Professional Documents
Culture Documents
Factories
Index Locations
4
6
General Overview 8
Types Overview 9
Materials & Finishes 11
1
Cable mANAGeMENT sYSTEMS
Cable tray Systems
Introduction
-Factories
-Locations
2 www.unimetal-ikk.com
Specialized Factory for Steel Products (Jeddah/KSA)
Sigma Factoryِ for Steel Products (Ajman & Umm Al Quwain /UAE)
Specialized Factory for Steel Products (6th of October/Egypt)
Specialized Factory for Steel Products (Amman/Jordan)
Uni-Metal cable trays and accessories from SFSP are manufactured in compliance with :
- NEMA VE 1–2009
- NEMA VE 2–2006
- IEC 61537
- BS EN 61537:2007
- BS 5750/BS EN 10130
- BS EN 10131
- BS EN 10051
- CENELEC EN 50173-1
- EIA/ITA 568 A
- ISO/IEC 11801; 2002.
Cable Trays are designed to meet most requirements of cable and electrical wire installations and comply
to local and international standards of fabrication and finishing.
This catalogue is designed to be helpful to engineers and contractors in the application and selection of tray
products for construction and maintenance.
If a unique application requires a special product not included in this catalogue , SFSP engineering personnel
are ready to furnish design consultation and realistic cost estimates. In addition, know-how are available for
your convenience.
www.unimetal-ikk.com
Cable tray Systems
www.sfsp-ikk.com 3
Cable mANAGeMENT sYSTEMS
Cable tray Systems
Factories
SFSP - Saudi Arabia SFSP - United Arab Emirates
Specialized Factory for Steel Products SIGMA Factory for Steel Products SIGMA Factory for Steel Products
Jeddah - Saudi Arabia Ajman, United Arab Emirates Umm Al Quwain, UAE
Tel : +966 2 637 4482 Tel : +971 6 743 9907 Tel : +971 6 767 0514
Fax: +966 2 636 1963 Fax: +971 6 743 9908 Fax: +971 6 767 0515
sfsp.jeddah@ikkgroup.com sfsp.ajman@ikkgroup.com sfsp.uaq@ikkgroup.com
SFSP - EGYPT
Specialized Factory for Steel Products
6th of October, Cairo - Egypt
Tel : +20 2 3831 2477
Fax: +20 2 3831 1036
sfsp.cairo@ikkgroup.com
SFSP - JORDAN
Specialized Factory for Steel Products
Amman, Jordan
Tel : +962 6 416 4216
Fax: +962 6 416 4217
sfsp.amman@ikkgroup.com
SFSP - KSA/UAE/Egypt/Jordan
Specialized / Sigma Factory for Steel Products
for Building and Construction Materials
www.sfsp-ikk.com Locations
www.sfsp-ikk.com
SYRIA
LEBANON IRAQ IRAN
Amman
JORDAN
Cairo
6th of October KUWAIT
EGYPT
Bahrain Umm Al Quwain
QATAR
Ajman
UAE
Jeddah
SAUDI ARABIA
A N
SUDAN OM
YEMEN
O/SF/GLO/LT/730/3
26-06-2008
4 www.unimetal-ikk.com
www.ikkgroup.com
DJIBOUTI
SFSP is a leading manufacturer and fabricator of steel and aluminum products used for the support of equipment
for industrial, commercial, utility and OEM installations. Our customers have access to the most complete support
systems offered in the industry including metal framings, cable trays, pipe hangers, slotted angles, fasteners
and others.
(Our factory is equipped with an in-house hot dip galvanization facility) .
CNC Machines
www.unimetal-ikk.com
Cable tray Systems
5
Cable mANAGeMENT sYSTEMS
Cable tray Systems
Uni-Metal trades in-house produced steel construction products, all designed and manufactured in SFSP plants
located in KSA,UAE,Egypt and Jordan.
S ALE SArabia
Saudi
Norway
Sweden
Estonia
Russia
Latvia
Denmark Lithuania
Ireland
United Belarus
Netherlands
Kingdom
Belgium Poland
Germany Astana
Stuttgart Czech Rep
Slovakia Ukraine
Maldova Kazakhstan
Austria Hungary
Switzerland
Mongolia
France Romania
Croatia
Serbia
Italy
Bulgaria Georgia
Albania Istanbul
Uzbekistan Kyrgyzstan
Baku
Azerbaijan
Portugal Spain Armenia
Greece Turkey Turkmenistan
Tajikistan
Ashgabat
TUNISIA
Oran Algeria
Malta
Beirut SYRIA Kabol
Tanger
Casablanka LEBANON
Irbil
Afghanistan China
IRAQ Tehran
MOROCCO Amman
Banghazi
Tripoli JORDAN Gurayyat
IRAN Pakistan
Skakah KUWAIT
ALGERIA Cairo Aqaba Kuwait
Hafr Al Batin Nepal
LIBYA 6th of October
Tabuk Jubail
BAHRAIN
Hail Qassim Manama
Dammam UAQ
EGYPT Ma dinah Riyadh
Sharjah
Doha Dubai
Ajman
QATAR
Yanbu Hufuf
Musaffah Bangladesh
Al Kharj Jebel Ali
Jeddah UAE India
Mauritania Mak kah Muscat Myanmar
Al Taif SAUDI ARABIA
Laos
AN
Khamis Mushayt
Mali Baha
OM
Equatorial
Guinea Bata Uganda Indo
Libreville Kenya
Congo
Gabon
DR Congo
United
Republic of
Tanzania
Luanda
Angola
Zambia Malawi
Mozambique
Zimbabwe
Namibia
Windhoek Botswana
Gaborone
Managing Office
Main Branch
South
Branch Africa
Factory
Design Office
Purchasing & Supply
Up-Coming Branch
Up-Coming Factory 2010
6 www.unimetal-ikk.com
Khamis Mushayt Baha Najran Gizan Riyadh
Tel : +966 7 237 5929 Tel : +966 7 237 5929 Tel : +966 7 321 4038 Tel : +966 7 321 6660 Tel : +966 1 454 9282
Fax: +966 7 237 8783 Fax: +966 7 237 8783 Fax: +966 7 321 4035 Fax: +966 7 321 0665 Fax: +966 1 456 6627
unitech.ksa@ikkgroup.com unitech.ksa@ikkgroup.com unitech.ksa@ikkgroup.com unitech.ksa@ikkgroup.com unitech.ksa@ikkgroup.com
Hufuf
Tel : +966 3 586 9732
Fax: +966 3 584 5966
unitech.ksa@ikkgroup.com
Korea
Taiwan
SHARJAH ABU DHABI / Musaffah
Tel : +971 6 534 4092 Tel : +971 2 551 2334
Fax: +971 6 534 8949 Fax: +971 2 551 2335
unitech.uae@ikkgroup.com unitech.uae@ikkgroup.com
EGYPT
CAIRO GHOMHOURIYA STREET
Tel:+20 2 346 8566 Tel : +20 2 787 2152
Fax:+20 2 346 8567 Fax: +20 2 593 1053
unitech.egypt@ikkgroup.com unitech.egypt@ikkgroup.com
Australia
MATERIALS & PURCHASING
CPU - KSA / JEDDAH Tosl - UAE / JEBEL ALI CHINA - Yiwu
www.unimetal-ikk.com
Sydney Tel : +966 2 627 8275 Tel : +971 4 886 0262 Yiwu - Zhejiang Province
New Zealand
Fax: +966 2 627 8727 Fax: +971 4 886 0261 Tel : +86 579 8545 3180
cpu.jeddah@ikkgroup.com tosl.jxb@ikkgroup.com Fax: +86 579 8542 7682
unitech.china@ikkgroup.com
7
Cable mANAGeMENT sYSTEMS
Cable tray Systems
General Overview
-Types Overview
-Materials & Finishes
-Technical Data
8
General Overview
- MATERIALS
- MATERIAL THICKNESS
1.00 mm 1.20 mm 1.50 mm 2.00 mm
Light Duty - Cable Tray System Medium Duty - Cable Tray System
LCT - 100 MCT - 120
Heavy Duty - Cable Tray System Very Heavy Duty - Cable Tray System
HCT - 150 VCT - 200
All illustrations, drawings and descriptive material in this publication are of a generally informative nature only,
and do not form a complete package of the specifications or description of the goods .
Most of the dimensions shown are nominal .
Uni-Metal can make modifications and design, materials or finishes as it deems necessary or desirable .
9
Cable mANAGeMENT sYSTEMS
Cable tray Systems
. Straight STR
w
Return Flange Outside RFO
e
. C-Type Outside CTO
i
v
- SHAPES OF ACCESSORIES
. Cornered . Curved
r
e
v
- TYPES OF PERFORATION
O
Staggered
. Serial
15
l
L
a
Oblong holes
r
W
7 x 32
- DIMENSIONS
15
e
L
n
25
25
e
H 25 25
W
Oblong holes
7 x 32
32
G
.
