Professional Documents
Culture Documents
Parker PV Series
Parker PV Series
Series PV
Variable Displacement
Catalogue HY11-3243/UK
August 2002
Catalogue HY11-3243/UK Axial piston pump
Series PV
Note
This document and other information from Parker Hannifin
GmbH, its subsidiaries, sales offices and authorized
distributors provide product or system options for further
investigation by users having technical expertise. Before you
select or use any product or system it is important that you
analyse all aspects of your application and review the
information concerning the product or system in the current
product catalogue. Due to the variety of operating conditions
and applications for these products or systems, the user,
through his own analysis and testing, is solely responsible
for making the final selection of the products and systems
and assuring that all performance and safety requirements
of the application are met. The products are subject to
change by Parker Hannifin GmbH at any time without notice.
PI PVplus UK.PM6.5 RH
Description Page
Introduction 4
Characteristics 5
Ordering code 6
Noise levels 8
Noise reduction measures 9
Efficiency and case drain flows 10
Dimensions 14
Pump combinations
Dimensions 26
Thru drive, shaft load limitations 28
Compensators
Dimensions / Seal kit compensators 29
Pressure compensators 30
Load-sensing compensators 31
Horse power compensators 32
Electrohydraulic p/Q control 34
Hydraulic circuit, ordering examples PVAP** 36
Hydraulic circuit, ordering examples PVAC** 38
Accessories 40
General installation information 41
PI PVplus UK.PM6.5 RH
Pump with standard pressure compensator code F*S Pump with load-sensing compensator code FFC
Ø0,8
Q PF Q
L P1 A L P1 A
PM P L P1 A PM P L P1 A
p p
S L = included S L = included
Technical Features
• Mounting interface according to VDMA-standards
sheet 24560 part 1
With thru drive for single and multiple pumps
• Standard: 4-hole flange ISO 3019/2 (metric). Op-
Swash plate type for open circuit tional: 4-hole flange ISO 3019/1 (SAE)
• Large servo piston with strong bias spring achieves
fast response; e.g. for PV046
upstroke < 70 ms ; downstroke < 40 ms
Note: follow installation instructions!
• Reduced pressure peaks due to active decompres-
sion of system at downstroke
• Also at low system pressure reliable compensator
operation. Lowest compensating pressure <10 bar
• Nine piston and new precompression technology
(precompression filter volume) result in unbeaten low
outlet flow pulsation
• Rigid and FEM-optimized body design for lowest
noise level
• Complete compensator program
• Thru drive for 100% nominal torque
• Pump combinations (multiple pumps) of same size
and model and mounting interface for basically all
metric or SAE mounting interfaces
Pump with horse power compensator code *LB Pump with electrohydr. displacement control code *PV
PP
UQ Q
L P1 A L P1 A
PM P L P1 A PL Q PM P L P1 A
U
s UQ
p
S L = included S L = included
PI PVplus UK.PM6.5 RH
Technical data
1)
peak pressure only
2)
peak pressure only, special version up to 20bar available
Pump combinations
See pages 26–27 Combination PV/PV Combination PV/gear pump
Selection table
1)
Model Max. displacement Output flow Input horse power in kW Max speed Weight
in cm3/rev in l/min at 1500 min-1 at 1500 min-1 and 350 bar in min-1 in kg
PV016 16 24 15.5
PV020 20 30 19.5 3000 19
PV023 23 34.5 22.5
PV032 32 48 31
PV040 40 60 39 2800 30
PV046 46 69 45
PV063 63 94.5 61.5 2800
PV080 80 120 78 2500 60
PV092 92 138 89.5 2300
PV140 140 210 136 2400 90
PV180 180 270 175 2200 90
PV270 270 405 263 1800 172
1)
The maximum speed ratings are shown for an inlet pressure of 1 bar (absolute) and for a fluid viscosity of ν = 30 mm²/s.
