Professional Documents
Culture Documents
SQUER Ventilation Ducts and Fittings Alnor PDF
SQUER Ventilation Ducts and Fittings Alnor PDF
Download AlnorCAM
B2B ordering
Rectangular ducts
and fittings
864
ALNOR® ventilation systems
is a registered trademark protected by a technical patent. All modification rights reserved.
SQUER
TECHNICAL INFORMATION
This is ALNOR's range of rectangular ducts and fittings for Limit values
ventilation systems. of static pressure (ps) Pa
Duct air Leakage rate
This catalogue presents the rectangular ducts and fittings tightness limit value Vacuum pres- Overpressure in
sized in accordance with EN 1505:2001, “Ventilation for class (fmax) m3s-1m -2 sure in each each class
buildings. Sheet metal air ducts and fittings with rectangular class 1 2 3
cross-section. Dimensions” and reference standards. A 0.027 × ptest0.65 × 10 -3 200 400
The surface area of ventilation ducts and fittings is measured
B 0.009 × ptest0.65 × 10 -3 500 400 1000 2000
according to DIN 18379, “German construction contract
procedures – Part C: General technical specifications for C 0.003 × ptest0.65 × 10 -3 750 400 1000 2000
building works – Room ventilation systems”. Rectangular D* 0.001 × ptest0.65 × 10 -3 750 400 1000 2000
ducts and fittings are designed for low- and medium-pressure Special-purpose ventilation ducts
indoor HVAC systems. Rectangular ducts and fittings made
from stainless steel or aluminium are available on request
if a higher corrosion protection level is required. Alnor also
fabricates custom fittings to individual design requirements. Design
Rectangular ducts and fittings are fabricated from metal sheets
which are hemmed and seamed, pressure-welded, or riveted.
The ducts and fittings are available in low- and medium-
Dimensions pressure versions (min. vacuum / max. overpressure):
class N design (low-pressure design):
The nominal size is a conventional dimension used to designate standard design from -400 Pa to +1000 Pa
and calculate straight ducts and fittings. It is the internal class S design (medium-pressure design):
dimension of sides a and b, where side a is exposed to view from -1000 Pa to 2500 Pa
(see Fig. 1). The length sizes of the sides at a smaller end of
an adapter fitting are designated c and d, where side c is The dimensional tolerances and metal sheet thickness are
exposed to view. selected according to the following criteria:
Dimension L is the effective length of a straight duct, which length of the long side of a straight duct,
is added to the overall length of the ductwork system. the dimension of the longest side of the connection cross-
Dimension l is the effective length of a fitting, which is added section
to the overall length of the ductwork system. of the fitting.
Dimension of
a
a
c
865
ALNOR® ventilation systems
is a registered trademark protected by a technical patent. All modification rights reserved.
SQUER
TECHNICAL INFORMATION
Rectangular ducts and fittings
Side length
100 150 200 250 300 400 500 600 800 1000 1200
(mm)
200 0.02 0.03 0.04 Ac
133 171 200 dh
149 186 218 de
0.6 0.7 0.8 Al
250 0.025 0.038 0.05 0.063 Ac
143 188 222 250 dh
165 206 241 273 de
0.7 0.8 0.9 1 Al
300 0.03 0.045 0.06 0.075 0.09 Ac
150 200 240 273 300 dh
180 224 262 296 327 de
0.3 0.9 1 1.1 1.2 Al
400 0.04 0.06 0.08 0.1 0.12 0.16 Ac
160 218 267 308 343 400 dh
205 255 299 337 373 436 de
1 1.1 1.2 1.3 1.4 1.6 Al
500 0.075 0.1 0.13 0.15 0.2 0.25 Ac
231 286 333 375 444 500 dh
283 331 374 413 483 545 de
1.3 1.4 1.5 1.6 1.8 2 Al
600 0.09 0.12 0.15 0.18 0.24 0.3 0.36 Ac
240 300 353 400 480 545 600 dh
307 359 406 448 524 592 654 de
1.5 1.6 1.7 1.8 2 2.2 2.4 Al
800 0.16 0.2 0.24 0.32 0.4 0.48 0.64 Ac
320 381 436 533 615 686 800 dh
410 463 511 598 675 745 872 de
2 2.1 2.2 2.4 2.6 2.8 3.2 Al
866
ALNOR® ventilation systems
is a registered trademark protected by a technical patent. All modification rights reserved.
