Professional Documents
Culture Documents
Usage
These steel grades are characterised by a minimum yield strength of 235 - 355 MPa and by good weldability. These grades are used above all for
manufacturing boilers, pressure vessels and pipes transporting hot liquids. The user of these steel grades must make sure that his calculation, design and
processing methods are appropriate for the material. The grades of this series offer good cold and hot-forming properties.
Standards
Europe Material no. D F I GB E USA J FK1)
EN 10028-2 DIN 17155 NFA 36-205, 36-206 UNI 5869 BS 1501 UNE 36087 ASTM JIS G 3115
P235GH 1.0345 HI A 37 CP FE 360 - 1KW 161 Gr. 360 A 37 RCI A 285 Gr. C-A SPV 24 A
164 Gr. 360 414 Gr. C
A 516 Gr. 55
P265GH 1.0425 HII A 42 CP Fe 410 - 1KW 161 Gr. 400 A 42 RCI A 414 Gr. E - A
164 Gr. 400 A 516 Gr. 60
224 Gr. 400
P295GH 1.0481 17 Mn 4 A 48 CP Fe 460 - 1KW 224 Gr. 490 A 47 RCI A 414 Gr. F SPV 32 B
A 516 Gr. 65
P355GH 1.0473 19 Mn 6 A 52 CP Fe 510 - 1KW - A 52 RCI A 414 Gr. G SPV 36 B
16Mo3 1.5415 15 Mo 3 15 D3 16 Mo 3 243 B 16 Mo 3 A 204 Gr. B - B
13CrMo4-5 1.7335 13 CrMo 4 4 15 CD 4.05 14 CrMo 4 5 620 Gr. 27 14 CrMo 4 5 A 387 Gr. 12 - B
1)
FK = Tensile strength class
Chemical composition in percent by weight [%] (Heat analysis)
Grade C Si Mn P S N Altotal Cu1) Cr Ni Mo Ti V Nb
max. max. max. max. min. max. max. max. max. max.
P235GH5) max. 0,16 0,35 0,602) - 1,20 0,025 0,015 0,0123) ≥ 0,020 0,30 max. 0,30 0,30 max. 0,08 0,03 0,02 0,020
P265GH5) max. 0,20 0,40 0,802) - 1,40 0,025 0,015 0,0123) ≥ 0,020 0,30 max. 0,30 0,30 max. 0,08 0,03 0,02 0,020
P295GH5) 0,08 - 0,20 0,40 0,902) - 1,50 0,025 0,015 0,0123) ≥ 0,020 0,30 max. 0,30 0,30 max. 0,08 0,03 0,02 0,020
P355GH5) 0,10 - 0,22 0,60 1,10 - 1,70 0,025 0,015 0,0123) ≥ 0,020 0,30 max. 0,30 0,30 max. 0,08 0,03 0,02 0,020
6)
16Mo3 0,12 - 0,20 0,35 0,40 - 0,90 0,025 0,010 0,012 0,30 max. 0,30 0,30 0,25 - 0,35 - - -
6)
13CrMo4-5 0,08 - 0,18 0,35 0,40 - 1,00 0,025 0,010 0,012 0,30 0,704) - 1,15 - 0,40 - 0,60 - - -
1)
A lower Cu-content and a maximum tin content may be agreed in the order, e. g. with respect to formability.
2)
For thicknesses < 6,0 mm, a minimum content for Mn that is 0,20 % smaller than specified is permitted.
3)
Al / N ≥ 2
4)
If resistance against high-pressure hydrogen is important, a minimum percentage by mass of Cr of 0,80 %
may be agreed in the order.
5)
Cr + Cu + Mo + Ni ≤ 0,70%
6)
The al-content of the melting is to determine and to indicate in the certification
Mechanical properties1)
GradeMin. yield strength Tensile strength Min. total elongation [%]
MPa MPa LO = 5,65 √SO
2) 2)
e ≤ 16 e > 16
P235GH 235 225 360 - 480 24
P265GH 265 255 410 - 530 22
P295GH 295 290 460 - 580 21
P355GH 355 345 510 - 650 20
16Mo3 275 270 440 - 590 22
13CrMo4-5 300 290 450 - 600 19
1)
Transverse samples
2)
Nominal thickness e [mm]
Grade Yield point at elevated temperature Rp0,2 [MPa] at a test temperature von [°C]
300 350 400 450 500
e ≤ 16 e > 16 e ≤ 16 e > 16 e ≤ 16 e > 16 e ≤ 16 e > 16 e1) ≤ 16 e1) > 16
1) 1) 1) 1) 1) 1) 1) 1)
1)
Nominal thickness e [mm]
1)
Average values of 3 samples; one individual value may fall short of the required minimum value by not
more than 30 %. The sample width shall equal the product thickness if the latter is between
6 and 10 mm, the tests being performed using samples which are similar to Charpy-V samples.
The values specified in the table above are to be reduced proportionally to the sample width.
Welding
The steel grades of this series may be welded by means of the usual welding techniques.
Genel amaçlı ve inşaat, yapı sektöründe kullanılan çeliklerdir. İşleme yapmak için karbon oranı çok düşürülmüş çeliklerdir.
Soğuk şekillendirmenin her tipine uygun çok düşük karbon içeren çeliklerdir.
