Professional Documents
Culture Documents
Interior Lighting System: Section
Interior Lighting System: Section
E
CONTENTS
PRECAUTION ............................................... 3 BATTERY SAVER : CONSULT Function (BCM - F
BATTERY SAVER) ..................................................16
PRECAUTIONS ................................................... 3
Precaution for Supplemental Restraint System INTELLIGENT KEY ....................................................17
G
(SRS) "AIR BAG" and "SEAT BELT PRE-TEN- INTELLIGENT KEY : CONSULT Function (BCM -
SIONER" ................................................................... 3 INTELLIGENT KEY) (Type 1) ..................................17
Precautions for Removing Battery Terminal ............. 3 INTELLIGENT KEY : CONSULT Function (BCM -
INTELLIGENT KEY) (Type 2) ..................................21 H
SYSTEM DESCRIPTION .............................. 5
ECU DIAGNOSIS INFORMATION .............. 26
COMPONENT PARTS ........................................ 5 I
Component Parts Location ........................................ 5 BCM ................................................................... 26
List of ECU Reference .............................................26
SYSTEM .............................................................. 8
WIRING DIAGRAM ...................................... 27 J
INTERIOR ROOM LAMP CONTROL SYSTEM .......... 8
INTERIOR ROOM LAMP CONTROL SYSTEM : INTERIOR ROOM LAMP CONTROL SYSTEM
System Description ................................................... 8 ... 27
K
Wiring Diagram ........................................................27
INTERIOR ROOM LAMP BATTERY SAVER SYS-
TEM ............................................................................ 10 ILLUMINATION ................................................. 38
INTERIOR ROOM LAMP BATTERY SAVER Wiring Diagram ........................................................38 INL
SYSTEM : System Description ............................... 10
BASIC INSPECTION ................................... 52
ILLUMINATION CONTROL SYSTEM ....................... 12
ILLUMINATION CONTROL SYSTEM : System DIAGNOSIS AND REPAIR WORK FLOW ....... 52 M
Description .............................................................. 12 Work Flow ................................................................52
INL-1
LUGGAGE ROOM LAMP CIRCUIT .................. 60 Exploded View ........................................................ 71
Component Function Check ................................... 60 Replacement ........................................................... 71
Diagnosis Procedure .............................................. 60
GLOVE BOX LAMP ........................................... 72
SPICY ILLUMINATION CIRCUIT ...................... 62 Exploded View ........................................................ 72
Component Function Check ................................... 62 Replacement ........................................................... 72
Diagnosis Procedure .............................................. 62
SPICY ILLUMINATION ...................................... 73
PUSH-BUTTON IGNITION SWITCH ILLUMI- Exploded View ........................................................ 73
NATION CIRCUIT .............................................. 64 Replacement ........................................................... 74
Component Function Check ................................... 64
Diagnosis Procedure .............................................. 64
ROOM LAMP ..................................................... 75
Exploded View ........................................................ 75
SYMPTOM DIAGNOSIS ............................. 66 Removal and Installation ......................................... 75
Replacement ........................................................... 76
INTERIOR LIGHTING SYSTEM SYMPTOMS ... 66
Symptom Table ...................................................... 66 PERSONAL LAMP ............................................ 77
Exploded View ........................................................ 77
REMOVAL AND INSTALLATION ............... 68 Removal and Installation ......................................... 77
Replacement ........................................................... 78
MAP LAMP ........................................................ 68
Exploded View ........................................................ 68 LUGGAGE ROOM LAMP .................................. 79
Exploded View ........................................................ 79
MAP LAMP ................................................................ 68 Removal and Installation ......................................... 79
MAP LAMP : Removal and Installation ................... 68 Replacement ........................................................... 80
MAP LAMP : Replacement ..................................... 69
SERVICE DATA AND SPECIFICATIONS
MAP LAMP FINISHER .............................................. 69
MAP LAMP FINISHER : Removal and Installation... 69
(SDS) .......................................................... 81
INL-2
PRECAUTIONS
< PRECAUTION >
PRECAUTION A
PRECAUTIONS
Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT B
PRE-TENSIONER" INFOID:0000000010430899
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along C
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. Information necessary to service the system safely is included in the “SRS AIR BAG” and
“SEAT BELT” of this Service Manual.
WARNING: D
Always observe the following items for preventing accidental activation.
• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in
the event of a collision that would result in air bag inflation, all maintenance must be performed by E
an authorized NISSAN/INFINITI dealer.
• Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal
injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
F
Module, see “SRS AIR BAG”.
• Never use electrical test equipment on any circuit related to the SRS unless instructed to in this Ser-
vice Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or harness
connectors. G
PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS
WARNING: H
Always observe the following items for preventing accidental activation.
• When working near the Air Bag Diagnosis Sensor Unit or other Air Bag System sensors with the
ignition ON or engine running, never use air or electric power tools or strike near the sensor(s) with
a hammer. Heavy vibration could activate the sensor(s) and deploy the air bag(s), possibly causing I
serious injury.
• When using air or electric power tools or hammers, always switch the ignition OFF, disconnect the
battery, and wait at least 3 minutes before performing any service. J
Precautions for Removing Battery Terminal INFOID:0000000010503204
• With the adoption of Auto ACC function, ACC power is automatically supplied by operating the intelligent key K
or remote keyless entry or by opening/closing the driver side door. In addition, ACC power is supplied even
after the ignition switch is turned to the OFF position, i.e. ACC power is supplied for a certain fixed time.
• When disconnecting the 12V battery terminal, turn off the ACC
power before disconnecting the 12V battery terminal, observing INL
“How to disconnect 12V battery terminal” described below.
NOTE:
Some ECUs operate for a certain fixed time even after ignition M
switch is turned OFF and ignition power supply is stopped. If the
battery terminal is disconnected before ECU stops, accidental DTC
detection or ECU data damage may occur.
N
• For vehicles with the 2-batteries, be sure to connect the main bat-
tery and the sub battery before turning ON the ignition switch.
NOTE:
SEF289H
If the ignition switch is turned ON with any one of the terminals of O
main battery and sub battery disconnected, then DTC may be detected.
• After installing the 12V battery, always check "Self Diagnosis Result" of all ECUs and erase DTC.
NOTE: P
The removal of 12V battery may cause a DTC detection error.
HOW TO DISCONNECT 12V BATTERY TERMINAL
Disconnect 12V battery terminal according to Instruction 1 or Instruction 2 described below.
For vehicles parked by ignition switch OFF, refer to Instruction 2.
INSTRUCTION 1
1. Open the hood.
INL-3
PRECAUTIONS
< PRECAUTION >
2. Turn key switch to the OFF position with the driver side door opened.
3. Get out of the vehicle and close the driver side door.
4. Wait at least 3 minutes. For vehicle with the engine listed below, remove the battery terminal after a lapse
of the specified time.
INL-4
COMPONENT PARTS
< SYSTEM DESCRIPTION >
SYSTEM DESCRIPTION A
COMPONENT PARTS
Component Parts Location INFOID:0000000010335129
B
INL
JMLIA5169ZZ
N
No. Component Function
INL-5
COMPONENT PARTS
< SYSTEM DESCRIPTION >
No. Component Function
• Activates the interior room lamp timer depending on the vehicle condition to turn the inte-
rior room lamps ON/OFF.
• Operates the interior room lamp battery saver depending on the vehicle condition to turn
interior room lamps OFF.
BCM • Detects each switch condition by the combination switch reading function.
• Judges the illumination lamp ON/OFF status depending on the vehicle condition. And then
transmits request signal to IPDM E/R and combination meter (via CAN communication).
Refer to BCS-7, "BODY CONTROL SYSTEM : Component Parts Location" for detailed in-
stallation location.
Refer to DLK-29, "Component Parts Location" (Type 1), DLK-203,
Power window main switch "Component Parts Location" (Type 2), DLK-386, "Component Parts Location" (Type 3) or
(Door lock and unlock switch) DLK-511, "Component Parts Location" (Type 4).
Refer to DLK-24, "Information" for detailed vehicle information.
