Professional Documents
Culture Documents
Universal Standard Ground Sense Op-Amp.: LM358 Family, LM324 Family, LM2904 Family, LM2902 Family
Universal Standard Ground Sense Op-Amp.: LM358 Family, LM324 Family, LM2904 Family, LM2902 Family
TROPHY SERIES
Universal Standard
Ground Sense Op-Amp.
LM358 family, LM324 family, LM2904 family, LM2902 family
ͶDescription
TROPHY
The Universal Standard family LM358/324
SERIES
and LM2904/2902 monolithic ICs integrate two
independent op-amp circuits and phase
compensation capacitors on a single chip, feature Dual Quad
high gain and low power consumption, and
LM358 family LM2904 family LM324 familyͳ LM2902 familyͳ
possess an operating voltage range between LM358DR LM2904DR LM324DR LM2902DR
LM358PWR LM2904PWR LM324PWR LM2902PWR
3[V]and 32[V] (single power supply.) LM358DGKR LM2904DGKR LM324KDR LM2902KDR
LM2904VQDR LM2902KPWR
LM2904VQPWR LM2902KVQDR
LM2902KVQPWR
ڏUnder development
ͶCharacteristics
1) Operating temperature range 3) Low supply current
Commercial Grade 4) Common-mode input voltage range, including ground
LM358/324 family: 0[ͨ] to +70[ͨ] 5) Differential input voltage range equal to maximum rated
Extended Industrial Grade supply voltage! ! ! ! ! ! ! ! !
LM2904/2902 family: -40[ͨ] to +125[ͨ] 6) High large signal voltage gain
7) Wide output voltage range
2) Wide operating voltage range
+3[V] to +32[V] (single supply)
! ! ! ! ! ! ! ! !
͘1.5[V] to ͘16[V] (dual supply) ! ! ! ! ! ! ! !
ͶPin Assignment
1OUT 1 14 4OUT
1OUT 1 8 Vcc 1IN- 2 13 4IN-
㧙ޓ㧗 㧗ޓ㧙
1IN+ 3 12 4IN+
1IN- 2 㧙ޓ㧗 7 2OUT
Vcc 4 11 GND
ͳUnder development
Supply Voltage
Vcc-GND +32 +26 +32 V
ͳUnder development
ͶElectric Characteristics
! ͵LM358,LM324 family (Unless otherwise specified, Vcc=+5[V])
Limit
Temperature
Parameter Symbol LM358 family LM324 familyͳ Unit Condition Fig.No
range
Min. Typ. Max. Min. Typ. Max.
Input Offset 25ͨ 㧙 3 7 㧙 3 7 VO=1.4[V]
Voltage (*1) VIO mV VIC=VICR(min) 2
Full range 㧙 㧙 9 㧙 㧙 9 Vcc=5[V] to 30[V]
Input Offset
ĮVIO 㧙 㧙 7 㧙 㧙 㧙 㧙 ԜV/ͨ 㧙 㧙
Voltage Drift
Input Offset 25ͨ 㧙 2 50 㧙 2 50
Current (*1) IIO nA VO=1.4[V] 2
Full range 㧙 㧙 150 㧙 㧙 150
Input Offset
ĮIIO 㧙 㧙 10 㧙 㧙 㧙 㧙 pA/ͨ 㧙 㧙
Current Drift
Input Bias 25ͨ 㧙 20 250 㧙 20 250
Current (*1) IIB nA VO=1.4[V] 2
Full range 㧙 㧙 500 㧙 㧙 500
Input Common-mode 25ͨ 0 㧙 Vcc-1.5 㧙 㧙 Vcc-1.5
Voltage Range VICR V Vcc=5[V] to 30[V] 2
Full range 0 㧙 Vcc-2.0 㧙 㧙 Vcc-2.0
High Level 25ͨ Vcc-1.5 㧙 㧙 Vcc-1.5 㧙 㧙 RL͠2[kȍ]
Output Voltage VOH V 3
Full range 27 28 㧙 27 28 㧙 Vcc=30[V],RL͠10[kȍ]
