Professional Documents
Culture Documents
Service Manual: LC-90LE740X
Service Manual: LC-90LE740X
LC-90LE740X
SERVICE MANUAL
No. SY2A4LC90LE74
MODEL LC-90LE740X
In the interests of user-safety (Required by safety regulations in some countries) the set should be restored to its orig-
inal condition and only parts identical to those specified should be used.
CONTENTS
SAFETY PRECAUTION CHAPTER 5. ADJUSTMENT
IMPORTANT SERVICE SAFETY PRE- [1] ADJUSTMENT PROCEDURE ......................5-1
CAUTION ............................................................i [2] PUBLIC MODE SETTING PROCEDURE ......5-14
PRECAUTIONS FOR USING LEAD-FREE [3] USB Clone Specifications............................5-21
SOLDER ............................................................ii
CHAPTER 6. TROUBLESHOOTING TABLE
OUTLINE [1] Failure diagnosis by LED in front of cabinet ........6-1
MAJOR SERVICE PARTS ................................ iii [2] LED flashing specification at the time of an
error (Center icon LED used) ........................6-1
CHAPTER 1. SPECIFICATIONS [3] TROUBLESHOOTING TABLE ......................6-5
[1] SPECIFICATIONS ......................................... 1-1
CHAPTER 7. MAJOR IC INFORMATIONS
CHAPTER 2. OPERATION MANUAL [1] MAJOR IC INFORMATIONS .........................7-1
[1] OPERATION MANUAL .................................. 2-1
CHAPTER 8. OVERALL WIRING/SYSTEM BLOCK
CHAPTER 3. DIMENSIONS DIAGRAM
[1] DIMENSIONS ................................................ 3-1 [1] OVERALL WIRING DIAGRAM ......................8-1
[2] SYSTEM BLOCK DIAGRAM .........................8-2
CHAPTER 4. REMOVING OF MAJOR PARTS
[1] REMOVING OF MAJOR PARTS ................... 4-1 Parts Guide
[2] The location putting on the heat measure
sheet .............................................................. 4-6
[3] Precautions for assembly............................... 4-7
Parts marked with " " are important for maintaining the safety of the set. Be sure to replace these parts with specified ones for maintaining the
safety and performance of the set.
WARNING • Using two clip leads, connect a 1.5k ohm, 10 watt resistor paral-
leled by a 0.15µF capacitor in series with all exposed metal cabinet
1. For continued safety, no modification of any circuit should be parts and a known earth ground, such as electrical conduit or elec-
attempted.
trical ground connected to an earth ground.
2. Disconnect AC power before servicing. • Use an AC voltmeter having with 5000 ohm per volt, or higher, sen-
sitivity or measure the AC voltage drop across the resistor.
C A U T I O N : F O R C O N T I N U E D PROTECTION • Connect the resistor connection to all exposed metal parts having a
AGAINST A RISK OF FIRE REPLACE ONLY WITH return to the chassis (antenna, metal cabinet, screw heads, knobs
and control shafts, escutcheon, etc.) and measure the AC voltage
SAME TYPE FUSE. drop across the resistor.
F7001 (250V 6.3A) All checks must be repeated with the AC cord plug connection
reversed. (If necessary, a nonpolarized adaptor plug must be used
only for the purpose of completing these checks.)
Any reading of 0.75 Vrms (this corresponds to 0.5 mA rms AC.) or
more is excessive and indicates a potential shock hazard which
must be corrected before returning the monitor to the owner.
///////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////
SAFETY NOTICE
Many electrical and mechanical parts in LCD color television have For continued protection, replacement parts must be identical to those
special safety-related characteristics. used in the original circuit.
These characteristics are often not evident from visual inspection, nor The use of a substitute replacement parts which do not have the same
can protection afforded by them be necessarily increased by using safety characteristics as the factory recommended replacement parts
replacement components rated for higher voltage, wattage, etc. shown in this service manual, may create shock, fire or other hazards.
Replacement parts which have these special safety characteristics are
identified in this manual; electrical components having such features
are identified by " " and shaded areas in the Replacement Parts List
and Schematic Diagrams.
///////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////
i
LC-90LE740X
PRECAUTIONS FOR USING LEAD-FREE SOLDER
Indicates lead-free solder of tin, silver and copper. Indicates lead-free solder of tin, silver and copper.
Soldering
• As the melting point of lead-free solder (Sn-Ag-Cu) is about 220 °C which is higher than the conventional lead solder by 40 °C, and as it has poor
solder wettability, you may be apt to keep the soldering bit in contact with the PWB for extended period of time. However, Since the land may be
peeled off or the maximum heat-resistance temperature of parts may be exceeded, remove the bit from the PWB as soon as you confirm the
steady soldering condition.
Lead-free solder contains more tin, and the end of the soldering bit may be easily corroded. Make sure to turn on and off the power of the bit as
required.
If a different type of solder stays on the tip of the soldering bit, it is alloyed with lead-free solder. Clean the bit after every use of it.
When the tip of the soldering bit is blackened during use, file it with steel wool or fine sandpaper.
• Be careful when replacing parts with polarity indication on the PWB silk.
Lead-free wire solder for servicing
PRICE PART
PARTS CODE DESCRIPTION
RANK DELIVERY
ZHNDAi123250E BL J φ0.3mm 250g (1roll)
ZHNDAi126500E BK J φ0.6mm 500g (1roll)
ZHNDAi12801KE BM J φ1.0mm 1kg (1roll)
ii
LC-90LE740X
LC-90LE740X
OUTLINE Service Manual
PWB Unit
OTHER Unit
Service Jigs
iii
LC-90LE740X
CHAPTER 1. SPECIFICATIONS
LC-90LE740X
Service Manual
[1] SPECIFICATIONS
1–1
LC-90LE740X
CHAPTER 2. OPERATION MANUAL
LC-90LE740X
Service Manual
2–1
LC-90LE740X
2–2
LC-90LE740X
2–3
LC-90LE740X
2–4
LC-90LE740X
CHAPTER 3. DIMENSIONS
LC-90LE740X
Service Manual
[1] DIMENSIONS
3–1
LC-90LE740X
CHAPTER 4. REMOVING OF MAJOR PARTS
LC-90LE740X
Service Manual
4 9
1
7 Rear Cabinet (R)
8 Ass'y
12 Rear Cabinet (C)
Stand 2 Ass'y
Unit 5
3 10 11
4–1
LC-90LE740X
2. Removing of Speaker (L/R), Speaker (Woofer) and KEY Unit.
1. Disconnect the SP wire.
2. Remove the 2 lock screws (1) and detach the Speaker (L) (2), Speaker (R) (3).
3. Disconnect the RC wire.
4. Detach the KEY Unit Ass’y (4).
5. Disconnect the KM wire.
6. Remove the 2 lock screws (5) and detach the Key Button (6) from Key Cover (8).
7. Detach the KEY Unit (7) from Key Button (6).
8. Disconnect the SB wire.
9. Detach the Speaker (Woofer) (9).
MAIN Unit
3 Speaker (L) 2
1 Speaker (R) 1
4–2
LC-90LE740X
3. Removing of Connectors, 90” LCD Panel Module Unit Ass’y.
1. Disconnect the following connectors from the MAIN Unit. (LV, PD)
2. Disconnect the following connectors from the POWER/DRIVE Unit. (L1, L2, PD)
3. Disconnect the following connectors from the LCD Control Unit. (PL, LV)
4. Remove the 16 lock screws (1) and detach the 16 Module Fix Angles (2)
5. Remove the 7 Hooks and detach the 90” LCD Panel Module Unit Ass’y (3).
6. Detach the 2 Bottom cover (4).
Hook
Hook
2
[L1] [L2] 2
Module
Fix [PD]
Angle [PL] Module
Fix
1 [LV] Angle
1
MAIN Unit
[PD]
[LV]
4–3
LC-90LE740X
4. Removing of LCD CONTROL Unit, MAIN Unit, POWER/DRIVE Unit.
1. Remove the 5 lock screws (1) and detach the Shield (MAIN) (2).
2. Remove the 3 lock screws (3) and detach the MAIN Unit (4) and Terminal Angle (Bottom) (5).
3. Remove the 6 lock screws (6) and detach the POWER/DRIVE Unit (7).
4. Remove the 4 lock screws (8) and detach the 2 Speaker Holders (9).
5 Terminal
Angle
(Bottom)
7
6 2 Shield
POWER/DRIVE
1 (MAIN)
Unit
4–4
LC-90LE740X
5. Removing of R/C LED Unit, EMBLEM Unit, 3D IR Unit.
1. Detach the R/C LED Unit (1).
2. Disconnect the RA wire.
3. Detach the EMBLEM Unit (2).
4. Disconnect the CI wire.
5. Detach 3D IR Unit (3).
6. Disconnect the IR wire.
4–5
LC-90LE740X
[2] The location putting on the heat measure sheet
1. MAIN PWB Unit
PSPAZC871WJKZ
PSPAZC854WJKZ
4–6
LC-90LE740X
[3] Precautions for assembly
1. Points to be checked and precautions when servicing the unit
Mount the main PWB Ass’y on the backlight chassis and check that the EMI-prevention parts are not peeled and twisted from the access holes. (The
EMI-prevention parts, conductive nonwoven fabric gaskets, must be seen from the access holes.)
[Countermeasure]
Attach the conductive nonwoven fabric gaskets on the shielded case on the main PWB.
687
State where the main PWB and shielded case are assembled
Access hole
Access hole
4–7
LC-90LE740X
The following is a drawing mounting the main PWB Ass’y on the backlight chassis. (The parts indicated by -> are the access holes for confirmation.)