Front outside handle assembly Refer to DLK-29, "Component Parts Location" (Type 1), DLK-203,
4 "Component Parts Location" (Type 2).
(Request switch* ) Refer to DLK-24, "Information" for detailed vehicle information.
Refer to DLK-29, "Component Parts Location" (Type 1), DLK-203,
Front door lock assembly
"Component Parts Location" (Type 2), DLK-386, "Component Parts Location" (Type 3) or
(Driver side)
DLK-511, "Component Parts Location" (Type 4).
(Unlock sensor)
Refer to DLK-24, "Information" for detailed vehicle information.
Refer to DLK-29, "Component Parts Location" (Type 1), DLK-203,
"Component Parts Location" (Type 2), DLK-386, "Component Parts Location" (Type 3) or
Door switch
DLK-511, "Component Parts Location" (Type 4).
Refer to DLK-24, "Information" for detailed vehicle information.
Luggage room lamp Refer to INL-81, "bulb specifications".
Back door opener switch as- Refer to DLK-29, "Component Parts Location" (Type 1), DLK-203,
sembly "Component Parts Location" (Type 2).
(Request switch*4) Refer to DLK-24, "Information" for detailed vehicle information.
Refer to DLK-29, "Component Parts Location" (Type 1), DLK-203,
Back door lock assembly "Component Parts Location" (Type 2), DLK-386, "Component Parts Location" (Type 3) or
(Back door switch) DLK-511, "Component Parts Location" (Type 4).
Refer to DLK-24, "Information" for detailed vehicle information.
NAVI control unit*7 Controls the brightness of display according to the signal from BCM.
Push-button ignition switch
(Push-button ignition switch il- Refer to INL-81, "bulb specifications".
lumination)*4
• Interior room lamp relay is controlled by BCM.
Interior room lamp relay
• Interior room lamp relay supplies power to interior room lamp and light & rain sensor.
INL-6
COMPONENT PARTS
< SYSTEM DESCRIPTION >
*6: With spicy illumination
*7: With NAVI A
INL
INL-7
SYSTEM
< SYSTEM DESCRIPTION >
SYSTEM
INTERIOR ROOM LAMP CONTROL SYSTEM
INTERIOR ROOM LAMP CONTROL SYSTEM : System Description INFOID:0000000010335130
SYSTEM DIAGRAM
With Sunshade System
JMLIA5146GB
INL-8
SYSTEM
< SYSTEM DESCRIPTION >
Without Sunshade System
A
I
JMLIA5375GB
OUTLINE
• Following lamps are controlled by interior room lamp timer control function of BCM. J
- Map lamp*
- Room lamp*
- Personal lamp* K
• Luggage room lamp is controlled by luggage room lamp control function of BCM.
• Push-button ignition switch illumination is controlled by push-button ignition switch illumination control func-
tion of BCM.
*: Interior room lamp time control operates when the switch position is DOOR. INL
JPLIA0093GB
• Following lamps turn ON and OFF (gradual brightening and dimming) by the interior room lamp timer.
- Map lamp
INL-9
SYSTEM
< SYSTEM DESCRIPTION >
- Room lamp
- Personal lamp
• For Europe, Russia or South Africa: Timer operating time is 30 seconds.
• Except for Europe, Russia of South Africa: Timer operating time is 15 seconds.
• Brightening time is 1 second and dimming time is 1 seconds.
• BCM judges the vehicle condition with the following items and activates the interior room lamp timer.
- Ignition switch status
- Key switch signal
- Door switch signal
- Door lock/unlock signal (remote keyless entry receiver, door lock and unlock switch, each door request
switch)
NOTE:
Factory setting of interior room lamp is with interior room lamp timer control. This setting can be set to without
by using CONSULT. Refer to INL-15, "INT LAMP : CONSULT Function (BCM - INT LAMP)".
Interior Room Lamp ON Operation
• BCM always turns interior room lamp relay ON to turn on interior room lamp when any door opens.
• BCM activates the interior room lamp timer in any of the following condition to turn the interior room lamp ON
for a period of time.
- Status of all doors are OPEN → CLOSE
- Ignition switch is turned ON → OFF
- Key switch is ON → OFF
- Door unlock signal is detected when all doors close with ignition switch OFF
NOTE:
The timer restarts if new condition is input during the timer operating time.
Interior Room Lamp OFF Operation
BCM stops the timer in any of the following condition to turn the interior room lamp OFF.
• The timer operating time is expired
• Ignition switch is turned OFF → ON
• Door lock signal is detected with all doors close.
LUGGAGE ROOM LAMP CONTROL
BCM turns luggage room lamp ON when the following condition is detected.
• Back door switch is ON
BCM turns luggage room lamp OFF when the following condition is detected.
• Back door switch is OFF
PUSH-BUTTON IGNITION SWITCH ILLUMINATION CONTROL
Push-button Ignition Switch Illumination ON Operation
BCM turns the push-button ignition switch illumination ON when Ignition switch is ON.
Push-button Ignition Switch Illumination OFF Operation
BCM turns the push-button ignition switch illumination OFF when the following condition is satisfied.
• Status does not change for 16 seconds
• Driver side door is UNLOCK → LOCK
INTERIOR ROOM LAMP BATTERY SAVER SYSTEM
INTERIOR ROOM LAMP BATTERY SAVER SYSTEM : System Description
INFOID:0000000010335132
SYSTEM DIAGRAM
INL-10
SYSTEM
< SYSTEM DESCRIPTION >
With Sunshade System
A
I
JMLIA5148GB
INL
JMLIA5149GB
INL-11
SYSTEM
< SYSTEM DESCRIPTION >
OUTLINE
• Interior room lamp battery saver is controlled by BCM.
• BCM turns applicable lamps OFF depending on the vehicle condition. This function prevent battery dis-
charge if the driver neglects, turning OFF any lamps.
Applicable lamps
- Map lamp
- Room lamp
- Personal lamp
- Luggage room lamp
- Vanity mirror lamp
INTERIOR ROOM LAMP BATTERY SAVER FUNCTION
• BCM turns interior room lamp relay ON and keeps the interior room lamp power supply continuously when
the ignition switch position is ON.
• When the ignition switch is turned OFF, BCM operates timer for 15 minutes and then turns interior room
lamp relay OFF to cut the interior room lamp power supply.
NOTE:
When the ignition switch is turned OFF and all door is locked, BCM operates timer for 10 seconds and then
turns interior room lamp relay OFF to cut the interior room lamp power supply.
• BCM restart the timer when any of the following signal changes while operating the timer.
- Ignition switch status
- Key switch signal
- Door switch signal
- Back door switch signal
- Door lock/unlock signal (remote keyless entry receiver, door lock and unlock switch, each door request
switch)
ILLUMINATION CONTROL SYSTEM
ILLUMINATION CONTROL SYSTEM : System Description INFOID:0000000010430903
SYSTEM DIAGRAM
JMLIA5150GB
OUTLINE
Each illumination lamp is controlled by each function of BCM, IPDM E/R and combination meter.
Control by BCM
• Parking, license plate and tail lamp control function
• Combination switch reading function
• Auto light function
Control by IPDM E/R
• Relay control function
INL-12
SYSTEM
< SYSTEM DESCRIPTION >
Control by combination meter
• Illumination control function A
ILLUMINATION CONTROL
• BCM detects the combination switch condition by the combination switch reading function.
• BCM transmits position light request signal to IPDM E/R and combination meter according to tail lamp ON B
condition. Refer to EXL-26, "PARKING, LICENSE PLATE AND TAIL LAMP SYSTEM : System Description"
(LED headlamp) or EXL-195, "PARKING, LICENSE PLATE AND TAIL LAMP SYSTEM : System Descrip-
tion" (halogen headlamp).
C
• IPDM E/R turns the integrated smart FET ON according to position light request signal. It provides the power
supply to illumination lamp.
