Professional Documents
Culture Documents
PQ26 Rapid (NH-16+) New en
PQ26 Rapid (NH-16+) New en
PQ26 Rapid (NH-16+) New en
02 31-10-2020
The author is not responsible for possible side effects associated with the application of these settings on
your machine. Information is provided “as is”. All changes are made at your own risk. Most of the coding was
tested on Skoda Rapid 16 and 17 MG. If the item is marked as "must be checked", it means that more than
one successful use of the encoding is not known. Encodings for cars 19 mg. and older are marked for 19 mg.
If the coding is suitable only for machines 19 MG, this is indicated in the name of the setting.
Turn off the license plate light when opening the trunk 7
Distributed as is. You assume the entire risk of using this file.
Turning on the rear dimensions in the DRL mode (without number illumination and tidy)
eight
Stroboscope: PTF - High beam (limiting the number of working head light devices to 2)
nine
Smooth activation of the button illumination when the light is turned on eleven
Memorizing the position of the automatic high beam after muffling the car
eleven
Turning on the DRL in the side light mode (the light switch is in the side lights position, when the
headlights are turned on, the DRL are turned off) 12
DRL dimming when turning on the direction indicators on the side of the working turn signal
12
Fading of the front dimensions on the side of the working direction indicator 12
US-Standlicht nur bei Standlicht (side lights through direction indicators are full only in the position
of the light switch - side lights)
13
Damping of the front dimensions when the low / high beam headlights are turned on 13
Increase the brightness of the low and high beam lamps fourteen
Winking reversing lamps with turn signals when turning on the reverse speed and alarm
fourteen
Distributed as is. You assume the entire risk of using this file.
Increasing the interval and time of operation of the headlight washers sixteen
Remembering the last state of the recirculation of the climate control eighteen
Remembering the last recirculation state of the stove without climate eighteen
Section 5. DOORS, GLASSES, CZ, REMOTE CONTROL AND STANDARD SIGNALS ......... 19
Switching off (sound / message) about the ignition on when opening the door 20
Turning on (sound / message) about the ignition on when opening any door
twenty
Automatic door locking / unlocking for Entry / Activ configurations without Swing /
Bolero: twenty
Automatic closing of doors at a speed of 15 km / h and opening them by removing the key.
twenty
Operation of the radio channel of the key fob when the engine is running twenty
Enabling sound confirmation of opening and closing by the standard control panel (without
standard alarm) 21
Distributed as is. You assume the entire risk of using this file.
Setting the duration of the driver's door window lifter after the ignition is turned off
22
Comfortable control of the driver's door window regulator from a standard key fob
22
Auto-closing glass of the driver's door when closing the car (19 mg.) 22
Shooters test 24
Lap timer 24
Eco-tips 25
XDS activation 28
Distributed as is. You assume the entire risk of using this file.
Changing the EUR RAPID setting (setting the driving profile) thirty
Activation of the TSC function (side slip compensation, compensation for torque differences on the
drive wheels during hard acceleration) - only for
1.4TSI thirty
Changing the screen saver display time when the radio is turned on 32
Distributed as is. You assume the entire risk of using this file.
Section 11. SECURITY CODES FOR SKODA RAPID MQB UNITS ... 44
TAIL LIGHTS: 45
FRONT OPTICS: 45
Front 46
Rear 46
Side 46
Internal 46
Lamp types 47
Distributed as is. You assume the entire risk of using this file.
Block 09 -
Closed area - enter login 31347 → Adaptation -
channel:
- Leuchte 25KZL HA60-Light_Control_HD_AB_25 → instead of "Always" select the value "Only if
closed" - save
Block 09 -
Closed area - enter login 31347 → Adaptation -
channel:
- Interior lighting-Innenlicht bei offenem Heckdeckel einschalten, change “active” to “not active”
Block 09 -
Closed area - code 31347 Adaptation -
channels:
- Leuchte4TFL LB43-Light_Function_G_4, Blinken links / rechts Hellphase
- Leuchte4TFL LB43-Dimming_GH_4, 0
- Leuchte4TFL LB43-Dimming_Direction_GH_4, minimize
For 19 MG:
- Aussenlicht_Front-Tagfahrlicht_Dauerfahrlicht_bei_Handbremse_abschalten → active
Block 09
closed area -> code 31347 Adaptation ->
channel:
- Daytime running lights-Tagfahrlicht nur in Schalterstellung AUTO, active
For 19 MG:
- Aussenlicht_Front - Tagfahrlicht nur in Schalterstellung AUTO, act.
Block 09 -
Closed area - code 31347
Distributed as is. You assume the entire risk of using this file.
Inclusion of both PTFs when engaging reverse gear (standard with the function from the factory)
- static AFS light-bei Rueckwaertsfahrt - both sides
ECE R119 - works when the steering wheel is turned and when the turn signal is turned on with a delay of 1
sec
ECE R48 - only works when you turn the steering wheel
FMVSS 517 108 - works when the steering wheel is turned and when the turn signal is turned on
Block 09 -
Closed area - code 31347 Adaptation -
channels:
- Leuchte25KZL HA60-Type_Of_Load_25 - 2 * 5W - change the value to "LED Kleinleistung ohne
Open Load Diagnose" (LED)
- Leuchte25KZL HA60-Dimming_AB_25 - 100 - change to the value "127"
Not available on Rapid. There is no channel responsible separately for the right rear PTF. There is no wire
to the lamp.
Can be powered by a wire from the left lamp.
Turning on the rear dimensions together with DRL (with illuminated numbers and tidy)
Block 09 -
Closed area - code 31347 Adaptation -
channel:
- Daytime running lights-Tagfahrlicht-Dauerfahrlicht aktiviert zusaetzlich Standlicht - active> save
For 19 MG:
- Aussenlicht_Front-Tagfahrlicht-Dauerfahrlicht aktiviert zusaetzlich Standlicht → act .
Turning on the rear dimensions in the DRL mode (without number illumination and tidy)
Distributed as is. You assume the entire risk of using this file.
Block 09 -
Closed area - code 31347 Adaptation -
channel:
- Driving light and parking light-max_scheinwerfer_2limitieren → active - save.
