Bluewater Energy Sovns BY.
orstraa 3
SI Hr etdcorp
0. be 02, 2130 KC Hatérp
The Netheronde
Teli 29 69 000
Foc 13123 5s 2055,
‘movers
Pl Re Fi
Project: BLUEWATER STANDARD PROJECT
Document No: | BwS | C | 100| PR_|9906| 001 | 1
Te Behe co
Installation/Reference: BWS
Current rewslons are Wetiied on the relevant page(s) by 8 vertical ne Inthe raht-hand marin
‘adjoent to where the revion was made Al previo reson Kentiiclion s terved.
ages e4re _
2 Codes and Standards.
3x1 General Repair Procedure of Localized and Cored Se on Weather Som areas ke
‘ecommeration, Topsis ec: a
3.1.1 Surface Preparation - 5
3.1.2 Paint Application 5
3.1.3 Paint Repair Syste fr Weather Exposed AEBS un =e
532 General Refurbishment Procedure of Crroded area and Scared Seon esther Some
ares lke Accommodation, Tepsides et 6
3.21 Surface Preparation =
3.22 Paint Application. 6
323 _Refrbshing Pat Sytem for Weather Exposed es: 8
33 Repa Procedure of Localized and Cored Spots on Deck. m7
33.1. Surface Preparation 7
33.2 Paint Application 7
333 Paint Repair Sytem for Weather Exposed Deck 7
534 Refurbishment Procedure for Cored and Scattered Deck areas. 8
3.1 Surface Preparation 8
3.2 Paint Appcaton van 8
53433 _Refubhing Pat Sytem for Weather Exposed Dec. 8
15 Repair roceure of Lcazed and Coded Spots on Perk, Vessels, Toners and ater
RUMEN ns
B51 Surface Pepsin ssn
35.2. PalntApplation i
3:53 Paint Repair Sytem for Uve Pipewor..
336. General Repair of (Caroded) Supports wth Conedion between Sta and Staines St
346. Sisface Preparation,
36.2 Paint Appleton
3.6.3 Pant Repl Sytem or ive PpenOr
137. Rapa Procedure of Lecalzed ae Carded Spt Wes nina Seanater Exposed ASSL
37.4 Surface preparation —
3.72 Paint Appleaton = aL
3.73 Paint Repair System for Balast Tanks.
3.8 Repair rose of Locazed and Corroded Spt eld in Interna rude Ol Expo res! 12
381 Surface Preparation
3.8.2. Paint Application.
3.83. Paint Repalr System for Crude Ol Tanks:
nian Reser: 5 rae etisamen Ns SHS. 100 SEHR.
"cares ng Raa Ss
39 Repair Procedure of Localized and Corded Spots/Welds in Slop Tanks wit an Ack Envronment:13
39.1 Surface Preparation ss 3
39.2 PalntAppICALION veer as
39.3 Paint Repair System fr Sip Tanks renal
3.10 Repar Procure f Leaves and Corded Spt Welds nV Spaces, Caferdams at
BA0.1 Surface Preparation sn Se
310.2. Appeatin nn a4
3.103 Paint Repair System for Vid Spaces and Coferdams 4
Irate 5 raged te1 Introduction
Der 100-6 4.
jc Bent Seno Pct
"poser ar apa Fe
“his Procedure has been prepared for panting and costing acts ding maintenance for
Foatng Production, Storage and Ofloacing Syste,
2 Codes and Standards
S0-850i-4
reparation of Steel subsites before aplcation of pals and
related preducs/isual assessment of surface cealiness Par 1:
ust grades and preparation grades of uncoated steel substrates
and of steel substrate after avral removal of previous contigs.
Preparation of Stel substrates before application of paints and |
reltedproducs/Visal assessment of surface ceeniness Part 2:
Preparation grades of previously costed ste! substrates after
localised removal of pevous pats.
Preparation of Stel substrates before appleation of paints and
‘elated product/s assessment o surface ceaiiness Pat
Preparation graces of eoated and uncoated sol suas freer
ronal of it ara previous coatgs by Hh Presre Wate ety,
15085003
‘reparation of te! surface before appleation of pants
Hand and power tool deaning
‘SSPCSPA
‘Surface preparation specication no. 1. Solvent Cleaning.
‘SSPC SPI2/NACE No
‘Srface reparation and deaning of steel and oer hard maria
by High and Uratigh Pressure Water jeting peor recasting.