SQUER
TECHNICAL INFORMATION
Side length
100 150 200 250 300 400 500 600 800 1000 1200
(mm)
1000 0.25 0.3 0.4 0.5 0.6 0.8 1 Ac
400 462 571 667 750 889 1000 dh
512 566 662 747 825 965 1090 de
2.5 2.6 2.8 3 3.2 3.6 4 Al
1200 0.36 0.48 0.6 0.72 0.96 1.2 1.44 Ac
480 600 706 800 960 1091 1200 dh
614 719 812 896 1049 1184 1308 de
3 3.2 3.4 3.6 4 4.4 4.8 Al
1400 0.56 0.7 0.84 1.12 1.4 1.68 Ac
622 737 840 1018 1167 1292 dh
771 871 962 1125 1270 1403 de
3.6 3.8 4 4.4 4.8 5.2 Al
1600 0.64 0.8 0.96 1.28 1.6 1.92 Ac
640 762 873 1067 1231 1371 dh
819 925 1022 1195 1350 1491 de
4 4.2 4.4 4.8 5.2 5.6 Al
1800 0.9 1.08 1.44 1.8 2.16 Ac
783 900 1108 1286 1440 dh
976 1078 1261 1424 1573 de
4.6 4.8 5.2 5.6 6 Al
2000 1 1.2 1.6 2 2.4 Ac
800 923 1143 1333 1500 dh
1024 1131 1323 1494 1650 de
5 5.2 5.6 6 6.4 Al
867
ALNOR® ventilation systems
is a registered trademark protected by a technical patent. All modification rights reserved.
SQUER
TECHNICAL INFORMATION
Rectangular ducts and fittings
Rigidity of connection
Rectangular ducts and fittings are braced by transverse The ventilation duct connections are fabricated in accordance
embossing of the metal sheet. with PN-B-76002 “Ventilation. Connections of ventilation
The ducts are additionally braced with galvanized baffle/strut equipment, ducts and fittings made of metal sheets”.
tubes as shown in Fig. 2. Rectangular ducts are connected to ventilation equipment
using frames made of sheet angles and corner straps.
The sheet angle size depends on the side length of the
rectangular duct.
The rules for using sheet angle frames in rectangular ducts
and fittings are shown in Table 5.
a
l
b Table 5
l
b
Rules for using sheet angle frames in ventilation rectangular
ducts and fittings in the standard version with galvanized
Fig. 2. steel sheet
Corner straps and sheet angles are made air-tight using sealants.
A B L
Number of braces
(mm) (mm) (mm) Stainless steel sheet angles and corner straps are the standard
<1000 <1000 <1000 0 accessories for stainless steel ducts and fittings. Aluminium
<1000 >1000 <1000 1 angles and corner straps are the standard accessories for
aluminium ducts and fittings.
<1000 1000-1500 <1000 2 The rules for using sheet angle frames in rectangular ducts
<1000 1500-2000 1500-2000 4 and fittings are shown in Table 6.
1000-1500 1000-1500 <1000 1 cross brace
Table 6
1000-1500 1000-1500 1000-1500 2 cross braces
Rules for using sheet angle frames in standard ventilation
rectangular ducts and fittings made from stainless steel or
Bends and elbows are braced with vanes according to EN aluminium sheet
1505, “Ventilation for buildings. Sheet metal air ducts and
fittings with rectangular cross-section. Dimensions”. Side length (mm) ≤ 1000 > 1000 > 2500
Elbows are recommended for low air velocity and/or low-
Sheet angle size (mm) PQ20 PQ30 PQ30
pressure ventilation systems and smaller sizes of side a ≤
400 mm.
Bends and elbows set at ≤ 45˚ require no vanes. Table 7
The vane alignment is shown in Table 7 and Fig. 3. The vane alignment is according to EN 1505, “Ventilation for
buildings. Sheet metal air ducts and fittings with rectangular
cross-section. Dimensions”.