For 19 MG:
- Aussenlicht_Front-max_scheinwerfer_2limitieren → in _Betrieb_lassen change to act.
!!! With this coding, it is impossible to use the distant one together with foglights.
Block 09 -
Closed area - code 31347 Adaptation -
channel:
- Leuchte12NL LB40-Light_Function_G_12, with not active change to Headlamp flasher
Block 09 -
Closed area - code 31347 Adaptation -
channel:
- Leuchte6ABL LB44-Light_Function_C_6, with “not active” change to “Headlamp flasher”
Block 09 -
Closed area - enter login 31347 → Adaptation →
channels :
- Leuchte4TFL LB43-Light_Function_G_4 - Lichthupe (Headlamp flasher) *
- Leuchte4TFL LB43-Dimming_GH_4 → 0
- Leuchte4TFL LB43-Dimming_Direction_GH_4 - minimize
- Leuchte5 TFL RB6-Light_Function_G_5 - Lichthupe (Headlamp flasher) *
- Leuchte5 TFL RB6-Dimming_GH_5 - 0
- Leuchte5 TFL RB6-Dimming_Direction_GH_5 - minimize
Coming Home
- Comfort illumination-Coming Home Verbaustatus - automatic (for a car with a light sensor) or
manual (for a car without a light sensor)
- Comfort illumination-Menuesteuerung Coming Home Werkseinstellung - active
- Comfort illumination-Menueeinstellung Cominghome - 10 s (duration of the function)
- Comfort illumination-Coming Home Leuchten - Low beam (through the dipped beam headlights) or Fog
light (through the fog lights)
Distributed as is. You assume the entire risk of using this file.
For 19 MG:
Block 09
closed area - code 31347 adaptation -
channels:
- Aussenlicht_uebergreifend - Coming Home Verbaustatus - automatic (for a car with a light sensor) or
manual (for a car without a light sensor)
- Aussenlicht_uebergreifend - Menuesteuerung Coming Home Werkseinstellung - active
Block 09 -
Closed area - code 31347 adaptation -
channel:
- Aussenlicht_Blinker-Komfortblinken_Blinkzyklen - select a value from 1 to 5 (from the factory by default - 3)
Distributed as is. You assume the entire risk of using this file.
Block 09 -
Closed area - code 31347 adaptation -
channel:
- Suchbeleuchtung_allgemein-KL58 Einschalten mit Rampe, active
Memorizing the position of the automatic high beam after muffling the car
Block 09 -
Closed area - code 31347 adaptation -
channels:
Assistance light functions-Fernlichtassistent Reset, not active
Block 09 -
Closed area - code 31347 - Adaptation -
channels:
- Driving light and parking light-Parklicht ueber LSS aktiviert, One-sided
Possible modes:
One-sided - one-sided inclusion (on the starboard or port side)
USA, Canada - regardless of the side of the parking lights mode, the lamps are lit on both sides.
Distributed as is. You assume the entire risk of using this file.
Block 09 -
Closed area - enter login 31347 → Adaptation -
channels:
- Leuchte4TFL LB43-Light_Function_C_4 → Abblendlicht links
- Leuchte4TFL LB43-Dimming_CD_4 → 127
- Leuchte5 TFL RB6-Light_Function_C_5 → Abblendlicht rechts
- Leuchte5 TFL RB6-Dimming_CD_5 → 127
Turning on the DRL in the side light mode (the light switch is in the side lights position, when the headlights are
turned on, the DRL are turned off)
Block 09 -
Closed area - enter login 31347 → Adaptation →
channel :
- Daytime running lights-Standlicht aktiviert zusaetzlich Tagfahrlicht → active
For 19 MG:
- Aussenlicht_Front - Standlicht aktiviert zusaetzlich Tagfahrlicht → act .
DRL dimming when turning on the direction indicators on the side of the working turn signal
Block 09 -
Closed area - enter login 31347 → Adaptation →
channels :
- Leuchte4TFL LB43-Light_Function_G_4 → Blinken links Rampe
- Leuchte4TFL LB43-Dimming_GH_4 → 0 (or another value in%)
- Leuchte4TFL LB43-Dimming_Direction_GH_4 → minimize
- Leuchte5 TFL RB6-Light_Function_G_5 → Blinken rechts Rampe
- Leuchte5 TFL RB6-Dimming_GH_5 → 0 (or another value in%)
- Leuchte5 TFL RB6-Dimming_Direction_GH_5 → minimize
Block 09 -
Closed area - enter login 31347 → Adaptation →
channels :
- Leuchte 4TFL LB43-Lichtfunktion G 4 → Blinken links Dunkelpase
- Leuchte 4TFL LB43-Dimmwert GH 4 → 0
- Leuchte 4TFL LB43-Dimming Direction GH 4 → minimize
- Leuchte 5TFL RB6-Lichtfunktion G 5 → Blinken rechts Dunkelpase
- Leuchte 5TFL RB6-Dimmwert GH 5 → 0
- Leuchte 5TFL RB6-Dimming Direction GH 5 → minimize
Block 09 -
Closed area - enter login 31347 → Adaptation →
channels :
- Leuchte2SL VLB22-Light_Function_E_2 → Blinken links Rampe
- Leuchte2SL VLB22-Dimming_EF_2 → 0 (or another value in%)
- Leuchte2SL VLB22-Dimming_Direction_EF_2 → minimize
- Leuchte3SL VRB36-Light_Function_E_3 → Blinken rechts Rampe
- Leuchte3SL VRB36-Dimming_EF_3 → 0 (or another value in%)
- Leuchte3SL VRB36-Dimming_Direction_EF_3 → minimize
Distributed as is. You assume the entire risk of using this file.
