Professional Documents
Culture Documents
Learner’s Material
Department of Education
Republic of the Philippines
Technology & Livelihood Education– Grade 9
Learner’s Material
First Edition, 2013
ISBN:
Republic Act 8293, section 176 states that: No copyright shall subsist
in any work of the Government of the Philippines. However, prior approval of the
government agency or office wherein the work is created shall be necessary for
exploitation of such work for profit. Such agency or office may, among other
things, impose as a condition the payment of royalties.
Borrowed materials (i.e., songs, stories, poems, pictures, photos, brand names, trademarks, etc.) included in this book ar
Published by the Department of Education Secretary: Br. Armin A. Luistro, FSC Undersecretary: Dina S. Ocampo, Ph.D. As
Development
Authors:,Cris
Teacher I
Editors: Lando
Reviewers: Dr.
Marvin A. Mend
Illustrators:
Subject Specia
Management T
2
TABLE OF CONTENTS
TITLE PAGE
PECs ……………………………………………………………………………… 5
Environment and Market………………………………………………….. 21
Process and Delivery………………………………………………………… 33
Quarter I
Introduction ……………………………………………………………………… 33
Pre/Diagnostic LO1 …………………………………………………………….. 33
Information Sheet 1.1 ………………………………………………………….. 35
Self-Check 1.1 …………………………………………………………………… 37
Information Sheet 1.2 …………………………………………………………… 37
Self-Check 1.2 …………………………………………………………………… 42
Information Sheet 1.3 …………………………………………………………… 43
Self-Check 1.3 …………………………………………………………………… 45
Activity Sheet 1.1 ……………………………………………………………….. 46
Self-Check 1.1 …………………………………………………………………… 48
Activity Sheet 1.2 ……………………………………………………………….. 49
Self-Check 1.2 …………………………………………………………………… 51
Activity 1.3 ………………………………………………………………………. 52
Self-Check 1.3 …………………………………………………………………… 54
Pre/Diagnostic LO2 …………………………………………………………….. 56
Information Sheet 2.1 ………………………………………………………….. 56
Self-Check 2.1 …………………………………………………………………… 58
Activity Sheet 2.1 ……………………………………………………………….. 59
Self-Check 2.1 …………………………………………………………………… 61
Summative Assessment Quarter I ………………………………………….. 62
Quarter II
Introduction ……………………………………………………………………… 64
Pre/Diagnostic LO3 …………………………………………………………….. 64
Activity Sheet 3.1 ……………………………………………………………….. 65
Self-Check 3.1 …………………………………………………………………… 68
Pre/Diagnostic LO4 …………………………………………………………….. 69
Information Sheet 4.1 ………………………………………………………….. 70
Self-Check 4.1 …………………………………………………………………… 72
Activity Sheet 4.1 ……………………………………………………………….. 72
Self-Check 4.1 …………………………………………………………………… 73
Activity Sheet 4.2 ……………………………………………………………….. 74
Self-Check 4.2 …………………………………………………………………… 75
Summative Assessment Quarter II ………………………………………… 77
Quarter III
Introduction ……………………………………………………………………… 79
Pre/Diagnostic LO1 …………………………………………………………….. 80
Information Sheet 1.1 ………………………………………………………….. 81
Information Sheet 1.2 …………………………………………………………… 82
Self-Check 1.2 …………………………………………………………………… 86
Information Sheet 1.3 …………………………………………………………… 87
Self-Check 1.3 …………………………………………………………………… 92
Activity 1.1 ………………………………………………………………………. 93
Self-Check 1.1 …………………………………………………………………… 94
Pre/Diagnostic LO2 …………………………………………………………….. 95
Information Sheet 2.1 …………………………………………………………… 96
Self-Check 2.1 …………………………………………………………………… 103
Activity Sheet 2.1 ……………………………………………………………….. 103
Self-Check 2.1 …………………………………………………………………… 105
Activity Sheet 2.2 ……………………………………………………………….. 106
Self-Check 2.2 …………………………………………………………………… 107
Summative Assessment Quarter III ……………………………………….. 108
Quarter IV
Introduction ……………………………………………………………………… 110
Pre/Diagnostic LO3 …………………………………………………………….. 110
Information Sheet 3.1 …………………………………………………………… 111
Self-Check 3.1 …………………………………………………………………. 115
Information Sheet 3.2 ………………………………………………………… 116
Self-Check 3.2 …………………………………………………………………. 117
Activity Sheet 3.1 ……………………………………………………………… 117
Self-Check 3.1 …………………………………………………………………… 120
Information Sheet 3.3 ………………………………………………………… 122
Activity Sheet 3.2 …………………………………………………………….. 130
Self-Check 3.2 ………………………………………………………………….. 132
Pre/Diagnostic LO4 …………………………………………………………… 134
Activity Sheet 4.1 …………………………………………………………….. 134
Self-Check 4.1 ………………………………………………………………….. 135
Summative Assessment Quarter IV …………………………………… 136
Technical Terms …………………………………………………………….. 138
References …………………………………………………………………….. 141
Personal Entrepreneurial Competencies
Have you ever thought running your own business? Entrepreneurship has
brought great success to some, but it's not a career path for all. Do you think you
can handle the stress and hard work that go with running a small business
enterprise? The key to succeed in a small business enterprise is your
entrepreneurial ability to produce the desired results. Before embarking on your first
business, it's worth spending some time evaluating your own preparedness for
entrepreneurship. Try to examine your own personality and compare it with the
Personal Entrepreneurial Competencies (PECs) of a successful entrepreneur. Ask
yourself if you are ready to enter into the world of business. If your answer is yes,
take this reminder: “Successful entrepreneurs continuously develop and
improve their PECs”.
Essential Question
Content Standard
Guide Questions:
5. Based on the data that you have gathered from the interview with the
successful entrepreneur in your community, how do you develop your PECs?