The surface area of rectangular ducts is measured according to > 400 ≤ 800 1 a/3
DIN 18379, “German construction contract procedures – Part > 800 ≤ 1600 2 a/4 a/2
C: General technical specifications for building works – Room
> 1600 ≤ 2000 3 a/8 a/3 a/2
ventilation systems”.
T h e d u c t s w i t h a s u r f a c e a r e a < 1. 0 m2
are calculated as 1.0 m2 fittings.
T h e f i t t i n g s w i t h a s u r f a c e a r e a < 1. 0
m2
are calculated as 1.0 m2 fittings.
a
a3
a2
a1
r>100m m
Fig. 3.
868
ALNOR® ventilation systems
is a registered trademark protected by a technical patent. All modification rights reserved.
SQUER
TECHNICAL INFORMATION
AlnorCAM is a software suite designed for selecting • minimizes errors in the processing of engineering
rectangular components for ventilation ductwork. documentation,
AlnorCAM provides a full summary of selected ventilation • significantly reduces fabrication lead times while
ductwork components, including the number of ducts and maintaining competitive pricing and quality,
fittings to be ordered plus their surface areas in square • precision, reliability and flexibility: you always know how
metres and fabrication models. The programme reduces the many metres of ductwork are needed, which helps to
time to fabricate a ready-to-use ventilation ductwork system avoid confusion on site,
and helps eliminate errors due to inaccurate dimensioning. • maximum benefits when AlnorCAM is used for B2B
Ducts and fittings plotted in AlnorCAM are displayed in ordering
the form of 3D models and engineering drawings. The • AlnorCAM is a freeware design suite.
programme automatically calculates the surface areas of • Available in Polish and English
ducts and fittings, including the required quantity of thermal
insulation if included in the design. The automatically
generated summary saves time and makes normal designing
and calculation work much easier.
An extensive product database includes insulated and pre-
insulated ductwork components. The programme also Download and install
calculates the required quantity of mineral wool for insulated AlnorCAM
ducts and fittings. Three thermal insulation thickness sizes
are available: 30, 50 and 100 mm.
Additionally, the cladding and inner ducts can be made
from different materials as required (galvanized steel sheet,
aluminium sheet, or stainless steel sheet).
869
ALNOR® ventilation systems
is a registered trademark protected by a technical patent. All modification rights reserved.
Rectangular ducts
QDN
Rectangular ducts and fittings
Dimensions
Description
All rectangular ducts are fitted with flange frames made of
sheet angles and braced by cross-wise ribbing. Larger ducts
are additionally braced with galvanized tubes (baffles). The
ducts are manufactured in the following standard sections
to standardize the fabrication, shipping and installation
procedure:
If a or b ≤ 500, then L = 1250 mm
If a or b > 500, then L = 1500 mm
type
N
S
OCY
KWS
ALU
a
b
l
N — low-pressure version
S — medium-pressure version
C — galvanized steel
K — stainless steel
A — aluminium
a — width
b — height
l — length
870
ALNOR® ventilation systems
is a registered trademark protected by a technical patent. All modification rights reserved.
Angle rectangular ducts spigot plates
QD1
Description
The angle rectangular duct spigot plates are tipped with
sheet angles at one end. The other end features a spigot
plate similar to a roof kerb, the size of which can be chosen
according to individual requirements. The duct angle to the
plate can be anywhere between 10 and 90 degrees according
to individual requirements.
type
N
S
OCY
KWS
ALU
a
b
l
α
e
f
N — low-pressure version
S — medium-pressure version
OCY — galvanized steel
KWS — stainless steel
ALU — aluminium
a — width
b — height
l — length
α — angle
e — base dimension a
f — base dimension b
871
ALNOR® ventilation systems
is a registered trademark protected by a technical patent. All modification rights reserved.
Rectangular elbows
QBF
Rectangular ducts and fittings
Dimensions
Description
The 90˚ elbows are fitted with sheet angles, and the entire
product is braced by cross-wise ribbing.