Block 09 -
Closed area - enter login 31347 → Adaptation →
channels :
- Leuchte 0 BLK VL B35-Light_Function_C_0 → Standlicht
- Leuchte 0 BLK VL B35-Dimming_CD_0 → 35
- Leuchte 0 BLK VL B35-Dimming_Direction_CD_0 → maximize
- Leuchte 0 BLK VL B35-Light_Function_E_0 → Blinken links Dunkelpase
- Leuchte 0 BLK VL B35-Dimming_EF_0 → 0
- Leuchte 0 BLK VL B35-Dimming_Direction_EF_0 → minimize
US-Standlicht nur bei Standlicht (side lights through direction indicators are full only in the position of the
light switch - side lights)
Block 09 -
Closed area - enter login 31347 → Adaptation →
channels :
- Leuchte 0 BLK VL B35-Light_Function_A_0 → Standlicht Vorn
- Leuchte 0 BLK VL B35-Dimming_AB_0 → 35
- Leuchte 0 BLK VL B35-Light_Function_C_0 → Abblendlicht links
- Leuchte 0 BLK VL B35-Light_Function_D_0 → Blinken links Dunkelpase
- Leuchte 0 BLK VL B35-Dimming_CD_0 → 0
- Leuchte 0 BLK VL B35-Dimming_Direction_CD_0 → minimize
- Leuchte 0 BLK VL B35-Light_Function_E_0 → Blinken links Hellphase
- Leuchte 0 BLK VL B35-Dimming_EF_0 → 100
- Leuchte 0 BLK VL B35-Dimming_Direction_EF_0 → maximize
Damping of the front dimensions when the low / high beam headlights are turned on
Block 09 -
Closed area - enter login 31347 → Adaptation →
channels :
- Leuchte2SL VLB22-Light_Function_A_2 → Standlicht - change to Standlicht vorn
- Leuchte3SL VRB36-Light_Function_A_3 → Standlicht - change to Standlicht vorn
Block 09 -
Closed area - enter login 31347 Adaptation - channels:
Option A
(while winking on one side - on the other side, the clearance is canceled)
Distributed as is. You assume the entire risk of using this file.
Option B
(while winking on one side - on the other side the marker is on)
- Leuchte2SL VLB22-Light_Function_E_2 → Blinken links Dunkelpase
- Leuchte2SL VLB22-Light_Function_F_2 → Blinken rechts aktiv
- Leuchte2SL VLB22-Dimming_EF_2 → 100
- Leuchte2SL VLB22-Dimming_Direction_EF_2 → maximize
- Leuchte3SL VRB36-Light_Function_E_3 → Blinken rechts Dunkelpase
- Leuchte3SL VRB36-Light_Function_F_3 → Blinken links aktiv
- Leuchte3SL VRB36-Dimming_EF_3 → 100
- Leuchte3SL VRB36-Dimming_Direction_EF_3 → maximize
* Works only in conjunction with the item "Blanking the front dimensions when turning on the
low / high beam headlights"
Block 09 -
Closed area - enter login 31347 Adaptation - channels:
Block 09 -
Closed area - enter login 31347 Adaptation - channels:
Block 09 -
Closed area - enter login 31347 Adaptation - channels:
It should be understood that these operations will result in reduced lamp life. An example of a reduction
in service life is shown in the table below.
Winking reversing lamps with turn signals when turning on the reverse speed and alarm
Block 09 -
Closed area - enter login 31347 -
Distributed as is. You assume the entire risk of using this file.
Block 09 -
Closed area - code 31347 Adaptation -
channels:
Leuchte20BR LA70-L Light_Function_C_20, Tuerausstiegslichtv links (with the door open on the left
side).
Leuchte20BR LA70-Dimming_CD20, 100
Leuchte20BR LA70-Dimming_Direction_CD20, maximize
Block 09 -
Closed area - code 31347 - Adaptation -
channels:
- Leuchte16BLK SLC11-Light_Function_C_16 → Rear lid open
- Leuchte16BLK SLC11-Dimming_CD_16 → 50
- Leuchte17 BLK SR A72-Light_Function_C_17 → Rear lid open
- Leuchte17 BLK SR A72-Dimming_CD_17 → 50
Distributed as is. You assume the entire risk of using this file.
Block 09 -
Closed area - code 31347 Adaptation -
channel:
- Windshield wiper-Menuesteuerung Frontwischer - active - save.
Solves the problem with the wipers stopping half way in the middle of the glass when the ignition is
turned off.
Block 09 -
Closed area - code 31347 Adaptation -
channel:
- Windshield wiper-Wischer stop bei KL15 aus, change active to not active - save.
active - wipers get up in any position when the ignition is turned off; not active - the wipers are
parked.
Rubbing drops
Additional cleaning 5 seconds after the last washing and cleaning process (only at speeds> 5 km / h).
Does not work at subzero temperatures.
Block 09 -
Closed area - code 31347 Adaptation -
channel:
Front wiper:
- Windshield wiper-Traenenwischen Front Status - active - save.
Rear wiper:
- Rear Window Wiper-Traenenwischen Heck - active - save.
Block 09 -
Closed area - code 31347 Adaptation -
channel:
- Assistance light functions-Lichtsensorempfindlichkeit, normal change the value to "non sensitive" - save.
Block 09 -
Closed area - code 31347 Adaptation -
channel:
- Windshield wiper-SRA Waschzeit, 2300 ms - replace with 0 - save.
Block 09 -
Closed area - code 31347 Adaptation -
channel:
- Windshield wiper-Anzahl Betaetigungen Frontwaschanlage pro SRA Aktivierung → enter "15" → save
Distributed as is. You assume the entire risk of using this file.
Block 09 -
Closed area - code 31347 Adaptation -
channel:
- Rear Window Wiper-Comfortwischen Heck, not active or via the
radio menu
The rear wiper starts to operate when the front wipers are continuously running at 2 speeds.
Block 09 -
Closed area - code 31347 Adaptation -
channel:
- Rear Window Wiper-Automatisches Heckwischen, active
Block 09 -
Closed area - code 31347 Adaptation -
channel:
- Windshield wiper-Frontwischer Abtauposition, Abtauposition
temperaturunabhaengig Referenzwischen
keine Abtauposition - do not move the wipers to the defrost position (default);
Abtauposition temperaturunabhaengig Referenzwischen - raise the wipers to the defrost position regardless
of the ambient temperature, manual wipers operation
Block 09 -
Closed area - code 31347 Adaptation -
channel:
- Windshield wiper- Wischer Stopp bei Oeffnen der Motorhaube, active
It is also possible to turn on the parking of the wiper when opening the hood, but you need to be careful with
this mode. If the wipers were in the service position and were tilted away from the windshield, they will go to
the parking lot, and the hood edge may be damaged:
Distributed as is. You assume the entire risk of using this file.
