Professional Documents
Culture Documents
Threaded Closures: Sizes: 4" Through 14"
Threaded Closures: Sizes: 4" Through 14"
T. D. Williamson, Inc.
Options*
TDW Pigging Products P.O. Box 1121 Tulsa, Oklahoma 74101-1121 918-447-5400 Fax: 918-664-7091 www.tdwilliamson.com
Data subject to change without notice. / Dimensions not for construction unless certified. / ® Registered trademark of T.D. Williamson, Inc. in the United States and foreign countries / TM Registered trademark of T.D. Williamson, Inc. in the United States and foreign countries / © Copyright 1997. All rights reserved T.D. Williamson, Inc. / Printed in USA
Dimensions and Part Numbers TDW
T. D. Williamson, Inc.
Threaded Closure Without Hinge
Sizes 4” through 8”
B Nominal
Pipe OD
A
C
E
B
Nominal
Pipe OD
A C
TDW Pigging Products P.O. Box 1121 Tulsa, Oklahoma 74101-1121 918-447-5400 Fax: 918-664-7091 www.tdwilliamson.com
Data subject to change without notice. / Dimensions not for construction unless certified. / ® Registered trademark of T.D. Williamson, Inc. in the United States and foreign countries / TM Registered trademark of T.D. Williamson, Inc. in the United States and foreign countries / © Copyright 1997. All rights reserved T.D. Williamson, Inc. / Printed in USA
Pressure & Temperature Ratings TDW
T. D. Williamson, Inc.
Pressure Ratings
per ASME Codes for Pressure Piping and ASME B&PV Code for TDW Threaded Closures
Pressures do not include allowance for corrosion. Pressures are in pounds per square inch, gage (psig).
1
Closures may be taper-bored for thinner wall pipe or supplied with heavier bores than those listed. Note: Taper-bored closures may
result in decreased MAWPs; however, heavier bore closures will not result in increased MAWPs. Consult the factory for conditions not
listed.
2
ASME B31.8 paragraph 831.373 requires that maximum allowable stresses for material used in closure heads not exceed 60% SMYS
and paragraph 841.121 requires that fabricated assemblies be designed at least to the design factor of 0.60.
Allowable test pressures in accordance with requirements of applicable ASME code. Consult the factory for appropriate values. TDW
shop pressure testing optional.
Temperature Ratings
-20°F (-29°C) to 250°F (121°C)
Temperatures greater than 250°F (121°C) and less than or equal to 500°F (242°C) at reduced MAWP with suitable O-Ring material.
Replacement O-Rings
Nominal Pressure Warning Lock Primary Seal Dust Seal
Pipe Size O-Ring O-Ring O-Ring
4 00-0115-0004 00-0117-0027 00-0117-0045
6 00-0115-0004 00-0118-0040 00-1386-0008
8 00-0115-0004 00-0118-0041 00-1386-0009
10 00-0115-0025 00-0118-0039 00-1386-0010
12 00-0115-0025 00-0119-0037 00-1386-0011
14 00-0115-0025 00-0119-0018 00-1386-0012
Standard O-Ring material is 70 Durometer Nitrile (Buna-N).
Other compounds may be substituted to meet service requirements.
TDW Pigging Products P.O. Box 1121 Tulsa, Oklahoma 74101-1121 918-447-5400 Fax: 918-664-7091 www.tdwilliamson.com
Data subject to change without notice. / Dimensions not for construction unless certified. / ® Registered trademark of T.D. Williamson, Inc. in the United States and foreign countries / TM Registered trademark of T.D. Williamson, Inc. in the United States and foreign countries / © Copyright 1997. All rights reserved T.D. Williamson, Inc. / Printed in USA