The elbows are recommended for low air velocity and/or
low-pressure ventilation systems and smaller sizes of side b
≤ 400 mm. The standard radius is r = 120 mm.
Typical applications of the elbows include rerouting the
ductwork by 90 degrees with the same clear cross-section.
type
N N — low-pressure version
S S — medium-pressure version
OCY OCY — galvanized steel
KWS KWS — stainless steel
ALU ALU — aluminium
a a — width
b b — height
e e — extension (default e = 150 mm)
f f — extension (default f = 150 mm)
r r — radius (default r = 120 mm)
872
ALNOR® ventilation systems
is a registered trademark protected by a technical patent. All modification rights reserved.
Variable clearance elbows
QBFR
Description
The 90˚ elbows are fitted with sheet angles, and the entire
product is braced by cross-wise ribbing.
The elbows are recommended for low air velocity and/or
low-pressure ventilation systems and smaller sizes of side b
≤ 400 mm.
The standard radius is r = 120 mm.
Typical applications of the elbows include rerouting the
ductwork by 90 degrees with the inner clearance varying
along the elbow path.
type
N N — low-pressure version
S S — medium-pressure version
OCY OCY — galvanized steel
KWS KWS — stainless steel
ALU ALU — aluminium
a a — width
b b — height
d d — outlet height
e e — extension (default e = 150 mm)
f f — extension (default f = 150 mm)
r r — radius (default r = 120 mm)
873
ALNOR® ventilation systems
is a registered trademark protected by a technical patent. All modification rights reserved.
Rectangular bends
QB
Rectangular ducts and fittings
Dimensions
Description
The standard 90˚ bends are fitted with sheet angles, have an
inner and outer rounding, and the entire product is braced
by cross-wise ribbing.
The bends are recommended for high air velocity and/or
higher pressure ventilation systems and greater sizes of side
b > 400 mm.
The standard radius is r = 120 mm. The standard angle is a = 90˚.
Typical applications of the bends include rerouting the
ductwork by 90˚ with the same clear cross-section.
type
N N — low-pressure version
S S — medium-pressure version
OCY OCY — galvanized steel
KWS KWS — stainless steel
ALU ALU — aluminium
a a — width
b b — height
e e — extension (default e = 30 mm)
f f — extension (default f = 30 mm)
r r — radius (default r = 120 mm)
α α — angle (default α = 90˚)
874
ALNOR® ventilation systems
is a registered trademark protected by a technical patent. All modification rights reserved.
Variable clearance bends
QBR
Description
The standard 90˚ bends are fitted with sheet angles,
have an inner and outer rounding, and the entire
product is braced by cross-wise ribbing. The bends are
recommended for high air velocity and/or higher pressure
ventilation systems and greater sizes of side b > 400 mm.
The standard radius is r = 120 mm. The standard angle is
a = 90˚. Typical applications of the elbows include rerouting
the ductwork by 90 degrees with the inner clearance varying
along the elbow path.
875
ALNOR® ventilation systems
is a registered trademark protected by a technical patent. All modification rights reserved.
Diffuser bends
QBR1
Rectangular ducts and fittings
Dimensions
Description
The standard 90˚ bends are fitted with sheet angles, have an
inner and outer rounding, and the entire product is braced
by cross-wise ribbing. The bends are recommended for high
air velocity and/or higher pressure ventilation systems and
greater sizes of side a > 400 mm.
The standard radius is r = 120 mm. The standard angle is a = 90˚.
Typical applications of the bends include rerouting the
ductwork by 90 degrees with the inner clearance varying in
two planes along the bend path. A diffuser bend does not
require vanes. The product can feature additional bracing
with baffles on request.
876
ALNOR® ventilation systems
is a registered trademark protected by a technical patent. All modification rights reserved.
Eccentric reducers
QPR2
Description
The eccentric reducers are adapters designed for coupling
two rectangular ducts of different sizes.
The ends are fitted with sheet angles, and the entire fitting
is braced by cross-wise ribbing.