Can you prepare an action plan that addresses your areas of development and strength based on your PECs?
How does your action plan help sustain your strong areas and or address your development areas based on your PECs?
e you ready to assess yourself to become a successful entrepreneur in the future? As honest as you could, please answer th
Pre- Assessment
A.Matching Type
Column A Column B
8. Committed
10. Risk-taker
u will do another set of pre- assessment which could give you a better understanding of what this module is all about. Are y
cribes the entrepreneurial characteristics or attributes. Answer the question by writing the letter of your choice in your assign
Mrs. Gina Magno opens up her own retail business. She knows that her
personal entrepreneurial characteristics are insufficient to ensure a successful
operationalization of a business that she has in mind. Your answers to the
questions below will help in developing her PECs.
1. What PECs must she possess if there are customers who complain about the
quality of her product?
a. Patience
b. Hardworking
c. Versatile
d. All of the above
2. Which of the following is NOT considered as a characteristic of an
entrepreneur?
a. Copes with failure
b. Dependent
c. Persistent
d. Opportunity seeker
3. If she wants to ensure a profitable business operation, what characteristic will
she maintain?
a. Commitment
b. Goal oriented
c. Futuristic
d. Opportunity seeker
4. Mrs. Magno follows the advice of a friend to be flexible especially if she intends
to open a retail business. What PECs has been demonstrated by Mrs. Magno?
a. Self- confidence
b. Reliable and has integrity
c. Open to feedback
d. Persistent
5. She tells Mary, her best friend that she has a strong will and does not give up to
find a solution to a business problem. What PECs has been demonstrated by
Mrs. Magno?
a. Hard work
b. Persistence
c. Self-confidence
d. Risk- taking
This time evaluate your own personal entrepreneurial
characteristics to determine whether you too, can become an
entrepreneur. If you are ready, you may begin!
C. Self- Assessment
Demonstrates initiative
Willing to listen
Sets own standards
Copes with uncertainty
Committed
Builds on strengths
Reliable and has integrity
Risk-taker
1. Hard working: If you are determined to run your own business, you must
concentrate on your work either as a producer or a seller. The success of
your business depends on how much time and effort you will spend on it.
2. Self- Confidence: You must have a strong faith in your ability despite the
problems that you will encounter along the way.
3. Future-Oriented: Once a person enters in a line of business, you must
understand that you are in a non-stop contract that an entrepreneur should
understand. It may take several years to build up a business to a reasonable
standard. The goal for most successful business people is to build a secure
job and stable income for themselves based on their own ability.
4. Profit-Oriented: When you enter into the world of business, obviously, you
are looking for income because you know that this will be your bread and
butter not only for you but also for your family. Therefore, you must see to it
the business can generate income. Another plan of action is to expand your
own business through the use of your generated income.
5. Goal-Oriented: An entrepreneur is forward looking. You have an advanced
preparation for your business. You set a long-term goal for the activities that
are needed, an extensive preparation for the production process and
procedures that you need to go through to acquire, human and non-human
resources. Everything in your business will have to be set clearly, organized,
and planned depending on the goal you want to achieve.
6. Persistence: Differences in opinion and judgment. Your opponent can be a
part of the rejection on what you intend to do for your endeavor. As an
entrepreneur, you must be firm, strong-willed, and stick or follow your own
belief.
7. Copes with Failure: “Learn from your mistakes”. As an entrepreneur, you
must learn how to deal with the frustrations and failures instead, turn these
into productive learning experiences.
8. Responds to Feedback or Open to Feedback: You must be concerned to
know how well you are doing and keep track of your performance. You must
obtain useful feedback and advice from others.
9. Take the Initiative: A successful entrepreneur takes the initiative. You must
put yourself in a position where you personally are responsible for the failure
or success of your business.
10. Willing to Listen: Take time to listen to the advice, suggestions, and
recommendations of fellow entrepreneurs. It will help your business grow.
11. Set your Own Standards: This involves developing and using logical, step-
by-step plans to reach the goals, or offering evaluation alternatives,
monitoring progress, and switching to successful strategies for the goal you
want to achieve. To be a successful entrepreneur you must take into
consideration that sales and production depend on your own standards.
12. Copes with Uncertainty: Pursue your vision to be a successful
entrepreneur, you should know how to handle unusual events that may
happen in the business which include problems in managing the workers,
problems on the delivery of goods and services, and the problems on
demand and production. You must be patient in dealing with these
uncertainties.
13. Committed: You should know that in your business, personal needs,
attachment to your friends, families and relatives are set aside. You must
separate the money for your business from the amount that you need to
spend for personal obligations and lifestyles.
14. Builds on Strengths: Successful business people base their work on
strengths. Use your manual skills, knowledge in creating products or
services, knowledge in trade and industry, ability to make and use of a wide
network of contacts to build your business.
15. Reliable and has Integrity: An entrepreneur must build a good reputation,
possess the courage to do the right thing, do what you say, walk your talk, be
loyal, and be fair in dealing with the subordinates and costumers.
16. Risk-Taker: Risk sometimes cannot be anticipated. When misfortunes
happen, consider these as challenges and work them out and set good
alternatives. Risks may result to loss of your business or even bankruptcy.
Directionss: Choose from the list below the characteristics and traits that best
describe your own personal entrepreneurial characteristics. Find
ways on how to align them according to the personal entrepreneurial
characteristics of an entrepreneur which were discussed earlier.
Write your answer onthe activity sheet provided.
Example: My PECs
sign a concept map that indicates your traits, characteristics and skills that you need to possess in order to become a succe
arrows where positive and negative characteristics and traits are written. Pick out the positive PECs that you are already str
s at the right side are the
ce again reminding you whether you have achieved a certain point that you could honestly tell that you are already success
Directionss: From the given chart below, write at least six techniques on how you
would strengthen your own PECs. Write the PECs that you feel that you still need to focus on to strengthen these.