• Combination meter enters in the nighttime mode according to position light request signal and provides the
power supply to illumination lamp. D
SPICY ILLUMINATION CONTROL SYSTEM
SPICY ILLUMINATION CONTROL SYSTEM : System Description INFOID:0000000010335134
E
SYSTEM DIAGRAM
F
J
JMLIA5151GB
OUTLINE
Spicy illumination is controlled by each function or BCM and combination meter. K
Control by BCM
• Combination switch reading function
• Auto light function INL
INL-13
DIAGNOSIS SYSTEM (BCM)
< SYSTEM DESCRIPTION >
DIAGNOSIS SYSTEM (BCM)
COMMON ITEM
COMMON ITEM : CONSULT Function (BCM - COMMON ITEM) INFOID:0000000010501099
APPLICATION ITEM
CONSULT performs the following functions via CAN communication with BCM.
SYSTEM APPLICATION
BCM can perform the following functions for each system.
NOTE:
It can perform the diagnosis modes except the following for all sub system selection items.
×: Applicable item
Diagnosis mode
System Sub system selection item
Work Support Data Monitor Active Test
Door lock DOOR LOCK × ×
Rear window defogger REAR DEFOGGER × ×
Warning chime BUZZER × ×
Exterior lamp HEAD LAMP × × ×
Interior room lamp control INT LAMP ×
Wiper and washer WIPER × × ×
Turn signal and hazard warning lamps FLASHER × ×
— AIR CONDITONER* × ×
Intelligent Key system INTELLIGENT KEY × × ×
Combination switch COMB SW ×
Body control system BCM ×
NVIS - NATS IMMU ×
Interior room lamp battery saver BATTERY SAVER ×
Back door open TRUNK ×
Vehicle security THEFT ALM × ×
RAP RETAINED PWR ×
Remote keyless entry system MULTI REMOTE ENT × ×
Signal buffer system SIGNAL BUFFER × ×
NOTE:
*: This item is displayed, but not used.
FREEZE FRAME DATA (FFD)
The BCM records the following vehicle condition at the time a particular DTC is detected, and displays on
CONSULT.
INL-14
DIAGNOSIS SYSTEM (BCM)
< SYSTEM DESCRIPTION >
NOTE:
VEHICLE COND —
This item is displayed, but cannot be use this item.
C
NOTE:
DOOR LOCK STATUS —
This item is displayed, but cannot be use this item.
POWER SUPPLY
min Displays the cumulative time from the time that the battery terminal is connected. D
COUNTER
INT LAMP
E
INT LAMP : CONSULT Function (BCM - INT LAMP) INFOID:0000000010335139
WORK SUPPORT
F
Service item Setting item Setting
1 With interior room lamp timer function
On*
SET I/L D-UNLCK INTCON G
Off Without interior room lamp timer function
Monitor item
N
Description
[Unit]
REQ SW-DR
Indicated [On/Off] condition of door request switch (driver side) O
[On/Off]
REQ SW-AS
Indicated [On/Off] condition of door request switch (passenger side)
[On/Off]
PUSH SW P
Indicates [On/Off] condition of push-button ignition switch
[On/Off]
DOOR SW-DR
Indicated [On/Off] condition of front door switch (driver side)
[On/Off]
DOOR SW-AS
Indicated [On/Off] condition of front door switch (passenger side)
[On/Off]
INL-15
DIAGNOSIS SYSTEM (BCM)
< SYSTEM DESCRIPTION >
Monitor item
Description
[Unit]
DOOR SW-RR
Indicated [On/Off] condition of rear door switch RH
[On/Off]
DOOR SW-RL
Indicated [On/Off] condition of rear door switch LH
[On/Off]
DOOR SW-BK
Indicated [On/Off] condition of back door switch
[On/Off]
CDL LOCK SW
Indicated [On/Off] condition of lock signal from door lock and unlock switch
[On/Off]
CDL UNLOCK SW
Indicated [On/Off] condition of unlock signal from door lock and unlock switch
[On/Off]
KEY CYL LK-SW NOTE:
[On/Off] This item is displayed, but cannot be monitored
KEY CYL UN-SW NOTE:
[On/Off] This item is displayed, but cannot be monitored
RKE-LOCK
Indicates [On/Off] condition of LOCK signal from Intelligent Key
[On/Off]
RKE-UNLOCK
Indicates [On/Off] condition of UNLOCK signal from Intelligent Key
[On/Off]
KEY SW NOTE:
[On/Off] This item is displayed, but cannot be monitored
ACTIVE TEST
BATTERY SAVER
BATTERY SAVER : CONSULT Function (BCM - BATTERY SAVER) INFOID:0000000010335140
DATA MONITOR
NOTE:
The following table includes information (items) inapplicable to this vehicle. For information (items) applicable
to this vehicle, refer to CONSULT display items.
Monitor item
Description
[Unit]
REQ SW-DR
Indicated [On/Off] condition of door request switch (driver side)
[On/Off]
REQ SW-AS
Indicated [On/Off] condition of door request switch (passenger side)
[On/Off]
PUSH SW
Indicates [On/Off] condition of push-button ignition switch
[On/Off]
DOOR SW-DR
Indicated [On/Off] condition of front door switch (driver side)
[On/Off]
DOOR SW-AS
Indicated [On/Off] condition of front door switch (passenger side)
[On/Off]
DOOR SW-RR
Indicated [On/Off] condition of rear door switch RH
[On/Off]
DOOR SW-RL
Indicated [On/Off] condition of rear door switch LH
[On/Off]
INL-16
DIAGNOSIS SYSTEM (BCM)
< SYSTEM DESCRIPTION >
Monitor item
Description
[Unit] A
DOOR SW-BK
Indicated [On/Off] condition of back door switch
[On/Off]
CDL LOCK SW B
Indicated [On/Off] condition of lock signal from door lock and unlock switch
[On/Off]
CDL UNLOCK SW
Indicated [On/Off] condition of unlock signal from door lock and unlock switch
[On/Off] C
KEY CYL LK-SW NOTE:
[On/Off] This item is displayed, but cannot be monitored
KEY CYL UN-SW NOTE: D
[On/Off] This item is displayed, but cannot be monitored
RKE-LOCK
Indicates [On/Off] condition of LOCK signal from Intelligent Key
[On/Off] E
RKE-UNLOCK
Indicates [On/Off] condition of UNLOCK signal from Intelligent Key
[On/Off]
KEY SW NOTE: F
[On/Off] This item is displayed, but cannot be monitored
INTELLIGENT KEY
G
INTELLIGENT KEY : CONSULT Function (BCM - INTELLIGENT KEY) (Type 1)
INFOID:0000000010506515
H
WORK SUPPORT
INL-17
DIAGNOSIS SYSTEM (BCM)
< SYSTEM DESCRIPTION >
Monitor item Description
Reminder function (Intelligent Key) mode can be selected from the following with this mode
ANSWER BACK KEYLESS LOCK
• On: hazard warning lamp operate
UNLOCK
• Off: hazard warning lamp operate
NOTE:
WELCOME LIGHT OP SET
This item is indicated, but not used
SELF-DIAG RESULT
Refer to BCS-90, "DTC Index".
DATA MONITOR
NOTE:
The following table includes information (items) inapplicable to this vehicle. For information (items) applicable
to this vehicle, refer to CONSULT display items.
