Professional Documents
Culture Documents
Technical Publications: Revision 1
Technical Publications: Revision 1
Publications
2274624
Revision 1
Operating Documentation
GE MEDICAL SYSTEMS FLOPPY DISK DRIVE REPLACEMENT MANUAL
REV 0 2274624
a
GE MEDICAL SYSTEMS FLOPPY DISK DRIVE REPLACEMENT MANUAL
REV 0 2274624
b
GE MEDICAL SYSTEMS FLOPPY DISK DRIVE REPLACEMENT MANUAL
REV 0 2274624
In performing all electrical work on these products, GE will use its own specially trained field engineers. All of GE’s electrical
work on these products will comply with the requirements of the applicable electrical codes.
The purchaser of GE equipment shall only utilize qualified personnel (i.e., GE’s field engineers, personnel of third-party
service companies with equivalent training, or licensed electricians) to perform electrical servicing on the equipment.
c
GE MEDICAL SYSTEMS FLOPPY DISK DRIVE REPLACEMENT MANUAL
REV 0 2274624
DAMAGE IN TRANSPORTATION
All packages should be closely examined at time of delivery. If damage is apparent, have notation “damage in
shipment” written on all copies of the freight or express bill before delivery is accepted or “signed for” by a General
Electric representative or a hospital receiving agent. Whether noted or concealed, damage MUST be reported to the
carrier immediately upon discovery, or in any event, within 14 days after receipt, and the contents and containers held
for inspection by the carrier. A transportation company will not pay a claim for damage if an inspection is not requested
within this 14 day period.
Call Traffic and Transportation, Milwaukee, WI (414) 827–3449 / 8*285–3449 immediately after damage is found. At
this time be ready to supply name of carrier, delivery date, consignee name, freight or express bill number, item
damaged and extent of damage.
Complete instructions regarding claim procedure are found in Section “S” of the Policy & Procedure Bulletins.
GE personnel, please use the GEMS CQA Process to report all omissions, errors, and defects in this documentation.
Customers, please contact your GE Sales or Service represenatives.
CAUTION
Do not use the following devices near this equipment. Use of these devices near this equipment could cause
this equipment to malfunction.
Devices which intrinsically transmit radio waves such as; cellular phone, radio transceiver, mobile radio transmitter,
radio–controlled toy, etc.
Keep power to these devices turned off when near this equipment.
Medical staff in charge of this equipment is required to instruct technicians, patients and other people who may be
around this equipment to fully comply with the above regulation.
d
GE MEDICAL SYSTEMS FLOPPY DISK DRIVE REPLACEMENT MANUAL
REV 1 2274624
REVISION HISTORY
PAGE REV PAGE REV PAGE REV PAGE REV PAGE REV
Title page . . . . . . . . . 1 i.................. 0 Tab 2 Tab 3
Title page rear . blank 2–1 . . . . . . . . . . . . . . . 1 3–1 to 3–14 . . . . . . . . 1 Blank/Rear cover . . . –
a to d . . . . . . . . . . . . . 0 Tab 1
A ................. 1 1–1 to 1–2 . . . . . . . . . 1
A
GE MEDICAL SYSTEMS FLOPPY DISK DRIVE REPLACEMENT MANUAL
blank 2274624
B
GE MEDICAL SYSTEMS FLOPPY DISK DRIVE REPLACEMENT MANUAL
REV 0 2274624
TABLE OF CONTENTS
SECTION PAGE
i
GE MEDICAL SYSTEMS FLOPPY DISK DRIVE REPLACEMENT MANUAL
blank 2274624
ii
GE MEDICAL SYSTEMS FLOPPY DISK DRIVE REPLACEMENT MANUAL
REV 1 2274624
SECTION 1 – INTRODUCTION
This kit replaces the U0012ZA Floppy Disk Drive with the 2349231 (or 2191376) Floppy Disk Drive. (The U0012ZA
FDD will be soon discontinued.)
White
Black
Zj ProSeed, ProSeed Accell, ProSpeed, ProSpeed VX, ProSeed EF, ProSeed Accell EI, ProSpeed Plus
Qj ProSpeed S, ProSpeed SX, Lemage, ProSpeed, ProSpeed S Fast, ProSpeed SX Power, Lemage SX/E,
Lemage SX, ProSpeed (with SSD Option), ProSpeed SX Power (with SSD Option),
ProSpeed SX Advantage, Lemage Supreme
1–1
GE MEDICAL SYSTEMS FLOPPY DISK DRIVE REPLACEMENT MANUAL
REV 1 2274624
NOTICE
For Zj–Adv., Qj, XMj, SYj, and SLj, the CPW board, contained in the OC, controls the FDD.
For compatibility between the CPW board and FDD, see the table below.