KALİTE A % min r n
Rp 02 (N/mm2) max Rm (N/mm2)
Lo = 80 mm min min
DC 01 280 270 ÷ 410 28 - -
SOĞUK ŞEKİLLENDİRME İÇİN SICAK DALDIRMA GALVANİZ ÇİNKO KAPLANMIŞ, DÜŞÜK KARBONLU ÇELİKLER (EN-10142-90+A1-95)
YAPISAL KULLANIM VE SOĞUK ŞEKİLLENDİRME İÇİN ALÜMİNYUM ALAŞIMLI SICAK DALDIRMA DÜŞÜK KARBONLU ÇELİKLER (EN 10154-96)
DC 03 ED
Kontrol edilmiş kimyasal bir karışımdan ibaret olan bu çelikler dekape (çözünürlülük) fazı esnasında içeriğinde ağırlık kaybına neden olur. Özellikle karbon oranının (0.040 %
max) oldukça düşürülmesi garanti altına alınır ve içeriğinde daha fazla manganez, kükürt, fosfor ve bakırın sürekliliği sağlanır.Bunun sonucunda çizilme direnci ve direkt emaye
yapmaya uygun garanti sağlanıyor.
DC 04 ED
Toz elektrostatik emaye kaplamaya uygun parçalarla derin presleme yapmak için karbon oranı çok düşürülmüş çeliklerdir.
BÜKME, KIVIRMA VE SOĞUK ŞEKİLLENDİRME İÇİN YÜKSEK MUKAVEMETLİ ÇELİKLER (EN 10149-92)
Yüksek mukavemetli çelikler, Soğuk olarak derin çekme, bükme, sıvama ve şekillendirme operasyonlarında kullanılır. İnce tane büyüklüğünde çelik yapısına sahip, düşük kükürt
içeriği olan değişik mukavemet derecelerinde mineral içeriğien sahiptir. Aşağıda gösterilen 5 farklı kalite birbirlerinden farklı değerler gösterirler.
KALİTE C % max Mn % max Si % max P % max S % max Al % min Nb % max V % max Ti % max
S315 MC (1) 0,12 1,3 0,5 0,025 0,02 0,015 0,09 0,2 0,15
S355 MC (2) 0,12 1,5 0,5 0,025 0,02 0,015 0,09 0,2 0,15
S420 MC (3) 0,12 1,6 0,5 0,025 0,02 0,015 0,09 0,2 0,15
S460 MC 0,12 1,6 0,5 0,025 0,02 0,015 0,09 0,2 0,15
S500 MC 0,12 1,7 0,5 0,025 0,02 0,015 0,09 0,2 0,15
KIVRILMA alfa =
180° D Temp. °C J min
Germany İtaly UK
STANDART SEMBOL France NFA Spain UNE USA ASTM Japan JIS
DIN UNI BS
EN 10111 NFA36-301 DIN 1614 UNI 5867 BS 1449 UNE 36-086/ll ASTM-SAE JIS G3131
EN 10025 NFA35-501 DIN 17100 UNI 7070 BS 4360 UNE 36080 ASTM JIS 3101
EN 10207
SPH235 A37AP/E24.4P HI
SPH265 A42AP/E28.4P HII
4. Kazanlar İçin Çelikler
EN 10028-2 NFA36-205 DIN 17155 UNI5869 BS 1501 UNE 36087 ASTM JISG3115
5. Basınçlı Kaplar için Çelikler : Kaynak yapılabilir, Normalize Edilmiş İnce Damarlı Çelikler
P275N
P275NH
P275NL1
P275NL2
P355N A510AP WStE355 A737gr.B
P355NH A510AP WStE355 A737gr.B
P355NL1 A510FP1 TStE355 gr.490-225
P355LN2
P460N A555AP WStE420 A737gr.C
P460NH A550AP WStE420 A737gr.C
P460NL1 A550FP1 TStE420
P460NL2
EN 10028-5
P355M BSte 355 TM
P355ML1 BSte 355 TM
P355ML2 -
P420M BSte 420 TM
P420ML1 BSte 420 TM
P420ML2 -
S275M FeE275KGTM
S275ML FeE275KTTM
S355M E355R StE355TM FeE355KGTM A572gr.C
S355ML E355FP TStE355TM FeE355KTTM 50EE A633gr.C
S420ML E420R StE420TM A572gr.60
S420ML E420FP TStE420TM A633gr.E
S460M E460R StE460TM FeE460KGTM A572gr.65
S460ML E460FP TStE460TM FeE460KTTM 55EE
EN 10120 NF A36-211 DIN 17155 UNI 7355 BS 5045 UNE 36129 JISG3116
EN 10083-1 NF A 35-552 DIN 17200 UNI 7846 BS 970 UNE 36011 SAE J403-AISI JIS 4051
Richard Shen
Export Department (Ningbo New Hailong)
Ningbo New-Era Steel Tube Co,.Ltd
Tel: 0086-574-87334900
Fax: 0086-574-87715158
Mobile: 0086-(0)137 3616 4628
Email: Richard@xjygg.com / Richard831228@gmail.com
Msn: Richard831228@hotmail.com
Skype ID: Richard831228
http://www.xjygg.com/en-new/index.asp