Professional Documents
Culture Documents
1:CP
Features
D Compact/Light Weight— The Design CP control
valve is designed specifically for Class 150 and 300
service.
2
Bulletin 51.1:CP
Table 1. Maximum Allowable Inlet Pressures for M35-1, CW2M, N7M, and CN7M Valves
CW2M(1) (HASTELLOY C) AND
M35-1(1) (MONEL) CN7M (ALLOY 20)(3)
TEMPERATURE N7M(1) (HASTELLOY B)
150(2) 300(2) 150(2) 300(2) 150(2) 300(2)
_C Bar
–46 to 38 15.9 41.4 20.0 51.7 15.9 41.4
93 13.8 36.5 17.9 51.7 14.8 38.3
149 13.1 34.1 15.9 50.3 13.8 36.2
204 12.8 33.1 13.8 48.6 12.8 33.1
260 11.7 32.8 11.7 45.9 11.7 32.4
316 9.7 32.8 9.6 41.7 9.7 31.4
371 7.6 32.8 7.6 39.3 7.6 30.7
427 5.5 31.7 5.5 35.2 5.5 29.6
_F Psig
–50 to 100 230 600 290 750 230 600
200 200 530 260 750 215 555
300 190 495 230 730 200 525
400 185 480 200 705 185 480
500 170 475 170 665 170 470
600 140 475 140 605 140 455
700 110 475 110 570 110 445
800 80 460 80 510 80 430
1. These materials are not listed in ASME B16.34.
2. The designations 150 and 300 are used only to indicate relative pressure-retaining capabilities and are not ANSI pressure-temperature rating class designations.
3. Alloy 20 is rated in ASME B16.34 to 149_C (300_F). Fisher extends the rating to 427_C (800_F).
3
Bulletin 51.1:CP
Table 4. Valve Pressure Drops—all except Whisper Trim and Cavitrol III trims (Metal Seat)
METAL SEAT
Shutoff Pressure Drop Flowing Pressure Drop
VALVE PORT
Flow Up Flow Down
SIZE,
SIZE DIAMETER
Trim Trim Trim
INCHES
1, 5, 7, 8, 9 3, 6 1, 5, 7, 8, 9 3, 6 1, 3, 5, 6, 7, 8, 9
mm Bar Bar
4.8
Micro-Flow 20.7 51.7 --- --- 51.7(1)
1/2x1, Plugs
3/4x1, 4.8
and 1
6.4 20.7 51.7 --- --- 51.7(1)
9.5
12.7 20.7 51.7 --- --- 51.7(1)
1&1
1-1/2
1/2
19.1 20.7 51.7 20.7 51.7 51.7
1-1/2 28.6 20.7 51.7 20.7 51.7 51.7
19.1 20.7 51.7 20.7 51.7 51.7
2 28.6 20.7 51.7 20.7 51.7 51.7
38.1 20.7 51.7 20.7 51.7 34.5
28.6 20.7 51.7 20.7 51.7 34.5
3 47.6 20.7 51.7 20.7 51.7 34.5
63.5 20.7 51.7 20.7 51.7 27.6
38.1 20.7 51.7 20.7 51.7 27.6
4 63.5 20.7 51.7 20.7 51.7 27.6
82.6 20.7 51.7 20.7 51.7 17.2
Inches Psi Psi
3/16
Micro-Flow 300 750 --- --- 750(1)
1/2x1, Plugs
3/4x1, 3/16
and 1
1/4 300 750 --- --- 750(1)
3/8
1/2 300 750 --- --- 750(1)
