Professional Documents
Culture Documents
TRAINING
MANUAL
LCD-DV Troubleshooting
55" Class Full HD 1080P
LCD TV (54.6" diagonally)
• Speakers
Section 1
This Section will cover Contact Information and remind the Technician of Important
Safety Precautions for the Customers Safety as well as the Technician and the
Equipment.
Basic Troubleshooting Techniques which can save time and money sometimes can
be overlooked. These techniques will also be presented.
This S
Thi Section
ti willill gett the
th Technician
T h i i familiar
f ili with
ith the
th Disassembly,
Di bl Identification
Id tifi ti and
d
Layout of the LCD Display Panel.
CAUTION
To avoid personal injury, disconnect the power before servicing this product. If electrical power is required for
g
diagnosis or test p
purposes,
p , disconnect the p
power immediately y after p
performing
g the necessaryy checks. Also be
aware that many household products present a weight hazard. At least two people should be involved in the
installation or servicing of such devices. Failure to consider the weight of an product could result in physical
injury.
Today’s sophisticated electronics are electrostatic discharge (ESD) sensitive. ESD can weaken or damage
the electronics in a manner that renders them inoperative or reduces the time until their next failure.
Connect an ESD wrist strap to a ground connection point or unpainted metal in the product. Alternatively,
you can touch your finger repeatedly to a ground connection point or unpainted metal in the product. Before
removing a replacement part from its package, touch the anti
anti-static
static bag to a ground connection point or
unpainted metal in the product. Handle the electronic control assembly by its edges only. When
repackaging a failed electronic control assembly in an anti-static bag, observe these same precautions.
Regulatory
l Information
f
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed g to p
provide reasonable p
protection against
g harmful
interference when the equipment is operated in a residential installation. This equipment generates, uses,
and can radiate radio frequency energy, and, if not installed and used in accordance with the instruction
manual, may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful interference to
radio or television reception
reception, which can be determined by turning the equipment off and on on, the user is
encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate
the receiving antenna; Increase the separation between the equipment and the receiver; Connect the
equipment to an outlet on a different circuit than that to which the receiver is connected; or consult the
dealer or an experienced radio/TV technician for help.
Training Manuals, Schematics with Navigational Bookmarks, Start-Up Sequence, Owner’s Guides,
I t
Interconnect
t Diagrams,
Di Dimensions,
Di i Connector
C t IDs,
ID Product
P d t Pictures
Pi t and
d Features.
F t
1. Check the appearance of the Replacement Panel and Circuit Boards for both physical
damage and part number accuracy.
2 Check the model label
2. label. Verify model names and board model matches
matches.
3. Check details of defective condition and history. Example: Oscillator failure dead set, etc…
•Define Look at the symptom carefully and determine what circuits could be causing
the failure. Use your senses Sight, Smell, Touch and Hearing. Look for burned parts and
check for possible overheated components. Capacitors will sometimes leak dielectric material
and give off a distinct odor
odor. Frequency of power supplies will change with the load
load, or listen for
relay closing etc. Observation of the front Power LED may give some clues.
•Localize After carefully checking the symptom and determining the circuits to be
checked and after giving a thorough examination using your senses the first check should
always be the DC Supply Voltages to those circuits under test. Always confirm the supplies
are not only the proper level but be sure they are noise free. If the supplies are missing check
the resistance for possible short circuits.
•Isolate To further isolate the failure, check for the proper waveforms with the
Oscilloscope to make a final determination of the failure. Look for correct Amplitude Phasing
and Timing of the signals also check for the proper Duty Cycle of the signals. Sometimes
“glitches”
glitches or “road
road bumps”
bumps will be an indication of an imminent failure
failure.
•Correct The final step is to correct the problem. Be careful of ESD and make sure to
check the DC Supplies for proper levels. Make all necessary adjustments and lastly always
perform a Safety AC Leakage Test before returning the product back to the Customer.
Customer
Media Box
TV A/V Inputs
Wi l
Wireless Receiver/Transmitter
R i /T itt
“Dongle”
Attaches via Velcro to
the back of the set
HDMI
• 3D Ready*
R d * • ENERGY STAR® Q Qualified
lifi d
• LED Plus w/Local Dimming • Intelligent Sensor
• NetCast™ Entertainment Access* • AV Mode II (Cinema, Sports, Game)
• (Wi-Fi®
(Wi Fi® R
Ready)
d ) • Clear
Cl V
Voice
i II
• Wireless 1080p Ready* • ISFccc® Ready
• DLNA Certified® (JPEG Only) • 24P Real Cinema
• TruMotion 240Hz • USB 2 2.0
0 (JPEG
(JPEG, MP3
MP3, DivX HD)
• Full HD 1080p Resolution • DivX® HD
• 8M:1 Dynamic Contrast Ratio • 4 HDMI™ V.1.4a Inputs
• Picture Wizard II (Easy Picture Calibration) • SIMPLINK™
SIMPLINK Connectivity
• Smart Energy Saving • Dolby® Digital 5.1 Decoder
• Infinite Sound
*3D - For a small percentage of the population, the viewing of stereoscopic 3D video may cause discomfort such as
headaches, dizziness or nausea. If you experience any symptoms, discontinue using the 3D functionality and contact
your health care provider. 3D glasses required and sold separately. NetCast internet connection & subscriptions required
and sold separately. Wireless 1080p Ready requires the Wireless Media Hub which is sold separately. Design, features and
specifications are subject to change without notice. Non-metric weights and measurements are approximate.
© 2010 LG Electronics USA, Inc. All rights reserved. “LG
LG Life’s
Life s Good
Good” is a registered trademark of LG Corp. All other
product and brand names are trademarks or registered trademarks of their respective companies. 06/22/10
Invisible Speaker
Personally tuned by Mr. Mark Levinson for LG
TAKE IT TO THE EDGE newly y introduces ‘Invisible Speaker’
p system,
y ,
guaranteeing first class audio quality personally tuned by Mr. Mark
Levinson, world renowned as an audio authority. It provides Full Sweet
Spot and realistic sound equal to that of theaters with its Invisible
Speaker.
Sa e Energy,
Save e gy, Sa
Save e Money
o ey
It reduces the plasma display’s power consumption.
The default factory setting complies with the Energy Star requirements
and is adjusted to the comfortable level to be viewed at home.
(Turns on Intelligent Sensor).
TruMotion 240Hz
Unblur the action. See sports, video games and high-speed action with virtually
no motion blur and in crystal clarity with LG’s TruMotion 240Hz technology.
Now your TV can keep up with the fastest moving scenes.
Wireless Ready
Wireless 1080p Connectivity lets you cut loose from messy wires and
still get a stunning Full HD picture. Disclaimer: Wireless media kit
required and sold separately.
Picture Wizard
Get easy self-calibration with on-screen reference points for key picture
quality elements such as black level, color, tint, sharpness and
backlight levels. Take the guesswork out of picture adjustments with
this simple-to-use feature. It's not actually magic, but it will sure seem
that way.
Easy Self
E S lf Calibration
C lib ti
Find the perfect picture. Get easy self-calibration with on-screen
reference points for key picture quality elements such as black level,
color, tint, sharpness and backlight levels. Take the guesswork out of
picture adjustments
p j with this simple-to-use
p feature. It’s not actually
y
magic, but it will sure seem that way.
Remote AKB72914018
MKJ39170828
105-201M
LAN
USB 2
USB 1
Component or
Composite
Video/Audio 3
MAIN BOARD
Rear and Side
Input/Output locations
HDMI 4
Software
Version
found on the
USB Flash
Drive
File found
on the USB
Flash Drive
Prepare
p the Jumpp Drive as described in the “USB Automatic Download” section and insert it into either of the USB p
ports.
Bring up the Customer’s Menu and scroll to “OPTIONS”.
Press the “FAV” key 7 times to bring up the Manual Download Screen.
Highlight
g g the Software update
p file
and press “SELECT” to begin the
download process.
WARNING:
Use extreme Caution
when using the
Manual “Forced”
Download Menu. Any
file can be
downloaded when
selected and may
cause the Main board
to become inoperative
Example of files found if the incorrect file
On the Jump Drive was selected.
