Professional Documents
Culture Documents
signal
test
+
both sides
transmitter terminal
circuitry connections
this side this side
-
mounting braket,
U-bolt, nuts and vent valves cable to enter
washers are inclued through lower shield to be
in delivery. conduit connected at
this end only.
to measuring unit
electrical cabinet
ALTERNATIVE
MOUNTING
dn50 or nps 2" (od=60-62mm)pipe
rigidly mounted/weled to
adjacent bulkhead or suitable
mounting surface.
ALTERNATIVE
MOUNTING
CUSTOMER
REF DWG NO
CAD FILE
VIKING ENGINEERING PTE LTD ISO 9001 2000 REGISTERED
184 PANDAN LOOP, SINGAPORE 128374 MGMT. SYS.
RvA C 0 2 4
DRAWN Tel: +65 6777 5055 Fax: +65 6779 2176 Mail: info@viking.sg Web: www.viking.sg
DNV Certification B.V., The Nethelands
APPROVED PROJECT
1ST ANGLE PROJECTION
DWG TITLE
installation of dp/i-transmitter with 5-way valve block
THE INFORMATION CONTAINED
HEREIN IS THE EXCLUSIVE PROPERTY
DWG NO REV
OF VIKING ENGINEERING PTE LTD.
THEY MUST NOT BE USED OR
REPRODUCED IN WHOLE OR IN PART
DATE SCALE PAGE SIZE
WITHOUT PERMISSION IN WRITING. A3
REV REVISION NOTE DATE ISSUED
CUSTOMER
REF DWG NO
CAD FILE
VIKING ENGINEERING PTE LTD ISO 9001 2000 REGISTERED
184 PANDAN LOOP, SINGAPORE 128374 MGMT. SYS.
RvA C 0 2 4
DRAWN Tel: +65 6777 5055 Fax: +65 6779 2176 Mail: info@viking.sg Web: www.viking.sg
DNV Certification B.V., The Nethelands
APPROVED PROJECT
1ST ANGLE PROJECTION
DWG TITLE
GENERAL ARRANGEMENT OF FLOW SENSOR AND DP/I TRANSMITTER
THE INFORMATION CONTAINED
HEREIN IS THE EXCLUSIVE PROPERTY
DWG NO REV
OF VIKING ENGINEERING PTE LTD.
THEY MUST NOT BE USED OR
REPRODUCED IN WHOLE OR IN PART
DATE SCALE PAGE SIZE
WITHOUT PERMISSION IN WRITING. A3
REV REVISION NOTE DATE ISSUED
PROCEDURE FOR INSTALLATION OF SAMPLING PROBE
1. Determine location of sampling point. The sampling point should
normally be located in a vertical section of the discharge line. If
mounted in a horizontal section the probe should penetrate from the
lower part of the pipe.
2. On sampling point site arrange a Ø = 42-44 mm hole which will
provide enough weld bead.
FLOW 3. Determine mounting stub height "H" acc. to table.
4. Cut and shape item ‚ to comply with determined "H" and
discharge pipe periphery.
5. Align item ‚ concentrically over the hole and weld it to the pipe.
6. Install flange gasket † , and slide sampling probe •, into the
TO SAMPLE stub so that the arrow is pointing in the flow direction.
DN20(3/4")PN16 FEED PUMP 7. Complete installation by bolting probe flange to mating stub
DIN2576 flange.
8. Cut / drill a Ø = 34-35 mm hole in the discharge line at a
distance minimum 150 mm downstream of the sample probe and fit the
sample return stub by continuos weld.
DN50(2")PN16 - Alternative installation method may be used provided requirements
DIN2527/B for "H" as for classification are considered.
FROM EJECTOR
DN25(1")PN16 - For dimensions not contained in the table, use the formula.
DN50(2")PN16 DIN2576
DIN2576
TABLE FOR DETERMINEING "H"
Dia. Nom. OD H for t = H
(Nom. pipe MM 4.5-12.7 mm for odd pipe sizes
size) ( IN. ) ( 0.175-0.5 in.) use below formula
DN 50 60
116
(NPS 2) ( 2.38 )
DN 65 73
114
(NPS 2 1/2) ( 2.88 )
DN 80 89
110
(NPS 3) ( 3.5 )
DN50 T=6.3 DN25 T=4.0
OD=60.3 OD=33.7 DN 90 102
106
(NPS 3 1/2) (4)
H = 135 - OD/4 - T/2
FULL PENETRATION DN 100 114
103
WELD! TRIM EDGE (NPS 4) ( 4.5 )
TO FIT PIPE!
DN 125 141
96
(NPS 5) ( 5.56 )
DN 150 168
90
(NPS 6) ( 6.62 )
DN 200 219
76
(NPS 8) ( 8.62 )
SAMPLE INCLUDED IN DELIVERY FROM VIKING
OUT 1. Sampling probe, DN50 - DN200, L = 135
2. Mounting stub, H = 150 at delivery, to be adjusted at installation.
SAMPLE IN 3. NUT, M16 16
4. Washer, brb 17X30
5. Bolt, M6s 16X60
6. Gasket
DISCHARGE WATER 7. Sample return stub, L = 100
FLOW DIRECTION STUB MATERIAL: DIN ST35.8/1
SIS 1330-05
CUSTOMER
REF DWG NO
CAD FILE
VIKING ENGINEERING PTE LTD ISO 9001 2000 REGISTERED
184 PANDAN LOOP, SINGAPORE 128374 MGMT. SYS.
RvA C 0 2 4
DRAWN Tel: +65 6777 5055 Fax: +65 6779 2176 Mail: info@viking.sg Web: www.viking.sg
DNV Certification B.V., The Nethelands
APPROVED PROJECT
DWG TITLE
1ST ANGLE PROJECTION SAMPLING PROB AND RETURN STUB FOR DISCHARGE PIPES
THE INFORMATION CONTAINED DN50-DN200 (NPS2-NPS8) ASSEMBLY AND MOUNTING
HEREIN IS THE EXCLUSIVE PROPERTY
DWG NO REV
OF VIKING ENGINEERING PTE LTD.
THEY MUST NOT BE USED OR
REPRODUCED IN WHOLE OR IN PART
DATE SCALE PAGE SIZE
WITHOUT PERMISSION IN WRITING. A3
ó ͱ´·¼ ¿²¼ ½±³°¿½¬ ¼»-·¹²
б-·¬·±² ·²¼·½¿¬±®
ݱ²¼«·¬ »²¬®·»-
ÒßÓËÎ ÍÌßÒÜßÎÜ