Block 09 -
Closed area - code 31347 Adaptation -
channel:
- Window heater-Heckscheibenheizung Zeitwert, value 600 s (10 min) - change to 1200 s (20 min) - save.
Block 08 -
Basic parameters 04 - Group 1 -
read.
After the group has been read, numbers will appear in the empty fields and after that we press the on /
off / next button and the adaptation process begins. THIS IS NOT NECESSARY TO DO ANYTHING WITH
THE MACHINE. After the end of adaptation, the message ENDANSCHLAEGE LERNEN will be displayed.
The flap adaptation process is now complete.
Distributed as is. You assume the entire risk of using this file.
Distributed as is. You assume the entire risk of using this file.
Turning on (sound / message) about the ignition on when opening any door
Automatic door locking / unlocking for Entry / Activ configurations without Swing / Bolero:
Block 09 -
Closed area - enter the code 31347. Adaptation -
channels:
- Access control-automatisches Verriegeln bei Geschwindigkeit - active
- Access control-automatisches Entriegeln - active
- Access control-Autolock Autounlock wirkt auf Heck - active
For 19 MG:
- ZV Autolock-Autolock_Autounlock_wirkt_auf_Heck → act .
- ZV Autolock-automatisches_Entriegeln → - act.
- ZV Autolock-Automatisches_Verriegeln_bei_Geschwindigkeit → act .
Automatic closing of doors at a speed of 15 km / h and opening them by removing the key.
Block 09 -
Closed area - enter the code 31347. Adaptation -
channel:
- Access control-automatisches Verriegeln bei Geschwindigkeit –active
- Access control-automatisches Entriegeln - active
- Access control-ZV Türentriegelung - was Clobal Entriegelung (all doors at once), set the desired one
(Einzeltuerentriegelung - the driver's door opens separately, seitenselektive Oeffnung - all doors on one
side, individuell selective Oeffnung Kessy - separate opening when using the keyless entry system)
Operation of the radio channel of the key fob when the engine is running
Block 09 -
Closed area - code 31347. Adaptation -
channel:
- Access control-Funk bei Klemme 15 ein, active.
For 19 MG:
- ZV allgemein-Funk bei Klemme 15 ein, active.
Block 09 -
Closed area - code 31347. Adaptation -
channel:
- Auxiliary functions-Signalhorn ohne KL15, active
Block 09 -
Distributed as is. You assume the entire risk of using this file.
Adaptation - channel:
- Access control -Akustischer Alarm Signalhorn change from "not act." to "act." It will be triggered when the
door is opened with a key after closing the car with a standard key fob.
To use, you need to re-read the block settings from memory (arm / disarm the car for
5-10 seconds)
Enabling sound confirmation of opening and closing by the standard control panel (without standard
alarm)
Block 09
closed area - code 31347 adaptation -
channels:
- Anti-theft device-Akustischer_Alarm_Signalhorn → act .
- Anti-theft device-anti_theft_alarm_system → act .
- Anti-theft device-Alarmsignal → frequency modulated
- Anti-theft device-Sirenen_Alarmzahl → 10 Alarme
Block 09 -
Closed area - code 31347. Adaptation -
channel:
- Access control 2-Freigabenachlauf FH bei Kl 15 aus, not active, set active - save.
Distributed as is. You assume the entire risk of using this file.
Setting the duration of the driver's door window lifter after the ignition is turned off
Block 09 -
Closed area - code 31347. Adaptation -
channel:
- Access control 2-FH SAD Kl15Aus Freigabezeit - 600 s (10 minutes after turning off the
ignition) - save.
For 19 MG:
- ZV Komfort (Fensterheber) -FH SAD Kl15Aus Freigabezeit - 600 s
Block 09 -
Closed area - code 31347. Adaptation -
channel:
- Access control 2-Freigabenachlauf FH bei Tueroeffnen, not active, set to active - save.
For 19 MG:
- ZV Komfort (Fensterheber) -Freigabenachlauf FH bei Tueroeffnen → active
Comfortable control of the driver's door window regulator from a standard key fob
Block 09 -
Closed area - code 31347. Adaptation -
channel:
- Access control 2-Comfort closing - active
- Access control 2-Comfort opening - active
- Access control 2-Fahrertuerbedienung Fensterheber oeffnen - active
- Access control 2-Fahrertuerbedienung Fensterheber schliessen - active
- Access control 2-Funk Comfort oeffnen - active
- Access control 2-Funk Komfort schliessen - active
- Access control 2-Komfortbedienung global - active
- Access control 2-Menuesteuerung Komfortbedienung einstellbar → adjustable
Next, you need to enable the appropriate option in the radio menu that appears.
Who has a simple blues radio tape recorder enough to activate: Block 09 -
Auto-closing glass of the driver's door when closing the car (19 mg.)
Block 09 -
closed area - code 31347 - adaptation -
channels:
- ZV Comfort (Fensterheber) - Comfort closing → act .
- ZV Comfort (Fensterheber) - Comfort opening → not active .
Distributed as is. You assume the entire risk of using this file.
Distributed as is. You assume the entire risk of using this file.
Shooters test
Lap timer
Block 09 -
Closed area - code 31347 Adaptation -
channel:
- Driving light and parking light-Nebelschlusslicht Warngeschwindigkeit 0 - warning disabled.
But the mileage begins to deviate significantly from the real one. A value of 03 increases the mileage by
approximately 300 meters per 10 km. With factory coding 00, the magnification is 200 meters by 40 km.
- SIE: time from inspection - instead of mileage in days, set the value to 0
- SIE: distance from inspection - instead of mileage in km, set the value to 0
- ESI: Resetting ESI - select Reset.
Distributed as is. You assume the entire risk of using this file.
