Professional Documents
Culture Documents
The newly released program version and download file name is as follows.
[Release version]
Model Program Name Current Ver. New Ver. Program File Name Check Note
Sum
63/283
63/283 Chinese
Product Name Program Name Current New Program File Name Checksum Note
Ver. Ver.
Product Name Program Name Current New Program File Name Checksum Note
Ver. Ver.
A1UD0Y0-F000-G00-C8.exe
A1UD0Y0-1E00-G00-02.exe
->Refer to the revised (*5): It automatically detects CPU and shows each Version.
ineo423/363/283_PRI_ DLBT1101740EN00.doc
2. What changed
DSC2(*2) - -
(*3) Be sure to see Check Sum of COPY PROTECT on Firmware Update screen after completing to download.
(*5) It automatically detects CPU mounted on the MFP board and shows one of the followings.
1. On the MFP with FS527+PK517(2-3 holes) is installed, C11C0 may occur if printing the job with punch.
2. On the MFP with FS-529 is installed, Offset sorting may not be performed correctly.
3. The HDD installation setting is changed from “Installed“ to “Not Installed” automatically. [PEBJHK09005968,
1. Due to effect of the earthquake in Eastern Japan, the scanner FW is changed because the microprocessor (IC400) on
The Board number for the MFP board mounted with the current microprocessor (H8S/2324) : A1UDH020/A1UDH021
The Board number for the MFP board mounted with the new adopted microprocessor (H8S/2424) :
The Board number for the MFP board mounted with the new adopted microprocessor (H8S/2425) :
The Board number for the MFP board mounted with the new adopted microprocessor (H8S/3006) :
If the scanner FW for the current microprocessor (older than G00-C8) is rewritten to the MFP board mounted with the new
adopted microprocessor, “Download N.G” appears only for the scanner FW and if the Main Power SW is turned OFF and
There is no problem even if the new scanner FW is rewritten to the current microprocessor(H8S/2324) on the MFP board
The Scanner FW version for the current microprocessor and for the new adopted microprocessor is different.
xxxxxxx-xxxx-G82-09
xxxxxxx-xxxx-G81-09
2. The Boot Rom is changed by revision up (Rev1.1>>Rev2.1) of CPU (IC100) on MFP board.
“CPU Rev2.1” label is affixed on MFP board if the revision up CPU (Rev2.1) is mounted on MFP board.
If the current Boot Rom (A1UD0Y0-1E00-G00-02) is rewritten to the MFP board mounted with the revision up CPU (Rev.
- The control panel does not light up and MFP hangs up if returning the power save mode or the Sub Power SW is turned
Please rewrite the Boot ROM by using the Boot Rom-only FW for specific use (A1UD0Y0-1E00-G00-02.exe) or the FW
There is no problem even if the new Boot ROM is rewritten to the current CPU (Rev. 1.1) on the MFP board.
For details about the above issues, please refer to TNI: TNBT1100115EN00
3. Functional restrictions
1. When printing PDF file (A3/A4 mixed original) from Acrobat (Acrobat Reader) Ver.8 from PS driver, all pages are printed
on A4 size papers.
[Countermeasure]
2. When switching Authentication Method (General Settings) from "ON (MFP)" to "ON (External Server)", user name that was
registered on MFP is displayed on the operation panel. If you login to the MFP using this user name, authentication failure
occurs.
3. When editing or saving a Phone book data (CSV file) using Excel, over 12-digit Fax number is saved as Scientific
If you use the Phone book (CSV file) that was edited or saved using Excel, please confirm the Fax number before you
4. If you print large file from XPS driver, "Connection Timeout" may be indicated when MFP receives the data, and "Deleted
[Countermeasure]
To avoid this problem, please set the driver to the following condition.
5. If Original Orientation of application is different from Original Orientation of Driver when printing the job from FAX driver,
Please set Original Orientations of application and Driver in the same direction.
6. When sending a job with the following settings, the job is stamped with black even if you set stamp with color.
7. After installing Vender, “Group” and “Program” that were registered when uninstalling the Vender are displayed.
*(After installing the Vender, it is impossible to perform new registration of “Group” and “Program”.)
8. In Web Connection, if you click the following menu buttons before the screen is displayed completely, white screen may be
displayed.
[User Mode]
Job
[Administrator Mode]
9. In PS driver, when setting the followings at the same time, overlay image is shifted from set Binding Margin value and
printed.
-Booklet
-Overlay
-Binding Margin
* Refer to the Readme.txt file which is included in each driver and application for other functional restrictions.
* Additional memory installation is required when using the following Open API functions.
4. How to install
Use USB memory to install. For the details, see the Service Manual.
Conditions for USB memory which can be used for updating the firmware are as follows.
[ROM version]:
You can check the ROM version in service mode, "Firmware Version”
* If “Auto” of Acquire Settings is on, Function Version3 is applied to the Printer Driver automatically.
Please refer to the PRI for “DOCUJET 4236/4228 Mass-Production Program (Ver.G00-C0” for details. (DLBT1101200EN)
OpenAPI:
Detail:
Auth 1.0/1.1/2.0/2.5/3.5
Scan to Application 2.0/2.1/2.2/3.0/3.5
PullPrint 1.0/1.1/2.0/2.5/3.5
Other A 1.0/3.5
Job Management 1.0/3.5
Setup 1.0/1.1/1.2/1.3/2.0/2.1/2.5/3.5
Auth 1.0/1.5/3.5
Scan to Application 1.0/1.1/3.5
Web Browser PullPrint 1.0/1.5/3.5
ScrSvr 1.0/3.5
Launcher 1.0/3.5
* Company names and product names in this document are the registered trademarks for respective companies.