Professional Documents
Culture Documents
8-Port Antenna Frequency Range Dual Polarization HPBW Adjust. Electr. DT
8-Port Antenna Frequency Range Dual Polarization HPBW Adjust. Electr. DT
Kathrein USA Greenway Plaza II, 2400 Lakeside Blvd., Suite 650, Richardson TX 75082
Phone: 214.238.8800 Fax: 214.238.8801 Email: info@kathrein.com
8-Port Antenna
Highbands B1 B2
1710 – 2180 1710 – 2180
Frequency Range MHz 1710 – 1880 1850 – 1990 1920 – 2180 1710 – 1880 1850 – 1990 1920 – 2180
Gain at mid Tilt dBi 18.4 18.5 18.4 18.4 18.6 18.6
Gain over all Tilts dBi 18.3 ± 0.3 18.4 ± 0.4 18.2 ± 0.5 18.3 ± 0.4 18.5 ± 0.5 18.4 ± 0.5
Horizontal Pattern:
Azimuth Beamwidth ° 60 ± 2.4 57 ± 2.5 59 ± 3.4 60 ± 2.9 57 ± 2.1 58 ± 3.2
Front-to-Back Ratio, dB
> 26 > 25 > 24 > 25 > 26 > 26
Total Power, ± 30°
Cross Polar Discrimination dB
> 28 > 28 > 24 > 28 > 27 > 24
at Boresight
Cross Polar Discrimination dB
> 16.0 > 15.5 > 10.0 > 15.0 > 14.5 > 9.5
over Sector
Azimuth Beam dB
< 0.5 < 1.0 < 1.5 < 0.5 < 1.0 < 1.5
Port-to-Port Tracking
Vertical Pattern:
Elevation Beamwidth ° 5.0 ± 0.3 4.7 ± 0.2 4.5 ± 0.4 5.0 ± 0.3 4.7 ± 0.2 4.5 ± 0.4
Electrical Downtilt °
0.0 – 6.0 0.0 – 6.0
continuously adjustable
Tilt Accuracy ° < 0.2 < 0.2 < 0.2 < 0.3 < 0.2 < 0.2
First Upper Side Lobe dB
> 14 > 14 > 14 > 14 > 15 > 15
Suppression
Cross Polar Isolation dB > 30 > 30
Port to Port Isolation dB > 30 (R1 // R2 // B1 // B2) > 30 (R1 // R2 // B1 // B2)
Max. Effective Power W 250 (at 50 °C ambient temperature) 250 (at 50 °C ambient temperature)
per Port
Values based on NGMN-P-BASTA (version 9.6) requirements.
85010002 1 clamp Mast diameter: 110 – 220 | 4.3 – 8.7 2.7 | 6.0 2
85010003 1 clamp Mast diameter: 210 – 380 | 8.3 – 15.0 4.8 | 10.6 2
85010008 1 downtilt kit Downtilt angle: 0° – 9° 4.3 | 9.5 1
Accessories (included in the scope of supply)
738546 1 clamp Mast diameter: 42 – 115 | 1.7 – 4.5 1.1 | 2.4 2
936.4887/b ngmn 04.19.02.00 Subject to alteration.
For downtilt mounting use the clamps for an appropriate mast diameter together with the downtilt kit.
2399 | 94.4
2432 | 95.7
2472 | 97.3
Wall mounting with two half clamps 738546 (included in the scope of supply).
Grounding: The metal parts of the antenna including the mounting and the inner
conductors are DC grounded.
Adjustment mechanism
with integrated scale
Kathrein USA Greenway Plaza II, 2400 Lakeside Blvd., Suite 650, Richardson TX 75082
Phone: 214.238.8800 Fax: 214.238.8801 Email: info@kathrein.com
8-Port Antenna
Layout of interface:
0
T
0
Tilt
t
17
99 | 3.9
110 | 4.3
Tilt
133 | 5.2 *
4)
56 | 2.2
34 | 1.3
1) 2)
270 | 10.6 3)
1) 33.5 | 1.3
476 | 18.7 2) 35.5 | 1.4
3) 50 | 2.0
576 | 22.7 * 4) 45 | 1.8
Bottom view
* Dimensions refer to radome
All dimensions in mm | inches
Correlation Table
Frequency range Array Connector
936.4887/b ngmn 04.19.02.00 Subject to alteration.
B1 B2
R1 R2
Left Right
152 [5.98]
100 [3.94]
[0.79–0.98]
40 [1.57]
72 [2.83]
20–25
40 [1.57]
15
2–1
4 4.53]
5–
[1.6
M10 MA = 25 Nm
M8 MA = 20 Nm
35 [1.38]
64 [2.52]
125 [4.92]
20–25
[0.79–0.98]
Subject to alteration.
936.3920/c
Please note: Kathrein does not recommend to use counter nuts. All dimensions in mm and [inches]
The additional nuts supplied are only meant as spares.
Kathrein USA Greenway Plaza II, 2400 Lakeside Blvd., Suite 650, Richardson TX 75082
Phone: 214.238.8800 Fax: 214.238.8801 Email: info@kathrein.com
General Instructions
for Adjustment Mechanism
1
2
2
➀ Twist protection. ➀ Thread for fixing the protective To set the downtilt angle exactly,
➁ Downtilt spindle with integrated cap or the RCU (Remote Control you must look horizontally at the
scale. Unit). scale. The lower edge of the gear-
➁ Gearwheel for RCU power drive. wheel must be used for alignment.
0° – max.°
0° – max.°
Remove the protective cap and the Set downtilt angle by rotating the Screw on the twist protection and
twist protection completely. gearwheel. the protective cap again.
For a description of RCU installation please refer to the respective data sheet.
Page 1 of 2
Kathrein USA Greenway Plaza II, 2400 Lakeside Blvd., Suite 650, Richardson TX 75082
Phone: 214.238.8800 Fax: 214.238.8801 Email: info@kathrein.com
General Instructions
for Feederline and RCU Installation
for Antennas
Please note: In order not to damage the interfaces, please make sure that only the right tools are used.
Tighten the feederline connector interfaces solely by using a common torque-wrench with a suitable wrench
width.
Adjustment mechanism
(protective cap removed) Ventilation hole
Colour coding:
Correlation of each RF input to:
– the corresponding adjustment mechanism
7-16 female (long neck) – the frequency range
– the polarization
32 | 1.3
Subject to alteration.
guidelines).
| 1.
1
These tools are suitable for 7-16 connectors with a wrench size of
27 or 32 mm | 1.1 or 1.3 inches, and the RCU attachment nut with a
wrench size of 41 mm | 1.6 inches.
Tighten nuts within a torque range of 25 – 33 Nm depending on
connector manufacturers’ specifications, respectively the RCU nut
with a torque range of 15 – 18 Nm.