PI PVplus UK.PM6.5 RH
PV
pump compensator
Axial piston Size Variation Threads 2nd Compensator Design
pump and pump series:
variable displacement not required
displacement for order
high
pressure Rotation Mounting
version code Thru drive Seals
see opposite page
Code Variation
Code Thru drive option
1 standard no adaptor for 2nd pump
9 reduced displace- single pump
T prepared for thru drive
ment adjusted 2)
2)
for order specify displace- with adaptor for 2nd pump
ment Y8) SAE AA, Ø 50.8mm
A SAE A, Ø 82.55mm
Code Mounting interface Shaft B SAE B, Ø 101.6mm
D 4-hole flange cylindric, key C9) SAE C, Ø 127mm
SAE D10) SAE D, Ø 152.4mm
E 4-hole flange splined, SAE
ISO E11) SAE E, Ø 165.1mm
F3) 3019/1 4-hole flange cylindric, key
G12) metric, Ø 63mm
G3) 4-hole flange splined, SAE
H metric, Ø 80mm
K metr. ISO 4-hole flange cylindric, key
J metric, Ø 100mm
L 3019/2 4-hole flange splined, DIN 5480
K9) metric, Ø 125mm
3)
codes F and G only for PV140/180, see dimension sheet L10) metric, Ø 160mm
M11) metric, Ø 200mm
Code Port 4) Threads5) 8)
only for PV016 - PV023
9)
1 BSPP metric only for PV032 and larger
10)
3 UNF UNC only for PV063 and larger
11)
only for PV270
46) BSPP metr. M14 12)
only for PV016 - PV092
7 ISO 6149 UNC
8 ISO 6149 metric1)
4)
drain, gauge and flushing ports
5)
all mounting and connecting threads
6)
for PV063-PV180 only: pressure port 1 1/4" with 4 x M14 instead of 4 x M12
PI PVplus UK.PM6.5 RH
PV
Compensator Pump Compensator
Design
series:
not required
for order
at full flow
at full flow
60 70
at deadhead
at deadhead
50 60
0 100 200 300 0 100 200 300
Pressure [bar] Pressure [bar]
at full flow
at full flow
60 70
at deadhead
at deadhead
50 60
0 100 200 300 0 100 200 300
Pressure [bar] Pressure [bar]
at full flow
at full flow 80
70
at deadhead
at deadhead
70
60
52 60
0 100 200 300 0 100 200 300
Pressure [bar] Pressure [bar]
Typical sound level for single pumps, measured in unechoic chamber All data measured with mineral oil viscosity 30 mm²/s (cSt) at 50°C.
according to DIN 45 635, part 1 and 26. Microphone distance 1m;
speed: n = 1500 min-1.
PI PVplus UK.PM6.5 RH
series 40
on inlet, outlet and drain port of the pump.
• Exclusive use of gas tight tube fittings for inlet
connections to avoid ingression of air causing cavitation 200
and excessive noise. [bar] 220
PV180R1K1T1NFWS-series 20 [bar]
Secondary pump noise is caused by vibration induced 180
into all connected hydraulic components by the flow and 200
pressure pulsation of the pump. This secondary noise
adds typical 7 - 10 dBA to the noise of a pump measured 160 PV180R1K1T1NFWS-series 40
in the sound chamber according to DIN 45 635 (see 180
9.0 9.5 10.0 10.5 11.0 [s] 11.5
diagrams on opposite side). Therefore pipework, its
mounting and the mounting of all hydraulic components Figure 2: Comparison of the pressure pulsation in a
like pressure filters and control elements has a major system with 6 old PV pumps versus the same system
influence to the overall system noise level. with 6 PVplus pumps. The pulsation reduction effect of
Pulsation reduction with precompression volume: the precompression volume is evident.
The PV is equipped with a new technology for flow ripple
reduction. This method reduces the pulsation at the pump
outlet by 40 - 60 %. That leads to a significant reduction
of the overall system noise without additional cost and
without additional components (silencers etc.). The typical Other measures
reduction reaches 2 - 4 dBA. That means: with a pump Small diameter tubes do not only cause high flow speeds,
of the PV series the secondary noise adds only some 5 turbulences inside the tubes and cavitation in the pump,
- 7 dBA to the pump noise instead of the usually found 7 they also produce noise.
- 10 dBA. Only correctly sized connections of the largest possible
Figure 2 compares the measured pulsation of a system diameter according to the port size of the pump should be
with 6 pumps of 180 cm³/rev each. used.