25
25
All dimensions are in mm
10
25 25
Materials & Finishes
Materials
Mild Steel - Plain
A. Hot Rolled Steel Plates, Sheets and Coils S235 JR,
As per:
EN 10025 -2 / DIN 17100 / BS 4360 / ASTM A 653M / ASTM A 1011
/ ASTM A 1011-01a
JIS 3101 / JIS 3106 / GB 700 / GB / T1591.
ASTM A 907 / ASTM A 1018M.
ASTM A 570M / ASTM A 572M.
B. Cold Rolled Steel DC 01,
As per:
EN 10130 / DIN 1623, Part 2 / BS 1449:1 / ASTM A366 / ASTM A 1008 / JIS G 3141 /
GB 699.
EN 10131 / ASTM A 568M
Stainless Steel
F.Austenitic Stainless Steels AISI 304 & 316,
As per:
ASTM A 240 /EN 10088-2/ DIN 17400 / BS 1449:2 /
ASTM A480 / ASTM A666 / ISO 3506 / EN 10028-7 /JIS G 4304
F.1 Stainless Steel Fasteners EN 3506
F.2 Stainless Steel Wire BS 1554 ,ASTM A276
Aluminium
G.Aluminium 5052 & 6063
Finishes
1- Hot–DIP Galvanization After Fabrication
As per:
ASTM A 123 / ASTM A 153 / ISO 1461.
BS 729 / DIN 50976
As per:
ASTM B633 / EN 12329 / ISO 4042/ BS 1706 / BS 3382 / DIN 50961
Cable tray Systems
3- Powder Coating
Epoxy / Polyester / Epoxy & Polyester
BS 3900 / ISO 2409 / ISO 1519 / ISO 1520
11
Cable mANAGeMENT sYSTEMS
Cable tray Systems
12 www.unimetal-ikk.com
Light Duty Cable Tray Runs
LCT - 1.00 mm Thickness
13
Cable mANAGeMENT sYSTEMS
Cable tray Systems
14 www.unimetal-ikk.com
Medium Duty Cable Tray Runs
MCT - 1.20 mm Thickness
1.50 0.19
2.00 0.09
MCT 400 - 25 1.00 0.24
width (w) : 400 1.20 0.15
1.50 0.08
2.00 ….
MCT 450 - 25 1.00 0.17 50
50
width (w) : 450 1.20 0.11
32
7
1.50 …. 32
7
2.00 ….
Order Example:
MCT25 - Side height (h) - Width(w) - Thickness - Side type
for more ordering details, please check pages (61-62)
15
Cable mANAGeMENT sYSTEMS
Cable tray Systems
32
Width Order Example 25 25 7
(mm) Item (h) (w) (t) type
50 MCT50 050 0050 2 RFI
100 MCT50 050 0100 2 RFI 32
7
Order Example:
MCT50 - Side height (h) - Width(w) - Thickness - Side type
for more ordering details, please check pages (61-62)
16 www.unimetal-ikk.com
Medium Duty Cable Tray Runs
MCT - 1.20 mm Thickness
25 25
Width Order Example
(mm) Item (h) (w) (t) type 25 25
100 MCT75 075 0100 2 RFI
150 MCT75 075 0150 2 RFI
25 25
Order Example:
MCT75 - Side height (h) - Width(w) - Thickness - Side type 25 25
for more ordering details, please check pages (61-62)
32
7
www.unimetal-ikk.com
32
7
Cable tray Systems
17
Cable mANAGeMENT sYSTEMS
Cable tray Systems
1.50 0.94
2.00 0.50
25
Order Example 25 25
Width
(mm) Item (h) (w) (t) type 25
100 MCT100 0100 0100 2 RFI
150 MCT100 0100 0150 2 RFI 25 25
Order Example: 32 25
25 7
MCT100 - Side height (h) - Width(w) - Thickness - Side type
for more ordering details, please check pages (61-62)
32
7
18 www.unimetal-ikk.com
Heavy Duty Cable Tray Runs
HCT - 1.50 mm Thickness
19
Cable mANAGeMENT sYSTEMS
Cable tray Systems
20 www.unimetal-ikk.com
Heavy Duty Cable Tray Runs
HCT - 1.50 mm Thickness
7
width 700 mm 1.20 0.63
Cable tray Systems
1.50 0.37
2.00 0.16
21
Cable mANAGeMENT sYSTEMS
Cable tray Systems
1.50 1.67
2.00 1.00
2.50 0.63
HCT 500 - 100 1.00 1.49 25
Width Order Example
width (w) : 500 mm 1.20 1.49 (mm)25 Item (h) (w) (t) type
1.50 1.49 100 HCT100 0100 0100 3 RFI
150 HCT100 0100 0150 3 RFI
2.00 0.80
HCT 600 - 100 1.00 1.22 25 25
Order Example:
width 600 mm 1.20 1.22 HCT100 - Side height (h) - Width(w) - Thickness - Side type
32
7
for more ordering details, please check pages (61-62)
1.50 0.98
2.00 0.50
HCT 700 - 100 1.00 1.02
width 700 mm 1.20 1.02
1.50 0.67
2.00 0.33
22 www.unimetal-ikk.com
Very Heavy Duty Cable Tray Runs
VCT - 2.00 mm Thickness
Order Example:
VCT25 - Side height (h) - Width(w) - Thickness - Side type
for more ordering details, please check pages (61-62)
23
Cable mANAGeMENT sYSTEMS
Cable tray Systems
24 www.unimetal-ikk.com
Very Heavy Duty Cable Tray Runs
VCT - 2.00 mm Thickness
1.50 2.65
2.00 1.45
VCT 500 - 75 1.00 2.70 Cable tray Support distance (m) Load kN/m
width (w) : 500 1.20 2.70 VCT 900 - 75 1.00 1.30
25 width (w) : 900 1.20 0.86
1.50 2.10
2.00 1.13 25 1.50 0.50
VCT 600 - 75 1.00 2.22 2.00 0.21
width (w) : 600 1.20 2.22 VCT 1000 - 75 1.00 1.01
25 25
1.50 1.38 width (w) : 1000 1.20 0.65
2.00 0.73 1.50 0.36
32
VCT 700 - 75 1.00 1.87 7 2.00 0.13
width (w) : 700 1.20 1.58
1.50 0.95
Width Order Example
2.00 0.49 (mm)
www.unimetal-ikk.com
25
Cable mANAGeMENT sYSTEMS
Cable tray Systems
26 www.unimetal-ikk.com
Cable Tray Fittings
- Bend 45° - Vertical 90° Outside Riser
- Bend 90° - Vertical 90° Inside Riser
- Intersection - Adjustable Riser
- Tee Branch - Reducer
- Add-on Branch
Cable tray Systems
27
Cable mANAGeMENT sYSTEMS
Cable tray Systems
160
161
170 171
Radius
r = 200 mm
28
Cable Tray Fittings
Bend 90° (cornered / curved)
240 241
242
250 251
Cornered/Short
Radius
r = 200 mm
www.unimetal-ikk.com
Cable tray Systems
Order Example: Order No. shall be the same as curved type,but add the letter T .
250 - Side height (h) - Width(w) - Thickness - Side type ex: 250 050 0050 2 ; Curved type
for more ordering details, please check pages (61-62) 250T 050 0050 2 ; Cornered/Short type
29
Cable mANAGeMENT sYSTEMS
Cable tray Systems
320 321
322
330 331
30 www.unimetal-ikk.com
Cable Tray Fittings
Intersection (cornered / curved)
- Intersection - cornered
400 - 401
400 401
- Intersection - curved
410 - 411
www.unimetal-ikk.com
410 411
Cable tray Systems
31
Cable mANAGeMENT sYSTEMS
Cable tray Systems
480 482
481
Width Order Example
(mm) Item (h) (w) (t) type Order Example:
50 480 050 0050 2 RFI 480 - Side height (h) - Width (w) - Thickness (t) - Side type
100 481 050 0100 2 RFI for more ordering details, please check pages (61-62)
32 www.unimetal-ikk.com
Cable Tray Fittings
Vertical 90 inside riser (cornered / curved)
o
560 562
561
Width Order Example
(mm) Item (h) (w) (t) type Order Example:
50 560 050 0050 2 RFI 560 - Side height (h) - Width (w) - Thickness (t) - Side type
100 561 050 0100 2 RFI for more ordering details, please check pages (61-62)
www.unimetal-ikk.com
Cable tray Systems
33
Cable mANAGeMENT sYSTEMS
Cable tray Systems
- Adjustable riser
640
- Custom risers
60°
For inquiries, use same code as adjustable risers and add the angle desired at 45°
the end, ex:
681
W2
680
Order Example: h
680 - Side height (h) - Width (w1) - Width (w2)- Thickness (t) - Side type W1
for more ordering details, please check pages (61-62)
34
Cable Tray Fittings
Reducer (central / right / left)
- Right side
690 - 691
690
691
- Left side
700 - 701
700
701
Width Order Example
(mm) Item (h) (w1) (w2) (t) type Order Example:
50 700 050 0300 050 2 RFI 700 - Side height (h) - Width (w1) - Width (w2)- Thickness (t) - Side type
100 701 050 0400 050 2 RFI for more ordering details, please check pages (61-62)
www.unimetal-ikk.com
Cable tray Systems
35
Cable mANAGeMENT sYSTEMS
Cable tray Systems
36 www.unimetal-ikk.com
Cable Tray Accessories
- Connector - End Plate
- Barrier Strip - Drop-out Plate
- Joint Plate - Cable Tray Cover
- Reducing Angle - Framing System Acc.
