Professional Documents
Culture Documents
Service Coduri Indesit Wgd934tx
Service Coduri Indesit Wgd934tx
WGD934TXR
Commercial code:
14497
18064
page 1
General notes
1. Models of same range share the same exploded views, which report the richest set of spare parts:generally, a model does not necessarly have a
related spare part for each particular shown on exploded views.
2. Some spare parts can not be represented directly on the exploded views (instruction booklets, specific kit, etc...). You can find those codes in the
spare parts list with the same reference of particular where spares are installed or with references 099, 999. Instruction booklets, once managed,
appear with 000 reference.
3. On the higher right site of each exploded view there is a serial number which indicates the beginning of the production of certain range:some
models might have more than an exploded view for a given category, each distinguished by a different serial no.and linked to another spare parts
list, In this case, serial no. is required to supply the right spare part code. Exploded view to be considered is the one with a more recent serial no.
but previous than the one of the model that needs assistance.
4.Exploded views might require further updates even after publishing. Addition of new spares will go on following the already existing numeration
references. Revision number of an exploded view is shown into last four digits of serial number into upper right hand corner.
5.The spare parts list associated to an exploded view shows related codes of spares managed for a certain model; for each spare part other
informations are available:
REF: reference no of spare into a table; SUBSTITUTE: list of spare(s) which can replace a code but that keeps same functional characteristics
INDUSTRIAL CODE: list of variables of a model (shown into model label) where such spare is used; NOTICE: code of information(s) to refer to
complete technical intervention, track for changes or to find correct spare part code.
6. Some notices, into a same section are generic therefore cannot be directly linked to a spare part. In order to assist a model in the best way as
possible, it is helpful to pay attention to all notices and constantly verify documentation updates
7.Technical documentation cover shows model name and its commercial codes
page 2
pdf_tavola_title_ENG
cod. 1120140
page 3
Spare parts list
page 4
020 C00021880 door glass
page 5
pdf_tavola_title_ENG
cod. 1120220
page 6
Spare parts list
page 7
017 C00045394 door bellows seal(detergent 0112101
recovery hose
page 8
043 C00037083 1 C00037177 heater bracket
page 9
pdf_tavola_title_ENG
cod. 1120320
page 10
Spare parts list
page 11
018 C00008372 1 C00022357 supply cable 3 x 1 nf
page 12
047 C00030357 pb/switch(ch/over 1 pole 0112101
e1533) nc+na
page 13
pdf_tavola_title_ENG
cod. 1120420
page 14
Spare parts list
page 15
001 C00032859 motor blower 230v. 50hz. 0112082,0112082,0112102,
0112082,0112102,0112102,
page 16
Notices
n1040013
New Indesit logo
-------------------------------------------------------------------------------------------------------------------------------
Beginning with serial no. 90301.0001, a new logo (as shown in the figure) will be printed or silk-screened on the control panels and the manuals for
the Indesit washing machines and washer-dryers.
The new parts will be handled with the same SAT numbers as the pre-modification parts (which will be eliminated).
n1040015
Top depth reduction
-------------------------------------------------------------------------------------------------------------------------------
Top depth was reduced in Super-Margherita and Giugiaro washing machines, with serial number 81012.0001 and 81022.0001, respectively.
The new tops are interchangeable with the pre-modification ones and the SAT codes 046139 (530 mm depth) for Super-Margherita and 044821
(530 mm depth) for Giugiaro remain unchanged (Historical consumption requirement).
Due to the presence of large stocks, the pre-modification tops 061931 Super-Margherita (540 mm depth) and 061932 (544 mm depth) Giugiaro
were re-coded.
n1040040
Tub cover
page 17
-------------------------------------------------------------------------------------------------------------------------------
Beginning from serial number 90614.0001 the washers and washer-dryers WGD1236TXR, WGD934TXR, WGD1030TXS, WGD1031TXEU,
WG1030TXD, WG1235TXEX and WG1435TXEX have been using a stainless steel tub cover instead of the enamelled one, as well as the tub
spring with code 049071.
Except for models WG1435TXEX and WG1235TXEX, due to management requirements, the documentation of these models already included the
stainless steel cover and the stainless steel tub cover seal in the spare part list instead of the enamelled ones.
IMPORTANT: always replace the seal when the tub cover is replaced.
n1040057
Front counterweight with two fixing points.
-------------------------------------------------------------------------------------------------------------------------------
Beginning with serial no. 91129.0001, a single 8 kg counterweight part no. 066404 was used on WGD834TR (18063), WGD836S (18259),
WGD835TX (18020) and WGD934TXR (18064) Washer-Dryers, instead of the two front counterweights part nos. 032865 and 032866.
