Professional Documents
Culture Documents
General Safety Rules TOOL USE AND CARE 7. If the tool stalls, release the trigger immediately, reverse the direction of rotation and
slowly squeeze trigger to back out the bit.
* Do not force the power tool. Use the correct power tool for your application. The correct
power tool will do the job better and safer at the rate for which it was designed. 8. To protect the battery and charger, do not charge battery when temperature is BELOW
WARNING! * Do not use the power tool if the switch does not turn it on and off. Any power tool that 50ºF (10ºC) or ABOVE 104ºF (40ºC). Do not store the tool and battery pack in locations
4.8V Rechargeable Cordless Screwdriver Read all instructions. Failure to follow all instructions listed
below may result in electric shock, fire and/or serious injury.
cannot be controlled with the switch is dangerous and must be repaired.
* Disconnect the plug from the power source and/or the battery pack from the power tool
where the temperature may reach or exceed 122ºF (50ºC).
9. Do not disassemble charger or operate the charger if it has received a sharp blow, been
dropped or otherwise damaged in any way. Replace damaged cord or plugs
Instruction Manual The term "power tool" in all of the warnings listed below
before making any adjustments, changing accessories or storing power tools. Such
preventative safety measures reduce the risk of starting the power tool accidentally.
immediately. Incorrect reassembly or damage may result in electric shock or fire.
refers to your battery-operated (cordless) power tool. * Store idle power tools out of the reach of children and do not allow persons unfamiliar
with the power tool or these instructions to operate the power tool. Power tools are
dangerous in the hands of untrained users. The label on your tool may include the following symbols.
SAVE THESE INSTRUCTIONS * Maintain power tools. Check for misalignment or binding of moving parts, breakage of
parts and any other condition that may affect the power tools operation. If damaged, V....................volts A................amperes
WORK AREA SAFETY have the power tool repaired before use. Many accidents are caused by poorly Hz..................hertz W...............watts
* Keep work area clean and well lit. Cluttered or dark areas invite accidents. maintained power tools.
min................minutes ...............alternating current
* Do not operate power tools in explosive atmospheres, such as in the presence of * Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting
flammable liquids, gases or dust. Power tools create sparks which may ignite the dust or edges are less likely to bind and are easier to control. ................direct current ...............Class ll Construction
fumes. * Use the power tool, accessories and tool bits etc., in accordance with these instructions ...................earthing terminal .../min..........revolutions or reciprocations per minute
* Keep children and bystanders away while operating a power tool. Distractions can cause and in the manner intended for the particular type of power tool, taking into account the
you to lose control. working conditions and the work to be performed. Use of the power tool for operations
different from those intended could result in a hazardous situation.
Please recycle this rechargeable battery once it is no longer usable. Call the
ELECTRICAL SAFETY Rechargeable Battery Recycling Center (800) 822-8837 for instructions on
* Power tool plugs must match the outlet. Never modify the plug in any way. Do not use SERVICE
any adapter plugs with earthed (grounded) power tools. Unmodified plugs and matching * Have your power tool serviced by a qualified repair person using only identical where and how to recycle Ni-Cd batteries. Never dispose of Ni-Cd
outlets will reduce risk of electric shock. replacement parts. This will ensure that the safety of the power tool is maintained. batteries in land fills. Never dispose of Ni-Cd batteries in open flames as
* Avoid body contact with earthed or grounded surfaces such as pipes, radiators, ranges the batteries may explode. Never dispose of Ni-Cd batteries
and refrigerators. There is an increased risk of electric shock if your body is earthed or WARNING: Some dust created by power sanding, sawing, grinding, drilling and other in streams, rivers, lakes or the ocean. Always dispose of Ni-Cd batteries
grounded. construction activities contains chemicals known to cause cancer, birth defects or other according to the disposal instructions of the RBRC as above.
* Do not expose power tools to rain or wet conditions. Water entering a power tool will reproductive harm. Some examples of these chemicals are:
increase the risk of electric shock.
* Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the power * Lead from lead-based paints,
tool. Keep cord away from heat, oil, sharp edges or moving parts. Damaged or * Crystalline silica from bricks and cement and other masonry products, and Technical Specifications
entangled cords increase the risk of electric shock. * Arsenic and chromium from chemically-treated lumber.
* When operating a power tool outdoors, use an extension cord suitable for outdoor use. Product Designation 4.8 Volt Cordless Screwdriver
Use of a cord suitable for outdoor use reduces the risk of electric shock. Your risk from these exposures varies, depending on how often you do this type of work. To No Load Speed, Max. 200/min.
reduce your exposure to these chemicals work in a well-ventilated area, and work with Screw Diameter, Max. 3/16 in. (5mm)
PERSONAL SAFETY approved safety equipment, such as those dust masks that are specially designed to filter Bit Size 1/4 in. (6mm) Hex Collet
* Stay alert, watch what you are doing and use common sense when operating a power out microscopic particles.
tool. Do not use a power tool while you are tired or under the influence of drugs, alcohol
or medications. A moment of inattention while operating power tools may result in
serious personal injury. SPECIFIC SAFETY RULES
* Use safety equipment. Always wear eye protection. Safety equipment such as dust mask, 1. Do not open the battery yourself. There is danger of a short circuit.
Battery
non-skid safety shoes, hard hat, or hearing protection used for appropriate conditions 2. Only connect the charger to a 120V AC power supply. Voltage 4.8V DC
will reduce personal injuries. 3. Keep the tool away from other metal objects like: paper clips, coins, keys, nails, screws or Type Ni-Cd
* Avoid accidental starting. Ensure the switch is in the off-position before plugging in. other small metal objects that can make a connection between the two terminals located
Carrying power tools with your finger on the switch or plugging in power tools that have Capacity 700 mAh
at the bottom of the tool handle. Shorting the battery terminals together may cause
Distributed By:
the switch on invites accidents. sparks, burns, or a fire.
Apollo Tools, Ltd. * Remove any adjusting key or wrench before turning the power tool on. A wrench or a key
255 Clapp Road - Suite 200 left attached to a rotating part of the power tool may result in personal injury. 4. Before screwing into a wall, check with a metal / voltage detector to be sure you are not
Scituate, MA 02066 * Do not overreach. Keep proper footing and balance at all times. This enables better driving into an electricity, gas or water supply line. Charger
USA 5. Do not use dull or damaged bits and accessories. Dull or damaged bits have a greater
control of the power tool in unexpected situations. Type 120V AC 60Hz, UL listed
Visit our website at: www.apollotools.com * Dress properly. Do not wear loose clothing or jewelery. Keep your hair, clothing and tendency to bind in the workpiece.
Contact us at: sales.usa@apollotools.com gloves away from moving parts. Loose clothes, jewelery or long hair can be caught in 6. Secure the material being worked on. Never hold it in your hand or across legs. Unstable Charging Time, Approx. 4~6 hrs
Or phone us at: 1-866-591-4749
International Sales: sales@apollotools.com moving parts. support can cause the driver bit to bind causing loss of control and injury.
Made in China
1 2 3
Household 4.8V Rechargeable Cordless Screwdriver Instruction Manual Household 4.8V Rechargeable Cordless Screwdriver Instruction Manual
4 5 6