Professional Documents
Culture Documents
Fluid Lines and Fittings Flashcards
Fluid Lines and Fittings Flashcards
com
Prep
Find over 500 million flashcards Search
8192. Which coupling nut should be selected for use with 1/2-inch aluminum
oil lines which are to be assembled using ared tube ends and standard AN
nuts, sleeves, and ttings?
C - AN-818-8
8193. Metal tubing uid lines are sized by wall thickness and
https://www.chegg.com/flashcards/fluid-lines-and-fittings-0ea86c55-1da3-4d42-81cf-8d12eb38de71/deck 1/10
3/15/2021 Fluid Lines And Fittings Flashcards | Chegg.com
Prep
8194. From the following sequences of steps, indicate the proper order you
would use to make a single are on a piece of tubing:
Place the tube in the proper size hole in the aring block.
Project the end of the tube slightly from the top of the aring tool, about the
thickness of a dime.
Slip the tting nut and sleeve on the tube.
Strike the plunger several light blows with a lightweight hammer or mallet
and turn the plunger one-half turn after each blow.
Tighten the clamp bar securely to prevent slippage.
Center the plunger or aring pin over the tube.
B - 3,1,6,2,5,4
A - By cutting out the damaged area and utilizing a swaged tube tting to join
the tube ends.
https://www.chegg.com/flashcards/fluid-lines-and-fittings-0ea86c55-1da3-4d42-81cf-8d12eb38de71/deck 2/10
3/15/2021 Fluid Lines And Fittings Flashcards | Chegg.com
A - Black
AN ttings have an identifying shoulder between the end of the threads and
the are cone.
AC and AN ttings are considered identical except for material composition
and identifying colors.
AN ttings are generally interchangeable with AC ttings of compatible
material composition.
A-1
8202. The maximum distance between end ttings to which a straight hose
assembly is to be connected is 50 inches. The minimum hose length to make
such a connection should be?
C - 52-1/2 inches.
https://www.chegg.com/flashcards/fluid-lines-and-fittings-0ea86c55-1da3-4d42-81cf-8d12eb38de71/deck 3/10
3/15/2021 Fluid Lines And Fittings Flashcards | Chegg.com
8204. The material speci cations for a certain aircraft require that a
replacement oil line be fabricated from 3/4 inch 0.072 5052-0 aluminum alloy
tubing. What is the inside dimension of the tubing?
A - 0.606 inch
8206. Which statement(s) about Military Standard(MS) are less ttings is/are
correct?
A-1
8207. When aring aluminum tubing for use with AN ttings, the are angle
must be?
A - 37 degree
C - inside diameter
8209-1. When a Te on hose has been in service for a time, what condition may
have occurred and/or what precaution should be taken when it is temporarily
removed for the aircraft?
C - the hose may have developed a set, or have been manufactured with a
pre-set shape, and must be supported to maintain its shape.
Prep
A - appear in the heel of a bend
8211. Which of the following hose materials are compatible with phosphate-
ester base hydraulic uids?
Butyl
Te on
Buna-N
Neoprene
A - 1 and 2
8214-1. The best tool to use when cutting aluminum tubing, or any tubing or
moderately soft metal is a?
https://www.chegg.com/flashcards/fluid-lines-and-fittings-0ea86c55-1da3-4d42-81cf-8d12eb38de71/deck 6/10
3/15/2021 Fluid Lines And Fittings Flashcards | Chegg.com
Prep
A - hand operated wheel-type tubing cutter.
8215. A gas or uid line marked with the letters PHDN is?
8215-2. If a ared tube coupling nut is over tightened, where is the tube most
likely to be weakened/damaged?
https://www.chegg.com/flashcards/fluid-lines-and-fittings-0ea86c55-1da3-4d42-81cf-8d12eb38de71/deck 7/10
3/15/2021 Fluid Lines And Fittings Flashcards | Chegg.com
Prep
8216. Which statement concerning Bernoulli's principle is true?
B - the pressure of a uid decreases at points where the velocity of the uid
increases.
8217. (1) Bonded clamps are used for support when installing metal tubing.
(2) Un-bonded clamps are used for support when installing wiring.
8218. A 3/8 inch aircraft high pressure exible hose as compared to 3/8 inch
metal tubing used in the same system will?
16 cards
https://www.chegg.com/flashcards/fluid-lines-and-fittings-0ea86c55-1da3-4d42-81cf-8d12eb38de71/deck 8/10
3/15/2021 Fluid Lines And Fittings Flashcards | Chegg.com
Prep
Material Science Ch 8
Equations And Terms
34 cards Shanna M.
Ch. 39 Bone
Biomechanics And Fx ...
COMPANY
CHEGG NETWORK
CUSTOMER SERVICE
https://www.chegg.com/flashcards/fluid-lines-and-fittings-0ea86c55-1da3-4d42-81cf-8d12eb38de71/deck 9/10
3/15/2021 Fluid Lines And Fittings Flashcards | Chegg.com
Prep
https://www.chegg.com/flashcards/fluid-lines-and-fittings-0ea86c55-1da3-4d42-81cf-8d12eb38de71/deck 10/10