14-O9T.' O5 (MAR) 09:45
. Manual For PALL ROCHE Water Desalination Unit
ROCHE NARINE GE
PAX: +#39010543257 Pool
561-2
ACTUATOR
Main Components
24
23
} 22
2 a
2 eh
3 1
4 = Part No. Description
= 2 4 Cover
> 8 2 Capacitor
5 ” 3 Motor
s—t Ee 4 O-Ring
7 5 Gears
i 6 Hand Wheel
e 20 7 Pressure Spring
9———__+ 8 Uncoupling Lever
9 O-Ring
8 10 Wiping Ring
10: W Antl-Rotation Flange
12 Threaded Bushing
15, 13 Scale
u 4 14 Scale Clamp
a 15 Support
d T 16 Intermediate Flange
17 Cable Bushing
z 18 Gasket Seal
re 19 Torque Switches
Fig 1 20 Actuator Spindle
5 21 Terminal Strips
22 Switching & Signalling
Device
23 Gasket
“a 24 Cap Nut
Fig 2
7100-92-0398
Thi14-097,“ O5 (MAR) 09:46 ROCHEM MARINE GE PAX: ++39010545257 P, 002
Menuai For PALL ROCHE Water Desalination Unit 861-3
ACTUATOR
ie a Tei Manual ControlofValve sis os Tet ghee |
This valve can be manually operated by :
“A” The Uncoupling Lever and "B" The Hand Wheel.
» To open or close the valve pull down the uncoupling lever to dis-engage the
motor drive and turn the hand wheel
The lever is spring loaded and will re-engage when released
Turn hand wheel Clockwise to Close. Anti clockwise to Open
Aes Power Supply and Controls
For units controlled by a A020-Plus processor, the diagram below shows the inter
conneetions between the control panel ‘and the actuator, For Units controlled by other
processors see the electrical schematics for the correct cabinet terminal connections.
a
| | 7020. PLUS CONTROL CABINET TERMINAL CONNECTION BOARD
| NI 4 [al 154] 74175
| | 220v |
| cuosms OPEN iil er soso
|
(t[2lel4islel7 ele lio vilaalta|14] 15] 16 [17] 18] 19 20 24 [22] 28 alas) |
A l |
pl . yl
DE DE We WE
st 82 34 85
\ MOTOR CONTROL VALVE ACTUATOR
7400-32-038814-017. 05 (MAR) 09:46 ROCHEM MARINE GE PAX:++39010845257 P.005
Manual For PALL R@GHEA Water Desalination Unit 61-4
ACTUATOR
[ Controls
There are 4 limit switches fitted in this actuator
DES1 DE S2 WE S4 WE S5
This iasafety | Thisisasefety | This is an indicator switch | This ie an indicator
witch to prevent | switch to prevent | to signal the Ad20 switch to signal the
Sver torque on | over torque on _| processor of the valve ‘A020 processor of
opening closing position (open) the valve position
| (closed)
[Torque Switches DE S1_and DE S2
The 2 torque switches S1 and $2 shown in
this photograhph must not be adjusted as
they are
“Factory Set’.
Way Switches WE S4 and WE S5
To prevent the forque switches S1 and S2 deing activated the way switches $4 and S5 are
always set between the settings of Stand S2.
Checking or re-setting the position ‘of switches S4 and SS should be carried out es follows:
Switch off power to the R.O. Unit.
Remove the nut gaskat,cover and gasket seal, Items 24,23,1 and 18.
4st check /set the OPEN switch S4
Engage the manual control by pressing down the uncoupling lever.
Tum the hand wheel ANTI-CLOCKWISE to open the valve
When resistance is felt stop turning the handwhee!
Use the valve postion pointer and mark the spindle position on the Scale plate.
Re-engage the manual control and turn the hand wheel CLOCKWISE intl the pointer
hes moved towards the closed position by 1mm.
ONOARYNS
7100-32-039814-077. ' 05 (MAR| 09:47 ROCHEM MARINE GE PAX:+#39010545257 7.0
5 04
Manual For PALL ROCHEM Water Desalination Unit 561-5
ACTUATOR
Way Switches WE S4 and WE S5. 3
Gee below for correct position of the cams on the inner switch. Cam position for the
valve to be full open.
40. Adjust the cams as follows:
Oa. Free the lock nut on the shaft, do not take it off
406, Slacken the milled nut to allow the cams to move.
{Oe Position the cams for the inner switch as shown below and hand tighten the milled nut.
44, Re-engage the manual contro} and turn the hand wheel CLOCKWISE until resistance is
felt then stop. |
42. Use the valve postion pointer and mark the spindle position on the Scale plate.
43. Re-engage the manual control and turn the hand wheel ANTI-CLOCKWISE unt! the
pointer has moved towards the open positicn by (mm.
44, Hold the inner cams in their pre-set position while vary carefully releaseing the milled
nut
and position the cams on the outer switch. Tighten the milled nut when the cams are as
shown below. Cam position for the valve to be closed.
15. Secure the cam assembly by tightening the Jock nut.
46, Way switches $4 and $5 are now correctly set.
Stroxe Adjuster and Way Switches WE S84 and WE $5
Stroke Adjuster
4. - Limit Switch
ta- Valve Open ‘Switch
4b- Valve Closed Switch
2 - Milled Nut
3 - Cam Plate
4 - Potentiometer
5 - Position Scale
8 - Adjustment lever system
7 -Locknut
WE S4
{inner switch)
in switched
OPEN position
WE $8
(outer switch)
In switched
CLOSED position
‘rann-92.0398