Professional Documents
Culture Documents
Peter Sandin,
ComAp CEO
heart:
The people, enthusiasm, values and culture that make ComAp ComAp.
The heart of ComAp is our people – they are the centre of our business
and the reason for our success.
Products ....................................................................................
9
> Gen-set controllers ................................................ 11
> Gen-set controllers: Parallel .................................. 21
> Generator and ATS controllers............................... 35
> Mains protections ................................................. 39
> Engine controllers ................................................. 41
> Bi-fuel products .................................................... 49
> Colour displays ..................................................... 53
> Extension Modules and Accessories .................... 59
> PC monitoring and configuration software ............ 71
> Product Comparison Tables ................................. 77
www.youtube.com/ComApControlSystem
The ComAp
Difference
ComAp specializes in creating electronic control and
management solutions for use in the power generation
industries and drive power markets. Our portfolio of
products, software and accessories is designed to
support emergency power, standby power generation
and engine driven applications all over the world.
6
Our eleven subsidiaries in key geographic regions throughout the world,
coupled with our extensive distributor network ensures that ComAp
is always close to our most important partners; our customers. This
local presence is a point of difference with ComAp. It is our focus on
local presence that allows us to ensure that we always have the most
up-to-date and relevant market information, but, more importantly, that
we always have close contact with our customers – helping us remain at
The heart of smart control.
7
ComAp’s Capabilities
Power generation system Complex standby systems, Co-generation, combined Parallel with mains operation
design and supply synchronisation and load share heat and power (CHP) and
including multiple incoming mains tri-generation control systems
Power stations Mains, feeder and load shedding BMS, SCADA and Mains protection
control systems remote monitoring (decoupling relays)
Aircraft ground power control Hydraulic system control Engine driven compressors Marine certified systems
systems including power management and pumps
Mining, agricultural and military Renewable hybrid systems (solar, Water pump and Bi-fuel (gas and diesel)
vehicle control systems wind, hydroelectric) dredging control systems conversion
8 Please note: not all services are available at all subsidiaries and distributors.
Products
9
10
Suitable for:
controllers
Telecom Hospitals
>> Controller for single gen-set operating in >> ECU support (CAN J1939)
prime power applications >> USB one-cord power supply and programing
>> 3 Phase generator voltage measurement >> Standard cut-out dimension 96 × 96 mm
>> Connection type and voltage auto detect >> Outside dimension 118 × 108 mm
>> Various generator and engine protections >> IP 65
>> Icon menu, no text >> UL recognized
>> Automatic or manual GCB control
>> “Zero” power consumption mode
>> Battery voltage, Service time and Running
hours indication
>> All setpoints and I/Os configurable via
front panel
>> Light Tower mode supported
>> Event log (10 events)
>> Up to 3 analog inputs
(shared with binary inputs)
>> COM terminal for analog measurement
>> Up to 6 binary inputs (1 binary input is shared
with binary output)
>> 2 high side – high current outputs
>> 2 high side binary outputs
>> D+ pre-excitation terminal
Order code
IN-NT MRS
12 Gen-set controllers Single
InteliNanoNT Plus InteliNano MRS 3
AMF and MRS Controller with Current Gen-set Controller with 3 Phase
Measurement and Support Voltage & Current Measurement
of EFI Engines
>> AMF and MRS controller in one model >> Controller for single gen-set operating in prime power applications
>> 1/3 Phase generator voltage measurement >> 3 Phase generator voltage & current measurement
(3/3 phase when used as MRS controller) >> Power measurement and energy counters
>> 1 Phase generator current measurement >> Connection type and voltage auto detect
>> 3 Phase mains voltage measurement >> Generator and engine protections
>> Connection type and voltage auto detect >> Symbolic interface
>> Various generator and engine protections >> Automatic or manual GCB control
>> Icon menu, no text >> “Zero” power consumption mode
>> Automatic or manual MCB and GCB control >> Battery voltage, Service time and Running hours indication
>> “Zero” power consumption mode >> Automatic recharge of batteries
>> Battery voltage, Service time and Running hours indication >> Configurable via front panel
>> All setpoints and I/Os configurable via front panel >> Light Tower mode supported
>> Light Tower mode supported >> Event log (15 events)
>> Event log (10 events) >> Up to 6 inputs / Up to 6 outputs
>> Up to 3 analog inputs (shared with binary inputs) >> 2 high current outputs, for Starter and Fuel Solenoid, internally
>> COM terminal for analog measurement connected to the Emergency Stop input
>> Up to 6 binary inputs (1 binary input is shared with binary output) >> D+ pre-excitation terminal
>> 2 high side – high current outputs, 4 high side binary outputs >> Magnetic pickup
>> D+ pre-excitation terminal >> ECU support (CAN J1939)
>> ECU support (CAN J1939) >> USB one-cord power supply and programing
>> USB one-cord power supply and programing >> License free PC configuration software (NanoEdit)
>> Standard cut-out dimension 96 × 96 mm >> Standard cut-out dimension 96 × 96 mm
>> Outside dimension 118 × 108 mm >> Outside dimension 110 × 100 mm
>> IP 65 >> IP 65 (if optional gasket is used)
>> Compact gen-set controller for single operating gen-set >> Compact gen-set controller for single operating gen-set
>> Manual and remote start (MRS) applications >> Manual and remote start (MRS) applications
>> Easy to setup >> Easy to setup
>> Wide gen-set monitoring and protection >> Wide gen-set monitoring and protection
>> Running hours event and performance log >> Outstanding EFI engine support with diagnostic messages
>> Multiple languages (user changeable) in controller, even more in plain text via J1939
in installation suite >> Running hours event and performance log
>> Plug-in extension modules capability >> Multiple languages (user changeable) in controller, even more in
>> Automatic SMS on alarm or event & gen-set control over SMS* installation suite
>> Automatic GCB control >> Plug-in extension modules capability
>> D+ preexcitation terminal >> Automatic SMS on alarm or event & gen-set control over SMS*
>> True RMS measurement >> Automatic GCB control
>> 3 phase power measurement >> D+ preexcitation terminal
>> 3 configurable analog inputs >> True RMS measurement
>> 4 binary inputs >> 3 phase power measurement
>> 4 binary outputs >> 3 configurable analog inputs
>> Modbus support >> 4 binary inputs
>> Optional version available with integrated USB port >> 4 binary outputs
>> Modbus support
>> Optional version available with integrated USB port
IL-NT MRS 3 * Plug-in module required IL-NT MRS 4 * Plug-in module required
>> Compact gen-set controller for single gen-set operating in standby mode >> Compact gen-set controller for single gen-set operating
>> Meets all requirements for Auto Mains Failure (AMF) applications in standby mode
>> Easy to setup >> Meets all requirements for Auto Mains Failure (AMF) applications
>> Wide gen-set monitoring and protection >> Easy to setup
>> Running hours event and performance log >> Wide gen-set monitoring and protection
>> Multiple languages (user changeable) in controller, even more in >> Outstanding EFI engine support with diagnostic messages in plain
installation suite text via J1939
>> Plug-in extension modules capability >> Running hours event and performance log
>> Automatic SMS on alarm or event & gen-set control over SMS* >> Multiple languages (user changeable) in controller, even more in
>> Supports prime power (MRS) applications installation suite
>> Automatic and manual GCB and MCB control >> Plug-in extension modules capability
>> D+ preexcitation terminal >> Automatic SMS on alarm or event & gen-set control over SMS*
>> True RMS measurement >> Supports prime power (MRS) applications
>> 3 phase power measurement >> Automatic and manual GCB and MCB control
>> 3 configurable analog inputs >> D+ preexcitation terminal
>> 4 binary inputs >> True RMS measurement
>> 6 binary outputs >> 3 phase power measurement
>> Modbus Support >> 3 configurable analog inputs
>> Optional version available with integrated USB port >> 4 binary inputs
>> 6 binary outputs
>> Modbus Support
>> Optional version available with integrated USB port
IL-NT AMF 8 * Plug-in module required IL-NT AMF 9 * Plug-in module required
>> Direct communication with EFI engines >> Adjustable choke function
>> Easy to install, configure and use >> Magnetic pickup for precise RPM
>> Wide range of communication capabilities: measurement
• Connection via RS232, RS 485, CAN or USB >> Runhour counter source internal or ECU
• Internet acces using Ethernet >> Possibility to disable protections
• Support fot Modbus RTU and TCP
>> Active SMS and emails in different languages
>> 2× 10 A Binary output for cranking and
fuel solenoid
>> 3 analog inputs / 6 binary inputs / 6 binary
outputs on board
• Option for additional I/Os over modules
>> E-Stop input
>> Slot for plug-in module
>> Flexible event based history with up to 150
events
>> Tier 4 final support
>> Activation of fuel pump Binary outputs based
on Analog inputs
>> Comprehensive gen-set protections
>> Multiple flexible timers
>> True RMS measurement
>> AMR and MRS function in single firmware
>> Up to 3 alternative configurations switchable
by Binary inputs
Order code
>> 5 languages in the controller
IL3LAMF9BAA >> Adjustable D+ level
>> Direct communication with EFI engines >> Direct communication with EFI engines
>> Total remote monitoring and control >> Total remote monitoring and control
>> Easy to install, configure and use >> Cloud-based monitoring and control via WebSupervisor
>> Wide range of communication capabilities via RS232, RS485, CAN or >> Geo-fencing and tracking via WebSupervisor
USB, Ethernet, Modbus RTU and TCP >> Wide range of communication capabilities via RS232, RS485, CAN or
>> Internal PLC support with PLC editor, PLC monitor included USB, Ethernet, GPRS or 4G, Modbus and SNMP protocols
in InteliConfig >> Internal PLC support, PLC editor, PLC monitor included in InteliConfig
>> Active SMS and emails in different languages >> Active SMS and emails in different languages
>> 2× 10 A binary outputs for cranking and fuel solenoid >> 2× 10 A binary outputs for cranking and fuel solenoid
>> 3 analog inputs / 6 binary inputs / 6 binary outputs on board >> 4 analog inputs / 7 binary inputs / 7 binary outputs on board
• Option for additional I/Os over modules • Option for additional I/Os over modules
>> Flexible event based history with up to 350 events >> Flexible event based history with up to 350 events
>> Tier 4 final support >> Tier 4 final support
>> Activation of binary outputs based on analog inputs >> Load shedding and dummy load
>> Comprehensive gen-set protections >> Activation of binary outputs based on analog inputs
>> Multipurpose flexible timers >> Multipurpose flexible timers
>> True RMS measurement >> True RMS measurement
>> Maintanance timers can count to negative* >> Version for low temperature also available
>> Internal or ECU source for running hours* >> Maintanance timers can count to negative*
>> Configurable main screen* >> Internal or ECU source for running hours*
>> Ananlog inputs configurable as Binary or Tristate* >> Ananlog inputs configurable as Binary or Tristate*
>> Selectable Power-up default mode* >> Selectable Power-up default mode*
>> Dual AMF/Dual MRS function** >> Dual AMF/Dual MRS function**
>> Voltage unbalance protection** >> Current and Voltage unbalance protection
>> Direct communication with EFI engines >> Ananlog inputs configurable as Binary or
>> Total remote monitoring and control Tristate*
>> Easy to install, configure and use >> Selectable Power-up default mode*
>> Wide range of communication capabilities >> Dual AMF/Dual MRS function**
including: >> Voltage unbalance protection**
• connection via RS232, RS485, CAN or USB
• internet access using Ethernet
• support for Modbus RTU and TCP
>> Internal PLC support with PLC editor and PLC
monitor included in InteliConfig
>> Active SMS and emails in different languages
>> 2× 10 A binary outputs for cranking and fuel
solenoid
>> 4 analog inputs / 8 binary inputs / 8 binary
outputs on board
• Option for additional I/Os over modules
>> Flexible event based history with up to
350 events
>> Tier 4 final support
>> Activation of binary outputs based on
analog inputs
>> Comprehensive gen-set protections
>> Multipurpose flexible timers
>> True RMS measurement
>> Maintanance timers can count to negative*
Order code
>> Internal or ECU source for running hours*
IL3AMF20BAA >> Configurable main screen* *From firmware 1.6 **From firmware 1.7
>> Direct communication with EFI engines >> Multipurpose flexible timers
>> Total remote monitoring and control >> True RMS measurement
>> Cloud-based monitoring and control via >> Version for low temperature also available
WebSupervisor >> Maintanance timers can count to negative*
>> Geo-fencing and tracking via WebSupervisor >> Internal or ECU source for running hours*
>> Easy to install, configure and use >> Configurable main screen*
>> Wide range of communication capabilities >> Ananlog inputs configurable as Binary or
including: Tristate*
• connection via RS232, RS485, CAN or USB >> Selectable Power-up default mode*
• internet access using Ethernet, GPRS or 4G >> Dual AMF/Dual MRS function**
• support for Modbus and SNMP >> Voltage unbalance protection
protocols >> Current unbalance protection
>> Internal PLC support with PLC editor and PLC
monitor included in InteliConfig
>> Active SMS and emails in different languages
>> 2× 10 A binary outputs for cranking and fuel
solenoid
>> 4 analog inputs / 8 binary inputs / 8 binary
outputs on board
• Option for additional I/Os over modules
>> Flexible event based history with up to 350
events
>> Tier 4 final support
>> Load shedding and dummy load
>> Activation of binary outputs based
Order code
on analog inputs
IL3AMF25BAA >> Comprehensive gen-set protections *From firmware 1.6 **From firmware 1.7
>> Engine controller for telecom >> Smart battery cycling management for lower >> Smart battery charging and cycling
tower applications OPEX management for lower OPEX
>> Control, monitoring and protection for both >> WebSupervisor and AirGate support* >> Complete monitoring, control and
mechanical and electronic >> Automatic SMS on alarm or event & gen-set protection of the system
diesel/gas engines in one unit control over SMS* >> Uses variable or single speed DC
>> Automatic or manual start/stop >> On-line control and monitoring over web generators to charge batteries
of the engine pages (embedded web server) via plug & play >> WebSupervisor and AirGate support*
>> Programmable On/Off panel button IB-Lite >> Automatic SMS on alarm*
>> Support of engines with Electronic Control >> Optional GSM/GPRS modem/wireless >> Fuel measurement function
Unit (ECU) – J1939 or Cummins Modbus Internet via IL-NT GPRS >> Automatic Start and Stop according to the
>> Analog gauge (VDO, Datcon and others) >> Fuel theft protection and Total fuel accumulator voltage and charging current
outputs – operator friendly consumption monitoring >> Charging current/voltage regulated
>> Smooth engine speed control >> Air-conditioning control by speed (variable speed engines,
>> 7 configurable binary inputs >> Full gen-set monitoring and protection dual speed engines) or excitation
>> 7 configurable binary outputs >> Outstanding EFI engine support with (single speed engines)
>> 7 configurable analog inputs diagnostic messages in plain text via J1939 >> Voltage compensation according to
(3 resistive, 4 voltage) >> Detailed RTC event and performance log battery temperature
+ 2 not configurable voltage inputs >> Multiple languages (user changeable) in >> Charging time limitation and
>> Selectable protections alarm/shutdown controller, even more in installation suite other protection
>> 3 level of password protection >> Plug-in and CAN bus extension modules >> Circuit-breaker control
>> USB, RS485/RS232/Modem/Modbus capability >> Main screen layout adapted for
communication >> Earth fault current protection* DC applications
>> Automatic SMS on alarm >> A/B start battery support >> Service cycle allows the maintenance
>> On-line control and monitoring over >> Alternative switchable configuration people to trigger the charging manually
web pages >> Dual mutual stand-by (Dual AMF) support >> ComAp SCADA compatible
(embedded web server) via IB-Lite >> History log
>> Optional GSM/GPRS modem/wireless
Internet via IL-NT GPRS
Gen-set
Events Datacentres
controllers:
Parallel
Mining Hospitals
ComAp’s gen-set paralleling controllers allow users to have multiple generators running at the
same time, and ensure that they are all running at optimum efficiency. Whether you are running
an emergency back-up system, running multiple generators in sync with the mains grid, or using
different sizes and models of generators in a single installation, ComAp has a product that will
provide you with the control you require.