PI PVplus UK.PM6.5 RH
Efficiency, power consumption Efficiency and case drain flows PV016, PV020, PV023
PV016 The efficiency and power graphs are measured at an
20 input speed of n = 1500 min-1, a temperature of 50°C and
25 100
Output flow [l/min]
30
Input power [kW]
Output flow [l/min]
output flow, vo
l. efficiency
Case drain flows PV016-023
overall efficiency
24 20 80 3
Case drain flow [l/min]
18 15 60
at deadhead
w
flo
full 2
t
12 10 e ra 40
ow
utp
inp
6 5 20
1
d
ea dhea
inpu t power at d
0 0 0
0 100 200 300
Pressure [bar] at full flow
PV023
100 0
Efficiency [%] (overall, volumetric)
40 25 vo
Input power [kW]
Output flow [l/min]
24 15 w 60
lo
lf
ful
at
wer
16 10 po 40
put
in
8 5 20
ea dhead
inpu t power at d
0 0 0
0 100 200 300
Pressure [bar]
PI PVplus UK.PM6.5 RH
Efficiency, power consumption Efficiency and case drain flows PV032, PV040, PV046
PV032 The efficiency and power graphs are measured at an
input speed of n = 1500 min-1, a temperature of 50°C and
40 out 100
Input power [kW]
Output flow [l/min]
60
put flow, vol. efficiency
Case drain flows PV032-046
overall efficiency
48 32 80 7.5
Case drain flow [l/min]
36 24 60
low
f ull f
a t 5.0
r
24 16 we 40
po at deadhead
ut
inp
12 8 20
2.5
eadhead
input power at d
0 0 0
0 100 200 300
Pressure [bar]
at full flow
PV046
50 0
Input power [kW]
80
Output flow [l/min]
100
vol. efficiency 0 100 200 300
overall efficiency Pressure [bar]
64 40 output flow 80
48 30 60
low
u ll f
a tf
r
we
32 20 t po 40
pu
in
16 10 20
head
input power at dead
0 0 0
0 100 200 300
Pressure [bar]
PI PVplus UK.PM6.5 RH
Efficiency, power consumption Efficiency and case drain flows PV063, PV080, PV092
PV063 The efficiency and power graphs are measured at an
100 input speed of n = 1500 min-1, a temperature of 50°C and
vol. efficiency
output flow
a fluid viscosity of 30 mm2/s.
overall efficiency Case drain flow and compensator control flow leave via
80 56 80 the drain port of the pump. To the values shown are to be
added 1 to 1.2 l/min , if at pilot operated compensators
(codes FR*, FF*, FT*, horse power compensator and p-
60 42 w 60
lo Q-control) the control flow of the pressure pilot valve also
ll f
t fu goes through the pump.
e ra
40 28 p ow 40 Please note: The values shown below are only valid for
t
pu static operation. Under dynamic conditions and at rapid
in
compensation of the pump the volume displaced by the
20 14 20 servo piston also leaves the case drain port. This dy-
d
a dh ea namic control flow can reach up to 80 l/min! Therefore the
er at de
inp ut p o w case drain line is to lead to the reservoir at full size and
0 0 0
0 100 200 300 without restrictions as short and direct as possible.
Pressure [bar]
PV080
100
Efficiency [%] (overall, volumetric)
120 80
Input power [kW]
Output flow [l/min]
w
48 f lo
72 ll 60
t fu
ra
owe 6
48 32 tp 40
npu at deadhead
i
24 16 20
h ead 3
r at dea d
input powe
0 0 0
0 100 200 300
Pressure [bar] at full flow
PV092
0
Efficiency [%] (overall, volumetric)
90 60 w 60
lo
lf
ful
at
wer
60 40 po 40
put
in
30 20 20
d
dea dh ea
inpu t power at
0 0 0
0 100 200 300
Pressure [bar]
PI PVplus UK.PM6.5 RH
Efficiency, power consumption Efficiency and case drain flows PV140, PV180, PV270
PV140 The efficiency and power graphs are measured at an
100 input speed of n = 1500 min-1, a temperature of 50°C and
vol. efficiency
a fluid viscosity of 30 mm2/s.
overall efficiency
Case drain flow and compensator control flow leave via
200 120 output flow 80
the drain port of the pump. To the values shown are to be
added 1 to 1.2 l/min , if at pilot operated compensators
90 w
(codes FR*, FF*, FT*, horse power compensator and p-
150 lo 60
ull f Q-control) the control flow of the pressure pilot valve also
t f
ra goes through the pump.
e
100 60 ow 40 Please note: The values shown below are only valid for
tp
pu static operation. Under dynamic conditions and at rapid
in
compensation of the pump the volume displaced by the
50 30 20 servo piston also leaves the case drain port. This dy-
a d he a d
namic control flow can reach up to 120 l/min! Therefore
i np ut power at de the case drain line is to lead to the reservoir at full size and
0 0 0
0 100 200 300 without restrictions as short and direct as possible.