Example: Self-confidence
TRANSFER Your Learning
Preparation of an Action Plan Culminating Activity
Directionss: Examine yourself once again. Make a short list of PECs that you need to strengthen. From
Sample Action Plan
of Recognition
Area Situation Goal Required Frame
Success
My PECs I need to - To exercise Achieve -Selling -During -Earns
develop my my own finished culminating expected
undefined 100% products activities income
characteris- PECs during completion of derived from
tics need for selling and development culminating -After -Outstanding
producing of my own activities in learning performance
my retail
products/ PECs through any of chosen in selling and
the promoting
business. such services selling and career.
principles,
as: production of products and
-To become products, -Participate services
theories,
proficient in proper
process
my chosen manner when in skills
skill. and of any
dealing with
competition chosen
people.
career
sponsored by
the NGO and
GO
Post-Assessment
A. Matching Type
Column A Column B
8. Committed
10. Risk-taker
B. Multiple Choice.
Mrs. Gina Magno opens up her own retail business. She knows that her
personal entrepreneurial characteristics are insufficient to ensure a successful
operationalization of a business she has in mind. Your answers to the questions
below will help in developing her PECs.
1. What PECs must she possess if there are customers who complain about the
quality of her product?
a. Patience
b. Hardworking
c. Versatile
d. All of the above
2. Which of the following is NOT considered as a characteristic of an
entrepreneur?
a. Copes with failure
b. Dependent
c. Persistent
d. Opportunity seeker
3. If she wants to ensure a profitable business operation, what characteristic
will she maintain?
a. Commitment
b. Goal oriented
c. Futuristic or future-oriented
d. Opportunity seeker
4. Mrs. Magno follows the advice of a friend to be flexible especially if she
intends to open a retail business. What PECs has been demonstrated by
Mrs. Magno?
a. Self- confidence
b. Reliable and has integrity
c. Responsive to feedback
d. Persistent
5. She tells Mary, her best friend that she has a strong will and does not give up
to find a solution to a business problem. What PECs has been demonstrated
by Mrs. Magno?
a. Hard work
b. Persistence
c. Self-confidence
d. Risk- taking
Feedback
A. Matching Type
1.d 6. f
2.c 7. e
3.b 8. j
4.a 9. i
5.g 10. h
B. Multiple Choice
1. a
2. b
3. d
4. c
5. b
Environment and Market
Essential Question
How does one select an entrepreneurial activity?
Content Standard
Performance Standard
u ready to assess yourself if you are ready to generate potential business ideas? Let’s try by answering the succee
Pre-assessment
e following should be considered first by a prospective entrepreneur in choosing the right location for his/her stor
erchandise
he target customers
veness of the store layout
ing prices of goods in the area
Everyone has his or her own needs and wants. However, people have
different concepts of needs and wants. Needs in business are important
things that every individual cannot do without in a society. These include:
Wants are desires, luxury and extravagance that signify wealth and an
expensive way of living. Wants or desires are considered above all the basic
necessities of life. Some examples are the eagerness or the passion of every
individual which are non- basic needs like; fashion accessories, shoes,
clothes, travelling around the world, eating in an exclusive restaurant;
watching movies, concerts, plays, having luxurious cars, wearing expensive
jewelry, perfume, living in impressive homes, and others.
Needs and wants of people are the basic indicators of the kind of
business that you may engage into because it can serve as the measure of
your success. Some other good points that you might consider in business
undertakings are the kind of people, their needs, wants, lifestyle, culture and
tradition, and social orientation that they belong.
Here are some ways by which you may generate possible ideas for business.
1. Examine the existing goods and services. Are you satisfied with
the product? What do other people who use the product say about it?
How can it be improved? There are many ways of improving a product
from the way it is made to the way it is packed and sold? You can also
improve the materials used in crafting the product. In addition, you
introduce new ways of using the product, making it more useful and
adaptable to the customers’ many needs. When you are improving the
product or enhancing it, you are doing an innovation. You can also do
an invention by introducing an entirely new product to replace the old
one.
2. Examine the present and future needs. Look and listen to what the
customers, institution, and communities are missing in terms of goods
and services. Sometimes, these needs are already obvious and felt at
the moment. Other needs are not that obvious because they can only
be felt in the future, in the event of certain developments in the
community. For example, a town will have its electrification facility in
the next six months. Only by that time will the entrepreneur could think
of electrically- powered or generated business such as xerox copier,
computer service, digital printing, etc.
3. Examine how the needs are being satisfied. Needs for the products
and services are referred to as market demand. To satisfy these
needs is to supply the products and services that meet the demands of
the market. The term market refers to whoever will use or buy the
products or service, and these may be people or institutions such as
other businesses, establishments, organizations, or government
agencies.
Businesses or industries in the locality also have needs for goods and
services. Their needs for raw materials, maintenance, and other
services such as selling and distribution are good sources of ideas for
business.
Business ideas can come from your own skills. The work and
experience you may have in agricultural arts, industrial arts, home
economics, and ICT classes will provide you with business
opportunities to acquire the needed skills which will earn for you extra
income, should you decide to engage in income-generating activities.
With your skills, you may also tinker around with various things in your
spare time. Many products were invented this way.
People keep on searching for new things, new trends, and new
issues. For these reasons, an entrepreneur hurriedly responds to these
needs and wants of people.
As generations come and go, another set of new trends will
come or will exist. In order to adapt to the rapid changes in the
business environment, the existing industries need to improve their
products and services. But how can you generate business ideas with
those strong competitors? There are three main sets of decisions that
you need to make - what to produce, how to produce, and how to
share or sell out the product to the market.
Directionss: After filling out the chart above, try to list down all the probable
business opportunities which you may wish to venture in. Remember to
consider the ideas and suggestions discussed in Lesson 3. Use the
suggested matrix below to indicate your choice. Write your answer onyour
notebook.