21
InteliGen 200
New Generation of
Parallel Gen-set Controller
>> Synchronising - Optimize your gen-set usage >> Total remote monitoring and control
or parallel different sizes and brands of >> InteliConfig for configuration and monitoring
generators >> WinScope for precise tuning of PID regulators
>> PLC - Utilise our unique, and easy to use PLC exactly according to gen-set type and
drag-and-drop blocks for configuration. application needs
>> New design - Flexibility to change the >> WebSupervisor for cloud based monitoring
application e.g. SPtM and MINT. and control of your whole gen-set fleet
>> Built in AVRi - You no longer need a separate >> Wide range of communication and
AVRi interface in your installation. connection capabilities including:
>> Plug-in modules - Customize your >> USB, CAN and RS485 on board
controller with our plug-in extension and >> USB master for configuration or firmware
communication modules. upload or download
>> 4G/LTE - Connect to your gen-set via 4G/LTE >> RS232 and additional RS485 via plug-in
for alerts or use ComAp‘s WebSupervisor. module
>> GPS - Always know the location of your gen- >> internet access using Ethernet, GPRS/3G/4G
set using geofencing for theft or movement via plug-in modules
alerts. >> configurable Modbus RTU or TCP and
>> InteliConfig - Our new configuration and support of SNMP protocols v1 or v2c
monitoring PC tool (based on new LiteEdit) will >> Internal PLC support with PLC editor and
offer you multi gen-set control and monitoring monitor included in InteliConfig
as well as easy set-up. >> Active SMS and emails in different languages
>> Easy switching between parallel to mains or >> Geofencing and tracking via WebSupervisor
multiple genset applications >> 2 x high current binary outputs for cranking
>> Phase Match, Slip Synchro or Droop and fuel solenoid, powered by separated
synchronisation E-Stop input
Order code
>> Direct communication with EFI engines
IG3200XXBAA including Tier 4 Final support
Some features require the use of additional
expansion or communication cards.
>> Synchronising - Optimize your gen-set usage >> Multiple gensets in parallel to mains available >> internet access using Ethernet, GPRS/3G/4G
or parallel different sizes and brands of together with InteliMains 210 controller via plug-in modules
generators >> Multiple gensets and grids in parallel available >> configurable Modbus RTU or TCP and
>> PLC - Utilise our unique, and easy to use PLC together with the Mains and BTB controllers. support of SNMP protocols v1
drag-and-drop blocks for configuration. >> Two types of synchronisations: Phase Match >> Internal PLC support with PLC editor and
>> New design - Flexibility to change the or Slip Synchro monitor included in InteliConfig
application e.g. SPtM and MINT. >> Two types of Load/VAr Sharing: Isochronous >> Active SMS and emails in different languages
>> Built in AVRi - You no longer need a separate (CAN) or Droop, including Emergency Droop >> Geofencing and tracking via WebSupervisor
AVRi interface in your installation. >> Direct communication with EFI engines >> 2 x 10 A binary outputs for cranking and fuel
>> Plug-in modules - Customize your including Tier 4 Final support solenoid, powered by separated E-Stop input
controller with our plug-in extension and >> Total remote monitoring and control >> Option for additional inputs/outputs
communication modules. >> InteliConfig for configuration and monitoring >> Flexible event based history with up to 350
>> 4G/LTE - Connect to your gen-set >> WinScope for precise tuning of PID events
via 4G/LTE for alerts or use ComAp‘s regulators exactly according to gen-set type >> Load shedding, dummy load capability
WebSupervisor. and application needs >> Comprehensive gen-set protections
>> GPS - Always know the location of your gen- >> WebSupervisor for cloud based monitoring >> Multipurpose flexible timers
set using geofencing for theft or movement and control of your whole gen-set fleet >> UL listed
alerts. >> Wide range of communication and
>> InteliConfig - Our new configuration and connection capabilities including:
monitoring PC tool (based on new LiteEdit) >> USB, CAN and RS485 on board
will offer you multi gen-set control and >> USB master for configuration or firmware
monitoring as well as easy set-up. upload or download
>> Easy switching between parallel to mains or >> RS232 and additional RS485 via plug-in
multiple genset applications module
Order code
>> The InteliGen NTC, an enhanced version of >> Inputs and outputs configurable for various
ComAp’s besteller – InteliGenNT, is a high-end customer needs
controller suitable for any complex single >> Controller redundancy
or multiple gen-sets paralleling application >> Event-based history (up to 500 records) with
operating in standby or island mode. It is a customer-selectable list of stored values; RTC;
perfect unit for mission-critical installations statistic values
such as datacenters, power stations or rental >> Integrated PLC programmable functions
applications >> Integrated fixed and configurable protections
>> InteliGen NTC features ComAp’s powerful >> Selectable measurement ranges for AC
in-built PLC delivering high-level of flexibility, voltages and currents – 120 / 277 V,
advanced history log and fully configurable 0–1 / 0–5 A
protections. >> Secondary isolated RS232 / RS485 interface
>> Gen-set controller for single or multiple >> Support of external colour displays
generating sets operating in standby or >> USB 2.0 slave interface
parallel modes
>> Support of engines with ECU
(Electronic Control Unit)
>> Many communication options – full and
intuitive remote supervising and servicing
>> Gen-set performance log for intuitive and fast
problem tracking
>> Automatic synchronizing and power control
(via speed governor or ECU)
>> AMF function, Baseload, Import / Export,
Peak shaving, Voltage and PF control (AVR)
Order code
>> Generator measurement,
IG-NTC GC Mains measurement
>> InteliGenNTC BaseBox is a comprehensive Peak shaving, Voltage and PF control (AVR)
gen-set controller for both single and multiple >> Generator measurement: U, I, Hz, kW, kVAr,
gen-sets operating in standby or paralleling kVA, PF, kWh, kVAhr
modes. The detachable modular construction >> Mains measurement: U, I, Hz, kW, kVAr, PF
allows fast and intuitive installation with >> Selectable measurement ranges for
the potential for many different extension AC voltages and currents – 120 / 277 V,
modules designed to suit individual customer 0–1 / 0–5 A
requirements. >> Inputs and outputs configurable for various
>> To be used in conjunction with colour displays customer needs
InteliVision 5 or InteliVision 8 >> Bipolar binary outputs – possibility to use BO
>> Support of engines with ECU as High or Low side switch
(Electronic Control Unit) >> Controller redundancy
>> Complete integrated gen-set solution and >> Event-based history (up to 1000 records) with
signal sharing via CAN bus – minimum customer-selectable list of stored values;
external components needed RTC; statistic values
>> Many communication options – full and >> Integrated PLC programmable functions
intuitive remote supervising and servicing >> Integrated fixed and configurable protections
>> AirGate support, Ethernet connection >> DIN-Rail mount
(RJ45), USB 2.0 slave interface, 1× RS232 / >> Customized firmware solution
2× RS485 interface with Modbus protocol
support; Analog / GSM / ISDN / CDMA
modem communication support; SMS
messages; ECU Modbus interface; secondary
RS485 converter is isolated
>> Automatic synchronizing and power control
Order code
(via speed governor or ECU)
IG-NTC-BB >> AMF function, Baseload, Import / Export,
>> Premium gen-set controller for both single >> Plug & Play Local and Remote monitoring
and multiple gen-sets operating in standby or from a range of ComAp HMI display units and
parallel modes. dedicated PC tools or Web based services,
>> Support of complex applications for power including the AirGate technology, offers you
production in data centres, hospitals, banks an full, intuitive and secure monitoring of the
and and smaller CHPs controlled fleet, site or technology.
>> Support of engines both with electronic >> Force value function allows to use alternative
unit – ECU and mechanical engines. configuration setting based on actual
>> Complete control of the engine, alternator condition, allows better control of the gen-set
and controlled technology from one unit, or related technology based on its actual
including synchronisation, provides access situation.
to all measured data in a coherent and time >> All analogue and binary I/Os are freely
corresponding way. configurable to suit every application
>> Wide range of communication interfaces requirement, and to use just the right amount
allows smooth integration into local monitoring of I/Os or I/O expansion modules which saves
systems (BMS, etc.) customer costs.
>> Internal built-in PLC interpreter allows you
to configure customised logic to meet
demanding customer requirements on your
own without extra programming knowledge
and in a fast way.
>> Configurable event-based history (up to
4000 records) with extra Pre-mortem part
is a valuable tool for troubleshooting and
performance analysis.
Order code
IS-NTC-BB
Gen-set controllers Parallel 27
InteliSys GSC-C
Premium Paralleling Gen-set Controller,
compliant to the latest EU Grid codes
>> Premium gen-set controller for both single >> Configurable event-based history (up to
and multiple gen-sets operating in standby or 4000 records) with extra Pre-mortem part
parallel modes. is a valuable tool for troubleshooting and
>> Compliant to the European Requirements performance analysis.
for Generators, and VDE-AR-N 4105:2018, >> Plug & Play Local and Remote monitoring
VDE-AR-N 4110:2018, including Single Fault from a range of ComAp HMI display units and
Tolerance dedicated PC tools or Web-based services,
>> Support of complex applications for power including the AirGate technology, offers you
production in data centres, hospitals, banks an full, intuitive and secure monitoring of the
and smaller CHPs controlled fleet, site or technology.
>> Support of engines both with electronic >> Force value function allows to use alternative
unit – ECU and mechanical engines. configuration setting based on actual
>> Complete control of the engine, alternator condition, allows better control of the gen-set
and controlled technology from one unit, or related technology based on its actual
including synchronisation, provides access situation.
to all measured data in a coherent and time >> All analogue and binary I/Os are freely
corresponding way. configurable to suit every application
>> Wide range of communication interfaces requirement, and to use just the right amount
allows smooth integration into local monitoring of I/Os or I/O expansion modules which saves
systems (BMS, etc.) customer costs.
>> Internal built-in PLC interpreter allows you >> Compliant to the European Requirements
to configure customised logic to meet for Generators, and VDE-AR-N 4105:2018,
demanding customer requirements on your VDE-AR-N 4110:2018, including Single
own without extra programming knowledge Fault Tolerance
and in a fast way.