1&1
1-1/2
1/2
3/4 300 750 300 750 750
1-1/2 1-1/8 300 750 300 750 750
3/4 300 750 300 750 750
2 1-1/8 300 750 300 750 750
1-1/2 300 750 300 750 500
1-1/8 300 750 300 750 500
3 1-7/8 300 750 300 750 500
2-1/2 300 750 300 750 400
1-1/2 300 750 300 750 400
4 2-1/2 300 750 300 750 400
3-1/4 300 750 300 750 250
1. Flow up direction recommended for port sizes equal to or less than valve stem guide diameter.
4
Bulletin 51.1:CP
Table 5. Valve Pressure Drops—Whisper Trim (Composition Seat)
COMPOSITION SEAT
Shutoff Pressure Drop
VALVE PORT Flowing Press re Drop
Pressure
Flow Up Flow Down
SIZE,
SIZE DIAMETER
Trim Trim Trim
INCHES
11, 16 15 17, 19 11, 16 15 17, 19 11, 15, 16, 17, 19
mm Bar Bar Bar
1-1/2 28.6 51.7 51.7 51.7 51.7 51.7 51.7 51.7
2 38.1 51.7 51.7 51.7 51.7 51.7 51.7 34.5
3 63.5 51.7 44.1 51.7 51.7 44.1 51.7 27.6
4 82.6 51.7 25.2 35.5 51.7 25.2 35.5 17.2
Inches Psi Psi Psi
1-1/2 1-1/8 750 750 750 750 750 750 750
2 1-1/2 750 750 750 750 750 750 500
3 2-1/2 750 640 750 750 640 750 400
4 3-1/4 750 365 515 750 365 515 250
Table 6. Valve Pressure Drops—all except Whisper Trim and Cavitrol III trims (Composition Seat)
COMPOSITION SEAT
Shutoff Pressure Drop
VALVE PORT Flowing Press re Drop
Pressure
Flow Up Flow Down
SIZE,
SIZE DIAMETER
Trim Trim Trim
INCHES
1, 6 8 5 7, 9 1, 6 8 5 7, 9 1, 5, 6, 7, 8, 9
mm Bar Bar Bar
1/2x1,
3/4x1, 12.7 51.7 51.7 51.7 51.7 51.7 51.7 51.7 51.7 51.7(1)
and 1
3/4x1,
19.1 51.7 51.7 51.7 51.7 51.7 51.7 51.7 51.7 51.7
and 1
19.1 51.7 51.7 51.7 51.7 51.7 51.7 51.7 51.7 51.7
1 1/2
1-1/2
28.6 51.7 51.7 51.7 51.7 51.7 51.7 51.7 51.7 51.7
28.6 51.7 51.7 51.7 51.7 51.7 51.7 51.7 51.7 51.7
2
38.1 51.7 51.7 51.7 51.7 51.7 51.7 51.7 51.7 34.5
47.6 51.7 51.7 51.7 51.7 51.7 51.7 51.7 51.7 34.5
3
63.5 51.7 27.6 44.1 51.7 51.7 27.6 44.1 51.7 27.6
63.5 51.7 27.6 44.1 51.7 51.7 27.6 44.1 51.7 27.6
4
82.6 51.7 15.9 25.2 35.5 51.7 15.9 25.2 35.5 17.2
Inches Psi Psi Psi
1/2x1,
3/4x1, 1/2 750 750 750 750 750 750 750 750 750(1)
and 1
3/4x1,
3/4 750 750 750 750 750 750 750 750 750
and 1
3/4 750 750 750 750 750 750 750 750 750
1 1/2
1-1/2
1-1/8 750 750 750 750 750 750 750 750 750
1-1/8 750 750 750 750 750 750 750 750 750
2
1-1/2 750 750 750 750 750 750 750 750 500
1-7/8 750 750 750 750 750 750 750 750 500
3
2-1/2 750 400 640 750 750 400 640 750 400
2-1/2 750 400 640 750 750 400 640 750 400
4
3-1/4 750 230 365 515 750 230 365 515 250
1. Flow up direction recommended for port sizes equal to or less than valve stem guide.
5
Bulletin 51.1:CP
Table 7. Composition Seat Materials
Part Material
Disk Retainer S31603 (316L SST), N10276 (Hastelloy C276),
N10665 (Hastelloy B), N08020 (Alloy 20),
N05500 (K-Monel), or S30403 (304L SST)
Disk PTFE/Carbon Graphite
Disk Seat S31603 (316L SST), N10276 (Hastelloy C276),
N10665 (Hastelloy B), N08020 (Alloy 20), N05500
(K-Monel), or S30403 (304L SST)
Table 8. Typical Combinations of Metal Trim Parts—All Except Whisper Trim and Cavitrol III Trims
Trim Designation Seat Ring Seat Ring Retainer Valve Plug/Stem Assy
1 (standard for WCC and
S31603 (316L stainless steel) CF3M (316L stainless steel) S31603(1)(2) (316L stainless steel)
CF3M valve bodies)