‘SSPCVIS4/NACE No7
Trim gue and wSual reference photographs fr steel dean
by hye tng.
anne as
ona atten Ne B00 604.
Tree Suc Sen! oct
cee ten apr FPSO
Repair Procedures
General Repair Procedure of Localized and Corroded Spots on
Weather Exposed areas like Accommodation, Topsides etc:
3.4.1 Surface Preparation
‘+ Scraping ofall coraded sets n order to remove nor-andjior bad adhering paint
{High pressure wash with fresh water in order to remove sls, lose rust and other
‘contamination.
‘+ Remove all corrosion and other contarinatons preferably by very thorough spt lasting
(2.2% conform TSO. 8501-1), vacuum blasting, wet Bast technique (Gullbist or
‘equivalent or fgh Pressure Water Jetting (a 2¥s conform TSO 8501-4)
‘+ If blasting oF HRW are not an ono, remove al corrosion by power tool cleanin, such 3s
vwirebrushing, machie-brusing and grinding thoroughly, giving the surface a metalc
‘Sen (3 conform 1S0 8501-1) flowed by needle gun fF cesting an anchor prfie.
‘+ Roughen the adjacent area (ppces. 510 on)
‘+ Featherng the edges ofthe spot blast area by sandpapering
1 Gean the aoa of aust and other contamination. The surface shal be fee from wsble ol,
‘grease and di, and fom coatings and foreign mater.
‘+ Donat teat a Blgger area than can be cated the same day.
3.1.2 paint pplication
‘+ Touch up fist cost of Surface Tolerant Anticorosve primer on bare stel with 8 brush
1 ter 24 hours touch up witha second cost of Surface Tolerant Anioresve primer with
brush o role.
‘+ er'24 hours touch up with a ted coat of Sufoce Tolerant Anicorrosie primer with 9
brush o a rote.
‘+ Ater'24 nous touch up wit the topcoat.
+24 hours cure before exposed
notes:
+ Paint shall be applied according to Paint Manufacturer's speciation and tachical data
sheets
Colour is depending on location
"isi cots of pint shal be of eiours with contrast othe colour ofthe previous cat.
“Tune the elour ofthe second coat occlu of he final cat.
Incase of insukient fing power for some coous, tke yellow and bight oranges, I
night be necessary to apply an edtonl coat oer the topos
3.1.3. Palnt Repair System for Weather Exposed Areas:
‘Goat [Tope ‘Dit —[Taierational_[ Jaton ‘Signa
YU" | Surach TOSREA [SOS tee 670 tama Signer ST
‘eres piner aluminum Huntin | anim | Aumeion
TU Sutacs York A | S075 | Imre 670 | oan BO | Sgnacver 63
crosve pine HS ger x
7 Src Tosrant nl [S075 | lntrses 79 | oars o0 | Signer 6
erosive prime f te Hsoftwnme | aftwnte | ftv
TH [Paraiso [ S075 [ tne 0 | Fase [Sora 0
scree: 5 roesra432
rare BS-C1009R-9505 0 £
‘haat Buc ard oct
‘Mesases er ast Rep PO
General Refurbishment Procedure of Corroded area and Scattered
‘Spots on Weather Exposed areas like Accommodation, Topsides etc:
3.2. Surface Preparation
‘+ Scoping of al corroded spots in ode to remove non-andor bac adhering pint
{High pressure wash with fresh water in order to remove sls, lose rust and other
‘contamination,
‘+ Remove all corrosion and other contaminstons preferably by very thorough spot basting
(Go 2% conform 180 8501-1), vacium basing, wet blast techni (Qulblast oF
‘equivalent or High Pressure Water Jetting (We 2¥s conform 150 8501-4).
‘+ If biasing o HW are not an option, remove all corrosion by power tool deaning, such as
wie-brushing, machne-brushing and grinding throughly, ving the surface =| metalic
‘shoen (33 conform 150 8501-1) flawed by needle gu fr ceaing an anchor prt
‘+ Festerng the edges of the spot blast area by sandpaper
1 Roughen the entire area to be coated.
1 Glan the aea of aust and other contamination. The suface shal be fee from vsble ol,
freane and i, and from coatings and foreign mate,
‘+ Bonet teat bigger area than can be coated the same dy.
