Professional Documents
Culture Documents
MALAGA
345C/365C/385C
HYDRAULIC
EXCAVATORS
4 : 03 10
OK
MONITOR
Francis
Sep 05
Monitoring System Operation Manual
- Contents -
1. Outline of the Monitor..................................................................................... 1
1.1. Parts Name .................................................................1
1.2. Startup Process ............................................................5
1.2.1. Pre-start Monitoring Function ..........................................5
1.3. Warning Indications ........................................................6
2. Outline of Service Functions .......................................................................... 9
2.1. Password Entry ............................................................11
3. Setting.......................................................................................................... 12
3.1. Display Setup .............................................................12
3.1.1. Clock Adjust ..........................................................12
3.1.2. Select Language .......................................................13
3.1.3. Select Indication Item.................................................14
3.1.4. Adjust Contrast .......................................................15
3.1.5. Adjust Brightness .....................................................16
3.2. Work Tool Select ..........................................................17
3.3. Controls Setup(365C/385C)..................................................18
4. Maintenance Information.............................................................................. 19
5. Performance ................................................................................................ 21
6. Service ......................................................................................................... 23
6.1. Maintenance ...............................................................24
6.1.1. Reverse Fan ...........................................................24
6.1.2. Filter/Fluid Information ...............................................26
6.1.3. Recommend Interval.....................................................27
6.1.4. Work Hour Info.........................................................28
6.2. Password Change............................................................29
6.3. Diagnostic ................................................................30
6.3.1. Active Error ..........................................................30
6.3.2. Logged Error...........................................................31
6.3.3. Logged Event...........................................................33
6.4. ECM Info ..................................................................35
6.4.1. Machine ECM ...........................................................35
6.4.2. Engine ECM.............................................................36
6.4.3. Monitor................................................................37
6.4.4. Attachment ECM (345C)..................................................38
6.5. Status ....................................................................39
6.5.1. Digital Input Status ..................................................39
6.5.2. Analog Input Status....................................................42
6.5.3. Output Status..........................................................44
6.5.4. Misc Status............................................................47
6.6. Calibrations ..............................................................49
Monitoring System Operation Manual
① … Alert indicator
This lamp blinks when the serious
warning occurs. About the warning
indication, See "1.3. Warning
Indicator".
② … Display
See the next page about each
indication item.
③ … Keypad
1
Monitoring System Operation Manual
Clock
Coolant Temperature
Note: The total operation hour is counted by Machine ECM. So if you want to know accurate
operation time, see the mechanical service hour meter.
2
Monitoring System Operation Manual
Note: Gain/Response Mode is changed by pushing the gain/response switch of the standard
switch panel module. (See the following picture.)
3
Monitoring System Operation Manual
PRESS TO SET
CLOCK, LANGUAGE,
TOOL AND CONTROLS Operation Guidance
In this area, the short message which explain the function of
key is displayed.
/ :MOVE CURSOR
4
Monitoring System Operation Manual
Turn the engine start switch to the ON position. After approximately one second, CAT logo
appears in the display and the alert indicator turns on. The coolant temperature, the hydraulic
oil temperature, the fuel level, and the position of the engine speed dial are now indicated.
And the pattern for the joystick controls is indicated in the bottom of display for 3 sec
(Electronic Joystick System Only).
The monitoring system checks the level of the engine coolant, the engine oil, and the
hydraulic oil before the engine starts. If the fluid level check detects a low fluid level, the
appropriate message will be displayed and a pictograph will be shown to indicate the fluid
level that is low.
Note: If more than one fluid level is low, the right key and the left key symbols are indicated
in the bottom right area of warning message indication. Press the right key or the left key, and
check other indicated warning message. The low fluid level indicators will disappear after five
seconds when the engine is started.
Note: The machine cannot perform an accurate fluid level check when the machine is on a
slope. Perform the fluid level check on level ground.
If the engine is started during the fluid level check, the monitor will cancel these checks.
The service hours for the filters are checked and the service hours for the fluids are checked
next. If a filter or a fluid is over the recommended change interval, “CHECK FLTR/FLUID
INFO” appears on the display. Refer to “Main Menu” for further information.
5
Monitoring System Operation Manual
When some events or warning have occurred, the following message will be displayed in the
default screen.
6
Monitoring System Operation Manual
7
Monitoring System Operation Manual
8
Monitoring System Operation Manual
Menu Key:
MAIN MENU
SETTING SETTING
MAINTENANCE INFO Indicate DISPLAY SETUP Clock adjust/Language
PERFORMANCE filter/fluid WORK TOOL SELECT select/Indicated item
SERVICE information select/Contrast adjust/
Brightness adjust
SERVICE
MAINTENACE MAINTENANCE
PASSWORD CHANGE Change user REVERSE FAN Start/Stop the
DIAGNOSTIC password FLTR/FLUID INFO reverse fan
ECM INFO
RECOMMEND INTERVAL
STATUS
WORK HOUR INFO
CALIBRATIONS
OVERRIDE
DEVICE TEST
CONFIGURATIONS
TOOL PROGRAM
9
Monitoring System Operation Manual
[Entry]
Press the menu key in order to enter the service mode (Main Menu). And go to the desired
menu by using the up/down/right/left/OK key. The menu key is available in every menu. If the
menu key is pressed while doing some functions, the monitor stops doing that function and
displays the main menu.
[Exit]
Press the home key in order to return to the default screen.
When the home key is pressed, the monitor stops doing service mode functions.
The home key is available in every menu.
Note: If the home key/the menu key is pressed while doing some functions, it takes 1-2
seconds to return to the default screen/the main menu for exit process
10
Monitoring System Operation Manual
3. Setting
3.1. Display Setup
3.1.1. Clock Adjust
( MAIN MENU → SETTING → DISPLAY SETUP → CLOCK ADJUST )
12
Monitoring System Operation Manual
Go to the
DISPLAY SETUP LANGUAGE SELECT [Select language]
○ENGLISH ▲ Press the up key or the
Refer to ○FRANCAIS down key in order to scroll
“3.1.1. Clock Adjust” ○DEUTSCH through the available
○ITALIANO
↓ languages. And move
○ESPAÑOL
DISPLAY SETUP ○日本語 ▼
cursor to the desired
CLOCK ADJUST ▲ PRESS TO SELECT language. Press the set key
LANGUAGE SELECT HIGHLIGHTED ITEM in order to select the desired
INDICATED ITEM language.
CONTRAST
BRIGHTNESS :SELECTED
BRIGHTNESS( ) ▼ / :MOVE CURSOR
PRESS TO ADJUST ↓
CLOCK
[Select language]
↓
/ :MOVE CURSOR ↓
↓ Default Screen
Function
Select the highlighted
↓ item
DISPLAY SETUP
Move cursor
CLOCK ADJUST ▲
LANGUAGE SELECT Move cursor
INDICATED ITEM
CONTRAST
BRIGHTNESS
BRIGHTNESS( ) ▼
PRESS TO SELECT
DISPLAY LANGUAGE
/ :MOVE CURSOR
↓
13
Monitoring System Operation Manual
14
Monitoring System Operation Manual
Go to the
DISPLAY SETUP CONTRAST [Adjust contrast]
The contrast can be set
Refer to between “0” and “10”. Press
“3.1.1.Clock Adjust” the right key in order to
↓ increase the contrast. Press
DISPLAY SETUP 5
the left key in order to
CLOCK ADJUST ▲ decrease the contrast.
LANGUAGE SELECT
INDICATED ITEM
CONTRAST
BRIGHTNESS
BRIGHTNESS( ) ▼ / :-/+
PRESS TO ADJUST ↓ Function
CLOCK Increase the number
[Contrast adjust]
Decrease the number
↓
/ :MOVE CURSOR ↓
↓ Default Screen
↓
DISPLAY SETUP
CLOCK ADJUST ▲
LANGUAGE SELECT
INDICATED ITEM
CONTRAST
BRIGHTNESS
BRIGHTNESS( ) ▼
PRESS TO SET
CONTRAST
/ :MOVE CURSOR
↓
15
Monitoring System Operation Manual
Go to the
DISPLAY SETUP BRIGHTNESS [Adjust brightness]
The brightness can be set
Refer to between “0” and “10”. Press
“3.1.1.Clock Adjust” the right key in order to
↓ increase the brightness.
DISPLAY SETUP 5
Press the left key in order to
CLOCK ADJUST ▲ decrease the brightness.
LANGUAGE SELECT
INDICATED ITEM
CONTRAST Function
BRIGHTNESS
BRIGHTNESS( )
Increase the number
▼ / :-/+
PRESS TO ADJUST Decrease the number
↓
CLOCK
[Adjust brightness]
↓
/ :MOVE CURSOR
↓
↓
Default Screen
↓
DISPLAY SETUP
CLOCK ADJUST ▲
LANGUAGE SELECT
INDICATED ITEM
CONTRAST
BRIGHTNESS
BRIGHTNESS( ) ▼
PRESS TO SET
BRIGHTNESS
/ :MOVE CURSOR
↓
16
Monitoring System Operation Manual
17
Monitoring System Operation Manual
/ :MOVE CURSOR
↓
18
Monitoring System Operation Manual
4. Maintenance Information
( MAIN MENU → MAINTENANCE INFO )
XXXX:
The accumulated hours
PRESS TO SET
CLOCK, LANGUAGE,
TOOL AND CONTROLS
YYYY:
/ :SCROLL The recommended
↓ intervals
/ :MOVE CURSOR [Maintenance
↓ Information]
↓ Function
↓ Scroll
MAIN MENU ↓ Scroll
Default Screen
MAINTENANCE INFO Note: The indication item
varies by the model. And
the item which is checked at
the next table may not be
PRESS TO CHECK
indicated by the machine
FLUID/FLTR/COMPO configuration.
MAINTENANCE HOUR
/ :MOVE CURSOR
↓
19
Monitoring System Operation Manual
365C, 385C
345C
Display Detail
COOLANT x x Accumulated hour of coolant
HYD OIL x x Accumulated hour of hydraulic oil
ENGINE OIL x x Accumulated hour of engine oil
SWING DRIVE OIL x x Accumulated hour of swing drive oil
FINAL DRIVE OIL x x Accumulated hour of final drive oil
WATER SEPARATOR x x Accumulated hour of water separator
ENGINE OIL FILTER x x Accumulated hour of engine oil filter
FUEL FILTER x x Accumulated hour of fuel filter
PILOT OIL FILTER x x Accumulated hour of pilot oil filter
DRAIN OIL FILTER x x Accumulated hour of drain oil filter
HYD OIL RET FILTER x x Accumulated hour of hydraulic oil return filter
ATT FILTER x x Accumulated hour of attachment hydraulic oil filter
ENGINE x x Accumulated hour of engine
PUMP x x Accumulated hour of pump
TRAVEL MOTOR x x Accumulated hour of travel motor
SWING MOTOR x - Accumulated hour of swing motor
TOOL #01 x x Accumulated hour of tool#1
TOOL #02 x x Accumulated hour of tool#2
TOOL #03 x x Accumulated hour of tool#3
TOOL #04 x x Accumulated hour of tool#4
TOOL #05 - x Accumulated hour of tool#5
20
Monitoring System Operation Manual
5. Performance
( MAIN MENU → PERFORMANCE )
PERFORMANCE [Performance]
↓
BATTERY VOLTAGE ▲ A list of system components
------[V] and measurements will be
MAIN MENU ENGINE SPEED displayed. Press the up key
------[RPM]
SETTING or the down key in order to
COOLANT TEMP
------[℃] ▼
scroll through the list.