3 R30006 (Alloy 6) CF3M S31603(1)(2) / CoCr-A(3) seat
5 N08020 (Alloy 20) CN7M (Alloy 20) N08020
6 N05500 (K-Monel) M35-1 (Monel) N05500
7 N10276 (Hastelloy C276) CW2M (Hastelloy C) N06022 (Hastelloy C22)
8 S30403 (304L stainless steel) CF3 (304L stainless steel) S30403
9 N10665 (Hastelloy B2) N7M (Hastelloy B2) N10665
1. Material is strain-hardened S31603.
2. Micro-Flow plug tip is R30006.
3. Certain trim combinations use solid R30006 (Alloy 6).
6
Bulletin 51.1:CP
Table 11. Temperature Capabilities of Valve Body-Trim Combinations
VALVE TRIM TEMPERATURE CAPABILITIES
BODY DESIGNATION
MATERIAL PER TABLES 8, 9, AND 10 _C _F
1, 3, 5, 6, 7, 8, 9, 11, 13, 15, 16,
WCC steel –29 to 427 –20 to 800
17, 19, 20, 23, 24
1, 3, 5, 6, 7, 8, 9, 11, 13, 15, 16,
LCC steel –46 to 371 –50 to 700
17, 19, 20, 23, 24
1, 3, 5, 6, 7, 8, 9, 11, 13, 15, 16,
–198 to 427 –325 to 800
CF3M (316L stainless steel) 17, 19, 23, 24
20 –79 to 427 –110 to 800
CN7M (Alloy 20) 5, 15 –198 to 427(1) –325 to 800(1)
M35-1 (Monel) 6, 16, 24 –198 to 427(1) –325 to 800(1)
CW2M (Hastelloy C) 7, 17 –198 to 427(1) –325 to 800(1)
CF3 (304L stainless steel) 8(1), –198 to 427 –325 to 800
N7M (Hastelloy B) 9, 19 –198 to 427(1) –325 to 800(1)
1. For applications above 232_C (450_F), compatibility of graphite body/bonnet gasket must be verified.
W6377-1 / IL
Figure 2. Design CP Control Valve with Equal-Percentage Valve Plug and Optional ENVIRO-SEAL PTFE Packing (Size 2 shown)
7
Bulletin 51.1:CP
FLUID TEMPERATURE, _C
1
0 100 200
600 40
30
400
20
200
10
60
0 0
–200 –100 0 100 200 300 400 500
–40 80 450
FLUID TEMPERATURE, _F
NOTE;
1 SEE TABLES 5 AND 6 FOR FLOWING PRESSURE
DROPS AND ADDITIONAL SHUTOFF PRESSURE DROP
A6661/IL LIMITATIONS
24B9310
A6744/IL
44B7825-A / IL 44B7825-A / IL
8
Bulletin 51.1:CP
Table 12. Materials and Temperature Limits (1/2 and 3/4-Inch Valves)
TEMPERATURE CAPABILITIES
PART MATERIAL
_C _F
Valve body & bonnet w/ integral valve body seat CF3M (316L SST)
Valve plug/stem 316L
316L/Alloy 6 (optional)
Packing box spacer 316L
Gaskets Bonnet Graphite Laminated S31600 (316 SST) –40
40 to 232 (Limited to this –40
40 to 450 (Limited to this
Body-to- CF3M Studs Stainless steel (SA-193-B8M) temperature range by temperature range by
bonnet valve body PTFE packing) PTFE packing)
bolting Nuts Stainless steel (SA-194-8M)
Packing nut Nitronic 60
Packing (temperatures shown are Live- ENVIRO-SEAL Double PTFE V-Ring
material temperature capabilities). load for 500 ppm service
B2528/IL
W6434-1 / IL
9
Bulletin 51.1:CP
Table 13. Materials and Temperature Limits (1/2x1- through 4-Inch Valves)
TEMPERATURE CAPABILITIES
PART MATERIAL
_C _F
Valve body & bonnet WCC steel, LCC steel, CF3M (316L See table 11 for See table 11 for
SST), CN7M (Alloy 20), M35-1 temperature capabilities temperature capabilities
(Monel), CW2M (Hastelloy C), CF3 of body-trim of body-trim
(304L SST), N7M (Hastelloy B) combinations combinations
Valve plug & stem See table 8 See table 11 See table 11
and seat ring retainer
Seat ring Metal (see table 8) See table 11 See table 11
Optional Trim
Composition Designation
Seat Disk 1(1), 5, 6, 7, 8(1), 9 Carbon-filled PTFE –29 to 232 –20 to 450
Gaskets Seat ringg Glass-filled PTFE –40 to 232 –40 to 450
Carbon-filled PTFE –40 to 232 –40 to 450
N06600 (Inconel 600)/Graphite –254 to 593 –425 to 1100
Calcium Fluoride Filled PTFE(2) –40 to 232 –40 to 450
Bonnet Graphite Laminated S31600 (316 SST) –254 to 593 –425 to 1100
PTFE-coated alloy –40 to 232 –40 to 450