3.22 Paint Application
‘+ Touch up fist coat of Surface Tolerant Ancorosve primer on bare ste! wth 2 brush
{Touch up second coat of Surface Tolerant Anicomosve primer tha brush o rol.
1 AMter 24 hours apply afl cook of Srface Tera Aicorosve primer wth brush or
robe
‘+ Ate 24 pours a ful oat of topcoat can be applied.
{+ 2ahouts cure betore exposed
Notes:
+ Paint shall be applied according tn Paint Manufacturers speciation and technical data
sheets.
Ceteur is depending on location
ull coat of paint shal be of colours wth contrast to the colour of the previous coat
{Tune the colour ofthe second cot to colour ofthe fil oa
{nease of insuicent hiding power fr some colour, lke yellow and bright oranges, t
right be necessary to apply an addtional coat over the topost
3.2.3. fefurbiching Pant Systom for Weather Exposed Areas:
‘coat Type ‘Dt ternational —[ Jotun Sama
"TU | Sarees Taranto —— [S075 | Inersea 70 | tase WO | Sgracaner
{cree primer enn suman | dumelan | Alin
TU [Srace Tolerant An | 575 | ners 70 HS | otras BO | Seracover 3D
cera ime re, ge | ger oer
Fe | Stroce Tosrare att | S075 [Irs 70S | Stamamie | Sarco a0
resi rer tte seats ores | offi
Fe Pojrshane pcos) 50-75 ntti 390 | Haro HBAS] Strader 55D
~ = ses.
savers ramsoris33
aan BH 100897604.
Te Sn et
cee Ct apa FPS
Repair Procedure of Localized and Corroded Spots on Decks:
3.3.1 Surface Preparation
‘+ Tscate the are rom dust, weather, people walking trough, silage etcetera,
Saping of al corrded spts in oder to remove norandor bad adhering paint
{High-pressure wash with fresh watar In order to remove salts lose rust and other
‘contamination,
‘+ Remove all corrosion and other contaminatons preferably by very thorough spt lasting
(G2. 2% conform 150 8503-1), vacuum blasting, wet bast technique (Quliast oF
cequvalent or High Pressure Water Jetting (Wa 2¥: conform 50 8501-4)
‘+f biestng oF HRW are not an opto, remove al corrosion by power too! cleaning, such a
wrebnshing, machie-brusting and grinding thoroughly, aving the surface a mete
‘heen (53 conform 150 8501-1 flowed by needle gun for cresting an anchor profile.
‘+ Roughen the adjacent area (approx. 510 om)
Featering the edges ofthe spt blast area by sandpapering
1 Chan the aea of cst and other contarinaton The surface shal be fee fram vb of,
‘reece and i, and fom coatings and foreign mater.
‘+ Boro reat a bigger are than canbe coated the same day
3.32 Paint Application
“+ Touch up fist coat of Surface Tolerant Anicorosive primer on bare tel vith 9 brush
{Aft 2¢ hours touch up witha second cot of Surface Tolerant Aricorosve primer with 2
brush e rol
‘After 24 hours touch up with 2 third cost of Surface Tolerant Aniorosve primer with 2
brish e @ oli
‘+ AMter24 hours touch up withthe topooat
+ 2ahours cure before exposed and desolate the area,
Notes:
+ Paint shall be apped according to Paint Manufacturer's speciation and tochical data
shes
+ Mitpe coats of pant shal be of colours wih contrast othe colour ofthe previous coat,
3.3.3 alot Ropalr Sytem for Weather Exposed Decks:
coat pe Tor atu ‘Slama
TU Sutace Tosa Ab 75100 Suma 60) Sacer
TU | Siace Tolerant as | 75100] Irkenea 67OS | xamasi 60 | Saracover 6
TU [Sac Tolsant at——| 75100] ines @7OHS | rae
rove prime fe iui | aie
‘TW Epoe toe 5075. | sal 670 HS | Pengo
Tope
rete: OS e734cane: 10086 04.
ject Bert San oct
eres er tr apo FPS
Refurbishment Procedure for Corroded and Scattered Deck areas.