PRESS TO SET
CLOCK, LANGUAGE,
TOOL AND CONTROLS / :SCROLL Function
↓ Scroll
[Performance] Scroll
/ :MOVE CURSOR
↓ ↓
Note: The indication item
varies by the model. And
↓ ↓
the item which is checked at
MAIN MENU Default Screen the next table may not be
indicated by the machine
PERFORMANCE
configuration.
PRESS TO SEE
PERFORMANCE
/ :MOVE CURSOR
↓
21
Monitoring System Operation Manual
365C, 385C
345C
Display Detail
BATTERY VOLTAGE x x Battery Voltage
ENGINE SPEED x x Engine Speed
COOLANT TEMP x x Coolant Temperature
HYD OIL TEMP x x Hydraulic Oil Temperature
PUMP #1 PRES - x Pump #1 Pressure
PUMP #2 PRES - x Pump #2 Pressure
MAIN PUMP PRES x - Main Pump Pressure
SWING PUMP PRES x - Swing Pump Pressure
POWER SHIFT PRES x x Power Shift Pressure
FLOW LIMIT PRES - x Flow Limit Pressure
FLOW LIMIT - x Flow Limitation
22
Monitoring System Operation Manual
23
Monitoring System Operation Manual
▼
PRESS TO START
REVERSE FAN
/ :MOVE CURSOR
↓
24
Monitoring System Operation Manual
:BACK :BACK
[ACTIVE]
REVERSE FAN
ACTIVE
PRESS TO CANCEL
REVERSE FAN MODE
:BACK
[ABORT]
REVERSE FAN
ABORT
:BACK
25
Monitoring System Operation Manual
Go to the
FLTR/FLUID INFO [Reset Accumulated Hour]
MAINTENACE
ENGINE OIL FILTER ▲ Press the up key or down
XXXX/YYYY[HR] key in order to highlite
HYD OIL RET FILTER desired item.
Refer to
XXXX/YYYY[HR]
“6.1.1.Reverse Fan”
PILOT OIL FILTER
↓ XXXX/YYYY[HR] ▼ Press the OK key in order to
MAINTENANCE PRESS TO CHANGE move cursor to accumulated
REVERSE FAN ▲ DATA hour position.
FLTR/FLUID INFO
RECOMMEND INTERVAL FLTR/FLUID INFO
WORK HOUR INFO ENGINE OIL FILTER ▲
/ :MOVE CURSOR XXXX/YYYY[HR]
▼ ↓ HYD OIL RET FILTER
PRESS TO START [Reset Accumulated Hour] XXXX/YYYY[HR]
REVERSE FAN PILOT OIL FILTER
↓
XXXX/YYYY[HR] ▼
PRESS TO SET
↓ CHANGED DATA
/ :MOVE CURSOR Default Screen
↓
:CANCEL
:RESET HOUR
↓
MAINTENANCE
REVERSE FAN ▲
FLTR/FLUID INFO
Press the left key in order to
RECOMMEND INTERVAL reset the accumulated hour.
WORK HOUR INFO
Then, press the OK key in
▼ order to set the reseted hour.
PRESS TO RESET
FLTR/FLUID INFO If you press the back key
before the OK key, then the
reset hour is not stored.
/ :MOVE CURSOR
↓
26
Monitoring System Operation Manual
Go to the
RECOMMEND INTERVAL [Change Recommended
MAINTENACE
ENGINE OIL FILTER ▲ Interval]
XXXX/YYYY[HR] Press the up key or down
HYD OIL RET FILTER key in order to highlite
Refer to
XXXX/YYYY[HR]
“6.1.1.Reverse Fan” desired item.
PILOT OIL FILTER
↓ XXXX/YYYY[HR] ▼
MAINTENANCE PRESS TO CHANGE Press the OK key in order to
REVERSE FAN ▲ DATA move cursor to the
FLTR/FLUID INFO recommended interval
RECOMMEND INTERVAL position.
WORK HOUR INFO
/ :MOVE CURSOR RECOMMEND INTERVAL
▼ ↓ ENGINE OIL FILTER ▲
PRESS TO START [Change Recommended XXXX/YYYY[HR]
REVERSE FAN Interval] HYD OIL RET FILTER
XXXX/YYYY[HR]
↓
PILOT OIL FILTER
XXXX/YYYY[HR] ▼
/ :MOVE CURSOR ↓ PRESS TO SET
↓ Default Screen CHANGED DATA
↓ :CANCEL
MAINTENANCE / :+/-
REVERSE FAN ▲
FLTR/FLUID INFO
RECOMMEND INTERVAL Press the up key or the
WORK HOUR INFO down key in order to
increase or decrease the
▼ recommended intervals.
PRESS TO CHANGE
RECOMMEND INTERVAL Press the OK key in order to
store the changed values.
27
Monitoring System Operation Manual
Go to the
WORK HOUR INFO [Reset Work Hour]
MAINTENACE
ENGINE ▲ Press the up key or down
XXXX[HR] key in order to highlite
PUMP desired item.
Refer to
XXXX[HR]
“6.1.1.Reverse Fan”
TRAVEL MOTOR
↓ XXXX[HR] ▼ Press the OK key in order to
MAINTENANCE PRESS TO CHANGE move cursor to work hour
REVERSE FAN ▲ DATA position.
FLTR/FLUID INFO
RECOMMEND INTERVAL WORK HOUR INFO
WORK HOUR INFO ENGINE ▲
/ :MOVE CURSOR XXXX[HR]
▼ ↓ PUMP
PRESS TO START [Reset Work Hour] XXXX[HR]
REVERSE FAN TRAVEL MOTOR
↓
XXXX[HR] ▼
PRESS TO SET
↓ CHANGED DATA
/ :MOVE CURSOR Default Screen
↓
:CANCEL
:RESET HOUR
↓
MAINTENANCE
Press the left key in order to
REVERSE FAN ▲
FLTR/FLUID INFO
reset the accumulated hour.
RECOMMEND INTERVAL
WORK HOUR INFO Then, press the OK key in
order to set the reseted hour.
▼
PRESS TO RESET If you press the back key
WORK HOUR INFO before the OK key, then the
reset hour is not stored.
/ :MOVE CURSOR
↓
28
Monitoring System Operation Manual
Go to the
PASSWORD [Enter New Password]
SERVICE
ENTER NEW PASSWORD Press the right key or the
left key in order to highlight
_ _ _ _ desired letter.
Refer to
“6.Service”
CDEF01234
↓ Press the OK key in order to
SERVICE PRESS TO ENTER set a highlighted letter.
MAINTENANCE ▲ HIGHLIGHTED LETTER
PASSWORD CHANGE Press the back key in order
DIAGNOSTIC to delete a selected letter.
ECM INFO :DELETE
STATUS / :MOVE CURSOR When you enter 4 letters,
CALIBRATIONS ▼ ↓ then the confirmation screen
PRESS TO CHANGE [Enter New Password] is displayed.
MAINTE INFO ↓
[Confirmation Screen]
PASSWORD
↓
ENTER NEW PASSWORD
/ :MOVE CURSOR Default Screen
↓ * * * *
29
Monitoring System Operation Manual
Go to the
DIAGNOSTIC [Active Error List]
SERVICE
ACTIVE ERROR ▲ Active error is displayed as
LOGGED ERROR the following format.
LOGGED EVENT
Refer to
“6.Service” MID : CID – FMI
↓ ▼
PRESS TO CHECK MID:
SERVICE
MAINTENANCE ▲ ACTIVE ERROR INFO Control Module ID which
PASSWORD CHANGE detected error component
DIAGNOSTIC
ECM INFO CID:
STATUS / :MOVE CURSOR Component ID estimated
CALIBRATIONS ▼ ↓ with error status
PRESS TO CHANGE
[Active Error List]
MAINTE INFO FMI:
↓
Failure Mode ID
↓
Refer to the appendix about
/ :MOVE CURSOR Default Screen
↓ MID, CID, FMI code.
/ :SCROLL
/ :MOVE CURSOR
↓
30
Monitoring System Operation Manual
31
Monitoring System Operation Manual
[Delete Log]
When you press the OK key
in the detail screen, then the
delete confirmation screen
is displayed.
[Confirmation Screen]
LOGGED ERROR
▲
DELETE THIS DATA ?
MMM : CCCC – FF
YES / NO ▼
:ENTER
/ :MOVE CURSOR
32
Monitoring System Operation Manual
[Delete Log]
When you press the OK key
in the detail screen, then the
delete confirmation screen
is displayed.
[Confirmation Screen]
LOGGED EVENT
▲
DELETE THIS DATA ?
MMM :EEEEEE-LL
YES / NO ▼
:ENTER
/ :MOVE CURSOR
34
Monitoring System Operation Manual
Go to the
ECM INFO [ECM Information]
SERVICE
MACHINE ECM ▲ Press the up key or the
ENGINE ECM down key in order to see the
MONITOR following ECM information.
Refer to
ATT ECM
“6.Service”
↓ ▼
• Product ID
SERVICE PRESS TO SELECT • ECM Part Number
MAINTENANCE ▲ ECM • ECM Serial Number
PASSWORD CHANGE • Software Group Number
DIAGNOSTIC • Software Group
ECM INFO Release Date
STATUS / :MOVE CURSOR
CALIBRATIONS ▼ ↓
PRESS TO CHANGE
MAINTE INFO
↓
MACHINE ECM
PRODUCT ID ▲
/ :MOVE CURSOR XXXXXXXX
↓ ECM PART NO
XXXXXXX-XX
ECM SERIAL NO
↓ XXXXXXXX ▼
SERVICE
MAINTENANCE ▲
PASSWORD CHANGE
DIAGNOSTIC
ECM INFO
STATUS / :SCROLL
CALIBRATIONS ▼ ↓
PRESS TO SEE
[ECM Information]
ECM INFORMATION
↓
↓
/ :MOVE CURSOR Default Screen
↓
35
Monitoring System Operation Manual
Go to the
ECM INFO ENGINE ECM [ECM Information]
EQUIPMENT ID ▲ Press the up key or the
Refer to XXXXXXXX down key in order to see the
“6.4.1.Machine ECM” ENGINE SERIAL NO following ECM information.
XXXXXXXX
↓ ECM SERIAL NO
XXXXXXXX ▼ • Equipment ID
ECM INFO
MACHINE ECM ▲
• Engine Serial Number
ENGINE ECM • ECM Serial Number
MONITOR • Module Part Number
ATT ECM
▼ / :SCROLL
PRESS TO SELECT ↓
ECM [ECM Information]
↓
/ :MOVE CURSOR ↓
↓ Default Screen
↓
ECM INFO
MACHINE ECM ▲
ENGINE ECM
MONITOR
ATT ECM
▼
PRESS TO SELECT
ECM
/ :MOVE CURSOR
↓
36
Monitoring System Operation Manual
Go to the
MONITOR [ECM Information]
ECM INFO
ECM PART NO ▲ Press the up key or the
XXXXXXX-XX down key in order to see the
ECM SERIAL NO following ECM information.
Refer to XXXXXXXX
“6.4.1.Machine ECM” SOFTWARE PART NO
XXXXXXX-XX ▼ • ECM Part Number
↓
• ECM Serial Number
ECM INFO
MACHINE ECM ▲
• Software Part Number
ENGINE ECM
MONITOR
ATT ECM
/ :SCROLL
▼ ↓
PRESS TO SELECT [ECM Information]
ECM ↓
↓
/ :MOVE CURSOR Default Screen
↓
↓
ECM INFO
MACHINE ECM ▲
ENGINE ECM
MONITOR
ATT ECM
▼
PRESS TO SELECT
ECM
/ :MOVE CURSOR
↓
37
Monitoring System Operation Manual
Go to the
ATT ECM [ECM Information]
ECM INFO
ECM PART NO ▲ Press the up key or the
XXXXXXX-XX down key in order to see the
ECM SERIAL NO following ECM information.
