Professional Documents
Culture Documents
(600 Volts Peak) : Globaloptoisolator
(600 Volts Peak) : Globaloptoisolator
(600 Volts Peak)
The MOC3061, MOC3062 and MOC3063 devices consist of gallium arsenide
infrared emitting diodes optically coupled to monolithic silicon detectors
performing the functions of Zero Voltage Crossing bilateral triac drivers.
They are designed for use with a triac in the interface of logic systems to
equipment powered from 115/240 Vac lines, such as solid–state relays,
industrial controls, motors, solenoids and consumer appliances, etc.
• Simplifies Logic Control of 115/240 Vac Power
6
• Zero Voltage Crossing 1
• dv/dt of 1500 V/µs Typical, 600 V/µs Guaranteed STANDARD THRU HOLE
• To order devices that are tested and marked per VDE 0884 requirements, the
suffix ”V” must be included at end of part number. VDE 0884 is a test option.
Recommended for 115/240 Vac(rms) Applications:
• Solenoid/Valve Controls • Temperature Controls
COUPLER SCHEMATIC
• Lighting Controls • E.M. Contactors
• Static Power Switches • AC Motor Starters 1 6
• AC Motor Drives • Solid State Relays
MAXIMUM RATINGS 2 5
Rating Symbol Value Unit
ZERO
INFRARED EMITTING DIODE 3 CROSSING 4
CIRCUIT
Reverse Voltage VR 6 Volts
Forward Current — Continuous IF 60 mA 1. ANODE
2. CATHODE
Total Power Dissipation @ TA = 25°C PD 120 mW 3. NC
Negligible Power in Output Driver 4. MAIN TERMINAL
Derate above 25°C 1.41 mW/°C 5. SUBSTRATE
OUTPUT DRIVER DO NOT CONNECT
6. MAIN TERMINAL
Off–State Output Terminal Voltage VDRM 600 Volts
Peak Repetitive Surge Current ITSM 1 A
(PW = 100 µs, 120 pps)
Total Power Dissipation @ TA = 25°C PD 150 mW
Derate above 25°C 1.76 mW/°C
TOTAL DEVICE
Isolation Surge Voltage(1) VISO 7500 Vac(pk)
(Peak ac Voltage, 60 Hz, 1 Second Duration)
Total Power Dissipation @ TA = 25°C PD 250 mW
Derate above 25°C 2.94 mW/°C
Junction Temperature Range TJ – 40 to +100 °C
Ambient Operating Temperature Range TA – 40 to +85 °C
Storage Temperature Range Tstg – 40 to +150 °C
Soldering Temperature (10 s) TL 260 °C
TYPICAL CHARACTERISTICS
TA = 25°C
1.5
+800 1.4
OUTPUT PULSE WIDTH – 80 µs NORMALIZED TO
ITM , ON–STATE CURRENT (mA)
+600 IF = 30 mA 1.3
TA = 25°C
f = 60 Hz 1.2
V INH, NORMALIZED
+400
TA = 25°C
+200 1.1
0 1
–200 0.9
–400 0.8
–600 0.7
–800 0.6
0.5
–4 –3 –2 –1 0 1 2 3 4 5 –40 –20 0 20 40 60 80 100
VTM, ON–STATE VOLTAGE (VOLTS) TA, AMBIENT TEMPERATURE (°C)
500 1.5
I DRM1, PEAK BLOCKING CURRENT (nA)
1.4
200 IF = 0 1.3 IF = RATED IFT
IDRM2, NORMALIZED
1.2
100
1.1
50 1
0.9
20 0.8
0.7
10
0.6
5
–40 –20 0 20 40 60 80 100 –40 –20 0 20 40 60 80 100
TA, AMBIENT TEMPERATURE (°C) TA, AMBIENT TEMPERATURE (°C)
Figure 3. Leakage with LED Off Figure 4. IDRM2, Leakage in Inhibit State
versus Temperature versus Temperature
25
IFT, NORMALIZED LED TRIGGER CURRENT
1.3
1.2 15
1.1
1 10
0.9
0.8
0.7 5
0
–40 –20 0 20 40 60 80 100 1 2 5 10 20 50 100
TA, AMBIENT TEMPERATURE (°C) PWin, LED TRIGGER PULSE WIDTH (µs)
Figure 5. Trigger Current versus Temperature Figure 6. LED Current Required to Trigger
versus LED Pulse Width
+400
Vdc RTEST 1. The mercury wetted relay provides a high speed repeated
R = 10 kΩ pulse to the D.U.T.
