QUICK INSTALLATION GUIDE1.0 Overall parts as follow:
PL
“aS” 8 hT
The uppar—Thebotiom —Baltay Frontmotr Rear motor Powe Samping Antenna
tmanboard mainboard fiedslato fed plato —_fxed pate. Board bal st fied mount
Body Part :
{total 28 pes) AL. |
= Ie Sea fi
ae om a5 ff Pe se l
The camera Decorato Fixed Support support Propelrs{OW Skd_————Support__ Antenna
fod plato x2 part block block frame and COW)x2_landing x4 pilar easing
uvenpt| GP SP BP gr |S o
(total 15 pes) 5.86 Receiver Main Brushless Mushroom Red Motor(CW
itor Contr ESCx4 antenna Camera ightx2_—_ and Cow) x2
|r ~ t & & &
(total 68 pes) 14 pes of 10 pes of 2 pes of 12 pes of 14 pcs of 16 pes of
Poexr Pobre Pete None Nae owe
Supplemental S—— A5 CJ
material — — > Ge
(tota 5 pes)
M1.SHex Wrench 2.0 Hex Wrench Mushroom antenna wrench Velero strap Battery anté-slip mat2.0 Install brushless ESC(CW/CCW), Power Board and motor fixed plate
> NO.1 Install One end of brushless ESC(CWICCW)
into power board, install the other end into motor
fixed plate, then fix both sides by screw (PB2x7)
> NO.2 Fix the white LED light to Front motor fixed
plate by scrow (PB2x7)
T
Parts needed for this step
The assembling method for
the 4 pes of brushless ESC is same.
Front motor Rear motor Power Brushless 6 pos of
fixed plate fixed plate Board ESCX4 — PB2xT
we3.0 Install the bottom main board
Fix the bottom main board with screw (M2x4/M2x8)
The bottom 2 pes of 8 pos of
mainboard 2x4 screws M2x8 screws4.0 Assemble Skid landing , video camera, support block and battery fixed plate
D> No.1 Fix the video camera on support block with screw (M2x4).
> NO.2 Fix the video camera subassembly and 4 pes of skid landing onto the battery fixed plate with screw (PB2x7)
(a
Battery Suppor Video skid Spesof — 2pesof
fixed plate block Camera landing x4 PB2x7 Mx
“45.0 Assemble support frame and skid landing subassembly
fl Fix the support frame and skid landing subassembly
ql onto the body with screw(PB2x14).
frame PB2x14 screws:6.0 Assemble receiver, Main Controller and 5.8G emitter
name
[- -|
4 =
wien cars)
“The metal suriace of fat cable
lug shouldbe inserted pwr
formain contol pot propery.
‘The metal srtace of exible at cable
plug shoul be insotes downward to
power board por propery
When installing
the receiver and Main
Controller, the metal surface of flexible
flat cable(FFC) should be inserted upward
properly and fastened then fix it onto the power board with
double side tape. Put the 5.8G emitter onto the power board
with screw (M2x8), and then install the mushroom antenna.
Mushroom TXS816 or TXS817-«;DEVO-RX710._«—=FCS-RUNNER250 4 pcs of
antenna emitter Receiver Main Contraler M2x8 serews
67.0 Install fixed block, decorate part and Red LED light
D> NO. Fix the Decorate part onto main boty part with screw (PB2x14), then insert,
the connecting wire on the camera socket(3pins!t1.1V) of power boar
D> NO.2 Fx the fixed black ent the main body
with screw (PB1 736).
D> NO‘ Insert ho wir fred indicator Ih ito
Power board pot then fit tthe main body.
by screw (PB2x7)
Parts needed for this step
Decorate «Red LED ined
part light x2 block
Battery plu 2 pes of 2pcsot 2s of
~ Banery Pus PoiTxs = -PBaxT Paani8.0 Install the upper main board and camera fixed plate.
> NO.1 Fix the Support pillar to the
upper main board by screw (M2x4),
> NO.2 Fix the upper main board and
camera fixed plate by screw(M2x4),
then put on the damping balls.
D> NO.3 Use the screw (M2x8) to fix both
from the inner side.
Parts needed for this step
=
The camera vibration
fixed plate x2 damping ball x4
| t f
The upper Support Bpesof 2 pes of
main board pillar = M24 M289.0 Install the motor
Fix the clockwise and counterclockwise motor to the motor fixed plate respectively by screw (M3x6), then insert the
brushless motor wires to the port of the brushless ESC according to the red, blue, black signed ports.
WK.WS-28-014 Brushless ESC Brushless ESC WK.WS-28-014
(ecw) icetiy ic} ‘eH
oO
WKaNs.28-014 Brushless ESC Brushless ESC WKMIS 28014
ei tay ‘eet (ecw
@=0 5 {io os)
The red, blue, black wires of blushiess
‘motor should be inserted into the red,
blue, black signed ports of the bushless So
ESC accordingly. SS
Brushless Brushless 16 pos of
moto(CW) x2 motor(CCW) X2_— 3x610.0 Install propellers
Fix the clockwise propeller(white cap) onto the clockwise motor
‘according to the direction of arrow, and fix the counterclockwise
propeller(black cap) on the counterclockwise motor according to
the direction of arrow. Tighten the propellers manually and make
sure the propeller is installed in proper way and fastened.
11.0 Fixed the Receiver Antenna on rack
(1) Leading the antenna across upper main board and loading
itinto fixed mount
(2) Clipping the fixed mount in upper main board,
(@) Leading the antenna across casing and Loading the easing
into fixed mount.
WARNING: The receiver antenna has to be straightened
before the flight, to lengthen the communication distance.
Parts needed fort
Antenna Antenna
fixed mount casing
Counterclockwise
propeller
(black cap)
Clockwise propeller
(white cap)
/ clockwise propeler
ED) (white cap)
Counterclockwise)
propeller
(black cap)
“10.WW walkera
User manual is subject to change without prior notice.
Please goto Wekera oficial websie to get the lees version
.
Wer: wuwwaieracom EB CE FE