Pressure [bar]
PV180 Case drain flows PV140-180
100 15
Efficiency [%] (overall, volumetric)
vol. efficiency
output flow
240 140 80
iency
10
ffic
w
lo
ll f
overall e
180 105 60
fu at deadhead
at
wer
t po
120 70 pu 40
in 5
60 35 20
at full flow
ad he ad
in pu t power at de
0 0 0 0
0 100 200 300 0 100 200 300
Pressure [bar] Pressure [bar]
PV270 Case drain flows PV270
18
Efficiency [%] (overall, volumetric)
vol. efficiency
ll efficie ncy
overa
output flow
400 200 80
w
12
lo
lf
ul
300 150 60
f
at deadhead
r at
we
tpo
pu
200 100 40
in
100 50 20
at full flow
dhea d
input powe r at dea
0 0 0 0
0 100 200 300 0 100 200 300
Pressure [bar] Pressure [bar]
PI PVplus UK.PM6.5 RH
94
16.5 120
Ø 25k6
Ø 100h8
16.5
80
13
drain port L1, 9
dimensions see L2 32
52 max. 133
132
197.5 View X
9
max. 212 10
Shown with standard pressure compensator
gage port M; G1/4
optional M 12 x 1.5; ISO 6149-1
(threads options 7 and 8)
oder 7/16 - 20 UNF
(threads option 3)
89
12
55 28-0.25
48
thread M10 - 22 deep 125
15
key 8 x 7 x 40
X DIN 6885
127 22
162 flushing port L3; G 3/8
170.5 optional M 18 x 1.5; ISO 6149-1
(threads options 7 and 8)
Inlet: oder 3/4 - 16 UNF
flange according ISO 6162 (threads option 3)
DN 32; PN 250 bar
58.7 The pump shown above has mounting option K
1 1/4”
32 and thru drive option T (prepared for thru drive).
4 x M10, 18 deep
30.2 optional 7/16 - 14 UNC - 2B
(threads options 3 and 7) Ø 100h8
50.8 19
Outlet: 43
flange according ISO 6162
DN 19; PN 400 bar
3/4”
Shown is a clockwise rotating pump. Counter clockwise rotating pumps have inlet, outlet and gauge ports reversed.
PI PVplus UK.PM6.5 RH
13.5
Ø 25.4-0.05
28.17±0.13
Ø 101.6-0.05 89.8
thread
3/8-16 UNC-2B 44.9
22 deep
9.4 key
8 6.35 x 6.35
44.9
42 40 long
89.8
50
Shown above is mounting option D
Ø 101.6-0.05
mounting option E
splined shaft 15T 16/32 DP, flat root, side fit
ANSI B92.1
46
A
G C
B H
197.5 D
F
225
47.5
Thru shaft adaptors are available with the following dimensions: Dimension H and available couplings see page 24.
At threads options 3 and 7 the dimensions E and G are UNC - 2B
A B C D E F G threads.
63 10 85 - M8 100 M8
80 10 103 - M8 109 M10
100 10.5 125 - M10 - -
50.8 10 - - - 82 M8
82.55 10 - - - 106 M10
101.6 10.5 - 89.8 M12 - -
PI PVplus UK.PM6.5 RH
107
22
Ø 32k6
Ø 125h8
150
92
22
98
14
66 35-0.25 160
60
Thread M10 - 22 deep
17
Key 10 x 8 x 56
X DIN 6885
146 28
25
57.2
Outlet:
flange according ISO 6162
47
DN 25; PN 400 bar
Shown is a clockwise rotating pump. Counter clockwise rotating pumps have inlet, outlet and gauge ports reversed.
PI PVplus UK.PM6.5 RH
14
Ø 31.75 -0.05
35.2 ±0.13
114.5
Ø 127-0.05
thread
3/8-16 UNC-2B 57.25
22 deep
12.7 key
8 7.94 x 7.94
56 long 57.25
shown above is mounting option D 60 114.5
68
Ø 127-0.05
mounting option E
splined shaft 14T 12/24 DP, flat root, side fit
ANSI B92.1
56
A
C
G
H
227 B D
L F
K
Thru shaft adaptors are available with the following dimensions: Dimension H and available couplings see page 24.
At threads options 3 and 7 the dimensions E and G are UNC - 2B
A B C D E F G K L threads.
63 8.5 85 - M8 100 M8 49 261
80 8.5 103 - M8 109 M10 49 261
100 10.5 125 - M10 140 M12 49 261
125 12 160 - M12 - - 49 261
82.55 8 - - - 106 M10 49 261
101.6 11 - 89.8 M12 146 M12 49 261
127 13.5 - 114.5 M12 - - 64 276
PI PVplus UK.PM6.5 RH
196
Ø 40 k6 Ø 160 h8
31
31
120
18
121
78 200
86 238 43-0.25
thread
M12 - 28 deep
26
key 12 x 8 x 80
DIN 6885
4 x M12, 20 deep
optional 1/2 - 13 UNC - 2B
42.9 (threads options 3 and 7) Ø 160 h8
31.8
4 x M12, 20 deep
optional 1/2 - 13 UNC - 2B mounting option L
(threads options 3 and 7) splined shaft W 40 x 1.5 x 25 x 8f DIN 5480
or threads option 4
(M14, 20 deep)
66.6
32
Outlet:
flange according ISO 6162
DN 32; PN 400 bar 56
Shown is a clockwise rotating pump. Counter clockwise rotating pumps have inlet, outlet and gauge ports reversed.
