Professional Documents
Culture Documents
[1]
F-14-28
imagePRESS C6010 / imagePRESS C7010VP / imagePRESS C6010VP / imagePRESS C7010VP FS / imagePRESS C7010VP PSU / imagePRESS C6010VP FS
/ imagePRESS C6010VP PSU / imagePRESS C6010 FS / imagePRESS C6010 PSU
[1] [3]
[2]
F-14-29
4) While holding the harness [1], hold the grip [2] and pull the Process Unit [3] until it stops.
[1]
[3]
[2]
F-14-30
5) When pulling out the process unit, check to see that there is no toner spattering around the [A] area. If there is toner around the [A] area, remove it with a lint-
free paper.
14-45
Chapter 14
[A]
F-14-31
CAUTION:
Points to Note When Setting in Process Unit
When setting the process unit [1], let the edge of the harness [2] upward and
push it to avoid being caught in the process unit.
[2]
[1]
6) Prepare the Shutter open tool [2] which is included in the host machine to install to the Shutter Solenoid Shaft at rear of the Process Unit [1].
NOTE:
Since cleaning of the Drum Patch Sensor is performed while the Drum
Patch Sensor Shutter is open, install the Shutter open tool [2] to the Shutter
Solenoid Shaft at rear of the Process Unit [1].
14-46
Chapter 14
[2]
[1]
F-14-32
7) Insert the Shutter Open Tool [3] between the Solenoid Sensor Flag [1] and the Solenoid Stopper Plate [2] with the U-shaped groove [4] of the Shutter Open Tool
[3] aligned with the Solenoid Shaft [5].
[2]
[3]
[5]
[4]
[1]
F-14-33
The Process Unit (C/Bk) is shown in the figure.
14-47
Chapter 14
[2]
[3]
[5]
[4]
[1]
F-14-34
[1]
[A]
14-48
Chapter 14
[1]
[A]
- After installing the Shutter Open Tool [1], hold the top side [A] and move
it to the right and left to check that the Shutter Open Tool [1] is secured. If
the Shutter Open Tool [1] comes off only by moving it to the right and left,
the U-shape groove [2] of the Shutter Open Tool [1] is not correctly installed
to the Solenoid Shaft. Perform step 7 again.
[1]
[A] [A]
14-49
Chapter 14
[1]
[A] [A]
CAUTION:
- Since there is a difference in level between the case of the Drum Patch
Sensor and the surface of the sensor, it is difficult to reach the sensor surface
with lint-free paper. Be sure to fold an end of the lint-free paper as shown in
the figure and use the end [A] to clean the sensor surface.
[A]
- When cleaning the sensor surface [A], be sure not to wipe the Shutter Film
[B]. Otherwise the Drum Patch Sensor Shutter Film may be deformed.
[B] [A]
9) Clean the surface [A] of the Drum Patch Sensor with lint-free paper moistened with alcohol.
CAUTION:
Be sure not to dry wipe with lint-free paper; otherwise, toner is attracted by
static electricity.
14-50
Chapter 14
[A]
F-14-35
10) Clean the surface [A] of the case of the Drum Patch Sensor with lint-free paper moistened with alcohol.
[A]
F-14-36
11) Remove the Shutter Open Tool [1] attached in step 7.
14-51
Chapter 14
[2]
[1]
[3] [4]
imagePRESS C6010 / imagePRESS C7010VP / imagePRESS C6010VP / imagePRESS C7010VP FS / imagePRESS C7010VP PSU / imagePRESS C6010VP FS
/ imagePRESS C6010VP PSU / imagePRESS C6010 FS / imagePRESS C6010 PSU
NOTE:
Clean the Developing Assembly of each color in the same way.
F-14-37
CAUTION:
Be careful not to damage the 2 Scraper Sheets [1].
14-52