Professional Documents
Culture Documents
S-Hold Tape
Self Fusing
Airtight & Waterproof Seal
Temperature range of use -50 °C to +260 °C
Insulates upto 12,000 volts
Can be used in water
UV resistant
Good resistance to fuels
Moisture Resistant
Can conform to any shape
Suggested Applications:
Automotive
Electrical
Cable & Wire Harness
Plumbing
Sealing Water leaks
Fire Hoses
Insulations
Above information is based on our present state of knowledge and is intended to provide general notes on our
products and their uses. it should not therefore be construed as guaranteeing specific properties of the products
described or their suitability for a particular application. You should thoroughly and independently test for any
planned application.
________________________________________________________________________________________________________
Above information is based on our present state of knowledge and is intended to provide general notes on our
products and their uses. it should not therefore be construed as guaranteeing specific properties of the products
described or their suitability for a particular application. You should thoroughly and independently test for any
planned application.
________________________________________________________________________________________________________
Electrical Use
Automotive
Above information is based on our present state of knowledge and is intended to provide general notes on our
products and their uses. it should not therefore be construed as guaranteeing specific properties of the products
described or their suitability for a particular application. You should thoroughly and independently test for any
planned application.
________________________________________________________________________________________________________
Method of Application
1) General Application
Apply the tape on the surface of application and stretch it to approximately 150%.
Overwrap 100% for first layer.
Apply the tape in spiral winding form with 50% overlap except at the end.
At ends have 100% overlap so that the tapes fuse with each other. The last end of the tape (approx
10 mm) should stretched very little and should have 100% overlap over silicon rubber tape’s last
spiral lap.
Once applied, the tape will take max 24 hrs to fuse with itself.
S-Hold Tape can be applied over any surface or pipe material, and even over a wet, dirty, greasy or
oily pipe.
S-Hold Tape can be applied UNDER WATER for submerged pipe repairs.
S-Hold Tape is heat resistant to 500F Degrees (260C); repairs can be made while pipe is hot.
S-Hold Tape fuses in minutes or even SECONDS, enabling you to repair pipes FAST and minimize
downtime.
S-Hold Tape can be easily removed by cutting, further minimizing downtime when a permanent pipe
repair is being made.
S-Hold Tape can be your quick “first response” pipe repair solution while alternative permanent
repairs can be planned.
1.) Wrap S-Hold Tape pipe repair tape around leaking pipe by stretching and overlapping onto
itself. Stretch at least double to ensure a good bond; for high pressure leaks stretch to
maximum amount. The tighter S-Hold Tape is wrapped, the quicker and stronger the bond.
2.) Continue wrapping S-Hold Tape around pipe by overlapping 50% onto itself so that ½ the
width is covered with the next wrap. The first and last wrap should completely (100%)
overlap onto the previous wrap for a complete bond. Additional layers may be necessary to
repair the leak, and the same process should be used over the previous layers. S-Hold Tape
works on either side. The more S-Hold Tape that is wrapped around the pipe, the stronger
the pipe repair.
3.) Repositioning S-Hold Tape is only appropriate in the first few seconds after wrapping.
Attempting to reposition S-Hold Tape after 1 minute or longer is not recommended. S-Hold
Tape is not reusable; however, additional S-Hold Tape can be applied over project at any
time in the future.
in each direction away from the leak; however, additional strength can be added simply by
wrapping more S-Hold Tape. In addition, the larger the pipe diameter, the more repair tape
will be required. Wrap S-Hold Tape further in each direction from the leak on larger
diameter pipes and hoses.
S-Hold Tape Pipe Repair has essentially a “maximum” stretch. It is important to stretch S-Hold Tape to its
maximum to avoid having the leak create a bubble.
Above information is based on our present state of knowledge and is intended to provide general notes on our
products and their uses. it should not therefore be construed as guaranteeing specific properties of the products
described or their suitability for a particular application. You should thoroughly and independently test for any
planned application.