INL-18
DIAGNOSIS SYSTEM (BCM)
< SYSTEM DESCRIPTION >
Monitor Item Condition
A
NOTE:
PRMT RKE STRT
This item is displayed, but cannot be monitored
Indicates [KEY On/NOT On] condition of Intelligent Key ID and Intelligent Key is detected inside
I-KEY OK FLAG B
vehicle
PRBT ENG STRT Indicates whether or not the engine is in start prohibited status
Indicates whether or not it is in engine start possible status when Intelligent Key verification is
ID AUTHENT CANCEL TIMER C
unnecessary
ACC BATTERY SAVER Indicates [On/Off] whether or not ignition battery saver is in operation
Indicates [On/Off] whether or not in cranking prohibited status due to starter motor protection
CRNK PRBT TMR D
function operation
AUT CRANK TMR Indicates [On/Off] whether or not in AUTO CRANKING MODE status
CRNK PRBT TME Indicates the time for changing from cranking prohibited status to cranking possible status E
AUT CRANK TMR Indicates the time that AUTO CRANKING MODE operates
CRANKING TME Indicates the cranking operation time
NOTE: F
SHORT CRANK
This item is displayed, but not used
When remote keyless entry receiver receives the signal transmitted while operating on Intelli-
RKE OPE COUN1
gent Key, the numerical value start changing G
NOTE:
RKE OPE COUN2
This item is displayed, but cannot be monitored
S/L IGN OFF POSITION Indicates [On/Off] condition of Ignition OFF signal H
S/L SENSOR CIRCUIT 1 Indicates [Gnd/Off] condition of steering lock unit sensor circuit
S/L SENSOR CIRCUIT 2 Indicates [On/Off] condition of steering lock unit sensor circuit
I
S/L POWER OUTPUT Indicates [On/Off] condition of steering lock unit power supply
S/L POWER CHECK Indicates [On/Off] condition of steering lock unit power supply
ANTICIPATED POWER Indicates [On/Off] condition of anticipated power supply J
S/L LOCK REQ Indicates [On/Off] condition of steering lock unit lock request signal
S/L - BCM (CAN) Indicates [On/Off] condition of CAN communication
K
S/L POWER ERROR Indicates [On/Off] condition of steering lock unit power supply error
VEH SPEED ERROR (S/L) Indicates [On/Off] condition of vehicle speed signal
VEH SPEED NORMAL (S/L) Indicates [On/Off] condition of vehicle speed signal INL
ENGINE RUNNING (S/L) Indicates [On/Off] condition of engine running
S/L ID DISCORD Indicates [Correct/Incorrect] condition of ID verification
M
S/L ANTI-SCAN MODE Indicates [On/Off] condition of antiscan mode
S/L LOCK NOT PERMIT Indicates [Inhibition/No inhbt] condition of inhibit steering lock
S/L UNLOCK (CAN) Indicates [Finished/Unfinished] condition of steering lock unit unlock N
S/L ID STATUS (CAN) Indicates [Coded/Blank] condition of registration ID
S/L RESET STATUS (CAN) Indicates [Exit/No exit] condition of steering lock unit reset signal
S/L LO-LEVEL MALFUNC (CAN) Indicates [Malf/No malf] condition of lo-level malfunction O
S/L LOCK POSITION (CAN) Indicates [Armed/Malf/Unlocked/Undefined] condition of lock/unlock position signal
S/L ACT MALFUNCTION (CAN) Indicates [Malf/No malf] condition of steering lock unit malfunction
P
S/L HI-LEVEL MALFUNC (CAN) Indicates [Malf/No malf] condition of hi-level malfunction
S/L OPERATION PRHBT (SPD) Indicates [On/Off] condition of vehicle speed signal
S/L OPERATION PRHBT (PWR) Indicates [Allowed/Forbid] condition of safety line inhibition
S/L SENSOR POWER (CAN) Indicates [On/Off] condition of sensor test power supply
S/L SEN TEST PERMIT (CAN) Indicates [Forbid/Authorize] condition of sensor test
S/L STAT NOT DETECT (CAN) Indicates [Ok/Undefind] condition of steering lock undefined position signal
INL-19
DIAGNOSIS SYSTEM (BCM)
< SYSTEM DESCRIPTION >
Monitor Item Condition
S/L LOCKING FINISHED (CAN) Indicates [Unfinshd/Finished] condition of steering lock unit lock status signal
STOP/START SW Indicates [On/Off] condition of stop/start off switch
RKE-LOCK Indicates [On/Off] condition of LOCK signal from Intelligent Key
RKE-UNLOCK Indicates [On/Off] condition of UNLOCK signal from Intelligent Key
NOTE:
RKE-TR/BD
This item is displayed, but cannot be monitored
NOTE:
RKE-PANIC
This item is displayed, but cannot be monitored
RKE-MODE CHG Indicates [On/Off] condition of MODE CHANGE signal from Intelligent Key
NOTE:
RKE PBD
This item is displayed, but cannot be monitored
NOTE:
KEY SW
This item is displayed, but cannot be monitored
NOTE:
IGN SW
This item is displayed, but cannot be monitored
NOTE:
START SW
This item is displayed, but cannot be monitored
ACTIVE TEST
INL-20
DIAGNOSIS SYSTEM (BCM)
< SYSTEM DESCRIPTION >
Test item Description
A
This test is able to check BCM sends starter request signal to IPDM E/R via CAN communi-
cation
• MODE 1: IGN ON, START request OFF
ENGINE START REQUEST
• MODE 2: IGN OFF, START request ON B
• MODE 3: IGN ON, START request ON
• Off: Non-operation
NOTE:
IGNITION RELAY
This item is displayed, but cannot be used
C
This test is able to operate the starter control relay
STARTER CUT RELAY • On: Operates
• Off: Non-operation D
NOTE:
ENGINE START
This item is displayed, but cannot be used
This test is able to check back door opener actuator open operation E
TRUNK/BACK DOOR
Back door opener actuator opens when “Open” on CONSULT screen is touched
NOTE:
RETRACTABLE MIRROR
This item is displayed, but cannot be used F
NOTE:
REVERSE LAMP TEST
This item is displayed, but cannot be used
NOTE: G
KEYFOB P/W TEST
This item is displayed, but cannot be used
This test is able to check BCM sends power supply to audio unit or NAVI control unit
AUTO ACC 2 • On: Operate H
• Off: Non-operation
NOTE:
AUTOMATIC BACK DOOR
This item is displayed, but cannot be used
I
This test is able to check BCM sends power supply to ignition relay
AUTO ACC 1 • On: Operate
• Off: Non-operation
J
This test is able to check trunk room lamp operation
TRUNK/LUGGAGE LAMP
• On: Operates
TEST
• Off: Non-operation
K
INTELLIGENT KEY : CONSULT Function (BCM - INTELLIGENT KEY) (Type 2)
INFOID:0000000010506595
INL
WORK SUPPORT
INL-21
DIAGNOSIS SYSTEM (BCM)
< SYSTEM DESCRIPTION >
Monitor item Description
Auto door lock operation time can be changed in this mode
• MODE 1: OFF
• MODE 2: 30 sec
• MODE 3: 1 minute
AUTO LOCK SET
• MODE 4: 2 minutes
• MODE 5: 3 minutes
• MODE 6: 4 minutes
• MODE 7: 5 minutes
NOTE:
SHORT CRANKING OUTPUT
This item is displayed, but cannot be monitored
Ignition battery saver system mode can be changed to operation with this mode
IGN/ACC BATTERY SAVER • On: Operate
• Off: Non-operation
NOTE:
ANSWER BACK
This item is displayed, but cannot be used
Reminder function (door request switch) mode can be selected from the following with this
ANSWER BACK I-KEY LOCK UN- mode
LOCK • On: hazard warning lamp operate
• Off: hazard warning lamp operate
Reminder function (Intelligent Key) mode can be selected from the following with this mode
ANSWER BACK KEYLESS LOCK
• On: hazard warning lamp operate
UNLOCK
• Off: hazard warning lamp operate
NOTE:
WELCOME LIGHT OP SET
This item is indicated, but not used
SELF-DIAG RESULT
Refer to BCS-90, "DTC Index".
DATA MONITOR
NOTE:
The following table includes information (items) inapplicable to this vehicle. For information (items) applicable
to this vehicle, refer to CONSULT display items.