PI PVplus UK.PM6.5 RH
key 11.11x11.11
80 long
20.6
Ø 44.45 -0.05
49.3 ±0.13
161.6
Ø 152.4-0.05
80.8
thread
12.7 1/2-13 UNC-2B
8 28 deep
82 80.8
shown above is mounting option D 161.6
90
Ø 152.4 -0.05
mounting option E
splined shaft 13T 8/16 DP, flat root, side fit
ANSI B92.1
75
A C
H
287 B
L D
K F
Thru shaft adaptors are available with the following dimensions: Dimension H and available couplings see page 24.
At threads options 3 and 7 the dimensions E and G are UNC - 2B
A B C D E F G K L
threads.
63 10 85 - M8 100 M8 58 326
80 10 103 - M8 109 M10 58 326
100 12 125 - M10 140 M12 58 326
125 12 160 - M12 180 M16 58 326
160 12 200 - M16 - - 58 326
82.55 10 - - - 106 M10 58 326
101.6 12 - 89.8 M12 146 M12 58 326
127 14 - 114.5 M12 181 M16 58 326
152.4 14 - 161.6 M16 - - 78 346
PI PVplus UK.PM6.5 RH
158
Ø 50k6
Ø 160h8
35
35 200
145
drain port L1 20
dimensions see L2 48
350 9
max. 133
max. 385 92
200
9
gage port M; G1/4 10 View X
optional M 12 x 1.5; ISO 6149-1 Shown with standard pressure compensator
(threads options 7 and 8)
oder 7/16 - 20 UNF
(threads option 3)
147
283
18
106
53.5-0.25
105 200
Thread M16 - 36 deep
Key 14 x 9 x 75
DIN 6885
X
233 40
pressure port: 295 flushing port L3; G 3/4
suction port: 305 optional M 27 x 2; ISO 6149-1
Inlet: (threads options 7 and 8)
flange according ISO 6162 oder 1 1/16 - 12 UNF
DN 64; PN 160 bar (threads option 3)
88.9 The pump shown above has mounting option K
64 and thru drive option T (prepared for thru drive).
4 x M12, 20 deep
optional 1/2 - 13 UNC - 2B
(threads options 3 and 7)
50.8
4 x M12, 20 deep Ø 160h8
31.8 optional 1/2 - 13 UNC - 2B
mounting option L
(threads options 3 and 7)
splined shaft W 50 x 2 x 24 x 9g DIN 5480
or threads option 4
(M14, 22 deep)
66.6 32
Outlet:
flange according ISO 6162 78
DN 32; PN 400 bar
Shown is a clockwise rotating pump. Counter clockwise rotating pumps have inlet, outlet and gauge ports reversed.
PI PVplus UK.PM6.5 RH
21
Ø 50.8-0.05
56.4±0.13 80.8
Ø 152.4-0.05
161.6
thread
5/8-11UNC-2B
12.7 25 deep
8
key 12.7 x 12.7
91.4
shown above is mounting option D 75 long 80.8
99.4
161.6
mounting option F
Ø 44.45-0.05 key
Ø 152.4-0.05 49.3±0.13 11.11 x 11.11 Ø 152.4-0.05
mounting option E 55 long mounting option G
splined shaft 15T 8/16 DP, Ø 152.4-0.05 splined shaft 13T 8/16 DP,
flat root, side fit flat root, side fit
ANSI B92.1 thread ANSI B92.1
1/2-13UNC-2B
25 deep
88 75 75
A C
G
B H
350 D
415 F
97
Thru shaft adaptors are available with the following dimensions: Dimension H and available couplings see page 24.
At threads options 3 and 7 the dimensions E and G are UNC - 2B
A B C D E F G threads.
80 10 103 - M8 109 M10
100 12 125 - M10 140 M12
125 12 160 - M12 180 M16
160 12 200 - M16 - -
82.55 10 - - - 106 M10
101.6 12 - 89.8 M12 146 M12
127 14 - 114.5 M12 181 M16
152.4 14 - 161.6 M16 - -
PI PVplus UK.PM6.5 RH
184
Ø 65 k6 Ø 200h8
45
45
176
172
22
128
69 -0.25
110
thread 250
M20 - 42 deep
key 18 x 11 x 98
DIN 6885
306 50
378
403 flushing port L3; G 3/4
optional M 27 x 2; ISO 6149-1
(threads options 7 and 8)
Inlet: or 1 1/16 - 12 UNF
flange according ISO 6162 (threads option 3)
DN 89; PN 25 bar
120.7 The pump shown above has mounting option K
and thru drive variation T (prepared for thru drive).