Model Name : 55LX6500-UA (Liquid Crystal Display) Parental Control : Channel is not blocked
Memory DVI/HDMI Status
FLASH : 524288 KB Can’t display this information now
DRAM : 524288 KB
Wireless Host Ver:0.00.0
NVM : 128 KB Wireless B/B Ver:0.00.0
Host Release Version RF Region Config : Not Configured
Media Box Type : Not Configured
Firmware Version(MP) : 4.10.04.01(51822) Software VersionRF Frequency (Value):Auto (N.A.)
Micom Version : 3.05.4 Uplink RF Power gain (Value):Auto
Compile Date & Time : 20101112 & 15:17:49 (Min 0)
Downlink RF Power gain (Value):Auto
Compile User : kyuhae.leeChannel Frequency Link Mode : Unicast
FAT Status (Main) RX MAC Address : ff:ff:ff:ff:ff:ff
Center Frequency : 663.00 MHz TX MAC Address : ff:ff:ff:ff:ff:ff
Wireless connection
PCR lock : Locked Program Clock Reference (Locked or No)
status:Disconnected
Modulation mode : QAM 256 Channel Type (8VSB, QAM 64, Average
256) SNR [db]:0.0(0)
Carrier lock status : Locked Channel (Locked or No) 8VSB (Above 20 is good)
SNR : 40 dB Channel Signal to Noise Ratio QAM 64 (Above 24 is good)
QAM 256 (Above 30 is good)
Signal level : 100% Channel Signal Level (Above 80% good)
Current Channel (Main)
Note: When PCM is downloaded, AC3 will be N/G and when AC3 is downloaded PCM will be N/G.
Thi means that
This th t when
h PCM iis OK
OK, PCM audio
di is
i priority
i it and
d when
h AC3 isi OK,
OK AC3 audio
di isi
priority.
7.1/2”
190mm
17.13/16” 15.3/4"
452.5mm 400mm
31.3/8"
797.56mm
15.3/4"
Center
400mm
34.1/8" 15.11/16"
866.14mm 398.78mm
Model No.
Serial No. 8.1/4” Remove 4 screws to
Label 210mm remove stand for
wall mount
2.11/16" 1.3/16"
(68.58mm) 117mm
22.9/16"
573mm 4.5/8"
Weight w/o Stand 63.5 lbs 345.44mm
Weight with Stand 76.1 lbs
3D
This section of the manual will discuss the
55LX6500 LCD Direct View Television ability to
play 3D material.
600
IR Emitter
User friendly Glasses Location
1)) L-frame for g
glasses users 3
2) UV coating to prevent scratch
1
3) LED indicator for user convenience
4) Easy to Recharge with USB port
2
Input
Input
Input
4. In case 3D looks *abnormal, press “L/R (1)
Select” on remote and select “R/L”.
*Abnormality may be caused by reversed L/R HDMI Component
order of the input signal. If TV already in USB
Component Composite
Left/Right change to Right/Left or vice versa. Port
RF RF, S-Video
(3)
(4)
(2)
Note: The Left and Right eye are actually seeing the same image but from a different angle, but
for this explanation one is shown inverted from the other for clarity purposes simply to show there
is a difference between the two images seen by each eye.
<F
Frame 1 >
Battery
IR
R
Receiver
i
TN LCD shutter
Sync
signal
TV with built in
Shutter Actuator IR Transmitter
3D Formatter
- All F
Formats
t off input
i t are available
il bl and
d converted
t dbby 3D ttechnology
h l
- Full HD input available
- 3D Enhancement
1) Side by Side
1) Line by Line
2) Top and Bottom
R
L 2) Frame by Frame
3) Checkerboard 3D Formatter
R
4) Frame
F Sequential
S ti l
(Full Resolution available) L
OK
Check 3D_SYNC Line OK Possible *FPGA (Main) or *FRC (T-CON/3D) has problems.
Main P7800 pin 49 Replace It or T-CON/3D Board.
T-CON/3D P802 pin 2
NG
*FPGA: Field Programmable Gate Array
For details about making the 3D Sync line check, see next page.
*FRC: Frame Rate Converter
Should be
Q906
NG B) 0.61V
Replace
OK E) Gnd Q906 (Collector)
T-CON
C) 0.03V 5.5V p/p 60 Hz
(Formatter B/D)
Q907
B) 0V Q907 (Collector)
E) Gnd 3.9V p/p 60 Hz
Possible Main or C) 1.9V
T-CON/3D has problems.
Replace T-CON/3D or
Main Board Additional Information On the 3D Emitter Board
“3D-Emitter" to P2401 "Main"
Diode
Pin LABEL SBY Run
Check 5.3V p/p 12 MHz
1 +5V_EMITTER 0V 5.1V Open
2 Gnd Gnd Gnd Gnd
5.5V p/p
60 Hz 3 3D_SYNC 0V 1.6V Open
1
IC100 Q102
5) 5.1V 4) 5.1V
B) 0V
6) 0V 3) 1.6V
E) Gnd
7) 0V 2) 2.15V
C) 3.5V
8) Gnd 1) 5.1V
LED LED
5.5V p/p
Check 3D_SYNC Line 60 Hz
Main P802 pin 2 1.6VDC
IC502
25MHz IC310
P803
IC307 L802 P804 P802 X100 P101
IC308 P7800 P2401
11.42V
IC200 IC204 2.53V Pin 50 Pin 3
LVDS 12V L314
TP 2.52V
IC304 Q1002
L307 C E E B Q1001
3D Board Q702
L702
B C C
B
B E
E C
IC305
Q1003 Q1004
P900 IC1000 L309
n/c 3D IR
CB
B EE
C Q906
Q907 Q906
B) 0.61V Check 3D_SYNC Line
IC1002 IC1001
E) Gnd Pin 3
C) 0.03V
Q907 5.5V p/p
IC309 IC306 B) 0V
60 Hz
L600 E) Gnd
1.6VDC
D603 L601 C) 1.9V
25
3.4V
D602
IC500
IC600 48
13
A2 IC400
C
A1 D601
A1
A2 C
D600
IC501 SW400
IC801
P806 P805
3DC safety guidelines for distribution of 3D displays suitable for human eyes were made
at the 3D Consortium 2006
Disassembly:
This section of the manual will discuss Disassembly
Disassembly,
Layout
(Circuit Board Identification) of the 55LX6500 LCD
Direct View Television.
Television
The AC Cord
Does Not unplug
Inverter
Clip Clip
Power Supply
(SMPS) Main Board
LVDS Cable
Clip T-CON/3D
Clip
Soft Touch
Key Board Panel Connection
Points
CN103 CN102
CN2
CN101
P7803
P7800
P7901 P8000
POWER P7802
SUPPLY n/c P2401
P1000
p/n: EAY60908802
P8200 MAIN
BOARD
P8100 p/n: EBR69488901
P803 P804 P802 P101 n/c 55LX6500-UB_AUSWLJR
n/c
p/n: EBU60987802
P900 Comes with Panel P8800 55LX6500-UB_AUSWLUR
SK101
T-CON
n/c
AC In P806 P805
To TFT
Soft Touch Keys Panel
J3 J1
J2
IR/Intelligent Speaker (Front Right) Center Speaker (Front Left) 3D Emitter board
Sensor board p/n: EAB60961501 LOGO p/n: EAB60961501 Original: p/n: EBR69838801
Sub: p/n: EBR72073501
p/n EBR64966201
Use Sub p/n for interference
on certain remotes.
Press in gently on
the two tabs
Disconnect to release lock
P201, P204
and AC In
SK101 fits very
SK101. snug into it’s
connector.
Remove the 6
screws indicated
by the arrows.
Press in on the
SK101
two tabs
to release lock
AC In
NOTE: If Servicing
NOTE S i i the
th Board,
B d putt the
th CN2
screws back in the board to provide
stability and grounding.
The Inverter
Th I t will
ill run without
ith t
Local Dimming signals being
provided by CN2
1. Lay the TV down on its face. Use some scratch resistant material to avoid damaging the front frame.
2 Remove the stand support bracket that surrounds the T-CON/3D board.
2. board (6 screws) See Fig.
Fig 1.
1
6 3
Stand Bracket
5 4
Fig. 2
1 2
Push In Push In
P802
4
3
P806 P805
P805
P806
Cushion Cushion
Chocolate
Chocolate
J1
To the Main
P8200
Tab Tab
Troubleshooting: g
This section of the manual will discuss troubleshooting.