Order code
IS2GSCCXBAB
28 Gen-set controllers Parallel
InteliMains 210
New Generation of Mains
Supervision Controller
>> Synchronising - for multiple up to 31 gen-sets >> WinScope for precise tuning of PID
operating in parallel to mains regulators exactly according to gen-set
>> Compliant to the European Requirements for type and application needs
Generators, and VDE-AR-N 4105:2018, VDE- >> WebSupervisor for cloud based monitoring
AR-N 4110:2018 and control of your whole gen-set fleet
>> PLC - Utilise our unique, and easy to use PLC >> Wide range of communication and
drag-and-drop blocks for configuration. connection capabilities including:
>> New design - Flexibility to change the >> USB, CAN and RS485 on board
application e.g. MCB & MGCB. >> USB master for configuration or firmware
>> Plug-in modules - Customize your upload or download
controller with our plug-in extension and >> RS232 and additional RS485 via plug-in
communication modules. module
>> 4G/LTE - Connect to your gen-set via 4G/LTE >> internet access using Ethernet,
for alerts or use ComAp‘s WebSupervisor. GPRS/3G/4G via plug-in modules
>> GPS - Always know the location of your gen- >> configurable Modbus RTU or TCP and
set using geofencing for theft or movement support of SNMP protocols v1 or v2c
alerts. >> Internal PLC support with PLC editor and
>> InteliConfig - Our new configuration and monitor included in InteliConfig
monitoring PC tool will offer you multi gen-set >> Active SMS and emails in different
control and monitoring as well as easy set-up. languages
>> Two types of synchronisations: Phase >> Geofencing and tracking via
Match or Slip Synchro WebSupervisor
>> Multiple grids (e.g. H-diagram) support >> Option for additional inputs/outputs
together with the Bus Tie Breaker >> Flexible event based history with up to 350
controller(s) events
Order code
>> Total remote monitoring and control >> Multipurpose flexible timers
IM3210XXBAA >> InteliConfig for configuration and monitoring >> UL listed certification
Order code
IM-NT GC
30 Gen-set controllers Parallel
InteliMainsNTC BaseBox
Mains Protection and Supervision
Controller, compliant to the latest
EU Grid codes
>> For multiple up to 31 gen-sets operating in >> Allows to build complex applications with >> Many communication options – full and
parallel to mains (or isolated parallel) more mains incomers, bus-tie breakers, and intuitive remote supervising and servicing:
>> Compliant to the European Requirements for load management • 1× RS232 / 1× RS485 interface with
Generators, and VDE-AR-N 4105:2018, VDE- >> AMF function, Peak shaving Modbus protocol support
AR-N 4110:2018 >> Mains measurement: U, I, Hz, kW, kVAr, kVA, • Analog / GSM / ISDN / CDMA modem
>> To be used in conjunction with colour PF, kWh, kVAhr communication support
displays InteliVision 5, InteliVision 5 RD or >> Bus measurement: U, Hz (kW, kVAr, PF – via • SMS messages
InteliVision 8 CAN from gen-set group) • RS485 converter is isolated
>> Many different power control modes available >> Selectable measurement ranges for (one RS485 Display-dedicated port)
>> System Baseload with limited export or AC voltages and currents – 120 / 277 V, • AirGate support
minimal import 0–1 / 0–5 A • Ethernet connection (RJ45)
>> Import/Export power control of gen-set >> Inputs and outputs configurable for various • USB 2.0 slave interface
group customer needs: >> Controller redundancy
>> Temperature of the system by power control • 12 Binary Inputs >> Event-based history (up to 1000 records)
>> Dynamic changes of required system power • 12 Binary Outputs with customer-selectable list of stored values
via analog input • 3 Analog Inputs >> RTC
>> Reverse synchronization of the loaded • 1 Analog Output
gen-set group to mains >> Bipolar binary outputs – possibility to use BO
>> Forward synchronization of Mains as High or Low side switch
to gen-set group
>> Coupling of several synchronized mains to
a common bus
Order code
IM-NTC-BB
Gen-set controllers Parallel 31
InteliSys Gas InteliSysNTC Hybrid
Controller for Gas Gen-set PV-Diesel hybrid system controller
Applications compliant to the latest
EU Grid codes
>> The InteliSys Gas is an industrial grade controller for gas engine >> InteliSysNTC Hybrid is a standalone controller for PV-Diesel hybrid applications
generator sets mainly used in CHP (Cogeneration) and power generation that combine reciprocating gen-sets with renewable sources of power. It is
applications. The InteliSys Gas controls, monitors and protects the suitable for off-grid (microgrids) as well as on-grid installations.
generator set according defined setpoints and its configuration. >> Continuous monitoring and control of all sources of energy including
>> Compliant to the European Requirements for Generators, and VDE-AR-N solar, wind, hydro, energy storage and gen-sets
4105:2018, VDE-AR-N 4110:2018, including Single Fault Tolerance >> Interface to PV inverters via Modbus RTU or TCP*
>> Preconfigured functions, scalable and configurable I/Os, broad >> Interface to ComAp InteliGen and InteliSys gen-set controllers** via CAN
communication capabilities a fast and intuitive allows to adapt the >> Optimized system efficiency by minimizing the necessary dynamic
controller to various applications without greater efforts. spinning reserve while keeping reliability during the PV output drops;
>> The InteliSys Gas and its accessories gives you the perfect solution for the InteliSysNTC Hybrid controller calculates and distributes the dynamic
your gas engine generator set application. spinning reserve to the gen-set controllers
>> Predefined adjustable functions tailored to gas engine specific needs. >> Extensive flexibility due to built-in PLC to cover complex sites control and
>> Read in of all relevant mechanical and electrical signals via Sensors, various operating scenarios
Voltage and Current Transformers to control the entire generator set. >> Synchronization of gen-sets with the mains and export/import limitation
>> Full control of the circuit breakers like Generator Breaker and control to fulfill the utilities needs in on-grid application
Mains Breaker. >> AirGate connection and WebSupervisor offer remote monitoring and full
>> Automatic Synchronization and kW/kVAr Control to safely connect your control of the whole site
generator to the bus and run in stable operation. >> Data acquisition from all power sources provides detailed statistics about
>> Baseload control, Peak Shaving, Import & Export Power Control to and energy yield in selected interval (day, week, month) and gen-set fuel
from the grid e.g. to keep the Electrical Power within the limits as agreed consumption
with the distribution system operator (DSO).
>> Marine certified gen-set >> Gen-set controller for both single >> Mains supervision controller >> Marine Certified premium
controller for single or multiple and multiple gen-sets operating base unit gen-set controller for both single
generating sets operating in in standby or paralleling modes >> Many different power control and multiple gen-sets operating
standby or parallel modes >> Support of engines with ECU modes available: in standby or parallel modes
>> Approved by DNV, GL, LR and (Electronic Control Unit) • System Baseload with limited >> Support of cogeneration (CHP)
CRS Registers >> Complete integrated gen-set export or minimal import and other complex applications
>> Support of engines with ECU solution and signal sharing via • Import/Export power control >> To be used in conjunction with
(Electronic Control Unit) CAN bus – minimum external of gen-set group colour displays InteliVision 8
>> Many communication options components needed • Temperature of the system or InteliVision 5
– full and intuitive remote >> Many communication options by power control >> Support of engines with ECU
supervising and servicing – full and intuitive remote • Dynamic changes of required (Electronic Control Unit)
>> Gen-set performance log for supervising and servicing system power via analog input >> Complete integrated gen-set
easy problem tracing • AirGate support, Ethernet >> Reverse synchronization of the solution and signal sharing via
>> Automatic synchronizing and connection (RJ45), USB 2.0 loaded gen-set group to mains CAN bus – minimum external
power control (via speed slave interface, 1× RS232 / >> Forward synchronization of components needed
governor or ECU) 2× RS485 interface Mains to gen-set group >> Many communication options –
>> AMF function, Baseload, Import with Modbus protocol >> Coupling of several synchronized full and intuitive remote
/ Export, Peak shaving, Voltage support; Analog / GSM mains to a common bus supervising and servicing
and PF control (AVR) / ISDN / CDMA modem >> Allows to build complex >> Gen-set performance log for
>> Generator measurement, Mains communication support; applications with more mains easy problem tracing
measurement SMS messages; ECU incomers, bus-tie breakers, and >> Automatic synchronizing and
Modbus interface; secondary load management power control (via speed
RS485 converter is isolated governor or ECU)
Generator
Telecom Marine
and ATS
controllers
Datacenters Mining
GeCon controllers provide comprehensive generator protection and control for single or
multiple gen-sets based on field proven InteliGenNT and InteliSysNT platforms. The primary
function of the generator controller is to manage and protect the generator in preference
to the engine, which is not a direct concern.
35
InteliGen NTC GeCon InteliGenNT Marine GeCon
Complex Parallel Generator Controller High-End Marine Certified Generator
Controller
>> Gen-set controller for single or multiple generating sets operating >> Marine certified generator controller for single or multiple generating
in standby or parallel modes sets operating in standby or parallel modes
>> Support of engines with ECU (Electronic Control Unit) >> Many communication options – full and intuitive remote supervising
>> Many communication options – full and intuitive remote supervising and servicing
and servicing >> Generator performance log for easy problem tracing
>> Gen-set performance log for easy problem tracing >> Automatic synchronizing and control breaker
>> Automatic synchronizing and power control (via speed governor >> AMF function, Baseload, Import / Export, Peak shaving, Voltage and
or ECU) PF control (AVR)
>> AMF function, Baseload, Import / Export, Peak shaving, Voltage >> Generator measurement, Mains measurement
and PF control (AVR) >> Inputs and outputs configurable for various customer needs
>> Generator measurement, Mains measurement >> Controller redundancy
>> Inputs and outputs configurable for various customer needs >> Event-based history (up to 500 records) with customer-selectable list
>> Controller redundancy of stored values; RTC; statistic values
>> Event-based history (up to 500 records) with customer-selectable >> Integrated PLC programmable functions
list of stored values; RTC; statistic values >> Integrated fixed and configurable protections
>> Integrated PLC programmable functions >> Marine approved by DNV, GL, Lloyd´s Register and CRS
>> Integrated fixed and configurable protections
>> Comprehensive generator controller for both single and multiple gen- >> Premium generator controller for both single and multiple gen-sets
sets operating in standby or paralleling modes operating in standby or parallel modes
>> To be used in conjunction with colour displays >> Support of cogeneration (CHP) and other complex applications
InteliVision 5 or InteliVision 8 >> To be used in conjunction with colour displays
>> Complete integrated gen-set solution and signal sharing InteliVision 8 or InteliVision 5
via CAN bus – minimum external components needed >> Complete integrated generator solution and signal sharing via CAN
>> Many communication options – full and intuitive remote supervising bus – minimum external components needed
and servicing >> Many communication options – full and intuitive remote supervising
>> Generator performance log for fast and time-saving problem tracing and servicing
>> Automatic synchronizing and control breaker >> Generator performance log for fast and time-saving problem tracing
>> AMF function, Baseload, Import / Export, Peak shaving, Voltage >> Automatic synchronizing and control breaker
and PF control (AVR) >> Baseload, Import / Export, TempByPower, Peak shaving, Voltage
>> Generator measurement: U, I, Hz, kW, kVAr, kVA, PF, kWh, kVAhr and PF control (AVR)
>> Mains measurement: U, I, Hz, kW, kVAr, PF >> Generator measurement: U, I, Hz, kW, kVAr, kVA, PF, kWh, kVAhr
>> Selectable measurement ranges for AC voltages >> Mains measurement: U, I, Hz, kW, kVAr, PF
and currents – 120 / 277 V, 0–1 / 0–5 A >> Selectable measurement ranges for AC voltages
>> Inputs and outputs configurable for various customer needs and currents – 120 / 277 V, 0–1 / 0–5 A
>> Bipolar binary outputs – possibility to use BO as High or Low side switch >> Inputs and outputs configurable for various customer needs
>> 1× RS232 / 2× RS485 interface with Modbus protocol support; >> Bipolar binary output – possibility to use BO as High or Low side switch
Analog / GSM / ISDN / CDMA modem communication support; >> 1× RS232 / 2× RS485 interface with Modbus protocol support;
SMS messages; secondary RS485 converter is isolated Analog / GSM / ISDN / CDMA modem communication support;
>> AirGate support SMS messages; secondary RS485 converter is isolated
IG-NTC BB IS-NTC BB
Generator and ATS controllers Generator controllers 37
InteliATSNT STD InteliATSNT PWR
Automatic Transfer Switch Automatic Transfer Switch
(ATS) Controller (ATS) Controller
>> Mains monitoring (1 or 3 phases) for under and over voltage, >> Mains monitoring (1 or 3 phases) for under and over voltage,
under and over frequency and voltage unbalance under and over frequency and voltage unbalance
>> Remote generating set start >> Remote generating set start
>> Change over for mains and generator contactors >> Change over for mains and generator contactors
>> True voltage and current RMS measurement >> True voltage and current RMS measurement
>> Simple Test Run scheduler >> Test Run scheduler
>> 2 languages (user changeable) >> 3 phase power measurement
>> 4 binary inputs >> Detailed RTC event and performance log
>> 4 binary outputs >> WebSupervisor and AirGate support*
>> UL Recognised >> 2 languages (user changeable)
>> IEC 60947-6-1 compliant >> 7 binary inputs
>> 7 binary outputs
>> UL listed
>> IEC 60947-6-1 compliant
protections
Hybrid Telecom
A family of mains protection modules that provide the necessary protection functions to meet
the requirements of all applications where generators operate in parallel with the mains.
