Professional Documents
Culture Documents
Installation of antenna:
Screw the SMA female pin of the WIFI antenna to the male SMA interface
of the router with sign “WIFI”.
Warning: The antennas must be screwed tightly, or the signal quality of
antenna will be influenced!
Installation of cable:
Insert one end of the network cable into the switch interface with sign “Local
Network”, and insert the other end into the Ethernet interface of user’s device.
The signal connection of network direct cable is as follows:
The “Welcome” page will give some contact information, if you have any
question or problem, please contact us.
Start a web browser and type 192.168.1.1 in the Address (URL) field (The
Default IP Address of the Ethernet port is 192.168.1.1). It will prompt a login
page. The default username and password are both “admin”. Please input the
username and password login to access the configuration pages.
MTU: the size of the largest protocol data unit that the layer can pass onwards.
MAC Clone: Set the MAC address filled to wide area network. If you click
“Auto Fill”, the MAC address of the PC connected with is entered.
Profile List: Parameter list of 3G.
UserName: username used to login your ISP(Internet Service Provider) 3.3.3 Lan Settings
Password: password used to login your ISP You may enable/disable networking functions and configure their
Call Center: The dial number of your ISP parameters as your wish.
APN: The access point name of your ISP
Auth Mode: you have to choose the auth mode if the server to which you are
connecting requires PAP or CHAP authentication.
Keep Alive: Set up the redial period after the disconnection.
On demand Mode: If there is no communication for the specified time, it will
disconnect the connection automatically.
Add:J1-J2,3rd Floor,No.44,GuanRi Road, Software Park, XiaMen, China 9 Zip Code:361008
Tel:+86 592-6300320, +86 592-6300321, +86 592-6300322 Fax:+86 592-5912735 http://www.four-faith.com/e_index.asp
Xiamen Four-Faith Communication Technology Co., Ltd.
DHCP Settings: This setting controls whether TCP/IP should use DHCP to
automatically assign an IP address, or statically assigned an IP address.
Starting IP Address: The starting IP Address of the DHCP server’s Address pool
Ending IP Address: The ending IP Address of the DHCP server’s Address pool
Statically Assigned: Assign the static IP address to the specified MAC address.
LAN IP Address Setting: Set the LAN port IP Address. You can establish two 802.1d spanning tree: the basic function of STP is to prevent bridge loops and
LAN areas by edit LAN2 IP Address. ensuing broadcast radiation.
UPNP: Universal Plug and Play (UPnP) is a set of networking protocols for
primarily residential networks without expert administrators that permits
networked devices.
DNS Proxy: The DNS proxy enables clients to send DNS queries and then
relays those queries to the current public network DNS server.
3.4.1 Basic
You could configure the minimum number of Wireless settings for
communication, such as Network Name (SSID) and Channel. The Access Point
Add:J1-J2,3rd Floor,No.44,GuanRi Road, Software Park, XiaMen, China 11 Zip Code:361008
Tel:+86 592-6300320, +86 592-6300321, +86 592-6300322 Fax:+86 592-5912735 http://www.four-faith.com/e_index.asp
Xiamen Four-Faith Communication Technology Co., Ltd.
Decline BA Request: Select to reject peer BA-Request or not. Data Beacon Rate(DTIM): The DTIM period indicates how many beacon
frames can be transmited before another DTIM is transmitted.
3.4.2 Advanced Fragment Threshold: The maximum frame size wireless device can transmit
Use the Advanced Setup page to make detailed settings for the Wireless. without frangmenting the frame.
Advanced Setup includes items that are not available from the Basic Setup RTS Threshold: Specify the packet size of an RTS(request-to-send)
page, such as Beacon Interval and Control Tx Rates. transmission. This help control tranffic flow through an access point,
especially one with many clients.
TX Power: TX Power measurement.
Short Preamble: A signal used to synchronize the transmitting timing including
Synchronization and Start Frame Delimiter.