Positive Factors
Negative Factors
TRANSFER Of Learning
Now that, you have all the information, are you ready to test
your ability to generate your own business idea? If your answer is yes,
start studying the sample vicinity map of a community with a population
of two thousand people. A new housing project will be constructed
adjacent to Daang Hari St, close to Old Molino St., its main road. This
housing project targets the homeowners who are young couples with
two kids.
In this activity, you need to answer the questions that may lead to
the generation of a probable business. Your answers to these
questions will serve as the bases in formulating your own business
ideas.
Post-assessment
Feedback
1. a
2. b
3. d
4. c
5. b
Process and Delivery
I. INTRODUCTION:
Directionss: Read each statement carefully and select the letter of the
correct answer. Write your answer on a separate sheet of paper.
1. It refers to a handtool that is used in holding, gripping, and cutting
of soft and fine wires in assembling electronic circuit?
A. Pliers B. Scissor C. Tweezers D. Vise grip
10. What is the stage of the power supply that reduces the amount of
ripple voltage and smoothen the pulsating DC output voltage of
rectifier circuit?
A. Bleeder B. Filter circuit
C. Rectifier circuit D. Step-down transformer
INFORMATION SHEET 1.1
Soldering tools:
Soldering iron
Soldering lead
Desoldering tool
Soldering stand
Screwdriver
1. Flat head
2. Philip
1. 2.
1.
Pliers 2.
1. Diagonal cutting pliers
2. Long nose pliers
1. 2.
1. Wire stripper
2. Utility knife
Boring tools
Mini drill with power
supply
Drill bit (in proportion
with terminals of
component)
Multitester/ Volt-Ohm-
Milliammeter (VOM)
Analog
Copper clad
Sand paper
Pencil and paper
Ruler
Masking tape
Cleaning brush
Cleaning agent
Permanent marker
1 2 3 4 5
6 7 8 9 10
11 12 13 14 15
t power from grid line to DC output voltage (AC-DC). It supplies the desired voltage and current in a circuit. Without these, all electroni
A basic power supply consists of three basic stages: the power
transformer stage, rectifier stage, and filter stage. If there is a need to
regulate the output voltage, a regulator circuit is added.
Transformer stage
There are two types of rectifier, Half-wave Rectifier and the Full-wave
Rectifier. Under a Full-wave rectifier, there are two types, the Center-tapped
and the Bridge Rectifier.
uction
tive half-cycle will be conducted to the cathode of diode D1, and then thru the RL it will conduct to the cathode of diode D4 goes to Lin
ase D1 and D4 are conducting.
Second Conduction
Filter Stage
Placing additional
capacitor in the output.
Filter Circuit
Placing a resistor
in series with the
positive line can
cause voltage
drop.
SELF-CHECK 1.2
AC-DC POWER SUPPLY
II. Directions: Draw the schematic diagram of bridge type rectifier circuit:
(for five points)
Criteria Points
Complete components/ correct connection/ with label/ correct symbols 5
Complete components/ correct connection/ no label/ correct symbols 4
Complete components/ correct connection/ no label/incorrect symbol 3
Complete components/ incorrect connection/ no label/incorrect symbols 2
Complete components/ incorrect connection/ no label/incorrect symbols 1
INFORMATION SHEET 1.3
PRINTED CIRCUIT BOARD OF AC-DC POWER SUPPLY
Copper
Substrate
Copper Clad
1. PCB size and shape. The PCB must be big enough for the entire
component to be mounted on a specific area.
5. Space for Bolt and Nut. The designer should place a good space for
mounting the PCB with bolt and nut in securing the entire board
to the chassis.
Copper/Conductor
Substrate
Tools and Materials Needed In PCB Etching
SELF-CHECK 1.3
PRINTED CIRCUIT BOARD OF AC-DC POWER SUPPLY
Directions: Read each statement and write the term being described in each
number on your answer sheet.
Note: If you got all the answers right, that is an excellent mark. If you missed
one or more item/s, go back to information sheet 1.3, review the questions,
and study them more closely. Before you proceed to the next lesson you must
get all the answers right.
ACTIVITY SHEET 1.1
DESIGNING AND PREPARING PCB OF AC-DC POWER SUPPLY
Directionss: Given the resources needed, the students will design and
prepare a PCB of AC-DC Power Supply individually by following the
procedures given. After the activity, the students output will be graded
through the given Performance Check.
Resources:
5. Trace the reverse side of the designed PCB by using a carbon paper and
mark it on the copper side of the clad board.
Directions: Read the criteria in the box and check the box if you performed
the item. A check is equivalent to one point.
Criteria Performed
Resources:
Before proceeding, the students should prepare the following:
Ferric Chloride
Plastic
4. Etch the PCB by immersing it in a basin filled with ferric chloride until
the uncovered part of the copper clad is totally etched.
PCB
5. After 10 - 15 minutes, check the PCB if all the parts needed to be
removed are totally etched (using the two popsicle sticks in hauling).
If there are still unnecessary copper, return it into the plastic basin
filled with ferric chloride and check it again after 3 – 5 minutes.
6. Haul the PCB from the plastic basin and wash with running water to
remove the remaining etching solution and other residues.
7. Dry PCB with a clean piece of cloth.
8. Pour a little amount of lacquer thinner on a clean dry piece of cloth
and wipe the markings of the permanent marker in the copper clad.
(Note: In doing this, you should still wear surgical gloves.)
9. Aided by bright light, inspect the PCB for possible hairline break or
short. If there is a hairline path between the copper conductors, cut it
by a knife or cutter. If there is a break between the copper conductors,
solder it.
SELF-CHECK 1.2
PCB ETCHING
Directionss: Rate yourself on how competently you have applied the skill in
PCB Etching using the criteria below by checking on the appropriate
box (points 1 to 5, 5 being the highest). Compute for the rating by
dividing each item by 5, multiply by 100. Average the rating of the six
criteria to get the final rating.