(Main PWB Ass’y => State where the shielded case and RF terminal angle are mounted on the main PWB)
4–8
LC-90LE740X
CHAPTER 5. ADJUSTMENT
LC-90LE740X
Service Manual
The adjustment values are set to the optimum conditions at the factory before shipping. If a value should become improper or an adjustment is
required due to part replacement, make an adjustment according to the following procedure.
1. After replacement of any PWB unit and/or IC for repair, please note the following.
• When replacing the following units, make sure to prepare the new units loaded with updated software.
• When replacing the LCD control PWB, perform the VCOM adjustment.
2.2.2 Preparations
To upgrade the main software, it is necessary to get ready the USB Memory for version upgrade before you start.
Follow the steps below and create the USB Memory for version upgrade.
1. Copy the file LEON_LE740X_xxx.USB for version upgrade to the root directory (folder) of the USB Memory.
NOTE: In the USB Memory drive, do not store other folders or unrelated files, or more than one file for version upgrade.
Now the USB Memory for version upgrade is ready.
5–1
LC-90LE740X
2.2.3 How to upgrade the software
1. Unplug the AC cord.
2. Insert the USB Memory for version upgrade into USB1.
3. Plug in the AC cord with power button pressed down.
4. After 5 seconds, unpress the power button.
5. After the unit startup, the system upgrade screen as shown below within 20-40 seconds.
Software Update
90LE740X
MAIN 50%
SUB MICOM NO DATA
PANEL EEPROM NO DATA
3D IR MICOM
6. Even a single failure in the process will trigger the upgrade failure screen.
Software Update
90LE740X
UPGRADE FAILURE
MAIN Project ID
SUB MICOM NO DATA
PANEL EEPROM NO DATA
3D IR MICOM
NOTE: In the event of a failure, repeat the upgrade process. If the process repeatedly fails, it is likely that the hardware need fixing.
7. Upon completion of the whole process, the upgrade success screen as shown below appears. You can check the new software version on this
screen. The version information appears after the upgrade is complete.
Software Update
90LE740X
UPGRADE SUCCESS
MAIN 100%
SUB MICOM NO DATA
PANEL EEPROM NO DATA
3D IR MICOM
8. Unplug the AC cord and remove the USB Memory for version upgrade.
9. Now the software version upgrade is complete.
NOTE: When you are done with the software version upgrade, start the set, go to the top page of the adjustment process screen and check the main
software version information.
5–2
LC-90LE740X
2.3. Monitor microprocessor software version upgrade
Create the USB memory for monitor microprocessor software version upgrade in the same manner as explained in the “Main software version
upgrade”.
Copy the file LEON_LE740X_xxx.USB and LEONSUBxxx.SMB. (named temporarily) for monitor microprocessor software version upgrade to the
USB memory.
Software Update
90LE740X
MAIN NO DATA
SUB MICOM 50%
PANEL EEPROM NO DATA
3D IR MICOM
6. If the upgrade fails, power led will stop blinking. Also, the upgrade failure screen will be shown if upgrade screen was shown at 5.
Software Update
90LE740X
UPGRADE FAILURE
MAIN NO DATA
SUB MICOM SAME VERSION
PANEL EEPROM NO DATA
3D IR MICOM
NOTE: In the event of a transient failure, upgrade will be automatically retried up to three times. If the process repeatedly fails, hardware may be the
cause.
7. The upgrade success screen will be shown if upgrade screen was shown at 5.
Software Update
90LE740X
UPGRADE SUCCESS
MAIN NO DATA
SUB MICOM 100%
PANEL EEPROM NO DATA
3D IR MICOM
8. Unplug the AC cord and remove the USB Memory for version upgrade.
9. Now the software version upgrade is complete.
NOTE: When you are done with the software version upgrade, start the set, go to the top page of the adjustment process screen and check the mon-
itor microprocessor software version information and panel size information.
5–3
LC-90LE740X
3. Entering and exiting the adjustment process mode
1) Before entering the adjustment process mode, the AV position RESET in the video adjustment menu.
2) While holding down the “VOL(-)” and “INPUT” keys at a time, plug in the AC cord of the main unit to turn on the power.
The letter “<K>” appears on the screen.
3) Next, hold down the “VOL(-)” and “CH( )” keys at a time.
(The “VOL (—)” and “CH ( )” keys should be pressed and held until the display appears.)
Multiple lines of blue characters appearing on the display indicate that the unit is now in the adjustment process mode.
When you fail to enter the adjustment process mode (the display is the same as normal startup), retry the procedure.
4) To exit the adjustment process mode after the adjustment is done, unplug the AC cord from the outlet to make a forced shutdown. (When the
power was turned off with the remote controller, once unplug the AC cord and plug it again. In this case, wait 10 seconds or so before plugging.)
CAUTION: Use due care in handling the information described here lest your users should know how to enter the adjustment process mode. If the
settings are tampered in this mode, unrecoverable system damage may result.
4. Remote controller key operation and description of display in adjustment process mode
1) Key operation
*Input mode is switched automatically when relevant adjustment is started so far as the necessary input signal is available.
2) Description of display
(2) Current selected input
(1) Current page/ (3) Current color system
(5) LCD Panel size/Speaker type
Total pages (4) Inducing display
FRC Version
IR Micom Version
LAMP ERROR 0
3) XXXXX 4) XXXXX
5–4
LC-90LE740X
5. List of adjustment process mode menu
The character string in brackets [ ] will appear as a page title in the adjustment process menu header.
5–5
LC-90LE740X
Page Line Item Description Remarks (adjustment detail, etc.)
5/20
1 HDMI CEC TEST Enter HDMI CEC test
2 HDMI EDID WRITE Enter HDMI EDID WRITING
3 INSPECT USB TERM PORT ALL : - - - - - - Reading inspection of USB memory terminal
4 MONIDATA READ [TEMP/OPC] OFF MONITOR Temperature/OPC Acquisition tool.
5 CAUSE RESET Enter Reset of standby cause
6/20
1 COMP15K ALL ADJ Enter Component 15K picture level adjustment
2 COMP15K MAIN Y GAIN 140 Y GAIN adjustment value
3 COMP15K MAIN CB GAIN 150 Cb GAIN adjustment value
4 COMP15K MAIN CR GAIN 150 Cr GAIN adjustment value
5 COMP15K Y OFFSET 64 Y OFFSET adjustment value
6 COMP15K CB OFFSET 128 CB OFFSET adjustment value
7 COMP15K CR OFFSET 128 CR OFFSET adjustment value
8 COMP15K A_CLAMP 0
7/20
1 HDTV ADJ Enter HDTV video level adjustment
2 HDTV Y GAIN 140 HDTV Y GAIN adjustment value
3 HDTV CB GAIN 150 HDTV Cb GAIN adjustment value
4 HDTV CR GAIN 150 HDTV Cr GAIN adjustment value
5 HDTV Y OFFSET 64 HDTV Y OFFSET adjustment value
6 HDTV CB OFFSET 128 HDTV CB OFFSET adjustment value
7 HDTV CR OFFSET 128 HDTV CR OFFSET adjustment value
8 HDTV A_CLAMP 0
8/20
1 ANALOG PC ADJ Enter DVI ANALOG video level adjustment
2 R OFFSET 64 R CUTOFF adjustment value
3 G OFFSET 64 G CUTOFF adjustment value
4 B OFFSET 64 B CUTOFF adjustment value
5 R GAIN 44 R DRIVE adjustment value
6 G GAIN 44 G DRIVE adjustment value
7 B GAIN 44 B DRIVE adjustment value
8 RGB A_CLAMP 0
9/20
1 VCOM ADJ 64 Common bias adjustment
10/20
1 DDR2 CHECK Enter Execute DDR check
2 BA[1:0] 0x00
3 ADDR[13:0] 0x0000
4 DQ[15:0] 0x0000
5 FRC ON/OFF Enter Execute FRC ON/OFF
11/20
1 R GAIN (LO) 0 R DRIVE adjustment value
2 G GAIN (LO) 0 G DRIVE adjustment value
3 B GAIN (LO) 0 B DRIVE adjustment value
4 R GAIN (HI) 0 R DRIVE adjustment value
5 G GAIN (HI) 0 G DRIVE adjustment value
6 B GAIN (HI) 0 B DRIVE adjustment value
12/20
1 MONITOR TIME OUT ON Monitor and the main communication time-out setting
2 MONITOR MAX TEMP 59 MONITOR MAX temperature setting
3 MONITOR EEP READ/WRITE WRITE MONITOR EEPROM READ/WRITE Setting/execution
4 MONITOR EEP ADR 0x 0 MONITOR EEPROM arbitrary addressing
5 MONITOR EEP DATA 0x 0 MONITOR EEPROM arbitrary data specification
13/20
1 LCD TEST PATTERN
2 LCD TEST PATTERN 1 NOT SUPPORT Pattern with built-in LCD controler display
3 LCD TEST PATTERN 2 OFF
4 LCD TEST PATTERN 3 NOT SUPPORT
5 LCD TEST PATTERN 4 NOT SUPPORT
5–6
LC-90LE740X
Page Line Item Description Remarks (adjustment detail, etc.)