Short Slot: The amount of time a device waits after a collision before
retransmitting a packet. Throughput on 802.11g can be increased by
enabling short slot tme. Slort slot tme is an 802.11g-only feature.
Tx Burst: The device will try to send a serial of packages with single ACK reply
from the clients. Enable the transmitted time slot can increase transmission
throughput.
Pkt_Aggregate: The parameter can be used to aggregate multiple packets and
increase the delivered bandwidth in community networks.
Country Code: The settings control the channels the card can operate on, as
well as maximum transmission power.
WMM Parameters: Click “WMM Configuration” to setup the WMM function. secret key.
Access category WMM defines 4 access categories(Voice, Video, Best WPA,WPA-PSK,WPA2,WPA2-PSK,WPA-PSK/WPA2-PSK, and
Effort, Background). These categories comply with preferred traffic level, WPA1/WPA2: WPA offers three encryption methods, TKIP, AES.
and are mapped to the IEEE802.11d preferred tag. Encryption Type: If select Open&Shared authentication mode, the selection of
encryption type are None and WEP.
WPA Algorithms: If select WPA Algorithms, the selection of encryption type are
TKIP and AES.
Multicast-to-Unicast: Convert Multicast data to Unicast one. WEB keys: When using WEP encryption algorithm, it will be valid. The key must
match with two formats----26 Hex characters or 13 ASCII characters.
3.4.3 Security
Setup the wireless security and encryption to prevent from unauthorized
access and monitoring.
Policy: Set up MAC address filter rule for the specified wireless LAN device.
Add a station Mac: Enter the MAC address of the wireless LAN device for MAC
address filtering.
Security Mode: Enable security mode could prevent any unauthorized access
to your wireless network.
Open: The wireless will need to set to the same authentication type(Open).
Shared: Share key is when both the sender and the recipient share a
Add:J1-J2,3rd Floor,No.44,GuanRi Road, Software Park, XiaMen, China 14 Zip Code:361008
Tel:+86 592-6300320, +86 592-6300321, +86 592-6300322 Fax:+86 592-5912735 http://www.four-faith.com/e_index.asp
Xiamen Four-Faith Communication Technology Co., Ltd.
MAC/IP/Port Filtering: All list from the filtering will become invalid while disable You may setup Virtual Servers to provide services on Internet.
this function.
Default Policy: Drop or accept the packet that don’t match with any rules in all
list from the filtering.
DMZ IP Address: The IP of user outside which gets direct access to a server
that has has company data.
Webs Content Filter: Set up the web content filter which will deny client from
access to the internet by contented those options you checked.
Remote management: Enable/Disable access the web server via WAN side.
Ping from WAN Filter: Enable/Disable the ping response to the WAN side.
SPI Firewall: Enable/Disable a firewall that keeps track of the state of network
connections travelling across it. Add a URL filter: Block up the web-sites access according URL Filtere String.
System Reboot: Router will reboot after about one minute while click “Reboot”.
WEB Port: If set up the port of web server, you must fill the port in the web-site
when access the router.
Add a Host filter:Block up the web-sites access according the web host name.
3.6.1 Management
You may configure administrator account and password, NTP settings, and
Dynamic DNS settings here.
Current Time: Display the current time. Synchronize the time with PC while click
“Sync with host”.
Time Zone: Select the time zone at your local time.
NTP Server: Input the IP address or the host name of the time server. Make
Select Language: Select the language you want. sure the server work well.
NTP synchronization: Set the synchronization interval.
Dynamic DNS Provider: Before setting up dynamic DNS server, you must finish
registration of the Dynamic DNS server in
“Dyndns.org”,”freedns.afraid.org”,”www.zoneedit.com” or
“www.no-ip.com”.
Account: Input the user name provided by provider.
Password: Input the password provided by provider.
DDNS: Input the host name promted by provider.
Click “Refresh” to update the information of system. Click “Clear” to clear the
system log information.
upload upgrade flash and be patient please. Caution! A corrupted image will hang up Default”.
the system.