47uF/450V
47uF/450V
47uF/450V
47uF/450V
47uF/450V
47uF/450V
F501 Hot Gnd
(A) Jump pins 9, 10, 11 or 12 (3.5V) to pin 1. (Test Q111 Q110 STBY 159.6V 23 N/C n/c n/c Open
D D
Voltage Outputs 12V, 24V to Main and 24V to both S G S G Run 392.6V 24 ERR OUT 0V 0V Open
Inverters). Remove AC power. Leave the jumper in place.
C
Q606 (1)
23 21 19 17 15 13 11 9 7 5 3 1 A
G P-DIM Pin 20 can vary according to incoming video
12V 12V 12V 24V D
Q605 IRE level, OSD Backlight setting and
STBY 3.5V
A S
PWR ON
G
- D room light condition.
BD101 S
0.37V 0% to 3.3V 100% and the Intelligent Sensor.
D100
Output from the Video Processor IC900.
SMPS TEST 2 +
CX101
STBY 3.5V
INV-ON
F100
CX103
CX102
B
24V 24V
6.3A/250V
24 22 20 18 16 14 12 10 8 6 4 2
P201
23 21 19 17 15 13 11 9 7 5 3 1
RL102 SK101
12V 12V 12V 24V E
RL101 B AC In
STBY 3.5V
A C
PWR ON
P-DIM
BOARD
RL_On
TEST 1
1: No Backlights during this test
(1) Add a jumper between (3.5V STBY) pin 7, 8, 9 or 10 and Pin 1 (PWR_ON). Apply AC.
This will turn on the power supply, relays will click.
a)) Check that the 24V and 12V power
p supplies
pp are turned on,,
• P201 (12V pins 17, 19 and 21)
• P201 (24V pins 2, 3 and 4)
• P204 (24V pins 1 through 5) to the Inverter
Backlights Normal:
a) If normal, the backlights should turn on.
SMPS OK, Inverter OK. Pin 1 is the
Brown Wire
Backlights Abnormal:
a) Recheck all connections.
b) Confirm the INV On/Off line pulling up to at least 3V and arriving at both Inverters.
c) Check the connections to the Inverters.
If the 24V and the Inverter On command is arriving at the Inverters in, then see Inverter Section
for further testing.
REMOVE AC POWER:
P204 1
(1)
PDIM Pin 11 can vary y accordingg to incoming
g video IRE level, OSD
Backlight setting and then Intelligent Sensor (room light condition)
Output from the Video Processor IC900. Range 0.27V to 3.3V.
(2) I-C is the Inverter On Control Signal
SK101 "SMPS" to AC IN
F100
Bottom
Right of
SMPS F100 (Diode Check)
L N Main Power Switch Closed
SK101
F501
F501
3 15A/250V
3.15A/250V
Inverter 134V
• (M1 134V) IC101, IC1, IC2, Q101, D101, D111 C130, L101 and L102.
Out CN102 and CN103.
• (M2 134V) Q141, D141, D151, C170, L201 and L202.
Out CN102 and CN103.
Connector One LED can be tested with a Diode Check using a Connector
DVM. Forward biased, the LED should light.
CN102 or CN103
LED Drive Signal 50 IRE
Global 134V
And Driver
Local On
Dimming Inverter
Control 1 Block 6.38V drop per/LED
32V p/p 10mSec
3 V5 0V 1
Open To Q111 C E
6 V8 0V 1
1V~30V Open 100uF D16 C
Q7
L201 250V
D75
7 V13 0V Gnd Open
8 V14 0V 1
1V~30V Open D141 IC601 To
1 C141 CN2 Main
9 V15 0V 1V~30V Open
100uF
1
10 V16 0V 1V~30V Open 35V 250V
1000uF
12 n/c n/c n/c Open 24V
35V D151
12 Out_M2 0V 134V Open 1000uF
Q141 Y1 CN1
1
Black to White 35V
100uF
12MHz n/c
250V
1000uF
- +
L202
Q285 E B
C
Q287
Q286
EB C
Q283 E B
B
C C B E
IC2 IC1
E C
Q284 IC101
Q163 C
B E Q281
C
Q162 C
IC102
Q151
BE
C E
B
B E Q282
INVERTER
L301 Q164 Q161 CN3
n/c
IC103
220uF
35V
Q216
The Red outlined Q208
Q101
D111 The Red outlined
Area on the left is 35V
1000uF
100uF
Q207 Area on the right
The 24V input from
250V
- + 24V
250V
IC201
C130 LED Drivers
Q203
Q201
Q201~Q216
F101 24V Q123 C Q122
12A/65V Q202
Q121 M1
24V in Pins 1~5
BE
- +
E B
D75 On indicates there is a problem
100uF D16 C
Q7
L201 250V
D75
D141 IC601 Local Dimming
C141 Signals from the
Main Board
100uF
35V 250V
1000uF CN2
35V D151
1000uF
Q141 Y1
12MHz
100uF
35V 250V
1000uF
- + 24V C170
L202
Q285 E
C
B
Q287
Q286
EB C
Q283
E B
B
C C B E
IC2 IC1
E C
Q284 IC101
C
C
B E Q281
Q162 C
LED Drivers
(See Connector CN102 and CN103 for pin outs)
Q201 drives V1 Block, Q202 drives V2 Block
Through Q216 drives V16
42V p/p
/ (Thi
(This shows
h th
the LED
LEDs att 50% b
brightness.
i ht
Low = LEDs On. High = LEDs off.
1 2
2
3 1 3
1 1
1 1
F101
12A/65V
F102
12A/65V
12Mhz
Y1
80 IRE 5 IRE
35V p/p 240Hz 35V p/p 240Hz
Note: If a particular area is exhibiting a dimmer level than the other or the overall brightness seems dim, be
sure to first check the customer’s Menu setting for Backlights. Raise the percentage and see if the overall
brightness returns to normal. If not,
1st Check the P-DIM level, it should rise with the percentage shown on screen. 0% = 0.37V to 100% = 3.3V.
Follow the P-DIM signal all the way to each Inverter.
2ND Turn off the set and unplug the connector to the Inverter coming from the Main board. If the brightness
returns to normal,
normal the Main board is defective.
defective If not,
not investigate all inverter voltages,
voltages if OK,
OK use the
grounding of each V block driver procedure to test the panel’s backlight LEDs.
1V per/div 50uSec 3.43V p/p 1V per/div 50uSec 3.43V p/p 1V per/div 100mSec 3.31V p/p
80% brightness
Diode Mode values taken with all Connectors Removed 35V p/p 240Hz
2 0.96V 2 7.09V C
E 1.57V D141
3 1.27V Q161 B 4.34V 1 23.58V
3 Gnd Q284 B 2.51V
4 1.26V C E C 2.86V 2 133.5V
4 1V B
C 1.58V
5 1.78V E Gnd B
3 23.1V
5 2.72 E C
E 2.52V
6 1.59V D151
Q111 Q162 B 2.85V
7 n/c Q285 B 0V 1 23.58V
1 2.84V C C 0V
8 Gnd B
C 2.51V 2 133.5V
2 24.44V BE E 2.86V
E
9 24.49V C
E Gnd 3 23.1V
3 Gnd
10 4.43V Q163 1 2.86V
11 1/58V 2 7.07V Q286 B 2.72V
Q121 B 4.34V
12 1/78V 3 2.82V
C C 0V
C E C 2.86V
13 1.26V B BE E Gnd
E Gnd
14 1.56V Q164 1 2.86V Q287 B 0V
15 0V Q122 B 2.85V 2 Gnd E B C 0.07V
16 2.52V
C
C 0V 3 2.82V C E Gnd
BE E 2.86V
IC103 1 2.72V Q123 1 2.86V Q201 through Q216
2 4.2V 2 7.07V B 0.73V
3 5.94V 3 2.82V C 1~30V
E Gnd
B C E
4 Gnd
5 1.72V Q124 1 2.86V Collector Voltage White to Black
6 2.72V 2 Gnd Q201 (Block V1) to Q216 (Block V16)
7 0V 3 2.82V These transistors ground the 16 LED Blocks
8 24.47V
T-CON/3D B+: 12V is supplied to the T-Con Board from the Main Board P7800 and P7802.
Delivered by two connectors P802 and P803 easily measured at the Test Point just to the left of
the P803 on L802.