Low Level
VOL Full range 㧙 5 20 㧙 5 20 mV RL͟10[kȍ] 2
Output Voltage
Large Signal Vcc=15[V]
Voltage Gain VO=1[V] to 11[V] 2
AVD 25ͨ 25 100 㧙 25 100 㧙 V/mV
RL͠2[kȍ]
Common-mode
Rejection Ratio Vcc=5[V] to 30[V],
CMRR 25ͨ 65 80 㧙 65 80 㧙 dB 2
VIC=VICR(min)
Supply-Voltage
KSVR 25ͨ 65 100 㧙 65 100 㧙 dB Vcc=5[V] to 30[V] 2
rejection ratio
Cross-talk
VO1/VO2 25ͨ 㧙 120 㧙 㧙 120 㧙 dB f=1[kHz] to 20[kHz] 5
Attenuation
Output Current (*2) 25ͨ 20 30 㧙 20 30 㧙 Vcc=15[V],VO=0[V]
Source mA
Full range 10 㧙 㧙 10 㧙 㧙 VID=1[V]
25ͨ 10 20 㧙 10 20 㧙 Vcc=15[V],VO=0[V] 3
mA
Sink Full range 2 㧙 㧙 2 㧙 㧙 VID=-1[V]
25ͨ 12 30 㧙 12 30 㧙 ԜA VO=200[mV],VID=-1[V]
Supply Current Full range 㧙 0.7 1.2 㧙 0.7 1.2 VO=2.5[V],No Load
(All Amps) ICC mA 3
Vcc=30[V],VO=0.5[V]
Full range 㧙 1 2 㧙 1.4 3
No Load
Slew Rate at RL=1[Mȍ],CL=30[pF]
Unity-Gain VI=͘10[V]
SR 25ͨ 㧙 0.3 㧙 㧙 0.5 㧙 V/Ԝs 3
Vcc=15[V],GND=-15[V]
(reference to Fig1)
Unity Gain RL=1[Mȍ],CL=20[pF]
Bandwidth B1 25ͨ 㧙 0.7 㧙 㧙 1.2 㧙 MHz Vcc=15[V],GND=-15[V] 3
(reference to Fig1)
Equivalent Vcc=15[V],GND=-15[V]
Input Noise Vn 25ͨ 㧙 40 㧙 㧙 35 㧙 P8 *\ RS=100[ȍ],VI=0[V] 3
Voltage f=1[kHz](reference to Fig2)
(*1) Absolute value! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ͳUnder development
(*2) Under high temperature, consider the power dissipation of IC when selecting the output current.
When the output terminal is continuously shorted, the output current reduces the temperature inside the IC by flushing.
2/8
These Products are designed and produced by ROHM.
TROPHY SERIES LM2904/2902/358/324 family
͵LM2904,LM2902 family (Unless otherwise specified, Vcc=+5[V])
Limit
Temperature
Parameter Symbol LM2904 family LM2902 familyͳ Unit Condition Fig.No
range
Min. Typ. Max. Min. Typ. Max.
Input Offset 25ͨ 㧙 3 7 㧙 3 7
Voltage (*3) VO=1.4[V],VIC=VICR(min)
VIO mV 2
Full range 㧙 㧙 10 㧙 㧙 10 Vcc=5[V] to MAX(*8)
Input Offset
ĮVIO 㧙 㧙 7 㧙 㧙 7 㧙 ԜV/ͨ 㧙 㧙
Voltage Drift
Input Offset LM2904 25ͨ 㧙 2 50 㧙 2 50
Current (*3) LM2902
(*5) Full range 㧙 㧙 300 㧙 㧙 300
IIO nA VO=1.4[V] 2
LM2904V 25ͨ 㧙 2 50 㧙 2 50
LM2902V
(*5) Full range 㧙 㧙 150 㧙 㧙 150
Input Offset
ĮIIO 㧙 㧙 10 㧙 㧙 10 㧙 pA/ͨ 㧙 㧙
Current Drift
Input Bias Current (*3) 25ͨ 㧙 20 250 㧙 20 250
IIB nA VO=1.4[V] 2
Full range 㧙 㧙 500 㧙 㧙 500
Input Common-mode 25ͨ 㧙 㧙 Vcc-1.5 㧙 㧙 Vcc-1.5
Voltage Range VICR V Vcc=5[V] to MAX(*8) 2
Full range 㧙 㧙 Vcc-2.0 㧙 㧙 Vcc-2.0
High Level
25ͨ Vcc-1.5 㧙 㧙 Vcc-1.5 㧙 㧙 RL͠10[kȍ]
Output Voltage
LM2904
LM2902 Full range 23 24 㧙 23 24 㧙 Vcc=MAX(*8),RL͠10[kȍ]
VOH V 3
(*5)