- ESI: maximum value km-driving distance / inspection, 30,000 km - change to the desired one, for
example 15,000
- ESI: minimum value km-driving distance / inspection, 15000 km - change to the desired one, for
example 7500
- ESI: maximum value of time between inspections, 730 d - change to the desired one
- ESI: minimum value of time between inspections, 365 d - change to the desired one
Eco-tips
Block 19 -
Encoding - Long encoding - 13 bytes - bit 0 - incl.
In the adaptations of block 19, at your discretion, disable unnecessary items (by default, all are
activated from the factory):
- Demonstration of the efficiency program-Council - brake. engine: out. clutch only at rev. less than 1300.
- Efficiency Program Display - Tip - Do not press the accelerator pedal when starting the engine.
Go to the settings menu of the displayed information of the panel in the radio and turn on the "Eco-tips"
item.
- Display correction of consumptions and operating range, 100% Default - 100%, step
1%, minimum - 85%, maximum - 115%
Conversion example:
We take the consumption of the on-board computer displayed on the panel - 6.3 liters per 100 km.
Distributed as is. You assume the entire risk of using this file.
Next, we calculate the proportions. We take the readings of the on-board computer for 100%
6.3 - 100%
6.8 - X
It works on the principle of a hysteresis loop: we trigger at the lower level, turn off at the upper
level.
Block 17 -
Closed area - code 47115 (for old 20103) Adaptation - channel:
Block 17 -
Adaptation - channel:
- Illumination_algorithm-Scale_switching_algorithm, change “parking_light” to “lds”
Distributed as is. You assume the entire risk of using this file.
Block 03 -
Closed area - code 40168 Adaptation -
channel:
- Starting vibration reduction> select the desired value (Strong, Normal, Maximum)> save.
* For winter conditions, the preferred value of Maximum - excludes slipping at the start.
Block 03 -
Long coding -
16 bytes - bit 0 - enable
To use, you need to re-read the block settings from memory (arm / disarm the car for
5-10 seconds)
Block 03 -
Closed area - code 40168 Adaptation -
channel:
- Berganfahrassistent - select the desired value (early, normal, at the end) - save.
There are 3 levels of meaning: schwach (1-weak), stark (3-strong), mittel (2 medium)
Block 03 -
Closed area - code 40168 Adaptation -
channel:
- Brake disk drying - select Stufe 2 (mittel) (or select the desired value) - save.
Block 03 -
Closed area - code 40168 Adaptation -
channel:
- Hydraulic brake assistant - select normal (or select the desired value) - save.
Block 03 -
Closed area - code 40168 Adaptation -
channel:
- Overboost in brake system - default value 6 - (select the desired value) - save.
Block 03 -
Closed area - code 40168 Long coding -
Distributed as is. You assume the entire risk of using this file.
XDS activation
NOT POSSIBLE! TRW (Electronic Brake Control - EBC 460) ESC / ABS units do not support this functionality.
SW: 6R0 614 517 BQ, 6R0 614 517 CA or 6R0 614 517 CG
Block 03 -
Closed area - code 40168 Encoding - Long
encoding - Byte 17 - bits 0-3
01 - 1.6MPI / 66 kW / 90 hp / 155 nm
02 - 1.6MPI / 81 kW / 110 hp / 155 nm with manual transmission 03
- 1.6MPI / 81 kW / 110 hp / 155 nm with automatic transmission
04 - 1.0TSI / 70 kW / 95 HP / 160 nm and 1.2TSI / 66 kW / 90 HP / 160 nm 05 - 1.2TSI / 81 kW
/ 110 HP / 175 nm and 1.0TSI / 81 kW / 110 hp / 200 nm 06 - 1.4TSI / 92 kW / 125 hp / 200
nm with DSG
07 - 1.4TDI / 66 kW / 90 hp / 230 nm with manual
transmission 08 - 1.4TDI / 66 kW / 90 hp / 230 nm with
DSG 09 - 1.6TDI / 85 kW / 115 hp / 250 nm
Block 5F -
Closed area - code 20103 Adaptation -
channel:
- Car_Function_List_BAP_Gen2-tire_pressure_system_0x07, change from "not activated" , to
"activated."
- Car_Function_List_BAP_Gen2-tire_pressure_system_0x07_msg_bus, change from, "Drive data bus", to,
"Comfort data bus"
- Car_Function_Adaptations_Gen2-menu_display_rdk, change from "not activated" to "activated".
Block 17 (5JA-920-7XX) -
Coding - Long coding - Byte 04 - bit 0 - activate
Distributed as is. You assume the entire risk of using this file.
- tire pressure monitoring system, tire selection - select the value "normal", "unknown" or "SST tires"
Distributed as is. You assume the entire risk of using this file.
010100000C000000000000000000000000000000.
Other options for encoding such BU are also possible:
- 010200000C000000000000000000000000000000 - for dv. 1.4TFSI and 1.8TFSI
- 010500000C000000000000000000000000000000 - for 1.6 CPDA engines. Accordingly, with a 20-byte
encoding, 010100000C0 ... to the end of zeros, change the first 7 digits - for example, to 00000080C ... to
the end of zeros (Audi A3) - save!
Block 01 -
Encoding - Long encoding -
Byte 00 - bits 0-2 - select the value 02 (Manufacturer: Audi) - execute.
* not recommended for cars with cruise control - there will be cruise glitches
Block 44 -
Closed area - code 17580 Long coding -
byte 00 - bit 7 - enable. The value changes from 00 to 80. Save the encoding.
Adaptation - channels:
- Characteristic curve of steering assistance → select the desired value (Driving profile selection button,
Comfort, Automatic, Dynamic, Default) → save .
Activation of the TSC function (side slip compensation, compensation for torque difference on the driving wheels
during hard acceleration) - only for 1.4TSI
Block 44 -
Distributed as is. You assume the entire risk of using this file.
Block 19 -
Closed area - code 20103 Adaptation -
channels:
- EM_start_stop_requirement_ambient_temperature-Minimum_temperature, -50.0 ° C, change the value to
50.
Or by voltage:
- Start Stop voltage limit - 7.6V change to 12.1V
Description - open the car. When the ignition is off, the button pulsates, when it is on, too. On the
wound it just burns.