14/20
1 T-CON VERSION EXT.1
2 T-CON VERSION EXT.2
3 T-CON VERSION EXT.3
4 T-CON VERSION EXT.4
15/20
1 3D HDMI FPGA Version
2 2D→3D FPGA Version
3 3D LED BRIGHTNESS 90
4 3D IR EMITTER CONTROL ON
16/20
1 CROSS TALK ADJ MODE OFF
2 CROSS TALK TH1
3 CROSS TALK TH2
4 CROSS TALK TH3
5 CROSS TALK TH4
6 CROSS TALK GAIN1
7 CROSS TALK GAIN2
8 CROSS TALK GAIN3
17/20
1 WIFI SSID 2.4GHz AF00
2 WIFI SSID 5GHz AF50
3 WIFI RSSI 2.4GHz -50
4 WIFI RSSI 5GHz -50
5 WIFI TIME 2.4GHz 10
6 WIFI TIME 5GHz 10
7 WIFI RSSI TEST 2.4GHz and 5GHz
RSSI(Passive)
8 WIFI RSSI RESULT 2.4GHz ERR - 1,
5GHz ERR - 1
18/20
1 READ/WRITE READ Read/Write
2 SLAVE/ADDRESS SLAVE0 Slave address
3 REGISTER ADDRESS 0x 0 Register address
0x 0
4 WRITE DATA 0x 0 Writing data
0x 0
5 READ DATA 0x 0 Reading data
0x 0
19/20
1 ERROR STANDBY CAUSE 1 NO RECORD ERROR STANDBY CAUSE
2 ERROR STANDBY CAUSE 2 NO RECORD
3 ERROR STANDBY CAUSE 3 NO RECORD
4 ERROR STANDBY CAUSE 4 NO RECORD
5 ERROR STANDBY CAUSE 5 NO RECORD
6 STANDBY CAUSE RESET OFF Reset stand by cause.
20/20
1 EEP SAVE OFF Writing setting values to EEPROM.
2 EEP RECOVER OFF Reading setting values from EEPROM.
3 MONITOR ERROR CAUSE RESET OFF Reset of monitor error cause
4 MODEL NAME LE840X MODEL NAME
5 PANEL SIZE 60 Panel size setting.
6 VER UP FLAG ENABLE Enter
7 PANEL LIMIT ON
8 PANEL RANGE LIMIT 230
9 SHORT CHECK MODE Enter Check LED Back Light
10 SHORT CHECK CURRENT 60
11 PRODUCT EEP ADR 0x 0 Don't touch when serving (for producer of factory)
12 PRODUCT EEP DATA 0x 0 Don't touch when serving (for producer of factory)
13 PRODUCT FACTORY 0x 0 Don't touch when serving (for producer of factory)
14 TEST NETWORK UPDATE NO Don't touch when serving (for producer of factory)
5–7
LC-90LE740X
6. Special features
* STANDBY CAUSE (Page 1/20)
Display of a cause (code) of the last standby
The cause of the last standby is recorded in EEPROM whenever possible.
Checking this code will be useful in finding a problem when you repair the troubled set.
* EEP SAVE (Page 20/20)
Storage of EEP adjustment value
* EEP RECOVER (Page 20/20)
Retrieval of EEP adjustment value from storage area
5–8
LC-90LE740X
Display Error Reason
11 Communication Error H Regular communication Time-out
16 LCD Module Error Lamp Error
1A Other Error 2 Monitor Temperature Error
1D Power supply Error1 PS_ON(AC_DET) Error
1E Power supply Error 2 D_POW(DET_13V) Error
1F Power supply Error 3 D_POW(DET_D3V3) Error
21 Power supply Error 5 Panel Power Error
23 Other Error 3 Error Standby request from Main CPU
1/2 1/2
1/2
1/2
5–9
LC-90LE740X
10. Video signal adjustment procedure
The adjustment process mode menu is listed in Section 5.
Signal generator level adjustment check (Adjustment to the specified level)
• Composite signal PAL/SECAM : 0.7Vp-p ± 0.02Vp-p (Pedestal to white level)
• RGB signal : 0.7Vp-p ± 0.02Vp-p
• 15K component signal (50 Hz) : Y level : 0.7Vp-p ± 0.02Vp-p (Pedestal to white level)
: PB, PR level : 0.7Vp-p ± 0.02Vp-p
• 33K component signal (50 Hz) : Y level : 0.7Vp-p ± 0.02Vp-p (Pedestal to white level)
: PB, PR level : 0.7Vp-p ± 0.02Vp-p
• Composite signal NTSC : 0.714Vp-p ± 0.02Vp-p (Pedestal to white level)
[Terminal]
INPUT6 video input
100% white Black
2 Auto adjustment Adjustment process Bring the cursor on [PAL ADJ] and press [ENTER].
performance [PAL ADJ] [PAL ADJ OK] appears when finished.
page 4/20
* ATTENTION: Please execute [3. TUNER adjustment] afterwards if you adjust [2. PAL signal adjustment] after all adjustments are completed.
100% white
2 Auto adjustment Adjustment process Bring the cursor on [TUNER ADJ] and press [ENTER].
performance [TUNER ADJ] [TUNER ADJ OK] appears when finished.
page 3/20
5 – 10
LC-90LE740X
10.4. NTSC signal adjustment
[Terminal]
INPUT6 video input
2 Auto adjustment Adjustment process Bring the cursor on [N358 ADJ] and press [ENTER].
performance [N358 ADJ] [N358 ADJ OK] appears when finished.
page 4/20
[Terminal]
INPUT6 video input
2 Auto adjustment Adjustment process Bring the cursor on [SECAM ADJ] and press [ENTER].
performance [SECAM ADJ] [SECAM ADJ OK] appears when finished.
page 4/20
[Terminal]
INPUT5 COMPONENT IN
100% white Black
2 Auto adjustment Adjustment process Bring the cursor on [COMP15k ALL ADJ] and press [ENTER] [COMP15k ALL
performance [COMP15k ALL ADJ] ADJ] [OK] appears when finished.
page 6/20
5 – 11
LC-90LE740X
10.7. ADC adjustment (Component 33K)
[Terminal]
INPUT5 COMPONENT IN
100% white Black
2 Auto adjustment Adjustment process Bring the cursor on [HDTV ADJ] and press [ENTER].
performance [HDTV ADJ] [HDTV ADJ OK] appears when finished.
page 7/20
[Terminal]
INPUT7 PC IN
100% white Black
2 Auto adjustment Adjustment process Bring the cursor on [ANALOG PC ADJ] and press [ENTER].
performance [ANALOG PC ADJ] menu [ANALOG PC ADJ OK] appears when finished.
page 8/20
[Condition of the unit for inspection] : Modulated light (+16), Colour temperature (High)
AV MODE: DYNAMIC
Active Backlight: OFF
OPC: OFF
Asing Time: Min, 60 minute
[Input signal condition] : HDMI 1080i 15IRE (LO), 78IRE (HI)
[Adjustment reference device] : Minolta CA-210
[Adjustment procedure]
1) Display the current adjustment status at R/G/B_GAIN (HI). (Page 11/20 of process adjustment)
The signal of 78IRE is input.
2) Read the value of the luminance meter. x = 0.272, y = 0.277
3) Change R_GAIN (HI)/B_GAIN (HI) (Adjustment offset value) on page 11/20 of process adjustment so that the values of the luminance meter
approach x = 0.272 and y = 0.277.
(Basically, G is not changed. If adjustment fails with R and B, change G. When G is lowered, the weaker of R or B must be fixed.)
4) Display the adjustment status of the current R/G/B_GAIN (LO).
The signal of 15IRE is input.
Change R_GAIN (LO)/B_GAIN (LO) (adjustment offset value) on page 11/20 of process adjustment so that the values of the luminance meter
approach x = 0.272 and y = 0.277.
5) Both HI and LO are repeating the step from 1 to 4 until becoming an aim value.
[Adjustment reference standard value]
Adjustment spec ± 0.002 Inspection spec ± 0.004 (point LO)
Adjustment spec ± 0.001 Inspection spec ± 0.002 (point HI)
6) After completing adjustments, set EEP SAVE (20/20) to ON in the process menu to save the white balance adjustment value.
5 – 12
LC-90LE740X
12. Key writing
12.1. EDID writing (Main PWB: QPWBXF953WJ**)
The version confirmation screen appears on the green screen. It is completed when [SUC-
CESS] is displayed at the top.
(If error occurs, [ERROR] is displayed on the red screen.)
•Turn off the AC power.
The following items are initialized when configuring the factory setting.
1) User set value
2) Channel data (broadcasting frequency, etc.)
3) Password setting value
4) Operating time
5) StandbyCause
6) Auto installation flag
7) V-CHIP block setting value
5 – 13
LC-90LE740X
[2] PUBLIC MODE SETTING PROCEDURE
1. How to start Public Mode
Starting the Public Mode
• There is one following ways to display the PUBLIC Mode setting screen.
Operation procedure
• The initial input position is the digit at the left end.
• For the numeric keys “0” to “9” of R/C, key input is accepted.
Input of the other keys is prohibited.
• Change “—” to “ * ” by inputting the numeric key at the input position, and shift the input position rightward one digit.
• When three digits are completely input, the Pass Word is judged.
c) Check the Pass Word by inputting three digits.
If the Pass Word “0” “2” “7”, it shifts to the PUBLIC Mode setting screen.
In another case, the screen is erased, and it operates in the ordinary mode.
2) In the adjustment process mode, turn on “PUBLIC MODE”. Also press the “CH ( )” or “CH ( )” and “VOL(+)” keys on the set at once and turn
on the power.
5 – 14
LC-90LE740X
4. Public Mode Menu
The guidance is not displayed on screen.
Setup procedure
• To move the cursor up and down, use the “cursor UP/DOWN” key (remote controller) and “CH ( )/( )” key (remote controller and set).
• To change the settings, use the “cursor RIGHT/LEFT” key (remote controller) and “VOL (+)/(–)” key (remote controller and set).
• To save new settings, keep the cursor at “EXECUTE” and use “ENTER” key (remote controller and set).
