Professional Documents
Culture Documents
瓷砖胶说明书
瓷砖胶说明书
1. Products Descriptions
Flexible Adhesive is a single component cement based flexible and repaid setting adhesive which
consists of selected high-quality natural inorganic mineral raw materials , flexible adhesive for
fixing all types of ceramic, porcelain tiles, mosaics and moisture stable natural stone.
2. Technical Data
Test items Technical Parameter
Tensile adhesive strength (7D) / MPa ≥0.6
Tensile adhesive strength (28d) / MPa ≥0.6
Open time, 10min tensile strength (7d) / MPa ≥0.5
Open time, 10min tensile strength (28d) / MPa ≥0.5
Compression ratio (28d) ≤3.0
Construction parameters
Project Technical Parameter
Gouache ratio 0.22-0.24:1
product status White powder
Construction temperature 5-35℃
Operational time 2h
Time required to withstand the load ≥24h
Dry density 1500kg/m³
Time required to withstand the load ≥24h
Dry density 1500kg/m³
3. Application
It is used to fix porcelain tiles, marbles, natural granites, natural stones, travertine,pool tiles
and pieces, and non-slip tiles.
Fix tiles onto concrete, cement renders/screeds, block work, rendered brickwork, fibre
cement sheet and particular waterproofing membranes.
For both interior and exterior applications.
4. Features:
Has strong cohesion force. Reduce the common phenomenon of tiles detaching and peeling
when pasted by Portland cement.
Be premixed and produced, the product is stable, water and used, to protect the constructio
n environment.
Tile adhesive specification
Has strong water retention, no need to dip tiles and wet walls, thin construction, easy opera
tion, to reduce material consumption and building load.
Has good flexibility to resist effectively the destruction of various stresses.
Has special formula to avoid completely the common phenomenon of tiles cracking, detachi
ng and peeling by Portland cement.
It is no-toxic, no-radiation, no smell and environmental.
Has special formula to prevent the flow with too much southbound crash, easier constructio
n.
5.Shelf Life
Products can be stored up to 12 months in an elevated, cool dr yplace in original packaging.
Tile back glue coating primer specification
1. Products Description
The vitrified tile back glue coating primer is composed of powders and liquid materials. Powders are
blended from high quality cement, refined sands and modifiers; liquid materials are blended from
imported polymer emulsions, modifiers, etc. The product is used in back coating interface treatment of
low water absorption vitrified tiles and can release the majority of the stress generated between tile
glue and vitrified tiles. The product has a very good transition effect on bonding between common tile
glue and vitrified tiles and can effectively eliminate the phenomena such as hollowing and falling of
vitrified tiles.
2. Application Scope
Applicable to the back coating primer of glazed tiles, through-body tiles, polished tiles, polished glazed
tiles, thin slab tiles, vitrified tiles, anti-slip tiles, ancient bricks, mosaics, marble, granite, slate, etc.
3. Products Features
Good permeability,
High initial viscosity,
High water and alkali water resistance,
Good weather resistance
Tile back glue coating primer specification
4. Construction Method
Backsurface Clean
5. Storage
This product should be transported and stored at 5-30 ℃, and the storage temperature is valid
for 6 months at 25 ℃; below 0 ℃, it will freeze and solidify and cannot be restored. If stored at
sub-zero temperature, please take good thermal insulation measures;
1. Products Descriptions
Double-component epoxy adhesive for ceramic tile gap filler, mainly use epoxy resin, curing agent and high-grade
pigment as raw material, adopt advanced technology. Developed from epoxy resin polymer has advantages, such
as bright appearance, high hardness after curing, anti-mildew, anti-bacteria, easy cleaning, anti-scrubbing and so
on. It can effectively solve the problem of black and yellow ceramic tile seams and difficult to clean.
4. Application Procedures
1. Production Descriptions
Fiber cement board is a stable performance and light weight building & decoration board used cement as major and natural
reinforced, with the process of pulping, emulsion,forming, pressing, autoclaving ,drying and surface treatment.The color is gray.
With the sanding surface, thickness uniformity is better and grain is clearer. And because of the cement , the strength is higher,
and water proof performance is much better.So fiber cement board is the highest quality product in domestic and foreign building
materials market .
2. Product characteristics
Density : 1.2-1.5G/CM3
Fire-proof Rate : A-Class incombustible (GB8624-1997)
In-combustibility (min): 240 minutes (GB/T9978-1999)
Water content : ≤30%
Swelling ratio: ≤0.4%
Anti-bending Strength: ≥16MPA
Frost resistance : Don't appear cracking and delamination after 25 cycles of freezing and thawing . (GB/T7019-1997)
Radioactivity: standard of GB6566-2001 (A-class Decoration Materials).