Cable tray Systems
37
h
240
- Straight connector h
1000
h
Order Example
240 Item (h) (t)
240 1000 050 2
h 1000 100 2
Order Example:
1000 1000 - Side height (h) - Thickness (t)
for more ordering details, please check pages (61-62)
h
- Angle connector 20
1010/1020
240
240
240
h
h
h
20 20
1010
50
1020
Width Order Example
(mm) Item (h) (w) (t)
20 1010 050 0020 2 Width Order Example
(mm) Item (h) (w) (t)
Order Example:
240
1010 - Side height (h) - Width (w) - Thickness (t) 50 1020 050 0050 2
240 240
for more ordering details, please check pages (61-62) Order Example:
1020 - Side height (h) - Width (w) - Thickness (t)
h
for more ordering details, please check pages (61-62)
h
- Adjustable connector
50 h
1030/1040
50
50
120
120
For M6 Bolt
1030
7 x 38 for M6 Bolt
1040
Order Example Order Example:
Item (h) (t) 1030 - Side height (h) - Thickness (t)
1030 050 2 for more ordering details, please check pages (61-62) Order Example Order Example:
Item (h) (t) 1040 - Side height (h) - Thickness (t)
1040 050 2 for more ordering details, please check pages (61-62)
38 www.unimetal-ikk.com
Framing System Accessories
240
150
h h
240
50
25 1070
1050 1060
-Available with differnt side height types.
150
h
W
W
W=
w
min
us
1080 7m
1100
m
1110
G H B
D E C
Functions
Cable tray covers shall be considered for any of the following purposes:
• Protection from falling objects or debris, as may occur beneath personnel walkways.
• Shielding from ultra-violet rays of the sun and guarding against other weathering elements.
• Minimizing accumulation of foreign contaminants such as ash or other industrial deposits.
• Protection of cables and personnel where a riser tray penetrates a floor or grating.
2010
2000
Locking clamp
Thickness: 2mm
2100
40 www.unimetal-ikk.com
9021 M 16 M 16 50 17 3
FR AMI NG SY STEMOrder
S ACCExample: WA - ZP - M 12 - DIN 9021
ESSORI ES
Threaded Rods, Hexagon Head Bol ts, Nuts, Washers
S
M 8 M 8 1000
6 1000 440 9021 M 22 6,6 8,4
M8M 8M 8 M8 MM168 8 8.4 1000 1.6 164,0 8,4 1,6
S
9021 M 89021 M8
M 8 M8
24 8,4 24 2 8.4 2
M 10 M 10
M 10 M10
1000
M2110
6,4
1000 2 6,4 9021
9021
M 10
MM10
10 30 10,5
M 10 30 10,5
M10M 10 M 10 10.5 21 10,5 2 9021 M10 M10 302,5 10.5 2.5
d M 12 MM1212 M 1000
12
13 12,92.5
1000 12,9 440 440
M 12 M 12 45 13,5 4 45 13,5
M12
M 12M 16
M12
M
24
M1612 1000 2417,3 13 2,5
d d 9021
440
M 12
M12
M 12 37 13
45
3
13.5 4
D M 16 M16 M 16M16 1000 17 17,3 3
30 D 9021 9021 M 12
M12 M12 M 12
17 37 3 13 337 13
or ,Throught Anchor ....... M 16
Order M ×16
Example : TR - ZP - M 12 1000 30 17 3 D 9021 M 16 M 16 50
or ,Throught Order
Anchor ....... : TROrder Example: SRW - M 12 -DIN 115 9021
Order 9021 WA -M
Example: ZP 16
M16- M 12 - DINM16
9021 M5016 17 350 17
Example -Order
ZP - M 12 × 1000
Example: WA - ZP - M 12 - DIN 125 Order
Order Example:
Example: SRW - MWA - ZP
12 - DIN - M 12 - DIN 9021
9021
axbxd
Load Square Washers SSW H.D. Galvanised Stainless Steel a x b x d
cap. H.D. Galvanised
Load for Bolts - HDG Stainless
for BoltsSteel Zinc Plated Stainless Steel
D d s
cap. [mm]
Square Washers (SSW) for Bolts - HDG for Bolts for bolt - ZP for bolt
[kN] [mm] [mm] [mm] [mm]
M 10 M 10 40 x 40 x 5
[kN]
S
d M 6 M 6 12 6,4 1,6
2,2 SSW 40/40 M
M 10
12 SMM 10
12S 40
40 xx 40
40 xx 55
ZincdPlated Stainless Steel M 8 M 8 16 8,4 1,6 D d
2,2
4,0 for all channels a b
Dimension- ZP M 12
Dimension
DIN
M 12
EN
40
40 x 40 xx 55a xd b x d
x 40 Zinc Plated Stainless
21 2 Steel
a M 16
H.D. Glavanized
[mm]M 16
Stainless
[mm] Steel M 10 M 10 10,5
4,0 41/21 Series b
6,4 M 6 x 12 M 16 for Bolt M 16 for Bolt 40 x 40 x 5 D M 12 for bolt
M 12- ZP 24 for bolt
13 2,5
6,4 10 10 (mm) M 16 M 16 30 17 3 [mm] [mm]
9,3 M 6 x 25
M6 M10 40 x 40 x (4-5-6) Order Example: WA - ZP - M 12 - DIN 125
M M 6 M 6 40 x 40 x 6
S
9,3
17,3 SSW 41/41 M 8 x 25 8 x 25
13 13 M 6 M 6 12 6,4
M 6 SM 6M10
S M12 40 x 4040
x 6x 40 x (4-5-6)
M 8dx 40 M 10 M 10 40 x 40 x 6
17,3
27,0 for allZinc
channels
Plated Stainless Steel
M12 M16 40 x 40 x (4-5-6) M 8 M 8 16 8,4
dx 20
M 10 DIN EN 40
41/41 Series M
M 10 M 10 40 xx 40
40 xx 66
27,0 Dimension- ZP a bM 10 x 30
Dimension Order 12
M 10Example:
x 30
M 12
SSW 41/41 - M 12 - d
d M 10 M 10 21 10,5
a bM 10 x 45 M 12 [mm] [mm]
M 10 x 45 M 12 40 x 40 x 6
17 16 M 12 M 12 24 13
M Order
6 x 12Example:
FR AMI NG
M 10 x 60
D
M SY
SW STEM
1041/41
x 70 S ACC
- HDG ESSORI
- M 12
10 10ES M 16 M 16 30 17
Load
Fully Threaded
M Order Rods
6 x 25Example: Grade
SW 41/414.6- DIN
HDG 975
- M 12 Round Head Machine Screws
S
cap.