Refer to XXXXXXXX
“6.4.1.Machine ECM” SOFTWARE PART NO
XXXXXXX-XX ▼ • ECM Part Number
↓
• ECM Serial Number
ECM INFO
MACHINE ECM ▲
• Software Group Number
ENGINE ECM • Software Group
MONITOR Release Date
ATT ECM
/ :SCROLL
▼ ↓
PRESS TO SELECT [ECM Information]
ECM ↓
↓
/ :MOVE CURSOR Default Screen
↓
↓
ECM INFO
MACHINE ECM ▲
ENGINE ECM
MONITOR
ATT ECM
▼
PRESS TO SELECT
ECM
/ :MOVE CURSOR
↓
38
Monitoring System Operation Manual
Go to the
STATUS [Status Information List]
SERVICE
DIGITAL IN STATUS ▲ Press the OK key in order to
ANALOG IN STATUS check status information.l
OUTPUT STATUS
Refer to
MISC STATUS
“6.Service” Note: The indication item
↓ ▼
varies by the model. And
SERVICE PRESS TO SEE the item which is checked at
MAINTENANCE ▲ DIGITAL INPUTS the next table may not be
PASSWORD CHANGE STATUS INFORMATION indicated by the machine
DIAGNOSTIC configuration.
ECM INFO .
STATUS / :MOVE CURSOR
CALIBRATIONS ▼ ↓
PRESS TO CHANGE
MAINTE INFO
↓
DIGITAL IN STATUS
AIR FLTR PLGD SW ▲
/ :MOVE CURSOR OK
↓ CAPSL FLTR PLGD SW
PLUGGED
BACKUP SW
↓ OFF ▼
SERVICE
MAINTENANCE ▲
PASSWORD CHANGE
DIAGNOSTIC
ECM INFO
STATUS / :SCROLL
CALIBRATIONS ▼ ↓
PRESS TO SEE
[Status Information List]
STATUS INFORMATION
↓
↓
/ :MOVE CURSOR Default Screen
↓
39
Monitoring System Operation Manual
365C/385C
345C
Display Description
AIR FLTR PLGD SW x x Air Filter Restriction Status
CAPSULE FLTR PLGD SW x x Return Hydraulic Oil Filter Status
ATT FLTR PLGD SW x x Attachment Hydraulic Oil Filter Switch Status
WATER SEP LVL SW x x Fuel/Water Separator Level Status
FUEL FLTR PLGD SW x x Engine Fuel Filter Status
2ND FUEL FLTR PLGD SW x x Secondary Fuel Filter Status
OLW ENABLE SW x x Machine Overload Warning Enable Switch Status
FINE SWING SW - x Fine Swing Switch Position
QUICK COUPLER SW - x Quick Coupler Switch Status
BACKUP SW - x Backup Mode Status
TRAVEL MODE SW x x Travel Mode Switch Status
AEC MODE SW x x AESC Resolver Switch Status
ALARM CANCEL SW x x Operator Travel Alarm Switch
TOOL SELECT SW - x Tool Select Switch Status
GAIN/RES SELECT SW x - Gain/Response Select Switch Status
LIFT/CRANE MODE SW x x Heavy lift switch status
AUTO LUB LOW LVL SW x - Auto Lube Grease Level
ONE TOUCH LOW IDLE SW x x Low Idle Switch Position
MANUAL LUB SW x - Reel Lube Switch Position
LEFT JOYSTICK SW #1 x x Left Joystick Switch #1 Status
RIGHT JOYSTICK SW #1 x x Right Joystick Switch #1 Status
LEFT JOYSTICK SW #2 x x Left Joystick Switch #2 Status
RIGHT JOYSTICK SW #2 x x Right Joystick Switch #2 Status
ATCH PUMP PRES SW x - Attachment Pump Pressure Switch Status
JOYSTK SW #2 x - Joystick Switch #2 Status
JOYSTK SW #3 x - Joystick Switch #3 Status
FLCN PRXI SW #1 x - Flow Control Proximity Switch #1 Status
FLCN PRXI SW #2 x - Flow Control Proximity Switch #2 Status
MAGNET STANDBY SW x - Magnet Circuit Standby Switch Status
UHD SW x - High Power Auxiliary Circuit Enable Switch Status
TILT CAB SW x - Low Power Auxiliary Circuit Enable Switch Status
SMART BOOM SW x - Smart Boom Switch Status
HYD LOCK SW x x Hydraulic Lock Switch Status
40
Monitoring System Operation Manual
365C/385C
345C
Display Description
CNTR WEIGHT SW x x Counterweight Removal Switch Status
JOYSTICK PRES SW - x Swing/Implement Pressure Status
TRAVEL PRES SW - x Travel Pressure Switch Status
IMPLEMENT PRES - x Implement pressure switch status
ATCH VALVE #1 SW - x Attachment Input #1 Switch Status
ATCH VALVE #3 SW - x Attachment Input #3 Switch Status
ATCH #1 TOOL SW - x Attachment #1 Tool Switch Status
ATCH #2 TOOL SW - x Attachment #2 Tool Switch Status
ATCH #3 TOOL SW - x Attachment #3 Tool Switch Status
ATCH #4 TOOL SW - x Attachment #4 Tool Switch Status
HYD OIL LVL SW x x Hydraulic Oil Level Status
COOLANT LVL SW x x Engine Coolant Level Status
ENGINE OIL LVL SW x x Engine Oil Level Status
ENGINE OIL PRESS SW x x Engine Oil Pressure Status
START AID SW x - Ether Injection Switch Position
USER SHUTDOWN SW x x User Defined Shutdown Status
41
Monitoring System Operation Manual
ANALOG IN STATUS
Go to the
BATTERY VOLTAGE ▲
STATUS 27.8[V]
ENGINE SPEED
Refer to
1980[RPM]
“6.5.1.Dital Input Status”
THROTTLE POSITION
↓ 10 ▼
STATUS
DIGITAL IN STATUS ▲
ANALOG IN STATUS
OUTPUT STATUS
MISC STATUS
/ :SCROLL
▼ ↓
PRESS TO SEE [Status Information List]
DIGITAL INPUTS ↓
STATUS INFORMATION
↓
/ :MOVE CURSOR Default Screen
↓
↓
STATUS [Status Information List]
DIGITAL IN STATUS ▲ Press the OK key in order to
ANALOG IN STATUS check status information.l
OUTPUT STATUS
MISC STATUS Note: The indication item
varies by the model. And
▼
the item which is checked at
PRESS TO SEE
the next table may not be
ANALOG INPUTS
STATUS INFORMATION indicated by the machine
configuration.
/ :MOVE CURSOR
↓
42
Monitoring System Operation Manual
365C/385C
345C
Display Description
BATTERY VOLTAGE x x Battery Voltage
ENGINE SPEED x x Actual Engine Speed
THROTTLE POSITON x x Throttle Dial Switch Position
FUEL LEVEL SENSOR x x Fuel Level Percent
COOLANT TEMP x x Engine Coolant Temperature
HYD OIL TEMP x x Hydraulic Oil Temperature
PUMP #1 PRES x Hydraulic Pump #1 Outlet Pressure
PUMP #2 PRES x Hydraulic Pump #2 Outlet Pressure
MAIN PUMP PRES x Variable Implement Pump Oil Pressure
SWING PUMP PRES x Swing Pump Outlet Pressure
OVERLOAD WARN PRES x x Machine Overload Warning Pressure
LEVER BOOM x Boom Lever Position
LEVER BUCKET x Bucket Lever Position
LEVER STICK x Stick Lever Position
LEVER SWING x Swing Lever Position
TRV LEFT PEDAL x Left Travel Position
TRV RIGHT PEDAL x Right Travel Position
LEFT THUMBWHEEL x x Left Joystick Thumbwheel Position
RIGHT THUMBWHEEL x x Right Joystick Thumbwheel Position
JOYSTK SW #1(PROP) x Joystick Switch #1 Status
JOYSTK SW #4(PROP) x Joystick Switch #4 Status
ATCH LEFT PEDAL x Left Attachment Pedal Position
ATCH RIGHT PEDAL x Right Attachment Pedal Positio
ATCH PEDAL x Attachment Pedal Position
ATMOSPHELIC PRES x x Atmospheric Pressure
AUTO LUB PRESS x Auto Lube Pressure
INTAKE AIR TEMP x x Intake Manifold Air Temperature
FUEL TEMP x x Fuel Temperature
FUEL PRES x x Fuel Pressure
FUEL PRES (ABS) x x Fuel Pressure (absolute)
ENG OIL PRES x x Engine Oil Pressure
ENG OIL PRES (ABS) x x Engine Oil Pressure (absolute)
TURBO OUT PRES (ABS) x x Turbo Outlet Pressure (absolute)
BOOST PRES x x Boost Pressure
STRAIGHT TRV PEDAL x Straight Travel Position
43
Monitoring System Operation Manual
OUTPUT STATUS
Go to the
TRAVEL SPEED SHIFT ▲
STATUS OFF
SWING BREAK SOL
Refer to
OFF
“6.5.1.Dital Input Status”
LIFT MODE SOL
↓ OFF ▼
STATUS
DIGITAL IN STATUS ▲
ANALOG IN STATUS
OUTPUT STATUS
MISC STATUS
/ :SCROLL
▼ ↓
PRESS TO SEE [Status Information List]
DIGITAL INPUTS ↓
STATUS INFORMATION
↓
/ :MOVE CURSOR Default Screen
↓
↓
STATUS [Status Information List]
DIGITAL IN STATUS ▲ Press the OK key in order to
ANALOG IN STATUS check status information.l
OUTPUT STATUS
MISC STATUS
Note: The indication item
▼
varies by the model. And
PRESS TO SEE the item which is checked at
OUTPUT the next table may not be
STATUS INFORMATION indicated by the machine
configuration.