These Voltages can also be measured at the ribbon connectors delivering signals to the TFT
panel using TPs.
P805: “16V” pins 1-2, “3.34V” pins 4-5, “8.17V” pins 7-8, “-4.9V” pin 11, “25.63V” pin 16, “6V”
pins 18-19, “8V” pin 21, “15.75V” pins 23-24 and “3.33V” pin 45.
P806: 16V pins 79-80, 3.34V pins 76-77, 8.17V pins 73-74, -4.9V pin 71, 25.63V pin 66, 6V pins
63-64, “8V” pin 61, 15.75V pins 44 and “3.33V” pin 36.
Also, See the 11X17 Foldout (Interconnect Diagram) for more details.
B EE
C
Q906 21 Gnd Gnd Gnd
Q907 22 RRXA3- 1.20V 1.67V
23 RRXA3+ 1.14V 1.67V
IC1002 IC1001 24 RRXA4- 1.26V 1.67V
25 RRXA4+ 1.08V 1.67V
26 Gnd Gnd Gnd
27 n/c n/c n/c
IC600
28 RRXB0- 1.19V 1.67V
B+ Source IC306
IC309 29 RRXB0+ 1.19V 1.67V
11.42V 3.4V 23-24
L600 30 RRXB1- 1.19V 1.67V
LVDS 12V
Pins 37-38 11.22V
3.4V L601 31 RRXB1+ 1.16V 1.67V
D603 11.27V L601 32 RRXB2- 1.2V 1.67V
16V
16V Pin 42
25
3.4V 33 RRXB2+ 1.14V 1.67V
D602 34 Gnd Gnd Gnd
IC500
IC600 48
13
A2 IC400 35 RRXBCK- 1.16V 1.67V
C
A1 D601
6V Pin 2 A1 36 RRXBCK+ 1.2V 1.67V
25.6V Pin 8 A2 C -5V (A1)
D600 37 Gnd Gnd Gnd
8V Pin 11
SW400 38 RRXB3- 1.22V 1.67V
IC501
39 RRXB3+ 1.14V 1.67V
8.2V Pins 73-74 3.4V Pins 4-5 40 RRXB4- 1.26V 1.67V
25.6V Pins 66
3.4V Pins 76-77
IC801 16V Pins 1-2
8.2V Pins 7-8
41 RRXB4+ 1.09V 1.67V
P806 8V Pin 61 8V Pin 21 P805
42-46 Gnd Gnd Gnd
16V Pins 79-80
6V Pins 63-64 -5V Pins 71
-5V Pins 11
6V Pins 18-19
47 n/c n/c n/c
25.6V Pins 16
48-51 PANEL_VCC 11.59V Open
Check pins
49~51(12V)
P803 P804
Check
pins 1 or 2
(12V)
P803 L802
IC302
L307 SC414MLTRT L306 +1.0VDC
3A
Q700
L700 +3.3V_TCON
FET
IC700
MAX15023
Q702 L702 +1.8V_TCON
FET
P805
L600 L307 Pin 8: VCC_LCM (+3.3V) LCD
Module
23-24
42 P806
IC600 Pin 42: VDD_LCM (+16V)
TPS65162 8
R601 Pin 8: VGH (+27V)
14
D601
VGL (-5V)
See the previous page for the development for the voltages for P806 and P805
connectors which are Panel voltages.
X100
1 71V DC
1.71V 1 65V DC
1.65V
25Mhz
T-CON/3D Board
18 Gnd Gnd Gnd 41 RRXB4+ 1.09V 1.67V *Pin 2 Only active when a 3D
source is played. (1.63V)
19 RRXACK- 1.16V 1.67V 42-46 Gnd Gnd Gnd
P804
P804 Connector "T-CON/3D Board“ to P7803 "Main"
Diode Check taken with meter in Diode Mode with all Connectors Removed
26 V4 13 35V
13.35V 53 G d
Gnd G d
Gnd 79 RRMV6N 1 22V
1.22V
3 LLMV0N 1 24V
1.24V 30 LRMV4N 1 25V
1.25V 56 V16 0 27V
0.27V
26 LRMVCLKN 1 21V
1.21V 53 V13 4 94V
4.94V 79 VDD (16V) 16V
To T-CON/3D
P7800
To T-CON/3D
T CON/3D
Component or
Composite
These connectors
LAN are Mini plug type
Wireless
Wi l Media
M di Box
B Headphone
Remote
P8800 To Speakers
INV_CTL Sw P2401
IC9703
X9700 EEPROM Q8005
25MHz 3D Sync
1.8V Dimming D3.3V Reg
IC9701 IC9702 IC8008
LG5111 3
IC8005
LVDS & Dimming 3
1
2
2
1
Q D
EC C
B Rubber
A1 A2
1
Power On
Power On 3 2
Sw Q8002 Q8000 Driver
IC602
DDR_VTT Reg IC606 IC604
Q8205
Wireless IR_PASS
DDR DDR Q8203
IC8100
Q200
+1.8V_HDMI D S
Switch G
IC602 D1.8V IC8400 RGB IC8700 Wireless Q200 (1.8V_HDMI) Q8203 IR Wireless Pass
Pin Regulator Pin H/V Sync Pin Buffer Pin Switch Pin 2nd Driver
[1] 0V (Gnd) [1] 1.9V [1] 0V (3.3V Dongle In) S 1.83V (Out) B 0V
[2] 3.29V (PWR On/Off1 Ctl) [2] 1.9V [2] 3.3V (0.3V Dongle In) G 3.35V (PWR On/Off2 Ctl) C 3.3V
[3] 0.9V (DDR_VTT) [3] 4.4V [3] n/c D 1.83V (In) E Gnd
[4] 0.93V [4] 0V [4] n/c
[5] 1.83V [5] 0.9V [5] n/c Q701 Tuner SIF
[6] 3.38V (In) [6] n/c (4.5V) [6] Gnd Pin (Sound) Buffer Q8205 IR Wireless Pass
[7] 1.8V (Out) [7] 0V (Gnd) [7] Gnd B 0.16V Pin 1st Driver
[8] 0.91V (DDR_VTT) [8] n/c (4.5V) [8] Gnd C Gnd B 0.6V
[9] n/c (1.9V) [9] n/c E 0.83V C 0V
IC8100 EEPROM [10] n/c (1.9V) [10] 0.02V E Gnd
Pin Micro [11] n/c (4.5V) [11] 0V Q702 Tuner Video
[1] 0V (Gnd) [12] 0.9V [12] 3.3V Pin (Analog) Buffer Q8300,1,2,6 HDMI 1
[2] 0V (Gnd) [13] 0.9V [13] 0V (3.3V Dongle In) B 2.05V Pin Hot Swap
[3] 0V (Gnd) [14] 5V [14] 3.3V C 2.75V B 4.2V
[4] 0V (Gnd) [15] 3.3V E Gnd C 0V
[5] 3.37V IC8401 EDID Data [16] 3.3V E Gnd
[6] 3.37V Pin PC Q901 FLASH_WP
[7] 0V (Gnd) [1] 0V (Gnd) Pin for IC901 Q8303,4,5,7 HDMI
[8] 3.37V [2] 0V (Gnd) B 0V (Flash_WP) Pin Hot Swap
[3] 0V (Gnd) C 3.36V B 0V
IC8200 RS232 [4] 0V (Gnd) E Gnd C 4.2V
Pin Routing [5] 0.7V E Gnd
[1] 0V [6] 4.1V Q8000 RL_ON (PWR_On)
[2] 0V [7] 4.5V Pin 1st Driver Q8308 CEC Remote
[3] 0V [8] 4.5V (In) B 0.66V Pin HDMI CEC
[4] 0V C 0V [B] 2.72V
[5] 0V E Gnd [G] 2.73V
[6] (-5.47V) [S] 3.27V
[7] n/c (5.59V) Q8002 PWR_ON [D] 3.37V
[8] n/c (0V) Pin Switch
[9] n/c (3.3V) [1] 3.36V (In) Q8701 IR Wireless Pass
[10] n/c (0.2V) [2] 0V Pin 2nd Driver
[11] n/c (3.3V) [3] 3.3V (Out) G 24.5V (2.3V Dongle In)
[12] 3.35V S 24V
[13] 0V D 0V (24.5V Dongle In)
[14] (-5.47V)
[15] 0V (Gnd) D8306,7,9,10 5V Pull Up Routing D8312 3.5V Pull Up
[16] 3.37V Pin HDMI SCL/SDA Pin HDMI CEC
A1 5.04V A1 0V
C 4.58V C 3.26V
A2 0V A2 3.2V
1 6V
1.6V
4.5V p/p
25Mhz
725mV p/p
Do not measure with
Digital Volt meter
Runs when
set is On
MAIN Board
X8100
3.48V p/p Top leg
Either leg
MAIN Board
X8101
32.768KHz
Can not read 3V p/p
A Waveform on 1.47V
left side 1.8V
11 RRXB4+ 1 09V
1.09V 0 97V
0.97V 28 RRXA4-
RRXA4 1 26V
1.26V 1 15V
1.15V 45 n/c n/c n/c
15 G d
Gnd G d
Gnd G d
Gnd 32 RRXACK
RRXACK+ 1 2V
1.2V 0 97V
0.97V 49 V SYNC
V_SYNC 3 33V
3.33V 0 998V
0.998V
*Pin 50 O
*Pi Only
l active
ti when
h a 3D 5.5V
5 5V p/p
/ 60 H
Hz
source is played. (1.63V) 3D-Sync
(1) Clock p
pulses only
yppresent when Intelligent
g Sensor is turned on. ((3.7V p
p/p)
p)
(2) IR pulses (2.5V p/p)
1
Diode Mode values taken with
all Connectors Removed
Q8800 IC8800
Amp 1.8V
Mute
Pin 25
Q8800 (Mute)
Active Low.