Points
Criteria 5 4 3 2 1 Rating
Workmanship
Use of Tools
Use of Personal Protective Equipment
SPEED
House Keeping
Finished Design
Total
Criteria Description
Followed the steps accordingly/ Less 1 point for
Workmanship
every missed procedure.
Used tools/ materials in right task/ Less 1 point for
Use of Tools
every misused.
Use of Personal Used PPE during the whole activity/ Less 1 point for
Protective Equipment every forgotten instances
Finished within the time/ Less 1 point for every five
SPEED
minutes delay
The workplace is clean before, during and after the
House Keeping
activity/ Less 1 point for every dirt observed
Neat and presentable output and / Less 1 point for
Finished Design
every unusual marks at the output
Resources:
1.2 Insert the drill bit 1mm diameter in size and attach it to
the chuck of the unit.
1.3 Turn the precision screwdriver clockwise to tighten the jaw
of the unit. Be sure that the drill bit is well secured on the
chuck.
1.4 Before inserting the 12 volts adaptor, you should turn off
the unit.
1.5 Test the rotation of the unit if it is well aligned. If not, align it
following steps no. 1 and 2.
To control the unit, hold the mini drill at the lower part and
firmly position your arm. Then with the mini drill held
perpendicularly to your work surface, lightly press downward to the
holes to be drilled in the PCB but be sure that the PCB has a piece of
wood under it to avoid damaging the table. With practice, you will be
able to get the procedure correctly.
53
3. Boring Procedure
SELF-CHECK 1.3
BORING ETCHED PCB OF AC/DC POWER SUPPLY
Directionss: Rate yourself on how competent you have applied the skill in
Boring etched PCB using the criteria below by checking on the
appropriate box (points 1 to 5, 5 being the highest). Compute for the
rating by dividing each item by 5, multiply by 100. Average the rating of
the six criteria to get the final rating.
Points
Criteria 5 4 3 2 1 Rating
Workmanship
Use of Tools
Use of Personal Protective Equipment
SPEED
House Keeping
Finished Design
Total
5
4
Criteria Description
Followed the steps accordingly/ Less 1 point for every
Workmanship
missed procedure.
Used tools/ materials in right task/ Less 1 point for every
Use of Tools
misused.
Use of Personal Used PPE during the whole activity/ Less 1 point for every
Protective Equipment forgotten instances
Finished within the time/ Less 1 point for every five
SPEED
minutes delay
The workplace is clean before, during and after the
House Keeping
activity/ Less 1 point for every dirt observed
Neat and presentable output and / Less 1 point for every
Finished Design unusual marks at the output
V. PRE/DIAGNOSTIC ASSESSMENT
The internal parts of the power supply are shown in the figure below.
58
ACTIVITY SHEET 2.1
MOUNTING AND SOLDERING COMPONENTS OF AC-DC POWER
SUPPLY
Directions: Using the given tools, supplies and materials, mount the
electronic components to the finished PCB and perform soldering
techniques to assemble rectifier circuit of an AC-DC power supply.
Read some information and follow the instruction/ procedures
given. Assessment checklist will be used to rate the performance.
Resources:
o Supplies and Materials
- Designed PCB
- Soldering Lead, 60/40
- 4 pcs. Rectifier diode- 1N4001
- Electrolytic capacitor – 3,300 uF/25V
- Jumbo LED with holder
- Resistor- 1KΩ, 5 watts
- Schematic diagram of AC/DC Bridge-type power
supply
- Design of AC/DC Bridge-type power supply (copper
side and component placement guide)
o Tools andEquipment
- Soldering tools
- Pliers
AC/DC Unregulated Multi-secondary Power Supply
59
Procedures:
Working area set with tools, instrument and materials needed in mounting and
soldering components of ac-dc power supply.
Mounting of components
6
0
SELF-CHECK 2.1
Mounting and Soldering Components of AC-DC Power Supply
Project
Directionss: Rate yourself on how competently you have applied the skill in
PCB Etching using the criteria below by checking on the appropriate
box (points 1 to 5, 5 being the highest). Compute for the rating by
dividing each item by 5, multiply by 100. Average the rating of the six
criteria to get the final rating.
Points
Criteria 5 4 3 2 1 Rating
Workmanship
Use of Tools
Use of Personal Protective Equipment
SPEED
House Keeping
Finished Design
Total
Criteria Description
Followed the steps accordingly/ Less 1 point for every
Workmanship
missed procedure.
Used tools/ materials in right task/ Less 1 point for
Use of Tools
every misused.
Use of Personal Used PPE during the whole activity/ Less 1 point for
Protective Equipment every forgotten instances
Finished within the time/ Less 1 point for every five
SPEED
minutes delay
The workplace is clean before, during and after the
House Keeping
activity/ Less 1 point for every dirt observed
Neat and presentable output and / Less 1 point for
Finished Design
every unusual marks at the output
Rating System for Self-Check 2.1
1. A tool used to join two our more metal parts by melting lead.
A. Screw Driver B. Soldering Iron
C. Long Nose Pliers D. Multitester
2. A device used to measure voltage, current and resistance.
A. Ammeter B. Long nose pliers
C. Multitester D. Screwdriver
3. A type of rectifier circuit which uses four diodes.
A. Half-Wave B. Full-Wave
C. Full-Wave Center Tapped D.Full-Wave Bridged
4. In PCB designing bigger space is required so that heat sink can be
installed, what design factor is being considered?
A. PCB size and shape.
B. Position of the terminal.
C. High Temperature Dissipation
D. Accessibility of Components.
E. Space for Bolt and Nut.
5. The removal of unnecessary portion or layer of conductive material of
PCB. A. Boring/Drilling B. Etching
C. Soldering D. Tracing
I. INTRODUCTION:
Directions: Prepare/ check the materials, tools and instrument listed in the
resources. A schematic diagram is provided for your reference in
interconnecting the auxiliary components. You will be given one hour for
this activity. Follow the given instructions and your work will be graded
using the scoring rubrics 3.1.
