Professional Documents
Culture Documents
Cli Commands VSP
Cli Commands VSP
-------------------------------------Checks-------------------------------------
Control Station: Checking statistics groups database....................... Pass
Control Station: Checking if file system usage is under limit.............. Pass
Control Station: Checking if NAS Storage API is installed correctly........ Pass
Control Station: Checking if NAS Storage APIs match........................ Pass
Control Station: Checking if NBS clients are started....................... Pass
Control Station: Checking if NBS configuration exists...................... Pass
Control Station: Checking if NBS devices are accessible.................... Pass
Control Station: Checking if NBS service is started........................ Pass
Control Station: Checking if PXE service is stopped........................ Pass
Control Station: Checking if standby is up................................. Pass
Control Station: Checking integrity of NASDB............................... Pass
Control Station: Checking if primary is active............................. Pass
Control Station: Checking all callhome files delivered..................... Pass
Control Station: Checking resolv conf...................................... Pass
Control Station: Checking if NAS partitions are mounted.................... Pass
Control Station: Checking ipmi connection.................................. Pass
Control Station: Checking nas site eventlog configuration.................. Pass
Control Station: Checking nas sys mcd configuration........................ Pass
Control Station: Checking nas sys eventlog configuration................... Pass
Control Station: Checking logical volume status............................ Pass
Control Station: Checking valid nasdb backup files......................... Pass
Control Station: Checking root disk reserved region........................ Pass
Control Station: Checking if RDF configuration is valid.................... N/A
Control Station: Checking if fstab contains duplicate entries.............. Pass
Control Station: Checking if sufficient swap memory available.............. Pass
Control Station: Checking for IP and subnet configuration.................. Pass
Control Station: Checking auto transfer status............................. Warn
Control Station: Checking for invalid entries in etc hosts................. Pass
Control Station: Checking for correct filesystem mount options............. Fail
Control Station: Checking the hard drive in the control station............ Pass
Control Station: Checking if Symapi data is present........................ Pass
Control Station: Checking if Symapi is synced with Storage System.......... Pass
Blades : Checking boot files....................................... Pass
Blades : Checking if primary is active............................. Fail
Blades : Checking if root filesystem is too large.................. ?
Blades : Checking if root filesystem has enough free space......... ?
Blades : Checking Server IfConfig.................................. Pass
Blades : Checking network connectivity............................. Pass
Blades : Checking status........................................... Pass
Blades : Checking dart release compatibility....................... Pass
Blades : Checking dart version compatibility....................... Pass
Blades : Checking server name...................................... Pass
Blades : Checking unique id........................................ Pass
Blades : Checking CIFS file server configuration................... Warn
Blades : Checking domain controller connectivity and configuration. Pass
Blades : Checking DNS connectivity and configuration............... Pass
Blades : Checking connectivity to WINS servers..................... Pass
Blades : Checking I18N mode and unicode translation tables......... Pass
Blades : Checking connectivity to NTP servers...................... Warn
Blades : Checking connectivity to NIS servers...................... Pass
Blades : Checking virus checker server configuration............... Pass
Blades : Checking if workpart is OK................................ Pass
Blades : Checking if free full dump is available................... Pass
Blades : Checking if each primary Blade has standby................ Info
Blades : Checking if Blade parameters use EMC default values....... Pass
Blades : Checking VDM root filesystem space usage.................. N/A
Blades : Checking if file system usage is under limit.............. Warn
Blades : Checking slic signature................................... Pass
Storage System : Checking disk emulation type.............................. Pass
Storage System : Checking disk high availability access.................... Pass
Storage System : Checking disks read cache enabled......................... Pass
Storage System : Checking disks and storage processors write cache enabled. Pass
Storage System : Checking if FLARE is committed............................ Pass
Storage System : Checking if FLARE is supported............................ Pass
Storage System : Checking array model...................................... Pass
Storage System : Checking if microcode is supported........................ N/A
Storage System : Checking no disks or storage processors are failed over... Pass
Storage System : Checking that no disks or storage processors are faulted.. Pass
Storage System : Checking that no hot spares are in use.................... Pass
Storage System : Checking that no hot spares are rebuilding................ Pass
Storage System : Checking minimum control lun size......................... Pass
Storage System : Checking maximum control lun size......................... N/A
Storage System : Checking maximum lun address limit........................ Pass
Storage System : Checking system lun configuration......................... Pass
Storage System : Checking if storage processors are read cache enabled..... Pass
Storage System : Checking if auto assign are disabled for all luns......... N/A
Storage System : Checking if auto trespass are disabled for all luns....... N/A
Storage System : Checking storage processor connectivity................... Pass
Storage System : Checking control lun ownership............................ N/A
Storage System : Checking if Fibre Channel zone checker is set up.......... N/A
Storage System : Checking if Fibre Channel zoning is OK.................... N/A
Storage System : Checking if proxy arp is setup............................ Pass
Storage System : Checking if Product Serial Number is Correct.............. Pass
Storage System : Checking SPA SPB communication............................ Pass
Storage System : Checking if secure communications is enabled.............. Pass
Storage System : Checking if backend has mixed disk types.................. Pass
Storage System : Checking for file and block enabler....................... Pass
Storage System : Checking if nas storage command generates discrepancies... Pass
Storage System : Checking if Repset and CG configuration are consistent.... Pass
Storage System : Checking block operating environment...................... Pass
Storage System : Checking thin pool usage.................................. N/A
Storage System : Checking for domain and federations health on VNX......... Pass
--------------------------------------------------------------------------------
One or more errors have occurred. Follow the instructions provided to correct
the problem and try again.
-----------------------------------Information----------------------------------
Control Station: Check if standby is up
Information HC_CS_27389984778: The standby Control Station is
currently powered on. It will be powered off during upgrade, and then
later restarted and upgraded.
--------------------------------------------------------------------------------
------------------------------------Warnings------------------------------------
Control Station: Check auto transfer status
Warning HC_CS_18800050420: Cannot establish connection to FTP server
sftphost sftp.emc.com
Action : Command "/nas/tools/automaticcollection -verifyftp" failed to
connect to FTP connection. Check the configuration in
/nas/site/automaticcollection.cfg file. For more information, search
the Knowledgebase on Powerlink as follows:
1. Log in to http://powerlink.emc.com and go to Support >
Knowledgebase Search> Support Solutions Search.
2. Use ID emc221733 to search.
--------------------------------------------------------------------------------
-------------------------------------Errors-------------------------------------
Control Station: Check for correct filesystem mount options
Error HC_CS_14505082982: The following file systems were found to be
corrupted:
* prepago on server_2
Action :
--------------------------------------------------------------------------------
[root@CS0-AYA ~]#
id = 2
name = server_2
acl = 0
type = nas
slot = 3
member_of =
standby = server_2.faulted.server_3, policy=manual
status :
defined = enabled
actual = online, active
salida desde CLI de los comandos
/nas/bin/nas_checkup
/nas/bin/nas_server -info -all
/nas/bin/nas_storage -list
/nas/bin/nas_disk -list
nas_fsck -info -all
[root@CS0-AYA /]#
[root@CS0-AYA /]#
[root@CS0-AYA /]#