Body-to-
y WCC valve Studs Steel (SA-193-B7-ENC)(3) (standard) –46
46 to 427((4)) 50 to 800((4))
–50
b
bonnet t b di
bodies Nuts Steel (SA-194-2H-ENC) (standard)
bolting
Studs Steel (SA-193-B7M-ENC)(3) 46 to 427((4))
–46 50 to 800((4))
–50
Nuts Steel (SA-194-2HM ENC)
LCC valve Studs Steel (SA-193-B7-ENC)(3) (standard) 46 to 371((4))
–46 50 to 700((4))
–50
b di
bodies Nuts Steel (SA-194-2H-ENC) (standard)
Studs Steel (SA-193-B7M-ENC)(3) 46 to 371((4))
–46 50 to 700((4))
–50
Nuts Steel (SA-194-2HM-ENC)
CF3M Studs Steel (SA-193-B7-ENC)(3) (standard) 46 to 427((4))
–46 50 to 800((4))
–50
l bodies
valve b di Nuts Steel (SA-194-2H-ENC) (standard)
Studs Stainless steel (SA-193-B8M) 198 to 649((4))
–198 325 to 1200((4))
–325
Nuts Stainless steel (SA-194-8M)
Studs Steel (SA-193-B7M-ENC)(3) 46 to 427((4))
–46 50 to 800((4))
–50
Nuts Steel (SA-194-2HM-ENC)
CF3 Studs Steel (SA-193-B7-ENC)(3) (standard) 46 to 427((4))
–46 50 to 800((4))
–50
l bodies
valve b di Nuts Steel (SA-194-2H-ENC) (standard)
Studs Stainless steel (SA-193-B8M) 198 to 427((4))
–198 325 to 800((4))
–325
Nuts Stainless steel (SA-194-8M)
Studs Steel (SA-193-B7M-ENC)(3) 46 to 427((4))
–46 50 to 800((4))
–50
Nuts Steel (SA-194-2HM-ENC)
CN7M Studs Steel (SA-193-B7-ENC)(3) (standard) 46 to 427((4))
–46 –50 to 800(4)
l bodies
valve b di Nuts Steel (SA-194-2H-ENC) (standard)
Studs Stainless steel (SA-193-B8M) 198 to 427((4))
–198 –325 to 800(4)
Nuts Stainless steel (SA-194-8M)
Studs Steel (SA-193-B7M-ENC)(3) 46 to 427((4))
–46 –50 to 800(4)
Nuts Steel (SA-194-2HM-ENC)
1. Trims 1 and 8 are limited to 149_C (300_F) in non-lubricated service.
2. This material is for hydrofluoric acid (HF) applications.
3. Electroless Nickel Coating.
4. Use lubricated nuts for temperatures above 232_C (450_F).
- Continued -
10
Bulletin 51.1:CP
Table 13. Materials and Temperature Limits (1/2x1- through 4-Inch Valves) (Continued)
TEMPERATURE CAPABILITIES
PART MATERIAL
_C _F
Body-to-
y CW2M Studs Steel (SA-193-B7-ENC)(3) (standard) –46
46 to 427((4)) –50
50 to 800((4))
b
bonnet t valve
l bodies
b di Nuts Steel (SA-194-2H-ENC) (standard)
bolting
Studs Stainless steel (SA-193-B8M) 198 to 427((4))
–198 325 to 800((4))
–325
Nuts Stainless steel (SA-194-8M)
Studs Steel (SA-193-B7M-ENC)(3) 46 to 427((4))
–46 50 to 800((4))
–50
Nuts Steel (SA-194-2HM-ENC)
M35-1 valve bodies Studs Steel (SA-193-B7-ENC)(3) (standard) 46 to 427((4))
-46 50 to 800((4))
-50
Nuts Steel (SA-194-2H-ENC) (standard)
Studs Stainless steel (SA-193-B8M) –198 to 427 –325 to 800
Nuts Stainless steel (SA-194-8M)
Studs Steel (SA-193-B7M-ENC)(3) 46 to 427((4))
–46 50 to 800((4))
–50
Nuts Steel (SA-193-2HM-ENC)
N7M valve bodies Studs Steel (SA-193-B7-ENC)(3) (standard) 46 to 427((4))
-46 50 to 800((4))
-50
Nuts Steel (SA-194-2H-ENC) (standard)
Studs Stainless steel (SA-193-B8M) 198 to 427((4))
–198 325 to 800((4))
–325
Nuts Stainless steel (SA-194-8M)
Studs Steel (SA-193-B7M-ENC)(3) 46 to 427((4))
–46 50 to 800((4))
–50
Nuts Steel (SA-193-2HM-ENC)
Packing
g flange
g studs Studs Stainless steel (SA-193-B8M) –198 to 454 –325 to 850
d nuts
and t Nuts Stainless steel (SA-194-8M)
Studs Steel (SA-193-B7M-ENC)(3) –46 to 427 –50 to 800
Nuts Steel (SA-194-2HM-ENC)
Studs N08020 (Alloy 20) –198 to 427 –325 to 800
Nuts N08020
Studs N04400 (Monel 400) –198 to 427 –325 to 800
Nuts N04400
Studs N10276 (Hastelloy C276) –198 to 538 –325 to 1000
Nuts N10276
Studs Stainless steel (SA-193-B8) –198 to 427 –325 to 800
Nuts Stainless steel (SA-194-8)