27$.+%/1&'
219'410(+:'&=8#4+#$.'?
5*76&190/1&'=014/#.?
/#:+/7/81.7/'=?
81.7/'(+:'&=8#4+#$.'?
81.7/'(+:'&.'8'.=?
4%$76610=4'5210&?
2#0'.$76610=4'5210&?
/'07$76610=4'5210&?
#8215+6+10(+:'&=8#4+#$.'?
105%4''0&+52.#;=;'5?
+0276/1&'56#46=014/#.?
+0276/1&'(+:'&=8#4+#$.'?
.17&52'#-'4=10?
4%2#6*6*417)*=1((?
%21910=&+5#$.'?
27$.+%/1&'=1((?
4'5'6
':'%76'
5 – 15
LC-90LE740X
5. On Setting Items
1) Power ON fixed [POWER ON FIXED]
If the power button is pressed in the ordinary mode in setting to “FIXED_ALL” and “FIXED_BODYKEY”, the caution is displayed for 5 seconds.
When power button on the main unit is pressed When power button on R/C is pressed
2) Instantaneous current shutdown setting in turning off the power [SHUT DOWN MODE]
5 – 16
LC-90LE740X
4) Volume fixed [VOLUME FIXED]
5 – 17
LC-90LE740X
8) Menu operation [MENU BUTTON]
5 – 18
LC-90LE740X
11) Start mode [INPUT MODE START]
Option “NORMAL” or “Input source 1 (input selection or channel)” ... (loop enabled)
Default “NORMAL”
Function Which kinds of input source or channel is decided when the power turning on.
NORMAL : The content of the last memory is followed.
Remarks • When setting to not Normal, ON TIMER (Watching reservation) has priority.
• When setting to “NORMAL”, [INPUT MODE FIXED] is set to “VARIABLE” and [INPUT MODE FIXED] is prohibited to
select. (selection impossible.)
Example of option: “NORMAL”, “TVD (002TV)”, “INPUT1”, “INPUT2”, “INPUT3”, “HDMI1”, “HDMI2”, “HDMI3”, “HDMI4”.
5 – 19
LC-90LE740X
15) 232C power ON control [232C POWON]
5 – 20
LC-90LE740X
[3] USB Clone Specifications
Input “369” as password on the copy mode screen using the same input method as Public Mode on the previous page.
<FIG 1>
* Do not focus on button before recognition
of USB device and use is possible. <FIG 2>
Wait display blinks for 1 second
Copy mode Copy mode during implementation. Change
Press [ENTER] button to Select color during this
TV USB [ Start ] TV USB [ Wait… ] time to disable key reception.
USB TV [ Start
St ] USB TV [ Start ] USB TV [ Start ]
<FIG 1>
* Do not focus on button before recognition
of USB device and use is possible. <FIG 2>
Wait display blinks for 1 second
Copy mode Copy mode during implementation. Change
Press [ENTER] button to Select color during this
TV USB [ St
Start ] TV USB [ Start ] time to disable key reception.
5 – 21
LC-90LE740X
3. USB Clone Restrictions
• Be sure to set the network setting (Setup/View setting/Network setup) after writing the data by USB Clone (USB→TV).
• Use USB memory with a memory capacity of 1M byte or greater.
• The USB memory file system is FAT (FAT32).
• No connection of multiple USB memories to the USB port.
• If the USB memory connection is one connection, carry out clone operations regardless of what USB port it is connected to.
• Up until recognition of the USB device and usage enable, do not focus on the button shown in FIG 1 of the “1. Screen Specifications (copy mode
<TV→USB>)” and “2. Screen Specifications (copy mode <USB→TV>)” (maximum 45 seconds).
• The following must agree during sucking from TV (TV→USB) and writing to TV (USB→TV).
⋅ Vender name (fixed)
⋅ Key information (fixed)
⋅ USB Clone Ver.
⋅ Inch size
⋅ Shipping destination settings
⋅ Model name
⋅ Software version
5 – 22
LC-90LE740X
CHAPTER 6. TROUBLESHOOTING TABLE
LC-90LE740X
Service Manual
START
Yes
Is the Center Icon flashing? Check "[2] LED flashing specification at the time of an error (Center icon LED used)".
No
Yes
No
Is the Backlight lighting? Check "LED Backlight does not turn on.".
Yes
Check "Picture does not display.".
[2] LED flashing specification at the time of an error (Center icon LED used)
1. Display method
• Since only the center icon LED can be used, slow flashing and fast flashing are combined.
• After recovering from an error, if the same error cannot be generated again, refer to MONITOR ERR CAUSE on the adjustment process mode.
Center icon ON
OFF
1600ms 1600ms
400ms
400ms 300ms
100ms
6–1
LC-90LE740X
Table 1. Concrete flashing pattern
Detail display
Item Cause
Slow flashing Fast flashing
Inverter/Lamp system failure Flashes once Flashes once Lamp error
Power PWB Flashes twice Flash once Power supply error 2 (*2) AC_DET error
failure Flash twice Power supply error 2 (*2) UR+13V error
(Power failure, etc.) Flash 3 times Power supply error 2 (*2) D+3.3V error
Flash 5 times Panel power supply error
Main PWB Flashes 3 times Flashes once Initial communication error
failure Flashes twice Start-up confirmation communication error
(Communication Flashes 3 times Regular communication error
failure, etc.) Flashes 5 times Other communication error
Others Flashes 4 times Flashes once Temperature error
Flashes 3 times Notification from the main microprocessor (*3)
*2: They depend on the system. Power supply error is defined from product to product.
*3: For details, refer to ERROR STANDBY CAUSE on the adjustment process mode.
6–2
LC-90LE740X
3. New method
LED flashing timing chart at the time of an error
1) Inverter/Lamp failure details (Flashes slowly once and flashes fast) Note
2) Power failure details (Flashes slowly twice and flashes fast) Note
3) Communication failure details (Flashes slowly 3 times and flashes fast) Note
6–3
LC-90LE740X
4) Other failure details (Flashes slowly 4 times and flashes fast) Note
6–4
LC-90LE740X
[3] TROUBLESHOOTING TABLE
• LED Backlight does not turn on.
Do you start?
YES
When main unit is replaced, does it start normally?
YES NO
Replace main unit. When LCD control unit is replaced, does it start normally?
YES
Replace LCD control unit.
NO
When the parts in the panel can be replaced. →Replace all LED-bars in the panel module.
When the parts in the panel cannot be replaced. →Replace panel module.
Do you start?
NO
When power supply unit is replaced, does it start normally?
YES
Replace power supply unit.
NO
When main unit is replaced, does it start normally?
YES
Replace main unit.
NO
When LCD control unit is replaced, does it start normally?
YES
Replace LCD control unit.
NO
When the parts in the panel can be replaced. →Replace all LED-bars in the panel module.
When the parts in the panel cannot be replaced. →Replace panel module.
6–5
LC-90LE740X
YES
Replace C-S FPC.
NO
When C-PWB is replaced, does screen display normally?
YES
Replace C-PWB.
(Adjust “VCOM ADJ” after replace C-PWB)
NO
Replace Panel HIRAKI.
(Adjust “VCOM ADJ” after replace Panel HIRAKI)
6–6
LC-90LE740X
NO
Please enter the adjustment process mode and display "LCD TEST It isn't the fault of a C-PWB.
PATTERN 2" of 13 page. YES Please check operation with reference to other items.
Please press volume (-)/(+) keys and a test pattern is displayed.
Is it all usually displayed?
NO
Is only the half of the right screen or the left screen displayed normally? • It is checked whether FFC (to Panel) is connected correctly.
YES • Replace another C-PWB.
NO
Please check the C-PWB.
Replace another board.
6–7
LC-90LE740X
Is INPUT-1 selected on the input select menu screen? NO Select INPUT-1 on the input select menu screen
for the right input signal.
YES
Does the HOT PLUG detection function? NO Check the line between the pin(18) of SC1501 and
Does the DDC5V signal come from pin (18) of SC1501 to pin (60) of IC2601 the pin(60) of IC2601.
(HDMI_SW)?
YES
Does the HPD signal come from pin (59) of IC2601 to pin (19) of SC1501? NO Check the line between the pin (19) of SC1501
and the pin (59) of IC2601.
YES
Is IC2601(HDMI-SW) accessed by I2C, with HDMI connected, to read the DDC-I2C Check the DDC-I2C line and its peripheral circuits.
NO
SCL/SDA data? SC1501 pin(15)(SCL), pin(16)(SDA)
IC2601 pin(58), pin(57)
YES
Are there the TMDS signal at input pins of IC3301(CPU)? Check the TMDS line (between SC1501 and
NO IC2601) and its peripheral circuits.
[IC2601 TMDS input pins]
pin(26/27)(CLK-/+), pin(28/29)(D0-/+), pin(30/
31)(D1-/+), pin(31/33)(D2-/+).
Check the TMDS line (between IC2601 and
IC3301) and its peripheral circuits.
[IC3301 TMDS input pins]
pin(AH35/AH34)(CLK-/+),
pin(AG35/AG34)(D0-/+),
pin(AG37/AG36)(D1-/+),
pin(AF35/AF34)(D2-/+).
Check the I2C line (between IC2601 and IC3301).
IC2601:pin(71)(SCL), pin(70)(SDA)
IC3301:pin(AN12), pin(AP12)
Check IC2601 and its peripheral circuits.
YES
Is the T-CON PWB connected? NO Check the T-CON PWB and harness.
VBO_LOCKN pin (40) of SC3801 become Low if there is no problem in the connec- Check IC3301 and SC3801 and their peripheral
tion. circuits in Main PWB.