INL-22
DIAGNOSIS SYSTEM (BCM)
< SYSTEM DESCRIPTION >
Monitor Item Condition
A
IS STATUS - ECM Indicates [On/Off] condition of stop/start system
STARTER CUT RELAY - ECM Indicates [On/Off] condition of starter control relay signal from ECM via CAN communication
VEH SPEED 1 Display the vehicle speed signal received from combination meter by numerical value [Km/h] B
VEH SPEED 2 Display the vehicle speed signal received from ABS or VDC or TCM by numerical value [Km/h]
IGN REQ - IPDM Display the ignition request signal from IPDM E/R via CAN communication
STARTER REQ - IPDM Display the starter request signal from IPDM E/R via CAN communication C
DOOR STAT-DR Indicates [LOCK/READY/UNLK] condition of driver door status
DOOR STAT-AS Indicates [LOCK/READY/UNLK] condition of passenger door status
D
DOOR STAT-RR Indicates [LOCK/READY/UNLK] condition of rear door RH status
DOOR STAT-RL Indicates [LOCK/READY/UNLK] condition of rear door LH status
NOTE: E
BK DOOR STATE
This item is displayed, but cannot be monitored
ID OK FLAG Indicates [Set/Reset] condition of Intelligent Key ID
PRMT ENG STRT Indicates [Set/Reset] condition of engine start possible F
NOTE:
PRMT RKE STRT
This item is displayed, but cannot be monitored
Indicates [KEY On/NOT On] condition of Intelligent Key ID and Intelligent Key is detected inside
G
I-KEY OK FLAG
vehicle
PRBT ENG STRT Indicates whether or not the engine is in start prohibited status
H
Indicates whether or not it is in engine start possible status when Intelligent Key verification is
ID AUTHENT CANCEL TIMER
unnecessary
ACC BATTERY SAVER Indicates [On/Off] whether or not ignition battery saver is in operation
I
Indicates [On/Off] whether or not in cranking prohibited status due to starter motor protection
CRNK PRBT TMR
function operation
AUT CRANK TMR Indicates [On/Off] whether or not in AUTO CRANKING MODE status
J
CRNK PRBT TME Indicates the time for changing from cranking prohibited status to cranking possible status
AUT CRANK TMR Indicates the time that AUTO CRANKING MODE operates
CRANKING TME Indicates the cranking operation time K
NOTE:
SHORT CRANK
This item is displayed, but not used
When remote keyless entry receiver receives the signal transmitted while operating on Intelli- INL
RKE OPE COUN1
gent Key, the numerical value start changing
NOTE:
RKE OPE COUN2
This item is displayed, but cannot be monitored M
S/L IGN OFF POSITION Indicates [On/Off] condition of Ignition OFF signal
S/L SENSOR CIRCUIT 1 Indicates [Gnd/Off] condition of steering lock unit sensor circuit
N
S/L SENSOR CIRCUIT 2 Indicates [On/Off] condition of steering lock unit sensor circuit
S/L POWER OUTPUT Indicates [On/Off] condition of steering lock unit power supply
S/L POWER CHECK Indicates [On/Off] condition of steering lock unit power supply O
ANTICIPATED POWER Indicates [On/Off] condition of anticipated power supply
S/L LOCK REQ Indicates [On/Off] condition of steering lock unit lock request signal
S/L - BCM (CAN) Indicates [On/Off] condition of CAN communication
P
S/L POWER ERROR Indicates [On/Off] condition of steering lock unit power supply error
VEH SPEED ERROR (S/L) Indicates [On/Off] condition of vehicle speed signal
VEH SPEED NORMAL (S/L) Indicates [On/Off] condition of vehicle speed signal
ENGINE RUNNING (S/L) Indicates [On/Off] condition of engine running
S/L ID DISCORD Indicates [Correct/Incorrect] condition of ID verification
INL-23
DIAGNOSIS SYSTEM (BCM)
< SYSTEM DESCRIPTION >
Monitor Item Condition
S/L ANTI-SCAN MODE Indicates [On/Off] condition of antiscan mode
S/L LOCK NOT PERMIT Indicates [Inhibition/No inhbt] condition of inhibit steering lock
S/L UNLOCK (CAN) Indicates [Finished/Unfinished] condition of steering lock unit unlock
S/L ID STATUS (CAN) Indicates [Coded/Blank] condition of registration ID
S/L RESET STATUS (CAN) Indicates [Exit/No exit] condition of steering lock unit reset signal
S/L LO-LEVEL MALFUNC (CAN) Indicates [Malf/No malf] condition of lo-level malfunction
S/L LOCK POSITION (CAN) Indicates [Armed/Malf/Unlocked/Undefined] condition of lock/unlock position signal
S/L ACT MALFUNCTION (CAN) Indicates [Malf/No malf] condition of steering lock unit malfunction
S/L HI-LEVEL MALFUNC (CAN) Indicates [Malf/No malf] condition of hi-level malfunction
S/L OPERATION PRHBT (SPD) Indicates [On/Off] condition of vehicle speed signal
S/L OPERATION PRHBT (PWR) Indicates [Allowed/Forbid] condition of safety line inhibition
S/L SENSOR POWER (CAN) Indicates [On/Off] condition of sensor test power supply
S/L SEN TEST PERMIT (CAN) Indicates [Forbid/Authorize] condition of sensor test
S/L STAT NOT DETECT (CAN) Indicates [Ok/Undefind] condition of steering lock undefined position signal
S/L LOCKING FINISHED (CAN) Indicates [Unfinshd/Finished] condition of steering lock unit lock status signal
STOP/START SW Indicates [On/Off] condition of stop/start off switch
RKE-LOCK Indicates [On/Off] condition of LOCK signal from Intelligent Key
RKE-UNLOCK Indicates [On/Off] condition of UNLOCK signal from Intelligent Key
NOTE:
RKE-TR/BD
This item is displayed, but cannot be monitored
NOTE:
RKE-PANIC
This item is displayed, but cannot be monitored
RKE-MODE CHG Indicates [On/Off] condition of MODE CHANGE signal from Intelligent Key
NOTE:
RKE PBD
This item is displayed, but cannot be monitored
NOTE:
KEY SW
This item is displayed, but cannot be monitored
NOTE:
IGN SW
This item is displayed, but cannot be monitored
NOTE:
START SW
This item is displayed, but cannot be monitored
ACTIVE TEST
INL-24
DIAGNOSIS SYSTEM (BCM)
< SYSTEM DESCRIPTION >
Test item Description
A
This test is able to check security hazard lamp operation
FLASHER
The hazard lamps are activated after “LH/RH/Off” on CONSULT screen is touched
NOTE:
HORN B
This item is displayed, but cannot be used
This test is able to operate the blower relay in fuse block (J/B)
IGN CONT2 • On: Operates
• Off: Non-operation C
NOTE:
MIRROR +5
This item is displayed, but cannot be used
This test is able to check push-ignition switch illumination operation D
ENGINE SW ILLUMI
Push-ignition switch illumination illuminates when “ON” on CONSULT screen is touched
This test is able to check LOCK indicator in push-ignition switch operation
PUSH SWITCH INDICATOR
LOCK indicator in push-ignition switch illuminates when “ON” on CONSULT screen is touched E
This test is able to check BCM sends starter request signal to IPDM E/R via CAN communi-
cation
• MODE 1: IGN ON, START request OFF
ENGINE START REQUEST
• MODE 2: IGN OFF, START request ON
F
• MODE 3: IGN ON, START request ON
• Off: Non-operation
NOTE: G
IGNITION RELAY
This item is displayed, but cannot be used
This test is able to operate the starter control relay
STARTER CUT RELAY • On: Operates H
• Off: Non-operation
NOTE:
ENGINE START
This item is displayed, but cannot be used
I