The eccentric reducers help route the ventilation ductwork
with liberal modifications of all duct dimensions and offsetting
the centreline by any value in both directions.
type
N N — low-pressure version
S S — medium-pressure version
OCY OCY — galvanized steel
KWS KWS — stainless steel
ALU ALU — aluminium
a a — width
b b — height
c c — outlet width
d d — outlet height
e e — vertical offset
f f — horizontal offset
h h — extension (default h = 30 mm)
m m — extension (default m = 30 mm)
l l — length
877
ALNOR® ventilation systems
is a registered trademark protected by a technical patent. All modification rights reserved.
Eccentric square-to-round transitions
PR7/ PRL7
Rectangular ducts and fittings
Dimensions
Description
This transition piece changes the ductwork shape from
rectangular to round.
The fitting helps route the ventilation ductwork with liberal
modifications of all duct dimensions and offsetting the
centreline by any value in both directions.
The round connector is male in the standard version.
The PRL7 fittings have a male connector fitted with a gasket.
878
ALNOR® ventilation systems
is a registered trademark protected by a technical patent. All modification rights reserved.
Concentric reducers
QPR6
Description
The reducers are adapters designed for coupling two
rectangular ducts of different sizes.
The ends are fitted with sheet angles, and the entire fitting
is braced by cross-wise ribbing.
The reducers help in routing ductwork at points where a
symmetric cross-section reduction is required. The ducts are
kept coaxial at both ends.
type
N N — low-pressure version
S S — medium-pressure version
OCY OCY — galvanized steel
KWS KWS — stainless steel
ALU ALU — aluminium
a a — width
b b — height
c c — inlet clear width
d d — inlet height
h h — extension (default h = 30 mm)
m m — extension (default m = 30 mm)
l l — length
879
ALNOR® ventilation systems
is a registered trademark protected by a technical patent. All modification rights reserved.
Concentric square-to-round transitions
PR1 / PRL1
Rectangular ducts and fittings
Dimensions
Description
This transition piece changes the ductwork shape from square
to round.
This fitting helps in routing round and rectangular ducts with
the centrelines aligned.
The square connector has a flange frame in the standard
version.
The round connector is male in the standard version.
The PRL1 fittings have a male connector fitted with a gasket.
880
ALNOR® ventilation systems
is a registered trademark protected by a technical patent. All modification rights reserved.
Offsets
QPR3
Description
Offsets help bypassing obstacles along the ductwork route,
e.g. at intersections of two ducts.
The ends are fitted with sheet angles, and the entire fitting
is braced by cross-wise ribbing.
To achieve the required air flow rate, appropriate length sizes
l and offset sizes e should be used.
type
N N — low-pressure version
S S — medium-pressure version
OCY OCY — galvanized steel
KWS KWS — stainless steel
ALU ALU — aluminium
a a — width
b b — height
e e — offset
h h — extension (default h = 30 mm)
m m — extension (default m = 30 mm)
l l — length
881
ALNOR® ventilation systems
is a registered trademark protected by a technical patent. All modification rights reserved.
Offsets
QPR4
Rectangular ducts and fittings
Dimensions
Description
Variable diameter offsets facilitate bypassing obstacles along
the ductwork route while changing the connected duct height,
which helps building intersections of two ducts. The ends
are fitted with sheet angles, and the entire fitting is braced
by cross-wise ribbing. To achieve the required air flow rate,
appropriate length sizes l and offset sizes e should be used.
type
N N — low-pressure version
S S — medium-pressure version
OCY OCY — galvanized steel
KWS KWS — stainless steel
ALU ALU — aluminium
a a — width
b b — height
d d — outlet height
e e — offset
h h — extension (default h = 30 mm)
m m — flange length (default m = 30 mm)
l l — length
882
ALNOR® ventilation systems
is a registered trademark protected by a technical patent. All modification rights reserved.
Equal T-pieces
TR
Description
The T-piece ends are fitted with sheet angles, and the entire
fitting is braced by cross-wise ribbing.
This fitting allows building ductwork with a branch taken
off at 90 degrees.