* Plug-in module required
39
InteliPro InteliPro SYNC MainsPro MainsPro LITE
Utility Protection Relay Synchronization and Mains Decoupling Relay Mains Decoupling Relay
Protection Relay
>> InteliPro is a highly flexible >> InteliPro SYNC is a highly >> MainsPro is a protection >> MainsPro LITE combines simple
mains decoupling relay with reliable protection relay relay for parallel-to-mains installation and usability with
extensive range of protective designed for synchronization in applications including generator valuable mains protection
functions to meet the strictest parallel to mains applications, sets, cogeneration units, micro >> True RMS measurement for
utility interconnection such as generators, gen-sets turbines or renewable energy increased accuracy and reliable
requirements. It can be and cogeneration units sources such as photovoltaic evaluation of failures
used in various distributed connected to distribution plants or wind turbines. It >> Compact design for installation
generation applications, next to network. InteliPro SYNC is an provides adjustable voltage, in restricted spaces
cogeneration units, renewable ideal substitute for manual frequency and loss of mains >> Suitable for low voltage
energy sources or as a back-up synchronizing relay. protections to safeguard both installations
protection for gen-sets >> Synch check, over/ the distribution network and the >> Simple wiring with detachable
>> Extensive frequency, voltage undervoltage and reverse generators. connectors
and current protections power protection in one unit >> User friendly interface with easy >> Two-stage over/under voltage
>> Optional features enable to >> Over/underfrequency, settings (no SW tool needed) protection
meet particular requirements of Instantaneous overcurrent, >> Simple wiring with detachable >> Two-stage over/under
utilities IDMT overcurrent and Earth connectors frequency protection
>> Compliant with G59/3, G10, Fault protection as optional >> Integrated mechanical lock, >> Floating average overvoltage
G83, IEEE 1547 and features history track and watchdog protection
VDE-AR-N 4105 >> Extensive flexibility for various protection >> Phase supervision
>> Certified according to applications through set of >> Compliant with G59/3, >> Freely assignable variety of
IEC 60255, VDE 0126-1-1 optional functions G83, UL508 binary inputs and outputs
and BDEW >> Certified according to >> Event history log
>> Applicable for requirements of IEC 60255, CEI 0-21, >> Auto fault reset
G59/3, G10, G83 and IEEE1547 IEn NR 005/2012, >> CB Failure protection
and VDE-AR-N 4105 VDE V 0126-1-1 and
VDE-AR-N 4105
40 Mains protections
Suitable for:
controllers
Marine Telecom
The ComAp family of engine controllers offers innovative and universal system integration
for a wide range of engine driven platforms and applications. With a proven track record
of working in the most demanding environments, InteliDrive controllers deliver unparalleled
command, control and communication advantages.
41
InteliDrive WP
Engine Controller with
a small form factor
42 Engine controllers
InteliDrive IPU InteliDrive IPC
Industrial Power Unit Controller Irrigation Pump Controller
>> Engine controller for land-based and marine Tier 4 applications >> Engine and pump controller for land-based and marine
>> Control, monitoring and protection for both mechanical and electronic Tier 4 applications
diesel/gas engines in one unit >> Control, monitoring and protection for both mechanical and electronic
>> Automatic, manual or remote start/stop of the engine diesel/gas engines in one unit
>> Support of engines with Electronic Control Unit (ECU) – J1939 >> Automatic, manual or remote start/stop of the engine
or Cummins Modbus >> Support of engines with Electronic Control Unit (ECU) – J1939
>> Analog oil pressure, water temperature, fuel level, battery voltage, or Cummins Modbus
engine speed (pick-up) >> Analog oil pressure, water temperature, fuel level, battery voltage,
>> Smooth engine speed control by Up/Down controller buttons, binary engine speed (pick-up)
inputs for predefined speed options, Speed Up/Down binary inputs >> Smooth engine speed control by Up/Down controller buttons, binary
or one analog input inputs for predefined speed options, Speed Up/Down binary inputs or
>> Selectable protections alarm/shutdown one analog input
>> 3 levels of password protection >> Pump functionalities: flow meter, flow switch, set of flexible timers
>> Ethernet, USB, GSM/GPRS, RS485 or RS232/Modem/Modbus >> Selectable protections alarm/shutdown
communication >> 3 levels of password protection
>> Automatic SMS on alarm >> Ethernet, USB, GSM/GPRS, RS485 or RS232/Modem/Modbus
>> On-line control and monitoring over web pages communication
(embedded web server) >> Automatic SMS on alarm
>> 2 languages (user changeable) >> On-line control and monitoring over web pages
>> Real time clock and event history log (embedded web server)
>> Push buttons for simple control, lamp test >> 2 languages (user changeable)
>> Front panel sealed to IP65 >> Real time clock and event history log
>> Front panel sealed to IP65
ID2IPUXXBAA ID2IPCXXBAA
Engine controllers 43
InteliDrive Lite
Engine Controller for Pumps
and Compressors
>> Engine controller for land-based and marine >> Selectable protections alarm/shutdown
Tier4 applications >> 3 level of password protection
>> Control, monitoring and protection for >> USB, RS485/RS232/Modem/Modbus
both mechanical and electronic diesel/gas communication
engines in one unit >> Automatic SMS on alarm
>> Automatic or manual start/stop >> On-line control and monitoring over web
of the engine pages (embedded web server) via IB-Lite
>> Programmable On/Off panel button >> Optional GSM/GPRS modem/wireless
>> Support of engines with Electronic Control Internet via IL-NT GPRS
Unit (ECU) – J1939 or Cummins Modbus >> AirGate support
>> Analog gauge (VDO, Datcon and others) >> 2 languages (user changeable)
outputs – operator friendly >> Real time clock and event history log
>> Smooth engine speed control >> PLC functions: PID loop, Comparators,
>> 7 configurable binary inputs Timers
>> 7 configurable binary outputs >> Push buttons for simple control, lamp test
>> 7 configurable analog inputs >> Front panel sealed to IP65
(3 resistive, 4 voltage) + 2 not configurable >> EN, UL certifications
voltage inputs
Order code
ID-FLX-LITE
44 Engine controllers
InteliDrive Lite EM InteliDrive Lite FPC
Engine Controller for Electric Engine Controller Designed for Diesel
Asynchronous Motors Driven Fire Pump Applications
>> Electric Motor control, monitoring and protection >> Modular engine controller designed for diesel driven fire pump
>> All common ways to start asynchronous motor: direct, Y-D, applications based on the NFPA 20 standard
SoftStarter starting >> Automatic and manual starting sequence based on two batteries
>> 7 configurable binary inputs and outputs according to NFPA 20 standard
>> 3 configurable analog inputs >> Support of engines equipped with Electronic Control Unit
>> Selectable protections alarm/shutdown (ECU) – J1939 or Cummins Modbus interface
>> Setpoints adjustable via keyboard or PC >> Analog gauge (VDO, Datcon) outputs – operator friendly
>> USB, RS485 or RS232, GSM/GPRS, ModBus communication >> Engine speed control
>> Real time clock and event history log >> 3 configurable analog inputs + 2 analog inputs of battery voltage
>> Automatic or manual start/stop of the motor measurement
>> Push buttons for simple control, lamp test >> 7 configurable binary inputs and outputs
>> Graphic back-lit LCD display 128 × 64 pixels >> 6 LED indicators (Alarm, Warning, Not Ready, Running,
>> LED indicators Battery A, Battery B)
>> Front panel sealed to IP65 >> Selectable protections alarm/shutdown
>> Power supply 8–36 VDC >> 1 level of password protection
>> 3 phase protections >> USB, RS485/RS232/Modem/Modbus communication
>> Automatic SMS on alarm
>> On-line control and monitoring over web pages
(embedded web server) via IB-Lite
>> 2 languages (user changeable)
>> Real time clock and event history log
Order code
ID-DCU
46 Engine controllers
InteliDrive DCU Marine InteliDrive Marine
Modular Certified Engine Controller Engine controller for
for Marine Applications Marine Applications
>> Modular IACS certified engine controller for marine applications >> Engine controller for marine Tier4 Final propulsion applications
>> Control, monitoring and protection for any type of marine engines >> Control, monitoring and protection for any type of marine engine
>> Dedicated Emergency, Auxiliary, Harbour and Propulsion engines >> Support of EFI (ECU) engines via CAN/J1939 or Cummins Modbus
application >> Redundant architecture by using backup redundant protection unit
>> Single speed application for generators and variable speed application Inteli RPU
for propulsion, pumps, compressors >> Support of two independent power supplies via I-RPU module
>> Support of wide range of EFI (ECU) engines with Tier 4F support >> 7 configurable binary inputs, 7 configurable binary outputs
>> Support of multi CANbus devices >> 9 configurable analogue inputs
>> Connection to engine via primary J1939 and backup J1587 buses or (3 resistive, 3 current 0-20mA, 3 voltage 0-10V)
Cummins Modbus >> Option for additional inputs/outputs
>> Remote monitoring via Modbus, Ethernet and AirGate >> Selectable protections warning/cooling down/shutdown
>> Configurable Modbus RTU and Modbus TCP >> 3 level of controller setting / operation password protection
>> RS232, RS485, Ethernet communication support >> Ethernet, USB, GSM / GPRS, RS485 or
>> WebSupervisor support for remote supervising and monitoring RS232 / Modem / Modbus communication
>> Redundant architecture: Main unit + Backup module >> Automatic SMS on alarm
>> Backup ID-RPU module with broken wire protections >> On-line control and monitoring over web pages
>> Speed/load control via J1939 or J1587 buses (embedded web server)
>> Symmetrical load sharing for propulsion engines with J1939 (via CAN bus) >> Real time clock and event history log
>> Power management controller cooperation over CAN bus (IG/IS-NTC-BB) >> Toggle button with additional features adjustments
>> Integrated clutch control >> Up/Down speed regulation buttons on the front facia
>> 14 binary inputs, 14 binary outputs, 8 analog inputs >> 2 languages (user changeable), Chinese language support
>> Marine certified extension modules for expandable number >> Front panel sealed to IP65
of Input/Outputs
>> 80× AIN, 32× AOUT, 112× BIN, 112× BOUT
>> Diesel/gas engine control, monitoring and protection for off-road >> Data logger – outstanding, monitoring and history tracking for diesel
applications such as construction, quarrying and engineering engines as well as peripheral equipment
equipment >> Plug and play support of engines with ECU – access to all
>> Control of hydraulic systems and engine driven compressors available values
and pumps >> Built-in Event & Performance Log
>> Designed for harsh environments – the unit construction features a >> Remote monitoring support
fully environmentally sealed enclosure and connector >> Fleet management program with GSM/GPS localization
>> Plug & Play EFI (ECU) engine support (CAN/J1939) and Geofencing
>> Master Slave Concept Support >> History log out
>> Remote monitoring support >> Engine measurement by sensors and actuators or via J1939
>> Fleet management via GPRS/GPS, GeoFencing >> 8 Binary inputs
>> Integrated PLC functions: Analog switches, Comparators with delay or >> 11 Configurable analog inputs
hysteresis, Counters, Delay functions, Filters, Linear interpolation, Logical >> 1× Frequency input for RPM measurement
and Mathematical functions, PID loops, Timers >> 2× Impulse inputs
>> Built-in event & Performance Log >> LED status indication
>> History log out – monitoring of wide range of parameters >> Communication Interface RS485, 2× CAN, J1939
>> 4 Binary inputs with detection of broken wire >> Possibility to connect with external displays
>> 12 Binary bi-directional inputs for contacts switching >> Running-hours meter, number of starts counter,
>> 8 Binary configurable switches (High-side/Low-side 3A, PWM 3A, battery voltage measurement
DC motor driver) >> Integral fuel consumption measuring
>> 8 Binary Hi-side switches with max. current 3A and detection
of broken wire
products
Trucks Oil & Gas
ComAp, a market leader in engine control solutions, have developed an easy to fit bi-fuel
management package including a range of InteliBifuel controllers for use as a standard control
platform for diesel generators. The new control system is ideally suited to generator packagers
and original equipment manufacturers (OEMs) looking to deliver more economically beneficial
power packages.
49
InteliBifuel LITE InteliBifuel
Bi-fuel/dual fuel control system Bi-fuel/dual fuel control system
for low-powered engines for single speed engines
>> InteliBifuel LITE package is a cost effective, compact solution >> InteliBifuel package is a fully programmable solution designed for any
designed for single speed Bi-fuel applications at nominal output single speed Bi-fuel application, with its features perfectly suitable for
power up to 100 or 500kW. Oil & Gas, Mining and Rental applications
>> Perfectly suitable for the Rental market or any other Power generation >> New algorithm with automatic compensation for gas quality changes
applications using any type of gas >> Enable factory setting of Bi-fuel system
>> High or low pressure single point gas injection technology, gas >> Simplified installation and commissioning
injected before or after the turbocharger >> Extended PLC logic and history
>> NEW algorithm with automatic compensation for gas quality changes >> Optional GPRS/GMS and GPS monitoring
>> Easy installation and commissioning >> IP-69 enclosure fits to any application
>> Harsh environmental design >> Optional high pressure single point gas injection after turbocharger
>> IP-69 enclosure fits to any application >> Compatible with InteliVision 5, and InteliVision 8 displays
>> Compatible with InteliVision 5, and InteliVision 8 displays
IB2SL5XCBDK IB2SGXDCBDK
50 Bi-fuel products
InteliBifuel MOBILE InteliBifuel DENOX
Bi-fuel/dual fuel control system Bi-fuel anti-knocking device
for mobile variable speed engines
>> InteliBifuel MOBILE package is a fully programmable solution >> Unique anti knocking engine protection controller specifically
designed for any mobile variable speed applications as Mine haul designed for Bi-fuel applications, ensure proper detonation is always
trucks, Frack trucks, Locomotives or Marine propulsion engines. maintained during Bi-fuel operation.
>> Fully configurable 3D maps >> Suitable for engines up to 20 cylinders
>> IP-69 Harsh environmental design allows full integration in applications >> Suitable for variable speed engines
with limited space >> Individual cylinder knocking detection
>> Remote monitoring >> Individual cylinder misfiring detection
>> GPRS/GSM remote monitoring >> Integrated 2× Inteli AIN8TC up to 16 thermocouples
>> GPS Location >> Harsh environmental design IP69K
>> Extended PLC logic >> Full communication and direct CAN interface to InteliBifuel LITE,
>> Extensive history records InteliBifuel and InteliBifuel MOBILE
>> Optional high or low pressure single point gas injection technology; >> Operating temperature: -40°C to +80°C > CE, UL, CSA
gas injected before or after the turbocharger
>> Compatible with InteliVision displays
>> Assembly of components necessary to reduce and control gas flow into the engine.
