Professional Documents
Culture Documents
---------------------------------------------------------------------------
Table of Contents
---------------------------------------------------------------------------
1. Release Files
2. History
---------------------------------------------------------------------------
1. Release Files
---------------------------------------------------------------------------
Date Time Size File Name Version
2013/10/17 18:42 13KB K2026090.mem 2.0.2.6
---------------------------------------------------------------------------
2. History
---------------------------------------------------------------------------
---------------------------------------------------------------------------
Version 2.0.2.6 : November 12, 2013
---------------------------------------------------------------------------
- Fixed the following three problems which occur with enabling the Debug
Port function.
1. The yellow bang comes up on RENESAS USB 3.0 Host Controller in the
device manager after S3/S4 Resume and restarting PC.
---------------------------------------------------------------------------
Version 2.0.2.4 : June 7, 2013
---------------------------------------------------------------------------
- The following problems were fixed.
1. The performance of some USB2.0 Card Readers decreased.
This problem occurs from 2.0.1.3 to 2.0.2.0.
2. The yellow bang comes up on RENESAS USB 3.0 Host Controller in the device
manager after restarting PC with the following conditions.
[Conditions]
a)BC_MODE_PX fields of PHY Control 2 Register set to the following values:
0010b : SDP - DCP
0011b : CDP - DCP
0100b : SDP - FVO1
0101b : CDP - FVO1
0110b : SDP - FVO2
0111b : SDP - FVO2
b)The asserted timing of PERSTB is equal to or lower than 500ms.
3. There is a possibility that "Sleep and PNP (disable and enable) with IO
before and after" test in Windows8 HCK fails when "Allow the computer to
turn off this device to save power" of Power Management tab of Device
Manager is enabled.
##Note##
The specific USB3.0 HDD comes with a USB3.0-SATA bridge device having the bug
that it's Rx-Termination is not in high impedance state while its power plane
is stabilizing. This means that the device does not meet the USB3.0
specification
(6.11.2 Rx Detect sequence) as follows:
---------------------------------------------------------------------------
Version 2.0.2.0 : November 29, 2012
---------------------------------------------------------------------------
- The following problem was fixed.
1. In Linux environment, there is a possibiity that some USB3.0 devices
are not detected after the PC connected with them has booted up.
We have not seen this problem in Windows environment.
---------------------------------------------------------------------------
Version 2.0.1.8 : September 7, 2012
---------------------------------------------------------------------------
- The following problems were fixed.
1. Added the function for changing the configuration of "Completion
Timeout Disable" bit in PCI Configuration space.
Please see the release note & readme file of ROM Write tool in more
detail.
---------------------------------------------------------------------------
Version 2.0.1.7 : July 19, 2012
---------------------------------------------------------------------------
- The following problems were fixed.
1. On the system enabled with PCIe ASPM-L1 function and connected with
some USB devices, PCIe bus reaches Link Down and the USB communication
unexpectedly stops in rare condition.
2. Once the firmware of version 2.0.1.3 is stored in the serial ROM with
uPD720202, the FW cannot be erased and updated with the ROM Writing tool
for DOS V.2.0 or older.
---------------------------------------------------------------------------
Version 2.0.1.3 : June 15, 2012
---------------------------------------------------------------------------
- The following problems were fixed.
1. There is a possibility that the USB 3.0 Host controller cannot notify
the xHCI Driver when the Host controller receives the following contiguous
Device Notification Transaction Packets: Function Wake Notification,
Latency Tolerance Message (LTM) Device Notification, Bus Interval Adjustment
Message Device Notification.
We have never seen this problem on a real system.
3. The yellow bang comes up on RENESAS USB 3.0 Host Controller in the device
manager after the ver 2.0.1.1 or older FW is written by using "Serial
ROM Write Tool for Windows" without Power On Reset process.
This issue doesn't occur when the Serial ROM is blank.
- Additional remediation was implemented for the following ver 2.0.0.6 issue:
---------------------------------------------------------------------------
Version 2.0.1.1 : March 12, 2012
---------------------------------------------------------------------------
- The following problems were fixed.
1. When the following devices are connected with a High-Speed HUB in the
device tree for the USB3.0 host controller, there is a possibility of
failing to schedule split transactions. This causes all of the devices
in the topology to fail further communication with the host.
[Conditions]
1. Devices having one or more Full-Speed ISO (isochronous) endpoint
2. Devices having one or more Full-Speed or Low-Speed INT endpoint
3. Total of the maximum packet size of each endpoint of condition 1
and 2 exceeds 564bytes.
2. When debug port function is running in Windows 8 and hot-plug is done
between host system and target system, the yellow bang comes up on the
debug port driver in the Device Manager of Windows 8.
---------------------------------------------------------------------------
Version 2.0.1.0 : February 1, 2012
---------------------------------------------------------------------------
- Modified the FW structures for FW download function.
There is a possibility that the yellow bang will appear on the "Renesas
Electronics USB3.0 host controller" driver in the device manager of the
Windows OS, or xHCI driver in the system bios, or other OS halts.
This problem does not occur when the FW is loaded from a Serial ROM.
---------------------------------------------------------------------------
Version 2.0.0.6 : October 24, 2011
---------------------------------------------------------------------------
1. Modified the problem that a yellow bang appears in Device Manager Windows OS
when the PC boots without connecting USB devices into the USB3.0 port, or
the USB3.0 host controller drivers are disabled and enabled in Device Manager.
2. Modified the problem that can cause the StopEndpoint command time-out error.
3. Modified the problem that cannot process the any commands when USB 3.0 Host
controller behaves as the debugport.
4. Modified the problem that cannot detect a USB 2.0 devices when USB 3.0 Host
controller drivers are disabled and enabled in device manager while connecting
a USB 2.0 Device into USB3.0 port.
---------------------------------------------------------------------------
Version 2.0.0.3 : September 8, 2011
---------------------------------------------------------------------------
- First Release for uPD720201/uPD720202 ES 2.0 sample & CS sample & Mass
product whose revision ID of PCI Configuration Register is 2h.
---------------------------------------------------------------------------