Location:
Top left of IC8801. IC8801
Normal 3.3V Collector to
Pin 25 of all three ICs. (1)
N t 3
Note: 3.3V
3V iinputt ((pin
i 3)
from IC8005
Audio B+
3.3V_Normal Regulator
24.7V
Pins 49-52
The Intelligent Sensor and IR board (located on the bottom left as viewed from the rear) contains the
IR (Infrared Remote Sensor) and the Intelligent Sensor. This board also connects with the Soft Touch
Key Board and the Center LG Logo board. The Center LG Logo lights after power on and the picture
appears. Then dims down in about 2 seconds. At power off, it does the reverse. It will remain on
when the set is on if set up in the Customer’s Menu.
The IR board receives it operating B+ via J1 pin 6 (STBY 3.5V) 3.44V in STBY and 3.34V in Run.
The IR (Infrared) remote receiver can be measured (3.44V) at pin 9 of connector J1 or P8200 on the
Main board in Stand-By. During run pin 9 reads (1.48V).
The IR pulses (1.6V p/p) J1 pin 9 are sent to P8200 on the Main board and on to the Microprocessor
(IC8101) via pin 16.
The Intelligent Sensor communicates with the Micro/Video Processor IC900 BCM Chip via clock and
data lines SCL1 and SDA1 arriving on connector J1 from P8200 pins 1 and 2 on the Main board.
The Front Power LEDs are controlled by these same Clock and Data lines which communicate with
the LED Driver IC on the IR board.
The Key board is routed to the IR board via CON2 and output on J1 Key 1 and Key 2 lines, (Key 1 pin
4 and Key 2 pin 5). Arriving at P8200 pins 4 and 5 on the Main Board.
Then to the Microprocessor 25 and 26 lines.
J3 To LG LOGO
Board
J1 To Main Board
Back View
This section shows the 11X17 foldout that’s available in the Paper
and Adobe version of the Trainingg Manual.
Pin Label STBY Run LED Backlights V1~V16 Drive Signals 2 PANEL_VCC 11.59V Open 27 RRXA4+ 1.08V 0.97V
Check Raise the percentage and see if the overall brightness returns to normal. If not, If either connector (P102 or P103) is 3 PANEL_VCC 11.59V Open 28 RRXA4- 1.26V 1.15V
to LED Blocks
1-5 24V 0V 24.49V 0.43V 1st: Check the P-DIM level, it should rise with the percentage shown on screen. (100% = 3.3V). disconnected D75 will illuminate. The 4 PANEL_VCC 11.59V Open 29 RRXA3+ 1.14V 0.97V
Follow the P-DIM signal all the way to the Inverter. backlights will still light, but appear dimmer. *To force a Block to turn on, simply ground the pin labeled V1~V16. 5 n/c n/c n/c 30 RRXA3- 1.2V 1.15V
6-10 Gnd Gnd Gnd Gnd 5% Brightness 80% Brightness Providing the 134V source is present.
2nd: Turn off the set and unplug the connector CN2 to the Inverter coming from the Main 6 Gnd Gnd Gnd 31 Gnd Gnd Gnd
11 n/c n/c n/c Open 35V p/p 240Hz 35V p/p 240Hz
board. If the brightness returns to normal, the Main board is defective. 7 Gnd Gnd Gnd 32 RRXACK+ 1.2V 0.97V
8 Gnd Gnd Gnd 33 RRXACK- 1.16V 1.15V
12 *I-C 0V 2.92V Open CN102 "Inverter" To "Panel LEDs" White Plug CN103 "Inverter" To "Panel LEDs" Black Plug 9 Gnd Gnd Gnd 34 Gnd Gnd Gnd
13 *P-DIM (VBR-B) 0V 0.37V~2.8V Open Pin Label STBY Run Diode Check Pin Label STBY Run Diode Check 10 Gnd Gnd Gnd 35 RRXA2+ 1.14V 0.97V
Q209
14 ERROR 0V 0V Open INVERTER 1 Out_M1 0V 134V Open 1 Out_M1 0V 134V Open 11 RRXB4+ 1.09V 0.97V 36 RRXA2- 1.22V 1.15V
CN103 CN102
12 RRXB4- 1.26V 1.15V 37 RRXA1+ 1.17V 0.97V
Q212 Q211 2 n/c n/c n/c Open 2 n/c 0V Gnd Open
Q210 13 RRXB3+ 1.14V 0.97V 38 RRXA1- 1.19V 1.15V
I-C is Inverter On (INV)_ON) n/c M2 3 V1 0V *1V~30V Open 3 V5 0V *1V~30V Open 14 RRXB3- 1.22V 1.15V 39 RRXA0+ 1.19V 0.97V
P201 "SMPS" To P8000 "MAIN"
P205 Diode
134V
Q213
4 V2 0V *1V~30V Open 4 V6 0V *1V~30V Open 15 Gnd Gnd Gnd 40 RRXA0- 1.17V 1.15V
Pin Label STBY Run L101 Q214 5 V3 0V *1V~30V Open 5 V7 0V *1V~30V Open
16 RRXBCK+ 1.2V 0.97V 41 n/c n/c n/c
Check 17 RRXBCK- 1.16V 1.15V 42 3D_DIM_2 0.05V 1.03V
1 -
PWR-ON 0V 3.28V 1.7V D101 6 V4 0V *1V~30V Open 6 V8 0V *1V~30V Open 18 Gnd Gnd Gnd 43 3D_DIM 0V 1.03V
P204 P201 Q215
- +
2-4 24V 0V 24.57V 0.43V 100uF
7 n/c 0V Gnd Open 7 V13 0V *1V~30V Open 19 RRXB2+ 1.14V 0.97V 44 3DTV 0V Open
A1
250V
D201 C 5-8 Gnd Gnd Gnd Gnd 8 V9 0V *1V~30V Open 8 V14 0V *1V~30V Open
20 RRXB2- 1.2V 1.15V 45 n/c n/c n/c