/ :MOVE CURSOR
↓
44
Monitoring System Operation Manual
365C/385C
345C
Display Description
HYD LOCK SOL x - Hydraulic Lock Solenoid Status
TRV SPEED SHIFT x x Travel Speed Solenoid
SWING BREAK SOL x x Swing Brake Solenoid Status
TRV ALARM x x Travel Alarm Control Status
SYSTEM PRES UP x - Front System High Pressure Solenoid Status
NUTRAL FLOW BYPASS x - Neutral Flow Bypass Solenoid Status
ANTI DRIFT BOOM x - Boom Anti Drift Solenoid Status
ANTI DRIFT STICK x - Stick Anti Drift Solenoid Status
AUTO LUB RELAY x - Auto Lube Solenoid Status
COOLING FAN CURRENT x - Fan Speed Solenoid Current Status
REVERSE FAN SOL x x Reverse Fan Solenoid Status
LIFT MODE SOL - x Heavy Lift Control Status
1P/2P CHANGE SOL - x Auxiliary Circuit Flow Combining Solenoid Status
FAULT ALARM x x Action Alarm Status
DESIRED ENG SPEED x x Desired Engine RPM
BOOM EXTEND x - Boom Cylinder Rod Extend Solenoid Current
BOOM RETRACT x - Boom Cylinder Rod Retract Solenoid Current
STICK EXTEND x - Stick cylinder Rod Extend Solenoid Current
STICK RETRACT x - Stick cylinder Rod Retract Solenoid Current
BUCKET EXTEND x - Bucket cylinder Rod Extend Solenoid Current
BUCKET RETRACT x - Bucket cylinder Rod Retract Solenoid Current
SWING LEFT x - Swing Left Solenoid Current
SWING RIGHT x - Swing Right Solenoid Current
TRAVEL LEFT FW x - Left Travel Forward Solenoid Current Status
TRAVEL LEFT BW x - Left Travel Backward Solenoid Current Status
TRAVEL RIGHT FW x - Right Travel Forward Solenoid Current Status
TRAVEL RIGHT BW x - Right Travel Backward Solenoid Current Status
BM LOWERING CHECK x - Boom Lowering Check Valve Solenoid Current Status
ST LOWERING CHECK x - Stick Lowering Check Valve Solenoid Current Status
ATCH EXTEND x - Attachment Extend/CW Solenoid Current Status
ATCH RETRACT x - Attachment Retract/CCW Solenoid Current Status
MID CIRCUIT #1-A x - Medium Pressure Circuit #1-A Solenoid Current Status
MID CIRCUIT #1-B x - Medium Pressure Circuit #1-B Solenoid Current Status
POWER SHIFT PRES x - Implement Pump Power Shift Pressure Solenoid Current Status
POWER SHIFT PRES - x Power Shift Pressure
DESIRED PS PRESS x - Desired Implement Pump Power Shift Pressure
45
Monitoring System Operation Manual
365C/385C
345C
Display Description
FLOW LIMIT PRES - x Main Pump Flow Limitation Pressure
FLOW LIMIT - x Main Pump Flow Limit
SWING PUMP SWASH x - Swing Pump Swash Plate Angle Solenoid Current Status
FAN MOTOR SPEED - x Desired Engine Cooling Fan Speed
ATCH #1 EXTEND VALVE - x Attachment Valve #1 Extend Pressure Command
ATCH #1 RETRACT VALVE - x Attachment Valve #1 Retract Pressure Command
ATCH #3 EXTEND VALVE - x Attachment Valve #3 Extend Pressure Command
ATCH #3 RETRACT VALVE - x Attachment Valve #3 Retract Pressure Command
RELIEF CHK SOL #1 - x Relief Valve Check Solenoid #1
RELIEF CHK SOL #2 - x Relief Valve Check Solenoid #2
ATCH #1 RELEAF VALVE - x Variable Relief Valve #1 Pressure Command
ATCH #2 RELEAF VALVE - x Variable Relief Valve #2 Pressure Command
46
Monitoring System Operation Manual
MISC STATUS
Go to the
ALTERNATOR R TERM ▲
STATUS OK
FUEL CONSUMPTION
Refer to
10.5[L/h]
“6.5.1.Dital Input Status”
ENG POWER DERATE
↓ ON ▼
STATUS
DIGITAL IN STATUS ▲
ANALOG IN STATUS
OUTPUT STATUS
MISC STATUS
/ :SCROLL
▼ ↓
PRESS TO SEE [Status Information List]
DIGITAL INPUTS ↓
STATUS INFORMATION
↓
/ :MOVE CURSOR Default Screen
↓
↓
STATUS [Status Information List]
DIGITAL IN STATUS ▲ Press the OK key in order to
ANALOG IN STATUS check status information.l
OUTPUT STATUS
MISC STATUS
Note: The indication item
▼
varies by the model. And
PRESS TO SEE the item which is checked at
MISC the next table may not be
STATUS INFORMATION indicated by the machine
configuration.
/ :MOVE CURSOR
↓
47
Monitoring System Operation Manual
365C/385C
345C
Display Description
ALTERNATOR R TERM x x Alternator Status
DES ENG FAN SP x Desired Engine Cooling Fan Speed
UHD FLOW RATE x High Power Auxiliary Circuit Flow Rate
SPOOL GAIN SEL x Spool Gain Selection
SPOOL RES SEL x Spool Response Selection
AEC MODE STAT x Automatic Engine Control Mode
WORK MODE x Machine Work Mode
TRAVEL MODE x Travel Speed Shift Setting
AUTO LUB MODE x Machine Auto Lube Control Mode
ENGINE DIAG CLOCK x Engine ECM Diagnostic Clock
ONE TOUCH IDOL ST x One Touch Low Idle Feature Status
START AID STATUS x Ether Injection
TOTAL FUEL x Total Fuel
FUEL CONSUMPTION x x Fuel Consumption Rate
RATED FUEL LIMIT x Torque Rack Limit
FRC FUEL LIMIT x Effective Smoke Rack Limit
ENG LOAD FACTOR x Percent Engine Load at Current Engine Speed
ENG POWER DERATE x x Engine Power Derate Percentage
48
Monitoring System Operation Manual
Go to the
CALIBRATIONS [Calibration]
SERVICE
CONTROL VALVES ▲ In the calibration screen,
RELIEF VALVES step number is displayed in
PS PRES VALVE blue.
Refer to
FLOW LIMIT VALVE
“6.Service”
CHECK VALVES
↓ LEVER/PEDAL/ATCH ▼
Perform the operation
PRESS TO PERFORM written in the following table
SERVICE
MAINTENANCE ▲ CALIBRATION in each step.
PASSWORD CHANGE
DIAGNOSTIC [Calibration Screen]
ECM INFO CALIBRATION TITLE
STATUS / :MOVE CURSOR
CALIBRATIONS ▼ ↓ STEP No: STEP NAME
PRESS TO CHANGE
MAINTE INFO
↓ S E
CONTROL VALVES
ALL VALVE ▲ OPERATION GUIDANCE
BOOM VALVE
/ :MOVE CURSOR
STICK VALVE
↓ BUCKET VALVE
RIGHT TRV VALVE
↓ LEFT TRV VALVE ▼ / :SCROLL
SERVICE PRESS TO PERFORM
PASSWORD CHANGE CALIBRATION
▲ S: Start step number
DIAGNOSTIC
E: End step number
ECM INFO
STATUS
CALIBRATIONS / :MOVE CURSOR
DEVICE TEST ▼ ↓
PRESS TO PERFORM
CALIBRATION
↓
[Calibration]
↓
/ :MOVE CURSOR
↓ ↓
Default Screen
↓
49
Monitoring System Operation Manual
Step Operation
01 Press the OK key in
order to go the next.
02 Raise boom and stick
to the max position.
Then press the OK
key.
03 Set the hydraulic oil
lever to unlock
position.
04 Press the OK key in
order to go the next.
05 Hold left lever back.
06 Hold left lever back.
07 Press the OK key in
order to go the next.
08 Hold left lever back.
09 Hold left lever back.
10 Hold left lever back.
11 Hold left lever back.
12 Release all levers
and pedals.
13 Press the OK key in
order to go the next.
14 End of calibration.
50
Monitoring System Operation Manual
↓
[Calibration]
51
Monitoring System Operation Manual
↓
[Calibration]
52
Monitoring System Operation Manual
↓
[Calibration]
53
Monitoring System Operation Manual
↓
[Calibration]
54
Monitoring System Operation Manual
↓
[Calibration]
55
Monitoring System Operation Manual
↓
[Calibration]
56
Monitoring System Operation Manual
↓
[Calibration]
57
Monitoring System Operation Manual
↓
[Calibration]
58
Monitoring System Operation Manual
↓
[Calibration]
59
Monitoring System Operation Manual
↓
[Calibration]
60
Monitoring System Operation Manual
Go to the
RELIEF VALVES [Calibration]
CALIBRATIONS
ATCH #1 RLF VALVE ▲ In the calibration screen,
ATCH #2 RLF VALVE step number is displayed in
Refer to blue.
“6.6.1.1.All Valves”
↓ ▼
Perform the operation
CALIBRATIONS PRESS TO PERFORM written in the following table
CONTROL VALVES ▲ CALIBRATION in each step.
RELIEF VALVES
PS PRES VALVE Step Operation
FLOW LIMIT VALVE 01 Connect the pressure
/ :MOVE CURSOR
CHECK VALVES gauge.
LEVER/PEDAL/ATCH ▼ ↓ Then press the OK
PRESS TO PERFORM
key in order to go the
CALIBRATION
↓ next.
[Calibration] 02 Hold the tool controls
↓ to operating position
/ :MOVE CURSOR during calibration.
↓ ↓ Press the OK key.
Default Screen 03 Press the right key or
↓ the left key in order to
CALIBRATIONS
increase or decrease
CONTROL VALVES the current value.
▲
[Calibration Screen] And tune the
RELIEF VALVES CALIBRATION TITLE
PS PRES VALVE pressure to the
FLOW LIMIT VALVE STEP No: STEP NAME target.
CHECK VALVES When you finish
LEVER/PEDAL/ATCH ▼ tuning, press the OK
PRESS TO PERFORM L U key.
CALIBRATION C 04 Same as step 02.
OPERATION GUIDANCE 05 Same as step 03.
06 Release all controls.
/ :MOVE CURSOR Then press the OK
↓ key.
/ :SCROLL 07 End of calibration
↓
L: Lower limit Note: The step of the upper
U: Upper limit table may be omitted
C: Current value corresponding to the
condition.
61
Monitoring System Operation Manual
↓
[Calibration]
62
Monitoring System Operation Manual
L: Lower limit
/ :MOVE CURSOR U: Upper limit
↓ C: Current value
↓
[Calibration]
63
Monitoring System Operation Manual
Go to the
FLOW LIMIT VALVE [Calibration]
CALIBRATIONS
FLOW LIMIT PRES ▲ In the calibration screen,
2PUMP FLOW LIMIT step number is displayed in
1PUMP FLOW LIMIT blue.
Refer to
“6.6.1.1.All Valves” Perform the operation
↓ ▼
written in the following table
CALIBRATIONS PRESS TO PERFORM in each step.
CONTROL VALVES ▲ CALIBRATION
RELIEF VALVES Step Operation
PS PRES VALVE 01 Connect the pressure
FLOW LIMIT VALVE gauge.
/ :MOVE CURSOR
CHECK VALVES Then press the OK
LEVER/PEDAL/ATCH ▼ ↓ key in order to go the
PRESS TO PERFORM
next.
CALIBRATION
↓ 02 Move stick to the
[Calibration] relief position.
↓ Press the OK key.
/ :MOVE CURSOR 03 Hold the stick
↓ ↓ controls to relief
Default Screen position during
↓ calibration.
CALIBRATIONS
Press the OK key.
CONTROL VALVES 04 Press the right key or
▲
[Calibration Screen] the left key in order to
RELIEF VALVES CALIBRATION TITLE
PS PRES VALVE increase or decrease
FLOW LIMIT VALVE STEP No: STEP NAME the current value.
CHECK VALVES And tune the
LEVER/PEDAL/ATCH ▼ pressure to the
PRESS TO PERFORM L U target.
CALIBRATION C When you finish
OPERATION GUIDANCE tuning, press the OK
key.
/ :MOVE CURSOR 05 Same as step 03.
↓ 06 Same as step 04.
/ :SCROLL 07 End of calibration
↓
L: Lower limit Note: The step of the upper
U: Upper limit table may be omitted
C: Current value corresponding to the
condition.
64
Monitoring System Operation Manual
L: Lower limit
U: Upper limit
/ :MOVE CURSOR
C: Current value
↓
↓
[Calibration]
65
Monitoring System Operation Manual
/ :MOVE CURSOR
L: Lower limit
U: Upper limit
↓
C: Current value
↓
[Calibration]
66
Monitoring System Operation Manual
Go to the
CHECK VALVES [Calibration]
CALIBRATIONS
BLCV ▲ In the calibration screen,
SLCV step number is displayed in
Refer to blue.