Ø 88
4 x M16, 32 deepf
optional 5/8 - 11 UNC - 2B
69.8 (threads options 3 and 7)
Ø 200h8
36.5
mounting option L
4 x M16, 32 deep splined shaft W 60 x 2 x 28 x 9g DIN 5480
optional 5/8 - 11 UNC - 2B
threads options 3 and 7)
79.4 Ø 38
Outlet: 80
flange according ISO 6162
DN 38; PN 400 bar
Shown is a clockwise rotating pump. Counter clockwise rotating pumps have inlet, outlet and gauge ports reversed.
PI PVplus UK.PM6.5 RH
key
12.7 x 12.7
20.6
75 long
Ø 50.8 -0.05
56.4 ±0.13
224.5
Ø 165.1 -0.05
112.25
thread
15.9 5/8-11UNC-2B
8 25 deep
89.5 112.25
97.5 224.5
shown above is mounting option D
Ø 165.1 -0.05
mounting option E
splined shaft 15T-8/16 DP, flat root, side fit
ANSI B92.1
88
A C
472.5 D
531.5 F
97
MK PV BG
Mounting Axial Size Second Thread Seals Design
kit piston pump series
pump (see name
plate)
series PV
MK PV BG
Mounting Axial Size Coupling Design
kit piston series
pump (see name
plate)
series PV
PI PVplus UK.PM6.5 RH
Seal kits
SK PV BG
Seal kit Axial Size Seals Thread, Design
piston port series
pump (see name
plate)
series
PV
Code Pump size Code Thread Port
1 Pump size 1: PV016 - PV023 1 metric BSPP
2 Pump size 2: PV032 - PV046 3 UNC UNF
Code Seals 7 UNC ISO 6149
3 Pump size 3: PV063 - PV092
N NBR 8 metric ISO 6149
4 Pump size 4: PV140 - PV180 V FPM
5 Pump size 5: PV270 E EPR
RK PV BG
Spare Axial Size Contents partly Design
parts kit piston optional:Thread series
pump or rotation or (see name
plate)
series seals
PV
Code Pump Size Code Thread
1 Pump size 1: PV016 - PV023 M metric
2 Pump size 2: PV032 - PV046 Code Contents Optional S SAE / UNC
3 Pump size 3: PV063 - PV092 VT Connecting parts, kit Thread Rotation
4 Pump size 4: PV140 - PV180 WP Shaft with key Thread R clockwise
5 Pump size 5: PV270 WZ Splined shaft Thread L counter-clockw.
SS Valve plate Rotation
Seals
SB Bushing for servo piston Seals
N NBR
Contents - fixed
V FPM
GLE Trunnion bearing kit E EPR
ROG Rotating unit incl. piston set
KOS Piston set
SRS Swash plate
WQS Shaft with key, reinforced, only for size 4, only with SAE
WFS Splined shaft, reinforced, only for size 4, only with SAE
RFE Bias spring kit
SKS Servo piston kit
RK PV
Spare Axial Displace- Contents Seals Design
parts kit piston ment series
pump (see name
plate)
series PV
Code Displacement Code Seals
016 PV016 063 PV063 N NBR
020 PV020 080 PV080 V FPM
023 PV023 092 PV092 E EPR
032 PV032 140 PV140 Code Contents
040 PV040 180 PV180 For parts included, see spare parts list PVI-BGx-GB-yy; available upon request.
HE Displacement limiter
x stands for frame size 1 - 5
046 PV046 270 PV270 adjustable yy stands for design series
PI PVplus UK.PM6.5 RH
M K B
D C
PI PVplus UK.PM6.5 RH
Combinations PV/PGP
M K B
D C
For technical information see gearpump /-motor catalogue (on request: HY11-3252/UK)
PI PVplus UK.PM6.5 RH
Important notice
The max. allowable torque of the individual shaft must
not be exceeded. For 2-pump combinations there is no
problem because PV series offers 100% thru torque. For
3-pump combinations (and more) the limit torque could
be reached or exceeded.
Therefore it is necessary to calculate the torque factor
and compare it with the allowed torque limit factor in the
table.