SMPS BOARD Q252 9-12 3.5V 3.44V 3.37V Open D111
Q216
Q208 21 RRXB1+ 1.16V 0.97V 46 FRC_RESET 3.32V Open
C = 3.45V 9 V10 0V *1V~30V Open 9 V15 0V *1V~30V Open
p/n: EAY60908802 A1/A2 = 0V A2 13-15 Gnd Gnd Gnd Gnd 35V Q101 *1V~30V *1V~30V
22 RRXB1- 1.19V 1.15V 47 SCL3_3.3V 3.34V 1.04V
Q251
250V
24 RRXB0- 1.19V 1.15V 49 V_SYNC 3.33V 0.998V
11 V12 0V *1V~30V Open 12 n/c n/c n/c Open
Ground 17 12V 0V 11.81V 1.4V 35V
1000uF 25 n/c n/c n/c *50 3D_Sync_Out 0.03V Open
Q206 12 n/c n/c n/c Open 12 Out_M2 0V 134V Open
D222 IC103 18 INV--ON 0V 3.17V Open 35V L102
51 Gnd Gnd Gnd
A2 n/c n/c n/c Open - + 24V IC201 * Black to White 5.5V p/p 60 Hz
T501 20 3D-Sync
11 Open 35V
D151 there is a 1.8V Dimming D3.3V Reg P2401
Y1 1 n/c 0V 0.02V Open IC9701 IC9702
SMPS TEST 2: (B) Jump pins 9, 10, 11 or 12 12 Open
1000uF
Q141 problem. LG5111
IC8008
3
2 n/c Gnd Gnd Gnd IC8005
(3.5V) to pin 18 (INV-ON). Apply AC power, the 12MHz
100uF
35V LVDS & Dimming 1 2
Open
3 2
13
250V
1000uF 1
Backlights should turn on. CN1 3 n/c Gnd Gnd Gnd IC8007 + 5V Normal Reg
D102 14 Open - +
n/c 4 M2_MOSI 0V 3.27V Open Q8003 Q8001 A1.2V Reg
IC8003
L202 D IC8002 IC8001
Note: If the Inverter is loading down 24V and For voltages Q287 P2300 n/c Panel Vcc Sw
F101 Hot Gnd D101 Q285 5 Gnd Gnd Gnd Gnd
E B
G S
causing the SMPS to shut down, See the SMPS Q8004
C
Q286
EB
Q283 E B C
IC2 IC1 6 M2_SCLK 0V 0.05V Open D1.8V Reg
STBY 2.9V
C C B E
D607 Q284
E C
220uF
USB2
35V
X8100 IC302
P7901 to P8000 to IC900 IC901
D603 10MHz Micro
processor Video Processor
NAND Flash
Memory
USB1 5V
C SMPS TEST 1 Inverter CN2 SMPS P201
IC8101 LGE3549XQ
A
D602
STBY 3.5V
IC8800
G
Q605 S 23 21 19 17 15 13 11 9 7 5 3 1 IC502
N/C
Pin LABEL Run Diode
3 1.06V 5-8 Gnd
+1.8V_AMP
- 25MHz IC310 4 Gnd 9-12 1.11V +1.26V_TU Reg
D 12V 12V 12V 24V P803 IC308 1 PANEL_VCC 11.55V Open Q8800
STBY 3.5V
IC700
BD101 S IC307 L802
IC200
X100 2 PANEL_VCC 11.55V Open 5 1.06V 13-15 Gnd IC8801
Audio EBR69488901 55LX6500-UB_AUSWLJR
Earphone Amp
11.42V IC204 2.53V 3 Gnd Gnd Gnd 6 Gnd 16 Open IC8300 IC300
Amp HDMI BU60987802 55LX6500-UB_AUSWLUR Side
LVDS 12V L314 4 Gnd Gnd Gnd
7 Gnd 17 Open Selector Main Board Used: AV
+ D100 TP 2.52V
Q308 TU700
SMPS TEST 2 P804 “TCON" to P7803 "Main Board" 8 1.06V 18 1.61V RGB RS232
CX101 IC302 IC205 IC102 TDVJ-H031F
STBY 3.5V
CX102
24 22 20 18 16 14 12 10 8 6 4 2
L305 8.2V IC700 3.33V 3 E_TDO 3.33V Open 21
Q? Analog
13. 1.26V
P201
12. GND
4 E_TMS 0.35V Open 22 Open
Video 11. CVBS
23 21 19 17 15 13 11 9 7 5 3 1 3.35V 3.34V L700 HDMI Audio 10. NC
8. NC
A Q1002 Tuner
PWR ON
7. SDA
Front pins on connector
L702 24 Open
Wireless Media
Audio Audio Clock 6. SCL HDMI
E L307 C E E B Q1001 1.85V 1.88V Box Remote
AC In
5. NC
RL101 B are odd numbers.
2.5V
B C
2.3V
C
JK8700
HDMI
Tuner B+ 4. NC
3. 5V
C B E
B
E C
IC305 P7802 "Main" To "T-CON” P803 For voltages
Q231 Q1003 Q1004 2. NC
Pin LABEL Run Diode Check See the SMPS Spk P8800 1. NC
Q8307
P802 "T-CON" to P7800 "MAIN Board" P900 IC1000 L309 1.2V
1 PANEL_VCC 11.55V Open table for P201
Pin Label Run Diode Check Pin Label Run Diode Check
n/c 1.27V
CB
2 PANEL_VCC 11.55V Open
P806 LVDS to Panel P805 LVDS to Panel 1 Gnd Gnd Gnd 24 RRXA4- 1.26V 1.67V
B EE
C
Q906
3 Gnd Gnd Gnd
PIN LABEL RUN PIN LABEL RUN PIN LABEL RUN PIN LABEL RUN PIN LABEL RUN PIN LABEL RUN
*2 3D_Sync_Out 0.03V 2.34V
Q907 To the Speakers P8800 "Main" To "Speaker”
25 RRXA4+ 1.08V 1.67V 4 Gnd Gnd Gnd
1 Gnd Gnd 28 Gnd Gnd 54 V14 3.75V 1 VDD (16V) 16V 28 V6 11.08V 54 RLMVCLKP 1.19V
2 LLMV0P 1.19V 29 LRMV4P 1.15V 55 V15 2.68V 2 VDD (16V) 16V 29 V7 10.28V 55 RLMVCLKN 1.18V
3 V_SYNC 3.33V 1V 26 Gnd Gnd Gnd P8200 "Main Board" To J1 "IR Board" Pin LABEL Run Diode Check
4 SDA3_3.3V 3.34V 1.73V IC1002 IC1001 1 Spk_R+ 12.28V Open
3 LLMV0N 1.24V 30 LRMV4N 1.25V 56 V16 0.27V 3 Gnd Gnd 30 V9 8.31V 56 Gnd Gnd 27 n/c n/c n/c Pin Label STBY Run Diode Check
4
5
LLMV1P
LLMV1N
1.18V 31
1.3V 32
LRMV5P
LRMV5N
1.18V 57
1.26V 58
V17
V18
0.26V
0.26V
4
5
VCC (3.3V) 3.4V
VCC (3.3V) 3.4V
31
32
V10
V12
7.71V
3.37V
57
58
RLMV4P
RLMV4N
1.15V
1.24V
5
6
SCL3_3.3V
FRC_RESET
3.34V
3.32V
1.73V
Open
28
29
RRXB0--
RRXB0+