This test is able to check back door opener actuator open operation
TRUNK/BACK DOOR
Back door opener actuator opens when “Open” on CONSULT screen is touched
NOTE: J
RETRACTABLE MIRROR
This item is displayed, but cannot be used
NOTE:
REVERSE LAMP TEST
This item is displayed, but cannot be used
K
NOTE:
KEYFOB P/W TEST
This item is displayed, but cannot be used
This test is able to check BCM sends power supply to audio unit or NAVI control unit
INL
AUTO ACC 2 • On: Operate
• Off: Non-operation
NOTE:
AUTOMATIC BACK DOOR M
This item is displayed, but cannot be used
This test is able to check BCM sends power supply to ignition relay
AUTO ACC 1 • On: Operate
• Off: Non-operation N
This test is able to check trunk room lamp operation
TRUNK/LUGGAGE LAMP
• On: Operates
TEST
• Off: Non-operation
O
INL-25
BCM
< ECU DIAGNOSIS INFORMATION >
ECU DIAGNOSIS INFORMATION
BCM
List of ECU Reference INFOID:0000000010430905
ECU Reference
BCS-64, "Reference Value"
BCS-88, "Fail-safe"
BCM
BCS-89, "DTC Inspection Priority Chart"
BCS-90, "DTC Index"
INL-26
INTERIOR ROOM LAMP CONTROL SYSTEM
< WIRING DIAGRAM >
WIRING DIAGRAM A
INTERIOR ROOM LAMP CONTROL SYSTEM
Wiring Diagram INFOID:0000000010430906
B
INL
JRLWD2035GB
INL-27
INTERIOR ROOM LAMP CONTROL SYSTEM
< WIRING DIAGRAM >
JRLWD2036GB
INL-28
INTERIOR ROOM LAMP CONTROL SYSTEM
< WIRING DIAGRAM >
INL
JRLWD2037GB
INL-29
INTERIOR ROOM LAMP CONTROL SYSTEM
< WIRING DIAGRAM >
JRLWD2233GB
INL-30
INTERIOR ROOM LAMP CONTROL SYSTEM
< WIRING DIAGRAM >
INL
JRLWD2234GB
INL-31
INTERIOR ROOM LAMP CONTROL SYSTEM
< WIRING DIAGRAM >
JRLWD2235GB
INL-32
INTERIOR ROOM LAMP CONTROL SYSTEM
< WIRING DIAGRAM >
INL
JRLWD2236GB
INL-33
INTERIOR ROOM LAMP CONTROL SYSTEM
< WIRING DIAGRAM >
JRLWD2237GB
INL-34
INTERIOR ROOM LAMP CONTROL SYSTEM
< WIRING DIAGRAM >
INL
JRLWD2238GB
INL-35
INTERIOR ROOM LAMP CONTROL SYSTEM
< WIRING DIAGRAM >
JRLWD2239GB
INL-36
INTERIOR ROOM LAMP CONTROL SYSTEM
< WIRING DIAGRAM >
INL
JRLWD2240GB
INL-37
ILLUMINATION
< WIRING DIAGRAM >
ILLUMINATION
Wiring Diagram INFOID:0000000010430907
JRLWD2038GB
INL-38
ILLUMINATION
< WIRING DIAGRAM >
INL
JRLWD2039GB
INL-39
ILLUMINATION
< WIRING DIAGRAM >
JRLWD2040GB
INL-40
ILLUMINATION
< WIRING DIAGRAM >
INL
JRLWD2041GB
INL-41
ILLUMINATION
< WIRING DIAGRAM >
JRLWD2241GB
INL-42
ILLUMINATION
< WIRING DIAGRAM >
INL
JRLWD2242GB
INL-43
ILLUMINATION
< WIRING DIAGRAM >
JRLWD2243GB
INL-44
ILLUMINATION
< WIRING DIAGRAM >
INL
JRLWD2244GB
INL-45
ILLUMINATION
< WIRING DIAGRAM >
JRLWD2245GB
INL-46
ILLUMINATION
< WIRING DIAGRAM >
INL
JRLWD2246GB
INL-47
ILLUMINATION
< WIRING DIAGRAM >
JRLWD2247GB
INL-48
ILLUMINATION
< WIRING DIAGRAM >
INL
JRLWD2248GB
INL-49
ILLUMINATION
< WIRING DIAGRAM >
JRLWD2249GB
INL-50
ILLUMINATION
< WIRING DIAGRAM >
INL
JRLWD2250GB
INL-51
DIAGNOSIS AND REPAIR WORK FLOW
< BASIC INSPECTION >
BASIC INSPECTION
DIAGNOSIS AND REPAIR WORK FLOW
Work Flow INFOID:0000000010430908
OVERALL SEQUENCE
JMKIA8652GB
DETAILED FLOW
INL-52
DIAGNOSIS AND REPAIR WORK FLOW
< BASIC INSPECTION >
1.GET INFORMATION FOR SYMPTOM A
1. Get detailed information from the customer about the symptom (the condition and the environment when
the incident/malfunction occurs).
2. Check operation condition of the function that is malfunctioning.
B
>> GO TO 2.
2.CHECK DTC C
1. Check DTC.
2. Perform the following procedure if DTC is detected.
- Record DTC and freeze frame data (Print them out using CONSULT.) D
- Erase DTC.
- Study the relationship between the cause detected by DTC and the symptom described by the customer.
3. Check related service bulletins for information. E
Are any symptoms described and any DTC detected?
Symptom is described, DTC is detected>>GO TO 3.
Symptom is described, DTC is not detected>>GO TO 4. F
Symptom is not described, DTC is detected>>GO TO 5.
3.CONFIRM THE SYMPTOM
Try to confirm the symptom described by the customer. G
Also study the normal operation and fail-safe related to the symptom.
Verify relation between the symptom and the condition when the symptom is detected.
H
>> GO TO 5.
4.CONFIRM THE SYMPTOM I
Try to confirm the symptom described by the customer.
Verify relation between the symptom and the condition when the symptom is detected.
J
>> GO TO 6.
5.PERFORM DTC CONFIRMATION PROCEDURE
Perform DTC CONFIRMATION PROCEDURE for the detected DTC, and then check that DTC is detected K
again. At this time, always connect CONSULT to the vehicle, and check self diagnostic results in real time.
If two or more DTCs are detected, refer to DTC INSPECTION PRIORITY CHART, and determine trouble diag-
nosis order. INL
NOTE:
• Freeze frame data is useful if the DTC is not detected.
• Perform Component Function Check if DTC CONFIRMATION PROCEDURE is not included on Service
M
Manual. This simplified check procedure is an effective alternative though DTC cannot be detected during
this check.
If the result of Component Function Check is NG, it is the same as the detection of DTC by DTC CONFIR-
MATION PROCEDURE. N
Is DTC detected?
YES >> GO TO 7.
NO >> Check according to GI-41, "Intermittent Incident". O
6.DETECT MALFUNCTIONING SYSTEM BY SYMPTOM DIAGNOSIS
Detect malfunctioning system according to SYMPTOM DIAGNOSIS based on the confirmed symptom in step P
4, and determine the trouble diagnosis order based on possible causes and symptom.
Is the symptom described?
YES >> GO TO 7.
NO >> Monitor input data from related sensors or check voltage of related module terminals using CON-
SULT.
7.DETECT MALFUNCTIONING PART BY DIAGNOSIS PROCEDURE
INL-53
DIAGNOSIS AND REPAIR WORK FLOW
< BASIC INSPECTION >
Inspect according to Diagnosis Procedure of the system.
Is malfunctioning part detected?
YES >> GO TO 8.
NO >> Check according to GI-41, "Intermittent Incident".
8.REPAIR OR REPLACE THE MALFUNCTIONING PART
1. Repair or replace the malfunctioning part.
2. Reconnect parts or connectors disconnected during Diagnosis Procedure again after repair and replace-
ment.
3. Check DTC. If DTC is detected, erase it.
>> GO TO 9.
9.FINAL CHECK
When DTC is detected in step 2, perform DTC CONFIRMATION PROCEDURE again, and then check that the
malfunction is repaired securely.
When symptom is described by the customer, refer to confirmed symptom in step 3 or 4, and check that the
symptom is not detected.
Is DTC detected and does symptom remain?
YES-1 >> DTC is detected: GO TO 7.
YES-2 >> Symptom remains: GO TO 4.
NO >> Before returning the vehicle to the customer, always erase DTC.
INL-54
INTERIOR ROOM LAMP POWER SUPPLY CIRCUIT
< DTC/CIRCUIT DIAGNOSIS >
DTC/CIRCUIT DIAGNOSIS A
INTERIOR ROOM LAMP POWER SUPPLY CIRCUIT
Diagnosis Procedure INFOID:0000000010430910
B
1.CHECK SYMPTOM
Check symptom (A or B). C
(+)
Interior room lamp relay (-) Voltage INL
Connector Terminal
1
M80 Ground Battery voltage M
6
Is the inspection result normal?
YES >> GO TO 4. N
NO >> Repair or replace harnesses.