During production, to apply the new counterweight, a new tub cover was used with two brackets rather than four.
For Technical Assistance, the pre-modification cover (with four brackets) will continue to be handled because to fix the new counterweight, the two
brackets are used and positioned on the lower part of the cover (the opposite area to the positioning tab).
page 18
032870 - Enamelled tub cover with 4 brackets;
038672 - M8 X 55 screw(X2);
038672 - 8 X 55 screw(X2);
In the future the modification will be extended to other models which will be related to this notice.
n1040060
Remco modules with 12 A Triac
-------------------------------------------------------------------------------------------------------------------------------
Beginning with serial no. 00217.0001, the following modules with 12 A triac have been used on appliances produced at the Comunanza / Teverola
factory:
The new modules can be used instead of the corresponding pre-modification modules, which will continue to be handled normally until stocks run
out.
page 19
0112082
HERMETICALLY SEALED BLOWER UNIT
-------------------------------------------------------------------------------------------------------------------------------
Beginning with serial number 70224.0001 for washer-dryers and WGD834TR, WGD1035TR, WGD1236TXR, WGD1230TXEU, the following
components have been used to hermetically seal the blower unit to prevent the leakage of soap suds due to excessive formation of suds.
On the top part of the blower unit, the breather hole was closed on the inside of the small cylinder extending from the top surface.
The new component is interchangeable with the pre-modification part by re-opening the breather hole with a 6 mm drill bit (in order to avoid
pressure build-up), it has the same SAT code 032854.
0112101
VARIOUS CHANGES
-------------------------------------------------------------------------------------------------------------------------------
Beginning with serial no. 71208.0001, production needs have dictated that several parts be changed on the following washer-dryers: WD834TR,
WGD1035TR, WGD1236TXR and WGD934TXR.
They include the timer, electoronic module the motor, the drum, the detergent recovery hose, the door seal, the drain pump, electrovalve and
others.
In light of the vast number of parts affected by this modification, it became necessary to omit the list of the new part numbers used on the various
models. They can be tracked down through the notice number, linked to the new spare parts and present in the catalogue.
0112102
MODIFIED BLOWER BODIES AND FAN MOTOR
-------------------------------------------------------------------------------------------------------------------------------
Beginning with serial no. 71222.0001, the top and bottom blower casings are now being made of aluminium, instead of zamak, and are used on all
washer-dryers . In addition, a new fan motor is being used secured with four fastening screws.
The assembly of the two new blower bodies (part no. 054789) is done using seven torx screws (part no. 054790) instead of the clamps (part no.
032856).
Therefore, the individual parts are not interchangeable with the pre-modification ones.
page 20
However, the blowers are interchangeable if they are already assembled and the new fan motor is used.
Until all of the stock has been used, the kit will include the blower units made of zamak, secured with fastening clips.
The new fan motor (part no. 056344) fastened now with four screws (part no. 056028) can be used in place of the pre-modification motor, but not
vice versa.
The motor (part no. 052947) will be handled as a spare part until all of the stock is used up.
0112129
-------------------------------------------------------------------------------------------------------------------------------
Beginning with serial no. 80713.0001 on all of the 800 rpm washing machines and washer-dryers produced at the factory in Comunanza, the inner
drum with part no. 042979 is being used.
Unless used as a complete assembly, the new parts are not individually interchangeable with the pre-modification ones, which will continue to be
handled normally.
0112130
-------------------------------------------------------------------------------------------------------------------------------
Beginning with serial no. 80825.0001 on the Giugiaro washing machines and washer dryers, (WG and WDG), the rear cover, outlet hose, terminal
block and cushion frame cabinet have been changed.
The modified cabinet keeps the same SAT code as the pre-modification ones(045221), and in order to maintain the same interchangeability, it is
handled assembled with rear panel and terminal block.
page 21
0112136
-------------------------------------------------------------------------------------------------------------------------------
Beginning with serial no. 81020.0001, some of the washing machine and washer-dryer models in the WG, WGS and WGD lines produced at the
factories in Teverola and Comunanza will utilize a door with a central handle (on axis with the hinge).
page 22
0112142
-------------------------------------------------------------------------------------------------------------------------------
Beginning with serial no. 81116.0001, some of the washing machines and washer-dryers will have a tub balancing system that utilizes dampers
instead of leaf springs and linings.