“6.6.1.1.All Valves”
↓ ▼
Perform the operation
CALIBRATIONS PRESS TO PERFORM written in the following table
CONTROL VALVES ▲ CALIBRATION in each step.
RELIEF VALVES
PS PRES VALVE
FLOW LIMIT VALVE
CHECK VALVES / :MOVE CURSOR
LEVER/PEDAL/ATCH ▼ ↓
PRESS TO PERFORM
CALIBRATION Step Operation
↓ 01 Raise boom and stick
[Calibration] to the max position.
↓ Then press the OK
/ :MOVE CURSOR key.
↓ ↓ 02 Wait until the oil
Default Screen temperature become
↓ a target
CALIBRATIONS 03 Set the hydraulic lock
CONTROL VALVES ▲
[Calibration Screen] lever to unlock
RELIEF VALVES CALIBRATION TITLE position.
PS PRES VALVE 04 Press the OK key in
FLOW LIMIT VALVE STEP No: STEP NAME order to go the next.
CHECK VALVES
LEVER/PEDAL/ATCH ▼
05 Hold Left lever back.
PRESS TO PERFORM 06 Release all levers
S E
CALIBRATION and pedals.
OPERATION GUIDANCE
07 Press the OK key in
order to go the next.
08 End of calibration.
/ :MOVE CURSOR
↓ Note: The step of the upper
/ :SCROLL table may be omitted
↓ corresponding to the
condition.
S: Start step number
E: End step number
67
Monitoring System Operation Manual
▼
PRESS TO PERFORM / :SCROLL
CALIBRATION
↓
[Calibration]
68
Monitoring System Operation Manual
Go to the
LEVER/PEDAL/ATCH [Calibration]
CALIBRATIONS
ALL ▲ In the calibration screen,
LEFT LEVER F/B step number is displayed in
LEFT LEVER L/R blue.
Refer to
RIGHT LEVER F/B
“6.6.1.1.All Valves”
RIGHT LEVER L/R
↓ LEFT TRV PEDAL ▼
Perform the operation
CALIBRATIONS PRESS TO PERFORM written in the following table
CONTROL VALVES ▲ CALIBRATION in each step.
RELIEF VALVES
PS PRES VALVE
FLOW LIMIT VALVE
CHECK VALVES / :MOVE CURSOR
LEVER/PEDAL/ATCH ▼ ↓
PRESS TO PERFORM
CALIBRATION Step Operation
↓ 01 Press the OK key in
[Calibration] order to go the next.
↓ 02 Release all controls.
/ :MOVE CURSOR Then press the OK
↓ ↓ key.
Default Screen 03 Move controls to both
↓ stops.
CALIBRATIONS Then press the OK
CONTROL VALVES ▲
[Calibration Screen] key.
RELIEF VALVES CALIBRATION TITLE 04 Press the OK key in
PS PRES VALVE order to go the next.
FLOW LIMIT VALVE STEP No: STEP NAME 05 End of calibration.
CHECK VALVES
LEVER/PEDAL/ATCH ▼
PRESS TO PERFORM Note: The step of the upper
S E
CALIBRATION table may be omitted
OPERATION GUIDANCE
corresponding to the
condition.
/ :MOVE CURSOR
↓
/ :SCROLL
↓
69
Monitoring System Operation Manual
/ :MOVE CURSOR
↓
↓
[Calibration]
↓
↓
Default Screen
70
Monitoring System Operation Manual
/ :MOVE CURSOR
↓
↓
[Calibration]
↓
↓
Default Screen
71
Monitoring System Operation Manual
/ :MOVE CURSOR
↓
↓
[Calibration]
↓
↓
Default Screen
72
Monitoring System Operation Manual
/ :MOVE CURSOR
↓
↓
[Calibration]
↓
↓
Default Screen
73
Monitoring System Operation Manual
/ :MOVE CURSOR
↓
↓
[Calibration]
↓
↓
Default Screen
74
Monitoring System Operation Manual
/ :MOVE CURSOR
↓
↓
[Calibration]
↓
↓
Default Screen
75
Monitoring System Operation Manual
/ :MOVE CURSOR
↓
↓
[Calibration]
↓
↓
Default Screen
76
Monitoring System Operation Manual
/ :MOVE CURSOR
↓
↓
[Calibration]
↓
↓
Default Screen
77
Monitoring System Operation Manual
/ :MOVE CURSOR
↓
↓
[Calibration]
↓
↓
Default Screen
78
Monitoring System Operation Manual
/ :MOVE CURSOR
↓
↓
[Calibration]
↓
↓
Default Screen
79
Monitoring System Operation Manual
Go to the
CALIBRATIONS [Calibration] Step Operation
In the calibration screen, 01 Press the OK key in
Refer to step number is displayed in order to go the next.
“6.6.1.1.All Valves” blue. 02 Press the OK key.
↓ 03 -
CALIBRATIONS Perform the operation 04 -
CONTROL VALVES ▲ written in the following table 05 -
RELIEF VALVES in each step. 06 -
PS PRES VALVE 07 -
FLOW LIMIT VALVE
08 -
CHECK VALVES
[Calibration Screen] 09 -
LEVER/PEDAL/ATCH ▼
PRESS TO PERFORM
CALIBRATION TITLE 10 -
CALIBRATION 11 End of calibration.
STEP No: STEP NAME
↓
CALIBRATIONS
RELIEF VALVES ▲
PS PRES VALVE / :SCROLL
FLOW LIMIT VALVE
CHECK VALVES
LEVER/PEDAL/ATCH S: Start step number
ENGINE SPEED ▼ E: End step number
PRESS TO PERFORM
CALIBRATION
/ :MOVE CURSOR
↓
↓
[Calibration]
↓
↓
Default Screen
80
Monitoring System Operation Manual
Go to the
CALIBRATIONS [Calibration] Step Operation
In the calibration screen, 01 Connect the speed
Refer to step number is displayed in sensor to the fan.
“6.6.1.1.All Valves” blue. Then press the OK
↓ key in order to go the
CALIBRATIONS Perform the operation next.
CONTROL VALVES ▲ written in the following table 02 Press the right key or
RELIEF VALVES in each step. the left key in order to
PS PRES VALVE increase or decrease
FLOW LIMIT VALVE the current value.
CHECK VALVES And tune the fan
LEVER/PEDAL/ATCH ▼
[Calibration Screen] speed to the target.
PRESS TO PERFORM
CALIBRATION TITLE When you finish
CALIBRATION
tuning, press the OK
STEP No: STEP NAME key.
03 Same as step 02.
/ :MOVE CURSOR 04 End of calibration
L U
↓ C
OPERATION GUIDANCE Note: The step of the upper
↓ table may be omitted
CALIBRATIONS corresponding to the
PS PRES VALVE ▲ condition.
FLOW LIMIT VALVE
CHECK VALVES / :SCROLL
LEVER/PEDAL/ATCH
ENGINE SPEED L: Lower limit
FAN SPEED ▼ U: Upper limit
PRESS TO PERFORM C: Current value
CALIBRATION
/ :MOVE CURSOR
↓
↓
[Calibration]
↓
↓
Default Screen
81
Monitoring System Operation Manual
Go to the
DEVICE TEST When the sweep test is
SERVICE
DESIRED ENG SPEED ▲ activated, press the OK key
POWER SHIFT PRES in order to stop the sweep
FLOW LIMIT PRES test.
Refer to
A1 VALVE EXTEND
“6.Service”
A1 VALVE RETRACT
↓ A3 VALVE EXTEND ▼ [Device Test Screen]
PRESS TO PERFORM DESIRED ENG SPEED
SERVICE
DEVICE TEST ▲
MAINTENANCE ▲
02: ACTIVATING
PASSWORD CHANGE
ENGINE SPEED
DIAGNOSTIC
----[rpm]
ECM INFO
STATUS / :MOVE CURSOR
▼
CALIBRATIONS ▼ ↓
PRESS TO CHANGE
MAINTE INFO
↓
[Device Test] :BACK
↓ :SWEEP START
/ :-/+
/ :MOVE CURSOR
↓ ↓
Default Screen
↓
SERVICE
PASSWORD CHANGE ▲ [Device Test]
DIAGNOSTIC When "01:STAND BY" is
ECM INFO
displayed on the screen,
STATUS
press the OK key in order to
CALIBRATIONS
DEVICE TEST ▼
start device test.
PRESS TO PERFORM
DEVICE TEST In this screen, the following
item can be tested.
82
Monitoring System Operation Manual
83
Monitoring System Operation Manual
84
Monitoring System Operation Manual
/ :MOVE CURSOR
↓
↓
DEVICE TEST
DESIRED ENG SPEED ▲
POWER SHIFT PRES Attachment Valve #1
FLOW LIMIT PRES
Extend Pressure
A1 VALVE EXTEND
A1 VALVE RETRACT
Command
A3 VALVE EXTEND ▼ Press the right key or the
PRESS TO PERFORM left key in order to increase
DEVICE TEST or decrease attachment
valve #1 extend pressure
command.
85
Monitoring System Operation Manual
/ :MOVE CURSOR
↓
↓
DEVICE TEST
DESIRED ENG SPEED ▲
POWER SHIFT PRES Attachment Valve #1
FLOW LIMIT PRES
Retract Pressure
A1 VALVE EXTEND
A1 VALVE RETRACT
Command
A3 VALVE EXTEND ▼ Press the right key or the
PRESS TO PERFORM left key in order to increase
DEVICE TEST or decrease attachment
valve #1 retract pressure
command.
86
Monitoring System Operation Manual
/ :MOVE CURSOR
↓
↓
DEVICE TEST
DESIRED ENG SPEED ▲
POWER SHIFT PRES Attachment Valve #3
FLOW LIMIT PRES
Extend Pressure
A1 VALVE EXTEND
A1 VALVE RETRACT
Command
A3 VALVE EXTEND ▼ Press the right key or the
PRESS TO PERFORM left key in order to increase
DEVICE TEST or decrease attachment
valve #3 extend pressure
command.
87
Monitoring System Operation Manual
/ :MOVE CURSOR
↓
↓
DEVICE TEST
POWER SHIFT PRES ▲
FLOW LIMIT PRES Attachment Valve #3
A1 VALVE EXTEND
Retract Pressure
A1 VALVE RETRACT
A3 VALVE EXTEND
Command
A3 VALVE RETRACT ▼ Press the right key or the
PRESS TO PERFORM left key in order to increase
DEVICE TEST or decrease attachment
valve #3 retract pressure
command.
88
Monitoring System Operation Manual
/ :MOVE CURSOR
↓
↓
DEVICE TEST
FLOW LIMIT PRES ▲
A1 VALVE EXTEND Attachment Variable
A1 VALVE RETRACT
Relief Valve #1 Pressure
A3 VALVE EXTEND
A3 VALVE RETRACT
Command
A1 RLF VALVE ▼ Press the right key or the
PRESS TO PERFORM left key in order to increase
DEVICE TEST or decrease attachment
variable relief valve #1
pressure command.
89
Monitoring System Operation Manual
/ :MOVE CURSOR
↓
↓
DEVICE TEST
A1 VALVE EXTEND ▲
A1 VALVE RETRACT Attachment Variable
A3 VALVE EXTEND
Relief Valve #2 Pressure
A3 VALVE RETRACT
A1 RLF VALVE
Command
A2 RLF VALVE ▼ Press the right key or the
PRESS TO PERFORM left key in order to increase
DEVICE TEST or decrease attachment
variable relief valve #2
pressure command.
