Professional Documents
Culture Documents
目录
Disclaimer
Thank you very much for using our products! Please ensure that the product is used in accordance
with local laws and regulations. The company will not bear any legal liability for any result or loss
caused by illegal use, installation or modification of the product. Please use the product carefully
according to the procedure and matters needing attention in this manual. If the product is damaged
due to disassembly, collision, unconventional operation and other human factors, the company
will not provide replacement or free maintenance services.
The copyright of this manual belongs to Shenzhen Xingkai Tech Co., LTD. Reproduction in
any form shall not be allowed without permission.
Precautions
In order to ensure the correct use of this product and the best use effect, before operating this
product, please be sure to read this manual carefully, follow the relevant operating procedures and
precautions, avoid the damage of equipment or poor use effect due to improper operation or use.
Operators should have a certain basic knowledge of communication electronics. Please pay
attention to the following matters when installing and using this product:
Installation note:
1. Before power on the transmitter, load such as transmitter antenna or attenuator must be
installed to the RF output interface; otherwise, the power amplifier module inside the
transmitter will be damaged.
2. When replacing the transmitting antenna, the power must be cut off first, otherwise the power
amplifier module inside the transmitter will be damaged.
3. Try to match the transmitting antenna with the transmitter (including impedance, frequency
and power), otherwise it may cause damage to the power amplifier module inside the
transmitter.
4. Please use DC8V~DC30V dc power supply to power the transmitter, otherwise the circuit
may be damaged or the transmitter may work abnormal.
5. The installation of transmitting antenna should be exposed in the air as far as possible to
avoid obstructions, otherwise the communication distance will be affected.
6. Installation of transmitting antenna should be as far away from large metal devices as
possible.
2
深圳市兴恺科技有限公司
7. Try to keep a certain distance between the transmitter and other electronic devices to reduce
electromagnetic interference between devices.
1.General Introduction
XK-F311E Broadband Digital Datalink
Point to Multi-Points
Two-way communication: Video, telemetry, remote control transmission 3 in 1
One-way video transmission channel
Two-way telemetry transmission channel
One-way remote control channel
500mW~up to 2W
Interface: Hdmi, Ethernet, Sdi, USB, Serial, PPM/S.BUS
Frequency: Customizable
ARQ retransmission and adaptive frequency hopping
With low power consumption and long communication distance. It supports
simultaneous transmission of network data encoded by high-definition cameras, flight
control data, pan/tilt control data, and remote control data.
With encryption function, users can set the channel encryption key independently.
Supports transparent transmission protocol, which can transmit flight control and
other mounted data information at the same time. The ground unit can exchange data
with the ground station through serial port or network port (UDP/TCP). Support serial
port, Sbus transparent transmission function.
2.2 Functions
3.Technical Parameters
Spec/Parameters
Item
Air Unit Ground Unit
Operation Voltage DC8V~DC30V,Standard input DC12V
Power Consumption 9W 7W
Modulation OFDM
FEC 1/2、2/3、3/4、5/6
Constellation BPSK、QPSK、16QAM
Duplex TDD
1.400GHz-1.495GHz, 2.4GHz-2.483GHz,
Frequency
(Customizable)
Tx Power ≤27dB(ok to set)
Bandwidth 10MHz 2.5MHz
Latency 3ms~8ms
Data interface UART(TTL/RS232)/SUBS
Serial port rate 115200bps
Downlink
2 Mbps~15 Mbps(10MHz)
Throughput
Working temperature -20℃~55℃
Storage temperature -20℃~75℃
Working humidity 10%~90%
Antenna 2dBi 5dBi
Dimensions 102*55*26mm
Weight ≤160g
4
深圳市兴恺科技有限公司
5
深圳市兴恺科技有限公司
4.2 Interface
5 Installation connection
5.1 Installation and connection of the Air unit
6
深圳市兴恺科技有限公司