3.4.4 Surface Preparation
Isolate the area fam dst, weather, people wating tough, silage esters
{Scraping of al coreced spots in ader to remove na and/x bad adhering pint
{High pressure wash wih fesh water In order to remove sels, looke rst and other
‘contamination
+ Remove all coresion and other contaminations preferably by very thorough spot blasting
(S2 2% conform 1S0 8501-1), vacuum basting, wet blast technique (Gulblst oF
‘Sauivalnt) or High Pressure Water Jetting (a 2¥s conform 1S0 8501-4)
+ Tf basing or HPD ae act an epi, remene al coresion by power tea clearing, such a5.
\wirebrshing, machine brushing and greg thorough, sng the surface a metalic
sheen (St conform ISO 8501-1) folowed by needle gun fr creating an anchor profile.
+ Feathering the edges of the spot blast area by sandpaper
Roughen the entre area tobe cnated
{Clean the areo of dust and ater contamination. The surface shal be free from vibe ol,
‘grease and di, and from coatings and foreign attr.
+ Bonot teat Bigger area than can be coated the same day.
3.4.2 Paint application
+ Touch up frst coat of Surface Tolerant Aicorrosive primer on bare steel witha brush
{Touch up a second exat of Suace Tolerant Alcoresve primer With a bh,
1 ater24 hours appt a ful coat of Imermedate coating with 3 brush oF 2 oe.
‘Mer 24 hours 2 fl coat of tpoaat canbe apes.
2a hous cure before exposed
‘+ Paint shall be applied according to Paint Manufacturer's specication and technical data
sheets.
‘+ Mule coats of paint shall be of colours with contrast tothe colour ofthe previous coat
3.4.3. Refurbishing Paint System for Weather Exposed Decks:
‘oat [Type ‘Dat ternational [Jotun Sama
TU | Sutace Tomart ha} 7510 | Iterzl 67015 | Stamasie BD | Sarocone HO
reve rime luna auminun | dumaisn | Ani
| ace Tare 7500 [terse 67S [Stamasic BO] Siac
‘onesie pane ey rt oe oe
FE | iemesiteCpony | 75100 | Iter OVE | Stamaie | Semacorer 0
coat state aentae | tet
FE ony tpt GETS | ness 70S | Penguré | Serena aSe
- Toxo
sere 5 remsarts35
Tho Sumter
‘esses ay Ra POS
Repair Procedure of Localized and Corroded Spots on Pipework,
Vessels, Towers and other Equipment:
3.5.1 Surface Preparation
+ Scraping ofall coroded spots in ererto remove nar-andor bad adhering paint
‘figh pressure wash with fresh water in order to remove sls, loot rst and other
‘contamination
‘+ Shvent wash ofthe corroded and ajacent areas
{Preferably remove all corrosion and oer containations by very thorough spat blasting
(Ga.2¥4 conform 150 850-1) by wet Bast technique (gllast or equvalent) oF High
Pressure Water tng (Wa 2¥ conform ISO @S01~)-
‘+ If basting oF HPWD are not allowed, remove all corrosion by hand too! caning by non
sparking copper or bronze wire-brushes to St conform TSO 8501-1,
‘+ Roughen the adjacent ares (appro, 5-10 cm) with wet lasting oF sandpaperng
4 Featherng the edges ofthe sot bast ares by sandpapering
1 Gan he aces of cist and ather contarinalon. The surface shall be fee tom visible ol,
‘ase and dt and fom coatings an forean mater.
+ Do nt reat a bager area than canbe coated the same day
35.2 Paint Application
‘+ Touch up at coat of Surface Tolerant Anicoraive primer on bare tel wth a brush.
{ter 2¢hours touch up with a second coat of Surface Tolerant Aniorosive primer witha
‘ruth ora rer
‘+ Ate 24 hours touch up with a the coat of Surface Tolerant Anicrosive primer witha
‘ruth or 2 rte
‘+ After 24 hours touch up with the topcoat
+ 2ahours eure betore exposed.
NoTES:
‘Paint stall be applied according to Pant Manufacturers speciation and technical data
hosts,
“+ Malte costs of paint shall be of colours with contrast tothe colour ofthe previous cst.