YES
Are the V-By-One HS signal input to the pin of SC3801? NO Check IC3301 and its peripheral circuits.
VBO_CN_TXA+/- (36/37pin), VBO_CN_TXB+/- (32/33pin), (IC3501/IC3502/IC3503/IC3504, etc.)
VBO_CN_TXC+/- (28/29pin), VBO_CN_TXD+/- (24/25pin).
YES
Check the panel module and harness.
6–8
LC-90LE740X
Is INPUT-2 selected on the input select menu screen? NO Select INPUT-2 on the input select menu screen
for the right input signal.
YES
Does the HOT PLUG detection function? NO Check the line between the pin(18) of SC1502
Does the DDC5V signal come from pin (18) of SC1502 to pin (75) of IC2601 and the pin(75) of IC2601.
(HDMI_SW)?
YES
Does the HPD signal come from pin (74) of IC2601 to pin (19) of SC1502? NO Check the line between the pin (74) of IC2601
and the pin (19) of SC1502.
YES
Is IC2601(HDMI-SW) accessed by I2C, with HDMI connected, to read the DDC-I2C Check the DDC-I2C line and its peripheral cir-
SCL/SDA data? NO cuits.
SC1501 pin(15)(SCL), pin(16)(SDA)
IC2601 pin(73), pin(72)
YES
Are there the TMDS signals at input pin of IC3301(CPU)? Check the TMDS line (between SC1502 and
NO IC2601) and its peripheral circuits.
[IC2601 TMDS input pins]
pin(17/18)(CLK-/+), pin(19/20)(D0-/+), pin(21/
22)(D1-/+), pin(23/24)(D2-/+).
Check the TMDS line (between IC2601 and
IC3301) and its peripheral circuits.
[IC3301 TMDS input pins]
pin(AH35/AH34)(CLK-/+),
pin(AG35/AG34)(D0-/+),
pin(AG37/AG36)(D1-/+),
pin(AF35/AF34)(D2-/+).
Check the I2C line (between IC2601 and
IC3301).
IC2601:pin(71)(SCL), pin(70)(SDA)
IC3301:pin(AN12), pin(AP12)
Check IC2601 and its peripheral circuits.
YES
Is the T-CON PWB connected? NO Check the T-CON PWB and harness.
VBO_LOCKN (40pin) of SC3801 become Low if there is no problem in the connec- Check IC3301 and SC3801 and their peripheral
tion. circuits in Main PWB.
YES
Are the V-By-One HS signal input to the pin of SC3801? NO Check IC3301 and its peripheral circuits.
VBO_CN_TXA+/- (36/37pin), VBO_CN_TXB+/- (32/33pin), (IC3501/IC3502/IC3503/IC3504, etc.)
VBO_CN_TXC+/- (28/29pin), VBO_CN_TXD+/- (24/25pin).
YES
Check the panel module and harness.
6–9
LC-90LE740X
Is INPUT-3 selected on the input select menu screen? NO Select INPUT-3 on the input select menu screen for
the right input signal.
YES
Does the HOT PLUG detection function? NO Check the line between the pin(18) of SC1503 and
Does the DDC5V signal come from pin (18) of SC1503 to pin (56) of IC2601 the pin(56) of IC2601.
(HDMI_SW)?
YES
Does the HPD signal come from pin (55) of IC2601 to pin (19) of SC1503? NO Check the line between the pin (55) of IC2601 and
the pin (19) of SC1503.
YES
Is IC2601(HDMI-SW) accessed by I2C, with HDMI connected, to read the DDC-I2C Check the DDC-I2C line and its peripheral circuits.
NO
SCL/SDA data? SC1501 pin(15)(SCL), pin(16)(SDA)
IC2601 pin(54), pin(53)
YES
Are there the TMDS signal at input pins of IC3301(CPU)? Check the TMDS line (between SC1503 and
NO IC2601) and its peripheral circuits.
[IC2601 TMDS input pins]
pin(8/9)(CLK-/+), pin(10/11)(D0-/+), pin(12/13)(D1-/
+), pin(14/15)(D2-/+).
Check the TMDS line (between IC2601 and IC3301)
and its peripheral circuits.
[IC3301 TMDS input pins]
pin(AH35/AH34)(CLK-/+), pin(AG35/AG34)(D0-/+),
pin(AG37/AG36)(D1-/+), pin(AF35/AF34)(D2-/+).
Check the I2C line (between IC2601 and IC3301).
IC2601:pin(71)(SCL), pin(70)(SDA)
IC3301:pin(AN12), pin(AP12)
Check IC2601 and its peripheral circuits.
YES
Is the T-CON PWB connected? NO Check the T-CON PWB and harness.
VBO_LOCKN pin(40) of SC3801 become Low if there is no problem in the connec- Check IC3301 and SC3801 and their peripheral cir-
tion. cuits in Main PWB.
YES
Are the V-By-One HS signal input to the pin of SC3801? NO Check IC3301 and its peripheral circuits.
VBO_CN_TXA+/- (36/37pin), VBO_CN_TXB+/- (32/33pin), (IC3501/IC3502/IC3503/IC3504, etc.)
VBO_CN_TXC+/- (28/29pin), VBO_CN_TXD+/- (24/25pin).
YES
Check the panel module and harness.
6 – 10
LC-90LE740X
Is INPUT-4 selected on the input select menu screen? NO Select INPUT-4 on the input select menu screen for
the right input signal.
YES
Does the HOT PLUG detection function? NO Check the line between the pin(18) of SC1504 and the
Does the DDC5V signal come from pin (18) of SC1504 to pin (51) of IC2601 pin(51) of IC2601.
(HDMI_SW)?
YES
Does the HPD signal come from pin (50) of IC2601 to pin (19) of SC1504? NO Check the line between the pin (50) of IC2601 and the
pin (19) of SC1504.
YES
Is IC2601(HDMI-SW) accessed by I2C, with HDMI connected, to read the DDC- Check the DDC-I2C line and its peripheral circuits.
NO
I2C SCL/SDA data? SC1501 pin(15)(SCL), pin(16)(SDA)
IC2601 pin(49), pin(48)
YES
Are there the TMDS signal at input pins of IC3301(CPU)? Check the TMDS line (between SC1504 and IC2601)
NO and its peripheral circuits.
[IC2601 TMDS input pins]
pin(99/100)(CLK-/+), pin(1/2)(D0-/+), pin(3/4)(D1-/+),
pin(5/6)(D2-/+).
Check the TMDS line (between IC2601 and IC3301)
and its peripheral circuits.
[IC3301 TMDS input pins]
pin(AH35/AH34)(CLK-/+), pin(AG35/AG34)(D0-/+),
pin(AG37/AG36)(D1-/+), pin(AF35/AF34)(D2-/+).
Check the I2C line (between IC2601 and IC3301).
IC2601:pin(71)(SCL), pin(70)(SDA)
IC3301:pin(AN12), pin(AP12)
Check IC2601 and its peripheral circuits.
YES
Is the T-CON PWB connected? NO Check the T-CON PWB and harness.
VBO_LOCKN (40pin) of SC3801 become Low if there is no problem in the con- Check IC3301 and SC3801 and their peripheral cir-
nection. cuits in Main PWB.
YES
Are the V-By-One signal input to the pin of SC3801? NO Check IC3303 and its peripheral circuits.
VBO_CN_TXA+/- (36/37pin), VBO_CN_TXB+/- (32/33pin), (IC3501/IC3502/IC3503/IC3504, etc.)
VBO_CN_TXC+/- (28/29pin), VBO_CN_TXD+/- (24/25pin).
YES
Check the panel module and harness.
6 – 11
LC-90LE740X
No video (2)
NO
Select INPUT-5 on the input select menu screen for the right
input signal.
Is "COMPONENT" selected on the input select menu screen? Select "COMPONENT" on the input menu screen for the
right input signal.
NO
YES YES
Are there the COMPONENT video signal inputs at pins(AU26/AP25)(Y)/(AR26)(Pb) and (AP26)(Pr) of IC3301(CPU)?
NO
Check the line between the input terminals of J513 and IC3301.
J513 pin(1)(Y) pin(2)(Pb) pin(3)(Pr)
IC3301 pin(AU26/AP25) pin(AR26) pin(AP26)
YES
Is the T-CON PWB connected? NO Check the T-CON PWB and harness.
VBO_HTPDN pin (40) of SC3801 become Low if there is no problem in the connection. Check IC3301 and SC3801 and their periph-
eral circuits in Main PWB.
YES
Are the V-By-One HS signal input to the pin of SC3801? NO Check IC3301 and its peripheral circuits.
VBO_CN_TXA+/- (36/37pin), VBO_CN_TXB+/- (32/33pin), (IC3501/IC3502/IC3503/IC3504, etc.)
VBO_CN_TXC+/- (28/29pin), VBO_CN_TXD+/- (24/25pin).
YES
Check the panel module and harness.
6 – 12
LC-90LE740X
No video (3)
COMPSITE: No external input video [INPUT-5] COMPSITE: No external input video [INPUT-6]
Is INPUT-5 selected on the input select menu screen? Is INPUT-6 selected on the input select menu screen?
NO NO
Select INPUT-5 on the input select menu screen for Select INPUT-6 on the input select menu
the right input signal. screen for the right input signal.
NO
Is "VIDEO" selected on the input select menu
screen?
YES
Select "VIDEO" on the input menu
screen for the right input signal.
YES NO YES
Is there the COMPOSITE signal input at pin (AT30) of IC3301 Is there the COMPOSITE signal input at pin (AR31) of IC3301
(CPU)? (CPU)?