Part no. 033092 - Stainless steel tub with attachment for dampers;
Part no. 056795 - Enameled tub with detergent recovery hose and dampers;
page 23
Part no. 038358 - Metric Screw: M8x16 (WITH LOCTITE);
Beginning with the same serial number on the WA1451X washing machine, the tub with part no. 043434 and the front counterweight with part no.
059213 will be used. Four washers with part no. 039670 must be used to fasten them, instead of the ones with part no. 037346.
If used as an assembly, the new parts are interchangeable with the pre-modification ones, which will continue to be handled normally.
n1040013
New Indesit logo
-------------------------------------------------------------------------------------------------------------------------------
Beginning with serial no. 90301.0001, a new logo (as shown in the figure) will be printed or silk-screened on the control panels and the manuals for
the Indesit washing machines and washer-dryers.
The new parts will be handled with the same SAT numbers as the pre-modification parts (which will be eliminated).
n1040015
Top depth reduction
-------------------------------------------------------------------------------------------------------------------------------
Top depth was reduced in Super-Margherita and Giugiaro washing machines, with serial number 81012.0001 and 81022.0001, respectively.
The new tops are interchangeable with the pre-modification ones and the SAT codes 046139 (530 mm depth) for Super-Margherita and 044821
(530 mm depth) for Giugiaro remain unchanged (Historical consumption requirement).
page 24
Due to the presence of large stocks, the pre-modification tops 061931 Super-Margherita (540 mm depth) and 061932 (544 mm depth) Giugiaro
were re-coded.
n1040040
Tub cover
-------------------------------------------------------------------------------------------------------------------------------
Beginning from serial number 90614.0001 the washers and washer-dryers WGD1236TXR, WGD934TXR, WGD1030TXS, WGD1031TXEU,
WG1030TXD, WG1235TXEX and WG1435TXEX have been using a stainless steel tub cover instead of the enamelled one, as well as the tub
spring with code 049071.
Except for models WG1435TXEX and WG1235TXEX, due to management requirements, the documentation of these models already included the
stainless steel cover and the stainless steel tub cover seal in the spare part list instead of the enamelled ones.
IMPORTANT: always replace the seal when the tub cover is replaced.
n1040057
Front counterweight with two fixing points.
-------------------------------------------------------------------------------------------------------------------------------
Beginning with serial no. 91129.0001, a single 8 kg counterweight part no. 066404 was used on WGD834TR (18063), WGD836S (18259),
WGD835TX (18020) and WGD934TXR (18064) Washer-Dryers, instead of the two front counterweights part nos. 032865 and 032866.
During production, to apply the new counterweight, a new tub cover was used with two brackets rather than four.
page 25
For Technical Assistance, the pre-modification cover (with four brackets) will continue to be handled because to fix the new counterweight, the two
brackets are used and positioned on the lower part of the cover (the opposite area to the positioning tab).
038672 - M8 X 55 screw(X2);
038672 - 8 X 55 screw(X2);
In the future the modification will be extended to other models which will be related to this notice.
n1040060
Remco modules with 12 A Triac
-------------------------------------------------------------------------------------------------------------------------------
Beginning with serial no. 00217.0001, the following modules with 12 A triac have been used on appliances produced at the Comunanza / Teverola
factory:
page 26
The new modules can be used instead of the corresponding pre-modification modules, which will continue to be handled normally until stocks run
out.
0112082
HERMETICALLY SEALED BLOWER UNIT
-------------------------------------------------------------------------------------------------------------------------------
Beginning with serial number 70224.0001 for washer-dryers and WGD834TR, WGD1035TR, WGD1236TXR, WGD1230TXEU, the following
components have been used to hermetically seal the blower unit to prevent the leakage of soap suds due to excessive formation of suds.
On the top part of the blower unit, the breather hole was closed on the inside of the small cylinder extending from the top surface.
The new component is interchangeable with the pre-modification part by re-opening the breather hole with a 6 mm drill bit (in order to avoid
pressure build-up), it has the same SAT code 032854.
0112101
VARIOUS CHANGES
-------------------------------------------------------------------------------------------------------------------------------
Beginning with serial no. 71208.0001, production needs have dictated that several parts be changed on the following washer-dryers: WD834TR,
WGD1035TR, WGD1236TXR and WGD934TXR.
They include the timer, electoronic module the motor, the drum, the detergent recovery hose, the door seal, the drain pump, electrovalve and
others.
