Professional Documents
Culture Documents
Size:(mm) A-1A-F
a b c d e
The temperature at which a Thermal Cutoff changes its state of conductivity to open circuit
Tf-Rated functioning detection current. The tolerance according to IEC60691 is from +0 to -10degC. (With Japan
temperature: Electrical Appliance and Material Law, on the other hand, they must function in the tolerance
range of +/-7degC)
The fusing-off temperature indicates value measured in silicon oil with a temperature
Fusing-off temperature:
increased by 0.5-1degC per minute and a detective current 100mA or less.
The maximum temperature at which a Thermal Cutoff will not cause a change in state of
Th-Holding temperature: conductivity to open circuit while conducting rated for 168 hours. This rating is required
The maximum temperature at which a Thermal Cutoff can be maintained for 10 minutes without
Tm-Maximum temperature limit:
re-closing. This rating is required by safety standards based on IEC60691
Ur-Rated voltage: The allowable maximum voltage which a Thermal Cutoff is able to be applied.
P-1A-F
Size:(mm) P-1A-F
a b c d e
The temperature at which a Thermal Cutoff changes its state of conductivity to open circuit detection
Rated functioning temp.(Tf): current. The tolerance according to IEC60691 is from +0 to -10degC. (With Japan Electrical Appliance
and Material Law, on the other hand, they must function in the tolerance range of +/-7degC)
The fusing-off temperature indicates value measured in silicon oil with a temperature increased by
Fusing-off temperature:
0.5-1degC per minute and a detective current 100mA or less.
The maximum temperature at which a Thermal Cutoff will not cause a change in state of conductivity
Holding temperature(Th): to open circuit while conducting rated for 168 hours. This rating is required by safety standards
based on IEC60691
The maximum temperature at which a Thermal Cutoff can be maintained for 10 minutes without re-closing.
Maximum temp. limit(Tm):
This rating is required by safety standards based on IEC60691
Rated voltage(Ur): The allowable maximum voltage which a Thermal Cutoff is able to be applied.
A-F
Size:(mm) (A-F )
a b c d e
The temperature at which a Thermal Cutoff changes its state of conductivity to open circuit detection
Rated functioning temp.(Tf): current. The tolerance according to IEC60691 is from +0 to -10degC. (With Japan Electrical Appliance
and Material Law, on the other hand, they must function in the tolerance range of +/-7degC)
The fusing-off temperature indicates value measured in silicon oil with a temperature increased
Fusing-off temperature:
by 0.5-1degC per minute and a detective current 100mA or less.
The maximum temperature at which a Thermal Cutoff will not cause a change in state of conductivity
Holding temperature(Th):
to open circuit while conducting rated for 168 hours. This rating is required by safety standards
The maximum temperature at which a Thermal Cutoff can be maintained for 10 minutes without
Maximum temp. limit(Tm):
re-closing. This rating is required by safety standards based on IEC60691.
Rated current(Ir): The allowable maximum current which a Thermal Cutoff is able to carry.
Rated voltage(Ur): The allowable maximum voltage which a Thermal Cutoff is able to be applied.
P-F
Size:(mm) (P-F)
a b c d e
The temperature at which a Thermal Cutoff changes its state of conductivity to open circuit detection
Rated functioning
current. The tolerance according to IEC60691 is from +0 to -10degC. (With Japan Electrical Appliance
temp.(Tf):
and Material Law, on the other hand, they must function in the tolerance range of +/-7degC)
The fusing-off temperature indicates value measured in silicon oil with a temperature increased
Fusing-off temperature:
by 0.5-1degC per minute and a detective current 100mA or less.
The maximum temperature at which a Thermal Cutoff will not cause a change in state of conductivity
Holding temperature(Th):
to open circuit while conducting rated for 168 hours. This rating is required by safety standards
The maximum temperature at which a Thermal Cutoff can be maintained for 10 minutes without
Maximum temp. limit(Tm):
re-closing. This rating is required by safety standards based on IEC60691.
Rated current(Ir): The allowable maximum current which a Thermal Cutoff is able to carry.
Rated voltage(Ur): The allowable maximum voltage which a Thermal Cutoff is able to be applied.
A-3A-F
Size:(mm) (A-3A-F)
a b c d e
The temperature at which a Thermal Cutoff changes its state of conductivity to open circuit
Rated functioning temp.(Tf): detection current. The tolerance according to IEC60691 is from +0 to -10degC. (With Japan
Electrical Appliance and Material Law, on the other hand, they must function in the tolerance
The fusing-off temperature indicates value measured in silicon oil with a temperature
Fusing-off temperature:
increased by 0.5-1degC per minute and a detective current 100mA or less.