Block 05
Access code: 20103
Adaptation:
Channels: ENG123036-ENG120038-DeveloperCoding: Search lights-ZAT detecting open load :, activate
Distributed as is. You assume the entire risk of using this file.
Block 5F -
Long coding -
Byte 11 - bit 2 (Skoda Surround and Virtual Subwoofer items are added) Byte 08 - bit 6 - VDA Low
Frequency Input enable
Block 5F -
Long coding -
Byte 18 - change the value 00 to the preferred 01-vRS
02-SCOUT
03-Laurin & Klement
04-GreenLine
07-MonteCarlo (for swing 2 and 3)
08-SportLine (only for swing 3))
After saving the encoding, it is necessary to apply the new value by rebooting the radio (on swing - by
holding the power button for a long time). The next time the radio is turned on for the first time (after
removing from the signaling), we observe a new splash screen.
Block 5F -
Closed area - code 20103 Long coding -
Block 5F -
Coding - Long Coding - Byte 01 - Bits 0 ~ 23:
Changing the screen saver display time when the radio is turned on
Block 5F -
Closed area - code 20103 Adaptation -
channel:
- Time display for start screen, 2.0 s - set the desired
Block 5F -
Encoding - Long encoding - Byte 04 - bits 0 ~ 31 -
selectable
Distributed as is. You assume the entire risk of using this file.
Block 5F -
Encoding - Long encoding - Byte 8 - bit 4 - enable
Block 5F -
Encoding - Long encoding - Byte 19 - bits 6 ~ 7 - select
value
- 80 (USB functionality) or
- С0 (USB and iPhone functionality).
Block 5F -
Closed area - code 20103 Adaptation -
channel:
- Microphone sensitivity, 0 dB - set the required value.
A negative value set in this parameter will increase the volume of the microphone signal. The smaller the
negative value, the greater the gain.
Block 5F -
Closed area - code 20103 Adaptation -
channel:
- Car_Function_Adaptations_Gen2-menu_display_board_computer_clamp_15_off, switch from not
activated, to activated
Block 5F -
Adaptation - channel:
- Car_Function_Adaptations_Gen2-menu_display_driving_school, switch from not activated to activated
- Car_Function_Adaptations_Gen2-
menu_display_driving_school_over_threshold_high, switch from not activated to activated
Block 5F -
Adaptation - channel:
Car_Function_Adaptations_Gen2-menu_display_compass_clamp_15_off: activated.
Car_Function_Adaptations_Gen2-menu_display_compass_over_threshold_high: activated.
Car_Function_Adaptations_Gen2-menu_display_compass: activated.
Distributed as is. You assume the entire risk of using this file.
The engineering menu is launched by holding the Setup button for a long time until the menu: Engineering
Testmode appears on the screen.
We select: Software System - Audio Management → in the
Loudness item put a tick
then select: Input Gain Offset and in the points below we increase the level by 13 dB
→ FM source - +12
→ Media File Player - +9
→ BT audio - +13
We exit the Engineering menu and adjust the balance and equalizer in the sound settings, if
necessary.
After completing all sound settings, it is advisable to deactivate the Engineering menu. It is believed
that when activated, it discharges the battery.
Distributed as is. You assume the entire risk of using this file.
Block 09 -
Closed area - code 31347 Coding - long coding -
Byte 06 - bits 0-1 select 02 Light sensor installed [PR-8K3 / 8K9 + 8N6] Byte 06 - bit 3 - enable
Byte 07 - bits 0-1 select 03 Coming / Leaving function type: Seat / Skoda /
Volkswagen
Byte 07 - bit 5 - enable Byte 13 - bit 5
- enable
Block 09 -
Closed area-code 31347
Coding -
in the list of devices, select 5Q0 955 547B light / rain sensor (RLHS) - Long coding -
Byte 0 - 00
Bytes 1-2 - choose 185E or 984D (for cars with heated windshield) As a result, the encoding takes on the
value - 00 18 5E
Block 09 -
Closed area-code 31347
Adaptation - channels:
- Assistance light functions-Assistenzfahrlicht bei Regen - active
- Assistance light functions-AFL Zeitverzoegerung - 2,000 ms
- Assistance light functions-Lichtsensorempfindlichkeit - normal
- Assistance light functions-Assistance_lighting_sensitivity_ajustable - present
Corner adaptation with support for Coming Home / Leaving Home functions via PTF
Distributed as is. You assume the entire risk of using this file.
2. In adaptation, activate Corner with Coming Home / Leaving Home functions via PTF
For 19 MG:
1) Block 09 - closed area - code 31347 - adaptation - channels:
- Auxiliary light functions-Rain / light sensor → Rain / light sensor
- Auxiliary lighting functions -Humidity sensor → set
- Auxiliary lighting functions -Will Beam assistant: responsivity adjustable via BAP → available
Byte 0 - 00
Bytes 1-2 - choose 185E (984D) or
- Aussenlicht_uebergreifend-Menueeinstellung Cominghome - 10 s
- Aussenlicht_uebergreifend-Coming Home Leuchten - Low beam
- Aussenlicht_uebergreifend-Coming-home Einschaltereignis - Driver door
- Aussenlicht_uebergreifend-Helligkeitsschwelle Infrarot-Messung - 72.0
- Aussenlicht_uebergreifend-Leaving-Home Verbausstatus - allowed
- Aussenlicht_uebergreifend-lho_aktiviert - act.
- Aussenlicht_uebergreifend-lho_zeit - 10 s
- Aussenlicht_uebergreifend-Helligkeitsschwelle Forward-Messung - 100
- Aussenlicht_uebergreifend-Menueeinstellung CHO LHO - Menuesteuerung Zeit aktivieren
- Aussenlicht_uebergreifend-
Lichtdrehschalter_mit_Nebellicht_bei_Assistenzfahrlicht - Yes
- Windshield wiper - Regensensor aktivieren - act.
Block 09 -
Closed area - code 31347 Coding - long coding -
Distributed as is. You assume the entire risk of using this file.
