Professional Documents
Culture Documents
TM
Serial
Number
Decal
• Assembly
• Operation
• Troubleshooting
For your benefit, read this manual carefully before Before reading further, please familiarize yourself with
you use the vibration platform. If you have ques- the parts that are labeled in the drawing below.
tions after reading this manual, please see the back
Console
Handlebar
Dumbbell
Weight Rest
Power Cord
Start Button
Base
©D M4 x 16mm M4 x 19mm
M10 Nylon MIO Split Patch Screw (26) Screw (45)
Locknut (32) Washer (38)
M!O x 50mm Patch Screw (5!) M10 x 55mm Patch Screw (20)
H
M!0 x 62ram Patch Screw (37) M10 x 68mm Bolt (55)
6
Downloaded from www.Manualslib.com manuals search engine
ASSEMBLY
• Place all parts in a cleared area and remove the Assembly will be more convenient if you have a
packing materials. Do not dispose of the packing socket set, a set of open-end or closed-end
materials until assembly is completed. wrenches, or a set of ratchet wrenches.
Base
Wire
20 38
40
40
40
ire Tie
43
28
27
10
26
11
42 Slots
17
16. Make sure that all parts are properly tightened before you use the vibration platform.
12
Wheel
Dumbbell
Dumbbell
13
14
15
See HOW TO TURN ON THE POWER on page See HOW TO TURN ON THE POWER on page
15. 15.
2. Select the desired vibration time. 2. Insert an iFIT card and select a program.
Press the desired time button to select a vibration To use an iFIT program, insert an iFIT card into
time of 30, 45, or 60 seconds. The display will the iFIT slot; make sure that the iFIT card is ori-
show which length of time you have selected. ented so the metal contacts are face down and
are facing the slot. When the iFIT card is properly
3. Select the desired vibration frequency. inserted, the indicator next to the slot will light and
the number of the iFIT program will appear in the
Press the desired frequency button to select a display.
vibration frequency of 25, 30, or 35 hertz. The dis-
play will show which frequency you have selected.
5. Stop or pause a vibration session. A moment after you select a program, the voice of
a personal trainer will begin guiding you through
Press the stop button (see the drawing above) on your workout.
the platform to stop or pause a vibration session.
Press the start button to continue the vibration ses- . When you are finished exercising, remove the
sion. iFIT card.
Note: When the session ends, a tone will sound to Remove the iFIT card when you are finished exer-
alert you, and the vibration platform will automati- cising. Store the iFIT card in a secure place.
cally stop.
16
Most vibration platform problems can be solved by following the simple steps below. Find the symptom
that applies, and follow the steps listed. If further assistance is needed, call the telephone number listed
on the back cover of this manual.
SOLUTION: a. Make sure that the power cord is plugged into a surge suppressor, and that the surge suppres-
sor is plugged into a properly grounded outlet (see page 14). Use only a single-outlet surge sup-
pressor that meets all of the specifications described on page 14. IMPORTANT: The vibration
platform is not compatible with GFCl-equipped outlets.
c
b. Check the reset/off circuit breaker located on the
vibration platform frame near the power cord. If
the switch protrudes as shown, the circuit breaker
has tripped. To reset the circuit breaker, wait for
five minutes and then press the switch back in. Tripped Reset
SOLUTION: a. Check the reset/off circuit breaker (see the drawing above). If the circuit breaker has tripped,
wait for five minutes and then press the switch back in.
b. Make sure that the power cord is plugged in. If the power cord is plugged in, unplug it, wait for
five minutes, and then plug it back in.
c. If the vibration platform still will not run, please see the back cover of this manual.
17
Note: Specifications are subject to change without notice. See the back cover of this manual for information about
ordering replacement parts. *These parts are not illustrated. If a part is missing, call 1-888-533-t333.
18
27
27
45
26 _52
42
23
40
28
38
38
30
28
43
54
25 17
19
For the replacement parts, accessories, and user's manuals that you need to do-it-yourself.
1-800-4-MY-HOME _ (1-800-469-4663)
Call anytime, day or night (U.S.A. and Canada)
www.sears.com www.sears,ea
Our Home
For repair of carry-in items like vacuums, lawn equipment,
and electronics, call or go on-line for the location of your nearest
Sears Parts & Repair Center.
Sears
(_) Registered Trademark / T_ Trademark / SM Service Mark of Sears Brands LLC
,_) Marca Registrada / 1M Marca de Fabrica / sf4 Marca de Servicio de Sears Brands, LLC
this Sears Vibration Platform fails due to a defect in material or workmanship within 90 days of the
date of purchase, call !-800-4-MY-HOME ¢' (!-800-469-4663) to arrange for free repair (or replacement
if repair proves impossible). There is a five year warranty on the frame.
This warranty does not apply when the Vibration Platform is used commercially or for rental purposes.
This warranty gives you specific legal rights, and you may also have other rights which vary from state
to state.
Part No. 264767 R0408A Printed in China © 2008 ICON IP, Inc.