4.CHECK INTERIOR ROOM LAMP RELAY 1
O
Check interior room lamp relay.
Refer to INL-56, "Component Inspection".
Is the inspection result normal?
P
YES >> GO TO 5.
NO >> Repair interior room lamp relay.
5.CHECK INTERIOR ROOM LAMP RELAY CIRCUIT 2
1. Disconnect map lamp connector.
2. Check continuity between interior room lamp relay harness connector and map lamp harness connector.
INL-55
INTERIOR ROOM LAMP POWER SUPPLY CIRCUIT
< DTC/CIRCUIT DIAGNOSIS >
INL-56
INTERIOR ROOM LAMP CIRCUIT
< DTC/CIRCUIT DIAGNOSIS >
INTERIOR ROOM LAMP CIRCUIT
A
Diagnosis Procedure INFOID:0000000010430942
NOTE: B
Before performing the diagnosis, check that the following items are normal.
• Interior room lamp power supply
• Map lamp bulb
• Room lamp bulb C
• Personal lamp bulb
• Vanity mirror lamp bulb
1.CHECK INTERIOR ROOM LAMP POWER SUPPLY CIRCUIT D
INL-57
INTERIOR ROOM LAMP CONTROL CIRCUIT
< DTC/CIRCUIT DIAGNOSIS >
INTERIOR ROOM LAMP CONTROL CIRCUIT
Component Function Check INFOID:0000000010430911
NOTE:
Before performing the diagnosis, check that the following items are normal.
• Interior room lamp power supply
• Map lamp bulb
• Room lamp bulb
• Personal lamp bulb
1.CHECK INTERIOR ROOM LAMP CONTROL FUNCTION
CONSULT ACTIVE TEST
1. Switch the map lamp switch, room lamp switch or personal lamp switch to DOOR.
2. Turn ignition switch ON.
3. Select “INT LAMP” of BCM (INT LAMP) active test item.
4. With operating the test items, check that each interior room lamp turns ON/OFF.
BCM
Test item Continuity
Connector Terminal
Ground
On Existed
M68 138 INT LAMP
Off Not existed
Is the inspection result normal?
YES >> GO TO 2.
NO-1 >> Continuity exists and remains unchanged: GO TO 3.
NO-2 >> Continuity does not exist and remains unchanged: Replace BCM. Refer to BCS-132, "Removal
and Installation".
2.CHECK INTERIOR ROOM LAMP CONTROL OPEN CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect BCM connector.
3. Check continuity between BCM harness connector and each interior room lamp harness connector.
INL-58
INTERIOR ROOM LAMP CONTROL CIRCUIT
< DTC/CIRCUIT DIAGNOSIS >
BCM F
Continuity
Connector Terminal Ground
M68 138 Not existed
G
Is the inspection result normal?
YES >> Replace BCM. Refer to BCS-132, "Removal and Installation".
NO >> Repair or replace harnesses. H
INL
INL-59
LUGGAGE ROOM LAMP CIRCUIT
< DTC/CIRCUIT DIAGNOSIS >
LUGGAGE ROOM LAMP CIRCUIT
Component Function Check INFOID:0000000010503097
NOTE:
Before performing the diagnosis, check that the following items are normal.
• Interior room lamp power supply
• Luggage room lamp bulb
1.CHECK LUGGAGE ROOM LAMP OPERATION
CONSULT ACTIVE TEST
1. Turn ignition switch ON.
2. Select “TRUNK/LUGGAGE LAMP TEST” of BCM (INTELLIGENT KEY) active test item.
3. With operating the test items, check that luggage room lamp turns ON/OFF.
BCM
Condition Continuity
Connector Terminal
Ground
Open Existed
B3 127 Back door
Closed Not existed
Is the inspection result normal?
YES >> GO TO 3.
NO-1 >> Continuity exists and remains unchanged: GO TO 4.
NO-2 >> Continuity does not exist and remains unchanged: Replace BCM. Refer to BCS-132, "Removal
and Installation".
3.CHECK LUGGAGE ROOM LAMP OPEN CIRCUIT
1. Disconnect BCM connector.
2. Check continuity between BCM harness connector and luggage room lamp harness connector.
INL-60
LUGGAGE ROOM LAMP CIRCUIT
< DTC/CIRCUIT DIAGNOSIS >
BCM
Continuity
Connector Terminal Ground E
B3 127 Not existed
Is the inspection result normal?
F
YES >> Replace BCM. Refer to BCS-132, "Removal and Installation".
NO >> Repair or replace harnesses.
INL
INL-61
SPICY ILLUMINATION CIRCUIT
< DTC/CIRCUIT DIAGNOSIS >
SPICY ILLUMINATION CIRCUIT
Component Function Check INFOID:0000000010503098
NOTE:
Before performing the diagnosis, check that Interior room lamp power supply is normal.
1.CHECK SPICY ILLUMINATION CONTROL FUNCTION
CONSULT ACTIVE TEST
1. Turn ignition switch ON.
2. Select “INT LAMP” of BCM (INT LAMP) active test item.
3. With operating the test items, check that spicy illumination turns ON/OFF.
BCM
Test item Continuity
Connector Terminal
Ground
On Existed
M70 72 INT LAMP
Off Not existed
Is the inspection result normal?
YES >> GO TO 3.
NO-1 >> Continuity exists and remains unchanged: GO TO 4.
NO-2 >> Continuity does not exist and remains unchanged: Replace BCM. Refer to BCS-132, "Removal
and Installation".
3.CHECK SPICY ILLUMINATION OPEN CIRCUIT
1. Disconnect BCM connector.
2. Check continuity between BCM harness connector and spicy illumination harness connector.
INL-62
SPICY ILLUMINATION CIRCUIT
< DTC/CIRCUIT DIAGNOSIS >
BCM E
Continuity
Connector Terminal Ground
M70 72 Not existed
F
Is the inspection result normal?
YES >> Replace BCM. Refer to BCS-132, "Removal and Installation".
NO >> Repair or replace harnesses.
G
INL
INL-63
PUSH-BUTTON IGNITION SWITCH ILLUMINATION CIRCUIT
< DTC/CIRCUIT DIAGNOSIS >
PUSH-BUTTON IGNITION SWITCH ILLUMINATION CIRCUIT
Component Function Check INFOID:0000000010430919
(+)
BCM (–) Condition Voltage
Connector Terminal
On 12 V
M69 88 Ground ENGINE SW ILLUMI
Off 0V
Is the inspection result normal?
YES >> GO TO 2.
NO >> GO TO 4.
2.CHECK PUSH-BUTTON IGNITION SWITCH ILLUMINATION CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect BCM connector and push-button ignition switch connector.
3. Check continuity between BCM harness connector and push-button ignition switch harness connector.
INL-64
PUSH-BUTTON IGNITION SWITCH ILLUMINATION CIRCUIT
< DTC/CIRCUIT DIAGNOSIS >
NO >> Repair or replace harnesses.
4.CHECK PUSH-BUTTON IGNITION SWITCH ILLUMINATION SHORT CIRCUIT A
BCM
Continuity C
Connector Terminal Ground
M69 88 Not existed
Is the inspection result normal? D
YES >> Replace BCM. Refer to BCS-132, "Removal and Installation".
NO >> Repair or replace harnesses.
E
INL
INL-65
INTERIOR LIGHTING SYSTEM SYMPTOMS
< SYMPTOM DIAGNOSIS >
SYMPTOM DIAGNOSIS
INTERIOR LIGHTING SYSTEM SYMPTOMS
Symptom Table INFOID:0000000010430921
NOTE:
Perform the self-diagnosis with CONSULT before the symptom diagnosis. Perform the trouble diagnosis if any
DTC is detected.
INL-66
INTERIOR LIGHTING SYSTEM SYMPTOMS
< SYMPTOM DIAGNOSIS >
Symptom Possible cause Inspection item
A
Door switch circuit
Refer to DLK-94,
"Component Function Check" (Type
1)*, DLK-284, B
• Harness between BCM and each
"Component Function Check" (Type
door switch
2)*, DLK-427,
• BCM
• Spicy illumination does not turn ON even "Component Function Check" (Type
though the door is open. 3)*, DLK-567, C
• Spicy illumination does not turn OFF even "Component Function Check" (Type
though the door is closed. 4)*.