Load
M 12 x 22
Threaded Rods, Hexagon Head Bol ts, Nuts, Washers
cap. M 8 x 25 M 12 x 25
M 8 x 25 M 12 x 25 Order Example: WA - ZP - M 12 - DIN 125
[kN] M 12 x 30 M 12 x 13
30 13
Threaded Rod (STR) Zinc Plated Length Length Load
Load cap. Round Head (SRH) Zinc Plated d Length d
M 8 x 40 Zinc
M 12 xPlated
40 Stainless
M 12 x 40Steel
D s
[kN]
6,4
DIN 975 Thread (mm) 19 18(KN)
cap. DIN 7985 Zinc Plated Stainless Steel
Thread (mm) (mm)
Thread
M 12 x 50- ZP Thread for bolt - ZP for bolt
M 10 x 20 [mm] [kN] DIN [mm] [mm] [mm]
6,4
9,3 M 12 x 60 M6 M 12 x2000/3000
60 2.2 M6 30-40 6.0
9,3 M 10 x 30 MM 10
12M 6x
x 80 30
M8
M 6
M 12 x 80
2000/3000
1000 2,2
4.0
440 M 6
M8
22 6,6
30-40
2
8.0
17,3
S
M 12Mx 90
8 M 8 1000 4,0 9021 M 8 M 8 24 8,4 2
17,3 M 10 x 45 M 10 x M1045 2000/30001000 6.4 M10 30 10,520-60 10.0
M 16Mx10
40 17
M x10
M 16 40 16 6,4 9021 M 10 M 10 2,5
M12 2000/3000 24 2412.9
M 10 x 60 M 16Mx12
60 M x12
M 16 60 1000 12,9
d 440 M 12 Order Example:
45 SRH - M4 10 - DIN 7985
13,5
M 16Mx16
90 M16 M x16
M 16 2000/3000
90 1000 17,3
17.3 9021 M 12 M 12 37 13 3
M 10 x 70 D
9021 M 16 M 16 50 17 3
S
OrderOrder
Order Example
Example : :HB
TR -- ZP
Example ZP - -MM12
: STR -12
M××12
1000
1000
M 12 x 22 Order Example: WA - ZP - M 12 - DIN 9021
Material & Finishes Codes
M 12 x 25 M 12 x 25
Material & Finishes Codes
M 12 x 30 M 12 x 30 fv = h.d. galvanised, strength grade 4.6
Roofing Bolts S/m S/m e
fv = h.d. galvanised, strength grade 4.6
M 12 x 40 M 12 x 40 gv Steel= electroplated,
Zinc Plated Stainless
DIN ISO
strength grade 4.6 gv = electroplated, strength grade 4.6
D d s
Thread - ZP Thread 19 18 Zinc Plated Stainless Steel
Min. Roofing
M bolts
12 x 50 fv 8.8 = [mm]
h.d. galvanised
[mm] [mm] ,strength grade 8.8 fv 8.8 = h.d. galvanised ,strength grade 8.8
Drill
Min.hole M410/ 5 M5 11,5M6 M8 - Materialsfor: bolt
low- ZP
carbon forsteel
gv 8.8 bolt
= , carbon
electroplated, steel
strength grade 8.8
(SRB) M 6 M 6
Thread Sizegv 8.8 x =
10/ 6
- yelectroplated,
[mm] [mm] [mm]
Drill hole M 12 x 60 MM 12
8 x 60
- y 15,0xstrength
x13/7,5 -y x -grade
y 8.8
- Steel S235 ,Mgrade 4.6 ,M4.8
(mm) 6 and 12 8.8grade6,4A4-501,6
A4-50 = Stainless steel
M 8 (mm)13/6,5 (mm)
S
(mm) (mm) 6
(mm) M 12 x 80 M 10Plated
M 12 x 80
Zinc A4-50
M 10
Stainless= Stainless
17/
Steel
S
8 16/ S9,5steel
19,6 grade A4-50 A4-70 = Stainless steel grade A4-70
55 e
M 12 Length M 12 10 - 50 DIN
19/10 1018/12
EN
- 80 21,9
12 - 120 16 - 150 - Surface : plain , black , zinc plated 8,4 1,6
M 8 M 8 16
= Stainless steel grade A2-50
A2-50M 10
55 Dimension- ZP Dimension d M 10 21 10,5 2
16 - M = Stainless
24/15,5steel
[mm] [mm]grade A4-70
60 M 12 x 90 M 16 Example :A4-70
Order MSRB 6 24/13 27,7 - Length = X (mm)
M 12 – Y (mm) = Stainless steel
A2-70M 12 24 grade
13A2-702,5
D
m
60 M 6 x 12
S
= Stainless steel
HCR M 16 30 W1.4529
17 HCR-50
75 M 16 x 40 M 16 x 40 A2-50 = Stainless
M 6 x 25
10 steel
10 grade A2-50 M 16 3
75 24 24 Order Example: WA - ZP - M 12 - DIN 125 ( S. 53)
90 M 16 x 60 M
M 816 x 60
x 25 A2-70 = Stainless
M 8 x 25
13 steel
13 grade A2-70
90 M 8 x 40
M 16 x 90 M 16 x 90
M 10 x 20 HCR = Stainless steel W1.4529 HCR-50
M 10 x 30 M 10 x 30
Order Example : HB - ZP - M 12 × 1000
M 10 x 45 M 10 x 45
( S. 53)
17 16
M 10 x 60
Pull-outMvalues
10 x 70 in KN -concrete R 250kg/cm2 (1KN=100kg)
S
Pull-outMvalues
12 x 22 in KN -concrete R 250kg/cm2 (1KN=100kg)
max Yellow zinc plated Stainless Steel Material & Finishes Codes
ixing
max
Carriage Bolts with Nut
Type Below
M 12 x 25 Head M
Steel Thread
Yellow
DIN
12 x 25603
(Zn)
zinc plated Stainless Steel
M 12 x 30 M 12 x 30 Thread
xing
mm) Type Steel Thread
Pull (Zn) fv = h.d. galvanised, strength
H Max Torque
S/m Shear
M 12 xS/m Thread
Max Torque Pull
e Shear
www.unimetal-ikk.com
M 12 x 40 40
mm)
5
Zinc Plated
Carriage bolts Stainless Steel
P M 12Max
(mm) Out
x 50Torque Pull Shear
(mm)
Max 19
Out
Torque18 Pull Shear = electroplated, strength
gv
M6 DIN ISO H.D.
(STC) (mm)
10 Out
10.3M 12 9.6 (mm)
8 Out
9.5 8.4
5 Thread - ZP Thread M 12 x 60 x 60 Zinc Plated Glavanized Head Head Square Width Square Depth
fv 8.8 = h.d. galvanised ,strength
Cable tray Systems
10 M
M 68 M 12 x 801025
[mm]
10.3 [mm]
9.6
12.2M 1217.5
x 80 E[mm]
819 9.5
14 (E) 8.4
15.4 Grade 4.6 (A) mm (H) mm (O) mm (P) mm
10
20 M 8 M 12 x 9025
5 17.5
12.2 19 14 (E) gv 8.8 = electroplated, strength g
M 6 MM 10 6 45 10/ 17.1 10/ 6 11,5
27.8 38 19 15.424.4
20
25 M 10
M 16 x 40 M 16 x 40
M 8 MM 45 17.1
12 M8 16 x 6075 13/6,5 27.8
25.3M 1613/7,5
40.5
x 60
38
24
15,0
2419 M5
24.4 M5 12.0 3.0 5.0 A4-50 =3.2
Stainless steel grade A4-
25 M 12 M 16 x 9075 M6 M6 15.1 3.70 6.40
M 10 M 10 17/25.3
M 1640.5
8 16/
x 90
9,5 19,6
its is advisable to apply safty factor in consideration of the various
A4-70 =4.0
Stainless steel grade A4-
e ways
its of employment
isOrder Example
advisable : HB - ZP
to apply - MOfactor
safty 12 × 1000
in consideration of theM8
various M8 18.3 4.50 8.23 A2-50 =4.75
Stainless steel grade A2-
M 12 M 12
ways of employment
19/10 18/12 21,9
M10 M10 21.44 5.30 9.86
M 16 M 16 24/13 24/15,5 27,7 A2-70 =5.56
Stainless steel grade A2-
Material & Finishes Codes
M16 M16 34.14 8.74 16.3 8.74
S
fv HCR
= h.d. galvanised, = Stainless
strength grade 4.6 steel W1.4529 H
S/m S/m e
Zinc Plated A
Stainless Steel
DIN ISO
Order Example : STC - M 6 gv = electroplated, strength grade 4.6
Thread - ZP Thread
[mm] [mm] [mm] fv 8.8 = h.d. galvanised ,strength grade 8.8 41
M 6 M 6 10/ 5 10/ 6 11,5 gv 8.8 = electroplated, strength grade 8.8
M 12 x 90
M 16 x 40 M 16 x 40
24 24
M 16 x 60 M 16 x 60
Cable mANAGeMENT sYSTEMS
FR AMI NGM 16SY STEM S ACC
x 90 M 16 xESSORI
90 ES Cable tray Systems
Order
Threaded Example
Rods, : HB - ZPHead
Hexagon - M 12 Bol
× 1000
ts, Nuts, Washers
S
M 8 M 8 1000 4,0 M 8 M 8 24
M 6M 10 gv 8.8 = electroplated,
M6 M 6 M 10 10/ 5 10006M6 11,5
10/ 6,4 10/5 10/6 902111.5 M 10 M 10 30 1
M 8M 12 M8 M 8 M 12 13/6,5 1000
13/7,5M8 12,9
15,0 13/6.5 13/7.5 44015.0 A4-50 = Stainless steel
M 12 45 1
d
M 10M 16 M10M 10 M 16 17/ 8 16/
10009,5 19,6
M1017,3 17/8 16/9.5 902119.6 M 12 M 12 = Stainless
A4-70 37 steel
e D
M 12 M12M 12 19/10 M12 21,9
18/12 19/10 18/12 902121.9 M 16 M 16 = Stainless
A2-50 50 steel
Order Example : TR - ZP - M 12 × 1000
M 16 M16M 16 M16 27,7
24/13 24/15,5 24/13 24/15.5 A2-70
27.7Order Example: WA - ZP = Stainless
- M 12 steel
- DIN 9021
m
S
(mm) (mm) M 6 M 6 12 6
EN 24017 S S
Zinc Plated Stainless Steel M 8 M 8 16 8
(without nut) M 6 x 12 DIN EN
Dimension- ZP Dimension 10 d 10 M 10 M 10 21 10
M 6 x 25 [mm] [mm]
M 12 M 12 24 1
M 6 x 12 M 8 x 25 M 8 x 25 D
10 10 13 13 M 16 M 16 30 1
M 6 x 25 M 8 x 40
M 8 x 25 M 10 x 20 M 8 x 25 Order Example: WA - ZP - M 12 - DIN 125
13 13
M 8 x 40 M 10 x 30 M 10 x 30
M 10 x 20 M 10 x 45 M 10 x 45 17 16
M 10 x 30 M 10 x 60 M 10 x 30
M 10 x 45 M 10 x 70 M 10 x 45
17 16
M 10 x 60 M 12 x 22
M 10 x 70 M 12 x 25 M 12 x 25
S
M 12 x 22 M 12 x 30 M 12 x 30
M 12 x 25 M 12 x 40 M 12 x 25 M 12 x 40
19 18
M 12 x 30 M 12 x 50 M 12 x 30
M 12 x 40 M 12 x 60 M 12 x 40 M 12 x 60
19 18
M 12 x 50 M 12 x 80 M 12 x 80
M 12 x 60 M 12 x 90 M 12 x 60
M 12 x 80 M 16 x 40 M 12 x 80 M 16 x 40
M 12 x 90 M 16 x 60 M 16 x 60 24 24
M 16 x 40 M 16 x 90 M 16 x 40 M 16 x 90
24 24
MOrder
16 x 60
Example : SHB - M
M 16
12 x 60
M 16 x 90 M 16 x 90
42 www.unimetal-ikk.com
Cable Tray Support System
- C - Channel - Wall Bracket
- Cantilever Arm - Support Accessories
- U - Support
- I - Support
43
Cable mANAGeMENT sYSTEMS
Y Y Cable
Y tray Systems
Z
Z
Z Z
- C-Channel Systems Z
Z
Z
Z Z
Z
Channel
Z
Uni-metal’s framing channel is cold formed on modern Y
Y
Y Y
Y
Y
Y
Y
Y Y
Y
Y
rolling machines from low carbon steel strips. Y Z Y Y Y
A continuous slot provides the ability to make attachments Y
21.0 Y Y 41.0
at any point. Z
Z
Z
Z Z
Z
Lengths 41.0 Z Z Z
Standard length: 3000 mm with ± 3.2mm length tolerance. Z 41.0
41.0
13
50
Material Thickness Size Channel Patterns 30 41.0
2 for 1.5 mm 2 - 21/41 mm 0 - PT 41.0 41.0
3 for 2.0 mm 4 - 41/41 mm 1 - ST 41.0
4 for 2.5 mm 2 - B2B
13
13 50
13
50
50 30
13 30 30
50
30
For more information on Uni-channel Systems , Uni-Metal technical staff will be ready to assist you with all necessary details.