3. Recommended application:
Partition board, exterior wall cladding , panel, suspended ceilings ,light weight grouting panel, interior dry wall decoration
board ,interior wall after painting and coating .
1. FLAME RESISTANT BOARD
Product Category:Flame Retardant Block Board, Flame Retardant Decorative Board And Flame Retardant Board Plywood
Environmental Grade:E0
TREEZO Green Environmental Flame Retardant Board Is Made Of High Quality Log Veneer As Raw Material, Which Is Processed By
Flame Retardant Treatment, Drying, Bonding, Cold Pressing, Hot Pressing And So On. Its Performance Of Flame Retardant, Smoke
Suppression And Smoke Toxicity Reach The National B Grade Flame Retardant Materials Requirements - 8624-2012 GB Building
Materials And Products, Combustion Performance Classification," At The Same Time To Meet The Requirement Of National Standard
20286-2006 GB "Public Places Flame Retardant Products And Components Of The Combustion Performance Requirements And
Labeling". It Also Maintains Excellent Physical Properties, Processing Performance And Decorative Features Of Traditional Artificial
2. Application Range:
Mainly Used For Public Construction And Renovation Project, High-End Construction And Renovation Project And High-Grade
Furniture Production Project, Such As Hotels, Restaurants, Meeting Centers, Exhibitions, Sports Centers, Libraries, Passenger
Product Characteristics:
4. Good Processing Performance, Good Function Of Thermal Insulation, Sound Absorption, Sound Insulation.
5. Smooth Surface, Strong Durability And Not Easy To Aging And Weathering.
GN1001 rice glue is environmental friendly wallpaper adhesive which made of sticky rice and waxy corn. It’s
made by 12 procedures like purification, grinding, drying and so on. Sticky rice glue has wide range of application,
which is high-performance wallpaper and wall cloth bonding material with high viscosity.
2. Product advantages
3. Main composition
Sticky Rice Glue: sticky rice Starch, waxy corn starch, water and Nacl.
5. Application Instruction
Note: (1).All the above data is just for reference. Please adjust the ratio depending on the weight of wallpaper.
(2)If you think glue is too thick,can add less than 20% water for solution,notice not over-dissolved.
(4)Keep the product away from children and dispose the package complying with the local environmental regulations.
6. Application Scope
It can be used to paste all kinds of wallpaper and wall cloth, especially pure paper wallpaper and
golden foil wallpaper which have higher construction requirement. It is widely used in home and
high-end villa decoration.
7 . Storage Condition
Best storage condition: in 5~30℃ cool and dry environment, avoiding direct sunlight
Product Details GM-06
It can form protective layer to prevent the base surface from falling off and the surface plane from acid-base leakage, can also
increase the adhesive force between wallpaper and wall base surface, meanwhile playing a role in moisture-proof and
anti-mildew.
Product features:
Usage:
1. Dilution:
Add 30%~70% water per Liter according to the wall absorption and climatic conditions.
2. Drying time:
3. Application:
Expiration Date:
12 months
Application scope:
Apply for all kinds of metope, such as putty powder wall metope, light calcium and heavy calcium porous wall, composite
Storage:
木挂件(固定于轻钢龙骨)
墙布
木饰面&硬包
天花完成面
发泡胶 原结构梁
双层12mm厚纸面石膏板
双层12mm厚纸面石膏板
(梁中线) (梁中线)
JDG20线管走向示意
20*50*0.7mm轻钢龙骨及卡件
插座底盒做法示意 双层12mm厚纸面石膏板(至板底)
60kg/m3/ 吸音岩棉
插座底盒做法示意
砌块墙/结构墙
轻质砌块墙 墙布
20*50*0.7mm轻钢龙骨及卡件
轻钢龙骨卡件
地脚线(详立面)
地脚线(详立面) 地脚线(详立面)
地面(详地材平面)
地面(详地材平面) 地面(详地材平面)
60kg/m3/
吸音岩棉
墙体 墙体
地面(详地材平面) 地面(详地材平面)
木挂件 木挂件
木饰面板 墙布
木饰面&硬包
木饰面&硬包&镜子
双层12mm厚纸面石膏板
插座底盒做法示意
插座底盒做法示意
12mm厚难燃夹板
12mm厚难燃夹板
轻质砌块墙
墙布
20*50*0.7mm轻钢龙骨及卡件
木饰面
60kg/m3/ 吸音岩棉
基膜
双层12mm厚纸面石膏板
12mm厚难燃夹板
20mm厚批荡找平层
12mm厚难燃夹板
轻质砌块墙 界面剂
硬包
20*50*0.7mm轻钢龙骨及卡件 砌块墙/结构墙
木挂件
地脚线(详立面)
地脚线(详立面)
地脚线(详立面)
地面(详地材平面) 地面(详地材平面) 地面(详地材平面)
水泥砂浆找平
Applications DOWSIL™ 796 Neutral Silicone is a one-part, low modulus, neutral curing silicone
sealant specifically developed for the sealing of PVC-U, glass, glazed surfaces and
brickwork. It is very popular for perimeter sealing applications of windows and doors.