Studs N10665 (Hastelloy B2) –198 to 427 –325 to 800
Nuts N10665
Packing
g flange
g S31600 –198 to 427 –325 to 800
N08020 –198 to 427 –325 to 800
N04400 –198 to 427 –325 to 800
N10276 –198 to 427 –325 to 800
S30400 (304 stainless steel) –198 to 427 –325 to 800
N10665 –198 to 427 –325 to 800
1. Trims 1 and 8 are limited to 149_C (300_F) in non-lubricated service.
2. This material is for hydrofluoric acid (HF) applications.
3. Electroless Nickel Coating.
4. Use lubricated nuts for temperatures above 232_C (450_F).
- Continued -
11
Bulletin 51.1:CP
Table 13. Materials and Temperature Limits (1/2x1- through 4-Inch Valves) (Continued)
TEMPERATURE CAPABILITIES
PART MATERIAL
_C _F
Packing
g ((temperatures shown are Std Double PTFE V-Ring –46 to 232 –50 to 450
material
t i l ttemperature
t capabilities).
biliti ) Single graphite ribbon/filament –198 to 371 –325 to 700
Live- ENVIRO-SEAL Double PTFE V-Ring –46 to 232 –50 to 450
load for 500 ppm service
ENVIRO-SEAL Single Graphite for –7 to 315 20 to 600
500 ppm service
ENVIRO-SEAL Single Graphite for –198 to 371 –325 to 700
nonenvironmental service
ENVIRO-SEAL Duplex—PTFE –46 to 232 –50 to 450
V-Ring and Graphite
Lower Bushing
g (Packing
( g Box)) S31600/PTFE –198 to 232 –325 to 450
N08020 - PTFE/Glass –73 to 232 –100 to 450
N04400 - PTFE/Glass
N10276 - PTFE/Glass
S30403 - PTFE/Glass
N10665 - PTFE/Glass
N08020 - PTFE/Carbon –73 to 232 –100 to 450
N04400 - PTFE/Carbon
N10276 - PTFE/Carbon
S30403 - PTFE/Carbon
N10665 - PTFE/Carbon
Carbon –198 to 427 –325 to 800
1. Trims 1 and 8 are limited to 149_C (300_F) in non-lubricated service.
2. This material is for hydrofluoric acid (HF) applications.
3. Electroless Nickel Coating.
4. Use lubricated nuts for temperatures above 232_C (450_F).
Table 14. Port Diameters, Travel, and Stem Diameters (1/2x1- through 4-Inch Valves)
VALVE PORT VALVE VALVE STEM
SIZE, DIAMETER TRAVEL GUIDE DIAMETER(1)
INCHES mm Inches mm Inches mm Inches
4.8 3/16
1/2x1, 6.4 1/4
3/4x1
3/4x1,
9.5 3/8
and 1
12.7 1/2
3/4x1, 19 3/4 12.7 1/2
19.1 3/4
and 1
12.7 1/2
1-1/2
1 1/2 19.1 3/4
28.6 1-1/8
19.1 3/4
19 3/4
28.6 1-1/8
2 15 9
15.9 5/8
19 3/4
38 1
38.1 1 1/2
1-1/2
29(2) 1-1/8(2)
28.6 1-1/8 19 3/4
3 47.6 1-7/8 25.4 1
29 1 1/2
1-1/2
63.5 2-1/2
38.1 1-1/2 29 1-1/8
4 63.5 2-1/2 38 1-1/2 31.8 1-1/4
1 1/4
82.6 3-1/4 51 2
1. Stem diameter at actuator stem connector is 9.5 mm (3/8 inch) on 1, 1-1/2, and 2 inch valves and is 12.7 mm (1/2 inch) on 3 and 4 inch valves.
2. Valve travel is 29 mm (1-1/8 inches) when a 2-inch valve with 38.1 mm (1-1/2 inch) port diameter has either Whisper Trim or Cavitrol III trim.
