Professional Documents
Culture Documents
PARTS NOTICE
Reference
· WS11Q500 Inspection of M72 stud
bores in the big end bearing housing
· WS11V521 Visual examination protocol
for big end bearing housing M72 bore
corrosion
Section
111 Connecting rod
Introduction
In case the visual inspection of the M72
stud bores in big end bearing housing
(BEBH) indicates pitting corrosion as
mentioned in service bulletin WS11Q500,
the big end bearing housing should be
replaced.
A BEBH spare part kit (111 038) has been
created.
Validity
Until further notice. Replacing issue 1 dated
28 June 2019.
Before taking any action, always check the
available online systems for the latest
revision of this document. Any locally stored
or printed version is considered to be an
uncontrolled document.
Document history
Issue Date Description SBWT ID
1 28-06-2019 Initial release 003069
The feedback instructions have been updated, recording
2 13-02-2020 003333
of the inspection results to be done in record WS11V521.
Introduction
In case that corrosion is found within the criteria for component replacement as per
service bulletin WS11Q500, the big end bearing housing (BEBH) should be replaced.
A spare part kit (111 038) that contains the necessary spare parts for replacing the BEBH
has been created. The kit consists of the following parts:
· 111 004 Connecting rod lower part
· 111 018 Shim
· 111 037 Big end bearing kit
Figure 1, Big end bearing housing spare part kit (111 038)
Ordering
When ordering BEBH spare part kit 111 038, contact your nearest Wärtsilä
representative. During the ordering process, please specify the engine serial
number(s), part number (111 038), quantity needed and refer to service bulletin
WS11P503.
It is recommended that piston overhaul set (912 003) is also ordered for replacement
work.
Table 1, Ordering information
NOTE:
Wärtsilä also has a return process in place. In case that more BEBH kits (111 038) are
ordered, the return process guarantees that unopened kits can be returned to Wärtsilä.
Further instructions can be found on the next page.
© 2020 Wärtsilä Finland Oy – All rights reserved – Please read the complete disclaimer at the end of this document.
SPARE PARTS NOTICE
Return instructions for unopened big end bearing spare part kit(s)
Big end bearing housing spare part kit (111 038) are packed separately as a kit to enable
return process.
Normal ordering, transportation and possible goods return practices shall be conducted.
All transportations, customs and other costs shall be borne by the customer. The
customer has the right to return unopened big end bearing housing spare part kits without
re-stocking fee and get refunding for the ones returned that are in acceptable conditions.
Wärtsilä General Terms and Conditions - Parts 2019, or later applies.
ATTENTION:
In case that during the inspection of the M72 stud bore, pitting corrosion has been found,
housings need to be immediately scrapped to avoid any later usage. Related housings
can be marked e.g. with angle grinder. This also applies for M72 studs which can also
marked, e.g. by cutting the clear mark for threads.
Related documents
· WS11V521 – Visual examination protocol for big end bearing housing M72 bore
corrosion
· WS04Q397 – Connecting rod shim plate and ovality limits for big end bearing housing
· 4611P248 – Piston overhaul set for WÄRTSILÄ® 46 engines
· 5011P226 – Piston overhaul set for WÄRTSILÄ® 50DF and 50SG engines
Enclosures
Spare Parts Section: 111-0021A, BEB housing spare part kit, 1 page.
Contacts
For services, spare parts and/or tools, please contact your nearest Wärtsilä
representative.
111 038
111 018
111 037
111 004