The T-piece height a is fixed.
type
N N — low-pressure version
S S — medium-pressure version
OCY OCY — galvanized steel
KWS KWS — stainless steel
ALU ALU — aluminium
a a — width
b b — height
d d — outlet height
h h — take-off height
i i — extension (default i = 30 mm)
j j — extension (default j = 30 mm)
p p — extension (default p = 30 mm)
q q — radius (default q = 120 mm)
r r — radius (default r = 120 mm)
883
ALNOR® ventilation systems
is a registered trademark protected by a technical patent. All modification rights reserved.
T-pieces with square take-off
TR1
Rectangular ducts and fittings
Dimensions
Description
The T-piece ends are fitted with sheet angles, and the entire
fitting is braced by cross-wise ribbing.
The T-piece helps building ductwork with a take-off branch
at 90 degrees and a reduced size. The inlet and outlet sizes
are the same.
type
N N — low-pressure version
S S — medium-pressure version
OCY OCY — galvanized steel
KWS KWS — stainless steel
ALU ALU — aluminium
a a — width
b b — height
l l — length
w w — take-off length
d d — take-off width
e e — take-off offset in length
f f — take-off offset in width
I3 I3 — take-off length (default I3 = 100 mm)
884
ALNOR® ventilation systems
is a registered trademark protected by a technical patent. All modification rights reserved.
Reducing T-pieces
TR7
e b a
i
r
h
q
j
a
Description
The T-piece ends are fitted with sheet angles, and the entire
fitting is braced by cross-wise ribbing.
The T-piece helps building ductwork with a take-off branch
at 90 degrees, reduction of the main duct clear passage and
an offset by any value of size m.
type
N N — low-pressure version
S S — medium-pressure version
OCY OCY — galvanized steel
KWS KWS — stainless steel
ALU ALU — aluminium
a a — width
b b — height
d d — outlet height
h h — take-off height
i i — extension (default i = 30 mm)
j j — extension (default j = 30 mm)
p p — extension (default p = 30 mm)
q q — radius (default q = 120 mm)
r r — radius (default r = 120 mm)
e e — offset
The standard versions are made in default dimension sizes which do not have to be specified.
885
ALNOR® ventilation systems
is a registered trademark protected by a technical patent. All modification rights reserved.
Concentric reducing T-pieces
TR8
Rectangular ducts and fittings
Dimensions
Description
The T-piece ends are fitted with sheet angles, and the entire
fitting is braced by cross-wise ribbing.
The T-piece helps building ductwork with a take-off branch
at 90 degrees, reduction of the main duct clear passage and
an offset by any value of size m.
The take-off can be fabricated with height other than that
of the T-piece.
type
N N — low-pressure version
S S — medium-pressure version
OCY OCY — galvanized steel
KWS KWS — stainless steel
ALU ALU — aluminium
a a — width
b b — height
c c — outlet width
d d — outlet height
l l — length
w w — take-off length
g g — take-off width
I3 I3 — take-off length (default I3 = 100 mm)
m m — vertical offset
n n — horizontal offset
e e — take-off offset in length
f f — take-off offset in width
i i — extension (default i = 30 mm)
j j — extension (default j = 30 mm)
The standard versions are made in default dimension sizes which do not have to be specified.
886
ALNOR® ventilation systems
is a registered trademark protected by a technical patent. All modification rights reserved.
Concentric reducing T-pieces
TR9
Description
The concentric reducing T-piece ends are fitted with sheet
angles, and the entire fitting is braced by cross-wise ribbing.
The round take-off connector is male and located symmetrically
in the side wall.
This fitting helps building ductwork with a round take-off at
an angle; the angle value depends on the wall slope at the
take-off side.
type
N N — low-pressure version
S S — medium-pressure version
OCY OCY — galvanized steel
KWS KWS — stainless steel
ALU ALU — aluminium
a a — width
b b — height
c c — outlet height
d d — take-off height
l l — extension (default l = 30 mm)
d1 d1 — take-off diameter
l3 l3 — take-off length (default l3 = 30 mm)
m m — vertical offset
n n — horizontal offset
e e — take-off offset in length
f f — take-off offset in width
i i — extension (default i = 30 mm)
j j — extension (default j = 30 mm)
The standard versions are made in default dimension sizes which do not have to be specified.
887
ALNOR® ventilation systems
is a registered trademark protected by a technical patent. All modification rights reserved.