1–2
GE MEDICAL SYSTEMS FLOPPY DISK DRIVE REPLACEMENT MANUAL
REV 1 2274624
2–1
GE MEDICAL SYSTEMS FLOPPY DISK DRIVE REPLACEMENT MANUAL
blank 2274624
2–2
GE MEDICAL SYSTEMS FLOPPY DISK DRIVE REPLACEMENT MANUAL
REV 1 2274624
3-1-1 Removal
1. Power OFF the main switch of the OC.
OC FRONT PANEL
4. Remove the FDD power cable and signal cable from the FDD.
5. Remove the FDD from the FDD bracket by removing the four mounting bolts (reused).
SCREWS (REUSED)
3–1
GE MEDICAL SYSTEMS FLOPPY DISK DRIVE REPLACEMENT MANUAL
REV 1 2274624
G
F
E
D
C
B
A
2. Set the left and right FDD brackets, shipped with this kit, on the new FDD with the oval screw hole backward.
Screws (N9306HR)
4. Connect the FDD Signal Cable Assy and Power Cable Assy between the new FDD and VFO Assy.
3–2
GE MEDICAL SYSTEMS FLOPPY DISK DRIVE REPLACEMENT MANUAL
REV 1 2274624
Insulated Sheet
Power Cable
6. Install the VFO Assy onto the insulated sheet using the six screws (N9304JS).
Screws (N9304JS)
VFO Assy
3–3
GE MEDICAL SYSTEMS FLOPPY DISK DRIVE REPLACEMENT MANUAL
REV 1 2274624
3-1-3 Installation
Install the new FDD Assy in the reverse order of removal.
2. Insert a blank floppy diskette into the FDD, then save/load an image to/from a floppy diskette.
3–4
GE MEDICAL SYSTEMS FLOPPY DISK DRIVE REPLACEMENT MANUAL
REV 1 2274624
3-2-1 Removal
1. Power OFF the main switch of the OC.
Top Cover
Rear Cover
Fan Assy
3–5
GE MEDICAL SYSTEMS FLOPPY DISK DRIVE REPLACEMENT MANUAL
REV 1 2274624
Screws
FDD Assy
Cables
Screws
7. Remove the FDD from the FDD bracket by removing the four mounting bolts (reused).
Screws
Bracket Screws
3–6
GE MEDICAL SYSTEMS FLOPPY DISK DRIVE REPLACEMENT MANUAL
REV 1 2274624
Screws (N9306HR)
3-2-3 Installation
Install the new FDD Assy in the reverse order of removal.
Note that the power and signal cables are connected properly to the new FDD Assy as shown.
Cables
FDD Assy
3–7
GE MEDICAL SYSTEMS FLOPPY DISK DRIVE REPLACEMENT MANUAL
REV 1 2274624
3-3-1 Removal
1. Power OFF the main switch of the OC.
Front/Upper Screws
NOTICE
Hold the FDD/MOD Assy when removing the rear mounting screws to prevent it from falling.
5. Remove the two rear FDD/MOD Assy mounting screws, then remove the FDD/MOD Assy rearward.
Rear Screws
3–8
GE MEDICAL SYSTEMS FLOPPY DISK DRIVE REPLACEMENT MANUAL
REV 1 2274624
7. Remove the FDD Assy mounting screws, then remove the FDD Assy from the bracket.
FDD Assy
Screws
Screw (N9306HR)
3–9
GE MEDICAL SYSTEMS FLOPPY DISK DRIVE REPLACEMENT MANUAL
REV 1 2274624
3-3-3 Installation
Install the new FDD Assy in the reverse order of removal.
3–10
GE MEDICAL SYSTEMS FLOPPY DISK DRIVE REPLACEMENT MANUAL
REV 1 2274624
3-4-1 Removal
1. Power OFF the main switch of the OC.
3. Remove the FDD with the bracket as an assembly, then remove the FDD from the bracket.
3-4-3 Installation
Install the new FDD Assy in the reverse order of removal.
3–11
GE MEDICAL SYSTEMS FLOPPY DISK DRIVE REPLACEMENT MANUAL
REV 1 2274624
3-5-1 Removal
1. Power OFF the main switch of the OC.
3. Remove the FDD Assy by removing the three screws, and disassemble them.
Discard the two brackets, but screws are reused.
Screws Screw
FDD Assy
G
F
E
D
C
B
A
3–12
GE MEDICAL SYSTEMS FLOPPY DISK DRIVE REPLACEMENT MANUAL
REV 1 2274624
3. Connect the FDD Signal Cable Assy and Power Cable Assy between the new FDD and VFO Assy.
4. Install the VFO Assy onto the insulated sheet using the six screws (N9304JS).
Insulated Sheet
3–13
GE MEDICAL SYSTEMS FLOPPY DISK DRIVE REPLACEMENT MANUAL
REV 1 2274624
3-5-3 Installation
1. Install the FDD support (2212884) to the OC using the two screws.
2. Install the FDD Assy using the three screws, noting that the cables between the FDD and VFO Assy are properly
routed as shown.
3. Connect the FDD signal and power cables to the VFO connectors.
3–14
GE Medical Systems: Telex 3797371
P.O. Box 414, Milwaukee, Wisconsin 53201 U.S.A.
(Asia, Pacific, Latin America, North America)