Professional Documents
Culture Documents
computers. Before you install or use Connection Sharing, you should contact your Internet
service provider (ISP) or read your ISP's Terms and Conditions of Use policy to determine if you
are permitted to share your connection.
Host configuration
To install Connection Sharing, you can either use the Network Setup Wizard or configure the
shared connection manually.
1. Click Start, point to All Programs, point to Accessories, point to Communications, and
then click Network Setup Wizard.
2. Click Next until you see the Select a connection method dialog box.
3. Click This computer connects directly to the Internet, and then complete the wizard to
successfully install Connection Sharing.
For additional information about configuring Connection Sharing manually, click the following
article number to view the article in the Microsoft Knowledge Base:
306126 (http://support.microsoft.com/kb/306126/ ) How to configure Internet Connection
Sharing in Windows XP
Using the Network Setup Wizard to configure Connection Sharing has the following advantages:
Verify that Internet connectivity is functional from the Connection Sharing host computer
before sharing the connection.
Make sure that the interface to be shared is compatible with ICS. One-way connections,
such as a satellite connection that uses both a satellite interface for downloading data and
a dial-up connection for uploading data, are not compatible with Connection Sharing in
Windows XP.
Make sure that your have selected the correct interface as the shared connection. The
shared interface must be the one that is connecting to the Internet.
If you are trying to configure Connection Sharing manually for a connection, make sure
that the home network adapter does not have ICF enabled. If ICF is enabled, you must
either disable it before you can configure Connection Sharing on the external connection
or use the Network Setup Wizard to enable ICS. The wizard disables ICF on home
networking interfaces.
Verify the IP address on the shared connection to confirm that it is obtaining an IP
address from your ISP.
Verify the IP address on the internal adapter to confirm that it is assigned as 192.168.0.1.
If it is not, disable Connection Sharing on the shared connection, make sure that the
internal adapter is configured to obtain an IP address automatically, and then enable ICS
on the shared adapter.
Check the system log and the Nsw.log file for errors that are related to ICS configuration.
To view the contents of Nsw.log, click Start, click Run, type nsw.log, and then click
OK.
When the installation issue has been resolved and Connection Sharing is enabled, verify that
Internet connectivity is still functional on the ICS host computer before you test the ICS client
computers.
Note: Install Connection Sharing only on the computer that you use to connect to the Internet.
This computer is referred to as the "host" computer. The other computers on the local area
network (LAN) that use the host to connect to the Internet are referred to as "client" computers.
If you configure Connection Sharing on multiple computers on your network, you may receive
error messages that indicate that computers have duplicate IP addresses.
Back to the top
After you verify connectivity on the host computer and verify that it can browse correctly in
Microsoft Internet Explorer, troubleshoot the configuration and connectivity on the client
computers. Follow these steps:
1. Open Internet Explorer to test the opening of a Web page. If Internet Explorer does not
open successfully, continue with the following steps. Make sure that you test Internet
Explorer after each step to determine whether the issue is resolved.
2. Check the IP address that is assigned to the client by going to the Network Connections
folder and double-clicking the adapter that is connected to the home network. This will
open the status interface. On the Support tab, make sure that the assigned IP address is in
the range 192.168.0.x (where x is a number between 2 and 254). If it is not, troubleshoot
physical connectivity between the host computer and the client computer, and verify that
the client computer is configured to receive an address by way of Dynamic Host
Configuration Protocol (DHCP). To check the DHCP settings, follow these steps:
a. Click Start, click Run, type the cmd command, and then click OK.
b. Type the following command to ping the host computer:
ping 192.168.0.1
You will see a series of replies, such as the following, that indicate that
connectivity to the host computer is working:
. If this is not successful, there may be a connectivity issue, or you may have a problem
with TCP/IP on the client computer. To rule this out, ping the IP address of the client
computer. If this is successful, but the ping to the host address was not successful, there is
likely a physical connectivity issue between the two computers.
. Use Internet Explorer to open a Web page by using the IP address. You can obtain the IP
address of a Web site on the Internet by using the ping command from the Connection
Sharing host computer. Verify that the host computer receives a correct reply from the
Web server, because some servers do not respond to ping requests.
If you cannot open pages in Internet Explorer by using the IP address, but the previous
steps were successful, try to open a local .html file. If you can, there is likely a
connectivity or Winsock issue on the client computer. Troubleshoot this behavior as if
Connection Sharing were not in the configuration. For additional information about
viewing the contents of the system log, click the following article number to view the
article in the Microsoft Knowledge Base:
. If you can open the Web site by using the IP address, try opening pages by using the fully
qualified domain name (FQDN), such as http://www.microsoft.com. Failures at this point
indicate that there is a name resolution issue. Verify that the client computer is
configured to use 192.168.0.1 as its DNS server. You can check this by clicking Details
on the Support tab of the adapter status. If 192.168.0.1 is not displayed as the DNS
server, follow these steps:
After you check this, verify that 192.168.0.1 is now displayed as the DNS SERVER
address for the client computer, and then retest connectivity.