Typical Properties
Specification Writers: These values are not intended for use in preparing specifications.
Note: When using any solvent, always provide adequate ventilation. Avoid heat, sparks and
open flames. Use solvent resistant gloves. Observe and follow all precautions listed on
solvent container label.
Masking
Areas adjacent to the joints should be masked with tape to prevent contamination of the
substrates and to ensure a neat sealant line. Masking tape should be removed immediately
after tooling.
Priming
No primer is required for PVC-U and for most common construction substrates including
brick. However, a test placement prior to general use is always recommended.
Back-up Materials
Closed cell polyethylene backer rod is recommended as a back-up material to provide back
pressure and avoid three sided adhesion that limits sealant movement capability. Low tack
polyethylene tape should be used in joints too shallow to allow the use of backer rod.
Finishing
The joint should be tooled within 5 minutes of application to ensure good contact between
the sealant and the substrate. Tooling of the sealant also gives a smooth, professional
finish.
Clean-up
Excess sealant may be cleaned off tools and non-porous surfaces whilst in an uncured state
using DOWSIL™ R-40 Universal Cleaner. If sealant is misapplied to porous substrates, it
should be left until it is just cured and then removed by peeling, cutting or other mechanical
means. Care should be taken not to damage plastic or coated surfaces.
Joint Design The sealant joint width should be designed to accommodate the movement capability of the
sealant. When designing joints using DOWSIL™ 796 Neutral Silicone, the minimum width
should be 6 mm. For joints between 6–12 mm wide, a seal depth of 6 mm is required. For
joints above 12 mm wide, a width to depth ratio of 2:1 should be used. For joint dimensions
greater than 25 mm, please contact your regional service center for technical assistance. In
situations where fillet joints are needed, a minimum of 6 mm sealant bite to each substrate
is recommended.
Handling PRODUCT SAFETY INFORMATION REQUIRED FOR SAFE USE IS NOT INCLUDED IN
Precautions THIS DOCUMENT. BEFORE HANDLING, READ PRODUCT AND SAFETY DATA SHEETS
AND CONTAINER LABELS FOR SAFE USE, PHYSICAL AND HEALTH HAZARD
INFORMATION. THE SAFETY DATA SHEET IS AVAILABLE ON THE DOW WEBSITE AT
DOW.COM, OR FROM YOUR DOW SALES APPLICATION ENGINEER, OR
DISTRIBUTOR, OR BY CALLING DOW CUSTOMER SERVICE.
Usable Life and When stored at or below 30°C (86°F) in the original unopened containers, DOWSIL™ 796
Storage Neutral Silicone has a usable life of 12 months from the date of production.
Limitations DOWSIL™ 796 Neutral Silicone is not recommended for structural glazing or insulated
glazing applications. Do not use DOWSIL™ 796 Neutral Silicone on bituminous substrates,
substrates based on natural rubber, choloroprene or EPDM or on building materials which
might bleed oils, plasticisers or solvents. Do not use DOWSIL™ 796 Neutral Silicone in a
totally confined space because the sealant requires atmospheric moisture to cure. It is not
recommended for use on submerged joints, or in joints where physical abuse or abrasion are
likely to occur. Bleeding can occur on porous substrates, such as concrete, marbles, granites
and other natural stones. Specific testing should be carried out on sensitive substrates.
DOWSIL™ 796 Neutral Silicone is not suitable for food contact applications.
It is recommended that DOWSIL™ 796 Neutral Silicone is not applied to surfaces that are
below 5°C (41°F) as it is impossible to guarantee a dry surface at these temperatures.
This product is neither tested nor represented as suitable for medical or pharmaceutical
uses.
Health and To support customers in their product safety needs, Dow has an extensive Product
Environmental Stewardship organization and a team of product safety and regulatory compliance specialists
available in each area.
Information
For further information, please see our website, dow.com or consult your local Dow
representative.
It is the user’s responsibility to verify that treatment and disposal procedures comply with
local, state (provincial) and federal regulations. Contact your Dow Technical Representative
for more information.
Product Dow has a fundamental concern for all who make, distribute, and use its products, and for
Stewardship the environment in which we live. This concern is the basis for our product stewardship
philosophy by which we assess the safety, health, and environmental information on our
products and then take appropriate steps to protect employee and public health and our
environment. The success of our product stewardship program rests with each and every
individual involved with Dow products - from the initial concept and research, to manufacture,
use, sale, disposal, and recycle of each product.
