Professional Documents
Culture Documents
settings
0
CART EUR EN
Lathe Chucks
Lathe Chucks
Lathe Spindle Nose Mounting Systems
To determine which type of spindle nose mounting your lathe requires, consult the diagrams below, then read the chart beneath the appropriate diagram. Make the
measurement required. This will give you the exact type of mounting for the lathe spindle nose.
American Standard Type D1 - Camlock
The Type D1 Camlock mounting is used on lots of Engine Lathe spindles. Each pin on the chuck side has a "D" shape cutout. For quick measurement, measure from center
of spindle to center of pin, “D” (D=1/2F). When mounting, you use your chuck key to rotate a cam in the spindle side that pulls the pin in snug.
https://toolsmach.com/en/content/15-lathe-chucks 1/7
5/8/2020 Lathe Chucks
A1
A1
C
Spindle nose size A B max D E1 F1 E2 F2
-0.025
A1 - 5 133.4 82.575 14.288 22.2 11x7/16-14 UNC 104.8 8x7/16-14 UNC 61.9
A1 - 6 165.1 106.390 15.875 25.4 11x1/2-13 UNC 133.4 8x1/2-13 UNC 82.6
A1 - 8 209.5 139.735 17.462 28.6 11x5/8-11 UNC 171.4 8x5/8-11 UNC 111.1
A1 - 11 279.4 196.885 19.05 34.9 11x3/4-10 UNC 235 8x3/4-10 UNC 165.1
A1 - 15 381 285.8 20.638 41.3 12x7/8-9 UNC 330.2 11x7/8-9 UNC 247.6
A1 - 20 520 412.8 22.225 47.6 12x1-8 UNC 463.6 11x1-8 UNC 368.3
Type A: Tapped holes in ange (outer bolt circle) without inner bolt circle.
A2
A2
Spindle nose size A B max C D E1 F1
A2 - 3 92.1 53.985 11.1 15.9 3x7/16-14 UNC 70.66
A2 - 4 108 63.525 11.1 19 11x7/16-14 UNC 82.55
A2 - 5 133.4 82.575 12.7 22.2 11x7/16-14 UNC 104.8
A2 - 6 165.1 106.390 14.3 25.4 11x1/2-13 UNC 133.4
A2 - 8 209.5 139.735 15.9 28.6 11x5/8-11 UNC 171.4
https://toolsmach.com/en/content/15-lathe-chucks 2/7
5/8/2020 Lathe Chucks
B1
B1
C
Spindle nose size A B max D G F1 E2 F2
-0.025
B1 - 5 133.4 82.575 14.288 22.2 11x11.9 104.8 8x7/16-14 UNC 61.9
B1 - 6 165.1 106.390 15.875 25.4 11x13.5 133.4 8x1/2-13 UNC 82.6
B1 - 8 209.5 139.735 17.462 28.6 11x16.7 171.4 8x5/8-11 UNC 111.1
B1 - 11 279.4 196.885 19.05 34.9 11x20.2 235 8x3/4-10 UNC 165.1
B1 - 15 381 285.8 20.638 41.3 12x23.4 330.2 11x7/8-9 UNC 247.6
B1 - 20 520 412.8 22.225 47.6 12x26.6 463.6 11x1-8 UNC 368.3
B2
B2
Spindle nose size A B max C D G F1
B2 - 3 92.1 53.985 11.1 15.9 3x11.9 70.66
B2 - 4 108 63.525 11.1 19 11x11.9 82.55
B2 - 5 133.4 82.575 12.7 22.2 11x11.9 104.8
B2 - 6 165.1 106.390 14.3 25.4 11x13.5 133.4
B2 - 8 209.5 139.735 15.9 28.6 11x16.7 171.4
https://toolsmach.com/en/content/15-lathe-chucks 3/7
5/8/2020 Lathe Chucks
A B g5 Cmin D E F
M 20 21 30 6.3 10 20
M 24 25 36 8 12 24
M 33 34 50 9 14 30
0 M 39 40 56 10 16 35
M 45 46 67 11 18 40
https://toolsmach.com/en/content/15-lathe-chucks 4/7
5/8/2020 Lathe Chucks
M 52 55 80 12 20 45
M 60 62 90 14 22 50
M 76x6 78 112 16 30 63
M 105x6 106 150 20 40 80
Chuck Types
Self-Centering Chucks are ideal for gripping cylindrical or concentric work because all jaws work in unison and automatically center the piece. Independent chucks are
suited for gripping irregularly shaped workpieces or for eccentric operations because jaws work independently. Adjustable chucks operate like a self-centering chuck but
are used where extreme accuracy is required. User may adjust within .0005 T.I.R.
