Professional Documents
Culture Documents
Technical specifications: Inverted Cuvettes: The sample and the zero cuvette are inverted.
w w w. h a n n a i n s t . c o m
Weight 64 g (2.25 oz.)
Measurement procedure: Tips for an accurate measurement Accessories:
• Turn the meter on by pressing the button. • It is important that the sample does not contain any debris. REAGENT SETS
All segments will be displayed. When the • Whenever the cuvette is placed into the measurement cell, it must be dry HI 771-25 Reagent set for 25 Chlorine Ultra High Range tests
display shows “Add”, “C.1” with “Press” outside, and completely free of fingerprints, oil and dirt. Wipe it thoroughly with OTHER ACCESSORIES
blinking, the meter is ready. HI 731318 or a lint-free cloth prior to insertion. HI 771-11 Chlorine UHR Certified Standard Kit
• Shaking the cuvette can generate bubbles, causing higher readings. To obtain HI 731318 Cloth for wiping cuvettes (4 pcs.)
accurate measurements, remove bubbles by swirling or by gently tapping the HI 731321 Glass cuvettes (4 pcs.)
cuvette. HI 731225 Cuvette black cap for checker HC (4 pcs.)
• Fill the cuvette with 10 mL of unreacted
• Do not let the reacted sample stand for too long after reagent is added, as HI 731353 Cuvette seal cap for checker HC (4 pcs.)
sample and replace the cap. Place the cuvette 10 mL accuracy will be affected. HI 740028 1.5V AAA batteries (4 pcs.)
into the meter and close the meter’s cap.
• After the reading it is important to immediately discard the sample, otherwise HI 93703-50 Cuvette cleaning solution (230 mL)
the glass might become permanently stained.
Recommendations for Users
• Press the button. When the display shows Battery management Before using this product, make sure that it is entirely suitable for your specific application and for the
“Add”, “C.2” with “Press” blinking the environment in which it is used.
To save the battery, the instrument shuts down after 10 minutes of non-use. Operation of this instrument may cause unacceptable interferences to other electronic equipment, thus
meter is zeroed. One fresh battery lasts for a minimum of 5000 measurements. When the battery is dead requiring the operator to take all necessary steps to correct interferences.
the instrument will display “bAd” then ”bAt” for 1 second and then turns off. Any variation introduced by the user to the supplied equipment may degrade the instrument’s EMC
performance.
To restart the instrument, the battery must be replaced with a new one.
• Remove the cuvette from the meter and To avoid damage or burns, do not put the instrument in microwave oven. For the safety of you and the
To replace the instrument’s battery: instrument do not use or store the instrument in hazardous environments.
unscrew the cap. Add the content of one • Turn the instrument off by holding the button until the meter shuts off.
packet of HI 771A-0 reagent and one packet
• Turn the instrument upside down and remove the battery cover with a screwdriver. Hanna Instruments reserves the right to modify the design, construction or
of HI 771B-0 reagent.
• Replace the cap and shake gently for 20 seconds. appearance of its products without advance notice.
Place the cuvette back into the meter.
For additional information, contact your
• Press and hold the button until the timer is dealer or the nearest
displayed on the LCD (the display will show Hanna Customer Service Center.
the countdown prior to the measurement) To find a Hanna Office in your area,
visit our web site:
or, alternatively, wait for 1 minute and press
the button.
www.hannainst.com
• The instrument displays concentration in ppm
of chlorine. The meter automatically turns
• Remove the battery from its location and replace it with a new one, inserting the
IST771 04/13
off after 10 minutes.
negative end first.
• Insert the battery cover and replace the screw with a screwdriver.