35.3 Paint Repair System for Live Pipework:
Seat [ee _____— on [ternational —[yoeon Tam
‘Sie Taeane an $078 Intel 70 HS | otamanie | Samer BD
"| eres rime ina Summ | 80umisam | Amn
TW | Siroes Towra [5075 [ntseal 6705 | aotamasse | Syracoer 6D
Looe srimer rey. |_| ary oar ra
TU | Siac Tosrane so) [ 5075 | Inara SPOS [Stamacie —] Shmacrer
crave iner nhte snes barewnte | one
[ro Potaretiane openst P5075 nertane950 | Maroy. | Smadur 550
HAAS gosme Ne: 5-600 041
ce Sst or Os
General Repair of (Corroded) Supports with Connection between
Steel and Stainless Steel:
6.1 Surface Preparation
1 Scraping of al coreded spots in order to remove norandor bad adhering paint
{High pressures wash with fresh water In order to remove salts, loose ust and other
cortamiatin (both steal and stares tel.
‘Solvent wash ofthe corroded nd adjacent areas
{Remove all corrosion and other contaminatons preferably by very thorough spt blasting
(G2 2% conform 150” 8503-1), vacuum blasting, wet bast technique (Qulbast oF
‘equvalert or High Pressure Water Jetting (We 272 conform 1S0 8801-4).
‘+ Before the appleation of any point Sainiess tee! surfaces sal be Ceaned, degreased
‘and sweep Basted ith noremetalc ad chide free grt to obtain an anchor rofl of
‘2pproximatty 25m to 45 pm, Before small parts or areas Ris alowed to sandpaper th
‘Sails: sta wire wo!) with Sandpaper
+ Roughen the adjaant area (approx 510 on)
{Chan the area of dust and other contamination The surface shal be fee from vsble of,
‘reane and dit, and from coatings and foreign mater.
‘+ Bonet teat bigger area than canbe coated the same day
3.6.2 Paint Application
Apply fest coat of Suface Tolerant Antcorrosive primer with 3 brush over steel and
Stare ste! part (510 cm)
‘+ After 24 hous apply a second cost of Surface Tolerant Amcorrosive primer with roller
‘andr bush over steel an stains sel pat (5-10 on).
‘+ Aer 24 hours appr third coat of Surface Tolerant Aniorosve prime wth a rush o @
robe
‘Aer 24 hours the topcoat canbe appl.
2 2a hours cure before exposes
Notes:
‘Paint shal be appied according to Pant Manufacturer’ specication and technical data
heat,
“+ Mull costs of paint shal be of colours wth contrast to the colour ofthe previous coat
4 Golo s depending on locaton
‘+ In-case of insufient hing power for some colours, ke yellow and bright oranges, it
might be necessary to apply an adtonal coat oer the topoast
3.6.3 Paint Repair System for Live Pipework:
‘coat Type ‘Dit Taierational [tun
Fe | Surscr TaRaneAa [S075 | nts 7S [sata | Sacer 2
‘rose primer aluminum =tmum
Sima
Fo | Sie Taare ia | SOS | Ta STOW wey | SaaasC | Soman ST
‘rose pine rt a
FE | SurecsTorertal| S075 | Taal OAS [Soamaaie 8] Soman
‘ese primer tite ‘tana | omit
tne
Fe Pojureshanetopcat | 5075 | Teena 990 | Harton Saar 550
HBAS goss
nsec: BS oe 1001437
Repair Procedure of Localized and Corroded Spots/Welds in Internal
‘Seawater Exposed Areas:
3.7.1 Surface preparation
‘+ Scraping f al corroded spss oder to remove non-andfor bad adhering paint
{High pressure wash with fresh water In order to remewe sal, loose rust and other
‘entamination,
‘+ Remove al corrosion and other contamination preferably by very thorough spot Basti
(Go 2v conform 1S0 8501-1), vacuum basing, wet Hast technique (Qullast ot
‘qutalnt) or High Pressure Water Jetng (Wa 2 conform 150 8501-4).
‘+ lasing or HPWS are not an option, remove all corrsion by power tol deaning, such as
wire-brushing, machine-bushing and grinding thoroughly, veg the surface 2 metic
sheen (SE conform ISO 8501-1) followed by needle gun for creating an anchor prof
‘+ Roughen the adjacent area (approx. 510 cn)
Featherng the edges ofthe spt blast area by sandpapering
{Glan the area of cust and other contamination. The surface shal be free from vile of,
‘grease and dit and rem coatings and foregn matter.
3.7.2 Paint Application
“+ Apply st coat of Surface Tolerant Antiorasve tank coating wth 2 bush. If nt beable
to apply Inthe specified dry fm ticiness, apply after 2 hours but within 4 hours an
addralexat Surface Tolerant Aricoresve tank coating inorder to get the required dry
fim tenes, this a wet In wet appleston. IF thls cant be done than te second coat
stall be applied after 24 hours.