www.unimetal-ikk.com
44 www.unimetal-ikk.com
Cantilever Arm Bracket
- CCH441 41x41x2.5
3.0
450 1.80 0.90 8.8
2.0 600 1.35 0.65 8.8
1.0
700 1.15 0.55 8.8
800 0.95 0.45 8.8
0.0 A(mm)
900 0.90 0.40 8.8
4.0
2.0
F1 or F2
Fz
25
0.0
www.unimetal-ikk.com
h
Cable tray Systems
h-50
1/2 A 1/2 A
FD Length A (mm)
25
b t
Fv =F1 + F2 * Given Loads are always in [kN] “ Allowable characteristic live load “
45
Cable mANAGeMENT sYSTEMS
Cable tray Systems
0.0
6.0
450 4.60 2.35 14.7
4.0 600 3.50 1.75 14.7
2.0 700 3.00 1.50 14.7
0.0 800 2.65 1.30 14.7
A(mm)
900 2.35 1.15 14.7
F1 F2 1000 2.10 1.00 14.7
F1 or F2
Fz
25
h
h-50
FD
25
1/2 A 1/2 A
b t Length A (mm)
Fv =F1 + F2 * Given Loads are always in [kN] “ Allowable characteristic live load “
46 www.unimetal-ikk.com
Cable Tray Support System
- U - Support
3000
200
140
100 70
5 13x30
200
25 140
13x30 U-Support with welded-on head plate
200
100
140 70
200 x 100 x 5mm
42 80
100 70
Order Example
3000 Item (L) (t)
5 13x30
13x30
3000 0200 5
5
Order Example:
3000 - Length (L) - Thickness (t) 25
25
for more ordering details, please check pages (61-62)
13x30
200 13x30
140
42 80
100 13x30 70
42 80
5 13x30
3050
Order Example:
25
3050 - Length (L) - Thickness (t)
for more ordering details, please check pages (61-62)
13x30
42 80
- Wall Bracket
3200 - 3250
47
Cable mANAGeMENT sYSTEMS
Cable tray Systems
3300 3350
- Angles
3600
3600
48 www.unimetal-ikk.com
Heavy Duty Anchors
- Expansion Steel Anchor - STM
- Drop-in Anchor - SDA
- Sleeve Anchor - SAS / SAB
- Through Bolt (Wedge Anchor) - STB
- Shield Anchor - SSA
Cable tray Systems
49
Cable mANAGeMENT sYSTEMS
Cable tray Systems
Direction of Loading
Tensile Loads
Tensile loads are applied along the axis of fixing
(see Fig.1).
Fig.3 Fig.3
Common examples include suspended ceiling
applications and the suspension of mechanical services,
pipework , ductwork ,etc ...
Shear Loads
Fig.4
Shear loads act at right angles to the axis of fixing and
directly against the face of the structural material Fig.4
(see Fig.2).
Shear performance is governed mainly by the shear
strength of the bolt material and by the comperssive
strength of the supporting substrate.
Slotted Holes in Fixture
When fixing anchors through slotted holes; it is important
Oblique / Combined Loads to ensure that there is an adequate surface of contact
Oblique loads are a combination of tension and shear between the washer and the fixture to guarantee
components (see Fig.3). a positive clamping force.
If the angle of the applied oblique load is within 10˚ of If in doubt, a square plate washer with a thickness of
pure tension or pure shear, the safe working load for 3mm or above would be recommended in place of the
that direction may be assumed. Otherwise, the applied standard washer supplied.
oblique load shall be resolved into its shear and tensile
components. Diamond Drilled Holes
When holes are formed in the structure using a diamond
drilling system; extra care is required to ensure the holes
Offset Loads are thoroughly cleaned by brushing and blowing for at
Offset loads act at right angles to the fixing axis but are least three times. Also, to make a key for the anchor
offset from the surface (see Fig.4). (particulary if a bonded anchor is installed) the sides of
In this situation, the deflection of the bolt due to bending the hole shall be roughened up by inserting a standard
needs to be considered as well as the shear capacity of masonry bit into the hole attached to a hammer action
the anchor. drilling machine.
A resin with minimal shrinkage shall be selected for
diamond drilled holes.
50
s Yellow
Order zinc
example:
plated Stee
Thread (Zn
Heavy Duty Anchors
M6
M8
Expansion Steel Anchor - STM M 10
M 12
Yellow zinc
Features: plated Steel
- Suitable for all screws or threaded bolts with metric thread. STM Order
Threadexamp
(Zn)
- Low energy impact, power-saving assembly. Expansion Steel Anchor
M6
- Multiple removing and fixing. M8
- Inside threaded anchor, allows great flexibility. M 10
- Can use variable lengths and art of threaded rods or bolts. Yellow
M 12 zinc
- Small edge distance and small distance between anchors. plated Stee
STM/H Thread (Zn
- Provide uniform load by tightening the screw or hexagon nut, the cone pulls Order exampl
into the expansion anchor and tightens against the drilled hole. M6
- Suitable for use in concrete and natural stone. M8
M 10
Yellow zinc
Typical Applications: M 12
plated Steel
Cable trays, handrails, brackets, staircases, ladders, machines, window panels, base plates, scaffoldings and frameworks . Thread (Zn)
Order examp
M6
M8
Technical Data: Materials:
M H A steel
SleeveA4/316
Anchor
Metal Products
Throughbolt, stainless
Recommended loads (non-concreted C 20/25). - zinc plated steel.
- stainless steel [ SS 304 (A2) , SS 316 (A4) ].
M 10
M 12
Type Tension Load Shear Load Bending Moment Screw Grade Fea tur es
(order No) (KN) (KN) (Nm)
Ordert example
Sma ll
M6 2.5 2.3 3.9 8.8
t Torqu
M8 3.3 4.4 17 8.8 Fea tur es t Zinc p
M10 4.7 6.5 34 8.8 t Europea n Technica l Approva l O pti
t Throu
M12 6.9 8.5 60 8.8 t Torque controlled expansion
*for cracked Concrete we shall use 0,5 x this value (approximately) t Applications in damp areas and o
Applicat
t Stainless steel A4/316 steel con
Setting Data:
Edge distance > 1,5 x H eff., distance between anchors > 3 x H eff. t Face xing or through xing
Thickness of foundation > 2 x H eff.