Four-way pieces with round take-offs
CZ2
Rectangular ducts and fittings
Dimensions
Description
All four-way pieces with round take-offs are fitted with flange
frames made of sheet angles and braced by cross-wise ribbing.
The round take-off ports are coaxial in the standard version.
The standard round take-off ports are male; the CZL2 version is
available on request with male connectors fitted with gaskets.
type
N N — low-pressure version
S S — medium-pressure version
OCY OCY — galvanized steel
KWS KWS — stainless steel
ALU ALU — aluminium
a a — width
b b — height
l l — length
d d — take-off diameter
e e — take-off offset in length
f f — take-off offset in width
I3 I3 — take-off height (default I3 = 100 mm)
d1 d1 — take-off diameter
e1 e1 — take-off offset in length
f1 f1 — take-off offset in width
l4 l4 — take-off height
If all dimensions of both take-off ports are identical, they are aligned according to the default sizing.
888
ALNOR® ventilation systems
is a registered trademark protected by a technical patent. All modification rights reserved.
T-pieces with round take-off
TR2
Description
All T-pieces with round take-offs are fitted with flange frames
made of sheet angles and braced by cross-wise ribbing.
The round take-off port is coaxial in the standard version.
The standard round take-off port is male; the TRL2 version is
available on request with male connector fitted with gaskets.
type
N N — low-pressure version
S S — medium-pressure version
OCY OCY — galvanized steel
KWS KWS — stainless steel
ALU ALU — aluminium
a a — width
b b — height
l l — length
d d — diameter
e e — offset in length
f f — offset in width
l3 l3 — take-off length (default l3 = 100 mm)
The standard versions are made in default dimension sizes which do not have to be specified.
889
ALNOR® ventilation systems
is a registered trademark protected by a technical patent. All modification rights reserved.
Four-way pieces with square take-offs
CZ1
Rectangular ducts and fittings
Dimensions
Description
The four-way piece ends are fitted with sheet angles, and the
entire fitting is braced by cross-wise ribbing.
type
N N — low-pressure version
S S — medium-pressure version
OCY OCY — galvanized steel
KWS KWS — stainless steel
ALU ALU — aluminium
a a — width
b b — height
l l — length
w w — take-off length
d d — take-off width
e e — take-off offset in length
f f — take-off offset in width
I3 I3 — take-off height (default I3 = 100 mm)
w1 w1 — take-off length
d1 d1 — take-off width
e1 e1 — take-off offset in length
f1 f1 — take-off offset in width
I4 I4 — take-off height (default I4 = 100 mm)
If all dimensions of both take-off ports are identical, they are aligned according to the default sizing.
890
ALNOR® ventilation systems
is a registered trademark protected by a technical patent. All modification rights reserved.
Wye tee
TR3
Description
The wye tees are fitted with sheet angles, and the entire fitting
is braced by cross-wise ribbing. This fitting allows building
the ductwork with two take-offs set at any angle.
The width may vary between the two take-off ports.
Vanes can be installed.
type
N N — low-pressure version
S S — medium-pressure version
OCY OCY — galvanized steel
KWS KWS — stainless steel
ALU ALU — aluminium
a a — width
b b — height
c c — take-off 1 height
d d — take-off 2 height
e e — base length
f f — radius (default f = 120 mm)
g g — radius (default g = 120 mm)
β β — angle (default β = 90˚)
α α — angle (default α = 90˚)
j j — extension (default j = 30 mm)
k k — extension (default k = 30 mm)
l l — extension (default l = 30 mm)
m m — extension (default m = 30 mm)
891
ALNOR® ventilation systems
is a registered trademark protected by a technical patent. All modification rights reserved.
Wye tee
TR5
Rectangular ducts and fittings
Dimensions
Description
The wye tee (pant) are fitted with sheet angles, and the entire
fitting is braced by cross-wise ribbing.
