Professional Documents
Culture Documents
STRUTFAST
Cable Management Solutions
METAL FRAMING
METAL FRAMING
Load Ratings
Allowable slip out, pull out and load ratings for the metal framing product range have been
derived by calculation based on ultimate load capacity prior to product failure incorporating a
1.5 factor of safety. Metal framing is typically used in either a support beam or support column
arrangement.
Support Beam technical data lists maximum allowable uniform load and mid span deflection
at various spans. Together with this data, a loading to span was designated which will give a
deflection ratio of 1/200 of the span. This will give a recognized practical beam deflection to
minimize sagging of the beam under load.
Support Column technical data lists maximum lateral loading at a range on unbraced heights.
www.strutfast.co.za
1 ISO 9001:2015
METAL FRAMING
Safety Factor of 2
1 2 3
5
4
www.strutfast.co.za
2 ISO 9001:2015
www.strutfast.co.za I ISO 9001:2015 11
METAL FRAMING
Made to order
F1001A F1001B F1001C F1001-C4 F1001D
www.strutfast.co.za
3 ISO 9001:2015
METAL FRAMING
Section Properties
SAFE WORKING LOAD ON COLUMN APPLIED AT THE CENTROID OF THE SAFE WORKING
UNBRACED LOAD APPLIED
COLUMN HEIGHT SECTION, FOR DIFFERING COLUMN END CONDITIONS AT OPENING
mm OF THE CHANNEL
K = 0.8 K = 10 K =12 SECTION
* KL
r exceeds 200
www.strutfast.co.za
4 ISO 9001:2015
www.strutfast.co.za I ISO 9001:2015 11
METAL FRAMING
Cantilever Brackets
The Cantilever Bracket system is manufactured from mild steel and utilises F1000 channels welded to a back plate. All cantilever
support arms for cable ladders and trays should be 50mm longer than the width of the cable ladder or tray used. The safe
working load for cantilever arms is uniformly distributed over the length of the cantilever support arm. Standard Finish on
Cantilever Brackets is Hot Dip Galvanised.
www.strutfast.co.za
5 ISO 9001:2015
METAL FRAMING
General Fittings
Fittings
Standard Fittings form an integral part of the metal framing product. Various standard fittings allow the installer to quickly assemble
any solid structure to support cable management, condensers and piping, without requiring welding on site. An added advantage is
that it is easy to make adjustments, dismantle and re-use all components, as and when required.
All standard fittings are available in hot dip galvanized mild steel. Standard dimensions apply to all fittings, except where noted on the
part drawing and are subject to commercial tolerances.
Hole size 14mm diameter, Hole spacing 20.5mm from end of fitting, 48mm centre to centre. Fitting width 40mm and thickness 6mm
unless otherwise stated.
Post Bases
F2072/S1 F2858 F2073/A
128
64
64
135 180
80 100
100 100
Beam Clamps
F1271 F1272 F2785 F2786
‘U’ Fittings
F1377 F4377 F1047 F4047 F1737 F2346
83
186 186
98
137
137
137
137
‘Z’ Fittings
F1045 F4045 FZ01 FZ04
89 89
89
137
www.strutfast.co.za
6 ISO 9001:2015
www.strutfast.co.za I ISO 9001:2015 11
METAL FRAMING
General Fittings
Angular Fittings
F1026 F1033 F1034 F1035 F1068
90
137 90
43
47 57
51
48
47
89
105
89
105
105
89
67 64
67
102 94 80
98 51
F1546-45
60
76
Flat Fittings
F1036 F1028 F1066 F1031 F1065
137 137 89
89
135
89
183
138 40
90
www.strutfast.co.za
7 ISO 9001:2015