The maximum temperature at which a Thermal Cutoff will not cause a change in state of
Holding temperature(Th): conductivity to open circuit while conducting rated for 168 hours. This rating is required
The maximum temperature at which a Thermal Cutoff can be maintained for 10 minutes without
Maximum temp. limit(Tm):
re-closing. This rating is required by safety standards based on IEC60691.
Rated current(Ir): The allowable maximum current which a Thermal Cutoff is able to carry.
Rated voltage(Ur): The allowable maximum voltage which a Thermal Cutoff is able to be applied.
P-3A-F
Size:(mm) (P-3A-F)
a b c d e
detection current. The tolerance according to IEC60691 is from +0 to -10degC. (With Japan
Rated functioning temp.(Tf):
Electrical Appliance and Material Law, on the other hand, they must function in the tolerance
range of +/-7degC)
The fusing-off temperature indicates value measured in silicon oil with a temperature increased
Fusing-off temperature: by 0.5-1degC per minute and a detective current 100mA or less.
The maximum temperature at which a Thermal Cutoff will not cause a change in state of conductivity
Holding temperature(Th): to open circuit while conducting rated for 168 hours. This rating is required by safety standards
based on IEC60691.
The maximum temperature at which a Thermal Cutoff can be maintained for 10 minutes without
Maximum temp. limit(Tm):
re-closing. This rating is required by safety standards based on IEC60691.
Rated current(Ir): The allowable maximum current which a Thermal Cutoff is able to carry.
Rated voltage(Ur): The allowable maximum voltage which a Thermal Cutoff is able to be applied.
A-5A-F
a b c d e
The temperature at which a Thermal Cutoff changes its state of conductivity to open circuit
detection current. The tolerance according to IEC60691 is from +0 to -10degC. (With Japan
Rated functioning temp.(Tf):
Electrical Appliance and Material Law, on the other hand, they must function in the tolerance
range of +/-7degC)
The fusing-off temperature indicates value measured in silicon oil with a temperature
Fusing-off temperature:
increased by 0.5-1degC per minute and a detective current 100mA or less.
The maximum temperature at which a Thermal Cutoff will not cause a change in state of
Holding temperature(Th): conductivity to open circuit while conducting rated for 168 hours. This rating is required
The maximum temperature at which a Thermal Cutoff can be maintained for 10 minutes without
Maximum temp. limit(Tm):
re-closing. This rating is required by safety standards based on IEC60691.
Rated current(Ir): The allowable maximum current which a Thermal Cutoff is able to carry.
Size:(mm) (P-5A-F)
a b c d e
The temperature at which a Thermal Cutoff changes its state of conductivity to open circuit detection
Rated functioning temp.(Tf): current. The tolerance according to IEC60691 is from +0 to -10degC. (With Japan Electrical Appliance
and Material Law, on the other hand, they must function in the tolerance range of +/-7degC)
The fusing-off temperature indicates value measured in silicon oil with a temperature increased
Fusing-off temperature:
by 0.5-1degC per minute and a detective current 100mA or less.
The maximum temperature at which a Thermal Cutoff will not cause a change in state of conductivity
Holding temperature(Th): to open circuit while conducting rated for 168 hours. This rating is required by safety standards
based on IEC60691.
The maximum temperature at which a Thermal Cutoff can be maintained for 10 minutes without
Maximum temp. limit(Tm):
re-closing. This rating is required by safety standards based on IEC60691.
Rated current(Ir): The allowable maximum current which a Thermal Cutoff is able to carry.
Rated voltage(Ur): The allowable maximum voltage which a Thermal Cutoff is able to be applied.
○ PENDING;● APPROVAL
The fusing-off temperature indicates value measured in silicon oil with a temperature increased
Fusing-off temperature:
by 0.5-1degC per minute and a detective current 100mA or less.
The maximum temperature at which a Thermal Cutoff will not cause a change in state of conductivity
Holding temperature(Th): to open circuit while conducting rated for 168 hours. This rating is required by safety standards
based on IEC60691.
The maximum temperature at which a Thermal Cutoff can be maintained for 10 minutes without re-closing.
Maximum temp. limit(Tm):
This rating is required by safety standards based on IEC60691.
Rated current(Ir): The allowable maximum current which a Thermal Cutoff is able to carry.
Rated voltage(Ur): The allowable maximum voltage which a Thermal Cutoff is able to be applied.