>> Suitable for High Speed engine Conversions
>> Ended with electronic throttle valve
>> Low pressure output 10 – 30mbar
>> Inlet pressure range 150 – 350 mbar
>> According gen-set power there are several types (dimensions):
>> Code name Note
IBF-GT25 DN25, Outlet 1× 1BSP, up to 250kWe
IBF-GT40 DN40, Outlet 2× 1BSP, 250 – 650 kWe
IBF-GT50 DN50, Outlet 2× 5/4BSP, 600 – 1000 kWe
IBF-GT50A DN50, Outlet 4× 1BSP, 600 – 1000 kWe
IBF-GT65 DN65, Outlet 4× 5/4BSP, 1000 – 1650 kWe
IBF-GT80 DN80, Outlet 4× 5/4BSP, 1650 – 2200 kWe
52 Bi-fuel products
Colour
Displays
Remote displays provide users with a choice of improved data visibility and the ability
to communicate over greater distances.
53
InteliVision 12Touch
12,1“ Colour Display Unit Touchscreen
>> Industrial operator panel equipped with 12,1” >> Adaptive and colour AlarmList >> Face is sealed to IP65
colour TFT multi-touch screen with resolution >> Large History screen >> EMC, climatic and mechanical tests
of 1280 × 800 pixels >> Adjustable setpoints help >> CE certification
>> Touch based Graphical User Interface, >> Communication connection via RS-485, CAN >> Supported controllers :
support for multi-touch gestures or Ethernet • InteliSys GAS
>> Plug & Play operation (auto configuration >> Multilanguage support • InteliGenNT BaseBox
based on controller application) >> Integrated easy to use mounting system • InteliGenNTC BaseBox
>> Complete access to all control and >> Designed to be mounted in either monitoring • InteliSysNTC BaseBox
monitoring functions or engine room • InteliMainsNTC BaseBox
>> Fast and intuitive navigation >> Industrial and robust design • InteliSysNTC Hybrid
>> Extended trends monitoring screen >> Rugged housing manufactured from a single • InteliDrive DCU Marine from HW version 2.0
>> Compatible with ScreenEditor software piece of aluminium alloy • InteliDrive Mobile from SW version 2.6.0
>> USB flash disk file storage >> Chemically strengthened front glass
(export/import trends, history, archive of (8 times stronger than normal glass)
controller and InteliVision 12Touch firmware >> Sun-readable display (1000 cd/m2)
and others to a USB stick) >> Automatic brightness control
>> User’s pictures import >> Operating temperature: –30 to + 70°C
Order code
RD1IV12TBZH
54 Colour displays and Modules Colour displays
InteliVision 18Touch
18,5“ Colour Display Unit Touchscreen
>> Panel suitable for use with a wide range >> Setpoints configurable from one device
of ComAp controllers >> History logs of all controllers
>> Successor to the InteliVision 17Touch >> Fullscreen mode with lock protection/PIN
>> Display for monitoring and control >> Onscreen keyboard
of the entire site >> Windows operating system
>> Possible to use for remote monitoring
and control through Internet
>> 18,5“ LED backlit projected capacitive
touchscreen with a resolution of 1366 × 768
pixels
>> Operating temperature extends
from -10 °C to +60 °C
>> Powerful Intel® Celeron® quad core
processor J1900
>> 3× USB, 2× mini-PCIe sockets, 1× CFast,
2× RS232/422/485/, 2x RJ45
>> 32 GB SSD
>> Front protection compliant with IP66
>> Mounting support: panel/wall/stand/VESA
100mm × 100mm
Order code
>> Power input 12-30 VDC
RD31840PBIE >> ComAp PC tools preinstalled
>> Colour display unit for localized visualisation >> For InteliSysNT, InteliGenNT, InteliMainsNT, InteliDrive DCU
>> InteliVision 5 is compatible with the following product line of and InteliDrive Mobile Controllers
controllers: InteliGenNT, InteliSysNT and InteliMainsNT >> 8” colour TFT display with resolution of 800 × 600 pixels
>> 5,7” Colour TFT Display with resolution of 320 × 240 pixels >> Plug & Play operation (auto configuration based on controller
>> Local and Remote display for single controller monitoring application)
>> Plug & Play operation (auto configuration based on >> Complete access to all control and monitoring functions
controller application) >> More information in less time
>> Direct connection to the controller (converters are not needed) >> Fast and intuitive navigation
>> Simple, fast and intuitive control >> Trends monitoring screen
>> Easy drag and drop screen configuration in graphical editor >> USB flash disk file storage (export/import trends, history, archive of
>> Five active buttons – fast access to important data controller and InteliVision 8 firmware to a USB stick)
>> Configurable active buttons >> Quick auto login with USB stick
>> Support of Tiers 4 icons >> User’s pictures import
>> Mounting screw available at the rear face of InteliVision 5 to mount >> Easy Drag & Drop screen configuration in graphical editor
a compatible controller >> Adaptive and colour AlarmList
>> Same language support as the controller including graphic languages >> Configurable soft keys buttons
>> Communication connection via RS-485 (galvanically separated) >> Fast skip to any screen
>> Same cut out as InteliGenNT >> Binary signal activation – S/R button / toggle button / pulse generator
>> Operating temperature: –30 to +70°C >> Association to various Gen-set commands
>> Large History screen
INTELIVISION 5 INTELIVISION 8
56 Colour displays and Modules Colour displays
InteliVision 12Touch OEM InteliVision 5 CAN InteliVision 8 Marine
12,1“ Colour Display Unit Touchscreen 5,7“ Colour Display Unit with CAN Bus Marine Approved 8“ Colour Display
Interface Unit for InteliGenNT/InteliSysNT and
InteliDrive Family of Controllers
>> Marine Approved 12,1” Colour Display Unit >> 5,7” Colour TFT Display with resolution of >> Marine approved display unit for either
without name and company logo on its front 320 × 240 pixels InteliGenNT / InteliSysNT or InteliDrive
face >> Local and Remote display for single controllers
>> 12,1” colour, multi-touch screen, TFT display controller monitoring >> 8” colour TFT display with resolution
unit with resolution of 1280 × 800 pixels >> Plug & Play operation (auto configuration of 800 × 600 pixels
>> Touch based Graphical User Interface, based on controller application) >> Controlled by active buttons
support for multi-touch gestures >> Direct connection to the controller >> Trends monitoring screen as a standard
>> Plug & Play operation (auto configuration (converters are not needed) feature
based on controller application) >> Easy drag and drop screen configuration in >> Simpler, faster and more intuitive control
>> Complete access to all control and graphical editor >> More information in less time
monitoring functions >> Five active buttons – fast access to >> Same language support as InteliGenNT /
>> Fast and intuitive navigation important data InteliSysNT and InteliDrive controller
>> Extended trends monitoring screen >> Support of Tiers 4 icons >> Easy Drag & Drop screen configuration in
>> Compatible with ScreenEditor software >> Same language support as the controller graphical editor
>> USB flash disk file storage including graphic languages >> Direct connection to the controller
(export/import trends, history, archive of >> Communication connection via RS-485 / CAN (converters are not needed)
controller and InteliVision 12Touch firmware >> Operating temperature: –20 to +70°C >> The same dimensions as IS-Display /
and others to USB stick) >> Supported controllers: InteliSysNT
>> User’s pictures import • InteliDrive DCU Industrial (including cut out dimensions)
>> Adaptive and colour alarm list • InteliDrive DCU Marine >> It is possible to mount InteliSysNT BaseBox
>> Large History screen • InteliDrive Mobile to the rear side of InteliVision
>> Adjustable setpoints help • InteliDrive Mobile Logger >> Can be used as a replacement for (or an
>> Multilanguage support • InteliGenNTC Basebox alternative to) IG-Display, IS-Display or
>> Communication connection via RS-485, • InteliSysNTC BaseBox I-RD-CAN
CAN or Ethernet • InteliSys GAS
>> Integrated easy to use mounting system >> Also available: InteliVision 5 CAN Backlit,
>> Designed to be mounted in either a modification with backlit buttons and
monitoring or engine room marine certifications
>> Industrial and robust design Order code
Order code INTELIVISION 5 CAN, Order code
RD112OEMBZH INTELIVISION 5 CAN BACKLIT INTELIVISION 8 MARINE
The comprehensive family of extension modules and control accessories enable users to
custom design control systems to meet individual project requirements and bring wider
scope and flexibility to ComAp control products.
59
InternetBridge-NT InternetBridge-NT 4G CM-Ethernet CM-4G-GPS
Communication Module Communication Module with Internet / Ethernet plug-in 4G & GPS plug-in
with Cellular/Ethernet Cellular/Ethernet Connection communication module communication module
Connection
>> Internet connection for one >> Ethernet/Internet >> Plug-in module for functional >> Plug-in module for functional
or more ComAp controllers, connection module extension of new InteliLite extension of new InteliLite
either by Ethernet cable or by >> For single or multiple controllers. controllers
built in 3.75G Cellular modem controllers, connection >> Internet / Ethernet module with >> Communication module
>> Wireless high speed via CAN2, RS485 or 10/100 Mbit interface over providing wireless internet
GPRS/UMTS modem built in RS232 (single) RJ45 socket connectivity
>> Supports all cellular packet >> 100Mbps ethernet port for >> Embedded webserver >> 4G – LTE
data systems from GPRS to wired ethernet connection for monitoring and basic >> 3G – WCDMA, HSDPA,
HSPA (2.5G to 3.75G) >> Built-in cellular modem for adjustments HSUPA, HSPA+
>> Full Multiband support – wireless Internet connection >> ModBus TCP support >> 2G – GPRS, EDGE
modem works globally >> Supports all cellular network >> Full SNMP V1/V2C support >> GSM (850 / 900 /
>> Ethernet wired connection for types up to LTE (4G) >> ComAp TCP for remote 1800 / 1900 Mhz)
local LAN connection >> Three variants of the product access and full controll over >> Remote monitoring and control
>> Single module can be used for usage in different InteliConfig capabilities via InteliConfig,
for multiple controllers on the geographical areas >> SMTP protocol with WebSupervisor and active
same site >> Communication with all authentification for active SMS / Emails alerts and control
(connected via CAN or RS485) ComAp tools directly or via e-mails sending >> WebSupervisor system
>> MODBUS/TCP, SNMP protocol AirGate >> AirGate technology support for support for web based
support – direct connection >> SNMP, MODBUS/TCP easy connection – no need of monitoring and control of one
to building management and available on ethernet port public and static IP address or multiple controllers at the
other systems >> Sends important controller same time
>> Includes ComAp AirGate events as active e-mails >> AirGate technology support for
technology – easy plug-and- and/or SMS easy connection
play connection anywhere (no >> Automatic SMS message on
fixed IP needed) alarm events
>> SMS control of gen-set/engine
>> GPS location with geofencing
Order code and tracking
CM2IB4GABFB
Order code CM2IB4GEBFB Order code Order code
IB-NT CM2IB4GJBFB CM2ETHERXBX CM14GGPSXBX
>> Plug-in module for functional >> Plug-in module for functional >> Plug-in communication module >> Plug-in communication module
extension of new InteliLite extension of new InteliLite for InteliATSNT, InteliLiteNT, for InteliLiteNT, InteliCompactNT
controllers controllers InteliCompactNT and InteliDrive and InteliDrive Lite controllers
>> Communication module >> Communication module with Lite controllers used with GSM Modem function for
providing wireless internet dual port for RS232 and a standard firmware dial-up connection
connectivity over GPRS and RS485 providing 2 separate >> 10/100 MBit ethernet interface >> GPRS support for wireless
GSM communication and indepandent COM in RJ45 socket internet connection
>> Remote monitoring and control channels >> Web interface for basic >> WebSupervisor system
capabilities via InteliConfig, >> Supports Modbus RTU, ECU monitoring and adjustment support for web based
WebSupervisor and active link and direct connecton to of the controller monitoring and control of one
SMS / Emails alerts and control InteliConfig >> ComAp/TCP protocol for or multiple controllers at the
>> WebSupervisor system remote access from LiteEdit same time
support for web based or InteliMonitor >> AirGate technology support for
monitoring and control of one >> Modbus/TCP protocol for easy connection over GPRS,
or multiple controllers at the integration of the controller into overcomes many of the issues
same time building management systems traditionally experienced
>> AirGate technology support for or other remote monitoring with internet connection to
easy connection purposes embedded systems
>> Automatic SMS message on >> SNMP v1 Agent >> WebSupervisor and AirGate
alarm events >> SMTP protocol with support
>> SMS control of gen-set/engine authentication for sending >> Remote access from LiteEdit
of active e-mails or InteliMonitor
>> Web-based configuration and >> Mobile and wireless solution
firmware upgrade
of the module
>> AirGate technology support
for easy connection
IL-NT RS232 >> Easily removable plug-in GPS >> Communication module for
>> Extension board containing communication module with >> Plug-in GPS module for multiple engine installations,
RS232 port for InteliLiteNT, USB device interface InteliDrive Mobile / Mobile remote displays and
InteliCompactNT and InteliDrive >> For InteliLiteNT, InteliCompactNT, Logger controllers redundancy communication
Lite controllers InteliDrive Lite controllers >> GPS function of exact >> Interface for CAN1 Extension
controller location and J1939 modules
IL-NT RS232-485
>> Enables protection against >> Interface for CAN2
>> Dual port module with RS232
unwanted manipulation of the Inter-controller
and RS485 interfaces at
controller (GeoFencing) >> Interface for J1708
independent COM channels
>> Module is supplied with redundancy line
>> The RS232 is connected to
antenna connector >> Marine Approved
COM1 and RS485 to COM2
>> UL certified
>> Compatible with InteliLiteNT, GSM
>> Galvanic separate RS485
InteliCompactNT and >> GSM Modem function for for IV12TOEM or for 3rd party
InteliDrive Lite. dial-up connection system connection, for up
>> GPRS support for wireless to 1000 meters
internet connection
>> WebSupervisor and Airgate
support
>> Remote access from
DriveMonitor or InteliMonitor
>> Automatic SMS message on
alarms or events
>> SMS control of gen-set
>> Communication bridge for >> Versatile programmable >> Provides intercontroller CAN >> Intercontroller CAN bus
sites with multiple controllers interface unit between bus redundancy by adding extension (where the maximum
for local or remote monitoring InteliGenNT, InteliSysNT or parallel RS485 communication distance limit would be
and control InteliDrive controllers and any bus exceeded)
>> Direct (RS232,RS485), modem, Modbus RTU device >> Provides intercontroller bus >> Intercontroller CAN bus bus-tie
Modbus or USB connection to >> Predefined databases of values extension as well bridging – makes groups of
multiple controllers for Cummins PCC, CAT EMCP, >> Intended for achieving high controllers in segments
>> Communication speed up CAT PL1000 and other devices reliability of the intercontroller A and B “invisible” one for
to 57600 bps (including >> Suitable for monitoring circuit communication in complex another depending on bus-tie
Modbus mode) breakers, flow meters, PLCs applications where the parts of breaker state, keeping the PC
>> Analog / GSM / ISDN / CDMA etc. with Modbus RTU protocol the technology are separated communication in function
modem support >> RS485/RS232 interfaces from each other and the for all controllers
>> I-CB/Modbus together intercontroller bus is exposed >> One or more I-CR modules
with the controller act as a to a risk of interruption can be used
Modbus master >> I-CR-R may be used as >> UL certified
a redundancy module for
a maximum of 20 controllers
(counted all controllers on the
CAN2 bus)
>> UL Certified
>> Plug-in module for functional >> Hybrid current input & binary >> Hybrid binary input/output >> Extension plug-in module
extension of new InteliLite input/output module module increasing the number of
controllers >> Applicable to InteliCompactNT >> Applicable to InteliLiteNT v1.5 analog inputs and output of
>> Extension module with 8 SPtM v. 1.2 and higher, and higher, InteliCompactNT v1.2 selected engine controllers
configurable binary terminals InteliCompactNT MINT v. 1.3 and higher, InteliATSNT v2.0 and >> 4 configurable analog inputs
for inputs or outputs and higher higher and InteliDrive Lite v1.6 for the sensors (in range
>> Possibility to connect a current >> One additional AC current (CT) and higher 0 – 2400 Ω; 0/4-20mA;
transformer for earth fault measuring input >> Up to 8 additional configurable 0-4VDC)
current measurement and >> Up to 7 configurable additional binary inputs or outputs >> 1 configurable analog output
protection binary inputs or outputs for the sensor (in range
0/4–20mA; 0-4,5VDC;
PWM 5V/500Hz)
>> Gauge driver plug-in interface >> Extension plug-in module >> Inteli AIN8 module allows >> Inteli AIN8TC extension
>> Applicable to InteliLiteNT, increasing the number of users to expand the amount of module allows customers up
InteliCompactNT and analog outputs and binary analog inputs for sensors and to 8 analog input channels
InteliDrive Lite inputs of selected engine add Impulse/RPM input that for measuring temperature by
>> Up to 8 gauges (such as VDO, controllers can be attached to a controller thermocouples
Datcon) can be driven by >> 4 configurable analog outputs >> Up to 8 configurable inputs >> The Inteli AIN8TC is useful in
one controller (output range: 0 to +VBatt ±1V) (sensors) can be attached to situations where extremely
>> 4 confiurable binary inputs the controller, and up to ten accurate temperature readings
of the Inteli AIN8 modules can are required
be connected to InteliSysNT, >> Up to 10 modules can be
InteliGenNT, InteliMainsNT connected to a each controller,
controllers (up to four in case making accurate temperature
InteliDrive DCU controller) readings both simple and
>> The Inteli AIN8 is determinate reliable
for the InteliSysNT, InteliGenNT, >> It is compatible with J, K and
InteliMainsNT and InteliDrive L types of thermocouples and
DCU controllers cold junction compensation is
>> Current (active or passive supported
sensors):
• ±20mA , 0-20mA, 4-20mA
Voltage
• ±1V, 0-2,4V, 0-5V, 0-10V
• Lambda probes
• Thermocouples are not
supported (the measuring
loop was designed for
lambda probes, what
caused non-support of
thermocouples)
Order code Order code Order code Order code
IL-NT-AOUT8 IL-NT-IO1 I-AIN8 I-AIN8TC
>> The extension module Inteli >> Inteli AIO9/1 module is designed >> 8 configurable analog outputs >> Configurable 8 binary and
IO8/8 offers users more binary for applications where DC >> Outputs are configurable to: 4 analog inputs
inputs and outputs for ComAp measurement of current and • 0-10VDC or >> Configurable 8 binary and
controllers voltage is necessary – such as • 0/4-20mA range or 1 analog output
>> The unit offers the user the Hybrid applications • 1200 Hz pwm >> LEDs indicate the state of
flexibility to configure the unit >> Module is equipped with: >> Up to four I-AOUT8 can be binary inputs/outputs
to have 8 binary inputs, 8 >> Analog inputs: connected to one controller >> Measures values from Pt100
binary outputs, and 2 analog • 4 channels for differential >> UL certified and Ni100 sensors
outputs, or 16 binary inputs, voltage measurement: >> Analog inputs (resistance
0 binary outputs and 2 analog range ±65V DC (for range 0-250 Ω, voltage range
outputs via switches inside the example battery voltage 0-100mV, current range
controller measurement) 0-20mA – selectable via
>> The Inteli IO8/8 is compatible • 4 channel equipment jumper)
with the InteliDrive DCU, sensors: thermocouples >> Up to 4 IGS-PTM can be
InteliMainsNT, InteliGenNT and J,K,L , ±75mV (for current connected to the controller
InteliSysNT ranges of controllers measurement via resistor >> UL certified
>> Up to 12 Inteli IO8/8 module shunts
(in configuration 8/8) can be • 1 channel for resistance
connected to the controller measurement 0-2400Ω
(InteliSysNT / InteliGenNT / (sensors: 0-2400Ω, PT1000
InteliMainsNT ) or NI1000)
>> Up to 6 Inteli IO8/8 module >> Analog output with options:
(in configuration 16/0) can be 0-20mA, 0-10V or PWM
connected to the controller >> Currently this module is
(InteliSysNT / InteliGenNT / supported in the software
InteliMainsNT ) IGS-NT 3.1.1, IM-NT 3.1.1
or higher
>> 15 programmable LEDs with >> Interface ensuring voltage >> ECON-4 is digital speed >> Interface module for InteliDrive
configurable colours matching between InteliGenNT governor dedicated for speed DCU Industrial, InteliDrive CCU
red/green/yellow or InteliSysNT controller and control of gas or diesel engines and InteliDrive DCU Marine
>> Customizable labels generator AVR >> ECON-4 guarantees precise controllers for full support of
>> Local horn output >> 4 kV electric insulation and fast speed control in internal PLC (programmable
>> Lamp test function between controller and AVR variable load applications logic) in wide range
>> Maximal distance 200m from >> DIN rail design (island operation) and precise of applications
the controller load control in network parallel >> Module is mounted directly on
>> Up to 4 units can be connected operation the controller body
to the controller >> ECON-4 can control different >> Inputs and outputs:
>> UL certified types of actuators (linear, • RPM1, RPM2: inputs for
bridge, low voltage signal) frequency measuring – up
providing up to 8A continuous to 8 kHz
signal which makes it a general • IMP1, IMP2: inputs for
speed controller for almost integral (consumption)
every actuator on the market measuring up to 60 Hz
for engines in range up to few • AOUT1, AOUT2: analog
MWel outputs 0 – 10VDC
>> Additionally ECON-4 can be or 0 – 20 mA
connected with the gen-set • Speed Governor Output:
control system via CAN line ±10VDC or ±10VDC via
which significantly reduce 10kΩ or PWM (1,6kHz )
and simplify the wiring and >> UL certified
commissioning work
>> Isochronous/droop mode
>> Actuator position feedback
utilisation
EP250
>> Redundant engine protection >> Stepper motor driver, >> Microprocessor-controlled >> Sealed electronic construction
unit for InteliDrive Marine dedicated to control various device designed for control >> Protection: short circuit /
controller flaps, actuators, e.g. Air/Fuel and regulation systems overload / over voltage /
>> Backup module for ratio Mixers which ensures >> 3 binary inputs (increase, over temperature / reverse
marine engines precise position control of such decrease, init), one 2-pole battery
>> Automatic switchover between a device.Capable to control 2 output of variable resistance >> Universal AC input ranges
primary and secondary stepper motors from one unit >> Position of the wiper is >> Low ripple output
power supply at once, both independently, controlled by binary inputs >> Naturally cooled
>> Monitors function of main which makes it ideal for all >> Current percentage value is >> Voltage adjust potentiometer
InteliDrive Marine controller engine sizes and arrangements indicated by LED bar graph on >> Optional fail alarm relay1)
>> In case of InteliDrive Marine (in-line and V-type) the front panel >> Charger can be used as
failure, it switches to the >> Capable to operate in various >> Setpoints (position change rate a standalone power supply
backup mode and protects modes, ranging from mode with and init position) are adjustable
the engine position feedback or based on via DIP switches
>> RPM input with hardwired calibration end-points EP300
overspeed protection >> Fully supported over CAN >> 3 binary inputs (increase,
>> Fuel and Stop solenoids with communication in specific decrease, init), one 3-pole
BW detection ComAp controllers and output of variable resistance
>> Built-in self-diagnostics feature firmware – e.g. InteliSys Gas (potentiometer)
which makes the wiring simple >> Current percentage value is
and all parameters and values indicated by LED display on
are accessed from the main the front panel
control unit >> Setpoints (position change
rate, position limits, init position
and others) are adjustable
via buttons and LED display 1)
This feature is available with InteliCharger 60 12-AF
on the front panel and InteliCharger 60 24-AF models, also offered by
ComAp.
>> 20 A nominal outputs >> 24 V / 10 A nominal output >> 12 V / 10 A nominal output >> 24 V / 5 A or 12 V / 6 A nominal
>> High power and efficiency >> Adjustable voltage >> Adjustable voltage and output (dual voltage)
>> High reliability and current output current output >> Adjustable voltage
>> Suits all battery types >> Microprocessor controlled >> Microprocessor controlled and current output
>> Fully automatic operation charging algorithm charging algorithm >> Microprocessor controlled
>> 24 V nominal outputs >> Protections: short circuit / >> Protections: short circuit / charging algorithm
>> Naturally cooled – overload / over temperature overload / over temperature >> Protections: short circuit /
fan-less design / reverse battery / battery / reverse battery / battery overload / over temperature
>> Optional alarms under voltage under voltage / reverse battery / battery
(& bi-colour LEDs) >> Universal AC input range >> Universal AC input range under voltage
>> Optional intelligent multi- >> Naturally cooled >> Naturally cooled >> Universal AC input range
stage charge profile with >> Fail alarm relays >> Fail alarm relays >> Naturally cooled
auto equalise >> Charger can be used as >> Charger can be used as >> Fail alarm relay
>> Optional boost charging a standalone power supply a standalone power supply >> Charger can be used as
system >> Intelligent support for charging a standalone power supply
Open Lead Acid, Sealed Lead
Acid and Lead Gel batteries
ComAp‘s dedicated PC software and configuration tools ensure operating and monitoring
generators and engine controllers is both easy and accessible. The software is custom
designed to ensure the optimum performance of ComAp controllers and helps users
configure, supervise and monitor as well as manage and interpret trend information.
71
InteliMonitor
PC Monitoring Tool
for Inteli Controllers
Overview of all your assets’ actual status, alarm The flexible system provides a high level of
notifications, asset location on a map, detailed security, with the central administrator able
logging of data, historical trends, machine to determine users’ access rights for specific
control and management – all on one screen equipment within the fleet as well as appropriate
using WebSupervisor. information. In addition, event generated e-mails
can be created and sent to specific users to give
From your PC, tablet or mobile phone you can fast and efficient notification to improve decision
instantly reach the most important and relevant making or react to additional revenue
data. The responsive design ensures easy to generating opportunities.
use operation on any screen size.
For more information please visit
>> Map view of assets www.websupervisor.net
>> Table view with alerts
>> Quick detailed view Mobile apps also available.
