FL-1 & FL-11
® .
Fa rval Single Line
; Parallel Injector
Lubrication Systems
Serving Heavy Industry _
PULP & PAPER MININGTO CONTROLLER
Superior Systems.
|
Heavy industries place heavy demands on equipment
and suppliers. Farval has always met these demands in te
offering precise lubrication systems for servicing this
equipment day after day without fail.
FARVAL Meets the Challenge aad
For over 70 years we have serviced industry with
precise lubrication systems. Farval has supplied
Dualine and Single Line progressive systems to
customers around the world. Now Farval is also
offering parallel injector systems with equal attention
to the needs of our customers.
Equipment That Makes the Difference
Every lubrication system we manufacture is designed FLI2
to meet or exceed the demands of our customers. Farval
and our distribution network are now equipped to offer
a complete chive of positive displacement lubrication peageee
devices to meet any demand. We can work with the eaves
Engineering or Maintenance departments to satisfy the
individual needs of any application. We are never more
than a phone call away. For complete lube system FLAt
evaluation and application assistance call FARVAL.
|
SOLENOID
FAL UNT AESALNE —— f+]
VENTVALVE |. ____ LUBRICANT
SUPPLY LINE
FLIa
AIR INLETFL-1 & FL-11 SERIES INJECTOR
TANDARD FEATURES
Competitive, and fully interchangeable
with existing systems components.
+ Electroless nickel plated for superior
corrosion protection
+ Viton seals to protect against high heat
and synthetic lubricants.
+ Larger maximum output than current
competitive models. (FL-1)
+ Less resistant multi-open internal flow
path to discharge piston. (FL-1)
FL-1 & FL-11 Series
ajectors are positive displacement type.
They have adjustable outputs and a visual
cycle indicator pin. They can handle
lubricants up to an NLGI No. 2 grease.
FL-1 Single units have 3/8” NPT male
inlet, manifolded units have 3/8 NPT
female inlet. FL-11 injectors have 3/8”
NPT female inlet. All incorporate grease
filler fitting for priming of system.
13843
1/4 NPT
A
FLA
Adjustable
(KL-11) Min, .050 cu, in. (.819¢c)
(RL-11) Max, .500 cu, in. (8.19¢e)
Output
(FL-1) Min, .008 cu. in. (.131¢¢)
Operating Pressure
Min. 1850 psi (125 bar)
Max. 3500 psi (238 bar)
Recommended 2500 psi (170 bar)
Vent
(recharge pressure)
‘Max. 600 psi (41 bar)
Lubricant Outlet
(FL-1) 1/8” NPT female
(FL-L1) 1/4” NPT female
FL
1/8 NPTF
FL-1 SERIES
MODEL NO, Dimensions = inches (mm)
A 8
13844 ‘Single Injector with 3/8 NPT male adapter
13849, Replacement injector for existing manifolds
FLIA Single inj. mainfold 212 (63)
FLI2 “Two inj. maniford . 3 (76)
FLI-3 Three inj. manifold [114 (92) [41/4 (108) 6.98
FLI-4 Four inj.mantlold [21/2 (63) [5 172 (140) (17)
ELIS Five inj. manifold (3.3/4 (95) [69/4 (171)
FLT6 Sixinj. manifold [5 (127) _[@ (203)
FLY8 Eight inj. manifold [75 (191) [105 (267)
“Single hole mounting
Injector manifolds have one or two 13/82" dia. mounting holes,
818 NPTF
oes1/4 NPTF Air Inlet
Vent Valve Part No. 13850
Vent Valve is used with Farval FL Series Injectors to relieve
system pressure back to reservoir after a lubrication cycle. With a
pneumatic operated pump, air pressure would be applied to the
vent valve at the same time as the pump. When air pressure is
relieved from pump and vent valve, lubricant moves past the valve
seat and out vent port, and piped back to the reservoir.
425
Specifications (108)
1/4 NPTF Vent Port
to Reservoir
Lubricant Supply
(2) Ports, 9/4 NPTF
INJECTOR COVER CAPS
1,
‘Cover caps are used in environments where excessive mois- fe
ture, dirt and other contaminants exist. They are intended to -
protect the internal components of the FL Series Injector from P
corrosion, abrasion, etc,
U1732D
Slips over adjusting housing of FL-1 Series Injectot. ILis made
of clear vinyl plastisol which allows visual check of indicator
pin function,
U1732B
Slips over adjusting bolt of FL-11 - material same as U1732D
CAP13896A
Aluminum cap slips over FL-I Series Injector body.
INJECTOR CONNECTOR TUBE
No. 138
‘Combines discharge of two or more FL-1 Series Injectors through
‘one feed line, It is used when a bearings lube requirement
cannot be met from one injectors output. Fittings have
1/8 NPT male threads,
Farval® Lubrication Systems, Inc.
'ASUBSIDIARY OF VESPER CORPORATION
2685 Airport Road * Kinston, NC 28504 ¢ Tel. 800-227-1063 * Fax: (252) 527-9232
‘/www.farval.com
worldwide website: http: