5. WTs internal loadbearing or protected
stairwell/integral garage wall (REI 30 minutes)
INNER AND
OUTER FACE
INSULATION
LUNSHEATHED
Prion.
‘SHEATHED
Prion.
VERIFICATION DETAILS.
Based on esting to BS EN 1365-1:2012 ade)
Load applied 100% of in-service design capacity
Fold of application Wllpanels upto 2.7m high
3rd party peer review BRE
MATERIAL FIXING
+x minimum 16mm Type A or FplastrbarAlots
mesh tped anc iled
NOTE: Hotzntal bord ons requre minim
38mm x 83mm C16 tnbernogins at bard int
Optional -fo acoustcthermal purposes, fl pata fl,
mineral wooo iret (glass or stone woo)
NOTE: Tre action of mineral wot insulation es 0
detrimental impact on the fre restance perfomance
Nirman 38mm x 89mm C16 LS tinder @ 600mm CTRS
NOTE: The action of studs ose centres and mute
stu ster, as no detrimental impact on fe restance
erfranes
“xv 38mm x89 C16 CLS tnber mid height roogts,
staggered
NOTE: The action of iit regan has no dnt
Iingact on re rsistnce perfomance
Nirimum Grim stething (0SB/3, pod or euo-cass At?
‘2boardng)
NOTE: Sheathing san optional requiement fr stuctual
uapeses
NOTE: Te cision of sheathing has no detnetatimaac on
fre restance
Timber ancy or stucurlnogins, as requted
NOTE: The action of ropgns has no detent impact on
the fe restanes perfomance
Inaccrdanoe with B, Kraul or Sia fangs requirements
“Typical, 3mm x 36mm se-apping diya scens
@ minum 300mm CTS
Friction fed without tings
In accordance with sruccal engineer's ing requirements
“Typical, 3:1 mm x 86min ts sherk nals, 2p stud
In accordance with sruccal engineer's ing requirements
‘pial, 31mm x BG vis shark nals 2 pe tudhoggh
connection
In accordance with sruccal engineer's ing requirements
‘pial, 2:81nm x Om smth shank als @ 160mm
TRS (perimeter) and 300mm GTRS frtemedate sts)
“Typical 31 mm x Erm vist sharks, 2 pa stu to
ogain
a °2
6. WT6 internal loadbearing or protected stairwell/
enclosure wall (REI 60 minutes)
\VERIFIOATION DETAILS
TER AND
OUTER FACE:
INSULATION
LUNSHEATHED
‘OPTION
SHEATHED
‘OPTION
TIMBER BULOM
Based on testing to
Load applied
Fold of application
BSEN 1965-1:2012 oad)
10035 of in-service design capacity
Wal panes up to 2.7m hgh
rd party peer review BRE
MATERIAL
Fil layer - 1 minimum 16mm Type A D oF plasterboard
‘Ants mesh taped and filed
NOTE: Plasterboard to have stagoered vert joints
Fist yer -1 x irimam 15m Type A. orF plasterboard,
Te toad jis do nt need to be taped ae ad
NOTE: Horzontal board joints in bot layers, require minimum)
38min x 6m C6 tnber regs at bad jit
Optonl -for acoustical poses lor pri i,
mineral woo rl isuon (asso stone woo)
‘NOTE: The adlton of mineral woainsuaton has ro
etimenta impact onthe ie resstanceperfonnance
Minimum 38mm x Grim C16 CLS smber @ GOdrnn CTS
NOTE: The ado of sts at ser centres and muticle
stud cists, has no deinen impacto fe resistance
performance
+ crow 38mm, Ben O16 CLS tnber mid height nga,
staggered
NOTE: The alton of mio-eight nog fs 0 dimen
ingact on ie resistance perfomance
Mrimum arm sheathing (S813, iyi cr euo-classA1/
#2 boating]
NOTE: Sheathing's an optoal requirement for stuctual
purposes
NOTE: The atlon of sheathing has no dtrinsntl impact on
fre esstance perfomance
Tiber ancy or structural noggin 2s requ
NOTE: The ation of rogpns has oo oriental impact 00
the re resstanceperinmance
FRE.
Inaceordance with BG, Knauf or Sra ings equitererts
‘Wplcaly, 35mm x 60mm seappng drywall sens
@ maximum 300mm CTRS
In accordance with BG, Kraut Sra ings ecuierents
‘Wally, 35mm x 38mm seappng drywall sxens
@ maximum 300mm CTRS
Friction fied wth ings
In accordance with structural engineer's ng requemets
Typically, 3mm x 86mm twist shanks, 2p stud
In accordance with structural engineer's ng requemets
Typically, 3mm x 86mm ts shanks, 2 pe tudoagin
connection
In accordance with structural engineer's ng requemets
Typically 281mm x Om smooth stank als @ 150mm
TRS (pexineter and 300mm OTRS(itmedate sts)
“Tycally31en x 88mm ist shank nals, 2 per stud to
recog
TA