Size H eff. Edge Distance Distance Between Thickness of Washer Tightening Spanner Applications
C (mm) Anchors S (mm) Foundation (Ø) Torque (Nm) size (mm)
(mm)
hmin (mm) fa ca des, ca ble tra ys, ra ilings, steel con
M6 40 60 120 100 12 x 1.6 10 10under-constructions, high-racks, pro
M8 45 68 135 100 16 x 1.6 20 13
M10 55 83 165 110 20 x 2.0 40 17
M12 70 105 210 Type
140 Tension24
load
x 2.5 Shear 75
load 19 moment Tighten torque
Bending Distance between Distance to
(Order No) (kN) (kN) (Nm) (Nm) anchor S (mm) C (mm
Installation
I nsta lla tion
Cable tray Systems
1 2 3 4
Tinst
Drill a hole and clean it with Place the plug and the Tighten the screw. Fixing completed.
a brush, remove dust with a object to fix.
2
blower.
M H A -B Sleeve Anchor with threaded bolt and nut
51
Cable mANAGeMENT sYSTEMS
Cable tray Systems
Typical Applications:
Pipes, ventilation ducts, suspended ceilings, sprinkler systems, brackets, threaded rods and cable trays.
Applications
Setting Data: steel construc
Edge distance > 1.5 x effective anchorage depth, distance between anchors
> 3,0 x effective anchorage depth, min. thickness of foundation > 2,5 x H eff.
52 www.unimetal-ikk.com
1. Internally threaded to take stud or bolt.
M8 30 2. Easy to13 10 action. 32
install by hammer 11 77-120 WA-08
al setting tool Product Information
M10 40 3. Slotted 15 12
sleeve and captive internal42tapered wedge 22 to 77-132 WA-10
s.
ANCHOR
M12
M16
50
65
20 easy
Bolt
facilitate
25
15and
Tension
Sizesetting
20Provides
(kN)
Allows
load
expansion.
DESCRIPTION 52 Shear 38 load 77-141
permanently fixed threaded sockets in concrete.
67 95
bolts or studs to be installed (kN)
and removed without
Bending
SUITABLE
77-150 Concrete
WA-12
moment
FOR
(Nm)WA-16
Stone.
USE IN: Heff.
(mm)
Edge Distance
C (mm)
Distance between
Heavy Duty Anchors
anchor S (mm) (Ø)
Washer Thic
fou
M20 80 35 25damaging the anchor.
82 185 77-162 WA-20
s in concrete and good qualityM 6
stone. 2.6in: zinc plated steel and stainless
Available 3.3 steel grade A4 1. Internally
5.5 threaded to take stud or bolt.
FEATURES 40 60 120 12 x 1.6
services, cable trays, platforms,M drain
8 covers,(1.4401).4.1
suspended ceilings etc. 6.3 setting tool 2. Easy13 to install by hammer action. 50 75 150 16 x 1.6
SS STEEL Install with manual setting tool or mechanical
o be removed or replaced. M 1 0 5.8
for use 8.5
with hammer action drilling machines. 26.5sleeve and captive internal58
3. Slotted tapered wedge to 87 174 20 x 2.0
ANCHOR
MFOR
SUITABLE 1 2 USE IN:HOLE 9.2 HOLE 12
MAXIMUM 46.5 68
facilitate easy setting and expansion.
102 204 24 x 2.5
HREAD
ets in concrete.LENGTH
SIZE M16
THREAD LENGTH
Concrete
(mm)
14
DIAMETERTYPICAL APPLICATIONS
DEPTH
ETAfixing
PENDING
23
RECOMMENDED
TORQUE
PRODUCT 118.5
2007in concreteCODE NEW CODE
80 120 240 30 x 3.0
(mm) (mm) e For permanently
(mm) threaded sockets and good quality stone.
(d)
removed without Stone. (lG ) (Nm)
(l) (do) e Ideal for secure
(ho ) fixing for mechanical services, cable trays, platforms, drain covers, suspended ceilings etc.
M6steel DIAMETER
NGTH 25
HOLE Installation
11
FEATURES
HOLE
MAXIMUM
RECOMMENDED 8 27
(Tinst )
e Securing equipment that may need to be removed or replaced.
Drill aR-DCA
holeWEDGE ANCHORit- with
and clean STAINLESS STEEL Insert the anchor sleeve in
ETA PENDING 2007
Tighten to the recommended Fixing completed.
a brush, remove dust with a THREAD the hole. MAXIMUM
torque.
2
ANCHOR HOLE HOLE
THREAD SIZE LENGTH
THREAD LENGTH THREAD SIZE
DIAMETER DEPTH GRIP TYPE
RECOMMENDED
PRODUCT
SIZE (mm) TORQUE NEW CODE
HOLEblower.
(d) MAXIMUM
MAXIMUM (mm) (mm) (d) (mm) CODE
HOLE
LENGTH HOLE HOLE (d) (l ) G (Nm)
AD
NGTH RECOMMENDED
RECOMMENDED (l) (d ) (h ) o o
(T )
DIAMETER DEPTH PRODUCT M6 SDS-plus
inst
(mm) M6 DIAMETER DEPTH TORQUE
TORQUE
PRODUCT NEW CODE
(mm)(mm) (mm)(mm) M6
CODE
CODE 25 NEW CODE
118 27 4.5 77-608 WA-A4-06
(lG ) (Nm)
M8 (d (d )
o) o (ho(h) o )
(Nm) M8 30 13 10 M8 32 SDS-plus 11 77-620 WA-A4-08
(T(Tinst )
inst ) M10 40 15 12 M10 42 SDS-plus 22 77-632 WA-A4-10
118 M10 8 2727 4.5
4.5 77-108
77-608M12 WA-06
WA-A4-06
50 20 15 52 38 77-641 WA-A4-12 Usable Se
13 M12 10 32 11 77-120
M16 WA-08 25
65 20 M12 67 SDS-plus 95 77-650 WA-A4-16
Plug & drill Ø Length Length dep
10 32 11 77-620 WA-A4-08
M16 SDS-max (mm) (mm) (mm) (
15 M16
12
12
42
42
Manual 22Manual Setting Tool
22
52 Setting Tool
77-132
77-632
WA-10
WA-A4-10 Mechanical Setting Tool
20 M20
15
15
52 38
38 77-141
77-641
WA-12
WA-A4-12
M20 SDS-max 6 50 5
25
20
20
67
67
95
95 77-150
77-650
WA-16
WA-A4-16
6 65 10
35 25 82 185 77-162 WA-20 6 80 25
tainless Steel 6 95 40
Mechanical Setting Tool
for bolt 8 50 5
8 60 10
AD LENGTH
HOLE Use the
HOLEsetting tool to
MAXIMUM
RECOMMENDED 8 80 10
DIAMETER
(mm)
(mm) driveDEPTH
the internal
(mm) wedge PRODUCT
TORQUE
CODE
NEW CODE
8 85 15
(lG ) (Nm)
(do)
into the anchor.(Tinst )
(ho )
8 95 25
118 27
Installation
4.5 77-608
THREAD SIZEWA-A4-06
(d)
GRIP TYPE
8 115 45
13 10 32 11 77-620 WA-A4-08
M6the setting
SDS-plus 10 60 5
ebris
15 and 3. Insert
42 wedge anchor, 4. Use tool to 5. Alternatively use mechanical
12
y clean hole with slotted end
22 77-632
M8 the
drive
WA-A4-10
SDS-plus
internal wedge setting tool with appropriate
10 70 10
20 15 52 38 77-641 WA-A4-12 10 95 15
pump. into the anchor.
M10 SDS-plus drilling machine.
25 20 67 95 77-650 WA-A4-16 10 110 30
M12 SDS-plus
1530 812 857, Fax: +44 (0) 1530 812 862 M16 SDS-max
10 125 45
Mechanical Setting Tool
1. Drill aMechanical
hole of required Setting
2. Remove debris and
M20 Tool 3. Insert wedge anchor,
SDS-max 4. Use the setting tool to 5. Alternatively use mechanical 10 140 60
diameter and depth. thoroughly clean hole with
brush and pump.
slotted end first. drive the internal wedge
into the anchor.
setting tool with appropriate
drilling machine.
10 160 80
10 180 100
34 Technical Advisory Service Tel: +44 (0) 1530 812 857, Fax: +44 (0) 1530 812 862 2007-10-15 14:34:42 12 80 5
12 110 15
12 125 30
12 145 50
Alternatively use the 12 165 70
mechanical setting tool 12 185 90
with an appropriate 16 115 10
drilling machine. 16 130 15
ge anchor, 4. Use the setting tool to 5. Alternatively use mechanical 16 145 30
d drive the internal wedge setting tool with appropriate 16 160 45
into the anchor. drilling machine. 16 180 65
20 160 30 1
812 862
2007-10-15 14:34:42
Manual
d end first. drive the internal wedge setting tool with appropriate
into the anchor. drilling machine.
Mechanical
530 812 862
www.unimetal-ikk.com
Cable tray Systems
53
Cable mANAGeMENT sYSTEMS
Cable tray Systems
Features: SAS
- Suitable for use in concrete, natural stone, brickwork and blockwork
- small distance between achors.
- Optimum performance in most base material types.
- No protruding threads after installation.
- Small distance between anchors and from edge.
- Controlled expansion. M H A Sleeve Anchor
Metal Products
Materials: Applications
Technical Data:
Recommended loads (non-concreted C 20/25). - zinc plated steel. steel constructions, ma chines, pro les, u
- stainless steel [ SS 304 (A2) , SS 316 (A4) ].