MOUNTING INSTRUCTIONS:
LATHE MUST BE LEVELED WITH A PRECISION LEVEL
Chuck Mounting Information: Using Intermediate Plates -
For Standard Flat Back Lathe Chucks-
NOT for “Adjustable Run-Out” models (see separate instructions). When using a Chuck Adapter Plate to mount a at back lathe chuck: 1. The lathe must be levelled with a
precision level, this assures machining accuracy
2. Adapter plate or chuck plate is to be mounted on lathe spindle
3. A skim facing cut across the full face of the adaptor must be made. This assures that the face is at 90° to the centerline of the lathe spindle
4. The chuck plate has a boss onto which the recess in back of the chuck must mount. Turn the boss to t tightly into the chuck body. The accuracy of this operation is
directly relative to best results
5. Turn the O.D. of the chuck plate to match the chuck --- not always the same size of the chuck body, especially with 4 jaw independent chucks
6. In most cases the chuck has threaded holes in the chuck body, to accept mounting bolts, or the chuck plate has threaded holes, for chucks having through holes in the
body for front insertion. In some instances it may be necessary to transfer hole locations and drill clearance holes
7. “A” type adaptors come in two versions: A-1 has two bolt circles (inner & outer), A-2 has a single bolt circle (outer) of tapped holes. The chuck adaptor is fastened to
spindle separately, then the chuck is fastened to the plate
8. Lathes having threaded spindle noses follow similar procedures 1 thru 6
Chuck Mounting Information: Using Intermediate Adaptors - For ADJUSTABLE Run-Out Chucks, known as: “Adjust-Tru”, “Set-Tru”, “Zero-Set”, “Set-Rite”, “Hi-Tru”, “Accu-
Chuck”.
This type of chuck is designed so that the chuck body can be moved by utilizing adjusting screws. A ground pin is held rmly in the chuck mounted on the lathe. The pin is
trammed with a test indicator and the adjusting screws used to correct the run-out. The design of the chuck adaptor permits the chuck adjusting screws to contact an
extended boss on the plate, facilitating adjustment. Each brand chuck requires its matching adaptor - same manufacturer or speci c identi cation - they are not
interchangeable (unless so indicated). These adaptors are to be “zeroed in” prior to actually mounting the chuck by taking a skim facing cut across the ange. All other
dimensions should be compared to the back of the speci c chuck and machined accordingly, if necessary. Once the mounted chuck has been “zeroed-in” in all respects,
the chuck must be “locked” into the adjusted position. Double check with ground pin and test indicator.
Note
0 - Plain Back Chucks Require Adapter or Converter Which May Require Machining to Fit Back of Chuck
https://toolsmach.com/en/content/15-lathe-chucks 5/7
5/8/2020 Lathe Chucks
GET NEWSLETTER
FOLLOW US
Your email address SUBSCRIBE
GET IN TOUCH
+48 85 664 75 33
store@toolsmach.com
INFORMATION
Delivery
Contact
Sitemap
About us
LOCATION
0
https://toolsmach.com/en/content/15-lathe-chucks 6/7
5/8/2020 Lathe Chucks
Dane do Zgłoś
Mapybłąd w mapach
©2020 Google
0
https://toolsmach.com/en/content/15-lathe-chucks 7/7