LM2904V
LM2902V Full range 27 28 㧙 27 㧙 㧙 Vcc=MAX(*8),RL͠10[kȍ]
(*5)
Low Level
VOL Full range 㧙 5 20 㧙 5 20 mV RL͟10[kȍ] 3
Output Voltage
Large Signal
Voltage Gain Vcc=15[V],VO=1[V] to 11[V]
AVD 25ͨ 25 100 㧙 25 100 㧙 V/mV 2
RL͠2[kȍ]
Common- LM2904
mode LM2902 25ͨ 50 80 㧙 50 80 㧙 dB
Rejection (*5) Vcc=5[V] to MAX(*8)
CMRR 2
Ratio LM2904V VIC=VICR(min)
LM2902V 25ͨ 65 80 㧙 60 80 㧙 dB
(*5)
Supply LM2904
Voltage LM2904V
65 100 㧙 50 100 㧙
Rejection M2902
KSVR 25ͨ dB Vcc=5[V] to MAX(*8) 2
Ratio (*5)
LM2902V
㧙 㧙 㧙 60 100 㧙
(*5)
Cross-talk Attenuation VO1/VO2 25ͨ 㧙 120 㧙 㧙 120 㧙 dB f=1[kHz] to 20[kHz] 5
Output Current (*4) 25ͨ 20 30 㧙 20 30 60 Vcc=15[V],VO=0[V]
Source mA
Full range 10 㧙 㧙 10 㧙 㧙 VID=1[V]
25ͨ 10 20 㧙 10 20 㧙 Vcc=15[V],VO=0[V]
Sink mA
Full range 2 㧙 㧙 2 㧙 㧙 VID=-1[V]
3
LM2904
LM2902 25ͨ 㧙 30 㧙 㧙 30 㧙 ԜA
(*5)
Io VO=200[mV],VID=-1[V]
LM2904V
LM2902V 25ͨ 12 40 㧙 12 40 㧙 ԜA
(*5)
Supply Current Full range 㧙 0.7 1.2 㧙 0.7 1.2 VO=2.5[V],No Load
(All Amps) ICC mA 3
Vcc=MAX(*8),VO=0.5[V]
Full range 㧙 1 2 㧙 1.4 3
No Load
Slew Rate at RL=1[Mȍ],CL=30[pF],
Unity Gain VI=͘10[V]
SR 25ͨ 㧙 0.3 㧙 㧙 0.5 㧙 V/Ԝs 3
Vcc=15[V],GND=-15[V]
(reference to Fig1)
Unity-Gain Bandwidth RL=1[Mȍ],CL=20[pF]
B1 25ͨ 㧙 0.7 㧙 㧙 1.2 㧙 MHz Vcc=15[V],GND=-15[V] 3
(reference to Fig1)
Equivalent Input Noise Vcc=15[V],GND=-15[V]
Voltage RS=100[ȍ]VI=0[V]
Vn 25ͨ 㧙 40 㧙 㧙 35 㧙 P8 *\ 3
f=1[kHz],
( reference to Fig2)
(*3) Absolute value! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ͳUnder development
(*4) Under high temperature, consider the power dissipation of the IC when selecting the output current.
When the output terminal is continuously shorted the output current is reduced to lower the temperature inside the IC.
(*5) The maximum supply voltage is 26V for the LM2904DR, LM2904PW, LM2904PWR, and LM2904DQKR
The maximum supply voltage is 32V for the LM2904VQDR and LM2904VQPWR
3/8
These Products are designed and produced by ROHM.
TROPHY SERIES LM2904/2902/358/324 family
ͶCircuit Diagram
8EE
+0
176
+0
)0&
Fig.1 Circuit Diagram (each Op-Amp)
͗Calculation͗
1.Input Offset Voltage (VIO)
VF1
Vio [V]
1+ Rf /Rs
VF2 - VF1
Iio [A]
Ri (1+ Rf / Rs) Rf
50[kȍ]
3.Input Bias Current (IIB) 500[kȍ] 0.1[μF]
S1 VOUT EK
VF4 - VF3 Vcc
Ib [A] +15[V]
2× Ri (1+ Rf / Rs) Rs Ri
Rs Ri S3
10× (1+ Rf /Rs) 1000[pF]
AV 20× Log [dB]
VF6 - VF5 S2 GND V VF
RL
-15[V]
Rf 50[kȍ]
5.Common-mode rejection ratio (CMRR)
ٌVcc×(1+Rf /Rs)
PSRR 㧩20×Log [dB]
VF10 - VF9
ٌVcc=25V
4/8
These Products are designed and produced by ROHM.