Tension Load Shear Load Bending Moment
Bolt Size
(KN) (KN) (Nm)
M6 2.56 2.0 5.0
M8 3.33 3.3 12.5
M10 4.1 5.0 25.5
M12 6.66 7.5 .......
*for cracked Concrete we shall use 0,5 x this value (approximately)
Type Tension load Shear load Bending moment Tighten torque Distance between Distance to edge Min. thickness Spanner
(kN) (kN) (Nm) (Nm) anchor S (mm) C (mm) of found size (SAS)
(Order No)
(hmin) mm
Setting Data: M6 2.0 2.5 4.20 8.0 105 55.0 90.0 10.0
M8
Edge distance > 1.5 x effective 3.0
anchorage 3.3
depth, distance between5.30
anchors 25.0 120 60.0 100.0 13.0
M10 5.0 5.5 12.80 40.0 150 75.0 120.0 17.0
> 3,0 x effective anchorage
M 1 2 depth, min.
7 .5 thickness of8.0
foundation > 2,5
25.0x H eff. 50.0 225 115.0 140.0 ---
M6
Sleeve Anchor - SAS: M6
with hexagon screw (non-cracked concrete C20/25). M8
M8
Usable Length Drilling Depth M10
Size Length Drill (Ø) Hole Ø in Drilling Setting H eff. Min.Usable M10
(mm) (mm) Fixture Depth Depth (mm) Length
(mm) (mm) (Ø) (mm)
Spaner
M6 45 8 10 55 35 35 5 Size M Drill Ø
M6 60 8 10 55 35 35 15
M H A -B Sleeve Anchor with threaded bolt and nut
M8 60 10 12 60 40 40 15 Drillin
HPlug
eff & drill Ø Length
Washer
Dep
M8 80 10 12 60 40 40 25 (mm) (mm) (mm
Setting Depth
8 45
M10 70 12 14 70 50 50 15 55
8 60 55
M10 100 12 14 70 60 50 35 Length 1 0 60 60
*for cracked Concrete we shall use 0,5 x this value (approximately). 10 80 60
12 70 70
12 100 70
54 www.unimetal-ikk.com
Bolt Size Tension load Shear load Bending moment Heff. Edge Distance Distance between Wa
(kN) (kN) (Nm) (mm) C (mm) anchor S (mm) (
Drill a hole and clean it with Insert the sleeve anchor through Tighten to the recommended
MS HSleeve
A -S Sleeve
Anchor
a 2Anchor with hexagon
with hexagon
brush, remove dust with ascrew screw
the fixture into the hole. torque.
Drill Ø mmDrill Ø Lm
enm
gth LeTnhgrtehad DrillinTg
hrd
eeap
dthDrU
ilslianbgledelep
blower. mm mm mm m
M6 M6
Sleeve Anchor - SAB: Plug & drill Ø M 6 M6
Length
U
with threaded bolt and nut M 8 L
(mm) M 8 (mm)
Size Length Drill (Ø) Hole Ø in Min.Drilling Min. Setting Max. Usable Usable Length M8 M8
(mm) (mm) Fixture Depth Depth
H eff.
Length
6 M 1 0 M5100
(mm)
(mm) (mm) (Ø) (mm) 6 M 1 0 M6150
6 80
Drill Ø 6 95
M6 49 8 10 29 27 25 20 Spanner
Size M
M6 64 8 10 29 27 25 35 8 50
M8 60 10 12 34 32 30 25 8 60
M8 75 10 12 34
Washer
H eff 8 80
MB HSleeve
A -B Sleeve
AnchorAnchor with threaded
with threaded bolt
bolt and and 32nut
nut 30 40
Setting8Depth 85
M8 105 10 12 34 32 30 70
8Depth Drilling
95 Drilli
Plug & drill Plug
Ø & Drilling
drill Ø
Length Length Depth Dep
M8 85 10 12 34 32 30 50
(mm) (mm) 8
Length(mm)
1 1 5
(mm) (mm) (mm
M10 73 12 14 44 42 40 25 10 60
8 8 1 04 5 45 75 05 55
M10 88 12 14 44 42 40 40
8 8 1 06 0 60 95 55 55
M10 108 12 14 44 42 40 60 10 1 0 1 06 0 6 0 1 1600 60
M10 138 12 14 44 42 40 90 10 1 0 1 08 0 8 0 1 2650 60
M12 100 16 18 64 62 60 30 12 1 2 1 07 0 7 0 1 4700 70
M12 120 16 18 64 62 60 50
12 1 2 1100 0 1 0 01 6700 70
M16 165 20 22 84 82 80 70 10 180
12 80
12 110
12 125
Installation ( push-through installation ) 12 145
12 165
12 185
1 2 3 4 16 115
16 130
16 145
16 160
16 180
20 160
Place the fixture (object) Remove dust with a blower Tap the anchor through the Tighten to the recommended
and drill a hole. and clean the hole with a fixture with a hammer or a torque.
brush. setting tool.
Size Drilling DrillingUsable UsableSetting Setting Drilling Drilli
Drill Ø Drill ØLength Lengthdepth depthlength length depth min.
depth min. Size Size
Drill Ø Drill ØLength Length
depth dep
(mm) (mm) (mm) (mm)(mm) (mm) (mm)installation
(mm) Installation ( pre-positioned (mm) (mm) )(mm) (mm) (mm)
(mm) (mm) (mm) (mm)(mm) (mm
M68 8 40 40 55 55 5 5 35 35 M6 M68 8 45 45 55 55
M68 8 65 65 55 55 25 25 35 35 M6 M684 8 60 60 55 55
www.unimetal-ikk.com
1 2 3
M810 10 50 50 60 60 5 5 40 40 M8 M810 10 60 60 60 60
M810 10 75 75 60 60 30 30 40 40 M8 M810 10 80 80 60 60
Cable tray Systems
55
Cable mANAGeMENT sYSTEMS
Cable tray Systems
Features: STB
- Suitable for use in cracked concrete or in non-cracked concrete and in natural stone.
- Special design of the clip in stainless steel which ensures a safe hold in the hole.
- Torque controlled expansion.
- Zinc plated > 5µm.
- User friendly, face fixing or through fixing.
Throughbolt, stainless
Throughbolt, steel A4/316
stainless steel A4/316
Typical Applications:
Fea tur es Fea tur es
Uni - channel, hand rails, steel constructions, cable trays, supports, brackets, ducts and shelf
t feet.
Europea nt TeEch
un
roicpaelaAnpTpercohvnailcO
a lpAtipopnro
7v
t Torque controlled
t Torqueexpansion
controlled expansi
t Applications in damp areas
t Applications and outdo
in damp area
Materials: t Stainless steel A4/316steel A4/316
t Stainless
t Face xingt or through
Face xing
xing or through xin
- zinc plated steel.
- stainless steel [ SS 304 (A2) , SS 316 (A4) ].
ApplicationsApplications
fa ca des, ca bflaectaradyess,, rcaailbinlegst,rasytese, lraco
ilinnsgtrsu, cs
under-constructions,
under-constructions,high-racks, pro high-ra les
Through bolt
Tension Thickness
Washer o
Bolt Size Boltload
Size Shearload
Tension load Bending momentBendingHeff.
Shear load moment Edge Distance
Heff. Distance betweenDistance
Edge Distance Washer
between
foundation
(kN) (kN)
(kN) (Nm)
(kN) (mm)
(Nm) C (mm)
(mm) anchor S (mm)
C (mm) anchor (Ø)
S (mm) (Ø)
(mm)
M6 2.6
M6 3.3
2.6 5.5
3.3 40
5.5 406 0 6102 0 12
1 2x01.6 12 1x 01.6
0
Technical Data: M8 4.1
M8
5.8
6.3
4.1
8.5
13
6.3
26.5
50
13
58 Usable Length
507 5 7155 0 16
1 5x01.6
20
16 1x 01.6
0
M10 M10 5.8 8.5 26.5 588 7 8177 4
Drilling Depth 1 7x42.0 20 1x 22.0
0
Through bolt zinc plated (non-cracked C20/25).
M12 9.2
M12 12
9.2 46.5
12 68
46.5 102
68 120024 24
2 0x42.5 24 1x 42.5
0
M16 14
M16 1423 118.5
23 80
118.5 120
80 122400 30
2 4x03.0 30 1x 63.0
0
Bolt Tension Load Shear Load Bending Moment
M H A Sleeve Anchor
Metal Products
Installation Parameters:
Throughbolt,
Throughbolt, stainless
stainless
Throughbolt, steel
steel A4/316
A4/316
stainless steel A4/316
Through bolt zinc plated, stainless steel or hot-dip galvanized.
Bolt Size Bolt Length Drill Ø Hole Ø in Drilling Depth Setting Depth H eff. Usable Length
(mm) (mm) Fixture (mm) (mm) (mm) (mm) Fix (mm)
40 6 6.5 35 27 .....