NO NO
Check the line between pin (2) of J509 Check the line between pin (2) of J514 and
and pin (AT30) of IC3301 (CPU). pin (AR31) of 3301 (CPU)?
J509:pin(2) J514:pin(2)
IC3301:pin(AT30) IC3301:pin(AR31)
YES YES
Is the T-CON PWB connected? NO Check the T-CON PWB and harness.
VBO_LOCKN pin(40) of SC3801 become Low if there is no problem in the connection. Check IC3301 and SC3801 and their
peripheral circuits in Main PWB.
YES
Are the V-By-One HS signal input to the pin of SC3801? NO Check IC3301 and its peripheral circuits.
VBO_CN_TXA+/- (36/37pin), VBO_CN_TXB+/- (32/33pin), (IC3501/IC3502/IC3503/IC3504, etc.)
VBO_CN_TXC+/- (28/29pin), VBO_CN_TXD+/- (24/25pin).
YES
Check the panel module and harness.
6 – 13
LC-90LE740X
No video (4)
NO
Select INPUT-7 on the input select menu screen for the right input signal.
Is IC2601 (HDMI-SW) accessed by I2C, with PC connected, to read the VGA_SCL/SDA data?
Check the DDC-12C line and its peripheral circuits. (IC2601 and its peripherals).
YES
Are there the video signal inputs at pins (AR24/AT24) (G), (AU24) (B) and (AR25) (R) of IC3301 (CPU)?
Are there the VSYNC/HSYNC signal inputs at pins (AM25) and (AN25) of IC3301?
NO
Check the line between SC504 and IC3301, and their peripheral circuits.
YES
Is the T-CON PWB connected? NO Check the T-CON PWB and harness.
VBO_LOCKN pin (40) of SC3801 become Low if there is no problem in the connection. Check IC3301 and SC3801 and their
peripheral circuits in Main PWB.
YES
Are the V-By-One HS signal input to the pin of SC3801? NO Check IC3301 and its peripheral circuits.
VBO_CN_TXA+/- (36/37pin), VBO_CN_TXB+/- (32/33pin), (IC3501/IC3502/IC3503/IC3504, etc.)
VBO_CN_TXC+/- (28/29pin), VBO_CN_TXD+/- (24/25pin).
YES
Check the panel module and harness.
6 – 14
LC-90LE740X
No video (5)
No video at UHF/VHF broadcast signal reception No video at digital broadcast signal reception
Are there the IF signal at input pins(AT32/AU32)(TUN_IFN/P) Are there the IF signal at input pins(AT32/AU32)(TUN_IFN/P) of
of IC3301(CPU)? IC3301(CPU)?
Is there IF-AGC signal at input pin(12) of TU1104?
NO NO
Check the IF signal line between IC3301 and Check the IF signal line between IC3301 and
TU1104, and their peripheral circuits. TU1104, and their peripheral circuits.
Check the Tuner I2C lines. Check the IF-AGC line between pin(U35) of IC3301
TU1104:pin(5)(TU_SCLK, pin(4)(TU_SDATA) and pin(12) of TU1104.
IC3301:pin(V35), pin(V34)
Check the Tuner I2C lines.
TU1104:pin(5)(TU_SCLK, pin(4)(TU_SDATA)
YES YES IC3301:pin(V35), pin(V34)
Is the T-CON PWB connected? NO Check the T-CON PWB and harness.
VBO_LOCKN (40pin) of SC3801 become Low if there is no problem in the connec- Check IC3301 and SC3801 and their peripheral cir-
tion. cuits in Main PWB.
YES
Are the V-By-One HS signal input to the pin of SC3801? NO Check IC3301 and its peripheral circuits.
VBO_CN_TXA+/- (36/37pin), VBO_CN_TXB+/- (32/33pin), (IC3501/IC3502/IC3503/IC3504, etc.)
VBO_CN_TXC+/- (28/29pin), VBO_CN_TXD+/- (24/25pin).
YES
Check the panel module and harness.
6 – 15
LC-90LE740X
No video (6)
MHL:No external input video [INPUT-4] (using MHL Cable with Mobile Phone)
Is INPUT-4 selected on the input select menu screen? Select INPUT-4 on the input select menu screen for the right
NO input signal.
YES
Does the MHL Cable detection function? Check the MHL Cable.
Does the CD_SENSE signal (High level) come from pin(2) of SC1504 to NO Check the line between the pin(2) of SC1504 and the pin(69) of
pin(69) of IC2601(HDMI-SW)? IC2601.
YES
Does the CBUS signal come from pin(50) of IC2601 to pin(19) of Check the CBUS line between the pin(19) of SC1504 and the
SC1504? NO pin(50) of IC2601, and their peripheral circuits.(Q1507, etc.)
YES
Does the VBUS signal (5V valtage power signal) output from pin(6) of Check the VBUS line between the pin(19) of SC1504 and the
IC1507 to pin(18) of SC1504? NO pin(6) of IC1507, and their peripheral circuits.(IC1508, IC1509,
etc)
YES
Are there the TMDS signal at input pin(1/2)(D0-/+) of IC2601(HDMI- Check the TMDS line (between SC1504 and IC2601) and its
SW)? NO peripheral circuits.(IC1504, etc.)
YES
Are there the TMDS signal at input pins of IC3301(CPU)? Check the TMDS line (between IC2601 and IC3301) and its
NO peripheral circuits.
[IC3301 TMDS input pins]
pin(AH35/AH34)(CLK-/+),
pin(AG35/AG34)(D0-/+),
pin(AG37/AG36)(D1-/+),
pin(AF35/AF34)(D2-/+).
Check the I2C line (between IC2601 and IC3301).
IC2601:pin(71)(SCL), pin(70)(SDA)
IC3301:pin(AN12), pin(AP12)
Check IC2601 and its peripheral circuits.
YES
Is the T-CON PWB connected? Check the T-CON PWB and harness.
VBO_LOCKN pin(40) of SC3801 become Low if there is no problem in NO Check IC3301 and SC3801 and their peripheral circuits in Main
the connection. PWB.
YES
Are the V-By-One HS signal input to the pin of SC3801? Check IC3301 and its peripheral circuits.(IC3501/IC3502/
VBO_CN_TXA+/-(36/37pin), VBO_CN_TXB+/-(32/33pin), NO IC3503/IC3504, etc.)
VBO_CN_TXC+/-(28/29pin), VBO_CN_TXD+/-(24/25pin).
YES
Check the panel module and harness.
6 – 16
LC-90LE740X
No audio (1)
Is INPUT-6 selected on the input select Is INPUT-5 selected on the input select
menu screen? menu screen?
NO NO
Refer to “: No external input Refer to “: No external input
video [INPUT-6]”. video [INPUT-5]”.
YES YES
Dose the audio signal come from pins (3) Dose the audio signal come from pins (3)
(L) and (4) (R) of input terminal (J514) to (L) and (4) (R) of input terminal (J509) to
pins (AP34) (L) and (AU36) (R) of IC 3301 pins (AP37) (L) and (AR36) (R) of IC 3301
(CPU) ? (CPU) ?
NO NO
Check the line between J514 Check the line between J509
and IC3301. and IC3301.
YES YES
Does the digital audio signal come from pins(AR11/AP11/AN9)(CPU_AOBCK/AOLRCK/AOSDATA0) of IC3301(CPU) to pins(6/7/5)(SP_BCLK/
SP_LRCLK/SP_DATA) of IC1703(Audio DSP)?
NO
Check the line between IC3301 and IC1703, and their paripheral circuits.
YES
• About the L/R Speakers.
Does the digital audio signal come from pins (30/21/26/27) of IC1703 (Audio DSP) to pin (5/7/8/6) of IC1902 (AMP for L/R)?
• About the Subwoofer speaker.
Does the digital audio signal come from pins (30/21/26/28) of IC1703 (Audio DSP) to pin (5/7/8/6) of IC1901 (AMP for SW)?
NO
Check IC1703 and its paripheral circuits.(X1701, etc.)
YES
• About the L/R Speakers.
Is the audio output from IC1902 as specified?
• About the Subwoofer Speaker.
Is the audio output from IC1901 as specified?
NO
• About the L/R Speakers.
Check IC1902 and its peripheral circuits.
• About the Subwoofer Speaker.
Check IC1901 and its peripheral circuits.
YES
• About the L/R Speakers.
Check the connector (P1903) L/R speakers and their peripheral circuits.
• About the Subwoofer Speaker.
Check the connector (P1904), subwoofer speaker and their peripheral circuits.
6 – 17
LC-90LE740X
No audio (2)
[PC analog audio input] INPUT-7 No audio. [HDMI analog audio input] INPUT-2 No audio.
Is INPUT-7 selected on the input select menu screen ? Is INPUT-2 selected on the input select menu screen?
NO NO
Refer to ": No external input video [INPUT-7]". Refer to “: No external input video [INPUT-2]”.
YES YES
Is the “Terminal Setting” - “Audio select” selected for “Video + Is the “Terminal Setting” - “Audio select” selected for “Video + Ana-
Audio” on the menu screen? log” on the menu screen?
NO NO
Set the HDMI audio output to "Video+Audio". Set the HDMI audio output to "HDMI+Analog".
YES YES
Does the digital audio signal come from pins(AR11/AP11/AN9)(CPU_AOBCK/AOLRCK/AOSDATA0) of IC3301(CPU) to pins(6/7/5)(SP_BCLK/
SP_LRCLK/SP_DATA) of IC1703(Audio DSP)?
NO
Check the line between IC3301 and IC1703 and their peripheral circuits.
YES
• About the L/R Speakers.