2. 100x scope probes are used, to allow high speeds and
voltages.
PULSE CTEST 3. The worst–case condition for static dv/dt is established by
INPUT MERCURY triggering the D.U.T. with a normal LED input current, then
X100
WETTED removing the current. The variable RTEST allows the dv/dt to be
SCOPE
RELAY D.U.T. gradually increased until the D.U.T. continues to trigger in
PROBE
response to the applied voltage pulse, even after the LED
current has been removed. The dv/dt is then decreased until
the D.U.T. stops triggering. tRC is measured at this point and
recorded.
Vmax = 400 V
APPLIED VOLTAGE
WAVEFORM 252 V
240 Vac
R1 D1
Suggested method of firing two, back–to–back SCR’s,
1 6 with a Motorola triac driver. Diodes can be 1N4001; resis-
VCC
tors, R1 and R2, are optional 330 ohms.
Rin
2 5 SCR
MOC3061–63
SCR
360 Ω
3 4 NOTE: This optoisolator should not be used to drive a load directly.
It is intended to be a trigger device only.
D2
R2
LOAD
PACKAGE DIMENSIONS
–A–
NOTES:
6 4 1. DIMENSIONING AND TOLERANCING PER ANSI
Y14.5M, 1982.
–B– 2. CONTROLLING DIMENSION: INCH.
3. DIMENSION L TO CENTER OF LEAD WHEN
1 3 FORMED PARALLEL.
INCHES MILLIMETERS
DIM MIN MAX MIN MAX
F 4 PL C L A 0.320 0.350 8.13 8.89
N B 0.240 0.260 6.10 6.60
C 0.115 0.200 2.93 5.08
D 0.016 0.020 0.41 0.50
E 0.040 0.070 1.02 1.77
F 0.010 0.014 0.25 0.36
–T– K G 0.100 BSC 2.54 BSC
SEATING J 0.008 0.012 0.21 0.30
PLANE
G J 6 PL K 0.100 0.150 2.54 3.81
L 0.300 BSC 7.62 BSC
M 0.13 (0.005) M T B M A M
M 0_ 15 _ 0_ 15 _
E 6 PL
N 0.015 0.100 0.38 2.54
D 6 PL
0.13 (0.005) M T A M B M STYLE 6:
PIN 1. ANODE
2. CATHODE
3. NC
4. MAIN TERMINAL
5. SUBSTRATE
6. MAIN TERMINAL
THRU HOLE
–A–
6 4
–B– S NOTES:
1. DIMENSIONING AND TOLERANCING PER ANSI
1 3
Y14.5M, 1982.
2. CONTROLLING DIMENSION: INCH.
INCHES MILLIMETERS
L DIM MIN MAX MIN MAX
F 4 PL
H A 0.320 0.350 8.13 8.89
B 0.240 0.260 6.10 6.60
C 0.115 0.200 2.93 5.08
C D 0.016 0.020 0.41 0.50
E 0.040 0.070 1.02 1.77
–T– F 0.010 0.014 0.25 0.36
G G 0.100 BSC 2.54 BSC
J SEATING
H 0.020 0.025 0.51 0.63
PLANE
E 6 PL K 6 PL J 0.008 0.012 0.20 0.30
K 0.006 0.035 0.16 0.88
D 6 PL 0.13 (0.005) M T B M A M
L 0.320 BSC 8.13 BSC
S 0.332 0.390 8.43 9.90
0.13 (0.005) M T A M B M
SURFACE MOUNT
MOC3061, MOC3062, MOC3063
–A– NOTES:
1. DIMENSIONING AND TOLERANCING PER ANSI
Y14.5M, 1982.
2. CONTROLLING DIMENSION: INCH.
6 4 3. DIMENSION L TO CENTER OF LEAD WHEN
FORMED PARALLEL.
–B–
1 3 INCHES MILLIMETERS
DIM MIN MAX MIN MAX
A 0.320 0.350 8.13 8.89
B 0.240 0.260 6.10 6.60
L C 0.115 0.200 2.93 5.08
F 4 PL N D 0.016 0.020 0.41 0.50
E 0.040 0.070 1.02 1.77
F 0.010 0.014 0.25 0.36
C G 0.100 BSC 2.54 BSC
J 0.008 0.012 0.21 0.30
–T– K 0.100 0.150 2.54 3.81
SEATING L 0.400 0.425 10.16 10.80
PLANE G N 0.015 0.040 0.38 1.02
K J
D 6 PL
E 6 PL 0.13 (0.005) M T A M B M