Adaptations:
Leuchte 0 BLK VL B35 - it is the left front turn signal [LO] _Dimming_AB_0 - 128
Leuchte 1 BLK VR B23 - it is the right front turn signal [LO] _Dimming_AB_1 -
128
[LO] _Light_Function_A_1 - Blinken rechts Hellphase [LO]
_Type_Of_Load_1 - LED Blinkleuchten
Distributed as is. You assume the entire risk of using this file.
For 19 MG:
Block 09 - closed area - code 31347 - adaptation - channels:
- Aussenlicht_Front-Low beam: bulb type → HID
Distributed as is. You assume the entire risk of using this file.
Distributed as is. You assume the entire risk of using this file.
(1) -Leuchte23SL HLC7-Type_Of_Load_23 → Allgemeine LED mit Open Load Diagnose (6) -Leuchte23SL
HLC7-Dimming_AB_23 → 100
(1) -Leuchte24SL HRA69-Type_Of_Load_24 → Allgemeine LED mit Open Load Diagnose (6) -Leuchte24SL
HRA69-Dimming_AB_24 → 100
Block 19 block -
Adaptation - channels:
Battery Adaption - Battery capacity - enter the desired value: 61Ah 300A (DIN) or 540 (EN)
Realization on one free circuit, through connection to the T46b / 45 output. Pin number - А 018 545
8626
Center console compartment light - 7P6 919 390 A KT1 Connector housing - 8K0 973 754
Block 09 -
Closed area - code 31347 Encoding - long
encoding - Byte 17 - bit 0 - enable.
Distributed as is. You assume the entire risk of using this file.
Block 01 -
Encoding - long encoding - Byte 6 - bit 2 - enable.
Block 09 -
Closed area - code 31347 Encoding - long
encoding - Byte 18 - bit 7 - enable.
Rear view camera 5JA827566. Installation is available on Swing (5JA035871D), Bolero (5Q0035840B).
The video cable is connected to the radio tape recorder to the CVBS + and CVBS- connectors.
Block 5F
Coding - Long coding - Byte 19 - bit 4 - enable.
Distributed as is. You assume the entire risk of using this file.
Connection in the area of the fuse box. Minus - to the bolt. Plus - to a free fuse (it can be
permanently connected, it is possible to work with the ignition on).
Block 09 -
closed area - code 31347 - adaptation -
channels:
- Aesthetic lighting-Ambience_borders_front → installed .
- Leuchte32AMBL 2C64-Dimming_AB_32 → 100
- Leuchte32AMBL 2C64-Fehlerort_mittleres_Byte_DTC-DFCC_32 → 03
- Leuchte32AMBL 2C64-Light_Control_HD_AB_32 → Always
- Leuchte32AMBL 2C64-Light_Function_A_32 → Ambientelicht 1
- Leuchte32AMBL 2C64-Type_Of_Load_32 → LED Kleinleistung ohne Open Load Diagnose
Check it out!
Block 09 -
Encoding - Long encoding -
Byte 02 - Bits 0 ~ 2 - 01 Illumination: Halogen Headlights with High Beam Assist [PR-8ID + 8G1]
Block 20 (8X0-857-511.lbl) -
Coding - Long coding - Byte 00 - bits 0-4 -
01 headlights type: halogen 02
headlights type: bi-xenon
Byte 01 - Bits 0-1 - Byte 02 - 01 control: left hand drive
Bits 0-7 - Byte 03 - Bits 0-7 - 8f vertical displacement Skoda Octavia (5E)
Byte 04 - Bits 0-7 - Byte 05 - 6b correction (red) bi-xenon Skoda Octavia (5E) 76 correction (red)
Bits 0-7 - Byte 06 - Bits 0-7 - halogen Skoda Octavia (5E)
Byte 07 - Bits 0-7 - Byte 08 - 76 correction (red) rear lights Skoda Octavia (5E) 5D correction (blue) bi-xenon
Bits 0-7 - Byte 09 - Bits 0-7 - Skoda Octavia (5E) 52 correction (blue) halogen Skoda Octavia (5E)
Byte 10 - Bits 0-7 - Byte 11 -
Bits 0-7 - Byte 12 - Bits 0-7 - 52 correction (red) rear lights Skoda Octavia (5E) 20 correction (UCR) bi-xenon
Skoda Octavia (5E) 34 correction (UCR) halogen Skoda Octavia (5E)
Block 09 -
Adaptation - channel:
- Assistance light functions-Menuesteuerung Fernlichtassistent, adjustable
- Assistance light functions-Menuesteuerung Fernlichtassistent Werkseinstellung,
adjustable
Distributed as is. You assume the entire risk of using this file.
Distributed as is. You assume the entire risk of using this file.
Block 01 - 27971
Block 03 - 40168 + 20103 (40304), 15081 ??? Block 08
Block 18 - 80782
Block 19 - 20103
Block 20 - 89687
Block 44 - 17580 (19249) Block 5F
- 20103
Block 75 - 20103
Block A5 - 20103
Distributed as is. You assume the entire risk of using this file.
FRONT OPTICS:
Block 09
Closed area - 31347 Adaptation:
Distributed as is. You assume the entire risk of using this file.
Rear
Leuchte20BR LA70 - left rear stop Leuchte21BR RC8 -
right rear stop Leuchte22BR MC9 - additional stop
Leuchte25KZL HA60 - number light Leuchte28RFL C3
- reverse
Side
Leuchte16BLK SLC11 - left side turn signal Leuchte17 BLK SR A72 -
right side turn signal
Internal
Parklicht links (beidseitiges Parklicht aktiviert li & re) - Parking light - parking lights
Parklicht links - Parking light links - Left parking lights Parklicht rechts - Parking light right -
Right parking lights
Distributed as is. You assume the entire risk of using this file.
