ACT
SAFETY COMPLIANCE TESTING FOR
FMVSS No. 218 MOTORCYCLE HELMETS
Brand: ICH
Model: ICH-501
Size: XL (59-60 cm)
Toaalso include size L (57-58 cm), M(56 -57 em),$ (54 -55 em) with same shell and EPS liner size
Prepared For:
Comercializadora Inducascos S.A
Cra, 50gg #10B Sur
38 Medellin Columbia
21 September 2018
Final Report No.: 428.0008.001
Tested By:
ACT Lab LLC.
3280 East 59th Street
Long Beach CA, 90805
www.act-lab.com
This document shall not be reproduced except in full without written approval from ACT Lab LLC
‘This laboratory i acreited in accordance with the recognize international Standard ISONEC
170252008, This accreditation demonstrates technica competence fora defined "scope andthe
operation ofalaborataryqualty management sytem feferjontISO LAC “AF Communique dated
“Tanuary.2008) The lant Communiqué save able on pubkstons and resources page oftheILAC
ACCREDITED website at hntpurwmwiacorg, Accreditation st Ing. end. certiicate can. be found at
Atpsiwwasonineorg,
Contract File No: 428.0008 Technician: George Stetina
Test File: .001 Test Date: 21 September 2018
Control Document Rev.11 Offical ACT DOT Repert Template TP-07 USA 19 September 2018
‘T:LACT GLOBAL PORTAL \ACT Gobal Tempate Foier\Reports\2018 TEMPLATES HELMET\FMVSS 218ACT
TABLE OF CONTENTS
PURPOSE OF COMPLIANCE TEST..
HELMET DATA.
TEST DATA...
APPENDIX A.
INTERPRETATIONS OR DEVIATIONS FROM FMVSS 21:
APPENDIX B.
EQUIPMENT LIST AND CALIBRATION SCHEDULES.
APPENDIX C....
Contract File No: 428.0008 Technician: George Stetina
Test File: .001 Test Date: 21 September 2018
Control Document Rev.11 Offical ACT DOT Repert Template TP-07 USA 19 September 2018
‘T:LACT GLOBAL PORTAL \ACT Gobal Tempate Foier\Reports\2018 TEMPLATES HELMET\FMVSS 218ACT
PURPOSE OF COMPLIANCE TEST
Purpose:
The purpose of this test was to determine
if the motorcycle helmets supplied by:
Comercializadora Inducascos S.A
Met the requirements of
Federal Motor Vehicle Safety Standard
No. 218: Motorcycle Helmets effective
May 13, 2013.
All samples received were in good
condition and appropriate for these tests.
Test Procedure:
This test was performed following
TP-218-07 and ACT Lab Helmet Testing
Manual 4.2
Contract File No: 428.0008 Technician: George Stetina
Test File: .001 Test Date: 21 September 2018
Contral Document Rev.11 Oficial ACT DOT Report Template TP-07 USA 19 September 2018
‘T:LACT GLOBAL PORTAL \ACT Gobal Tempate Foier\Reports\2018 TEMPLATES HELMET\FMVSS 218ACT
HELMET DATA
HELMET BRAND NAME: ICH
HELMET MODEL DESIGNATION:
HELMET MANUFACTURER: Comercializadora Inducascos
HELMET SIZE: XL (59 -60.cm)
HELMET COVERAGE: Partial: Full: Complete: xX
HELMET POSITIONING INDEX: 52mm
SHELL MATERIAL: —_Injection Molded ABS
LINER MATERIAL: —_ Expanded Polystyrene
BUCKLE DESCRIPTION: Quick Release Ratchet
A B c D E
HELMET! Ambient | LowTemp | HighTemp _| Waterimmersed Spare
oe PATTERN Black/Red | Black/Red | Black/Red Black/Red | Black/Red
WEIGHT (grams) 1303 1308 1311 1311 1485
MONTH & YEAR OF
MANUFACTURE 09/2018 | 09/2018 | 09/2018 09/2018 09/2018
COMMENTS:
All helmets were received in undamaged condition and were appropriate for testing
Weights listed above forhelmets A -D areastested with face shield and visor removed.
Weight for helmet is complete with all components in place.
The HPI is based on information obtained from the manufacturer.
This test report applies to the additional consumers sizes of: size L (58 -59.cm),M(56 -57
cm),$ (54 -55¢m) asthe se sizes use the exact. sameshelland EPS liner as tested size
XL (59 -60.cm)
yaeno
Contract File No: 428.0008 Technician: George Stetina
Test File: .001 Test Date: 21 September 2018
Control Document Rev.11 Offical ACT DOT Repert Template TP-07 USA 19 September 2018
‘T:LACT GLOBAL PORTAL \ACT Gobal Tempate Foier\Reports\2018 TEMPLATES HELMET\FMVSS 218ACT
SUMMARY OF TEST RESULTS
INDICATE Pass or Fail
HELMET A 8 ¢ D
Low HIGH WATER
Test AMBIENT TEMP TEMP IMMERSED
Impact
PENETRATION
RETENTION,
INDICATE Pass or Fail
Test PASS/ FAIL
PERIPHERAL VISION Pass
PROJECTIONS. Pass
LABELING Pass
Contract File No: 428.0008 Technician: George Stetina
Test File: .001 Test Date: 21 September 2018
Control Document Rev.11 Offical ACT DOT Repert Template TP-07 USA 19 September 2018
‘T:LACT GLOBAL PORTAL \ACT Gobal Tempate Foier\Reports\2018 TEMPLATES HELMET\FMVSS 218