12
Bulletin 51.1:CP
A B
VALVE STEM
Long(1) Long(1) D G
SIZE, Standard Standard Standard Standard CONNECTOR
Class 150 Class 150
INCHES Class 150 Class 300 Class 150 Class 300 DIAMETER
and 300 and 300
mm
1/2 184 190 216 92 95 108 69 32 7.9
3/4 184 194 216 92 97 108 69 32 7.9
1/2x1 --- --- 216 --- --- 108 69 47.8 9.7
3/4x1 --- --- 216 --- --- 108 69 47.8 9.7
1 184.2 196.9 215.9 91.9 98.6 108.0 91.9 47.8 9.7
1-1/2 222.3 235.0 241.3 111.3 117.3 120.7 108.0 57.2 9.7
2 254.0 266.7 292.1 127.0 133.4 146.1 122.2 69.9 9.7
3 298.4 317.5 355.6 149.4 158.7 177.8 162.1 93.7 12.7
4 352.6 368.3 431.8 176.3 184.1 215.9 195.3 112.8 12.7
Inches
1/2 7.25 7.50 8.50 3.63 3.75 4.25 2.69 1.25 0.32
3/4 7.25 7.62 8.50 3.63 3.81 4.25 2.69 1.25 0.32
1/2x1 --- --- 8.50 --- --- 4.25 2.69 1.88 0.38
3/4x1 --- --- 8.50 --- --- 4.25 2.69 1.88 0.38
1 7.25 7.75 8.50 3.62 3.88 4.25 3.62 1.88 0.38
1-1/2 8.75 9.25 9.50 4.38 4.62 4.75 4.25 2.25 0.38
2 10.00 10.50 11.50 5.00 5.25 5.75 4.81 2.75 0.38
3 11.75 12.50 14.00 5.88 6.25 7.00 6.38 3.69 0.50
4 13.88 14.50 17.00 6.94 7.25 8.50 7.69 4.44 0.50
1. All Design CP control valves have integral flanges, but are offered in the longer separable flange face-to-face dimensions that are listed in ISA S75.20.
A
A6735/IL
Figure 7. Dimensions
13
Bulletin 51.1:CP
VALVE A B
SIZE, Std Std Long Long Std Std Long Long D G
INCHES Class 150 Class 300 Class 150 Class 300 Class 150 Class 300 Class 150 Class 300
mm
1/2x1 --- --- 215.9 215.9 --- --- 108.0 108.0 284.2 47.8
3/4x1 --- --- 215.9 215.9 --- --- 108.0 108.0 284.2 47.8
1 184.2 196.9 215.9 215.9 91.9 98.6 108.0 108.0 284.2 47.8
1-1/2 222.3 235.0 241.3 241.3 111.3 117.3 120.7 120.7 284.2 57.2
2 254.0 266.7 292.1 292.1 127.0 133.4 146.1 146.1 349.3 69.9
3 298.4 317.5 355.6 355.6 149.4 158.7 177.8 177.8 492.3 93.7
4 352.6 368.3 431.8 431.8 176.3 184.1 215.9 215.9 528.6 112.8
Inches
1/2x1 --- --- 8.50 8.50 --- --- 4.25 4.25 11.19 1.88
3/4x1 --- --- 8.50 8.50 --- --- 4.25 4.25 11.19 1.88
1 7.25 7.75 8.50 8.50 3.62 3.88 4.25 4.25 11.19 1.88
1-1/2 8.75 9.25 9.50 9.50 4.38 4.62 4.75 4.75 11.19 2.25
2 10.00 10.50 11.50 11.50 5.00 5.25 5.75 5.75 13.75 2.75
3 11.75 12.50 14.00 14.00 5.88 6.25 7.00 7.00 19.38 3.69
4 13.88 14.50 17.00 17.00 6.94 7.25 8.50 8.50 20.81 4.44
1/4-18 NPT
PLUGGED
2 PLACES
17B1274-B*A/IL
Figure 8. Dimensions for Design CP Valves with ENVIRO-SEAL Bellows Seal Bonnet
14
Bulletin 51.1:CP
Specifications for 1/2 and 3/4-Inch Design CP
Valve Sizes Port Diameters
J 1/2, and J 3/4 For 1/2-Inch Valve: 9.5 mm (3/8-inch)
End Connection Styles For 3/4-Inch Valve: 14.3 mm (9/16-inch)
Raised-face integral flanges to mate with Class 150
or 300 flanges Valve Plug Restrictions
Multiple Face-To-Face Offering 70% and 40% of full capacity
Standard: ISA-S75.03 and IEC 60534-3-1 Maximum Valve Plug Travel
(interchangeable with Design E) 12.7 mm (0.5 inch)
Long: ISA-S75.20 (All Design CP control valves Bonnet Styles
have integral flanges, providing replacement for
separable flange and other long face-to-face valves) Plain
Maximum Inlet Pressures and Temperatures(1) Packing Arrangements
CF3M (316L Stainless Steel) Valve Body: Live-loaded ENVIRO-SEAL Double PTFE V-Ring
Consistent with applicable Class J 150 or J 300 meets the Fugitive Emission Standard of 500
pressure-temperature ratings per ASME B16.34, PPM(2); also see figure 2
limited to the 232_C (450_F) limit of PTFE packing
Packing Construction Materials
Maximum Pressure Drops(1) PTFE Packing Systems
Full ANSI rating to 232_C (450_F) Packing Ring: PTFE V-ring(3)
Male and Female Adaptor Rings: Carbon-filled
Shutoff Classification Per ANSI/FCI 70-2 PTFE V-ring
and IEC 60534-4 Anti-Extrusion Washer: Filled PTFE
J Class IV or J Class V (Optional) Packing Spacer: S31603 (316 stainless steel)
Construction Materials Springs: Inconel
See table 12 Packing Nut: Nitronic 60
Material Temperature Capabilities(1) Yoke Boss and Stem Connection Diameters for
Actuator Mounting
Valve Body-Trim Combinations: See table 12