PI PVplus UK.PM6.5 RH
Remote pressure compensator, code FRC Remote pressure comp. with interface NG6, code FR1
Load sensing compensator, code FFC Load sensing comp. with interface NG6, code FF1
2 x M5 - 10 deep optional 10-32 UNC
All control ports G1/4 optional M 12 x 1.5; ISO 6149-1
(threads option 3 and 7)
(threads options 7 and 8) or 7/16-20 UNF (threads option 3)
31.5 Interface NG6, CETOP 03
T
31 32,5
42.5 P
74.5 2 x M5 - 10deep in
pump body (see note above)
pressure pilot port PP (code FRC)
load-sensing-port PF (code FFC) load-sensing-port PF (code FF1)
(plugged for code FR1 )
40
24
2-valve compensator, code FT1 Proportional p-Q-compensator, code FPR (for code
FPV lower valve only without interface)
interface NG6, CETOP 03
interface NG6, CETOP 03
T
80 40
40
49
50
load sensing port PF
LVDT for proportional compensator Pilot valve for horse power compensator
round connector
M 12 x 1
5 pins
69 34
pump body
pump body
SK PVC
Seal kit Compensator Seal
for axial
piston pump
series PV Code Seal Seal kit includes all seals for all single compensator options and the
seals for LVDT and horse power pilot valve. For 2-valve-compensators
N NBR two seal kits are to be ordered.
V FPM Spare parts lists and ordering codes for replacement compensator
E EPR valves see manual PVI-PVC-GB; available upon request
PI PVplus UK.PM6.5 RH
PI PVplus UK.PM6.5 RH
Ø0.8
T P
T P
PF PF Q
L P1 A L P1 A
PM P L P1 A PM P L P1 A
Load-sensing Load-sensing
compensator compensator with
code FFC interface NG6 for p
external orifice and accessories
pressure pilot valve code FF1
S L S L = included
PI PVplus UK.PM6.5 RH
Hydraulic-mechanical horse power compensator Ordering code for the horse power option
The hydraulic-mechanical horse power compensator The first digit designates the horse power setting:
consists of a modified remote pressure compensator Code B = 3.0 kW etc. up to
(Code *L*) or of a modified load-sensing compensator Code 3 = 132.0 kW
(Code *C*) and a pilot valve. This pilot valve is integrated
The second digit designates the pilot flow source:
into the pump and is adjusted by a cam sleeve. The cam
sleeve has a contour that is designed and machined for Code L internal pilot pressure, remote pressure func-
the individual displacement and the nominal horse power tion.
setting. Code C external pilot pressure, combines horse power
At a large displacement the opening pressure (given by compensation with load-sensing compensa-
the cam sleeve diameter) is lower than at small displace- tion.
ments. This makes the pump compensate along a The third digit designates the possibility to adjust the
constant horse power (torque) curve (see diagrams on overriding pressure compensation:
opposite page). Code A comes with a top side NG6/D03 interface on
For all nominal powers of standard electrical motors the control valve to mount any suitable pilot
Parker offers a dedicated cam sleeve. The exchange of
valve or Parker pump accessories.
this cam sleeve (e. g.: to change horse power setting) can
easily be done without disassembly of the pump. Code B has a threaded pilot port Pp (G1/4) to connect
On top of that an adjustment of the horse power setting a remote pilot valve with piping.
can be done within certain limits by adjusting the preload Code C includes a pilot valve for manual pressure
of the pilot control cartridge spring . That allows an adjustment. Max. setting: 350 bar.
adjustment of a constant horse power setting for other Page 33 shows typical control characteristics and the
than the nominal speeds (1500 min-1) or for other horse available horse power settings for the different pump
powers. sizes and displacements.
T P
T P
T P
T P
PP
L P1 A
L P1 L P1 A PM P L P1 A PL
A
PM P L P1 A PL PM P L P1 A PL
Ø0,8
Note:
If version *CB
is required with an external pilot T P
valve and Ø0.8 mm orifice, the orifice T P
L P1 A
L P1 A PM P L P1 A PL
PM P L P1 A PL
PI PVplus UK.PM6.5 RH
PV023 200
PV020 PV140
30 PV016 180
140
20 120
100
15
80
10 60
40
5
20
0 0
0 50 100 150 200 250 300 350 0 50 100 150 200 250 300 350
pressure p [bar] pressure p [bar]
70 300
flow rate Q [l/min]
210
40 180
150
30
120
20 90
60
10
30
0 0
0 50 100 150 200 250 300 350 0 50 100 150 200 250 300 350
pressure p [bar] pressure p [bar]
140
flow rate Q [l/min]
flow rate Q [l/min]
80 250
60 200
150
40
100
20
50
0
0 50 100 150 bar 250 300 350 0
pressure p [bar] 0 50 100 150 200 250 300 350
pressure p [bar]
The diagrams shown are only valid for the following working conditions:
Speed : n = 1500 rev/min Fluid : HLP, ISO VG46
Temperature : t = 50°C Viscosity : ν = 46 mm2/s at 40°C
PI PVplus UK.PM6.5 RH
PQ 00
NOTE!
