This document provides troubleshooting steps to diagnose issues with a vehicle's daytime running lamps (DRL) system. It involves checking for power at various components in the DRL circuit, including the DRL module, relay, and headlamps. If power is not present, it directs checking specific circuits for opens that would prevent power from reaching the component. The goal is to isolate the problem component and repair any open circuits found.
This document provides troubleshooting steps to diagnose issues with a vehicle's daytime running lamps (DRL) system. It involves checking for power at various components in the DRL circuit, including the DRL module, relay, and headlamps. If power is not present, it directs checking specific circuits for opens that would prevent power from reaching the component. The goal is to isolate the problem component and repair any open circuits found.
Copyright:
Attribution Non-Commercial (BY-NC)
Available Formats
Download as DOC, PDF, TXT or read online from Scribd
This document provides troubleshooting steps to diagnose issues with a vehicle's daytime running lamps (DRL) system. It involves checking for power at various components in the DRL circuit, including the DRL module, relay, and headlamps. If power is not present, it directs checking specific circuits for opens that would prevent power from reaching the component. The goal is to isolate the problem component and repair any open circuits found.
Copyright:
Attribution Non-Commercial (BY-NC)
Available Formats
Download as DOC, PDF, TXT or read online from Scribd
Did you perform the DRL System Go to Daytime Check? Running 1 -- Go to Step 2 Lights (DRL) System Check 1. Ensure that the park brake is not engaged. 2. Turn the ignition switch to the 2 -- RUN position.
Does the brake indicator lamp light? Go to Step 12 Go to Step 3
1. Turn the ignition switch to the LOCK position. 2. Disconnect the daytime running lamps (DRL) module connector. 3. Turn the ignition switch to the 3 RUN position. -- 4. Connect a test lamp from the DRL module connector, cavity C, to ground.
Does the test lamp light? Go to Step 4 Go to Step 13
Connect a J 35616-200 from cavity C to cavity H of the DRL module 4 connector. --
Does the test lamp light? Go to Step 5 Go to Step 14
1. Remove the DRL relay from the convenience center. 2. Connect a J 35616-200 the DRL 5 -- relay, cavity G6, to ground.
Does the test lamp light? Go to Step 6 Go to Step 15
Connect a J 35616-200 from the DRL relay, cavity G4, to ground. 6 -- Does the test lamp light? Go to Step 7 Go to Step 16 7 1. Turn the ignition switch to the -- Go to Step 8 Go to Step 17 LOCK position. 2. Reconnect the DRL module connector. 3. Turn the ignition switch to the RUN position.
Does the DRL indicator lamp light?
1. Connect a J 39200 from the DRL relay, cavity H6, to B+. Battery 8 2. Measure the voltage. Voltage Is there battery voltage? Go to Step 9 Go to Step 18 Connect a fused jumper from cavity G6 to cavity H4 of the DRL relay. 9 -- Do the low beam headlights light? Go to Step 19 Go to Step 10 1. Re-install the DRL relay. 2. Turn the ignition switch to the RUN position. 3. Disconnect the headlamp connector. 10 -- 4. Connect a test lamp from cavity C (base) or cavity A (quad) to ground.
Does the test lamp light? Go to Step 11 Go to Step 20
Connect a J 39200 , set on ohms, between cavity A and ground. 11 -- Is there continuity? Go to Step 21 Go to Step 22 Refer to Park Brake for diagnosis. Go to Daytime 12 Did you find and correct the condition? -- Running Lights (DRL) System Check -- Repair the open in CKT 39 (PNK) Go to between the instrument panel (IP) fuse Daytime 13 block and the DRL module. -- Running Lights (DRL) Is the repair complete? System Check -- Repair the open in CKT 150 (BLK) Go to between the DRL module and ground Daytime 14 G200. -- Running Lights (DRL) Is the repair complete? System Check -- 15 1. Inspect for an open in CKT 340 -- Go to -- (ORN) between the IP fuse Daytime block and D203. 2. If an open is not found, inspect for an open in CKT 634 (YEL) between D203 and the convenience center. 3. If an open is not found, locate and replace diode D203. Running Lights (DRL) Is the repair complete? System Check Repair the open in CKT 39 (PNK) Go to between splice S213 and the Daytime 16 convenience center. -- Running Lights (DRL) Is the repair complete? System Check -- 1. Inspect for a poor connection or damaged terminals at the DRL module connector. 2. Repair the DRL module connector, as necessary. 17 -- 3. If you do not find a condition at Go to the connector, replace the DRL Daytime module. Running Lights (DRL) Is the repair complete? System Check -- Repair the open in CKT 592 (LT Go to GRN/BLK) between the DRL module Daytime 18 and the convenience center. -- Running Lights (DRL) Is the repair complete? System Check -- Replace the DRL relay. Refer to Go to Daytime Running Lamps (DRL) Relay Daytime 19 Replacement -- Running Lights (DRL) Is the repair complete? System Check -- Repair the open in CKT 12 (TAN) Go to between the DRL relay and left Daytime 20 high/low beam headlamps. -- Running Lights (DRL) Is the repair complete? System Check -- Replace the left and/or the right Go to high/low beam headlamp. Refer to Daytime 21 Headlamp Replacement -- Running Lights (DRL) Is the repair complete? System Check -- Repair the open in CKT 150 between the left high/low beam headlamp and ground G113, and/or repair the open in CKT 250 (BLK) between the right 22 high/low beam headlamp and ground G112.
(International Series of Monographs On Physics) Walter T. Grandy Jr. - Entropy and The Time Evolution of Macroscopic Systems-Oxford University Press, USA (2008) PDF