90
Monitoring System Operation Manual
/ :MOVE CURSOR
↓
91
Monitoring System Operation Manual
/ :MOVE CURSOR
↓
92
Monitoring System Operation Manual
93
Monitoring System Operation Manual
365C/385C
Display 345C Description
TRAVEL SPEED SHIFT x x Travel Speed Solenoid Override
SWING BREAK SOL x x Swing Brake Solenoid Override
TRV ALARM x x Travel Alarm Override
SYSTEM PRES UP x Front System High Pressure Solenoid Override
NEUTRAL FLOW BYPASS x Neutral Flow Bypass Solenoid Override
ANTI DRIFT BOOM x Boom Anti Drift Solenoid Override
ANTI DRIFT STICK x Stick Anti Drift Solenoid Override
AUTO LUB RELAY x Auto Lube Solenoid Override
REVERSE FAN SOL x x Auto Reverse Fan Solenoid Override
1P/2P CHANGE SOL x Auxiliary Circuit Flow Combining Solenoid Override
FAULT ALARM x Action Alarm Override
1/2WAY CHANGE SOL x One Way / Two Way Valve Solenoid Override
RELIEF CHK SOL #1 x Relief Valve #1 Check Valve Solenoid Override
RELIEF CHK SOL #2 x Relief Valve #2 Check Valve Solenoid Override
DESIRED ENG SPEED x x Desired Engine Speed
BOOM EXTEND x Boom Cylinder Rod Extend Solenoid Current Override
BOOM RETRACT x Boom Cylinder Rod Retract Solenoid Current Override
STICK EXTEND x Stick Cylinder Rod Extend Solenoid Current Override
STICK RETRACT x Stick Cylinder Rod Retract Solenoid Current Override
BUCKET EXTEND x Bucket Cylinder Rod Extend Solenoid Current Override
BUCKET RETRACT x Bucket Cylinder Rod Retract Solenoid Current Override
SWING LEFT x Swing Left Solenoid Current Override
SWING RIGHT x Swing Right Solenoid Current Override
TRV LEFT FW x Left Travel Forward Solenoid Current Override
TRV LEFT BW x Left Travel Backward Solenoid Current Override
TRV RIGHT FW x Right Travel Forward Solenoid Current Override
TRV RIGHT BW x Right Travel Backward Solenoid Current Override
BM LOWERING CHECK x Boom Lowering Check/Modulation Valve Solenoid Current Override
ST LOWERING CHECK x Stick Lowering Check/Modulation Valve Solenoid Current Override
ATCH EXTEND x Attachment Extend/CW Solenoid Current Override
ATCH RETRACT x Attachment Retract/CCW Solenoid Current Override
MID CURCIT EXTEND x Medium Pressure Circuit#1-A Solenoid Current Override
MID CURCIT RETRACT x Medium Pressure Circuit#1-B Solenoid Current Override
POWER SHIFT PRES x Implement Pump Power Shift Pressure Solenoid Current Override
SWING PUMP SWASH x Swash Plate Solenoid Current Override
FAN MOTOR SPEED x x Fan Motor Speed
94
Monitoring System Operation Manual
Go to the
CONFIGURATIONS [Configuration]
SERVICE
ATCH PARTS INST ▲ Press the up key or the
TOOL INSTALLATION down key in order to
CONTROL INST highlight the item you want
Refer to
FRONT LINKAGE
“6.Service” to change setting.
PRODUCT ID
↓ PARAMETER SETTING ▼
SERVICE PRESS TO CONFIGURE And press the OK key in
MAINTENANCE ▲ ATTACHMENT PARTS order to move a highlight to
PASSWORD CHANGE INSTALLATION data value.
DIAGNOSTIC (Ref. next figure)
ECM INFO
STATUS / :MOVE CURSOR ATCH PARTS INST
CALIBRATIONS ▼ ↓ HYD OIL TYPE ▲
PRESS TO CHANGE MINERAL
MAINTE INFO TRAVEL ALARM
↓
NOT CONFIGURED
ATCH PARTS INST
WATER SEPARATOR SW
HYD OIL TYPE ▲
NOT CONFIGURED ▼
MINERAL
/ :MOVE CURSOR PRESS TO SET
TRAVEL ALARM
↓ NOT CONFIGURED
DATA
WATER SEPARATOR SW
↓ NOT CONFIGURED ▼
SERVICE PRESS TO CHANGE
/ :CHANGE VALUE
ECM INFO ▲ DATA
STATUS
CALIBRATIONS Then press the up key and
DEVICE TEST the down key in order to
OVERRIDE / :MOVE CURSOR change the value.
CONFIGURATIONS ▼ ↓
PRESS TO CONFIGURE [Configuration] After changing to the value
MACHINE ECM ↓ you want, press the OK key
in order to set the value into
↓ a machine controller.
/ :MOVE CURSOR Default Screen
↓
95
Monitoring System Operation Manual
Go to the
TOOL INSTALLATION [Configuration]
CONFIGURATIONS
MACHINE APPLICATION ▲ Press the up key or the
SPECIAL APPLI down key in order to
ATCH ECM INSTAL highlight the item you want
Refer to
NOT CONFIGURED
“6.9.1.Attachment Parts to change setting.
Installation” FLOW LIMIT VALVE
NOT CONFIGURED ▼
↓ PRESS TO CHANGE And press the OK key in
CONFIGURATIONS DATA order to move a highlight to
ATCH PARTS INST ▲ data value.
TOOL INSTALLATION (Ref. next figure)
CONTROL INST
FRONT LINKAGE / :MOVE CURSOR TOOL INSTALLATION
PRODUCT ID ↓ MACHINE APPLICATION ▲
PARAMETER SETTING ▼ [Configuration] SPECIAL APPLI
PRESS TO CONFIGURE ATCH ECM INSTAL
↓
ATACHMENT PARTS NOT CONFIGURED
INSTALLATION FLOW LIMIT VALVE
↓ NOT CONFIGURED ▼
Default Screen PRESS TO SET
/ :MOVE CURSOR DATA
↓
↓
/ :CHANGE VALUE
CONFIGURATIONS
ATCH PARTS INST ▲
TOOL INSTALLATION Then press the up key and
CONTROL INST the down key in order to
FRONT LINKAGE change the value.
PRODUCT ID
PARAMETER SETTING ▼ After changing to the value
PRESS TO CONFIGURE you want, press the OK key
TOOL INSTALLATION in order to set the value into
a machine controller.
/ :MOVE CURSOR
↓
96
Monitoring System Operation Manual
Go to the
CONTROL INST [Configuration]
CONFIGURATIONS
LEFT JOYSTICK SW #1 ▲ Press the up key or the
NOT CONFIGURED down key in order to
LEFT JOYSTICK SW #2 highlight the item you want
Refer to
NOT CONFIGURED
“6.9.1.Attachment Parts to change setting.
Installation” RIGHT JOYSTICK SW #1
NOT CONFIGURED ▼
↓ PRESS TO CHANGE And press the OK key in
CONFIGURATIONS DATA order to move a highlight to
ATCH PARTS INST ▲ data value.
TOOL INSTALLATION (Ref. next figure)
CONTROL INST
FRONT LINKAGE / :MOVE CURSOR CONTROL INST
PRODUCT ID ↓ LEFT JOYSTICK SW #1 ▲
PARAMETER SETTING ▼ [Configuration] NOT CONFIGURED
PRESS TO CONFIGURE LEFT JOYSTICK SW #2
↓
ATACHMENT PARTS NOT CONFIGURED
INSTALLATION RIGHT JOYSTICK SW #1
↓ NOT CONFIGURED ▼
Default Screen PRESS TO SET
/ :MOVE CURSOR DATA
↓
↓
/ :CHANGE VALUE
CONFIGURATIONS
ATCH PARTS INST ▲
TOOL INSTALLATION Then press the up key and
CONTROL INST the down key in order to
FRONT LINKAGE change the value.
PRODUCT ID
PARAMETER SETTING ▼ After changing to the value
PRESS TO CONFIGURE you want, press the OK key
CONTROLS INSTALLATION in order to set the value into
a machine controller.
/ :MOVE CURSOR
↓
97
Monitoring System Operation Manual
Go to the
CONFIGURATIONS FRONT LINKAGE [Configuration]
BUCKET TYPE ▲ Press the up key or the
Refer to EXCAVATION down key in order to
“6.9.1.Attachment Parts highlight the item you want
Installation” to change setting.
↓ ▼
CONFIGURATIONS PRESS TO CHANGE And press the OK key in
ATCH PARTS INST ▲ DATA order to move a highlight to
TOOL INSTALLATION data value.
CONTROL INST (Ref. next figure)
FRONT LINKAGE
PRODUCT ID / :MOVE CURSOR FRONT LINKAGE
PARAMETER SETTING ▼
↓ BUCKET TYPE ▲
PRESS TO CONFIGURE
[Configuration] EXCAVATION
ATACHMENT PARTS
INSTALLATION ↓
↓ ▼
/ :MOVE CURSOR Default Screen PRESS TO SET
↓ DATA
↓
CONFIGURATIONS
ATCH PARTS INST ▲
/ :CHANGE VALUE
TOOL INSTALLATION
CONTROL INST Then press the up key and
FRONT LINKAGE the down key in order to
PRODUCT ID change the value.
PARAMETER SETTING ▼
PRESS TO CONFIGURE After changing to the value
FRONT LINKAGE
you want, press the OK key
in order to set the value into
a machine controller.
/ :MOVE CURSOR
↓
98
Monitoring System Operation Manual
Go to the
PRODUCT ID [Configuration]
CONFIGURATIONS
PRODUCT ID ▲ Press the OK key in order to
ZZZ01234 move a highlight to data
Refer to value.
“6.9.1.Attachment Parts (Ref. next figure)
Installation”
▼
↓ PRESS TO CHANGE PRODUCT ID
CONFIGURATIONS DATA PRODUCT ID ▲
/ :MOVE CURSOR
↓
99
Monitoring System Operation Manual
Go to the
PARAMETER SETTING [Configuration]
CONFIGURATIONS
ENGINE SPEED ▲ Press the up key or the
DIAL TORQUE down key in order to
AEC highlight the item you want
Refer to
TRV SPEED SHIFT
“6.9.1.Attachment Parts to change setting.
Installation” OVER LOAD WARNING
ONE TOUCH LOW IDLE ▼
↓ PRESS TO SET And press the OK key in
CONFIGURATIONS ENGINE SPEED order to move a highlight to
ATCH PARTS INST ▲ data value.
TOOL INSTALLATION (Ref. next figure)
CONTROL INST
FRONT LINKAGE / :MOVE CURSOR ENGINE SPEED
PRODUCT ID ↓ DIAL 1 SPEED ▲
PARAMETER SETTING ▼ 900.0[RPM]
PRESS TO CONFIGURE DIAL 2 SPEED
ATACHMENT PARTS
↓
1020.0[RPM]
INSTALLATION ENGINE SPEED
DIAL 3 SPEED
DIAL 1 SPEED ▲
1160.0[RPM] ▼
900.0[RPM]
PRESS TO SET
/ :MOVE CURSOR DIAL 2 SPEED
DATA
1020.0[RPM]
↓
DIAL 3 SPEED
1160.0[RPM] ▼
↓ PRESS TO CHANGE
/ :CHANGE VALUE
CONFIGURATIONS DATA
ATCH PARTS INST ▲
TOOL INSTALLATION Then press the up key and
CONTROL INST the down key in order to
FRONT LINKAGE / :MOVE CURSOR change the value.
PRODUCT ID ↓
PARAMETER SETTING ▼ [Configuration] After changing to the value
PRESS TO SET
↓ you want, press the OK key
PARAMETERS in order to set the value into
↓ a machine controller.
