaces,'' Section 2.3.4 of the ABAQUS/Standard User's Manual
and the ABAQUS/Explicit User's Manual
round
You can use the blend tools in the Part module to round selected edges of the part in the current
viewport to the desired radius. A chamfer creates a straight blend; a round creates a rounded
0-1295
blend.
· ``Understanding the files generated by creating and analyzing a model,'' Section 12.3
search filter
You can use search filters to search for particular types of ABAQUS terms in the online
documentation.
0-1296
For more information:
· ``Using the *SHELL SECTION option to define the section behavior, '' Section 15.6.5 of the
ABAQUS/Standard User's Manual and Section 14.4.4 of the ABAQUS/Explicit User's
Manual
· ``Using the *BEAM SECTION option to define the section behavior, '' Section 15.3.6 of the
ABAQUS/Standard User's Manual and Section 14.3.6 of the ABAQUS/Explicit User's
Manual
section points
When you define shell or beam sections that are integrated during an analysis, you must specify
the number of section integration points through the thickness of the section. A group of section
points is located at each material integration point over the surface of a shell element or along
the length of a beam element.
· ``Using the *SHELL SECTION option to define the section behavior, '' Section 15.6.5 of the
ABAQUS/Standard User's Manual and Section 14.4.4 of the ABAQUS/Explicit User's
Manual
· ``Using the *BEAM SECTION option to define the section behavior, '' Section 15.3.6 of the
ABAQUS/Standard User's Manual and Section 14.3.6 of the ABAQUS/Explicit User's
Manual
seed
In ABAQUS/CAE, seeds are markers that you place along the edges of an unmeshed assembly to
indicate the desired density of the mesh. By default, mesh seeds provide only a target mesh
density; if necessary, the mesh generator alters the original seed distribution to successfully
generate the mesh. You can prevent this redistribution by constraining seeds.
0-1297
You select an ABAQUS/CAE viewport by clicking its border; a selected viewport is indicated
by handles around its border. You can have more than one selected viewport at a time.
ABAQUS/CAE applies Canvas menu operations, such as Delete and Make Viewport Current ,
to selected viewports. See also current viewport.
· ``An introduction to using ABAQUS,'' Section 1.1.2 of the ABAQUS/Standard User's Manual
0-1298
three-dimensional feature.
0-1299
For more information:
· ``Defining a model in ABAQUS,'' Section 1.3.1 of the ABAQUS/Standard User's Manual and
the ABAQUS/Explicit User's Manual
spline
A spline is a curve defined by a mathematical function that connects separate points with a high
degree of smoothness. Use the spline tool in the ABAQUS/CAE Sketch module to sketch a
smooth curve that connects a series of points. ABAQUS/CAE calculates the shape of the curve
using a cubic spline fit between all the points along the spline; as a result, the first and second
derivatives of the spline are continuous.
· ``Output,'' Section 4.1.1 of the ABAQUS/Standard User's Manual and the ABAQUS/Explicit
User's Manual
step
Within a model you define a sequence of one or more analysis steps. The step sequence provides
a convenient way to capture changes in the loading and boundary conditions of the model,
changes in the way parts of the model interact with each other, and any other changes that may
occur in the model during the course of the analysis. In addition, steps allow you to change the
analysis procedure, the data output, and various controls. You can also use steps to define linear
perturbation analyses about nonlinear base states.
· ``Defining a model in ABAQUS,'' Section 1.3.1 of the ABAQUS/Standard User's Manual and
the ABAQUS/Explicit User's Manual
step-dependent manager
Step-dependent managers in ABAQUS/CAE contain a list of all of the objects of a certain type
0-1300
that you have created. They are similar to basic managers in that they contain Create, Edit,
Copy, Rename, and Delete buttons that you can use to manipulate existing objects and to create
new ones. However, unlike basic managers, step-dependent managers contain additional
information concerning the history of each object listed in the manager. They also provide
buttons that you can use, in some cases, to manipulate the history of each object.
0-1301
· Chapter 45, "The Set and Surface toolsets"
· ``Surfaces: overview,'' Section 2.3.1 of the ABAQUS/Standard User's Manual and the
ABAQUS/Explicit User's Manual
Surface toolset
The Surface toolset is a collection of tools that allows you to create and manage surfaces.
· ABAQUS/CAE creates a mesh on one side of the region, known as the source side.
· ABAQUS/CAE copies the nodes of that mesh, one element layer at a time, until the final
side, known as the target side, is reached.
0-1302
For more information:
· ``Browsing and customizing the book window'' in Using ABAQUS Online Documentation
text field
Text fields are areas in ABAQUS/CAE dialog boxes in which you can enter information. For
example, when you create a material, you must enter the name of the material in the Name text
field in the Create Material dialog box.
0-1303
functions. The tools available in a toolbox are also available from the main menu bar.
· Chapter 23, "User Subroutines," of the ABAQUS/Standard User's Manual and Chapter 21 of
the ABAQUS/Explicit User's Manual
V
view
The position, orientation, and scale factor define the view of an object in an ABAQUS/CAE
0-1304
viewport.
0-1305
UNIX. It provides a standard and portable way of displaying graphics. You can choose between
two graphics drivers to operate your ABAQUS/CAE display: X11 and OpenGL
X-Y data object
An X-Y data object is a two-dimensional array that ABAQUS/CAE stores in two columns: an
X-column and a Y-column. You can use the Visualization module to display X-Y data in the form
of an X-Y plot.
· ``What is an X-Y data object, and what is an X-Y plot?,'' Section 30.1.1
X-Y plot
An X-Y plot is a two-axis graph of one variable versus another. ABAQUS/CAE can display X-Y
data objects in the form of an X-Y plot.
0-1306