1.19V
1.19V
1.67V
1.67V
1 SCL 3.45V 3.37V Open
2
3
Spk_R-
Spk_L+
12.28V
12.28V
Open
Open 3D IR
6 LLMV2P 1.15V 33 LRMV6P 1.17V 59 Gnd Gnd 6 Gnd Gnd 33 V13 4.94V 59 RLMV5P 1.34V 2 SDA 3.45V 3.37V Open 4 Spk_L- 12.28V Open
7 n/c n/c n/c
7 LLMV2N 1.29V 34 LRMV6N 1.25V 60 Gnd Gnd 7 HVDD (8V) 8.2V 34 V14 3.75V 60 RLMV5N 1.22V 30 RRXB1-- 1.19V 1.67V IC600
8 Gnd Gnd 35 Gnd Gnd 61 Z_OUT 8V 8 HVDD (8V) 8.2V 35 V15 2.68V 61 RLMV6P 1.12V
8
9
3DTV
3D_DIM
0V
0V
Open
Open
31 RRXB1+ 1.16V 1.67V B+ Source
IC309 IC306 Soft Touch Keys 3
4
Gnd
KEY 1
Gnd
3.45V
Gnd
3.37V
Gnd
1.86V
JK8700 Jack "MAIN Board" P2401 "Main" To "3D Emitter”
9 LLMVCLKP 1.22V 36 OPT_N 3.33V 62 Gnd Gnd 9 Gnd Gnd 36 V16 1.97V 62 RLMV6N 1.23V 32 RRXB2-- 1.2V 1.67V 11.42V 3.4V 23-24 To "Wireless Dungle" Pin LABEL Run Diode Check
10 LLMVCLKN 1.23V 37 H_CONV Gnd 63 VCOMLOUT 6V 10 OPT_P n/c 37 V17 0.27V 63 Gnd Gnd 10 3D_DIM_2 0.05V Open
LVDS 12V L600 5 KEY 2 2.76V 2.7V 1.86V
33 RRXB2+ 1.14V 1.67V Pin Label STBY Run Diode 1 +5V_EMITTER 5.1V Open
11 Gnd Gnd 38 GSP 0V 64 VCOMLFB 6V 11 VGL--(5V) (-5V)
- 38 V18 0.26V 64 RRMV0P 1.13V 11 n/c n/c n/c 3.4V L601 6 3.5V_ST 3.46V 3.37V 1.11V
12 Gnd Gnd 39 Gnd Gnd 65 RRMV0N 1.23V 34 Gnd Gnd Gnd Pins 37-38 11.22V
1-6 *24V 0V 24.65V Open 2 Gnd Gnd Gnd
12 LLMV4P 1.18V 39 POL 1.66V 65 Gnd Gnd 12 RRXA0-- 1.17V 1.67V D603 11.27V L601 7 Gnd Gnd Gnd Gnd 0V 0.3V 2.38V 3 3D_SYNC 0.03V Open
13 LLMV4N 1.26V 40 Gnd Gnd 66 VGH (26V) 25.6V 13 GOE 0.83V 40 GSP 0V 66 RRMV1P 1.15V 35 RRXBCK-- 1.16V 1.67V 16V 7 Detect
13 RRXA0+ 1.19V 1.67V 25
3.4V 8 LED_LOGO 0V 0.82V Open 8 Interrupt 0V 3.3V Open
14 LLMV5P 1.26V 41 SOE_L 0.24V 67 Gnd Gnd 14 GSC 2.3V 41 POL 1.66V 67 RRMV1N 1.23V 36 RRXBCK+ 1.2V 1.67V 16V Pin 42
14 RRXA1-- 1.19V 1.67V D602 9 Gnd 0V Gnd Gnd
15 LLMV5N 1.27V 42 Gnd Gnd 68 GSC 2.3V 15 Gnd Gnd 42 Gnd Gnd 68 RRMV2P 1.15V
IC600 9 IR 1.57V 1.52V Open Original: p/n: EBR69838801
16
17
LLMV6P 1.16V 43
LLMV6N 1.26V 44
V1
V2
15.75V 69
15.75V 70
GOE
Gnd
0.83V
Gnd
16
17
VGH (26V) 25.6V
Gnd Gnd
43
44
SOE_R
H_CONV
0.25V
0.44V
69
70
RRMV2N
Gnd
1.23V
Gnd
15
16
RRXA1+
RRXA2--
1.17V
1.22V
1.67V
1.67V
37
38
Gnd
RRXB3-
Gnd
1.22V
Gnd
1.67V
IC500 48
13
C A2
A1 D601
IC400 J2 J1 10 Gnd Gnd Gnd Gnd
10
11
n/c
Gnd
0V
0V
3.3V
Gnd
Open
Gnd
Sub: p/n: EBR72073501
Front IR
6V Pin 2
J3
A1
11 +3.3V_Normal 0V 3.33V 0.50V 12 I2C_SCL 0V 3.3V 1.04V
18 Gnd Gnd 45 V3 14V 71 VGL (-5V) (-5V)
- 18 VCOMRFB 6V 45 OPT_N 3.33V 71 RRMVCLKP 1.19V 39 RRXB3+ 1.14V 1.67V -5V (A1)
19 LRMV0P 1.17V 46 V4 12.26V 72 Gnd Gnd 19 VCOM ROUT 6V 46 Gnd Gnd 72 RRMVCLKN 1.18V
17 RRXA2+ 1.14V 1.67V 25.6V Pin 8
A2
D600
C
12 LED_R/BUZZ 0V 0V Open
13 I2C_SDA 0V 3.3V 1.04V Use Sub p/n for interference
18 Gnd Gnd Gnd 40 RRXB4- 1.26V 1.67V 14 Gnd 0V Gnd Gnd
20 LRMV0N 1.28V 47 V5 11.07V 73 HVDD (8V) 8.2V 20 Gnd Gnd 47 RLMVOP 0.15V 73 Gnd Gnd 8V Pin 11
SW400 on certain remotes.
41 RRXB4+ 1.09V 1.67V IC501 15 Wireless_RX 0V 3.3V 1.8V
21
22
LRMV1P 1.15V 48
LRMV1N 1.26V 49
V6
V7
11.07V 74
10.27V 75
HVDD (8V) 8.2V
Gnd Gnd
21
22
Z_OUT
Gnd
8V
Gnd
48
49
RLMVON
RLMV1P
0.17V
0.14V
74
75
RRMV4P
RRMV4N
1.13V
1.24V
19
20
RRXACK--
RRXACK+
1.16V
1.20V
1.67V
1.67V -
42-46 Gnd Gnd Gnd 8.2V Pin 73-74 3.4V Pin 4-5 p/n EBR64966201 J3 "IR" To "LG LOGO" J2 "IR Board" To "Key Board” 16 Wireless_TX 0V 3.3V 1.8V
8.2V Pin 7-8
17 Gnd 0V Gnd Gnd
23 LRMV2P 1.17V 50 V9 8.31V 76 VCC (3.3V) 3.4V 23 V1 15.75V 50 RLMV1N 1.24V 76 RRMV5P 1.11V 21 Gnd Gnd Gnd 47 n/c n/c n/c 25.6V Pin 66 3.4V Pin 76-77
16V Pin 1-2 Pin LABEL SBY Run Diode Pin Label STBY Run Diode 18 IR 0.67V 3.3V Open
24 LRMV2N 1.27V 51 V10 5.74V 77 VCC (3.3V) 3.4V 24 V2 15.75V 51 RLMV2P 1.13V 77 RRMV5N 1.12V
22 RRXA3-- 1.20V 1.67V -
48-51 PANEL_VCC 11.59V Open P806 8V Pin 61 8V Pin 21 P805 1 3.5V_ST 3.46V 3.37V Open 19- 20 Gnd 0V Gnd Gnd
25 Gnd Gnd 52
26 LRMVCLKN 1.21V 53
V12
V13
Gnd 78
4.94V 79
Gnd Gnd
VDD (16V) 16V
25
26
V3
V4
14V
13.35V
52
53
RLMV2N
Gnd
1.22V
Gnd
78
79
RRMV6P
RRMV6N
1.12V
1.22V
23 RRXA3+ 1.14V 1.67V 16V Pin 79-80 -5V Pin 11 LG LOGO 2 Gnd Gnd Gnd
3 Logo Drive 2.19V 0.69V
Gnd
Open
1
2
Key 1
Gnd
3.45V 3.37V
Gnd Gnd
Open
Gnd
Voltages with Dongle plugged in.