Other Parts: See table 12 1/2 and 3/4 inch Sizes: 28.6 mm (1-1/8 inch) yoke
boss, 7.9 mm (5/16-inch) stem with 7.9 mm
Flow Characteristics/Valve Plug Styles (5/16-inch) stem connection
Full-Size and Restricted-Capacity Trims: Approximate Weights (with plain bonnet)
J Linear or J equal percentage
VALVE WEIGHT
Flow Direction kg Pounds
SIZE,
Flow up only INCHES Class 150 Class 300 Class 150 Class 300
Flow Coefficients and Noise Levels 1/2 4 4 8 9
See Fisher Catalog 12 3/4 4 5 8 11
1. The pressure or temperature limits in this bulletin and any applicable code limitations should not be exceeded.
2. The Environmental Protection Agency (EPA) has set a limit of 500 parts per million (ppm) for fugitive emissions from a valve in selected VOC (Volatile Organic Compound) services.
3. In vacuum service, it is not necessary to reverse the ENVIRO-SEAL PTFE packing rings.
15
Bulletin 51.1:CP
Specifications for 1/2x1- through 4-Inch Design CP
Valve Sizes Cavitrol III Cage: Linear
J 1/2x1, J 3/4x1, J 1, J 1-1/2, J 2, J 3, and Whisper Trim Seat Ring Retainer: J Linear or
J 4-inch J equal percentage
End Connection Styles Flow Direction
Raised-face integral flanges to mate with Class 150 Standard Seat Ring Retainer
or 300 flanges Fail Open: Always flow up
Fail Closed: Flow up is preferred. However, flow
Multiple Face-To-Face Offering down is acceptable in applications where fluid
Standard: ISA-S75.03 and IEC 60534-3-1 closing forces are used to help close the valve. Flow
(interchangeable with Design E) down requires the use of a double-acting piston
Long: ISA-S75.20 (All Design CP control valves have actuator such as the Type 585C.
integral flanges, providing replacement for separable Cavitrol III Cage: Flow down
flange and other long face-to-face valves) Whisper Trim Seat Ring Retainer: Flow up
Maximum Inlet Pressures and Temperatures(1) Flow Coefficients and Noise Levels
WCC Steel, LCC Steel, CF3M (316L Stainless See Fisher Catalog 12
Steel), and CF3 (304L Stainless Steel) Valve
Bodies: Consistent with applicable Class J 150 or Port Diameters
J 300 pressure-temperature ratings per ASME See table 14
B16.34 unless limited by pressure drop capabilities Maximum Valve Plug Travel
in tables 4 and 6 and figure 3 or temperature See table 14
capabilities in tables 11 and 13
Bonnet Styles
M35-1 (Monel), CW2M (Hastelloy C), N7M
(Hastelloy B), and CN7M (Alloy 20) Valve Plain
Bodies: Maximum inlet pressures and Packing Arrangements
temperatures are listed in table 1 unless limited by Standard Material: Double PTFE V-ring packing
pressure drop capabilities in tables 4 and 6 and Optional Materials: See table 13
figure 3 or by temperature capabilities in tables 11 ENVIRO-SEAL Packing: See the ENVIRO-SEAL
and 13 Packing System Specifications and figure 4. Also
Maximum Pressure Drops(1) see Bulletin 59.1:061 for further information
Valve with Standard Seat Ring Retainer Yoke Boss and Stem Connection Diameters for
Metal Seat: See table 4 Actuator Mounting
Composition Seat: See table 6 and figure 3 1/2x1-, 3/4x1-, 1, and 1-1/2 inch Sizes:
Valve with Cavitrol III Cage 54 mm (2-1/8 inch) yoke boss, 12.7 mm (1/2-inch)
Metal Seat: See table 3 stem with 9.5 mm (3/8-inch) stem connection
Valve with Whisper Trim Seat Ring Retainer 2-inch Sizes: 54 mm (2-1/8 inch) yoke boss, 15.9
Metal Seat: See table 2 mm (5/8-inch) stem with 9.5 mm (3/8-inch) stem
Composition Seat: See table 5 connection
Shutoff Classification Per ANSI/FCI 70-2 3-inch Size: 71 mm (2-13/16 inch) yoke boss, 25.4
and IEC 60534-4 mm (1-inch) stem with 12.7 mm (1/2-inch) stem
J Class IV or J Class V (Optional) for metal seats, connection
and J Class VI for composition seats 4-inch Size: 71 mm (2-13/16 inch) yoke boss, 31.8
mm (1-1/4-inch) stem with 12.7 mm (1/2-inch) stem
Construction Materials connection
See tables 7, 8, 9, 10, and 13
Approximate Weights
Material Temperature Capabilities(1)
VALVE SIZE, KILOGRAMS POUNDS
Valve Body-Trim Combinations: See table 11 INCHES Class 150 Class 300 Class 150 Class 300