+ ter 24 hours the second tank coating can be applied. If not be able to apply inthe
pected ry fm thikoess, apply after 2 hours bat wihin 4 hous an adonal coat tank
ating in order to get the aque ry fm thickness, ts isa wet in wet applaton. If
{his cannot be done than the second coat shall be applied after 28 hours
+ hours eure before expose,
NoTE:
‘+ Wh brush andor rler the max thicness i approx. 50-75 um, there fortwo applcaon
‘ofeach coat wil hae to be done to get te requlre fm thickness oF 125 um,
‘+ Paint shall be apple according to Paint Manufactures speciation and technical data
shes,
+ Multpe coats of paint shal be of colours with contrast to the colour ofthe previous cot.
3.7.3 Paint Repair System for Ballast Tanks:
[coats arteries —
TU | Surece Toes ars [125-—| Itsel 670- FS | Boxy FUG | SorGard 290
TW [rs Tork costing | 2S | irtrsal 67S | Bliny HO URE | SanaGure 0 |
rataeteen OHS roxas38
hg Suen ence rat
‘Pecaes to oan Rea OS
Repair Procedure of Localized and Corroded Spots/Welds in Internal
‘Crude Oil Exposed Areas:
3.8.1 Surface Preparation
+ Scraping ofa coroded spots inorder to remove non-andor bad adhering pot
{High pressure wash wih fresh water In order to remove sas, lose rust nd other
conaminton.
+ Remove a orosion ond ther contamination preferably by very thorough spet blasting
(Go"2% conform TSO" 8501-1), vacuum biting, wet blast tecdniqe (Quast oF
‘uivaent) or High Pressure Water Jetng (Wa 2¥2 conform 150 8501-1).
+ If blasting oF HPW) are nat on opto, remove al corrosion by power oo ceaning, Such as
wire-brushing, machine-brushing and gndng thoroughly, aving the surface a metalic
Sheen (S13 conform 1S0 850-1) followed ty neede gun for creating an anchor prof
+ Roughen the adacent area (approx, 5-10 an)
1 Feathering the edges ofthe spot bast area by sandpapering
{Gen the ea of dst and athe contamination The surface shall be fee from vsble ol,
‘tease and i, a fom coatings and foresgn mater.
3.8.2 Paint Application
+ Apply fst coat of Aticorasive tank coating vith 2 brush
‘Fat beable to app inthe speed dry im thickness, aply ater 2 hours but within 4
hours an addtional coat Asicorosive tank exaling inorder to get the reqied dy fi
thikness, this isa wet in wet appleation. I this cannot be done than the second coat shal
be apled ater 24 hours
‘+ After 2 hours the second tank coating canbe apple.
‘trot beable to appt in the speed oy fin thickness, apply after 2 hours but within 4
‘ours an adhe coat
‘+ Aer 24 hours the fal tank coating canbe apo
1 2ahours cue before exposed
Note:
‘+ With brush andor roller the max thickness approx. 50-75 yen therfore two application
‘ofeach coat wl have to be done to et the requred fm thickness of 125 ym
‘+ Paint shall be applied according to Paint Manufacturers speciation and technical data
sheets
‘+ Multi coats of paint shall be of colours with contrast to the colour ofthe previous coat
3 Paint Repair System for Crude OW Tanks:
‘oat Type “dR [Sntematonal[Sokun ‘Sams
TU" | Atcareave [125 | tmarmi 300 | Tankard paca | Somacove 25 (0
pine sum)
TO [RS Tank csing [TAS | iarvas HO | Tanga Space wa_| Soma Novauard 200
ation)
FO) RS anc | S| ara Tear Spal Te” Soma Nova 200
iaeisoum
een ere: roe est39
Tiga ae anc Rae
Tce Cosa ken FD
Repair Procedure of Localized and Corraded Spots/Welds in Slop
‘Tanks with an Acid Environment:
9.1 Surface Preparation
+ Scraping of at coded spot inorder to remove ron-andor bd adhering pant
‘ih pressure wash with fresh water in order to remove sas, lose rust and other
‘ottamination.
