Professional Documents
Culture Documents
TEMPER® may be used as heat transfer fluid in both static and mobile
installations
TEMPER® is a ready-to-use solution and never has Colourless liquid (lightly yellowish), TEMPER®
to be diluted. contains neither amines nor nitrites.
Available in 5 versions (mixtures) of which the descriptions indicate the freezing point:
TEMPER® has increased thermal capacity and is In enclosed packaging and closed systems,
characterised by excellent thermal conductivity in TEMPER® is stable and lasts long and is, in
comparison with the products with a glycol principle, unlimited.
propylene base.
The special additives present in TEMPER® ensure
The viscosity is lower than in the glycols, it is as strong optimum anti-corrosion and lubricating
in small pumps and pipes. The investment costs for specifications.
the installation and the usage of the system are
therefore lower.
1/6
TEMPER®
1. T E M P E R ’ S ® PHYSICOCHEMICAL PROPERTIES
2/6
TEMPER®
3/6
TEMPER®
Figure 1 Figure 2
Temper® contains special corrosion inhibitors which The corrosion inhibitors of Temper® practically do
do not form a general protective film, but act only not wear out.
where there are differences in the electricity Once the corrosion risk is blocked and
potential. compensated, the molecules of the inhibitors are
The molecules of the inhibitors are only deposited freed in the Temper® and can once again be
in the areas where there is risk of corrosion, and deposited in other places where there is a
form an extremely thin layer which makes difference in electricity potential (see figure 2).
practically no change to the thermal transfer.
4/6
TEMPER®
It is strongly recommended to start cleaning the Please note: If there are tartar deposits on the
installations thoroughly before filling them with installation and it is seriously oxidised with scales, it
Temper®. is advisable to first treat the circulation with a
solution of "désoxydant P*" at approximately 100
If they have very many deposits and especially g/l of water at 50°C for 2 hours.
metal oxides, clean with Dispersant D. After it has been emptied, follow the treatment with
"dispersant D*" in the abovementioned manner.
It is to be done in the following manner:
- make the circuit circulate water for 1 to 2 hours, In principle, the current installations containing
then drain the installation quickly and fully to the other heat transfer fluids may be re-adapted for the
lowest point. Temper®.
- prepare and put "dispersant D*" solution at 20 One generally achieves a net power increase,
g/litre of water in the installation thanks to the improved properties of the Temper®
- let the product circulate for at least 2 hours and thermal transfer.
then drain the installation very quickly to the Before changing to Temper®, it is essential to
lowest point; control, check and adapt, if necessary, the
- adequately and carefully rinse with water until it is compatibility of the pumps, taps, material and
clear and the pH is approximately 7 (± 0.5). accessories of the installation.
- The system must then by dried quickly (by
emptying or with nitrogen), then fill from the The system must then be treated with a cleaning
lowest and carefully drained point. product strong enough to eliminate the old
corrosion inhibitors, then rinsed with neutral pH
Depending on the state of the circuit, it may be distilled water.
necessary to clean several times. The sieves and filters (recommended mesh 0.6-0.8
It is important to drain and carefully rinse with mm) must be cleaned/replaced.
water after every time it has been cleaned.
Temper® may then be put into the installation to be
restarted again.
5/6
TEMPER®
Filters
Pumps
* The data stated in paragraph 1 of this document are merely indicative and do not constitute a sales specification.
Réf. : CA.24/06.08/V1/ GB
The information contained in this product sheet is the result of our studies and experience. It is provided in good faith, but should not, under any
circumstance, be taken to constitute a guarantee on our part or an assumption of our responsibility. This is particularly the case when third party rights are
at stake or in situations where a user of one of our products fails to observe applicable regulations.
Direction and departments: 26, avenue du Petit Parc - 94683 Vincennes Headquarters: 4, rue de la Croix-Faubin - 75011 Paris
Cedex
Tel. : 01 43 98 75 00 – Fax : 01 43 98 21 51E-mail : www.climalife.dehon.com
Corporation with Executive and Supervisory Board at a capital of 5.100.000 €- 310 259 205 CTR Paris
6/6