Other Parts: See table 13
1/2x1, 3/4x1, 1 8 9 17 20
Flow Characteristics/Valve Plug Styles 1-1/2 11 15 25 32
Full-Size and Restricted-Capacity Trims: 2 16 19 35 42
J Linear or J equal percentage 3 35 41 77 90
Micro-Flow Valve Plugs: Linear 4 54 63 120 140
1. The pressure or temperature limits in this bulletin and any applicable code limitations should not be exceeded.
16
Bulletin 51.1:CP
ENVIRO-SEAL Packing System Specifications
Packing Arrangements Construction Materials
1/2 and 3/4-Inch Valves PTFE Packing Systems
J ENVIRO-SEAL PTFE Packing Ring: PTFE V-ring(3)
Male and Female Adaptor Rings: Carbon-filled
1/2x1- through 4-Inch Valves PTFE V-ring
J ENVIRO-SEAL Double PTFE V-Ring Anti-Extrusion Washer: Filled PTFE
J ENVIRO-SEAL Single Graphite Lantern Ring: S31600 (316 stainless steel) or alloys
J ENVIRO-SEAL Duplex - PTFE V-Ring and Springs: Inconel
Graphite (API 589 firetest) Follower: PTFE-lined S31600 or alloys
Lower Bushing: PTFE-lined S31600 or alloys
Pressures and Temperatures(1) Packing Box Studs: Strain-hardened 316 stainless
steel
To Meet the Fugitive Emission Standard of 500 Packing Box Nuts: 316 stainless steel SA194 Grade
PPM(2) 8M
For ENVIRO-SEAL PTFE and graphite packing Graphite Packing Systems
systems: See bulletin 59.1:062, Packing Selection Packing Ring: Graphite
Guidelines for Sliding-Stem Valves Springs: Inconel
For ENVIRO-SEAL Bellows Seal Bonnets: See Follower: PTFE-lined S31600 or alloys
bulletin 59.1:070, ENVIRO-SEAL Bellows Seal Lower Bushing: Carbon
Bonnets Packing Box Studs: Strain-hardened 316 stainless
For Nonenvironmental Service steel
Lower Bushing: Carbon
For ENVIRO-SEAL PTFE and graphite packing Packing Box Nuts: 316 stainless steel SA194 Grade
systems: May be used for higher pressures in 8M
non-environmental service. See bulletin 59.1:062, Bellows Seal Bonnets (1/2x1- through 4-Inch
Packing Selection Guidelines for Sliding-Stem Valves Only): See bulletin 59.1:070,
Valves ENVIRO-SEAL Bellows Seal Bonnets
1. Refer to the valve specifications in this bulletin for pressure/temperature limits of valve parts. Do not exceed the pressure/temperature rating of the valve. Do not exceed any applicable code
or standard limitation.
2. The Environmental Protection Agency (EPA) has set a limit of 500 parts per million (ppm) for fugitive emissions from a valve in selected VOC (Volatile Organic Compound) services.
3. In vacuum service, it is not necessary to reverse the ENVIRO-SEAL PTFE packing rings.
17
Bulletin 51.1:CP
This product may be covered by one or more of the following patents: 5,129,625; 5,131,666; 5,056,757; 5,230,498; and 5,299,812 or under pending patents.
Cavitrol, ENVIRO-SEAL, FIELDVUE, Fisher, Fisher-Rosemount, FloVue, and Whisper Trim are marks owned by Fisher Controls International, Inc. or Fisher-Rosemount Systems, Inc. All
other marks are the property of their respective owners.
EFisher Controls International, Inc. 1995, 2001; All Rights Reserved
The contents of this publication are presented for informational purposes only, and while every effort has been made to ensure their accuracy, they are not to be construed as warranties or guarantees, express
or implied, regarding the products or services described herein or their use or applicability. We reserve the right to modify or improve the designs or specifications of such products at any time without notice.
18
Printed in U.S.A.