Does the digital audio signal come from pins (30/21/26/27) of IC1703 (Audio DSP) to pin (5/7/8/6) of IC1902 (AMP for L/R)?
• About the Subwoofer speaker.
Does the digital audio signal come from pins (30/21/26/28) of IC1703 (Audio DSP) to pin (5/7/8/6) of IC1901 (AMP for SW)?
NO
Check IC1703 and its paripheral circuits.(X1701, etc.)
YES
• About the L/R Speakers.
Is the audio output from IC1902 as specified?
• About the Subwoofer Speaker.
Is the audio output from IC1901 as specified?
NO
• About the L/R Speakers.
Check IC1902 and its peripheral circuits.
• About the Subwoofer Speaker.
Check IC1901 and its peripheral circuits.
YES
• About the L/R Speakers.
Check the connector (P1903) L/R speakers and their peripheral circuits.
• About the Subwoofer Speaker.
Check the connector (P1904), subwoofer speaker and their peripheral circuits.
6 – 18
LC-90LE740X
No audio (3)
No audio at UHF/VHF broadcast signal reception. No audio at digital broadcast signal reception.
Is TV selected on the input select menu screen? Is TV selected on the input select menu screen?
NO NO
Refer to “No video at UHF/VHF broadcast signal Refer to “No video at digital broadcast signal
reception”. reception”.
YES YES
Does the digital audio signal come from pins(AR11/AP11/AN9)(CPU_AOBCK/AOLRCK/AOSDATA0) of IC3301(CPU) to pins(6/7/5)(SP_BCLK/
SP_LRCLK/SP_DATA) of IC1703(Audio DSP)?
NO
Check the line between IC3301 and IC1703, and their paripheral circuits.
YES
• About the L/R Speakers.
Does the digital audio signal come from pins (30/21/26/27) of IC1703 (Audio DSP) to pin (5/7/8/6) of IC1902 (AMP for L/R)?
• About the Subwoofer speaker.
Does the digital audio signal come from pins (30/21/26/28) of IC1703 (Audio DSP) to pin (5/7/8/6) of IC1901 (AMP for SW)?
NO
Check IC1703 and its paripheral circuits.(X1701, etc.)
YES
• About the L/R Speakers.
Is the audio output from IC1902 as specified?
• About the Subwoofer Speaker.
Is the audio output from IC1901 as specified?
NO
• About the L/R Speakers.
Check IC1902 and its peripheral circuits.
• About the Subwoofer Speaker.
Check IC1901 and its peripheral circuits.
YES
• About the L/R Speakers.
Check the connector (P1903) L/R speakers and their peripheral circuits.
• About the Subwoofer Speaker.
Check the connector (P1904), subwoofer speaker and their peripheral circuits.
6 – 19
LC-90LE740X
No audio (4)
[INPUT-1 input]
Is INPUT-1 selected on the input select menu screen?
[INPUT-2 input]
Is INPUT-2 selected on the input select menu screen?
[INPUT-3 input]
Is INPUT-3 selected on the input select menu screen?
[INPUT-4 input]
Is INPUT-4 selected on the input select menu screen?
NO
Refer to “: No external input video [INPUT-1/2/3/4]”.
YES
[INPUT-1 input]
If no video appears, refer to “No external input video (HDMI) [INPUT-1]”.
[INPUT-2 input]
If no video appears, refer to “No external input video (HDMI) [INPUT-2]”.
[INPUT-3 input]
If no video appears, refer to “No external input video (HDMI) [INPUT-3]”.
[INPUT-4 input]
If no video appears, refer to “No external input video (HDMI) [INPUT-4]”.
Does the digital audio signal come from pins(AR11/AP11/AN9)(CPU_AOBCK/AOLRCK/AOSDATA0) of IC3301(CPU) to pins(6/7/5)(SP_BCLK/
SP_LRCLK/SP_DATA) of IC1703(Audio DSP)?
NO
Check the line between IC3301 and IC1703 and their peripheral circuits.
YES
• About the L/R Speakers.
Does the digital audio signal come from pins (30/21/26/27) of IC1703 (Audio DSP) to pin (5/7/8/6) of IC1902 (AMP for L/R)?
• About the Subwoofer speaker.
Does the digital audio signal come from pins (30/21/26/28) of IC1703 (Audio DSP) to pin (5/7/8/6) of IC1901 (AMP for SW)?
NO
Check IC1703 and its paripheral circuits.(X1701, etc.)
YES
• About the L/R Speakers.
Is the audio output from IC1902 as specified?
• About the Subwoofer Speaker.
Is the audio output from IC1901 as specified?
NO
• About the L/R Speakers.
Check IC1902 and its peripheral circuits.
• About the Subwoofer Speaker.
Check IC1901 and its peripheral circuits.
YES
• About the L/R Speakers.
Check the connector (P1903) L/R speakers and their peripheral circuits.
• About the Subwoofer Speaker.
Check the connector (P1904), subwoofer speaker and their peripheral circuits.
6 – 20
LC-90LE740X
If no video appears, refer to “No external input video (HDMI) If no video appears, refer to “No video at digital broadcast signal
[INPUT-1/2/3/4]”. reception”.
Is there the SPDIF signal output (CPU_ASPDIF) at pin (AR16) of IC3301 (CPU)?
NO
Check the IC3301 and its peripheral circuits.
YES
Is there the SPDIF signal (OPT_OUT) input at pin (2) of IC503 (SPDIF BUFFER & SPDIF-MUTE)?
NO
Check the line between IC3301 and IC503.
YES
Is there the MUTE signal input at pin (1) of IC503? (usual: High, Mute: Low)
NO
Check the AUDIO_MUTE and their peripheral circuits (Q505, etc.).
YES
Is there the SPDIF signal input at pin (1) of D527 (OPTICAL OUTPUT)?
YES NO
Check the speakers and the optical cable. Check D527 and its peripheral circuits.
No optical output under the following conditions as per HDMI requirements.
* Audio contents protected.
* Audio frequency beyond 48kHz.
* Audio bit length beyond 16bits.
6 – 21
LC-90LE740X
Are there the audio signal outputs at pins (AN34) (HP_MONITOR_L) and (AN3532) (HP_MONITOR_R) of IC3301 (CPU)?
NO
Check IC3301 (CPU) and its peripheral circuits.
YES
Does the audio signal come from pins (2) (MONI_HP_L) and (11) (MONI_HP_R) of IC1702 (Line-out Amplifier) to pins (3) (L) and (2) (R) of J504?
NO
Check the line between IC1702 and J504 and their peripheral circuits.
Check the LINE_MUTE line and its peripheral circuits(Q506/Q510, etc).
YES
Check the connector (J504) and their peripheral circuits, and speakers and the Cable.
No connect network
Does the signal come to 1pin of LAN-JACK J9401? NO Check the interface device and peripheral circuits.
(see fig-1, fig-2) (power-LED of hub, LINK-LED of hub)
YES
Does the signal come to AT18 pin of IC3301? NO Check the line between J9401 and IC3301.
(see fig-2) Check the LAN-JACK J9401.
YES
Check IC3301 and its peripheral circuits.
1pin
6 – 22
LC-90LE740X
CHAPTER 7. MAJOR IC INFORMATIONS Service
LC-90LE740X
Manual
7–1
LC-90LE740X
1.12. IC1703 (VHiYSS952QZ-1Y)
Audio DSP (YSS952QZ) has digital audio adjustment function (for example, PEQ, bass/treble, balance, bass enhancer, etc.) and adjusts TVs audio
quality.