TROPHY SERIES LM2904/2902/358/324 family
ͶMeasurement Circuit 2: Switch Condition
SW No. SW SW SW SW SW SW SW SW SW SW SW SW SW SW SW
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
Supply Current
OFF OFF OFF ON OFF OFF ON OFF OFF OFF OFF OFF OFF OFF OFF
Input voltage
3[V]
SW4
SW5 R2
SW6 R3
Vcc
0.5[V]
A
t
Input waveform
㧙
Output voltage
㧗 SR 㧩 ǻV / ǻt
SW1 SW2 SW3
SW10 SW11 SW12 SW13 SW14 SW15 3[V]
SW7 SW8 SW9
RS R1
GND
A ǻV
㨪 㨪 RL CL V V
VIN- VIN+ 㨪 VOUT ǻt
0.5[V]
t
Output waveform
Fig.3 Measurement Circuit 2 (each Op-Amp) Fig.4 Slew Rate Input Waveform
R2=100[kȍ]
R2=100[kȍ]
Vcc=+2.5[V]
Vcc=+2.5[V]
R1=1[kȍ]
R1=1[kȍ]
CH1 other
CH
VIN
R1//R2 V VOUT1
GND=-2.5[V] =0.5 [Vrms] R1//R2 V VOUT2
GND=-2.5[V]
100×VOUT1
VO1/VO2=20×log VOUT2
5/8
These Products are designed and produced by ROHM.
TROPHY SERIES LM2904/2902/358/324 family
ͶDescription of Electrical Characteristics
Described below are descriptions of the relevant electrical terms
Please note that item names, symbols and their meaning may differ form those on another manufacturer’s documents.
1.4 Operating temperature range and storage temperature range (Topr, Tstg)
The operating temperature range indicates the temperature range within which the IC can operate. The higher the ambient temperature, the lower the power
consumption of the IC. The storage temperature range denotes the range of temperatures the IC can be stored under without causing excessive
deterioration of the electrical characteristics.
2. Electric characteristics
6/8
These Products are designed and produced by ROHM.
TROPHY SERIES LM2904/2902/358/324 family
ͶDerating Curves
1000 1000
500[mV] TSSOP8 (*6) 500[mV] TSSOP8 (*6)
600 600
400 400
200 200
125[ͨ]
70[ ͨ]
Power Dissipation
Package Pd[W] Ԙja [ͨ/W]
Ͷ Precautions
1) Unused circuits
When there are unused circuits, it is recommended that they be connected as
in Figure 7, setting the non-inverting input terminal to a potential within the Vcc
in-phase input voltage range (VICR).
Please note that the circuit operates normally only when the input voltage is
within the common mode input voltage range of the electric characteristics.
GND
3) Power supply (single / dual)
The op-amp operates when the voltage is applied between Vcc and GND.
Fig.7 Disable circuit example
Therefore, the single supply op-amp can be used as a dual supply op-amp as well.
7) Radiation
This IC is not designed to withstand radiation.
8) IC handing
Applying mechanical stress to the IC by deflecting or bending the board may cause fluctuation of the electrical characteristics due to piezoelectric (piezo)
effects.
9) IC operation
The output stage of the IC is configured using Class C push-pull circuits. Therefore, when the load resistor is connected to the middle potential of Vcc and
GND, crossover distortion occurs at the changeover between discharging and charging of the output current. Connecting a resistor between the output
terminal and GND and increasing the bias current for Class A operation will suppress crossover distortion.
7/8
These Products are designed and produced by ROHM.
TROPHY SERIES LM2904/2902/358/324 family
ͶDimensions
SOIC8 TSSOP8 MSOP/VSSOP8
TSSOP14
SOIC8
SOIC14 TSSOP14
1234
1234
1234
1234
1234
1234
1234
8/8
These Products are designed and produced by ROHM.