In light of the vast number of parts affected by this modification, it became necessary to omit the list of the new part numbers used on the various
models. They can be tracked down through the notice number, linked to the new spare parts and present in the catalogue.
page 27
0112102
MODIFIED BLOWER BODIES AND FAN MOTOR
-------------------------------------------------------------------------------------------------------------------------------
Beginning with serial no. 71222.0001, the top and bottom blower casings are now being made of aluminium, instead of zamak, and are used on all
washer-dryers . In addition, a new fan motor is being used secured with four fastening screws.
The assembly of the two new blower bodies (part no. 054789) is done using seven torx screws (part no. 054790) instead of the clamps (part no.
032856).
Therefore, the individual parts are not interchangeable with the pre-modification ones.
However, the blowers are interchangeable if they are already assembled and the new fan motor is used.
Until all of the stock has been used, the kit will include the blower units made of zamak, secured with fastening clips.
The new fan motor (part no. 056344) fastened now with four screws (part no. 056028) can be used in place of the pre-modification motor, but not
vice versa.
The motor (part no. 052947) will be handled as a spare part until all of the stock is used up.
0112129
-------------------------------------------------------------------------------------------------------------------------------
Beginning with serial no. 80713.0001 on all of the 800 rpm washing machines and washer-dryers produced at the factory in Comunanza, the inner
drum with part no. 042979 is being used.
Unless used as a complete assembly, the new parts are not individually interchangeable with the pre-modification ones, which will continue to be
handled normally.
0112130
-------------------------------------------------------------------------------------------------------------------------------
Beginning with serial no. 80825.0001 on the Giugiaro washing machines and washer dryers, (WG and WDG), the rear cover, outlet hose, terminal
block and cushion frame cabinet have been changed.
page 28
The items subjected to new modifications are:-
The modified cabinet keeps the same SAT code as the pre-modification ones(045221), and in order to maintain the same interchangeability, it is
handled assembled with rear panel and terminal block.
0112136
-------------------------------------------------------------------------------------------------------------------------------
Beginning with serial no. 81020.0001, some of the washing machine and washer-dryer models in the WG, WGS and WGD lines produced at the
factories in Teverola and Comunanza will utilize a door with a central handle (on axis with the hinge).
page 29
Serial No.81120.00001 Mod. WG421TXR; Commercial Code from 14488 to 18058;
0112142
-------------------------------------------------------------------------------------------------------------------------------
Beginning with serial no. 81116.0001, some of the washing machines and washer-dryers will have a tub balancing system that utilizes dampers
instead of leaf springs and linings.
Part no. 033092 - Stainless steel tub with attachment for dampers;
page 30
Part no. 038358 - Bottom Damper Screw: TEFS M8 X 16 dry-loc
Part no. 056795 - Enameled tub with detergent recovery hose and dampers;
Beginning with the same serial number on the WA1451X washing machine, the tub with part no. 043434 and the front counterweight with part no.
059213 will be used. Four washers with part no. 039670 must be used to fasten them, instead of the ones with part no. 037346.
If used as an assembly, the new parts are interchangeable with the pre-modification ones, which will continue to be handled normally.
page 31
Electric schemes and links
Cod. 112201a
page 32
Legend
Legend: 112201a
EF/P Electro-Valve Cold Water / Prewash P1 1st level pressure cut-off switch
page 33
IC Switch N.C. - 1/2 Load TB Low Temperature Thermostat
BF Terminal board contact, motor fan and dryer NC Spin cycle exclusion
heatin
page 34
EVL Wash electrovalve RV Speed regulator
page 35
Electric schemes and links
Cod. 112227b
page 36
Legend
Legend: 112227b
BF Terminal board contact, motor fan and dryer NC Spin cycle exclusion
heatin
page 37
IE Water Saving Device TC Spider wheel earth
page 38
Electric schemes and links
Cod. 112227c
page 39
Legend
Legend: 112227c
BF Terminal board contact, motor fan and dryer NC Spin cycle exclusion
heatin
page 40
IE Water Saving Device TC Spider wheel earth
page 41
Electric schemes and links
Cod. 112305a
page 42
Legend
Legend: 112305a
BF Terminal board contact, motor fan and dryer NC Spin cycle exclusion
heatin
page 43
IE Water Saving Device TC Spider wheel earth
page 44
Electric schemes and links
Cod. 112305b
page 45
Legend
Legend: 112305b
BF Terminal board contact, motor fan and dryer NC Spin cycle exclusion
heatin
page 46
IE Water Saving Device TC Spider wheel earth
page 47
Electric schemes and links
Cod. 112305c
page 48
Legend
Legend: 112305c
BF Terminal board contact, motor fan and dryer NC Spin cycle exclusion
heatin
page 49
IE Water Saving Device TC Spider wheel earth
page 50