The wye te divides the air flow between two parallel legs.
type
N N — low-pressure version
S S — medium-pressure version
OCY OCY — galvanized steel
KWS KWS — stainless steel
ALU ALU — aluminium
a a — height
b b — inlet width
c c — left-hand clear height
d d — right-hand clear height
e e — outlet width
l l — length
g g — take-off spacing
h h — horizontal offset
i i — vertical offset
j j — extension (default j = 30 mm)
k k — extension (default k = 30 mm)
892
ALNOR® ventilation systems
is a registered trademark protected by a technical patent. All modification rights reserved.
T-pieces with take-off bend
TR4
Description
All T-pieces with take-off bends are fitted with flange frames
made of sheet angles and braced by cross-wise ribbing.
A take-off bend provides smooth distribution of air without
increasing the flow turbulence due to the presence of a vane.
type
N N — low-pressure version
S S — medium-pressure version
OCY OCY — galvanized steel
KWS KWS — stainless steel
ALU ALU — aluminium
a a — width
b b — height
c c — clear height
d d — take-off height
l l — length
g g — radius (default g = 120 mm)
α α — angle (default α = 90˚)
j j — extension (default j = 30 mm)
k k — extension (default k = 30 mm)
893
ALNOR® ventilation systems
is a registered trademark protected by a technical patent. All modification rights reserved.
Round duct T-connectors
TR6
Rectangular ducts and fittings
Dimensions
G F
l
A (f )
F
Description
The T-connectors allow building a T-connection between a
round and a square duct. One end features a flange frame
of sheet angles or a hemmed flange. The round duct ends
are provided with hemming for sheet screws in the standard
version.
T-connectors can be fabricated as a fully round T-pieces on
request.
type
N N — low-pressure version
S S — medium-pressure version
OCY OCY — galvanized steel
KWS KWS — stainless steel
ALU ALU — aluminium
a a — duct diameter
l l — round duct length
e e — take-off length
f f — take-off width
g g — take-off height
The standard versions are made in default dimension sizes which do not have to be specified.
894
ALNOR® ventilation systems
is a registered trademark protected by a technical patent. All modification rights reserved.
Rectangular flexible duct connector
QILA
b
a L
Description
Flexible duct connector for rectangular ducts and elements. It is Max. width a: 2500 mm.
made of PQ flange channel and NQ corners interconnected by Max. height b: 2500 mm
AMT flexible connection. Rectangular flexible duct connectors
can be used to join ventilation ducts but above all it is used Standard lengths - L -of the flexible duct connector: 130, 150
to eliminate vibrations caused by air handling units and or 240 mm
fans. The design of the AMT flexible duct connector (a joint (depending on the AMT flexible connetion used for production)
consisting of a layer of fabric and two strips of sheet metal
on both sides)ensures very good airtightness.
Available materials
QILA -…-…-… - galvanized steel sheet, PVC coated fabric
QILA- -HI-T-…-…-… - galvanised steel sheet, silicone coated
Technical Data
fabric
QILA-PU-…-…-… - galvanised steel sheet, polyurethane Temperature
Characteristics
range
(PU) coated fabric
QILA-K-PU-…-…-… - stainless steel polyurethane (PU) coated General use,
PVC -30˚C / +80˚C
QILA-NEP-…-…-… - galvanised steel sheet, neoprene coated economical choic
fabric Resistance to high
temperatures , high
Silicone -30˚C /
resistance to aging,
(HI-T) +260˚C
weather conditions and
chemical substances
Example identification
Polyurethane -30˚C /
Product code: QILA-PU - aaa - bbb - ccc High abrasion resistance
(PU) +180˚C
type Synthetic rubber, suitable
length -30˚C / for outdoor use,
Neoprene
width a +180˚C High resistance to alkalis
height b and petrol.
895
ALNOR® ventilation systems
is a registered trademark protected by a technical patent. All modification rights reserved.
End caps
QES
Rectangular ducts and fittings
Dimensions
Description
The end caps stops square duct ends.
The product is made from galvanized steel sheet.
The flange is made of sheet angles.
type
N
S
C
K
A
a
b
e
N — low-pressure version
S — medium-pressure version
C — galvanized steel
K — stainless steel
A — aluminium
a — width
b — height
e — extension (default e = 30 mm)
896
ALNOR® ventilation systems
is a registered trademark protected by a technical patent. All modification rights reserved.