Professional Documents
Culture Documents
Spreadsheets To BS 8110 Etc: The Concrete Centre
Spreadsheets To BS 8110 Etc: The Concrete Centre
DIMENSIO (mm)
H= 3000 B= 3500 Tw = 225
Hw = 0 BI = 150 Tb = 350
He = 2500
SOIL PROPERTIES
Design angle of int'l friction of retained mat'l (Ø) = 30 degree
Design cohesion of retained mat'l (C ) = 0 kN/m2 (Only granular backfill considered, ie "C" = 0)
Density of retained mat'l (q ) = 20 kN/m3
Submerged Density of retained mat'l (qs ) = 13.33 kN/m3 (default=2/3 of q), only apply when Hw >0
Design angle of int'l friction of base mat'l (Øb) = 20 degree = 20.00
Design cohesion of base mat'l (Cb ) = 0 kN/m2 ASSUMPTIONS
Density of base mat'l (qb ) = 10 kN/m3 a) Wall friction is zero
Allowable gross ground bearing pressure (GBP) = 150 kN/m2 b) Minimum active earth pressure = 0.25qH
LOADINGS (unfactored) c) Granular backfill
Surcharge load -- live (SQK) = 10 kN/m2 h) Design not intended for walls over 3.5 m high
Surcharge load -- dead (SGK) = 10 kN/m2 i)Does not include check for temp or shrinkage effects
Line load -- live (LQK) = 15 kN/m
Line load -- dead (LGK) = 20 kN/m
Distance of line load from wall (X) = 250 mm
Wall load -- live (WQK) = 50 kN/m
Wall load -- Dead (WGK) = 50 kN/m
1) Wall idealised as a propped cantilever ( i.e. pinned at top and fixed at base )
2) Wall is braced.
3) Maximum slenderness of wall is limited to 15, i.e [ 0.9*(He-Tb/2)/Tw < 15 ]
4) Maximum Ultimate axial load on wall is limited to 0.1fcu times the wall cross-sectional area
5) Design Span (Effective wall height) = He - (Tb/2)
6) -ve moment is hogging ( i.e. tension at external face of wall )
+ve moment is sagging ( i.e. tension at internal face of wall )
7) " Wall MT. " is maximum +ve moment on the wall.
8) Estimated lateral deflections are used for checking the PD effect .
Force Lever arm Base MT. Wall MT. Reaction at Reaction at Estimated Elastic
Lateral Force (kN) to base (m) (kNm) (kNm) Base (kN) Top (kN) Deflection D (mm)
PE = 26.98 0.78 -10.11 4.14 23.15 3.82 0.2
PS(GK) = 11.62 1.16 -4.68 2.54 8.50 3.13 0.2
PS(QK) = 11.62 1.16 -4.68 2.54 8.50 3.13 0.1
PL(GK) = 10.00 2.12 -3.32 4.48 3.69 6.31 0.1
PL(QK) = 7.50 2.12 -2.49 3.36 2.77 4.73 0.0
PW = 0.00 0.00 0.00 0.00 0.00 0.00 0.0
Total 67.73 -25.28 17.06 46.61 21.12 0.6
Vertical FORCES (kN)Lever arm (m) Moment (kNm) BEARING PRESSURE (kN/m²)
Wall load = 100 1.49 148.75
0
Wall (sw) = 14.31 1.49 21.29
Base = 29.40 0.00 0.00
50
Earth = 6.45 1.68 10.80
Water = 0.00 1.68 0.00
100
Surcharge = 1.50 1.68 2.51
Line load = 20.00 0.00 0.00
150
å V= 171.66 å Mv = 183.35
200
MOMENT due to LATERAL FORCES, Mo = -18.11 kNm
SLIDING AT BASE (using overall factor of safety instead of partial safety f F.O.S = 1.50
CHECK CRACK WIDTH IN ACCORDANCE WITH BS8100/Temp & shrinkage effects not included
X= 60.69 mm e m = -0.00109 BS8007
Acr = 115.54 mm W= -0.25 mm < 0.30 OK App. B.2
NO CRACKING
CHECK CRACK WIDTH IN ACCORDANCE WITH BS8100/Temp & shrinkage effects not included
X= 60.69 mm em = -4E-05 BS8007
Acr = 115.54 mm W= -0.01 mm < 0.30 OK App. B.2
NO CRACKING
XX= 0
IF(ECCY>(B/1000)/6,IF(XX>(B/1000/2-ECCY)*3,0,(((B/1000/2-ECCY)*3-XX)/((B/1000/2-ECCY)*3))*BP),((VL/(B/1000)*(1-(6*ECCY)/(B/1000))))+(B/1000-
XX)/(B/1000)*(BP-(VL/(B/1000)*(1-(6*ECCY)/(B/1000)))))
IF(ABS(ECCY)>(B/1000)/6,IF((B-XX)>(B/1000/2-ABS(ECCY))*3,0,(((B/1000/2-ABS(ECCY))*3-(B-XX))/((B/1000/2-ABS(ECCY))*3))*BP),((VL/
(B/1000)*(1-(6*ABS(ECCY))/(B/1000)))) +(B/1000-(B-XX))/(B/1000)*(BP-(VL/(B/1000)*(1-(6*ABS(ECCY))/(B/1000)))))
IF(ABS(ECCY)>(B/1000)/6,IF(XX>(B/1000/2-ABS(ECCY))*3,0,(((B/1000/2-ABS(ECCY))*3-XX)/((B/1000/2-ABS(ECCY))*3))*BP), ((VL/(B/1000)*
(1-6*ABS(ECCY))/(B/1000))))+(B/1000-XX)/(B/1000)*(BP-(VL/(B/1000)*(1-(6*ABS(ECCY))/(B/1000)))))
145.3407
145.3407
0 0.00 145.341 0 145.34 0.0700 10.17 1.17 0.07 10.17 0 0.00
1 0.07 141.034 BEARING
M PRESSURE DIAGRAM 1 141.03 0.07 9.87 0.44 0.07 9.87 0 0.00
00
42
84
26
68
10
52
94
36
0.