Default Screen
/ :MOVE CURSOR
↓
100
Monitoring System Operation Manual
Go to the
DIAL TORQUE [Configuration]
PARAMETER SETTING
DIAL 1 TORQUE ▲ Press the up key or the
34[%] down key in order to
DIAL 2 TORQUE highlight the item you want
Refer to
44[%]
“6.9.5.1.Parameter to change setting.
Setting” DIAL 3 TORQUE
54[%] ▼
↓ PRESS TO CHANGE And press the OK key in
PARAMETER SETTING DATA order to move a highlight to
ENGINE SPEED ▲ data value.
DIAL TORQUE (Ref. next figure)
AEC
TRV SPEED SHIFT / :MOVE CURSOR DIAL TORQUE
OVER LOAD WARNING ↓ DIAL 1 TORQUE ▲
ONE TOUCH LOW IDLE ▼ [Configuration] 34[%]
PRESS TO SET DIAL 2 TORQUE
↓
ENGINE SPEED 44[%]
DIAL 3 TORQUE
↓ 54[%] ▼
Default Screen PRESS TO SET
/ :MOVE CURSOR DATA
↓
↓
/ :CHANGE VALUE
PARAMETER SETTING
ENGINE SPEED ▲
DIAL TORQUE Then press the up key and
AEC the down key in order to
TRV SPEED SHIFT change the value.
OVER LOAD WARNING
ONE TOUCH LOW IDLE ▼ After changing to the value
PRESS TO SET you want, press the OK key
DIAL TORQUE in order to set the value into
a machine controller.
/ :MOVE CURSOR
↓
101
Monitoring System Operation Manual
Go to the
AEC [Configuration]
PARAMETER SETTING
AEC2 ENG SPEED ▲ Press the up key or the
1300[RPM] down key in order to
AEC2 DELAY TIME highlight the item you want
Refer to
3[sec]
“6.9.5.1.Parameter to change setting.
Setting”
▼
↓ PRESS TO CHANGE And press the OK key in
PARAMETER SETTING DATA order to move a highlight to
ENGINE SPEED ▲ data value.
DIAL TORQUE (Ref. next figure)
AEC
TRV SPEED SHIFT / :MOVE CURSOR AEC
OVER LOAD WARNING ↓ AEC2 ENG SPEED ▲
ONE TOUCH LOW IDLE ▼ [Configuration] 1300[RPM]
PRESS TO SET AEC2 DELAY TIME
↓
ENGINE SPEED 3[sec]
↓ ▼
Default Screen PRESS TO SET
/ :MOVE CURSOR DATA
↓
↓
/ :CHANGE VALUE
PARAMETER SETTING
ENGINE SPEED ▲
DIAL TORQUE Then press the up key and
AEC the down key in order to
TRV SPEED SHIFT change the value.
OVER LOAD WARNING
ONE TOUCH LOW IDLE ▼ After changing to the value
PRESS TO SET you want, press the OK key
AEC in order to set the value into
a machine controller.
/ :MOVE CURSOR
↓
102
Monitoring System Operation Manual
6.9.6.4. Travel Speed Shft Pressure (345C/300D Medium) SERVICE PASSWORD REQUIRED
( MAIN MENU → SERVICE → CONFIGURATIONS → PARAMETER SETTING → TRV SPEED SHIFT )
Go to the
TRV SPEED SHIFT [Configuration]
PARAMETER SETTING
LOW PRES ▲ Press the up key or the
20000[KPa] down key in order to
HIGH PRES highlight the item you want
Refer to
32000[KPa]
“6.9.5.1.Parameter to change setting.
Setting” LOW DELAY
0.4[sec] ▼
↓ PRESS TO CHANGE And press the OK key in
PARAMETER SETTING DATA order to move a highlight to
ENGINE SPEED ▲ data value.
DIAL TORQUE (Ref. next figure)
AEC
TRV SPEED SHIFT / :MOVE CURSOR TRV SPEED SHIFT
OVER LOAD WARNING ↓ LOW PRES ▲
ONE TOUCH LOW IDLE ▼ [Configuration] 20000[KPa]
PRESS TO SET HIGH PRES
↓
ENGINE SPEED 32000[KPa]
LOW DELAY
↓ 0.4[sec] ▼
Default Screen PRESS TO SET
/ :MOVE CURSOR DATA
↓
↓
/ :CHANGE VALUE
PARAMETER SETTING
ENGINE SPEED ▲
DIAL TORQUE Then press the up key and
AEC the down key in order to
TRV SPEED SHIFT change the value.
OVER LOAD WARNING
ONE TOUCH LOW IDLE ▼ After changing to the value
PRESS TO SET you want, press the OK key
TRAVEL SPEED SHIFT in order to set the value into
a machine controller.
/ :MOVE CURSOR
↓
103
Monitoring System Operation Manual
Go to the
OVER LOAD WARNING [Configuration]
PARAMETER SETTING
OLWD THRESH PRES ▲ Press the OK key in order to
32000[KPa] move a highlight to data
Refer to value.
“6.9.5.1.Parameter (Ref. next figure)
Setting”
▼
↓ PRESS TO CHANGE OVER LOAD WARNING
PARAMETER SETTING DATA OLWD THRESH PRES ▲
ENGINE SPEED ▲
32000[KPa]
DIAL TORQUE
AEC
TRV SPEED SHIFT / :MOVE CURSOR
▼
OVER LOAD WARNING ↓
ONE TOUCH LOW IDLE PRESS TO SET
▼ [Configuration] DATA
PRESS TO SET
↓
ENGINE SPEED
↓
/ :CHANGE VALUE
Default Screen
/ :MOVE CURSOR
↓ Then press the up key and
the down key in order to
↓ change the value.
PARAMETER SETTING
ENGINE SPEED ▲
After changing to the value
DIAL TORQUE you want, press the OK key
AEC in order to set the value into
TRV SPEED SHIFT a machine controller.
OVER LOAD WARNING
ONE TOUCH LOW IDLE ▼
PRESS TO SET
OVER LOAD WARNING
/ :MOVE CURSOR
↓
104
Monitoring System Operation Manual
Go to the
ONE TOUCH LOW IDLE [Configuration]
PARAMETER SETTING
ONE TOUCH ENG SPEED ▲ Press the OK key in order to
1300[RPM] move a highlight to data
Refer to value.
“6.9.5.1.Parameter (Ref. next figure)
Setting”
▼
↓ PRESS TO CHANGE ONE TOUCH LOW IDLE
PARAMETER SETTING DATA ONE TOUCH ENG SPEED ▲
ENGINE SPEED ▲
1300[RPM]
DIAL TORQUE
AEC
TRV SPEED SHIFT / :MOVE CURSOR
▼
OVER LOAD WARNING ↓
ONE TOUCH LOW IDLE PRESS TO SET
▼ [Configuration] DATA
PRESS TO SET
↓
ENGINE SPEED
↓
/ :CHANGE VALUE
Default Screen
/ :MOVE CURSOR
↓ Then press the up key and
the down key in order to
↓ change the value.
PARAMETER SETTING
ENGINE SPEED ▲
After changing to the value
DIAL TORQUE you want, press the OK key
AEC in order to set the value into
TRV SPEED SHIFT a machine controller.
OVER LOAD WARNING
ONE TOUCH LOW IDLE ▼
PRESS TO SET
ONE TOUCH LOW IDLE
/ :MOVE CURSOR
↓
105
Monitoring System Operation Manual
Go to the
GAIN/RESPONSE [Configuration]
PARAMETER SETTING
SOFT MODE GAIN ▲ Press the up key or the
4 down key in order to
SOFT MODE RESPONSE highlight the item you want
Refer to
2
“6.9.5.1.Parameter to change setting.
Setting” NORMAL MODE GAIN
4 ▼
↓ PRESS TO CHANGE And press the OK key in
PARAMETER SETTING DATA order to move a highlight to
ENGINE SPEED ▲ data value.
DIAL TORQUE (Ref. next figure)
AEC
TRV SPEED SHIFT / :MOVE CURSOR GAIN/RESPONSE
OVER LOAD WARNING ↓ SOFT MODE GAIN ▲
ONE TOUCH LOW IDLE ▼ [Configuration] 4
PRESS TO SET SOFT MODE RESPONSE
↓
ENGINE SPEED 2
NORMAL MODE GAIN
↓ 4 ▼
Default Screen PRESS TO SET
/ :MOVE CURSOR DATA
↓
↓
/ :CHANGE VALUE
PARAMETER SETTING
DIAL TORQUE ▲
AEC Then press the up key and
TRV SPEED SHIFT the down key in order to
OVER LOAD WARNING change the value.
ONE TOUCH LOW IDLE
GAIN/RESPONSE ▼ After changing to the value
PRESS TO SET you want, press the OK key
GAIN/RESPONSE in order to set the value into
a machine controller.
/ :MOVE CURSOR
↓
106
Monitoring System Operation Manual
Go to the
AUTO LUB SYSTEM [Configuration]
PARAMETER SETTING
DURATION TIME ▲ Press the up key or the
4[min] down key in order to
INTERVAL TIME highlight the item you want
Refer to
30[min]
“6.9.5.1.Parameter to change setting.
Setting”
▼
↓ PRESS TO CHANGE And press the OK key in
PARAMETER SETTING DATA order to move a highlight to
ENGINE SPEED ▲ data value.
DIAL TORQUE (Ref. next figure)
AEC
TRV SPEED SHIFT / :MOVE CURSOR AUTO LUB SYSTEM
OVER LOAD WARNING ↓ DURATION TIME ▲
ONE TOUCH LOW IDLE ▼ [Configuration] 4[min]
PRESS TO SET INTERVAL TIME
↓
ENGINE SPEED 30[min]
↓ ▼
Default Screen PRESS TO SET
/ :MOVE CURSOR DATA
↓
↓
/ :CHANGE VALUE
PARAMETER SETTING
AEC ▲
TRV SPEED SHIFT Then press the up key and
OVER LOAD WARNING the down key in order to
ONE TOUCH LOW IDLE change the value.
GAIN/RESPONSE
AUTO LUB SYSTEM ▼ After changing to the value
PRESS TO SET you want, press the OK key
AUTO LUB SYSTEM in order to set the value into
a machine controller.
/ :MOVE CURSOR
↓
107
Monitoring System Operation Manual
Go to the
UHD [Configuration]
PARAMETER SETTING
UHD REQUESTED FLOW ▲ Press the OK key in order to
40[L/min] move a highlight to data
Refer to value.
“6.9.5.1.Parameter (Ref. next figure)
Setting”
▼
↓ PRESS TO CHANGE UHD
PARAMETER SETTING DATA UHD REQUESTED FLOW ▲
ENGINE SPEED ▲
40[L/min]
DIAL TORQUE
AEC
TRV SPEED SHIFT / :MOVE CURSOR
▼
OVER LOAD WARNING ↓
ONE TOUCH LOW IDLE PRESS TO SET
▼ [Configuration] DATA
PRESS TO SET
↓
ENGINE SPEED
↓
/ :CHANGE VALUE
Default Screen
/ :MOVE CURSOR
↓ Then press the up key and
the down key in order to
↓ change the value.
PARAMETER SETTING
TRV SPEED SHIFT ▲
After changing to the value
OVER LOAD WARNING you want, press the OK key
ONE TOUCH LOW IDLE in order to set the value into
GAIN/RESPONSE a machine controller.
AUTO LUB SYSTEM
UHD ▼
PRESS TO SET
UHD
/ :MOVE CURSOR
↓
108
Monitoring System Operation Manual
Go to the
REVERSE FAN [Configuration]
PARAMETER SETTING
OPERATION TIME ▲ Press the OK key in order to
100[sec] move a highlight to data
Refer to value.