• Harness between spicy illumination D
and interior room lamp relay
Spicy illumination circuit
• Harness between BCM and spicy il-
Refer to INL-62, "Component Function
lumination
Check".
• Spicy illumination E
• BCM
• Harness between BCM and push-
button ignition switch Push-button ignition switch illumination
F
Push-button ignition switch illumination does • Harness between push-button igni- circuit
not illuminate. tion switch and ground Refer to INL-64, "Component Function
• Push-button ignition switch Check".
• BCM G
• Harness between BCM and interior
Interior room lamp power supply circuit
Interior room lamp battery saver does not ac- room lamp relay
Refer to INL-55, "Diagnosis Proce-
tivate. • Interior room lamp relay
dure". H
• BCM
*: Refer to DLK-24, "Information" for detailed vehicle information.
I
INL
INL-67
MAP LAMP
< REMOVAL AND INSTALLATION >
REMOVAL AND INSTALLATION
MAP LAMP
Exploded View INFOID:0000000010430922
With sunroof
JMLIA5183ZZ
MAP LAMP
MAP LAMP : Removal and Installation INFOID:0000000010430923
REMOVAL
CAUTION:
Disconnect the battery negative terminal or remove power circuit fuse when performing the operation
for preventing electric leakage. Refer to INL-3, "Precautions for Removing Battery Terminal".
INL-68
MAP LAMP
< REMOVAL AND INSTALLATION >
1. Disengage lens fixing pawls using a remover tool (A), and then
remove lens . A
CAUTION:
Apply protect tape on remover tool.
B
: Pawl
JMLIA1063ZZ
D
2. Disengage map lamp housing fixing pawl using a remover tool
(A), and then pull out lamp housing according to numerical
order 1→2 indicated by arrows as shown in the figure.
CAUTION: E
Apply protect tape on remover tool.
: Pawl F
G
JMLIA1064ZZ
3. Disconnect map lamp harness connector, and then remove map lamp housing.
H
INSTALLATION
Install in the reverse order of removal.
I
MAP LAMP : Replacement INFOID:0000000010430924
: Pawl
M
N
JMLIA1063ZZ
2. Remove bulb.
O
MAP LAMP FINISHER
MAP LAMP FINISHER : Removal and Installation INFOID:0000000010451298 P
CAUTION:
Disconnect the battery negative terminal or remove power circuit fuse while performing the operation
to electric leakage. Refer to INL-3, "Precautions for Removing Battery Terminal".
REMOVAL
INL-69
MAP LAMP
< REMOVAL AND INSTALLATION >
1. Disengage map lamp assembly fixing pawls and metal clips
according to numerical order 1→3 indicated by arrows as shown
in the figure.
: Pawl
: Metal clip
JMLIA5190ZZ
INSTALLATION
Install in the reverse order of removal.
REMOVAL
1. Remove headlining assembly. Refer to INT-25, "Removal and Installation".
2. Remove map lamp bracket mounting bolts , and then remove
map lamp bracket.
JMLIA5191ZZ
INSTALLATION
Install in the reverse order of removal.
INL-70
VANITY MIRROR LAMP
< REMOVAL AND INSTALLATION >
VANITY MIRROR LAMP
A
Exploded View INFOID:0000000010430926
JMLIA5184ZZ
G
Lens Bulb Lens
: Pawl
H
Replacement INFOID:0000000010430927
INL-71
GLOVE BOX LAMP
< REMOVAL AND INSTALLATION >
GLOVE BOX LAMP
Exploded View INFOID:0000000010430928
LHD models
JMLIA5185ZZ
Replacement INFOID:0000000010430929
JMLIA3624ZZ
INL-72
SPICY ILLUMINATION
< REMOVAL AND INSTALLATION >
SPICY ILLUMINATION
A
Exploded View INFOID:0000000010430930
REMOVAL B
LHD models
C
JMLIA5186ZZ J
DISASSEMBLY INL
JMLIA5187ZZ
INL-73
SPICY ILLUMINATION
< REMOVAL AND INSTALLATION >
Console panel bracket RH Console panel mask lid RH Spicy illumination assembly
Console panel RH
: Clip
: Pawl
: Metal clip
: Vehicle front
Replacement INFOID:0000000010430932
JMLIA5192ZZ
JMLIA5193ZZ
INL-74
ROOM LAMP
< REMOVAL AND INSTALLATION >
ROOM LAMP
A
Exploded View INFOID:0000000010451272
JMLIA2093ZZ
G
Lamp housing Bulb Lens
: Pawl
: Vehicle front H
JMLIA1230ZZ
P
INL-75
ROOM LAMP
< REMOVAL AND INSTALLATION >
2. Disengage lamp housing fixing pawl using a remover tool (A),
and then pull out lamp housing according to numerical order
1→2 indicated by arrows as shown in the figure.
CAUTION:
Apply protect tape on remover tool.
: Pawl
JMLIA1231ZZ
INSTALLATION
Install in the reverse order of removal.
Replacement INFOID:0000000010451274
CAUTION:
• Disconnect the battery negative terminal or remove power circuit fuse while performing the opera-
tion to electric leakage. Refer to INL-3, "Precautions for Removing Battery Terminal".
• Never touch the glass surface of the bulb with bare hands or allow oil or grease to get on it to pre-
vent damage to the bulb.
• Never touch the glass surface of the bulb with bare hands because the surface is very hot just after
the lamp is turned OFF to prevent a burns.
• Leaving the bulb removed from housing for a long period of time can deteriorate performance of the
lens and reflector (causing dirty or clouding). Always prepare a new bulb and have it on hand when
replacing the bulb.
ROOM LAMP BULB
1. Disengage lens fixing pawls using a remover tool (A), and then
remove lens .
CAUTION:
Apply protect tape on remover tool.
: Pawl
JMLIA1230ZZ
2. Remove bulb.
INL-76
PERSONAL LAMP
< REMOVAL AND INSTALLATION >
PERSONAL LAMP
A
Exploded View INFOID:0000000010430933
I
JMLIA5188ZZ
REMOVAL
CAUTION: M
Disconnect the battery negative terminal or remove power circuit fuse when performing the operation
for preventing electric leakage. Refer to INL-3, "Precautions for Removing Battery Terminal".
1. Disengage personal lamp assembly fixing metal clips using a N
remover tool (A).
: Metal clip
O
JMLIA5194ZZ
INSTALLATION
INL-77
PERSONAL LAMP
< REMOVAL AND INSTALLATION >
Install in the reverse order of removal.
Replacement INFOID:0000000010430935
: Pawl
JMLIA5195ZZ
3. Remove bulb.
INL-78
LUGGAGE ROOM LAMP
< REMOVAL AND INSTALLATION >
LUGGAGE ROOM LAMP
A
Exploded View INFOID:0000000010430936
I
JMLIA5189ZZ
INL
REMOVAL
CAUTION:
Disconnect the battery negative terminal or remove power circuit fuse when performing the operation M
for preventing electric leakage. Refer to INL-3, "Precautions for Removing Battery Terminal".
1. Apply protective tape (A) to rear pillar finisher LH of surface for
protecting it from damage.
N
JMLIA5196ZZ
INL-79
LUGGAGE ROOM LAMP
< REMOVAL AND INSTALLATION >
2. Disengage luggage room lamp assembly fixing pawl using a
remover tool (A).
: Pawl
JMLIA5197ZZ
3. Disconnect harness connector, and then remove luggage room lamp assembly.
INSTALLATION
Install in the reverse order of removal.
Replacement INFOID:0000000010430938
: Pawl
JMLIA5247ZZ
3. Remove bulb.
INL-80
SERVICE DATA AND SPECIFICATIONS (SDS)
< SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS) A
SERVICE DATA AND SPECIFICATIONS (SDS)
bulb specifications INFOID:0000000010430941
B
INL
INL-81