Tagfahrlicht - DRL
Daytime running lights - DRL
Blinken links Hellphase - when the left turn signal lights up Blinken links Dunkelphase -
when the left turn signal goes out Blinken rechts Hellphase - when the right turn signal
lights up Blinken rechts Dunkelphase - when the right turn signal goes out
Blinken links aktiv (beide Phase) - constantly when the left turn signal is working Blinken rechts aktiv (beide
Phase) - constantly when the right turn signal is working
Dimmung klemme 58xs - dimming with a dimmer from the passenger compartment
Terminal 58xs dimmer
Innenlicht - smoothly incl. at open. doors
Kofferraumlicht - lights up when you turn on the light in the trunk (when open) Fussraumlicht
- lights up (not smoothly) when you open the rear left. doors
Tuerausstiegslicht hinten rechts - rear right door Tuerausstiegslicht vorn links - front
left door Tuerausstiegslicht vorn rechts - front right door Tuerausstiegslichtv links -
when opening the door on the left side of Tuerausstiegslichtv
Lamp types
Distributed as is. You assume the entire risk of using this file.
Distributed as is. You assume the entire risk of using this file.
Front
Distributed as is. You assume the entire risk of using this file.
Distributed as is. You assume the entire risk of using this file.
Distributed as is. You assume the entire risk of using this file.
Distributed as is. You assume the entire risk of using this file.
Additional stop
Distributed as is. You assume the entire risk of using this file.
Distributed as is. You assume the entire risk of using this file.
Distributed as is. You assume the entire risk of using this file.
Distributed as is. You assume the entire risk of using this file.
Distributed as is. You assume the entire risk of using this file.
Salon light
Distributed as is. You assume the entire risk of using this file.
ENG105831-ENG101574-dimming_characteristic_curve_adjustment_clock_dial_day-X1,00 ...
ENG105831-ENG99777-dimming_characteristic_curve_adjustment_clock_dial_day-Y1,00 ...
ENG105832-ENG101574-dimming_characteristic_curve_adjustment_clock_dial_night-X1,00 ...
ENG105832-ENG99777-dimming_characteristic_curve_adjustment_clock_dial_night-Y1,02 ...
ENG105834-ENG101574-dimming_characteristic_curve_adjustment_gauge-X1,00 ...
ENG105834-ENG99777-dimming_characteristic_curve_adjustment_gauge-Y1,03 ...
ENG105835-ENG101574-dimming_characteristic_curve_adjustment_indicator_lights-X1,00 ...
ENG105835-ENG99777-dimming_characteristic_curve_adjustment_indicator_lights-Y1,05 ...
ENG119878-ENG101574-dimming_characteristic_curve_adjustment_internal_phototransistor-X1,00 00
...
ENG119878-ENG99777-dimming_characteristic_curve_adjustment_internal_phototransistor-Y1,00 00
...
ENG105836-ENG101574-dimming_characteristic_curve_adjustment_middle_display_main_fieldX1,00
...
ENG105836-ENG99777-dimming_characteristic_curve_adjustment_middle_display_main_field-Y1,01
...
There are many of them, 5-6 X and Y values for each position. Let's call a pair of X and Y settings a
curve. It turns out there are 6 curves:
dimming_characteristic_curve_adjustment_clock_dial_day - backlight brightness
scales for daytime.
dimming_characteristic_curve_adjustment_clock_dial_night - backlight brightness
scales for night mode.
dimming_characteristic_curve_adjustment_gauge - the brightness of the arrows backlight
appliances
dimming_characteristic_curve_adjustment_indicator_lights - brightness
additional indicators of the instrument panel
dimming_characteristic_curve_adjustment_internal_phototransistor - curve
normalization of readings of the panel light sensor.
Distributed as is. You assume the entire risk of using this file.
Day mode differs from night mode by the included dipped beam. The neighbor is on
- night mode
Let's try to adapt the values of the scale backlight brightness curves for day / night mode and the
normalization curve of the panel light sensor readings.
Distributed as is. You assume the entire risk of using this file.
dimming_characteristic_curve_adjustment_clock_dial_day, dimming_characteristic
_curve_adjustment_clock_dial_night
Curves for setting the brightness of the backlight of the scales for day and night modes. We only work with Y
values. 0 - backlight is disabled. 253 is the maximum brightness. In order not to turn off the backlighting of
the scales at dusk, you need to get rid of 0 values in the daytime backlight curve (highlighted in yellow in the
table). The values in the green columns can be adjusted as desired. For the day mode, the complete
dimming of the scales at dusk has been removed. For night mode, a curve with a dimmer glow at high sensor
readings is proposed.
dimming_characteristic_curve_adjustment_internal_phototransistor
The curve is normalizing the readings of the light sensor to an interval of 0.253. 0 - dark, 253 - maximum
light. You can sharpen the curve at the maximum value. We work only with the X coordinate.
Distributed as is. You assume the entire risk of using this file.
ENG105831-ENG99777-
dimming_characteristic_curve_adjustment_clock_dial_day-Y1.03
ENG105831-ENG100480-
dimming_characteristic_curve_adjustment_clock_dial_day-Y2.05
ENG105831-ENG100773-
dimming_characteristic_curve_adjustment_clock_dial_day-Y3.08
I do not recommend changing the direction of the brightness change, or twisting the values to the
maximum.
I did not set myself to turn off the backlight at dusk - everything suits me. The access code must
be selected. Try 47115.
Distributed as is. You assume the entire risk of using this file.
dauer - duration
Dauerfahrlicht - DRL
Defaultwert - default value Einschaltgrenze - enable limit
Einschaltereignis - trigger event Fahrt - ride, ride
Nachwischen - wipe
Nebelschlusslicht - rear fog lights Notlaufprogramm - emergency
program
Regenschliessen - rain closure Richtung - direction
Rueckmeldung - feedback
Schalterstellung - position switch Scheinwerfer - headlights
Tagfahrlicht - DRL
Tagfahrlichtkontrollleuchte - DRL work indicator Traenenwischen -
wiping drops
Vorn - ahead
Warngeschwindigkeit - warning speed Warnung - warning
Distributed as is. You assume the entire risk of using this file.
zusaetzlich - optional
Distributed as is. You assume the entire risk of using this file.
+ Comfortable control of the driver's door window regulator from a standard key fob
+ Driving School Mode on Swing / Bolero
Distributed as is. You assume the entire risk of using this file.
Distributed as is. You assume the entire risk of using this file.
Distributed as is. You assume the entire risk of using this file.
Distributed as is. You assume the entire risk of using this file.