Resources:
Directionss: Rate yourself on how competent you have applied the skill in
Interconnecting Auxiliary Components of AC/DC Power Supply using
the rubrics below. Each criterion has indicators and corresponding
points that will guide you in rating your performance. Add the rating to
get your total score.
Criteria Rating
Workmanship
Accuracy
SPEED
House Keeping
Total
SCORING RUBRICS
CRITERIA SCORE
Workmanship 45 points
Proper tools were used according to their function; PPE and OHS 45
were observed while working.
Proper tools were used according to their function; PPE were 40
observed but some OHS were ignored
Proper tools were used according to their function; PPE were not 35
observed and some OHS were ignored
Tools were not used properly; PPE and OHS were observed 25
Some tools were not used properly; some PPE and OHS were ignored 15
Accuracy 45 points
Auxiliary components and PCB were mounted properly; Wires were 45
arranged accordingly; Indicator light (AC and DC) function; Output voltage
are in increasing order.
Auxiliary components and PCB were mounted properly; Wires were 40
arranged accordingly; Indicator light (AC and DC) function; Output voltage
are not in order but of correct value.
Auxiliary components and PCB were mounted properly; Wires were 30
arranged accordingly; Indicator light (AC and DC) malfunction; Output
voltage is not of correct value.
Auxiliary components and PCB were mounted properly; Wires were not 25
arranged accordingly; Indicator light (AC and DC) malfunction; Output
voltage is not of correct value.
Auxiliary components and PCB were not mounted properly; Wires were not 15
arranged accordingly; Indicator light (AC and DC) malfunction; Output is
not of correct value.
Auxiliary components and PCB were not mounted properly; Wires were not 10
arranged accordingly; Indicator light (AC and DC) malfunction; Output
voltage are not achieved.
Speed 5 points
Finished task before time frame 5
Finished task 15 minutes after the time frame 4
Finished task 30 minutes after the time frame 3
Finished task 31 minutes and more 2
Housekeeping 5 points
The whole area was cleaned before and after the assembly 5
The whole area was dirty at the start but cleaned after the assembly 4
The whole area was cleaned before the assembly but left dirty after 3
The area was dirty before and after the assembly process 1
TOTAL 100%
Rating System
Score Descriptive Grade
95- 100 Outstanding
80 - 94 Very Satisfactory
75 – 79 Satisfactory
74 and below Needs Improvement
Components of 5s
SORT : Identify and separate necessary items from the unnecessary by (a)
Segregating useful from non-useful items; (b) Recycling items; (c)
Disposing properly non-useful items (bio-degradable or non-
biodegradable)
Procedures:
STEP 1: Look around your workplace with your colleagues. Identify
items which are unnecessary to your work. Start with a RED TAG
CAMPAIGN. Decide the maximum number of any type of item to be
retained. Then dispose ALL unnecessary items.
STEP 2: A Disposal Notice with a date can be done to an item that
you cannot decide if it is necessary or not, and set the item aside.
After a period of time, check if no one needed the item. If no one
needed the item, disposal can be done.
SELF-DISCIPLINE
Instilling the ability of doing things the way they are supposed to be
done; becoming a role model by treating your school as your second
home; influencing others to join in keeping a well-maintained study
area; aiming for constant improvement; do things spontaneously
without being told or ordered is to make everyone practice 4S
WILLINGLY and spontaneously as a habit or way of life. There is no
other way to foster such culture than practicing 4S regularly
until such time when everyone becomes FOND of 5S. Self-discipline
is a good tradition.
SELF-CHECK 4.1
5S
Directions: Read each statement and write the term being described in each
number on your answer sheet.
Resources:
5s principles
Activity sheet (Student write-up)
Designated area for each group
SELF-CHECK 4.1
5s
Directions: Rate yourself on how competently you have applied the skill in
5s using the criteria below. Checking on the appropriate box (points 1
to 5, 5 being the highest). Compute for the rating by dividing each item
by 5, multiply by 100. Average the rating of the five criteria to get the
final rating. A deduction of 1 for everything missed.
Rating
Criteria Description 5 4 3 2 1
Arrange the items in the assigned work
Sorting
area
The materials/ things in the area was
Systematize properly labeled and in proper
sequence
The area was clean (floor/ ceilings/ all
Sanitize
things free from dirt/ dust/ moisture)
Finished within the time/ Less 1 point
Speed
for every five minutes delay
Workmanship Group cooperation was observed
Rating System
Score in Percent Descriptive Grade
95% - 100% Outstanding
80% - 94% Very Satisfactory
75% - 79% Satisfactory
74% and below Needs Improvement
ACTIVITY SHEET 4.2
TESTING THE FINISHED AC-DC POWER SUPPLY
Directionss: Provided with necessary tools and instrument, the student will
now test the finished power supply in accordance with quality standards.
Follow the procedures given to finish this job.
Resources:
Finished Power Supply
Measuring Instrument (Multitester)
Activity sheets
Schematic Diagram
Procedure in Testing the Finished Power Supply
1. Inspect the mounting of the PCB, transformer, rotary switch, and other
auxiliary components if it is fixed properly.
2. Check the connection of wires for good solder and proper connection in
accordance with the schematic diagram.
3. With the use of multitester (set at range X 1), check the resistance from
the AC plug (switched “ON” and “OFF”) and the resistance at the alligator
clip (rotating the selector switch). It is a must that no short circuit reading
will be encountered. If this happen, do not attempt to energize your
project until the problem is solved.
4. If everything is okay, plug the unit to AC outlet, make sure that the power
switch is turned off.