>> Historical graphs and trends
>> Automatic weekly&monthly reports
>> Fast GUI
>> Single machine or group control
>> Quick connection to PC tools
>> Storage of history records from controller
>> LiteEdit is Windows software which provides following main functions: >> PC Configuration and Monitoring Tool supporting latest InteliLite and
>> To be used with InteliATSNT, InteliLiteNT, InteliCompactNT, InteliGen 200 controllers
MainsCompactNT, InteliDrive Lite and InteliPro controllers >> Remote control, monitoring and On-line / Off-line parameters
>> Remote control and monitoring, parameters adjustment adjustment with 3 levels of password protection
>> Controller configuration and programming, controller firmware >> Controller and module configuration, programming and cloning
upgrade, cloning of configuration >> Built in PLC Editor and PLC Monitor
>> Support of electronic engines >> Power format and ECU unit selection
>> Controller language translation >> Gen-set and ECU Alarm monitoring + complete real time history
>> Connection via USB, RS232, modem, internet or AirGate >> Custom ‚Welcome‘ screen editor
>> Search tool
>> Embedded manuals
>> Auto-hiding of unused setpoints
PLC Editor,
ScreenEditor PLC Editor inside
>> GenConfig is Windows based software which provides following >> DriveConfig is Windows based software which provides following
main functions: main functions:
• Modify the controller configuration – i.e. define peripherial • Modify the controller configuration – i.e. define peripherial
modules, assign functions and/or protections to inputs and modules, assign functions and/or protections to inputs and
outputs, create PLC program and other outputs, create PLC program and other
• Controller firmware upgrade • Controller firmware upgrade
• Adjust initial values of setpoints • Adjust initial values of setpoints
• Read/write configuration from/into the controller • Read/write configuration from/into the controller
• Load configuration from file, save it to file • Load configuration from file, save it to file
>> GenConfig 2.4 and higher contains the powerful graphic editor for >> DriveConfig 2.0 and higher contains the powerful graphic editor for
user-friedly creating the PLC program user-friedly creating the PLC program.
>> GenConfig 2.6.1 and higher contains Screen Editor, that allows you to >> DriveConfig 3.1 and higher contains ScreenEditor, that allows you to
personalise the interface on colour displays by managing screen type, personalise the interface on colour displays by managing screen type,
selecting instruments and creating backgrounds from a toolbox of selecting instruments and creating backgrounds from a toolbox of
graphical elements. graphical elements.
>> RemoteCommGuide is interactive communication guide for most >> Monitoring and archiving of ComAp controllers’ parameters
ComAp gen-set controllers. It is a part of ComAp PC Suite and values
>> This useful tool helps you to easily select the proper gen-set controller >> View of actual/historic trends in the controller
according to required application and communications >> On-line change of controller’s parameters for easy regulator setup
>> RemoteCommGuide solves problem with projecting of >> Supports connection to all Inteli-line controllers
communications and checks the wiring and settings during >> Enables parameter setting of ECON and INCON controllers
the commisioning >> Enables parameter setting of EMCON5 controller
>> Easier finding of required information >> The software is a part of Installation Packages of ComAp gen-set and
>> See only relevant information engine controllers
>> Automatically check the accessibility of required communications >> Without any activation WinScope works in Demo Mode, where there
>> Wizard for first steps with RemoteCommGuide makes easier to you can only browse previously saved data
understand the logic of SW >> Basic version allows monitoring of only one controller and max
>> Make Remote communications more understandable – need of less 4 channels
technical support
>> Information about all controllers in one place together
77
Controllers for single gen-set applications
InteliNano
InteliNanoNT PLUS
NT
PLUS inteliNano
inteliNanoNT MRS
NT
MRS 33 InteliLite
InteliLiteNTMRS
NT
MRS 33 InteliLite
InteliLiteNTMRS
NT
MRS 44 InteliLite
InteliLiteNT AMF
NT
AMF 88
Binary
Binaryinputs
inputs//outputs
outputs 66 // 662)2) 66 // 662)2) 44 // 4"
4" 44 // 4"
4" 44 // 6"
6"
Analog
Analoginputs
inputs 33 33 33 33 33
2 × 10
2 × 10AAbinary
binaryoutputs
outputs •• •• –– –– ––
Input
Input//output
outputconfigurations
configurations •• // •• •• // •• •• // •• •• // •• •• // ••
D+
D+battery
batterycharging
chargingalternator
alternatorcircuit
circuit •• •• •• •• ••
Magnetic
Magneticpickup
pickup –– •• –– –– ••
AMF
AMF//MRS
MRSfunctions
functions •• // •• –– // •• •• // •• •• // •• •• // ••
GCB
GCB//MCB
MCBcontrol
controlwith
withfeedback
feedback •• // •• •• // –– ••6)6) // ••6)6) ••6)6) // ••6)6) •• // ••15)
15)
3ph
3phvoltage
voltagemeasurement
measurementGen.
Gen.//Mains
Mains ••4)4) // •• •• // –– •• // –– •• // –– •• // ••
3ph
3phcurrent
currentmeasurement
measurement ––5)5) ••
•• •• ••
Frequency
Frequencymeasurement
measurementGen.
Gen.//Mains
Mains •• // •• •• // –– •• // –– •• // –– •• // ••
kW
kW//kWh
kWh//kVA
kVAmeasurement
measurement –– // –– // •• •• // •• // •• •• // •• // •• •• // •• // •• •• // •• // ••
Generator
Generatorprotections
protections •• •• •• •• ••
Earth
Earthfault
faultcurrent
currentprotections
protections –– –– –– –– ––
History
Historyfile
file •• •• •• •• ••
RTC
RTC//Battery
Battery –– // –– –– // –– –– // –– –– // –– –– // ––
PLC
PLC –– –– –– –– ––
Remote
Remotecontrol
control –– –– •• ••
4G
4G –– –– –– –– ––
Tracking
Tracking&&Geofencing
Geofencing –– –– –– –– ––
Active
ActiveSMS
SMS//E-mails
E-mails –– –– // –– // –– // ––
AirGate
AirGate –– –– –– ––
WebSupervisor
WebSupervisor –– –– –– –– ••
USB
USBintegrated
integrated •• •• 7)7) 10)
10)
ECU
ECUsupport
supportvia
viaCAN
CAN •• •• –– •• ––
Modbus
Modbussupport
support//SNMP
SNMPsupport
support//SNMP
SNMPtraps
traps –– // –– // –– –– // –– // –– // –– // –– // –– // –– // –– // ––
Plug-in
Plug-inmodules
modules –– –– ••8)8) ••8)8) 8)8)
1) –– –– –– –– ––
Manual
Manualspeed
speedcontrol
control1)
Total
Totalfuel
fuelconsumption
consumption –– –– –– –– ––
Fuel
Fuelpump
pump –– –– –– –– ––
Dummy
Dummyload
load//Load
Loadshedding
shedding –– –– –– –– ••
Auto.
Auto.temperature
temperaturebased
basedheating
heating&&cooling
cooling –– –– –– –– ––
Analog
Analogcalibration
calibration –– –– –– –– ––
Connection
Connectiontype
typeautodetect
autodetect •• •• –– –– ––
Tier ––
Tier44Final
Finalsupport
support –– –– –– ––
KEY • Included GCB: Generator circuit breaker 3) Analog inputs are shared with binary inputs 6) Manual / Automatic GCB and
– Excluded MCB: Mains circuit breaker 4) 1 ph; 3 ph when used as MRS controller MCB control, but without feedback
Optional – plug-in module required 1) For ECU engines 5) 1 ph is available 7) Only with order code IL2M3USBXAB
2) 1 binary input is shared with binary output
78 Comparison tables
InteliLite
InteliLiteNT AMF
NT
AMF 99 InteliLite
InteliLite 99 InteliLite
InteliLite MRS
MRS 11
11 InteliLite
InteliLite MRS
MRS 16
16 InteliLite
InteliLite AMF
AMF 20
20 InteliLite
InteliLite AMF
AMF 25
25
44 // 6"
6" 66 // 6"
6" 66 // 6"
6" 77 // 7"
7" 77 // 7"
7" 88 // 8"
8"
33 33 33 44 33 44
–– •• •• •• •• ••
•• // •• •• // •• •• // •• •• // •• •• // •• •• // ••
•• •• •• •• •• ••
•• •• •• •• •• ••
•• // •• •• –– // •• –– // •• •• // •• •• // ••
•• // ••15)
15) •• // •• •• // –– •• // –– •• // •• •• // ••
•• // •• •• // •• •• // –– •• // –– •• // •• •• // ••
•• •• •• •• •• ••
•• // •• •• // •• •• // –– •• // –– •• // •• •• // ••
•• // •• // •• •• // •• // •• •• // •• // •• •• // •• // •• •• // •• // •• •• // •• // ••
•• •• •• •• •• ••
–– –– ––
•• •• •• •• •• ••
•• // •• •• // –– •• // –– •• // •• •• // –– •• // ••
–– –– •• •• •• ••
–– ••
–– –– –– ––
// –– // –– // –– // ––
–– –– ––
–– –– ––
•• •• •• ••
•• •• •• •• •• ••
// –– // –– // –– // –– // –– // –– // // // –– // –– // //
8)8) 14)
14) 14)
14) 14)
14) 14)
14) 14)
14)
–– •• •• •• •• ••
•• –– –– •• –– ••
–– •• –– •• –– ••
•• –– –– •• –– ••
–– –– –– •• –– ••
–– –– –– •• –– ••
–– •• •• •• •• ••
–– •• •• •• •• ••
8) IL-NT RS232, IL-NT RS232-485, 10) Only with order code IL2M4USBXAB 13) The same as 8) plus 15) Without breaker feedback
IL-NT GPRS, IL-NT S-USB, 11) Plug-in module required IB-Lite and IC-NT CT-BIO7
IL-NT AOUT8, IL-NT BIO8 12) The same as 8) plus IB-Lite 14) CM-RS232-485, CM-GPRS, CM-4G-GPS,
CM-Ethernet, EM-BIO8-EFCP
Comparison tables 79
Controllers for parallel gen-set applications
InteliGenNT BaseBox InteliGenNTC BaseBox InteliSysNTC BaseBox InteliGen GSC BaseBox
Binary Inputs / Outputs 12 / 12 (108 / 108)10) 12 / 12 (108 / 108)10) 16 / 16 (112 / 112)10) 16 / 16 (108 / 108)10)
10) 10) 10)
Analog Inputs / Outputs 3 / 0 (83 / 32) 3 / 0 (83 / 32) 4 / 1 (83 / 33) 3 / 0 (83 / 32)10)
Configurable Shared / Distribute I/O •/• •/• •/• •/•
Maximum controllers on CAN 992* 992* 992* 992*
Predefined / Configurable Protections •/• •/• •/• •/•
AMF Function • • • •
GCB control with feedback • • • •
Integrated PLC ••• ••• •••• •••
Input / Output configuration •/• •/• •/• •/•
Alternate configuration / Force Value •/• •/• •/• •/•
Voltage measurement Gen / Mains (bus) 3 ph / 3 ph 277V 3 ph / 3 ph 120V / 277V 3 ph / 3 ph 120V / 277V 3 ph / 3 ph 277V
Current measurement 3ph + 1 / 6w IDMT overcurrent 5A 3ph + 1 / 6w IDMT overcurrent 1A/5A 3ph + 1 / 6w IDMT overcurrent 1A/5A 3ph + 1 / 6w IDMT overcurrent 5A
kW / kWh / kVA measurement •/•/• •/•/• •/•/• •/•/•
Acccuracy U/I/P/Q 1% / 2% / 3% / 3% 1% / 2% / 3% / 3% 1% / 2% / 3% / 3% 1% / 2% / 3% / 3%
Display External External External External
InteliVision 5, InteliVision 8, InteliVision 5, InteliVision 8, InteliVision 5, InteliVision 8, InteliVision 5, InteliVision 8,
Remote displays InteliVision 12Touch InteliVision 12Touch InteliVision 12Touch InteliVision 12Touch
InteliVision 18Touch InteliVision 18Touch InteliVision 18Touch InteliVision 18Touch
Extension / plug in modules •12) / - •12) / - •12) / - •12) / -
CAN1, CAN2, RS232, 2× RS485, USB,Ether- CAN1, CAN2, RS232, 2× RS485, USB,Ether-
CAN1, CAN2, RS232, RS485, CAN1, CAN2, RS232, RS485,
Controller’s communication interfaces Ethernet8), Modbus RTU, SNMP13)
net, Modbus RTU, Modbus TCP, SNMP, net, Modbus RTU, Modbus TCP, SNMP,
Ethernet8), Modbus RTU, SNMP13)
AirGate, Web server AirGate, Web server
Field BUS support - Slave Modbus support • • • •
Field BUS support - Modbus Master • (I-CB Modbus) • (I-CB Modbus) • (I-CB Modbus) • (I-CB Modbus)
Communication modules (via CAN) InternetBridge-NT, I–LB+, I–CR, I–CB InternetBridge-NT, I–LB+, I–CR, I–CB InternetBridge-NT, I–LB+, I–CR, I–CB InternetBridge-NT, I–LB+, I–CR, I–CB
Redundancy I-CR-R I-CR-R I-CR-R I-CR-R
SMS / Email Alerts •/• •/• •/• •/•
ECU support • • • •
Tier4Final / Stage V •/• •/• •/• •/•
Forward / Reverse synchronizing
/ Mains parallel operation •/•/• •/•/• •/•/• •/•/•
Multiple operation / Power Management System • / •14) • / •14) • / •14) • / •14)
History (max records) / Configurable 1) 1000 / • 1000 / • 1000 / • 1000 /•
SUS / GeCon functionality •/• •/• •/• •/•
Pre-morten history – – • –