The electronic modules are not included in the pump More technical information on these modules can be found in
compensator. Please order separately. catalogue HY11-2500/UK, chapter 10, Electronics.
Repeatability ± 0.75 %
- nominal voltage 16 V
- environmental temperature 50 °C
- duty cycle 100 %
- protection class IP54 0 0
- connector ISO 4400 0 input command +10V 0 time t
TA TR
Inductive position feedback (LVDT): Response times
- supply voltage 18 to 36 VDC Size TA [ms] TR [ms]
- current requirement <50 mA
3.5 to 11.5 VDC PV023 50 50
- output voltage
- environmental temperature 0 to 50 °C PV046 70 70
- load to output signal > 5 kOhm (short circuit pro- PV092 90 90
tected) PV180 150 150
- connector round connector M12x1.5pin PV270 200 200
PI PVplus UK.PM6.5 RH
DB1
P
DP
signal. A1 DB2
If the system does not provide enough back pressure - espe- P1
cially at low displacement and low load - there are two options: UP UQ
the shuttle valve subplate and the preload valve option. T
L A1
If an external auxiliary pressure is available, the control
option WP* is equipped with a shuttle valve circuit according pintern
to the diagram left. At a low pump outlet pressure the pump p1
displacement adjustment circuit is supplied by the auxiliary PM P L P1 A
U
pressure and allows adjustment of the pump to zero flow at s
zero pressure. If the pump outlet pressure exceeds the auxil-
iary pressure, the shuttle valve shifts to internal pressure
supply.
Proportional displace-
Depending of the pump size and the response requirements ment control with pres-
an auxiliary power source of 20 - 30 bar and 20 - 40 l/min is sure compensation
and shuttle valve
recommended.
subplate
Note: pressure control is only available above the auxiliary S L code WPR
pressure level and operation of the pump at zero flow and zero
pressure requires extreme care to maintain lubrication of the
rotating group.
Inlet:
flange port
Outlet: ISO 6162, Proportional displace-
flange port flanged direct to ment control with pres-
ISO 6162 pump pressure sure compensation
port and preload valve
S L
PI PVplus UK.PM6.5 RH
PVAP DP1
Ordering Examples
Example 1 Example 2
PV pump with fast response remote pressure control, Same pump, accessories not fitted:
relief valve with 2 pressure stages, electrical pressure PV * * * * * * * * FR1; 1 = PVAC2PCMNSJP
selection, nitrile seals, spindle adjustment, 24 VDC sole- Example 3
noid, plug to DIN 46350 accessories fitted: Usable for horsepower control and proportional volume
PV * * * * * * * * FRZ; Z = PVAC2PCMNSJP control, too.
PI PVplus UK.PM6.5 RH
PV AC M 35
For Accessories Function Mounting Metric Seals Adjustment Solenoid Solenoid Nominal Design
PV Pump for Bolts 1)
Accessories pressure Series
Series Compensa- 350bar 2) not required
tors for order
Dimensions
PVAC1P* PVAC1E*
DC solenoid 205
AC solenoid 190
Adjustment
Code S
Adjustment
Code L
Pressure relief valve mounted on 2-valve pressure-flow compensator Pressure relief valve, electrical unloading, mounted on compensator
type T type R or F
PVAC2P* PVAC2E*/2M*
DC solenoid 205 DC solenoid 241
AC solenoid 190 AC solenoid 211
2-pressure relief valve, electrical selection, mounted on compensator 2-pressure relief valve, electrical selection and unloading, mounted on
type R or F compensator type R or F
PI PVplus UK.PM6.5 RH
Parker Fluid Connectors, Tube Fittings Division or Havit Hydraulik GmbH & Co.
Am Metallwerk 9 Münchner Str. 11
33659 Bielefeld, Germany 85123 Karlskron, Germany
Tel.: (+521) 4048-0, fax: (+521) 4048280 Tel.: (+8450) 7031/7032, fax: (+8450) 7033
PI PVplus UK.PM6.5 RH
PI PVplus UK.PM6.5 RH
PI PVplus UK.PM6.5 RH
PI PVplus UK.PM6.5 RH