5. Turn the power switch “ON”. The neon lamp and LED must light.
6. Rotate the selector switch and stop at its full left turn.
7. Measure the output voltage:
7.1 Set the multitester at range setting 50 V DC (the assumed
maximum voltage is around twelve volts)
7.2 Connect the test probe to the alligator clip observing the polarity.
7.3 Read the voltage at the full left then record it, then rotate the
selector once to the right, then read again until to the last set of
the selector.
8. For reference purposes, measure the supply AC voltage at the primary
and the secondary voltage. Record the readings.
Note: ensure meter is set to AC. Observe safety when measuring AC voltage.
9. Fill Table 4.1 (Reference Voltage Measurement) with the measured voltage
at the primary and output terminals for future references.
10. If necessary, take a picture of the finished AC/DC Power Supply for
documentation purposes. Keep the design with the schematic diagram
and the reference voltages for future use.
11. Practice the principle of 5s at all times.
Table 4.2 Reference Voltage Measurement
AC/DC Power Supply
Name:
Date Performed:
SELF-CHECK 4.2
TESTING THE FINISHED AC-DC POWER SUPPLY
Directionss: Rate yourself on how competently you have applied the skill in
testing the finished AC-DC power supply using the criteria below by
checking on the appropriate box (points 1 to 5, 5 being the highest).
Compute for the rating by multiplying the score by the corresponding
percentage of every criterion. Add the four ratings to get the final
rating.
Score
Criteria % 5 4 3 2 1 Rating
Workmanship 45
Accuracy 45
SPEED 5
House Keeping 5
Total 100
Workmanship 45%
1. Conduct continuity test accordingly before energizing the unit; Followed 5
the Procedure.
2. Conduct continuity test on higher setting range before energizing the unit; 4
Followed the procedure .
3. Conduct continuity test accordingly before energizing the unit; Disregard 3
the testing procedure.
4. Conduct continuity test on higher setting range before energizing the unit; 2
Followed the testing procedure .
5. Did not conduct continuity test and disregard the testing procedure. 1
Accuracy 45%
1. Measured proper sequence of voltages using appropriate setting range. 5
2. Measured proper sequence of voltages using one setting range. 4
3. Measured proper sequence of voltages using inappropriate setting range. 3
4. Measured output voltages in random using one setting range. 2
5. Measured output voltages in random using inappropriate setting range. 1
Speed 5%
1. Finished task before time frame (ten minutes time allotment) 5
2. Finished task 3 minutes after the time frame 4
3. Finished task 5 minutes after the time frame 3
4. Finished task 15 minutes and more 2
Housekeeping 5%
1. The whole area was cleaned before and after the activity 5
2. The whole area was cleaned before the activity but dirty after 4
3. The whole area was dirty at the start but cleaned after 3
4. The area was dirty before and after the activity. 2
Rating System
Score in Percent Descriptive Grade
95% - 100% Outstanding
80% - 94% Very Satisfactory
75% - 79% Satisfactory
74% and below Needs Improvement
VI. Summative Assessment
I. Directions: Identify what component of 5S are shown in the following:
1. Neat placement and identification of needed items by studying them the
frequency of their use.
2. Identify and separate necessary items from the unnecessary by
segregating useful from non-useful items.
3. Instilling the ability of doing things the way they are supposed to be done.
4. Maintaining a clean work place.
5. Maintain high standard of housekeeping or equipment cleaning
and checking procedures.
II. Multiple Choice. Write only the letter of the best answer.
Directionss: Prepare/ check the materials, tools and instrument listed in the
resources. A schematic diagram is provided for your reference in
interconnecting the auxiliary components. You will be given one hour for
this activity. Follow the given instructions and your work will be graded
using the following scoring rubrics.
I. INTRODUCTION:
This module consists of four (4) learning outcomes which will help teach
the maintenance and repair of electronically-controlled domestic appliance
(blender and electric fan). Each learning outcome contains information and
learning activities supported by self-check. Before you perform the
instructions, read the information sheets and answer the self-check and
activities provided to ascertain to yourself and your teacher that you have
acquired the knowledge necessary to perform the skill portion of the
particular learning outcome. Procedure in pre-testing Electronically-
Controlled Electric Fan (ECEF) and Blender are included to address the
requirements to complete the lesson.
I. Directions: Read each statement carefully and select the term being asked.
Write your answer on a separate sheet of paper.
Soldering tools:
Soldering iron
Soldering lead
Desoldering tool
Soldering stand
Screwdriver
Flat head
Philip
Pliers
Diagonal cutting pliers
Long nose pliers
Wire stripper
Utility knife
Multitester/ Volt-Ohm-
Milliammeter (VOM)
Analog
PPE
EDS wrist strap
Mask
Apron
Non-static brush
Cable tie
Combination wrench
Adjustable plier
A blender is…
a motorized small kitchen
appliance that blends, chops,
and grates food.
a handy electrical gadget that
makes chopping and mixing
food easier.
a liquidizer or kitchen appliance
used to mix ingredients or make
puree.
a stationary, upright electrical
device which is distinguished
from a hand-powered or electric
mixer that may be used for
similar purposes.
A blade inside a jar is connected to a motor shaft inside the unit. The
blade speed is controlled by varying electric current at the motor using one
or more switches.
Blenders are used both at home and commercial kitchens for various
purposes:
to crush ice in drinks;
to make smooth purées of semi-solid ingredients such as
cooked vegetables and meat;
to reduce small solids such as spices and seeds to powder
or nut butters;
to blend mixtures of powders, granules, and/or liquids
thoroughly; and
to help dissolve solid into liquid.
Parts of a blender
Parts and Functions of a Blender
Parts of a Blender
(Philips Domestic Appliances-Blender HR 1754)
Part Part
Part Name Part Name
No. No.
1 Panel 8 Motor
2 Drive Coupling 9 Bottom
3 Safety Switch 10 Stud
4 Housing 11 Safety Lid
5 3-Speed Switch 12 Jar Lid
6 Flex 13 Jar Assembly
7 Motor Cushion 14 Fruit/ Soybean Filter
14
Source: Philips Domestic Appliances and Personal Care/ Blender/ Service Manual
SELF CHECK 1.3
Blender
A. Identify the part of blender that is being described. Write your answer on
a separate sheet of paper.
