Professional Documents
Culture Documents
06 08 Lexus Is Grille Installation Manual
06 08 Lexus Is Grille Installation Manual
3
5
3. Using the flat blade screwdriver, lift up on the push pin 4. Once the push fasteners are removed, remove the plastic 5. Remove the rubber weatherstrip from across the top of
and remove it from the cover. radiator support panel cover. the painted bumper cover by stretching the weatherstrip
over the clips, leaving the clips in the bumper cover as
you could break them if you try to pry them out of their
mounting holes.
6 7
6
6. Remove the center 10mm bolt at the top center of the 6. Use needle nosed pliers to squeeze and remove the 7. Remove the top outer push pins to release the top edge
grille. weatherstripping clips from the painted bumper cover of the grille.
and reinstall them back into the holes in the weather
stripping.
8 9
10
8. Use a flat blade screwdriver to release the upper grille 9. Use a flat blade screwdriver to release the lower grille 10. Once all the clips are released, remove the factory grille
side mounting tabs (one each side). mounting tabs (located across the bottom of the upper from the bumper cover. Finish removing the factory
grille). weatherstrip across the top of the grille (to be reinstalled
onto the E&G mesh grille).
11. Place the grille onto a clean work bench and remove the 12. Using the supplied double faced tape, cut it into 1/8”
factory emblem from the factory grille. Use a plastic wide strips and apply the tape to the outside edge of
squeegee of other non-metallic tool to seperate the 13. Peel off the tape backing, align the emblem onto the
the emblem (as shown). emblem mounting plate and press firmly to set the tape.
emblem from the double faced tape securing it to the
grille. Clean off any excess double faced tape from the 14. Install the emblem assembly onto the mesh grille using
back of the emblem. the supplied black plastic washers, s.s. lock washers
and the s.s. hex nuts (not shown).
15 16 18
15. Cut out the supplied template and tape it into place on 16. Remove the template and drill through the marks made 17. Apply masking tape around the lower opening. Tape sev-
the driver side of the front bumper cover in the factory in the bumper cover with a .125” (1/8”) drill bit. Once eral additional layers at the center and lower corners of
grille opening (as shown). Use an awl or similar pointed the holes are drilled, use the drill bit to connect the the lower grille opening for added paint protection.
tool to mark the hole locations onto the driver side holes, making a mounting slot for slight right to left 18. Measure and mark the exact center of the lower grille
bumper cover. Untape the template, flip it over and mark adjustments during the grille installation. opening.
the holes on the passenger side bumper cover.
19. Align the lower grille into the factory lower opening, 21. Drill through the marks make in the previous step and
making sure that the mesh and frame are tight against align the mesh section and lower grille frame into place. 23. Install the supplied #6 x 1/2” countersunk phillips screws
the factory grille at the bottom. Insert the mounting pins on the lower grille frame into to secure the lower mesh grille into place.
20. Mark the lower mounting pin locations onto the mask- the holes, then rotate the lower grille frame back into the
ing tape and remove the frame and mesh section. lower grille opening.
22. While keeping the mesh grille tight against the factory
grille, use a 3/32” drill bit to drill through the centers of
the mounting tabs (as shown).
24
25 27
20
24. Install the upper grille into place, making sure the lower 25. Reinstall the factory push pins to secure the outer upper 27. Install the supplied #8 x 1/2” black truss head screws to
mounting pins are pressed into the slots drilled in the corners of the grille. lock the top of the grille onto the bumper cover.
Step 16. 26. Use a .125” (1/8”) drill bit to drill through the existing
hole in the top mounting plate and into the top edge of
the bumper cover.
28
28. Reinstall the factory rubber weatherstripping back onto 29. Reinstall the factory radiator support panel cover by rein- 30. Remove the masking tape around the upper and lower
the top of the E&G grille and painted bumper cover. stalling the factory push pins removed in Step 2. grilles. Carefully peel back the protective tape covering
the frames on the upper and lower grilles and use a soft,
clean cloth and solvent to remove any glue residue left by
the tape. Use alcohol or glass cleaner to remove any sol-
vent residue from the frames.
WARRANTY INFORMATION:
E&G Classics, Inc. warrants its chrome parts and products to be free from defects in mate-
rial, workmanship or finish for Twenty-Four (24) months from the date of shipment by E&G.
This warranty is limited to the repair or replacement, at E&G Classics option, of the defective
part or product. To obtain performance under this warranty you must:
1.) Present your E&G unit to an authorized distributor in your area with proof of purchase.
24 2.) If no distributor is available, contact E&G Classics (address below) for authorization to
return unit.
3.) Returns - All unauthorized returns will be refused. Merchandise approved by E&G for
return must have been purchased within the Twenty-Four (24) months. All returns require
an authorization number obtained from E&G and the actual return must be accompanied
by the written authorization form filled out completely. All merchandise most be inspect-
ed upon receipt and shortages reported within 48 hours. All merchandise must be in a
resalable condition. Merchandise must be packed carefully in the original packing. If orig-
inal packing is no longer usable, repack item(s) comparable to original manner. All returns
are subject to a 25% handling charge. Special order items are not returnable. Defective
merchandise must have an explanation of the problem. No credit will be issued unless
invoice number and date of purchase has been supplied. Manufacturer shall be sole judge
of defects in a product.
4.) UPS accounts - All returns must be prepaid. Do not send return shipments freight collect.
Once E&G has made its decision and it is a claim against our warranty policy, E&G will
credit incoming freight on damaged parts.
5.) No discontinued part or parts changed due to body style are returnable.
For Return Authorization, write or telephone: E&G Classics, Inc., 8910 McGaw Court,
Columbia, MD 21045 (410) 381-4900 Attn.: Return Department
31. Finished installation. You are responsible for inspecting all packages containing E&G Classics' parts and product
immediately upon their receipt and must file a claim with the carrier for any damage disclo-
sure by such inspection and notify E&G classics in writing at the above address of any such
damage. This warranty does not extend to any of our products which have been subject to
misuse, neglect, accident or have been altered or repaired in any way. This warranty does not
cover any accidental or consequential damages for any breach of this warranty agreement.
E&G Classics shall have no responsibility for any loss of time, inconvenience, commercial loss
or consequential damage, nor shall E&G be liable for any injury or damage to persons or prop-
erty by reason of any defect in material, workmanship or finish of its parts or products. This
warranty gives you specific legal rights and you may also have other rights which may vary
from state to state.