Professional Documents
Culture Documents
Issue 5.
March 2015
T1 - For all wovens and jersey garments. Womens lingerie and mens underwear, nightwear, swim, beachwear, Hoisery & Socks
T2 - All knitwear from 12 gauge through to 1.5 gauge
ST - Specific Tolerances can be given at the discretion of the Technical Department for the following garments; Bias cut garments, crinkle
fabrics, special denim wash finishes. Knitwear: Hand Knited garments and accessories.
- Tolerances are specific to the measurement points in the 'How To Measure Guide' .
- All tolerances are in centimetres and on the flat. If circumference measurements are used tolerances must be
doubled.
Example:
Permitted Tolerance
Measurement
Measurement Point Description Key * Levels ( cm only) Page Number
Point Code
T1 T2
Section A - Lengths
A1 Centre back neck to waist +/- 0.5 1 3
A2 Centre back neck to hem +/- 1 1.5 3
A3 Centre back length (skirt) +/- 1 1.5 3
Page 1 of 7
Primark Permitted Tolerance Tables
Issue 5.
March 2015
Primark Adult Garment Tolerance Tables - Issue 5. March 2015
Page 2 of 7
Primark Permitted Tolerance Tables
Issue 5.
March 2015
Primark Adult Garment Tolerance Tables - Issue 5. March 2015
Page 3 of 7
Primark Permitted Tolerance Tables
Issue 5.
March 2015
Primark Adult Garment Tolerance Tables - Issue 5. March 2015
Page 4 of 7
Primark Permitted Tolerance Tables
Issue 5.
March 2015
Primark Adult Garment Tolerance Tables - Issue 5. March 2015
Page 5 of 7
Primark Permitted Tolerance Tables
Issue 5.
March 2015
Primark Adult Garment Tolerance Tables - Issue 5. March 2015
Page 6 of 7
Primark Permitted Tolerance Tables
Issue 5.
March 2015
Primark Adult Garment Tolerance Tables - Issue 5. March 2015
Section AB - Hats
AB1 Bevel height +/- 0.5 1 65
AB2 Crown length +/- 0.5 1 65
AB3 Crown width +/- 0.5 1 65
AB4 Brim depth +/- 0.5 1 65/67
AB5 Brim circumference +/- 0.5 1 65
AB6 Hat length +/- 0.5 1 65/67
AB7 Hat circumference +/- 0.5 1 65
AB8 Peak point to peak point +/- 0.5 1 66
AB9 Peak depth +/- 0.5 1 66
AB10 Crown height along seam +/- 0.5 1 66
AB11 Hat Circumference - total +/- 0.5 1 66/67
AB12 Total length - knotted hat +/- 0.5 1 66
AB13 Width at x cm up from seam +/- 0.5 1 66
AB14 Dart length +/- 0.5 1 65
AB15 Panel width at seam +/- 0.5 1 66
AB16 Back elastic width +/- 0.5 1 66
AB17 Ear width +/- 0.5 1 67
AB18 Front hat length +/- 0.5 1 67
AB19 Back hat length +/- 0.5 1 67
AB20 Cord length +/- 0.5 1 67
Section AE - Mittens and Gloves
AE1 Glove length +/- 0.5 0.5 68/69
AE2 Glove width +/- 0.5 0.5 68/69
AE3 Thumb length +/- 0.5 0.5 68/69
AE4 Fore finger length +/- 0.5 0.5 68/69
AE5 Index finger length +/- 0.5 0.5 68/69
AE6 Third finger length +/- 0.5 0.5 68/69
AE7 Little finger length +/- 0.5 0.5 68/69
AE8 Cuff depth +/- 0.5 0.5 68/69
AE9 Cuff width at opening +/- 0.5 0.5 68/69
AE10 Cuff Depth +/- 0.5 0.5 69
Section AF - Scarves
AF1 Scarf length +/- 1 1.5 70
AF2 Scarf width +/- 1 1.5 70
Section AG - Ear Muffs
AG1 Head band circumference +/- 0.5 1 71
AG2 Ear muff length +/- 0.5 0.5 71
AG3 Ear muff width +/- 0.5 0.5 71
* Key
T1 All wovens, jersey, nightwear, swimwear, lingerie and mens underwear. Hosiery and Socks.
T2
All Knitwear from 12 gauge through to 1.5 gauge
Specific Tolerances can be given at the discretion of the Technical Department for the following garments; Bias cut
ST
garments, crinkle fabrics, special denim wash finishes, Hand knited garments and accessories.
~ Where the tolerance column is blank; a specific measurement must be achieved. Refer to the Techncial Department or
+/- The tolerance level is acceptable above or below the specific measurement
Page 7 of 7