0.
1.
1.
2.
2.
2.
3.
0
3 0.21 132.420 3 132.42 0 0.00 0.00 0.07 9.27 0 0.00
4 0.28 128.113 4 128.11 0 0.00 0.00 0.07 8.97 0 0.00
KN/M^2
MOMENTS SHEARS
MTE2= 0.64 SE2=IF(YY>=(L-'ANALYSIS & STABILITY'!M28),Ka*(q-QS)*(YY-(L-'ANALYSIS & STABILITY'!M28))^(2)/2
YY= 3.875 MTE1= -49.26 -5.84 95.327
MTLG= -7.20 31.65
MTLQ= -5.40 23.74
MTSG= -16.36 37.539
MTSQ= -16.36 37.54
MTW= -1.93 1.12
UTM= ###
###
0 0.00 0 0.00 0.000
MOMENTULT.
DIAGRAM
1 0.06 1.7595 0.06 MT (KNM) 1.759 1.759 0.00 0.00
2 0.11 3.519 0.11 -40 -30 -20 -10 0 10 20 30 3.519 1.759 0.00 0.00
0.00
3 0.17 5.2785 0.17 5.278 1.759 0.00 0.00
0.11
4 0.23 7.0379 0.23 0.23
7.038 1.759 0.00 0.00
5 0.28 8.7974 0.28 0.34 8.797 1.759 0.00 0.00
6 0.34 10.557 0.34 0.45 10.557 1.759 0.00 0.00
7 0.40 12.316 0.40 0.57 12.316 1.759 0.00 0.00
0.68
8 0.45 14.076 0.45 14.076 1.759 0.00 0.00
0.79
9 0.51 15.835 0.51 15.835 1.759 0.00 0.00
WALL (M)
0.90
10 0.57 17.563 0.57 1.02 17.563 1.728 0.00 0.00
11 0.62 19.239 0.62 1.13 19.239 1.677 0.00 0.00
12 0.68 20.863 0.68 1.24 20.863 1.624 0.00 0.00
1.36
13 0.73 21.788 0.73 21.788 0.925 0.00 0.00
1.47
14 0.79 21.828 0.79 1.58
21.828 0.040 21.83 0.79
15 0.85 21.808 0.85 1.70 21.808 -0.020 0.00 0.00
16 0.90 21.724 0.90 1.81 21.724 -0.084 0.00 0.00
17 0.96 21.574 0.96 1.92 21.574 -0.150 0.00 0.00
2.03
18 1.02 21.356 1.02 21.356 -0.218 0.00 0.00
2.15
19 1.07 21.066 1.07 2.26
21.066 -0.289 0.00 0.00
20 1.13 20.704 1.13 2.37 20.704 -0.363 0.00 0.00
21 1.19 20.265 1.19 2.49 20.265 -0.439 0.00 0.00
22 1.24 19.747 1.24 2.60 19.747 -0.517 0.00 0.00
2.71
23 1.30 19.149 1.30 19.149 -0.599 0.00 0.00
2.83
24 1.36 18.467 1.36 18.467 -0.682 0.00 0.00
25 1.41 17.699 1.41 17.699 -0.768 0.00 0.00
26 1.47 16.842 1.47 16.842 -0.857 0.00 0.00
MOMENT DIAGRAM
27 1.53 15.894 1.53 ULT. MT (KNM) 15.894 -0.948 0.00 0.00
-40 -30 -20 -10 0 10 20 30
28 1.58 14.852 1.58 14.852 -1.042 0.00 0.00
0.00
29 1.64 13.714 1.64 0.11 13.714 -1.138 0.00 0.00
30 1.70 12.477 1.70 0.23 12.477 -1.237 0.00 0.00
0.34
31 1.75 11.139 1.75 0.45 11.139 -1.338 0.00 0.00
32 1.81 9.6967 1.81 0.57 9.697 -1.442 0.00 0.00
0.68
WALL (M)
Geometry
0 0
0 350
150 350
150 3150
3500 3150
3500 2850
375 2850
375 3150
375 350
3500 350
3500 0
0 0 3150 3500
Project Spreadsheets to BS 8110 etc
Location Grid line 2 CRACK WIDTH CALCULATIONS
Basement wall design to BS8110:2005 Made by rc Job No R68
Originated from 'RCC61 Basement Wall.xls' v4.0 © 2006 TCC Date 16-Nov-20
WALL
MR= 15.06 MS= 399 Asreq = 652 fs = 216.166 sprov%= 0.568
As/bd= 0.006 MSS= 549 Assreq = 423 fs = 249.45 sprov%= 0.3159
X= 59.61 MSBB= 762 ASBBreq= 13 fs = 8.81311 sprov%= 0.1653
Ic= 279184778 MSBT= 762 ASBTreq= 315 fs = 209.118 sprov%= 0.1653
STS= 0.000800
ST1= 0.001128
ST2= 0.00038631
Acr= 102.923397
W= 0.13
e m= 0.0007
This spreadsheet should be used in compliance with the accompanying publication 'User Guide
RC Spreadsheets: v4' available from The Concrete Centre www.concretecentre.com/rcdesign Tel
+44 (0)1276 606800
Status of spreadsheet This spreadsheet is shareware but may not be used for commercial purposes
Public release version. until the user has registered with The Concrete Centre using the licence
validation form available on The Concrete Centre website
www.concretecentre.com/rcdesign
Revision history RCC61 Basement Wall.xls