Fea turF3eesa tur esFea tur es
M6
55 6 6.5 35 35 35
t Eurt15opeEaunroTpetecahnnEiu
TceraoclphAenpaicpnarlo
TA
evacphlpnO
riocpvatailolAn
70 6 6.5 35 35 35
t Torque
t Torque30
t controlled
controlled Torque expansion expansion
controlled ex
95 6 6.5 35 35 35 55
50 8 9 35 35 .....
t10 Applications
t Applications t inApplications
damp in damp areas in areas
and damp ou a
65 8 9 40 40 ..... t20 Stainless
t Stainless steel steel A4/316
A4/316
t Stainless steel A4/31
M8 80 8 9 40 40 40 t Facet35 Face
xing or txing
through
Face or throughxingxing or througxing
95 8 9 40 40 40 50
105 8 9 40 40 40
Applications
60
Applications Applications
65 10 11 40 40 40 15
80 10 11 50 50 50
fa ca def20as,ccaadbelse, fctaracbyalsd
e, ertarsa,ilycinsag
,brsla,eisltirenaegylss,c, sortan
eseilt
M10 95 10 11 50 50 50 under-constructions,
under-constructions,
35 under-constructions, high-racks, high-racks prohi
115 10 11 50 50 50 55
120 10 11 50 50 50 60
80 12 13 65 50 50 20
100 12 13 65 60 60 30
M12
120 12 13 65 60 60 50
135 12 13 65 60 60 65
Size Tension
Bolt SizeBoltTension load Sizeload
Bolt105 Shear
16
Tension Shear
load load
load Bending Bending
moment
18Shear moment
load 85 70 Heff. Edge70
Heff. moment
Bending Edge Distance
Distance
Heff. 15 EdgeDistance
Distance Distancebetween
between Washer
Distance WasherThickne
between Wa
(kN)
(kN) 140 (kN)
(kN)
16
(kN) (Nm) (Nm)
18 (mm)
(kN) (mm)
85 C (mm) C (mm)anchor Sanchor
(Nm)
80 (mm) S (mm) (Ø)
80 (mm) (Ø) founda
40 C (mm) anchor S (mm) (mm
M16
M6 M 6 2.6 M180 62.6 3.3
16
2.6 3.3 18 5.53.3 5.5
85 405.58040 806 0
40 6 0 80 1 2 06 0 120 2 012 x 1.6
12 x11.6 112
00
M8 M 8 4.1 M220 84.1 6.3
4.1
16 6.3 18 136.3 13
85 501380 50 807 5
50 7 5 120 1 5 07 5 150 5 016 x 1.6
16 x11.6 116
00
M 1 0 M 1 0 5.8 M 15.8 0 8.5
5.8 8.5 26.58.5 26.5 5826.5 58 8 758 87 1 7 48 7 174 7 420 x 2.0
20 x12.0 120
20
M 1Effective
M 1 2H eff.= M 19.2
2 9.2 anchorage
2 depth12
9.2 12 46.512 46.5 6846.5 68 1 068
2 102 2 0140 2 204 0 424 x 2.5
24 x22.5 124
40
M 1 6 M 1 6 14 M 1 14 6 2314 23 118.5
23 118.5 118.5 80
80 1 280
0 120 2 4102 0 240 4 030 x 3.0
30 x23.0 130
60
Installation
sta llIantsio
tanlla tiIonnsta lla tion 3
1 2
drill Ø Length
Length Length
depth m
(mm) (mm) (mm)(mm) (mm) (mm) (mm) (mm) (mm
Cable tray Systems
6 6 50 6 50 5 50 5 30
6 6 65 6 65 1 0 6 51 0 4 0
6 6 80 6 80 2 5 8 02 5 4 0
6 6 95 6 95 4 0 9 54 0 4 0
8 8 50 8 50 5 50 5 27
8 8 60 8 60 1 0 6 01 0 3 0
8 8 80 8 80 1 0 8 01 0 5 0
8 8 85 8 85 1 5 8 51 5 5 0
8 8 95 8 95 2 5 9 52 5 5 0
8 8 1 1 5 81 1 5 4 5 1 1 54 5 575 0
10 1 0 6 0 1 06 0 5 60 5 33
10 1 0 7 0 1 07 0 1 0 7 01 0 3 5
Cable mANAGeMENT sYSTEMS
Cable tray Systems
Features:
- Assembly detachable, multiple removing and fixing. SSA
- Low energy impact, power-saving assembly.
- Force controlled expansion.
- Flexibility inside threaded anchor.
- Variable length and art of threaded rods or bolts.
- By tightening the screw, the cone pulls into the sleeve and tense against the drill hole.
- Small edge distance and small distance between anchor.
- Expansion elements are held together by a spring.
- Optimum taper nut angle for maximum expansion.
- Pressed steel segment ensures consistent dimensional accuracy.
- Provide a projecting stud to support fixture during installation and removal.
- Suitable for use in concrete, natural stone, Brick and sand stone.
Typical Applications:
For fixing : steel constructions, handrails, consoles, brackets, ladders, gates and spacing designs.
Materials:
- zinc plated and die-cast.
M H A Sleeve
KN
Anchor
N.m N.m
Metal Products
KN KN Drill
Ø
M6 3.3 2.1 1.6 6.5 5.0
M8 4.8 4.4 2.1 15.0 7.5 Fea tur es
M10 6.2 6.1 2.6 27.0 13.0 t Sma ll edge
M12 9.7 12.4 3.9 50.0 23.0 Drilling Depth t Torque con
(Hole Depth)
*for cracked Concrete we shall use 0,5 x this value (approximately) Bolt Length
t Zinc plated
t Through x
Type Tension load Shear load Bending moment Tighten torque Distance between Distance to edge
(Order No) (kN) (kN) (Nm) (Nm) anchor S (mm) C (mm)
58 www.unimetal-ikk.com
Throughbolt, stainless steel A4/316
Heavy Duty Anchors
Fea tur es
t Europea n Technica l Approva l O pt
t Torque controlled expansion
t Applications in damp areas and o
t Stainless steel A4/316
Installation
t Face xing or through xing
Installation Parmeters:
A- Using a hexagon screw: insert shield only, place the fixture over the hole and insert a hexagon screw with
Applications
a washer through the fixture.
fa ca des, ca ble tra ys, ra ilings, steel co
B- Using a threaded bolt and nut: insert the shield with a threaded bolt, position the fixture over the thread and
under-constructions, high-racks, pr
add a washer with a nut.
170 75
10 160 80
I nsta lla tion 1 0 1 8 0 1 00
Cable tray Systems
11 2 3 4
12 80 5
12 110 15
12 125 30
12 145 50
1 2Tinst 165 70
12 185 90
Drill a hole and clean it with Place the plug and the Tighten the screw. 1 6 Fixing completed.
115 10
a brush, remove dust with object to fix. 16 130 15
2
a blower. 16 145 30
16 160 45
16 180 65 59
20 160 30
Usable Se1
Cable mANAGeMENT sYSTEMS
Cable tray Systems
60 www.unimetal-ikk.com
- Ordering Cable Tray
Side Height Varieties
Cable trays are available in the following side heights:
• 25 mm • 50 mm • 75 mm • 100 mm
* Other side heights can be manufactured upon request.
Cable trays and accessories are available in the following side height types:
- Straight end - Return flange inside
STR RFI
- C - Type outside
CTO
-Abbreviations
Materials & Finishes Code Thickness Code
Stainless Steel SS Sheet of 1.0 mm 1
www.unimetal-ikk.com
Sheet of 2.0 mm 4
Hot-dip Galvanized HD Sheet of 5.0 mm 5
Electrolytic Galvanized EG
Powder Coated PC
For more information on ordering and types, Uni-Metal technical staff are ready to assist you with all necessary details.
www.unimetal-ikk.com
61
Cable mANAGeMENT sYSTEMS
Cable tray Systems
Order Example
PC
Item Side Width Thickness Side Length Pre. Galvanized Powder Coated
Number Height (mm) (mm) Type (mm) (Materials) (Finishes)
Examples:
1- Order number for Hot-Dip Galvanized 2,400 mm length cable tray, 50 mm side
height, 2mm sheet thickness and 500 mm width with outside return flange:
130 050 0500 4/RFO 2400 PG PC
N.B.: Order number for connectors will include the item number, side height and thickness of the sheet
-General Information
Consideration shall be given to the following factors when undertaking the design of a cable tray run and a support
system, although some of these (ex: wind loads) may not be relevant to every installation :
• Distributed loads e.g. cables, pipes. • Spacing of supports
• Point loads • Safety factor
• Thermal expansion & contraction • Deflection
• Wind & external forces
-Location of Couplers
In practice, it is often difficult to pre-determine where the couplers
will be located within a straight run of a cable tray.
However, it is worth making some efforts to roughly plan their
position during the early stages of installation. The worst positions S/4
62 www.unimetal-ikk.com
Cable tray Systems
Notes
63
www.unimetal-ikk.com
Cable mANAGeMENT sYSTEMS
Cable tray Systems
Notes
64 www.unimetal-ikk.com