Resources:
Domestic appliance: Electric Fan or Blender
(preferably electronically-controlled)
Maintain and repair form
Customer’s name:
Address:
Product/ Brand name:
Serial no:
Complain:
Condition/ Remarks:
Customer’s Signature:
Student technician signature:
Date:
SELF-CHECK CHECK 1.1
RECEIVING ELECTRONICALLY-CONTROLLED DOMESTIC
APPLIANCE FOR MAINTAIN/ REPAIR
V. PRE/DIAGNOSTIC ASSESSMENT
Troubleshooting Guide
A. Mechanical faults
B. Electrical faults
CHECKS TO BE SYSTEM
PROBLEM/SYMPTOMS
MADE DEFECTS/FAULTS
A. Check for an open
Defective stator
stator.
B. Check for an open
Defective wiring/AC cord
AC cord or wiring.
C. Check for an open
Defective fuse
AC line fuse.
D. Check for an open
1. Doesn’t rotate thermal cut-off (inside Defective thermal cut-off
the motor).
Defective
E. Check for an open
switch/electronic system
speed selector switch.
control
F. Check for a
Defective module(system
defective system
control)
control.
A. Check for a shorted
2. Starts to rotate only Defective capacitor
capacitor.
by manual turning of
B. Check for an open
the shaft Defective stator
start winding.
10
0
oscillation position
(clutch lever
Loose outer-wire set screw Tighten the screw.
system)
Worn worm wheel Replace the worn wheel.
Excessive thrust Adjust the thrust.
Bent yoke (frame) shaft Adjust the shaft.
Loosen rod set pin Tighten the pin.
Automatic oscillation Loosen rod set screw Tighten the screw.
system Excessive rod bore Replace the rod.
Worm gear shaft metal Replace the cover.
Unsteady Disengaged gear set screw Tighten the screw.
oscillation Adjust the thrust with the
Excessive gear thrust
washer.
Height adjustment of
standing fan
Unsteady or
Clogged of free stop bushing Adjust the bushing.
imperfect
vertical
movement
External appearance Scratch Touch up with a lacquer.
Scratch, stain or Wipe off with a cloth, soap
Dirt
breakage and water.
BLENDER
Using multimeter,
check continuity.
Using multimeter
Replace
Circuit breaker check Resistance as
Circuit breaker circuit
does not work below
failure. breaker
and motor a) black to red -20Ω
Motor burnt. Replace the
burns. b) black to blue- 22
motor
Ω
c. Black to Yellow-
24 Ω
Replace the
Circuit breaker Circuit breaker is Check continuity
circuit
does not restore open with multimeter
breaker.
Upper worn out
Replace upper
connector
Visual connector
Lower worn out
Replace lower
Blade is not connector
Visual connector
rotating. Foreign materials
Clean the
is between cutter
Visual cutter base
and base
assembly
assembly
SELF-CHECK 2.1
Procedure and Techniques in Troubleshooting an Electronically-
Controlled Domestic Appliance ECEF/ Blender
Resources:
Service manual of ECEF
Electric fan (functional and defective)
Activity sheet/ record sheet
Tools and Equipment Needed in Troubleshooting
Pliers
Mechanical pliers
Long nose pliers
Side-cutting pliers
Driving tools
Wrench (combination)
Set of Philip screw drivers
Set of standard (flat) screw drivers
Volt-Ohm Milliammeter
Cleaning materials
PPE
2. Make sure that you know how to operate an ECEF. If not, review the
operating manual as well as service manual (if available) of the unit
prior to its testing and operation
a. If you have worked on the same unit before, test out to see if it
operates in the same way.
b. Determine the last time it has been modified/repaired.
c. You must recognize the problem/ complain of the owner to the
unit.
4. For safety reason, check the AC plug of the unit with an ohmmeter
and record your findings. With this, you can formulate a diagnosis.
Customer’s name:
Address:
Product/ Brand name:
Serial no:
Complain:
Condition/ Remarks:
Customer’s Signature:
Student technician signature:
Date:
Teacher’s Initial:
Note: Copy the given format below on a sheet of paper and fill up with necessary
information.
SELF-CHECK 2.1
PRE-TESTING ELECTRONICALLY-CONTROLLED ELECTRIC FAN
Resources:
Service manual of Blender
Blender (functional and defective)
Activity sheet/ record sheet
Tools and Equipment Needed in Troubleshooting
Pliers
Mechanical pliers
Long nose pliers
Side-cutting pliers
Soldering tools
Screwdrivers
Set of Philip screw drivers
Set of standard (flat) screw drivers
Volt-Ohm Milliammeter
Cleaning materials
PPE
Before using any other accessory, make sure that the power unit is
turned off and placed in a suitable work surface. Put the protective cover
over the drive that you will not be using.
1. Before using the blender for the first time, wash the blender bowl;
cover funnel, blade assembly, and gasket in warm soapy water.
After washing, rinse well and dry them.
2. To assemble the blender, press the gasket into the recess in the
blade assembly base.
3. Then, insert the blade assembly into the blender bowl from
underneath. Using the lid as a wrench, tighten the blade
assembly into place. The blade assembly must be tightened firmly
to the bowl/jar to prevent leakage.
4. Turn the blender on the high-speed (upper) drive and turn to the
left (counter-clockwise) to lock the blender.
Customer’s name:
Address:
Product/ Brand name:
Serial no:
Complain:
Condition/ Remarks:
Customer’s Signature:
Student technician signature:
Date:
Teacher’s Initial:
Note: Copy the given format below on a sheet of paper and fill up with necessary
information.
SELF-CHECK 2.2
PRE-TESTING Blender