‘+ Remove all oroslon and ther contamination preferably by very thorough spot blasting
(So 2% conform 130 8501-1), vacuum blasting, wet blast technique (Guillast or
‘culvatent) or Hh Pressure Water Jeting (Wa 2¥2 conform 150 8501-4).
‘+ IF blasting or HWA are not an option, remove al corrosion by power tool desning, such 2s
vwirebrushing, machine oushing and grinding thoroughly, ging the surface ® metalic
‘Shean (St conform 150 850-1) followed by needle gun for eating an anchor pote
‘+ Roughen the adjacent area (approx. 5-10 cm)
1 eatherng the aspes ofthe spat bast are by sandpapering
{Gen the area of cist and other contamination. The surface shal be fe from visble ol,
‘grease ard it, and fem coatings and foreign matter.
2. Paint Application
1+ Aoply fest cot of Aricorosive tank coating wth 3 brs. If not be able to apply inthe
speced dry fim thickness, apply after 2 hours but within # ours an addteal coat
‘corrosive tank coating in Order to get the requred ry fin thickness, his sa wet
‘wet appaion. If is cant be dove then the second coat sha be appa ater 24
rows
+ Afar 24 hours the second tank coating can be applied. If not be abe to apply i the
pected dry fl thickness, apply ater 2 hours bat within 4 hows an edllonal coat tank
asin in ardor to get the eure dry fm thickness, ts 19 wet ln Wet appeaton. Tf
{his cannot be done than the second coat shall be appl after 24 hours,
‘+ After 24 hours the fil tank coating can be appled
+ thous cure betore expose,
Nore:
‘+ wth tush andor rl the mie hes pprax. 5075 ym, therfore two appeaon ofeach
att have tobe done to get the rere fn eso 125m
+ Pant stalbe pod according to Part Manacurer’s pectin ad tech data seas
1 mati caso pit sabe of clus with cars to the sour of he resus cot
32.9.3 Paint Repair System for Sop Tanks:
‘oat_[Type [a tarotionat_[ Jotun Sama,
TU" | et cave [125 | inersied 300” | Targa Spacal | SanaPhenguad S30
z (gt 100ym)
Tu [sank 125 ~| erat 300” Taare pec | Smad 70
‘tng 50m
TO |S tank 125 Tred 300 Tana Sec Top | Samacuad 70
cng 30m)
neater: BS Pom serterae SS 100-00 Ren +
"hoe Buent nar Moh
"Pease ase ep 0
3.10 Repair Procedure of Localized and Corroded Spots/Welds In Void
Spaces, Cofferdams etc.:
3.40.1. Surface Preparation
‘+ Scraping fal corred spts in ode to remove non-andor bed adhering plnt
{High pressure wash wth fresh water In order to remove Sas, lose rust and other
‘contamination,
‘+ Remove al corrosion and other contamination preferably by very through spot basting
(S2 2% conform 1S0 SDI-1), vacuum biasing, wet Hast technique (Qullast ot
{qutalent) or High Pressure Water etn (Wa 2s conform 150 8501-4).
‘+ lasting or HPA are not an option remove all corrsion by power tool cleanin, such as
|wiesbrusing, machinebrushing and gandng therougly, gving the suface a metalic
sheen (St conform ISO 8501-1) followed by neediequn for creating an anchor prof
‘+ Roughen the aejacent area (aprox. 510 cm)
Featering the edges ofthe spot blast area by sandpapering
1 Glan the aren of cust and other contamination. The srface shal be free from vesble ol,
srease and dit and rem eoatings and foegn mater
3.40.2. Application
“+ Appl fest coat of Surface Tolerant Aoticorrosive coating wth a brush
‘After 2 hours but within 4 hours apply 2 second coat of Surface Tolerant Artcorosive
ating in order to get the required dry fim thickness, ts is @ wet in wet applaton. If
ths cannot be done than the second coat shall be applied ater 24 hours
+ With brush andr role the max thickness is appro 50-75 um, therfore two aplication
‘ofeach cos wt have to be done to get the requtred fim thickness of 125 un
‘+ Paint shall be apped according to Paint Manufacturers speciation and technical data
sheets.
3.10.3 Paint Repair System for Void Spaces and Cofferdams:
‘oat [Type ‘a tniemational [Jotun Sama
| Sreeraeea [Yr 70 [Be FET Sea Hi
natreteren: BS Page Mott