7–2
LC-90LE740X
CHAPTER 8. OVERALL WIRING/SYSTEM BLOCK DIAGRAM
LC-90LE740X
Service Manual
㪧㪛㩷㪮㫀㫉㪼㩷㪟㪸㫉㫅㪼㫊㫊 㪪㪙㩷㪮㫀㫉㪼㩷㪟㪸㫉㫅㪼㫊㫊
I 㪨㪚㪥㪮㪄㪥㪈㪏㪐㪮㪡㪧㪱
㪨㪚㪥㪮㪄㪥㪈㪏㪍㪮㪡㪧㪱
㪈㩷㩷㪉 㪈㩷㩷㩷㵘㵘㪉㪋
㪉㪇㩷㩷㩷㩷㪈 㪉㪍㩷㩷㩷㪈 㩷 䇼㪪㪙䇽 䇼㪧㪛䇽 㪬㪪㪙
䇼㪪㪧䇽
䇼㪣㪈䇽 䇼㪣㪉䇽 㪈
㪌
㪉㪋
G
㪈
㪮㪦㪦㪝㪜㪩 㪬㪪㪙
㪩㪪㪧㪄㪱㪘㪌㪎㪌㪮㪡㪱㪱
㪧㪦㪮㪜㪩 䇼㪧㪛䇽
㪟㪛㪤㪠
㩷 㪈 㪤㪘㪠㪥
㪩㪬㪥㪫㪢㪙㪇㪐㪍㪮㪡㪨㪱
㪋㪈
䇼㪣㪭 䇽 㪛㪬㪥㪫㪢㪝㪐㪌㪊㪁㪁㪁㪁
F
㪟㪛㪤㪠
㪢㪜㪰
㪟㪛㪤㪠
㪛㪬㪥㪫㪢㪝㪏㪇㪇㪁㪁㪁㪁
E
㪘㪚㩷㪠㪥㪣㪜㪫
㪈
㪪㪧㩷㪮㫀㫉㪼㩷㪟㪸㫉㫅㪼㫊㫊
㪟㪛㪤㪠
㪨㪚㪥㪮㪄㪥㪈㪏㪏㪮㪡㪧㪱 㪈㪌
䇼㪩㪚䇽
㪣㪮㩷㪮㫀㫉㪼 㩷㪟㪸㫉㫅㪼㫊㫊
㪨㪚㪥㪮㪄㪤㪏㪌㪏㪮㪡㪧㪱
㪋㩷㩷㩷㪈
D
䇼㪧㪣䇽
㪫㪄㪚㪦㪥 㪋㪈
䇼㪣㪭 䇽㩷 㪜㪫㪟㪜㪩
㪛㪬㪥㪫㪢㪝㪐㪎㪌㪁㪁㪁㪁 㪈 㪬㪪㪙 㪥㪜㪫
㪝㪝㪚㩷㩿㪏㪇㫇㫀㫅㪀
䇼㪢㪤䇽
㪨㪚㪥㪮㪄㪤㪊㪍㪈㪮㪡㪨㪱 㪈 㩷㩷㩷㩷㩷㩷㩷㩷㩷㩷㪋
C
㪈 㪏㪇 㪈 㪏㪇 㵘
㪩㪚㩷㪮㫀㫉㪼㩷㪟㪸㫉㫅㪼㫊㫊
㪨㪚㪥㪮㪄㪥㪈㪏㪎㪮㪡㪧㪱
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19
8–1
LC-90LE740X
[2] SYSTEM BLOCK DIAGRAM
+0276 %8$5A5+&'A+0
%8$5.4
/KPK2NWI %8$5A5+&'A+0A.4
8$1A.1%-0
8$1A*62&0
+%A4'#&;
20.A'0 0A20.A'0
20.A92
1(.A(4%456
H
ޣ.8ޤ5%
R
/*\
䇼㪪㪧䇽 ::
:VCN +%A
-*\ +%A
-*\
8
52'#-'4 㪧㪈㪐㪇㪊 +% #/2A#A.4
㪜㪯㪫㪄㪪㪧 52#/2
%*
8
;&#
+% +%
8
䇼㪪㪧䇽 #/2A.4%-$%.-/%.-
&52 ''241/
9QQHGT 㪧㪈㪐㪇㪋 +%
8
;55 MDKV
㪜㪯㪫㪄㪪㪧 9QQHGT#/2
%* #/2A#A59
+% 6WPGT
;&# 4GUGV EKTEWKV
8
7%1/A456
8 +% #06
8A59
%0 .0$A5*146 $7
8
2 &'6A20.8
#/2A*122 *2A/76' %QPPGEVQT 4'5'6 +1 +1
4Z&6Z&
0A2'4A456 0A2'4A456 HQT2TQITCO &)$2A4:&6:& +1 .4A4'(
#/2A/76' 0A#/2A2416'%6 7RFCVGCPF 85;0%
G 0A#/2A2416'%6
52A/76'
'OWNCVG /1&' +% +1
7%1/A/1&' 4%% 6*'4/1 6JGTOKUVGT
#&
)52A29/
29/
#7&+1A/76' #7&+1A/76' +:&9,
M*\ : 57$/%7 ''241/A5%.5&#
+%
:VCN
/WVG $7
8
/*\ (.
%8$5A1WV
$7
8
8D[1PG176
%8$5
%QORQPGPV
EKTEWKV :VCN +%
92 ''241/
8 +1
2/A4'3 MDKV
8 +1
8 0A/76'A#A#.. .#/2A'44
&A+(
&A+(
8 +1
+1 56$
+(A#)% +(A#)% %27A6:&A7%1/%27A4:&A7%1/ 7#46
0A54'5'6 +1 #%A&'6
+1 +1
*&/+A%'%A+0
+1 5/219
*&/+A%'%A176
29/
+%
+1
#&
+%
+1
25A10
F 0A670A456 0A670A456
5/219*1.&
4%12%
+%
5GNGEV
4%A%27 )0&
67A&'/1&A5%.5&#
-*\8
670'4A+% 4%
+%A
-*\8
+%A
+%A
-*\8
+4A2#55
+%A
4(+0
8
8 2%A85;0%*5;0% +%
+%
8
#7&+1A/76'
5+)0#.241%'55 4)$*8 +% +%
*2A/76'
5$' 2%A4)$ 810
56$A%27
8 4)$KP +1
+%
8 /6
(*&
8
4* &&%A+%A 29/A 1(.
TU1104Analog/ *&/+A *8% 1(.
+%
5RNKVGT
Digital 29/A
&KIKVCN#8FGEQFG/CKP%27 *%)&2
Si Tuner #%A&'6
E
2
R
.4A4'(
20.A219
+5
5#.4%-5%.- +%
8
/*\
5RNKVGT
ޣ2&ޤ219'4˴2
: *%)&2
#WFKQQWV : VCN
&KUENGVG 20.A+%A'0
#7&+1A/76' *2/10+A.4
29/
#WFKQ1WV
/WVG
8 +%
/KPK2NWI 5+( &&4
/
*2/10+A.4 +%
5%.A56$A%27
-';5&#A56$A%27
-';
)DKV
&&4
/
#%A&'6
20.A219
)DKV
25A10
126+%#.
5&+1%/&5&+1%.-
0#0&(NCUJ
10&&㨪
10&#㨪
&
8 $7
8
*&/+A#4% &6852&+(
7#466:&
7#464:&
7#466:&
)DKV
52+A(.#5*
7#464:&
&
8
7#46
\\
75$A
75$A
75$A
˴/
8
5&+㨪
&57$ 2%A85;0%*5;0%
75$A
219A594'3
.4A27.5'
14'5'6
G//%
4)$ 2%A4)$ 4'5'6
4%12%
$CEM7R
4'5'6
$7
8 $7
8
$7
8
+%
㪠㪚㪌㪇㪍 56$
8
+%
7#46A%2761%7#46A%61%27
5GNGEV
8
8 +%
5GNGEV
㪩㪪㪉㪊㪉㪚㩷㪫㫏㪩㫏 219'4%+4%7+6
45% $WHHGT
㪤㪊㪉㪉㪈㪜㪠㪧
0QRKP4%2CUUVJTQWIJ
+0276*&/+ &&%A
8
*&/+A
8 +%
#4%
8 0A54'5'6
5/219*1.&
C +0276*&/+ &&%A
&8+ *&/+A
*&/+A%'%A176
*&/+A%'%A+0
+% +%
8
+0276 &&%A
*&/+59 0#0&(.#5*
*&/+ *&/+A
5++# )DKV +%A
8 +% 78
-*\
&KUENGVG 2QYGT59
+0276*&/+ /*. $&) &&%A
/*. *&/+A
$7
8 6T
&&%A +%
*&/+A $WHHGT
'0A4294A0'0A8$758$75A1%/*.A&'6 .%:(6
*&/+A%'%
8
B 7%1/A/*.A%$75/*.A&'6A219
/*.A9#-'72
8
748 $7
8
#016*'4A9#-'72
75$A&20 ޣ4%ޤ2
R
75$ ,
75$
8 +% 78
2QYGT59 ޣ+4
ޤR ޣ6-ޤ2
R ޣ4#ޤ2
R ޣ%+ޤ2
R
#
$&)
75$A&20
,
75$
8
75$ +% 78
# 2QYGT59 &+4 6#%6-'; 4% '/$.'/
25&$
75$A&20
75$ , 4%
75$
8 +% 78 12%
A # 2QYGT59
$&)
,
'VJGTPGV
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19
8–2
PartsGuide
LC-90LE740X
PARTS GUIDE
No. SY2A4LC90LE74
MODEL LC-90LE740X
CONTENTS
Parts marked with " " are important for maintaining the safety of the set. Be sure to replace these
parts with specified ones for maintaining the safety and performance of the set.
2
LC-90LE740X
[3] CABINET AND MECHANICAL PARTS
20 43
55 48
4-5
4 46
45
4-5
8 4-3
4-2 9
11
44 4-6
20 38
39
KEY 4-4 3-3
KM Unit
10
3-3 3
4-5
4-1 17 43
25-3
47 3-4 3-3 2-2
25-2 44 20
25-1
44
SB 19
19 2
MAIN PD 3-3 2-2
Unit 25
12 25-1 3-1
25-4 3-2 2-3
37
28 12-3 SP 2-1
33
21
G 12-2 12-1 30 SP
35 2-2
41
SB
32
44
RC LW
18
41
21
J 36
18
7
13 13
C
7
13
42
14
16 15
15
90" LCD Panel
Module Unit 14
1 PL 16 13
LW
1-14 16 16
1-1
1-14
1-8 1-14
R/C LED 31
1-8 Unit L2
1-8 1-14
PL
L1
1-6 1-1 1-14 1-4 F
1-15 RA PD L2
1-14
1-14
RC L1
1-1
1-2 G
1-9 CI CI
1-5 1-11 POWER/DRIVE
54 1-7 KM RA
EMBLEM Unit
Unit 3D IR 19
1-14
F
Unit
1-3
51
1-1
1-13
52
53
50
49
3
LC-90LE740X
4
LC-90LE740X
[4] SUPPLIED ACCESSORIES/PACKING PARTS (NOT REPLACEMENT ITEM)
X1
X2 • X8 Operation manual
Stand Base Ass'y
Support Ass'y
• X10 Antenna Adaptor
• X12 Skype Information sheet
X3
Screw
X4
X5
X6
S5
S7
X2
X7
X9
X3
X12
S7 X8
X10
S11
S7
X1
S9
S10
S3
S1
S8 S9
S8
S8
S2
S6
S16
S4
5
LC-90LE740X
6
LC-90LE740X
LC-90LE740X
SHARP CORPORATION
Digital Information Appliance Group
Dec. 2012 CS Promotion Center
YK. DS Yaita,Tochigi 329-2193, Japan