*Pin 2 6V Pin 63-64 -5V Pin 71
27 LRMVCLKP 1.23V 80 VDD (16V) 16V 27 V5 12.27V 80 Gnd Gnd
(1.6V) with 3D source IC801 25.6V Pin 16 6V Pin 18-19
3 Key 2 2.76V 2.7V Open
5.5V p/p 60 Hz
4 Gnd Gnd Gnd Gnd (Use Dongle side to read voltages. Remove cover).
4 Gnd Gnd Gnd Gnd
3D-Sync
To TFT Panel To TFT Panel *24V Switched from Q8701 Drain
Q8701 turned on by Q8700
55LX6500 MAIN (FRONT SIDE) SIMICONDUCTORS
IC300 Earphone Amp IC601 NVRAM IC8001 D1.2V and A1.2V IC8004 A2.5V Regulator IC9702 (+1.8V_L/Dimming) Q8003 PANEL_VCC
Pin Pin Pin Regulator Pin for USB Pin Regulator Pin Control 2nd Driver
[1] 0V [1] n/c [1] 0V (Gnd) [1] n/c [1] Gnd B 0.66V
[2] 0V [2] 0V [2] 3.3V [2] 3.26V (B+) [2] 11.74V (B+) C 0V
[3] 0V [3] 3.34V [3] 0V (Gnd) [3] 3.26V (B+) [3] Gnd E Gnd
[4] 0V [4] Gnd [4] 1.27V [4] n/c [4] 0.81V (FB)
[5] 0V (HP R Out) [5] 3.34V [5] 3.32V [5] n/c [5] 0.77V Q8004 PANEL_VCC
[6] 3.3V [6] 0V [6] n/c [6] 2.57V (Out) [6] 3.34V Pin Switch
[7] 3.3V [7] Gnd [7] 4.48V [7] 0.83V [7] 3.32V (Out) S 11.62V (In)
[8] (-1.8V) [8] 3.34V (B+) [8] 3.32V [8] Gnd [8] 3.34V (Out) G 1.8V (Enable)
[9] (-0.88V) [9] 3.32V D 11.8V (Out)
[10] Gnd IC700 (+1.26V_TU) [10] 3.34V IC8005 (+3.3V_NORMAL) IC9703 EEPROM
[11] 0.94V Pin Regulator [11] 1.28V Pin And D3.3V Regulator Pin for LG5111 Q8200 IR Buffer
[12] 1.83V [1] 0V (Gnd) [12] Gnd [1] Gnd [1] Gnd Pin 2nd
[13] 3.32V (Mute) [2] 1.27V (Out) [13] 3.3V [2] 11.74V (B+) [2] 3.34V B 0.56V
[14] 3.32V (B+) [3] 3.32V (B+) [14] 0.82V [3] Gnd [3] Gnd C 0V
[15] Gnd [4] 0.81V [4] Gnd E Gnd
[16] 0V (HP L Out) IC8000 5V Regulator IC8002 D1.8V [5] 0.89V [5] 3.34V
Pin for USB Pin Regulator [6] 3.34V (PWR On/Off2 Ctl) [6] 3.34V Q8201 IR Buffer
IC301 USB 2 [1] 11.75V (B+) [1] 5V [7] 3.36V (Out) [7] 3.32V Pin 1st
Pin 5V [2] 5.1V (Out) [2] 3.35V (B+) [8] 3.36V (Out) [8] 3.34V (B+) B 0V
[1] Gnd [3] 5.1V (Out) [3] 1.83V (Out) C 3.36V
[2] 5.1V (In) [4] 10.5V [4] Gnd IC8007 Power Det Gen Q308 Headphone E Gnd
[3] 5.1V [5] 3.3V [5] Gnd Pin (+12V and +3.5V) Pin Mute
[4] 3.33V [6] 0.81V [6] 2.36V [1] Gnd B 0V Q8307 Side HDMI
[5] 3.33V [7] 5.06V [7] 0.91V [2] 3.6V (B+ C 3.32V Pin Hot Swap
[6] 5.1V (Out) [8] 0V (Gnd) [8] 1.05V [3] 3.5V (Out) E Gnd B 0V
[7] 5.1V (Out) [9] 2.4V C 4.32V
[8] n/c [10] 3.37V (PWR On/Off1 Ctl) IC8008 Power Det Gen Q8001 PANEL_VCC E Gnd
Pin (+24V) Pin Control 1st Driver
IC302 USB 1 IC8003 (+5V_NORMAL) [1] Gnd B 0V Q8800 AMP Mute to
Pin 5V Pin Regulator [2] 3.64V (B+) C 0.68V AMP_MUTE1 IC8801
[1] Gnd [1] Gnd [3] 3.76V (Out) E Gnd B 0V
[2] 5.1V (In) [2] 11.74V (B+) C 3.34V
[3] 5.1V [3] Gnd IC8800 (+1.8V_AMP) Q8700 Wireless PWR E Gnd
[4] 3.33V [4] 0.81V Pin Regulator Dongle Out Turns on Q8701
[5] 3.33V [5] 0.86V [1] Gnd B 0V (0.0V w/Dongle Out)
[6] 5.1V (Out) [6] 3.34V (PWR On/Off2 Ctl) [2] 1.8V (Out) C 24.6V (24V w/Dongle Out)
[7] 5.1V (Out) [7] 5.17V (In) [3] 3.3V (B+) E Gnd
[8] n/c [8] 5.17V (In)
Q8700 Wireless PWR Q8005 INV_ON
Dongle In Turns on Q8701 Pin Driver
B 0.66V (0.0V w/Dongle In) B 0V (INV ON) En
C 0.14V (24V w/Dongle In) C 2.97V (Out)
E Gnd E Gnd
IC602 D1.8V IC8200 RS232 IC8401 EDID Data IC9000 Serial Flash Q702 Tuner Video Q8300,1,2,6 HDMI 2
Pin Regulator Pin Routing Pin PC Pin T-CON Pin (Analog) Buffer Pin Det
[1] 0V (Gnd) [1] 0V [1] 0V (Gnd) [1] 0.06V B 2.05V B 4.2V
[2] 3.29V (PWR On/Off1 Ctl) [2] 0V [2] 0V (Gnd) [2] 0.67V C 2.75V C 0V
[3] 0.9V (DDR_VTT) [3] 0V [3] 0V (Gnd) [3] 3.3V (In) E Gnd E Gnd
[4] 0.93V [4] 0V [4] 0V (Gnd) [4] 0V (Gnd)
[5] 1.83V [5] 0V [5] 0.7V [5] 0V Q901 FLASH_WP Q8303,4,5,7 HDMI 3
[6] 3.38V (In) [6] (-5.47V) [6] 4.1V [6] 0.34V Pin for IC901 Pin Det
[7] 1.8V (Out) [7] n/c (5.59V) [7] 4.5V [7] 3.31V (In) B 0V (Flash_WP) B 0V
[8] 0.91V (DDR_VTT) [8] n/c (0V) [8] 4.5V (In) [8] 3.34V (In) C 3.36V C 4.2V
[9] n/c (3.3V) E Gnd E Gnd
IC8100 EEPROM [10] n/c (0.2V) IC8700 Wireless IC9303 EEPROM
Pin Micro [11] n/c (3.3V) Pin Buffer Pin for LG5111 Q8000 RL_ON (PWR_On) Q8308 CEC Remote
[1] 0V (Gnd) [12] 3.35V [1] 0V (3.3V Dongle In) [1] 0V (Gnd) Pin 1st Driver Pin HDMI CEC
[2] 0V (Gnd) [13] 0V [2] 3.3V (0.3V Dongle In) [2] 0V (Gnd) B 0.66V [B] 2.72V
[3] 0V (Gnd) [14] (-5.47V) [3] n/c [3] 0V (Gnd) C 0V [G] 2.73V
[4] 0V (Gnd) [15] 0V (Gnd) [4] n/c [4] 0V (Gnd) E Gnd [S] 3.27V
[5] 3.37V [16] 3.37V [5] n/c [5] 3.37V [D] 3.37V
[6] 3.37V [6] Gnd [6] 3.37V Q8002 PWR_ON D8312 3.5V Pull Up
[7] 0V (Gnd) IC8400 RGB [7] Gnd [7] 3.34V Pin Switch Pin HDMI CEC
[8] 3.37V Pin H/V Sync [8] Gnd [8] 3.37V (In) [1] 3.36V (In) A1 0V
[1] 1.9V [9] n/c [2] 0V C 3.26V
[2] 1.9V [10] 0.02V Q200 (1.8V_HDMI) [3] 3.3V (Out) A2 3.2V
[3] 4.4V [11] 0V Pin Switch
[4] 0V [12] 3.3V S 1.83V (Out) Q8203 IR Wireless Pass D8306,7,9,10 5V Pull Up Routing
[5] 0.9V [13] 0V (3.3V Dongle In) G 3.35V (PWR On/Off2 Ctl) Pin 2nd Driver Pin HDMI SCL/SDA
[6] n/c (4.5V) [14] 3.3V D 1.83V (In) B 0V A1 5.04V
[7] 0V (Gnd) [15] 3.3V C 3.3V C 4.58V
[8] n/c (4.5V) [16] 3.3V Q701 Tuner SIF E Gnd A2 0V
[9] n/c (1.9V) Pin (Sound) Buffer
[10] n/c (1.9V) B 0.16V Q8205 IR Wireless Pass
[11] n/c (4.5V) C Gnd Pin 1st Driver
[12] 0.9V E 0.83V B 0.6V
[13] 0.9V C 0V
[14] 5V E Gnd
55LX6500 P7901 Main to Inverter CN2 Local Dimming Control Signals Waveforms
1V per/div 50uSec 3.43V p/p 1V per/div 50uSec 3.43V p/p 1V per/div 100mSec 3.31V p/p