Timers / Schedulers programmers •/• •/• •/• •/•
General Certifications CE, UL Listed CE, UL Listed CE, UL Listed CE, ongoing UL listed
Marine certifications • • • planned RRR
European Requirements for Generators,
Grid codes certifications – – – and VDE-AR-N 4105:2018, VDE-AR-N
4110:2018, including Single Fault Tolerance
KEY • Included CAN1 For peripheral modules and ECU (J1939) 3) With IG-IOM or IGS-PTM
– Excluded CAN2 Intercontroller can; monitoring 4) With IL-NT AOUT8 and IG-IOM or IGS-PTM
Optional – plug-in module required 1) Depends on number of values in history record 5) With IC-NT CT-BIO7
2) With IL-NT BIO8 and IG-IOM or IGS-PTM
80 Comparison tables
InteliGen GSC-C BaseBox InteliSys GSC-C BaseBox InteliGen 200 InteliGen 500 InteliGen NTC
12 / 12 (108 / 108)10) 16 / 16 (144 / 88)10) 9 / 8 (96 / 56)10) 9 / 8 (96 / 56)10) 12 / 12 (108 / 108)10)
10) 10) 10) 10)
3 / 0 (83 / 32) 8 / 1 (84 / 33) 4 / 0 (32 / 10) 4 / 0 (32 / 10) 3 / 0 (83 / 32)10)
•/• •/• -/- -/- •/•
992* 992* 32 32 992*
•/• •/• •/• •/• •/•
• • • • •
• • • • •
••• •••• • •• ••
•/• •/• •/• •/• •/•
•/• •/• •/- •/- •/•
3 ph / 3 ph 120V / 277V 3 ph / 3 ph 120V / 277V 3 ph / 3 ph 120V / 277V 3 ph / 3 ph 120V / 277V 3 ph / 3 ph 120V / 277V
3ph + 1 / 6w IDMT overcurrent 1A/5A 3ph + 1 / 6w IDMT overcurrent 1A/5A 3ph + 1 / 6w IDMT overcurrent 5A 3ph + 1 / 6w IDMT overcurrent 5A 3ph + 1 / 6w IDMT overcurrent 1A / 5A
•/•/• •/•/• •/•/• •/•/• •/•/•
1% / 2% / 3% / 3% 1% / 2% / 3% / 3% 1% / 1% / 2% / 2% 1% / 1% / 2% / 2% 1% / 2% / 3% / 3%
External External LCD 132x64 TFT 5" 800x480 LCD 128x64
InteliVision 5, InteliVision 8, InteliVision 5, InteliVision 8, InteliVision 5, InteliVision 8,
InteliVision 12Touch InteliVision 12Touch soon soon InteliVision 12Touch
InteliVision 18Touch InteliVision 18Touch InteliVision 18Touch
• • • • •
• (I-CB Modbus) • (I-CB Modbus) - - • (I-CB Modbus)
InternetBridge-NT, I–LB+, I–CR, I–CB InternetBridge-NT, I–LB+, I–CR, I–CB I-CR I-CR InternetBridge-NT, I–LB+, I–CR, I–CB
I-CR-R I-CR-R I-CR-R I-CR-R I-CR-R
•/• •/• •/• •/• •/•
• • • • •
-/- •/• •/• •/• •/•
•/•/• •/•/• •/•/• •/•/• •/•/•
• / •14) • / •14) •/• •/• • / •14)
1000 / • 4000 / • 350 / - 500 / - 500 / •
•/• •/• -/- -/- •/•
– • – – –
•/• •/• •/• •/• •/•
CE, ongoing UL listed CE, ongoing UL listed CE, UL Listed CE, UL Listed CE, UL recognised
planned RRR planned RRR - - •
European Requirements for Generators, and European Requirements for Generators, and
VDE-AR-N 4105:2018, VDE-AR-N 4110:2018, VDE-AR-N 4105:2018, VDE-AR-N 4110:2018, - -/- -
including Single Fault Tolerance including Single Fault Tolerance
6) IGL-RA15, IG-IOM, IGS-PTM 10) With extension modules, see 12) 13) With InternetBridge-NT
7) IC-NT CT-BIO7 is already included in the controller 11) More PLC blocks may vary according to the used firmware 14) With IGS-NT-LSM+PMS dongle
8) With communication modules 12) Inteli AIN8, Inteli AIN8TC, Inteli IO8/8, Inteli AIO9/1, 15) CM-Ethernet, CM-4G-GPS, CM-GPRS, CM-RS232-485, EM-BIO8 EFCP
9) With MainsCompactNT IS–AIN8, IS–AIN8TC, IS–BIN16/8, I–AOUT8, IGL–RA15, IGS–PTM 16) With CM-Ethernet
81
Controllers for engine driven and bi-fuel applications
InteliDrive InteliDrive DCU InteliDrive DCU InteliDrive
InteliDrive WP InteliDrive IPC InteliBifuel
Lite Industrial Marine Mobile
16 Digital inputs
9 Digital inputs
5× Digital inputs 5× Digital inputs 7× Digital inputs 14× Digital inputs 14× Digital inputs (4× BW detection)
Binary inputs 3× RPM inputs
1× RPM 1× RPM 1× RPM 1× RPM 1× RPM 4× RPM
3× Impulses Inputs
2× Impulse inputs
8× Hi-side 3 A
switches with BW
8× Hi side 0,5 A
detection
8× Hi-Side/Low
8× 3 A switches
5 Side
Binary outputs 5 7 14 14 configurable as:
(2× 10 A) or PWM switches 3A
• Hi-side
2× Hi-Side Safety
switches
switches 3A
• Low-side
• PWM
10 configurable
(0 – 5 V, 0 – 20
8 configurable 8 configurable mA, 0 – 24 V,
16 configurable
9 6 Configurable 9× Configurable (V, mA, Ω, (V, mA, Ω, 0 – 2500 Ohm,
Analog inputs (V, mA, Ω,
(3× Ω, 3× mA, 3× V) (V, Ω) (V, Ω) thermocoupler, thermocoupler, PT1000, isolated
PT100/1000)
PT100/1000) PT100/1000) thermocouple),
3 Non isolated
thermocouple inputs
8× configurable 6× configurable
On external modules On external modules On external modules On external modules (V, mA) (0 – 10 V, 0 – 20 mA)
Analog outputs 1× PWM (1× IL-NT AIO (1× IL-NT AIO (e.g. 2x ID-SCM, (e.g. 2× ID-SCM,
or 8× IL-NT AOUT8) or 8× IL-NT AOUT8) 8× I-AOUT8) 8× I-AOUT8) 1× Speed Governor 1x PWM 5V
(V, PWM) 450-3000Hz
82 Comparison tables
InteliDrive InteliDrive DCU InteliDrive DCU InteliDrive
InteliDrive WP InteliDrive IPC InteliBifuel
Lite Industrial Marine Mobile
1× CAN, 1× RS232, 1× CAN, 1× RS232, 2× CAN, 1×
2× CAN, 1× RS232, 2xCAN, 1x RS485,
Communication interfaces 1× USB 1× RS485, 1× USB, 1× RS485, 1× USB, RS232, 1× J1708, 2× CAN, 1× RS485
1× J1708 USB
1x Ethernet 1x Ethernet 1× RS485
ECU values Fix set Fix set Fix set Configurable Configurable Configurable Configurable
Displays text or/and Displays text or/and Displays text or/and Displays text or/and Displays text or/and Displays text or/and Displays text or/and
ECU – fault codes
numeric codes numeric codes numeric codes numeric codes numeric codes numeric codes numeric codes
KEY • Included
– Excluded
Comparison tables 83
Colour displays
InteliVision 5 InteliVision 5 CAN InteliVision 8 InteliVision 8 Marine InteliVision 12Touch InteliVision 12Touch OEM InteliVision 18Touch
Type TFT TFT TFT TFT TFT (IPS) TFT (IPS) TFT
Resolution 320 × 240 px 320 × 240 px 800 x 600 px 800 x 600 px 1280 x 800 px 1280 x 800 px 1366 × 768 px
Voltage Supply 8–36 VDC 8–36 VDC 8–36 VDC 8–36 VDC 8–36 VDC 8–36 VDC 12–30 VDC
Consumption 0,7A at 8 VDC 0,7A at 8 VDC 1A at 8 VDC 1A at 8 VDC 2A at 12 VDC 2A at 12 VDC max. 32,4W at 12V
Operating Temp. –30 to +70°C –20 to +70°C –20 to +70°C –20 to +70°C –30 to +70°C –30 to +70°C –10 to +60°C
RS485 – • • • • •
RS232 – • • – – •
2× USB 2.0
USB Port A / B –/– –/– •/• •/• 2× / • 2× / • 1x USB 3.0
ETH – – – – • • 2×
IP65 Connector – – – – – –
Multiple Gen-Set
Monitoring
– – – – – (will be implemented) – (will be implemented) •
Soft Keys • • • • – – –
Internal Buzzer – • – – • • –
1× AI (Backlight) 1× AI (Backlight)
I/O – 1× BO (Horn) – – –
1 × BO (Horn) 1 × BO (Horn)
Backlit Buttons – – – – – –
Screen Editor • • • • • • –
InteliMonitor – – – – – – •
Trends – – • • • • •
History • • • • • • •
AlarmList • • • • • • •
82 Comparison tables
InteliVision 5 InteliVision 5 CAN InteliVision 8 InteliVision 8 Marine InteliVision 12Touch InteliVision 12Touch OEM InteliVision 18Touch
Adjustable Status
Screen
– – – – • • –
Editable Setpoint
Description
– – – – • • –
Extended Import /
Export Functions
– – – – • • –
Skins – – – – • • –
UL • • • • • • •
Backlit Buttons – • – • – – –
Marine certification – – – • – • –
KEY • Included 1) InteliVision 12Touch is only compatible with selected Gen / Sys: InteliGenNT, InteliGenNT BaseBox, InteliGenNTC BaseBox,
– Excluded InteliSys models. Please visit www.comap-control.com InteliSysNT, InteliSysNTC BaseBox. Other models from
for details. the InteliGen and InteliSys range are also compatible
Optional 2) Compatible only with ID-DCU Marine from HW version 2.0 with this product, please visit www.comap-control.com
of the controller for more details.
3) Compatible only with InteliDrive Mobile Drive DCU: InteliDrive DCU Industrial, InteliDrive DCU Marine
from SW version 2.6.0 of the controller Mobile / Bifuel: InteliDrive Mobile, InteliBifuel
Comparison tables 83
Mains protection
InteliPro InteliPro SYNC MainsPro MainsPro Lite
ANSI
Under/overvoltage and asymmetry (two stage setting) 27, 59, 47 • • • •
Overfrequency, Underfrequency (two stage setting) 81H, 81L • •1) • •
Vector Shift 78 • – • –
ROCOF 81R • – • –
Instantaneous over current, Time over current 50, 51 • •1) – –
Current asymmetry 46 • – – –
Earth fault current 50N + 51N • •1) – –
Ground surge current 50GS + 51GS • •1) – –
Directional/Reverse power with time delay 32 • • – –
Breaker failure • • • •
Phase sequence supervision • – • •
Auto fault reset • • • •
Battery voltage protection • • • •
Synch Check 25 •1) • – –
Time over current with voltage control 51V •1) – – –
KEY • Included 1) Optional feature, activation via ComAp application. Please contact your nearest ComAp distributor
– Excluded to get more information.
86 Comparison tables
Communication and extension modules
Mobile /
ATS Lite Compact Gen / Sys InteliPro Drive DCU
Bifuel
CM-4G-GPS 4G Modem / Wireless Internet Module – •1) – – – – –
CM-Ethernet Internet / Ethernet Plug-in Module including Web Server – •1) – – – – –
CM-GPRS GSM Modem / Wireless Internet Module – •1) – – – – –
CM-RS232-485 Dual Port Extension Board – •1) – – – – –
I-CR CAN Repeater Module – – – • – • –
Communication
KEY • Included ATS: InteliATSNT Gen / Sys: InteliGenNT, InteliGenNT BaseBox, InteliGenNTC BaseBox,
– Excluded Lite: InteliLiteNT AMF 25, InteliLiteNT MRS 16, InteliDrive Lite. InteliSysNT, InteliSysNTC BaseBox. Other models from the
1) The product is suitable only for new generation of Other models from the InteliLiteNT and InteliDrive Lite InteliGen and InteliSys range are also compatible with
InteliLite models: InteliLite MRS 11, InteliLite MRS 16, range could be also compatible with this product, please this product, please visit www.
InteliLite AMF 20, InteliLite AMF 25 visit www.comap-control.com for more details. comap-control.com for more details.
2) The product is suitable only for selected models from Compact: InteliCompactNT Drive DCU: InteliDrive DCU Industrial, InteliDrive DCU Marine
the InteliLiteNT and InteliDrive Lite range. Please visit Mobile / Bifuel: InteliDrive Mobile, InteliBifuel
www.comap-control.com for more details.
Comparison tables 87
88
About
ComAp
ComAp is a dynamic international company with a solid reputation for
delivering innovative electronic solutions to the power generation, industrial
engine and equipment markets. By providing customers with state-of-the-art
products, ComAp has built a name for delivering excellent reliability and
good value.
ComAp
numbers
11
More than
90
400+
91
Close to our customers
To address specific needs
Our culture of excellence delivers consistently high standards of technical support to customers locally,
enabled by our global expertise.
Our focus on local presence and being close to our customers is a clear differentiator in our industry.
We’re leading the way in providing intelligent electronic control products and solutions that are highly
flexible, intuitive and scalable.
92
Our culture of excellence attracts
the very best people
We have freedom and support to create and deliver innovative electronic control solutions.
93
ComAp Subsidiaries
and Distributors
ComAp subsidiary
ComAp distributor
94
To find information about your local ComAp office please visit
www.comap-control.com/contact-us
95
Training centre Technical support
Learn more about our products Our technical support specialists will
The ComAp state-of-the-art Training Centre in Prague, help you to solve your requests.
Czech Republic allows ComAp customers unrivalled use and
access to ComAp products in a modern purpose built facility. The
centre has been designed for both theoretical classroom-based
training sessions, and also practical experience based training
24
using the latest ComAp products on operational gen-sets.
hours
96
Notes
97
98
99
02/2019