Customer Notice Dow strongly encourages its customers to review both their manufacturing processes and
their applications of Dow products from the standpoint of human health and environmental
quality to ensure that Dow products are not used in ways for which they are not intended or
tested. Dow personnel are available to answer your questions and to provide reasonable
technical support. Dow product literature, including safety data sheets, should be consulted
prior to use of Dow products. Current safety data sheets are available from Dow.
dow.com NOTICE: No freedom from infringement of any patent owned by Dow or others is to be inferred. Because use conditions and
applicable laws may differ from one location to another and may change with time, Customer is responsible for determining
whether products and the information in this document are appropriate for Customer's use and for ensuring that Customer's
workplace and disposal practices are in compliance with applicable laws and other government enactments. The product shown
in this literature may not be available for sale and/or available in all geographies where Dow is represented. The claims made
may not have been approved for use in all countries. Dow assumes no obligation or liability for the information in this document.
References to "Dow" or the "Company" mean the Dow legal entity selling the products to Customer unless otherwise expressly
noted. NO WARRANTIES ARE GIVEN; ALL IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A
PARTICULAR PURPOSE ARE EXPRESSLY EXCLUDED.
Page 5 of 5 ®Trademark of The Dow Chemical Company Form No. 62-1815-01-0920 S2D
Technical Data Sheet
Applications DOWSIL High Performance Kitchen and Bathroom Mould Resistant Sealant is
designed to resist the growth of mildew where conditions of high humidity and
temperature exist.
Typical applications include the sealing around the shower room, bathtub, toilets, wash
basin in kitchen and bathroom.
Typical Properties
Specification Writers: These values are not intended for use in preparing specifications.
Back-up Materials
At the bottom of the joint, use backer rod (e.g. closed-cell type polyethylene or open-cell
polyurethane foams) or equivalent material (e.g. low-viscosity polyethylene tape) to control
the depth of sealant. Avoid 3-sided adhesion by preventing the sealant from adhering to the
bottom of the joint.
Tool the joint surface as soon as the sealant is applied, keeping the surface smooth
and flat, and ensuring that the edge of the joint is full of sealant.
Complete the tooling before the sealant skin forms (e.g. in working time). Convex-
surface tools are recommended for tooling to allow the joint to remain full of sealant.
Tooling must be performed when sealing the horizontal joint to prevent any liquid (e.g.
rainwater and cleaner) from staying on the sealant surface.
Do not use soap or water as tooling assistants.
After the tooling and before the sealant cures, remove masking tape.
Do not touch the surface of the sealant within the 48 hours following its cure. Avoid
sealant contact with cleaner or solvent (e.g. bleaching agent) during this period.
When a flammable solvent is used, proper precautions should be applied. For porous
material surfaces, allow the sealant to cure completely before removing the masking
tape. Cured sealant can be removed with a knife.
The sealant releases gas during curing; the odor disappears after it is cured. The
completely cured sealant is harmless.
Sealant Filling
Cut the nozzle at an angle of 45° depending on the shape and specification needed.
Tighten the nozzle onto the sealant tube. Put the sealant tube into the cartridge gun. Use
pneumatic or manual cartridge gun. Apply sealant to the bottom of the joint to fill the joint
completely and to ensure adhesion to both sides of the joint. Do not apply the sealant
simply on the surface as the sealant cannot fully fill the joint by gravity.
Joint Design Proper joint design can reduce the stress on the sealant and help obtain optimal sealant
movement capability, improve the ease of application, reduce cohesive failure, and
minimize the effects of curing byproducts.
Usable Life and When stored at or below 30°C in original unopened containers, this product has a usable life
Storage of 12 months from the date of production.
Packaging This sealant is supplied in 300 ml cartridges, 24 cartridges per carton. Please contact your
Information local Dow sales office for related information.
Aquarium
Continuous water immersion
Food contact applications
Totally confined space
Structural glazing or insulated glazing
The joints where physical abuse or abrasion are likely to occur
Cannot be painted, as paint will not adhere to sealant
Materials that bleed plasticizers or solvents or release by-products that may inhibit its
cure, affect adhesion or discolor the sealant.
This product is neither tested nor represented as suitable for medical or pharmaceutical
uses.
Health and To support customers in their product safety needs, Dow has an extensive Product
Environmental Stewardship organization and a team of product safety and regulatory compliance specialists
available in each area.
Information
For further information, please see our website, dow.com or consult your local Dow
representative.
Dow’s sole warranty is that our products will meet the sales specifications in effect at the time of shipment.
Your exclusive remedy for breach of such warranty is limited to refund of purchase price or replacement of any product shown
to be other than as warranted.
TO THE FULLEST EXTENT PERMITTED BY APPLICABLE LAW, DOW SPECIFICALLY DISCLAIMS ANY OTHER
EXPRESS OR IMPLIED WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE OR MERCHANTABILITY.