“6.9.5.1.Parameter (Ref. next figure)
Setting”
▼
↓ PRESS TO CHANGE REVERSE FAN
PARAMETER SETTING DATA OPERATION TIME ▲
ENGINE SPEED ▲
100[sec]
DIAL TORQUE
AEC
TRV SPEED SHIFT / :MOVE CURSOR
▼
OVER LOAD WARNING ↓
ONE TOUCH LOW IDLE PRESS TO SET
▼ [Configuration] DATA
PRESS TO SET
↓
ENGINE SPEED
↓
/ :CHANGE VALUE
Default Screen
/ :MOVE CURSOR
↓ Then press the up key and
the down key in order to
↓ change the value.
PARAMETER SETTING
OVER LOAD WARNING ▲
After changing to the value
ONE TOUCH LOW IDLE you want, press the OK key
GAIN/RESPONSE in order to set the value into
AUTO LUB SYSTEM a machine controller.
UHD
REVERSE FAN ▼
PRESS TO SET
REVERSE FAN
/ :MOVE CURSOR
↓
109
Monitoring System Operation Manual
M-PUMP/LI TORQUE
Go to the
LOAD INIT TORQUE ▲
[Configuration]
PARAMETER SETTING 5[%]
Press the OK key in order to
Refer to move a highlight to data
“6.9.5.1.Parameter value.
Setting” (Ref. next figure)
▼
↓ PRESS TO CHANGE
PARAMETER SETTING DATA M-PUMP/LI TORQUE
ENGINE SPEED ▲ LOAD INIT TORQUE ▲
DIAL TORQUE 5[%]
AEC
TRV SPEED SHIFT / :MOVE CURSOR
OVER LOAD WARNING ↓
ONE TOUCH LOW IDLE ▼ [Configuration] ▼
PRESS TO SET PRESS TO SET
↓
ENGINE SPEED DATA
↓
Default Screen
/ :MOVE CURSOR / :CHANGE VALUE
↓
Then press the up key and
↓ the down key in order to
PARAMETER SETTING change the value.
ONE TOUCH LOW IDLE ▲
GAIN/RESPONSE After changing to the value
AUTO LUB SYSTEM you want, press the OK key
UHD in order to set the value into
REVERSE FAN a machine controller.
M-PUMP/LI TORQUE ▼
PRESS TO SET
REVERSE FAN
/ :MOVE CURSOR
↓
110
Monitoring System Operation Manual
365C/385C
345C
Display Description
111
Monitoring System Operation Manual
365C/385C
345C
Display Description
112
Monitoring System Operation Manual
365C/385C
345C
Display Description
113
Monitoring System Operation Manual
365C/385C
345C
Display Description
ONE TOUCH LOW IDLE : One Touch Low Idle Engine Speed
ONE TOUCH ENG SPEED x x One Touch Engine Speed Setting
114
Monitoring System Operation Manual
Go to the
TOOL PROGRAM [Configuration]
SERVICE
TOOL #1 ▲ Press the up key or the
TOOL #2 down key in order to
TOOL #3 highlight the item you want
Refer to
TOOL #4
“6.Service” to change setting.
TOOL #5
↓ ▼
SERVICE PRESS TO PROGRAM And press the OK key in
MAINTENANCE ▲ TOOL #1 order to move a highlight to
PASSWORD CHANGE data value.
DIAGNOSTIC (Ref. next figure)
ECM INFO
STATUS / :MOVE CURSOR TOOL #??
CALIBRATIONS ▼ ↓ NAME ▲
PRESS TO CHANGE 0
MAINTE INFO MAX DIAL
+
10
MIN DIAL
↓ 1 ▼
/ :MOVE CURSOR PRESS TO SET
Select a tool
↓ DATA
↓
↓ TOOL #??
NAME ▲ / :MOVE CURSOR
SERVICE / :CHANGE VALUE
STATUS ▲
0
CALIBRATIONS MAX DIAL
DEVICE TEST 10 Then press the up key and
OVERRIDE MIN DIAL the down key in order to
CONFIGURATIONS 1 ▼ change the value.
TOOL PROGRAM ▼ PRESS TO CHANGE
DATA
PRESS TO PROGRAM After changing to the value
TOOL you want, press the OK key
in order to set the value into
/ :MOVE CURSOR a machine controller.
/ :MOVE CURSOR ↓
[Configuration] Note: The indication item
↓
varies by the model. And
↓
the item which is checked at
↓ the next table may not be
↓ indicated by the machine
Default Screen configuration.
115
Monitoring System Operation Manual
365C/385C
345C
Display Description
NAME x x Tool Program Name
MAX DIAL x x Tool Program Maximum Throttle Dial Position
MIN DIAL - x Tool Program Minimum Throttle Dial Position
UNDERSPEED ENABLE - x Tool Program Under Speed Enable
COMBINER ENABLE - x Tool Program Two Pump Flow Combine Enable
WARNING TEMP - x Tool Program Hydraulic Temperature High Warning Event Threshold
ONE OR TWO WAY - x Tool Program One Way/ Two Way Valve Mode
VAR RELIEF #1 PRES - x Tool Program Variable Relief Valve #1 Pressure
VAR RELIEF #2 PRES - x Tool Program Variable Relief Valve #2 Pressure
F2 DERATE MAX PRES - x F2 Type Valve Maximum Derate Control Pressure
F2 SQEZ START PRES - x F2 Type Valve Pressure Derate Start Pressure
F2 SQEZ END PRES - x F2 Type Valve Pressure Derate End Pressure
Multiple Operation Maximum Extend Pilot Pres for Combined
F2 MULTI OPE EXTND - x
Attachment Valve
Multiple Operation Maximum Retract Pilot Pres for Combined
F2 MULTI OPE RETCT - x
Attachment Valve
MOD L JOYSTK SW #1 x x Tool Program Left Joystick Switch #1 Control Mode
MOD L JOYSTK SW #2 x x Tool Program Left Joystick Switch #2 Control Mode
MOD R JOYSTK SW #1 x x Tool Program Right Joystick Switch #1 Control Mode
MOD R JOYSTK SW #2 x x Tool Program Right Joystick Switch #2 Control Mode
JOYSTK INPUT #1(PR) x - Tool Program Proportional Joystick #1 Valve Configuration
JOYSTK INPUT #4(PR) x - Tool Program Proportional Joystick #4 Valve Configuration
JOYSTK INPUT #1 x - Tool Program Joystick #1 Switch Valve Configuration
JOYSTK INPUT #2 x - Tool Program Joystick #2 Switch Valve Configuration
JOYSTK INPUT #3 x - Tool Program Joystick #3 Switch Valve Configuration
JOYSTK INPUT #4 x - Tool Program Joystick #4 Switch Valve Configuration
MOD L THUMBWHEEL x x Tool Program Left Joystick Thumbwheel Control Mode
MOD R THUMBWHEEL x x Tool Program Right Joystick Thumbwheel Control Mode
ATCH LEFT PEDAL - x Tool Program Left Attachment Pedal Control Mode
ATCH RIGHT PEDAL - x Tool Program Right Attachment Pedal Control Mode
ATCH PEDAL x - Tool Program Proportionally Auxiliary Pedal Valve Configuration
116
Monitoring System Operation Manual
365C/385C
345C
Display Description
ATCH #1 TOOL SW - x Tool Program Attachment Switch #1 Control Mode
ATCH #2 TOOL SW - x Tool Program Attachment Switch #2 Control Mode
ATCH #3 TOOL SW - x Tool Program Attachment Switch #3 Control Mode
ATCH #4 TOOL SW - x Tool Program Attachment Switch #4 Control Mode
ATCH VALVE MODE x - Tool Program Auxiliary Valve #1 Mode
ATCH MAX EXT FLOW x - Tool Program Auxiliary Valve #1 Maximum Extend Flow Rate
ATCH EXT OPEN RATE x - Tool Program Auxiliary Valve #1 Extend Open Rate
ATCH EXT CLOSE RATE x - Tool Program Auxiliary Valve #1 Extend Close Rate
ATCH MAX RET FLOW x - Tool Program Auxiliary Valve #1 Maximum Retract Flow Rate
ATCH RET OPEN RATE x - Tool Program Auxiliary Valve #1 Retract Open Rate
ATCH RET CLOSE RATE x - Tool Program Auxiliary Valve #1 Retract Close Rate
PRI MIN EXT FLOW x - Auxiliary Minimum Extend Flow
PRI EXT RED PRES x - Extend Flow Reduction Pressure
PRI EXT RELIEF PRES x - Extend Relief Pressure
PRI MIN RET FLOW x - Auxiliary Minimum Retract Flow
PRI RET RED PRES x - Retract Flow Reduction Pressure
PRI RET RELIEF PRES x - Extend Relief Pressure
Tool Program Medium Pressure Circuit #1-A Maximum Solenoid
MED C1-A MAX SOL x -
Current
Tool Program Medium Pressure Circuit #1-A Minimum Solenoid
MED C1-A MIN SOL x -
Current
MED C1-A OPEN RATE x - Tool Program Medium Pressure Circuit #1-A Open Rate
MED C1-A CLOSE RATE x - Tool Program Medium Pressure Circuit #1-A Close Rate
Tool Program Medium Pressure Circuit #1-B Maximum Solenoid
MED C1-B MAX SOL x -
Current
Tool Program Medium Pressure Circuit #1-B Minimum Solenoid
MED C1-B MIN SOL x -
Current
MED C1-B OPEN RATE x - Tool Program Medium Pressure Circuit #1-B Open Rate
MED C1-B CLOSE RATE x - Tool Program Medium Pressure Circuit #1-B Close Rate
Tool Program Medium Pressure Circuit Main Pump Power Reduction
INIT PUMP POWER RED x x
(Initial)
Tool Program Medium Pressure Circuit Main Pump Power Reduction
TOTAL PUMP POW RED x x
(Total)
117
Monitoring System Operation Manual
365C/385C
345C
Display Description
A1 FLOW - x Tool Program Attachment Valve #1 Flow Setting
A1 MULTI ADD FLOW - x Tool Program Attachment Valve #1 Multi-Operation Additional Flow
A1 NOMINAL PRES - x Tool Program Attachment Valve #1 Nominal Pressure
A1 OPEN TIME - x Tool Program Attachment Valve #1 Open Time
A1 CLOSE TIME - x Tool Program Attachment Valve #1 Close Time
A1 EXTND MAX PRES - x Tool Program Attachment Valve #1 Maximum Extend Pressure
A1 RETCT MAX PRES - x Tool Program Attachment Valve #1 Maximum Retract Pressure
A3 FLOW - x Tool Program Attachment Valve #3 Flow Setting
A3 MULTI ADD FLOW - x Tool Program Attachment Valve #3 Multi-Operation Additional Flow
A3 NOMINAL PRES - x Tool Program Attachment Valve #3 Nominal Pressure
A3 OPEN TIME - x Tool Program Attachment Valve #3 Open Time
A3 CLOSE TIME - x Tool Program Attachment Valve #3 Close Time
A3 EXTND MAX PRES - x Tool Program Attachment Valve #3 Maximum Extend Pressure
A3 RETCT MAX PRES - x Tool Program Attachment Valve #3 Maximum Retract Pressure
118
Monitoring System Operation Manual
119
Monitoring System Operation Manual
120
Monitoring System Operation Manual
121
Monitoring System Operation Manual
122
Monitoring System Operation Manual
123
Monitoring System Operation Manual
124
Monitoring System Operation Manual
125
Monitoring System Operation Manual
126