QKERFKORE
FLEXBOARD® SPECIFICATIONS
Pe
base layer manufact
ayer that allows easy attachmer
using Flexboard the decorative surfac
ly stable
seminigid mat
formed into the des
pressure
mate
‘a maximum 8" radius
Standard Material
High-Quality Particleb
Standard Options
MDF
Plywood
Specialty Options
Fire Rated Particleboard
NAF FSC Particleboard
Other core materials may be available upon request.
Standard Material: Eu
yptus Hardboard (,090" Thickness}
HighPres
Ven
Metal
ure Laminates (vertical, post formable, standard)
lar Materials
Maximum Achievable Radius: 8 when using 3/4" Flexboard
Note: While a smaller radius may be obtainable, itis t before proceeding.
1, Any contact cement recommended for use with laminate:
the use of a J-rolle
venee
hould be acceptable with
DO NOT USE RIGID
ystems may cau!
TING ADHESIVES such
ridge lines and face fractures.
PVAC, hot melt glue, epoxy, etc. These adhesi
2, PVA glue is acceptable for atta
provided that Flexboard is being
below for more information,
ning a single ply
inated flat. Si
eneer or a 10mil paper backed veneer
e decorative surface application process
Note: It is be
proceeding,
t to te ermine how the materials will work tagether before
nen forming a free:
nding part, PVA glues end wood glues are
acceptabQKERFKORE
To achieve amaximum radius, apply the decorative surface after the
The decorative
irface can also be applied to Flexboard while flat and then formed into the desire:
This is only pos
or 10mil paper backed venee
ated flat
Contact Adhesive
ble ifusing a single ply ven
i dius: 16" ywith Flexboard lami
contact adhesive to both material:
LIGHT TO MODERATE pressure when bonding the d
irm hand pressure or moderate pressure with a Jroller.
irfacing material to Flexboard
PVA Glue
If applying a decorative surface to Flexboard while flat, apply PVA glue to one side only, either the
decorative surfacing material or the Flexboard material will work.
Adequate uniform pressure should be applied.
Recommended Pressure: 100 psi
Drying Time & Temperature: Use glue manufacturer's recommen
Note: Due to vai
determine the corr
d decorative surfacing m
Adhesives c prayed, bi J, of rolled on. A medium coat of adhesive
ally, less adhesive is better than too much
Make freestanding part
curve
e. doors) by gluing a backing sheet to the rib side while
Dent into the desired
Note: Using a PVA glue or woad glue to attach backing sheet will provide a rigid glue bond
‘Tip: For consistency use a vacuum forming process for an extremely uniform part. Great wh
repeatability is require
can be edge banded using contact or PVA glue.
Cor
he rigid par
Important: Always acclimate Flexboard to the same envi
materials that are being used. Two to three days are recomr
>mmended by the face material manufacturer.
onment as tl orative surfacin
1d for conditioning. Use the guideliQKERFKORE
Lifting: Requires two people
Moving: Pick up in a manner to avoid pinching fing! een the grooves
Important: Do Not over flex the material or bend it pa rmmended radius when handling.
e flat with the face material side facing up.
low for air circulation, keep in a dry area and away from direct contact with the floor
Flexboard has approximately the same impact resistance as simila ed,
Call 912-264-6496 for additional information
FENDERS weer)
Note: Product identified as 48' " will bend like a column, 9 ill bend like a barrel
96" x 43"
48" x 96"
BOARD CLASSIFICATION AND DIMENS
Ne eset
ened E E xo
Additional technical information available a